measurement ¶

The measurement commands module.

These commands are used in the following models: MSO2

THIS FILE IS AUTO-GENERATED, IT SHOULD NOT BE MANUALLY MODIFIED.

Please report an issue if one is found.

Commands and Queries

- MEASUrement:ADDMEAS {ACRMS|AMPlITUDE|AREA|BASE|BURSTWIDTH|DATARATE|DELAY|FALLSLEWRATE|FALLTIME|FREQUENCY|HIGHTIME|HOLD|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NWIDTTH|PDUTY|PERIOD|PHASE|PK2Pk|POVERSHOOT|PWIDTH|RISESLEWRATE|RISETIME|RMS|SETUP|SKEW|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TOP}
- MEASUrement:ADDNew 'QString'
- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?
- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?
- MEASUrement:DELETEALL
- MEASUrement:DELete <QString>
- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:EDGE<x>?
- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?
- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?
- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?
- MEASUrement:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?
- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?
- MEASUrement:GATing:SEARCHSource SEARCH<x>
- MEASUrement:GATing:SEARCHSource?
- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?
- MEASUrement:GATing?
- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?
- MEASUrement:LIST?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?
- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?
- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?
- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?
- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?
- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:MEAS<x>:EDGE<x>?
- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?
- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?
- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?
- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?
- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?
- MEASUrement:MEAS<x>:FAILCount?
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?
- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?
- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?
- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?
- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?
- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?
- MEASUrement:MEAS<x>:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:GATing:LOGICSource?
- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?
- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
- MEASUrement:MEAS<x>:GATing:SEARCHSource?
- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?
- MEASUrement:MEAS<x>:GATing?
- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?
- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?
- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?
- MEASUrement:MEAS<x>:LABel <QString>
- MEASUrement:MEAS<x>:LABel?
- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?
- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?
- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?
- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?
- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?
- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?
- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
- MEASUrement:MEAS<x>:PERFREQ:EDGE?
- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?
- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?
- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?
- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?
- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?
- MEASUrement:MEAS<x>:SOUrce1 {CH<x>|DCH<x>_D<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOUrce1?
- MEASUrement:MEAS<x>:STATUS?
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?
- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?
- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:TRANSition?
- MEASUrement:MEAS<x>:TYPe {ACRMS|AMPlITUDE|AREA|BASE|BURSTWIDTH|DATARATE|DELAY|FALLSLEWRATE|FALLTIME|FREQUENCY|HIGHTIME|HOLD|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NOVERSHOOT|NWIDTH|PDUTY|PERIOD|PHASE|PK2Pk|POVERSHOOT|PWIDTH|RISESLEWRATE|RISETIME|RMS|SETUP|SKEW|TIMEOUTSIDELEVEL|TOP}
- MEASUrement:MEAS<x>:TYPe?
- MEASUrement:MEAS<x>:XUNIT?
- MEASUrement:MEAS<x>:YUNIT?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:REF<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REF<x>:REFLevels:BASETop?
- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?
- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?
- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?
- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?
- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?
- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?
- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?
- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?
- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?
- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?
- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?
- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?
- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?
- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?
- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?
- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?
- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?
- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?
- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?
- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?
- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?
- MEASUrement?

Measurement ¶

Bases: SCPICmdRead

The MEASUrement command.

Description

This query-only command returns all measurement parameters.

Usage

Using the .query() method will send the MEASUrement? query.
Using the .verify(value) method will send the MEASUrement? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement?

Properties

.addmeas: The MEASUrement:ADDMEAS command.
.addnew: The MEASUrement:ADDNew command.
.annotate: The MEASUrement:ANNOTate command.
.ch: The MEASUrement:CH<x> command tree.
.deleteall: The MEASUrement:DELETEALL command.
.delete: The MEASUrement:DELete command.
.edge: The MEASUrement:EDGE<x> command.
.gating: The MEASUrement:GATing command.
.interp: The MEASUrement:INTERp command.
.list: The MEASUrement:LIST command.
.math: The MEASUrement:MATH<x> command tree.
.meas: The MEASUrement:MEAS<x> command tree.
.ref: The MEASUrement:REF<x> command tree.
.reflevels: The MEASUrement:REFLevels command tree.
.statistics: The MEASUrement:STATIstics command tree.

addmeas `property` ¶

addmeas: MeasurementAddmeas

Return the MEASUrement:ADDMEAS command.

Description

This command adds a measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDMEAS value command.

SCPI Syntax

- MEASUrement:ADDMEAS {ACRMS|AMPlITUDE|AREA|BASE|BURSTWIDTH|DATARATE|DELAY|FALLSLEWRATE|FALLTIME|FREQUENCY|HIGHTIME|HOLD|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NWIDTTH|PDUTY|PERIOD|PHASE|PK2Pk|POVERSHOOT|PWIDTH|RISESLEWRATE|RISETIME|RMS|SETUP|SKEW|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TOP}

Info

ACRMS (AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIdth (Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SETUP (Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.
SKEW Skew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.
TIMETOMAX Time to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.
TIMETOMIN Time to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.

addnew `property` ¶

addnew: MeasurementAddnew

Return the MEASUrement:ADDNew command.

Description

This command adds the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDNew value command.

SCPI Syntax

- MEASUrement:ADDNew 'QString'

Info

'QString' is the measurement to add. The argument is of the form ‘MEAS’ where NR1 ≥ 1.

annotate `property` ¶

annotate: MeasurementAnnotate

Return the MEASUrement:ANNOTate command.

Description

This command sets or queries the annotation state for measurements.

Usage

Using the .query() method will send the MEASUrement:ANNOTate? query.
Using the .verify(value) method will send the MEASUrement:ANNOTate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:ANNOTate value command.

SCPI Syntax

- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?

Info

OFF turns off measurement annotations.
AUTO turns on visible measurement annotations.

ch `property` ¶

ch: dict[int, MeasurementChannel]

Return the MEASUrement:CH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>? query.
Using the .verify(value) method will send the MEASUrement:CH<x>? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.reflevels: The MEASUrement:CH<x>:REFLevels command tree.

delete `property` ¶

delete: MeasurementDelete

Return the MEASUrement:DELete command.

Description

The command deletes the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:DELete value command.

SCPI Syntax

- MEASUrement:DELete <QString>

Info

<QString> is the measurement to delete. Argument is of the form ‘MEAS’ where is ≥1.

deleteall `property` ¶

deleteall: MeasurementDeleteall

Return the MEASUrement:DELETEALL command.

Description

This command deletes all the active instances of measurements defined in the scope application.

Usage

Using the .write() method will send the MEASUrement:DELETEALL command.

SCPI Syntax

- MEASUrement:DELETEALL

edge `property` ¶

edge: dict[int, MeasurementEdgeItem]

Return the MEASUrement:EDGE<x> command.

Description

This command sets or queries the type of the edge for the measurement.

Usage

Using the .query() method will send the MEASUrement:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:EDGE<x> value command.

SCPI Syntax

- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:EDGE<x>?

Info

FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.

gating `property` ¶

gating: MeasurementGating

Return the MEASUrement:GATing command.

Description

This command sets or queries the global gating type for the measurement.

Usage

Using the .query() method will send the MEASUrement:GATing? query.
Using the .verify(value) method will send the MEASUrement:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing value command.

SCPI Syntax

- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing?

Info

NONE turns off measurement gating.
SCREen turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only on the portion of the waveform where the logic source is in the active state.
SEARCH specifies that measurements are taken based on search criteria.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Sub-properties

.active: The MEASUrement:GATing:ACTive command.
.endtime: The MEASUrement:GATing:ENDtime command.
.hysteresis: The MEASUrement:GATing:HYSTeresis command.
.logicsource: The MEASUrement:GATing:LOGICSource command.
.midref: The MEASUrement:GATing:MIDRef command.
.searchsource: The MEASUrement:GATing:SEARCHSource command.
.starttime: The MEASUrement:GATing:STARTtime command.

interp `property` ¶

interp: MeasurementInterp

Return the MEASUrement:INTERp command.

Description

This command sets or queries the interpolation mode used to locate edge crossings.

Usage

Using the .query() method will send the MEASUrement:INTERp? query.
Using the .verify(value) method will send the MEASUrement:INTERp? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:INTERp value command.

SCPI Syntax

- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?

Info

AUTO automatically selects the interpolation mode.
SINX specifies sin(x)/x interpolation, where acquired points are fit to a curve.
LINear specifies linear interpolation, where acquired points are connected with straight lines.

list `property` ¶

list: MeasurementList

Return the MEASUrement:LIST command.

Description

This query returns a comma separated list of all currently defined measurements.

Usage

Using the .query() method will send the MEASUrement:LIST? query.
Using the .verify(value) method will send the MEASUrement:LIST? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:LIST?

math `property` ¶

math: dict[int, MeasurementMathItem]

Return the MEASUrement:MATH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.reflevels: The MEASUrement:MATH<x>:REFLevels command tree.

meas `property` ¶

meas: dict[int, MeasurementMeasItem]

Return the MEASUrement:MEAS<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.burstedgtype: The MEASUrement:MEAS<x>:BURSTEDGTYPe command.
.ccresults: The MEASUrement:MEAS<x>:CCRESUlts command tree.
.delay: The MEASUrement:MEAS<x>:DELay command tree.
.displaystat: The MEASUrement:MEAS<x>:DISPlaystat command tree.
.edge: The MEASUrement:MEAS<x>:EDGE<x> command.
.edgeincre: The MEASUrement:MEAS<x>:EDGEIncre command.
.edges: The MEASUrement:MEAS<x>:EDGES command tree.
.failcount: The MEASUrement:MEAS<x>:FAILCount command.
.fromedgesearchdirect: The MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.
.fromedge: The MEASUrement:MEAS<x>:FROMedge command.
.gating: The MEASUrement:MEAS<x>:GATing command.
.globalref: The MEASUrement:MEAS<x>:GLOBalref command.
.highrefvoltage: The MEASUrement:MEAS<x>:HIGHREFVoltage command.
.idletime: The MEASUrement:MEAS<x>:IDLETime command.
.label: The MEASUrement:MEAS<x>:LABel command.
.lowrefvoltage: The MEASUrement:MEAS<x>:LOWREFVoltage command.
.passfailenabled: The MEASUrement:MEAS<x>:PASSFAILENabled command.
.passfailhighlimit: The MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.
.passfaillimit: The MEASUrement:MEAS<x>:PASSFAILLIMit command.
.passfaillowlimit: The MEASUrement:MEAS<x>:PASSFAILLOWlimit command.
.passfailmargin: The MEASUrement:MEAS<x>:PASSFAILMARgin command.
.passfailwhen: The MEASUrement:MEAS<x>:PASSFAILWHEN command.
.perfreq: The MEASUrement:MEAS<x>:PERFREQ command tree.
.polarity: The MEASUrement:MEAS<x>:POLarity command.
.reflevels: The MEASUrement:MEAS<x>:REFLevels command tree.
.reflevels1: The MEASUrement:MEAS<x>:REFLevels1 command tree.
.refmode: The MEASUrement:MEAS<x>:REFMode command.
.refvoltage: The MEASUrement:MEAS<x>:REFVoltage command.
.results: The MEASUrement:MEAS<x>:RESUlts command tree.
.signaltype: The MEASUrement:MEAS<x>:SIGNALType command.
.source1: The MEASUrement:MEAS<x>:SOUrce1 command.
.status: The MEASUrement:MEAS<x>:STATUS command.
.toedgesearchdirect: The MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.
.toedge: The MEASUrement:MEAS<x>:TOEdge command.
.transition: The MEASUrement:MEAS<x>:TRANSition command.
.type: The MEASUrement:MEAS<x>:TYPe command.
.xunit: The MEASUrement:MEAS<x>:XUNIT command.
.yunit: The MEASUrement:MEAS<x>:YUNIT command.

ref `property` ¶

ref: dict[int, MeasurementRefItem]

Return the MEASUrement:REF<x> command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>? query.
Using the .verify(value) method will send the MEASUrement:REF<x>? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.reflevels: The MEASUrement:REF<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementReflevels

Return the MEASUrement:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REFLevels? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.absolute: The MEASUrement:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REFLevels:BASETop command.
.method: The MEASUrement:REFLevels:METHod command.
.mode: The MEASUrement:REFLevels:MODE command.
.percent: The MEASUrement:REFLevels:PERCent command tree.
.type: The MEASUrement:REFLevels:TYPE command.

statistics `property` ¶

statistics: MeasurementStatistics

Return the MEASUrement:STATIstics command tree.

Usage

Using the .query() method will send the MEASUrement:STATIstics? query.
Using the .verify(value) method will send the MEASUrement:STATIstics? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.cyclemode: The MEASUrement:STATIstics:CYCLEMode command.

MeasurementAddmeas ¶

Bases: SCPICmdWrite

The MEASUrement:ADDMEAS command.

Description

This command adds a measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDMEAS value command.

SCPI Syntax

- MEASUrement:ADDMEAS {ACRMS|AMPlITUDE|AREA|BASE|BURSTWIDTH|DATARATE|DELAY|FALLSLEWRATE|FALLTIME|FREQUENCY|HIGHTIME|HOLD|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NWIDTTH|PDUTY|PERIOD|PHASE|PK2Pk|POVERSHOOT|PWIDTH|RISESLEWRATE|RISETIME|RMS|SETUP|SKEW|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TOP}

Info

ACRMS (AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIdth (Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SETUP (Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.
SKEW Skew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.
TIMETOMAX Time to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.
TIMETOMIN Time to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.

MeasurementAddnew ¶

Bases: SCPICmdWrite

The MEASUrement:ADDNew command.

Description

This command adds the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDNew value command.

SCPI Syntax

- MEASUrement:ADDNew 'QString'

Info

'QString' is the measurement to add. The argument is of the form ‘MEAS’ where NR1 ≥ 1.

MeasurementAnnotate ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:ANNOTate command.

Description

This command sets or queries the annotation state for measurements.

Usage

Using the .query() method will send the MEASUrement:ANNOTate? query.
Using the .verify(value) method will send the MEASUrement:ANNOTate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:ANNOTate value command.

SCPI Syntax

- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?

Info

OFF turns off measurement annotations.
AUTO turns on visible measurement annotations.

MeasurementChannel ¶

Bases: ValidatedChannel, SCPICmdRead

The MEASUrement:CH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>? query.
Using the .verify(value) method will send the MEASUrement:CH<x>? query and raise an AssertionError if the returned value does not match value.

Properties

.reflevels: The MEASUrement:CH<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementChannelReflevels

Return the MEASUrement:CH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.absolute: The MEASUrement:CH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:CH<x>:REFLevels:BASETop command.
.method: The MEASUrement:CH<x>:REFLevels:METHod command.
.percent: The MEASUrement:CH<x>:REFLevels:PERCent command tree.

MeasurementChannelReflevels ¶

Bases: SCPICmdRead

The MEASUrement:CH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Properties

.absolute: The MEASUrement:CH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:CH<x>:REFLevels:BASETop command.
.method: The MEASUrement:CH<x>:REFLevels:METHod command.
.percent: The MEASUrement:CH<x>:REFLevels:PERCent command tree.

absolute `property` ¶

absolute: MeasurementChannelReflevelsAbsolute

Return the MEASUrement:CH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementChannelReflevelsBasetop

Return the MEASUrement:CH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.

method `property` ¶

method: MeasurementChannelReflevelsMethod

Return the MEASUrement:CH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?

Info

PERCent specifies percent reference level units.
ABSolute specifies absolute reference level units.

percent `property` ¶

percent: MeasurementChannelReflevelsPercent

Return the MEASUrement:CH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

MeasurementChannelReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementChannelReflevelsAbsoluteFallhigh

Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

falllow `property` ¶

falllow: MeasurementChannelReflevelsAbsoluteFalllow

Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

fallmid `property` ¶

fallmid: MeasurementChannelReflevelsAbsoluteFallmid

Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the mid reference level used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

hysteresis `property` ¶

hysteresis: MeasurementChannelReflevelsAbsoluteHysteresis

Return the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the hysteresis value used for autoset.

risehigh `property` ¶

risehigh: MeasurementChannelReflevelsAbsoluteRisehigh

Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the high reference level of the rising edge when the source ref level method is set to absolute.

riselow `property` ¶

riselow: MeasurementChannelReflevelsAbsoluteRiselow

Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the low reference level of the rising edge when the source ref level method is set to absolute.

risemid `property` ¶

risemid: MeasurementChannelReflevelsAbsoluteRisemid

Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge when the source ref level method is set to absolute.

type `property` ¶

type: MeasurementChannelReflevelsAbsoluteType

Return the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the source. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute reference levels for the specified measurement channel are the same.
UNIQue specifies that the absolute reference levels for the specified measurement channel are not the same.

MeasurementChannelReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementChannelReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementChannelReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the mid reference level used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

MeasurementChannelReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the hysteresis value used for autoset.

MeasurementChannelReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the high reference level of the rising edge when the source ref level method is set to absolute.

MeasurementChannelReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the low reference level of the rising edge when the source ref level method is set to absolute.

MeasurementChannelReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge when the source ref level method is set to absolute.

MeasurementChannelReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the source. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute reference levels for the specified measurement channel are the same.
UNIQue specifies that the absolute reference levels for the specified measurement channel are not the same.

MeasurementChannelReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.

MeasurementChannelReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?

Info

PERCent specifies percent reference level units.
ABSolute specifies absolute reference level units.

MeasurementChannelReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementChannelReflevelsPercentFallhigh

Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

falllow `property` ¶

falllow: MeasurementChannelReflevelsPercentFalllow

Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the low reference level when the measurement Ref level method is set to Percent.

fallmid `property` ¶

fallmid: MeasurementChannelReflevelsPercentFallmid

Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

hysteresis `property` ¶

hysteresis: MeasurementChannelReflevelsPercentHysteresis

Return the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementChannelReflevelsPercentRisehigh

Return the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

riselow `property` ¶

riselow: MeasurementChannelReflevelsPercentRiselow

Return the MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

risemid `property` ¶

risemid: MeasurementChannelReflevelsPercentRisemid

Return the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

type `property` ¶

type: MeasurementChannelReflevelsPercentType

Return the MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?

Info

TENNinety specifies reference levels at the 10 and 90% levels.
TWENtyeighty specifies reference levels at the 20 and 80% levels.
CUSTom specifies custom reference levels.

MeasurementChannelReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the low reference level when the measurement Ref level method is set to Percent.

MeasurementChannelReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the hysteresis value used for the autoset.

MeasurementChannelReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?

Info

TENNinety specifies reference levels at the 10 and 90% levels.
TWENtyeighty specifies reference levels at the 20 and 80% levels.
CUSTom specifies custom reference levels.

MeasurementDelete ¶

Bases: SCPICmdWrite

The MEASUrement:DELete command.

Description

The command deletes the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:DELete value command.

SCPI Syntax

- MEASUrement:DELete <QString>

Info

<QString> is the measurement to delete. Argument is of the form ‘MEAS’ where is ≥1.

MeasurementDeleteall ¶

Bases: SCPICmdWriteNoArguments

The MEASUrement:DELETEALL command.

Description

This command deletes all the active instances of measurements defined in the scope application.

Usage

Using the .write() method will send the MEASUrement:DELETEALL command.

SCPI Syntax

- MEASUrement:DELETEALL

MeasurementEdgeItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:EDGE<x> command.

Description

This command sets or queries the type of the edge for the measurement.

Usage

Using the .query() method will send the MEASUrement:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:EDGE<x> value command.

SCPI Syntax

- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:EDGE<x>?

Info

FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.

MeasurementGating ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing command.

Description

This command sets or queries the global gating type for the measurement.

Usage

Using the .query() method will send the MEASUrement:GATing? query.
Using the .verify(value) method will send the MEASUrement:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing value command.

SCPI Syntax

- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing?

Info

NONE turns off measurement gating.
SCREen turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only on the portion of the waveform where the logic source is in the active state.
SEARCH specifies that measurements are taken based on search criteria.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Properties

.active: The MEASUrement:GATing:ACTive command.
.endtime: The MEASUrement:GATing:ENDtime command.
.hysteresis: The MEASUrement:GATing:HYSTeresis command.
.logicsource: The MEASUrement:GATing:LOGICSource command.
.midref: The MEASUrement:GATing:MIDRef command.
.searchsource: The MEASUrement:GATing:SEARCHSource command.
.starttime: The MEASUrement:GATing:STARTtime command.

active `property` ¶

active: MeasurementGatingActive

Return the MEASUrement:GATing:ACTive command.

Description

This command sets or queries the global gating active level used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?

Info

HIGH specifies the gate is HIGH.
LOW specifies the gate is LOW.

endtime `property` ¶

endtime: MeasurementGatingEndtime

Return the MEASUrement:GATing:ENDtime command.

Description

Sets or queries the end gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?

Info

<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

hysteresis `property` ¶

hysteresis: MeasurementGatingHysteresis

Return the MEASUrement:GATing:HYSTeresis command.

Description

This command sets or queries the global gating hysteresis value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?

Info

<NR3> is the gating hysteresis.

logicsource `property` ¶

logicsource: MeasurementGatingLogicsource

Return the MEASUrement:GATing:LOGICSource command.

Description

This command sets or queries the gating data source used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:LOGICSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:LOGICSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

midref `property` ¶

midref: MeasurementGatingMidref

Return the MEASUrement:GATing:MIDRef command.

Description

This command sets or queries the global gating mid ref value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?

Info

<NR3> is the mid ref value for gating.

searchsource `property` ¶

searchsource: MeasurementGatingSearchsource

Return the MEASUrement:GATing:SEARCHSource command.

Description

This command sets or queries the global gating search source when the gating type is search.

Usage

Using the .query() method will send the MEASUrement:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:GATing:SEARCHSource SEARCH<x>
- MEASUrement:GATing:SEARCHSource?

Info

SEARCH<x> is the search source.

starttime `property` ¶

starttime: MeasurementGatingStarttime

Return the MEASUrement:GATing:STARTtime command.

Description

Sets or queries the start gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?

Info

<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementGatingActive ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:ACTive command.

Description

This command sets or queries the global gating active level used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?

Info

HIGH specifies the gate is HIGH.
LOW specifies the gate is LOW.

MeasurementGatingEndtime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:ENDtime command.

Description

Sets or queries the end gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?

Info

<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementGatingHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:HYSTeresis command.

Description

This command sets or queries the global gating hysteresis value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?

Info

<NR3> is the gating hysteresis.

MeasurementGatingLogicsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:LOGICSource command.

Description

This command sets or queries the gating data source used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:LOGICSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:LOGICSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementGatingMidref ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:MIDRef command.

Description

This command sets or queries the global gating mid ref value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?

Info

<NR3> is the mid ref value for gating.

MeasurementGatingSearchsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:SEARCHSource command.

Description

This command sets or queries the global gating search source when the gating type is search.

Usage

Using the .query() method will send the MEASUrement:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:GATing:SEARCHSource SEARCH<x>
- MEASUrement:GATing:SEARCHSource?

Info

SEARCH<x> is the search source.

MeasurementGatingStarttime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:STARTtime command.

Description

Sets or queries the start gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?

Info

<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementInterp ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:INTERp command.

Description

This command sets or queries the interpolation mode used to locate edge crossings.

Usage

Using the .query() method will send the MEASUrement:INTERp? query.
Using the .verify(value) method will send the MEASUrement:INTERp? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:INTERp value command.

SCPI Syntax

- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?

Info

AUTO automatically selects the interpolation mode.
SINX specifies sin(x)/x interpolation, where acquired points are fit to a curve.
LINear specifies linear interpolation, where acquired points are connected with straight lines.

MeasurementList ¶

Bases: SCPICmdRead

The MEASUrement:LIST command.

Description

This query returns a comma separated list of all currently defined measurements.

Usage

Using the .query() method will send the MEASUrement:LIST? query.
Using the .verify(value) method will send the MEASUrement:LIST? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:LIST?

MeasurementMathItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The MEASUrement:MATH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.reflevels: The MEASUrement:MATH<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementMathItemReflevels

Return the MEASUrement:MATH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.absolute: The MEASUrement:MATH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:MATH<x>:REFLevels:BASETop command.
.method: The MEASUrement:MATH<x>:REFLevels:METHod command.
.percent: The MEASUrement:MATH<x>:REFLevels:PERCent command tree.

MeasurementMathItemReflevels ¶

Bases: SCPICmdRead

The MEASUrement:MATH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.absolute: The MEASUrement:MATH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:MATH<x>:REFLevels:BASETop command.
.method: The MEASUrement:MATH<x>:REFLevels:METHod command.
.percent: The MEASUrement:MATH<x>:REFLevels:PERCent command tree.

absolute `property` ¶

absolute: MeasurementMathItemReflevelsAbsolute

Return the MEASUrement:MATH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementMathItemReflevelsBasetop

Return the MEASUrement:MATH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?

Info

MATH<x> specifies the math number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

method `property` ¶

method: MeasurementMathItemReflevelsMethod

Return the MEASUrement:MATH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?

Info

MATH<x> specifies the math number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MATH<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MATH<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

percent `property` ¶

percent: MeasurementMathItemReflevelsPercent

Return the MEASUrement:MATH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

MeasurementMathItemReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementMathItemReflevelsAbsoluteFallhigh

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

falllow `property` ¶

falllow: MeasurementMathItemReflevelsAbsoluteFalllow

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

fallmid `property` ¶

fallmid: MeasurementMathItemReflevelsAbsoluteFallmid

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

hysteresis `property` ¶

hysteresis: MeasurementMathItemReflevelsAbsoluteHysteresis

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementMathItemReflevelsAbsoluteRisehigh

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

riselow `property` ¶

riselow: MeasurementMathItemReflevelsAbsoluteRiselow

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

risemid `property` ¶

risemid: MeasurementMathItemReflevelsAbsoluteRisemid

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Absolute.

type `property` ¶

type: MeasurementMathItemReflevelsAbsoluteType

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?

Info

MATH<x> specifies the math number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMathItemReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

MeasurementMathItemReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

MeasurementMathItemReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Absolute.

MeasurementMathItemReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?

Info

MATH<x> specifies the math number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMathItemReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?

Info

MATH<x> specifies the math number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

MeasurementMathItemReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?

Info

MATH<x> specifies the math number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MATH<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MATH<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementMathItemReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementMathItemReflevelsPercentFallhigh

Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level when the measurement Ref level method is set to Percent.

falllow `property` ¶

falllow: MeasurementMathItemReflevelsPercentFalllow

Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

fallmid `property` ¶

fallmid: MeasurementMathItemReflevelsPercentFallmid

Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

hysteresis `property` ¶

hysteresis: MeasurementMathItemReflevelsPercentHysteresis

Return the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementMathItemReflevelsPercentRisehigh

Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

riselow `property` ¶

riselow: MeasurementMathItemReflevelsPercentRiselow

Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

risemid `property` ¶

risemid: MeasurementMathItemReflevelsPercentRisemid

Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

type `property` ¶

type: MeasurementMathItemReflevelsPercentType

Return the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?

Info

MATH<x> specifies the math number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMathItemReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

MeasurementMathItemReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?

Info

MATH<x> specifies the math number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMeasItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The MEASUrement:MEAS<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.burstedgtype: The MEASUrement:MEAS<x>:BURSTEDGTYPe command.
.ccresults: The MEASUrement:MEAS<x>:CCRESUlts command tree.
.delay: The MEASUrement:MEAS<x>:DELay command tree.
.displaystat: The MEASUrement:MEAS<x>:DISPlaystat command tree.
.edge: The MEASUrement:MEAS<x>:EDGE<x> command.
.edgeincre: The MEASUrement:MEAS<x>:EDGEIncre command.
.edges: The MEASUrement:MEAS<x>:EDGES command tree.
.failcount: The MEASUrement:MEAS<x>:FAILCount command.
.fromedgesearchdirect: The MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.
.fromedge: The MEASUrement:MEAS<x>:FROMedge command.
.gating: The MEASUrement:MEAS<x>:GATing command.
.globalref: The MEASUrement:MEAS<x>:GLOBalref command.
.highrefvoltage: The MEASUrement:MEAS<x>:HIGHREFVoltage command.
.idletime: The MEASUrement:MEAS<x>:IDLETime command.
.label: The MEASUrement:MEAS<x>:LABel command.
.lowrefvoltage: The MEASUrement:MEAS<x>:LOWREFVoltage command.
.passfailenabled: The MEASUrement:MEAS<x>:PASSFAILENabled command.
.passfailhighlimit: The MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.
.passfaillimit: The MEASUrement:MEAS<x>:PASSFAILLIMit command.
.passfaillowlimit: The MEASUrement:MEAS<x>:PASSFAILLOWlimit command.
.passfailmargin: The MEASUrement:MEAS<x>:PASSFAILMARgin command.
.passfailwhen: The MEASUrement:MEAS<x>:PASSFAILWHEN command.
.perfreq: The MEASUrement:MEAS<x>:PERFREQ command tree.
.polarity: The MEASUrement:MEAS<x>:POLarity command.
.reflevels: The MEASUrement:MEAS<x>:REFLevels command tree.
.reflevels1: The MEASUrement:MEAS<x>:REFLevels1 command tree.
.refmode: The MEASUrement:MEAS<x>:REFMode command.
.refvoltage: The MEASUrement:MEAS<x>:REFVoltage command.
.results: The MEASUrement:MEAS<x>:RESUlts command tree.
.signaltype: The MEASUrement:MEAS<x>:SIGNALType command.
.source1: The MEASUrement:MEAS<x>:SOUrce1 command.
.status: The MEASUrement:MEAS<x>:STATUS command.
.toedgesearchdirect: The MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.
.toedge: The MEASUrement:MEAS<x>:TOEdge command.
.transition: The MEASUrement:MEAS<x>:TRANSition command.
.type: The MEASUrement:MEAS<x>:TYPe command.
.xunit: The MEASUrement:MEAS<x>:XUNIT command.
.yunit: The MEASUrement:MEAS<x>:YUNIT command.

burstedgtype `property` ¶

burstedgtype: MeasurementMeasItemBurstedgtype

Return the MEASUrement:MEAS<x>:BURSTEDGTYPe command.

Description

This command sets or queries the burst edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?

Info

MEAS<x> specifies the measurement number.
RISE specifies a burst with a rising edge.
FALL specifies a burst with a falling edge.

ccresults `property` ¶

ccresults: MeasurementMeasItemCcresults

Return the MEASUrement:MEAS<x>:CCRESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.allacqs: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

delay `property` ¶

delay: MeasurementMeasItemDelay

Return the MEASUrement:MEAS<x>:DELay command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.edge: The MEASUrement:MEAS<x>:DELay:EDGE<x> command.

displaystat `property` ¶

displaystat: MeasurementMeasItemDisplaystat

Return the MEASUrement:MEAS<x>:DISPlaystat command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.enable: The MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

edge `property` ¶

edge: dict[int, MeasurementMeasItemEdgeItem]

Return the MEASUrement:MEAS<x>:EDGE<x> command.

Description

This command sets or queries the type of the specified edge, rise or fall, for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:MEAS<x>:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
EDGE<x> specifies the edge number.
RISE specifies the rising edge.
FALL specifies the falling edge.
BOTH specifies either the rising or falling edge.

edgeincre `property` ¶

edgeincre: MeasurementMeasItemEdgeincre

Return the MEASUrement:MEAS<x>:EDGEIncre command.

Description

This command sets or queries the edge increment value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEIncre? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEIncre? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEIncre value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?

Info

MEAS<x> specifies the measurement number.
<NR3> is the measurements edge increment value.

edges `property` ¶

edges: MeasurementMeasItemEdges

Return the MEASUrement:MEAS<x>:EDGES command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.fromlevel: The MEASUrement:MEAS<x>:EDGES:FROMLevel command.
.level: The MEASUrement:MEAS<x>:EDGES:LEVel command.
.n: The MEASUrement:MEAS<x>:EDGES:N command.
.slewratemethod: The MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.
.tolevel: The MEASUrement:MEAS<x>:EDGES:TOLevel command.

failcount `property` ¶

failcount: MeasurementMeasItemFailcount

Return the MEASUrement:MEAS<x>:FAILCount command.

Description

This command returns the number of measurement failures, if applicable, for the selected measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FAILCount? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FAILCount? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:FAILCount?

fromedge `property` ¶

fromedge: MeasurementMeasItemFromedge

Return the MEASUrement:MEAS<x>:FROMedge command.

Description

This command sets or queries the from edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMedge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMedge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMedge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both the rising and falling edges of the waveform.

fromedgesearchdirect `property` ¶

fromedgesearchdirect: MeasurementMeasItemFromedgesearchdirect

Return the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.

Description

This command sets or queries the from edge search direction for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search from the edge.
BACKWard specifies a backward search from the edge.

gating `property` ¶

gating: MeasurementMeasItemGating

Return the MEASUrement:MEAS<x>:GATing command.

Description

This command sets or queries the gating type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing?

Info

MEAS<x> is the measurement number for which to return a value.
NONE specifies measurements are taken across the entire record.
SCREEN turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only when the logical state of other waveforms is true.
SEARch specifies that measurements are taken only where the results of a user specified search are found.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Sub-properties

.active: The MEASUrement:MEAS<x>:GATing:ACTive command.
.endtime: The MEASUrement:MEAS<x>:GATing:ENDtime command.
.global: The MEASUrement:MEAS<x>:GATing:GLOBal command.
.hysteresis: The MEASUrement:MEAS<x>:GATing:HYSTeresis command.
.logicsource: The MEASUrement:MEAS<x>:GATing:LOGICSource command.
.midref: The MEASUrement:MEAS<x>:GATing:MIDRef command.
.searchsource: The MEASUrement:MEAS<x>:GATing:SEARCHSource command.
.starttime: The MEASUrement:MEAS<x>:GATing:STARTtime command.

globalref `property` ¶

globalref: MeasurementMeasItemGlobalref

Return the MEASUrement:MEAS<x>:GLOBalref command.

Description

This command sets or queries the reference levels global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GLOBalref? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GLOBalref? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GLOBalref value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?

Info

MEAS<x> specifies the measurement number.
OFF allows ref levels to be set separately for each measurement.
ON applies the same ref levels to all measurements.
0 allows ref levels to be set separately for each measurement.
1 applies the same ref levels to all measurements.

highrefvoltage `property` ¶

highrefvoltage: MeasurementMeasItemHighrefvoltage

Return the MEASUrement:MEAS<x>:HIGHREFVoltage command.

Description

This command sets or queries the high reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference voltage value for the selected configuration.

idletime `property` ¶

idletime: MeasurementMeasItemIdletime

Return the MEASUrement:MEAS<x>:IDLETime command.

Description

This command sets or queries the idle time for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:IDLETime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:IDLETime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:IDLETime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the idle time.

label `property` ¶

label: MeasurementMeasItemLabel

Return the MEASUrement:MEAS<x>:LABel command.

Description

This command sets or queries the label for the measurement. As the label can contain non 7-bit ASCII text, it is stored in Percent Encoding format. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LABel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LABel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LABel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LABel <QString>
- MEASUrement:MEAS<x>:LABel?

Info

MEAS<x> specifies the measurement number.
<QString> is the measurement label.

lowrefvoltage `property` ¶

lowrefvoltage: MeasurementMeasItemLowrefvoltage

Return the MEASUrement:MEAS<x>:LOWREFVoltage command.

Description

This command sets or queries the low reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference voltage value for the selected configuration.

passfailenabled `property` ¶

passfailenabled: MeasurementMeasItemPassfailenabled

Return the MEASUrement:MEAS<x>:PASSFAILENabled command.

Description

This command returns or sets the pass/fail test enable status. If enabled, this will turn on pass fail testing for the specified measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?

Info

<NR1> enables or disables pass fail testing for the specified measurement. A value of 1 enables and a value of 0 disables.

passfailhighlimit `property` ¶

passfailhighlimit: MeasurementMeasItemPassfailhighlimit

Return the MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.

Description

This command returns or sets the high limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?

Info

<NR2> sets the high limit for a measurement test. The high limit is a number which a measurement result will be tested against.

passfaillimit `property` ¶

passfaillimit: MeasurementMeasItemPassfaillimit

Return the MEASUrement:MEAS<x>:PASSFAILLIMit command.

Description

This command returns or sets the limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?

Info

<NR2> sets the limit for a measurement test. The limit is a number which a measurement result will be tested against.

passfaillowlimit `property` ¶

passfaillowlimit: MeasurementMeasItemPassfaillowlimit

Return the MEASUrement:MEAS<x>:PASSFAILLOWlimit command.

Description

This command returns or sets the low limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?

Info

<NR2> sets the low limit for a measurement test. The limit is a number which a measurement result will be tested against.

passfailmargin `property` ¶

passfailmargin: MeasurementMeasItemPassfailmargin

Return the MEASUrement:MEAS<x>:PASSFAILMARgin command.

Description

This command returns or sets the allowed margin for limit comparisons for all pass/fail checks. This is given as a percentage with a default value of 0.05 representing 5%. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?

Info

<NR2> sets the allowed margin for limit comparisons for all pass/fail checks. The margin as a percentage of the limit.

passfailwhen `property` ¶

passfailwhen: MeasurementMeasItemPassfailwhen

Return the MEASUrement:MEAS<x>:PASSFAILWHEN command.

Description

This command sets or returns the condition on which a measurement test fails. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?

Info

LESSthan sets the condition for measurement test failure as less than the given limit. This is the default value.
GREATERthan sets the condition for measurement test failure as greater than the given limit.
Equals sets the condition for measurement test failure as equals the given limit.
NOTEQuals sets the condition for measurement test failure as not equal to the given limit.
INSIDErange sets the condition for measurement test failure as inside the limit range.
OUTSIDErange sets the condition for measurement test failure as outside the limit range.

perfreq `property` ¶

perfreq: MeasurementMeasItemPerfreq

Return the MEASUrement:MEAS<x>:PERFREQ command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.edge: The MEASUrement:MEAS<x>:PERFREQ:EDGE command.

polarity `property` ¶

polarity: MeasurementMeasItemPolarity

Return the MEASUrement:MEAS<x>:POLarity command.

Description

This command sets or queries the polarity for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POLarity? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POLarity value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?

Info

MEAS<x> specifies the measurement number.
NORMal specifies normal polarity.
INVerted specifies inverted polarity.

reflevels `property` ¶

reflevels: MeasurementMeasItemReflevels

Return the MEASUrement:MEAS<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.absolute: The MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

reflevels1 `property` ¶

reflevels1: MeasurementMeasItemReflevels1

Return the MEASUrement:MEAS<x>:REFLevels1 command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.absolute: The MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.
.basetop: The MEASUrement:MEAS<x>:REFLevels1:BASETop command.
.method: The MEASUrement:MEAS<x>:REFLevels1:METHod command.
.percent: The MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

refmode `property` ¶

refmode: MeasurementMeasItemRefmode

Return the MEASUrement:MEAS<x>:REFMode command.

Description

This command sets or queries the reference level mode for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFMode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?

Info

MEAS<x> specifies the measurement number.
AUTO sets the reference level for the measurement automatically.
MANual allows the user to set the reference level for the measurement.

refvoltage `property` ¶

refvoltage: MeasurementMeasItemRefvoltage

Return the MEASUrement:MEAS<x>:REFVoltage command.

Description

This command sets or queries the reference voltage value for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?

Info

MEAS<x> is the measurement number.
<NR3> is the reference voltage value for the selected configuration.

results `property` ¶

results: MeasurementMeasItemResults

Return the MEASUrement:MEAS<x>:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.allacqs: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.

signaltype `property` ¶

signaltype: MeasurementMeasItemSignaltype

Return the MEASUrement:MEAS<x>:SIGNALType command.

Description

This command sets or queries the signal type of source 1 for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SIGNALType? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SIGNALType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SIGNALType value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?

Info

MEAS<x> specifies the measurement number.
CLOCK specifies a clock signal type.
DATA specifies a data signal type.
AUTO automatically selects the signal type.

source1 `property` ¶

source1: MeasurementMeasItemSource1

Return the MEASUrement:MEAS<x>:SOUrce1 command.

Description

This command sets or queries the measurement source. The measurement number and source are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SOUrce1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SOUrce1 value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SOUrce1 {CH<x>|DCH<x>_D<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOUrce1?

Info

MEAS<x> specifies the measurement number.
1 specifies the source number.
CH<x> specifies an analog channel to use as the source.
DCH<x>_D<x> specifies a digital channel to use as the source. The supported digital channel value is 1. The supported digital bit values are 0 to 15.
MATH<x> specifies a math waveform to use as the source.
REF<x> specifies a reference waveform to use as the source.

status `property` ¶

status: MeasurementMeasItemStatus

Return the MEASUrement:MEAS<x>:STATUS command.

Description

This command returns the pass fail status, if applicable, for the selected measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STATUS? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STATUS? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:STATUS?

Info

PASS specifies that the user specified measurement limit has not been violated.
FAIL specifies that the user specified measurement limit has been violated.

toedge `property` ¶

toedge: MeasurementMeasItemToedge

Return the MEASUrement:MEAS<x>:TOEdge command.

Description

This command sets or queries the ‘to edge’ type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEdge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEdge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEdge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

toedgesearchdirect `property` ¶

toedgesearchdirect: MeasurementMeasItemToedgesearchdirect

Return the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.

Description

This command sets or queries the to edge search direction for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search to the edge.
BACKWard specifies a backward search to the edge.

transition `property` ¶

transition: MeasurementMeasItemTransition

Return the MEASUrement:MEAS<x>:TRANSition command.

Description

This command sets or queries the transition edges flag for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TRANSition? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TRANSition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TRANSition value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:TRANSition?

Info

<NR1> = 1, the measurement is computed on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only. If it is set to 0, the measurement is computed on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
OFF computes the measurement on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
ON computes the measurement on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only.

type `property` ¶

type: MeasurementMeasItemType

Return the MEASUrement:MEAS<x>:TYPe command.

Description

This command sets or queries the measurement type for the measurement specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TYPe {ACRMS|AMPlITUDE|AREA|BASE|BURSTWIDTH|DATARATE|DELAY|FALLSLEWRATE|FALLTIME|FREQUENCY|HIGHTIME|HOLD|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NOVERSHOOT|NWIDTH|PDUTY|PERIOD|PHASE|PK2Pk|POVERSHOOT|PWIDTH|RISESLEWRATE|RISETIME|RMS|SETUP|SKEW|TIMEOUTSIDELEVEL|TOP}
- MEASUrement:MEAS<x>:TYPe?

Info

ACRMS (AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIdth (Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SETUP (Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.
SKEW Skew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.

xunit `property` ¶

xunit: MeasurementMeasItemXunit

Return the MEASUrement:MEAS<x>:XUNIT command.

Description

Returns the horizontal scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:XUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:XUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:XUNIT?

Info

MEAS<x> specifies the measurement number.

yunit `property` ¶

yunit: MeasurementMeasItemYunit

Return the MEASUrement:MEAS<x>:YUNIT command.

Description

Returns the vertical scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:YUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:YUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:YUNIT?

Info

MEAS<x> specifies the measurement number.

MeasurementMeasItemBurstedgtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BURSTEDGTYPe command.

Description

This command sets or queries the burst edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?

Info

MEAS<x> specifies the measurement number.
RISE specifies a burst with a rising edge.
FALL specifies a burst with a falling edge.

MeasurementMeasItemCcresults ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts? query and raise an AssertionError if the returned value does not match value.

Properties

.allacqs: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

allacqs `property` ¶

allacqs: MeasurementMeasItemCcresultsAllacqs

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

currentacq `property` ¶

currentacq: MeasurementMeasItemCcresultsCurrentacq

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

MeasurementMeasItemCcresultsAllacqs ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemCcresultsAllacqsMaximum

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemCcresultsAllacqsMean

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemCcresultsAllacqsMinimum

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemCcresultsAllacqsPk2pk

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?

population `property` ¶

population: MeasurementMeasItemCcresultsAllacqsPopulation

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population of all cycle-cycle statistics for the specified measurement for all acquisitions accumulated since statistics were last reset. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemCcresultsAllacqsStddev

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?

MeasurementMeasItemCcresultsAllacqsMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?

MeasurementMeasItemCcresultsAllacqsMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?

MeasurementMeasItemCcresultsAllacqsMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?

MeasurementMeasItemCcresultsAllacqsPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?

MeasurementMeasItemCcresultsAllacqsPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population of all cycle-cycle statistics for the specified measurement for all acquisitions accumulated since statistics were last reset. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?

MeasurementMeasItemCcresultsAllacqsStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?

MeasurementMeasItemCcresultsCurrentacq ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemCcresultsCurrentacqMaximum

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemCcresultsCurrentacqMean

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemCcresultsCurrentacqMinimum

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemCcresultsCurrentacqPk2pk

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?

population `property` ¶

population: MeasurementMeasItemCcresultsCurrentacqPopulation

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population of the cycle-cycle statistics for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemCcresultsCurrentacqStddev

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?

MeasurementMeasItemCcresultsCurrentacqMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?

MeasurementMeasItemCcresultsCurrentacqMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?

MeasurementMeasItemCcresultsCurrentacqMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?

MeasurementMeasItemCcresultsCurrentacqPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?

MeasurementMeasItemCcresultsCurrentacqPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population of the cycle-cycle statistics for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?

MeasurementMeasItemCcresultsCurrentacqStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?

MeasurementMeasItemDelay ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:DELay command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.edge: The MEASUrement:MEAS<x>:DELay:EDGE<x> command.

edge `property` ¶

edge: dict[int, MeasurementMeasItemDelayEdgeItem]

Return the MEASUrement:MEAS<x>:DELay:EDGE<x> command.

Description

This command sets or queries the ‘to edge’ type when EDGE is EDGE1 and the ‘from edge’ type when EDGE is EDG2, for the measurement when the measurement type is DELAY. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

MeasurementMeasItemDelayEdgeItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:DELay:EDGE<x> command.

Description

This command sets or queries the ‘to edge’ type when EDGE is EDGE1 and the ‘from edge’ type when EDGE is EDG2, for the measurement when the measurement type is DELAY. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

MeasurementMeasItemDisplaystat ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:DISPlaystat command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.enable: The MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

enable `property` ¶

enable: MeasurementMeasItemDisplaystatEnable

Return the MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

Description

This command turns on and off display of statistics in measurement badges in the user interface. This command affects only the display of statistics, basic-statistics are computed regardless of the state of this command. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?

Info

MEAS<x> specifies the measurement number.
OFF turns off the display of statistics in measurement badges.
ON turns on the display of statistics in measurement badges.
<NR1> = 0 turns off the display of statistics in the measurement badge, any other value turns on the display of statistics.

MeasurementMeasItemDisplaystatEnable ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

Description

This command turns on and off display of statistics in measurement badges in the user interface. This command affects only the display of statistics, basic-statistics are computed regardless of the state of this command. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?

Info

MEAS<x> specifies the measurement number.
OFF turns off the display of statistics in measurement badges.
ON turns on the display of statistics in measurement badges.
<NR1> = 0 turns off the display of statistics in the measurement badge, any other value turns on the display of statistics.

MeasurementMeasItemEdgeItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGE<x> command.

Description

This command sets or queries the type of the specified edge, rise or fall, for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:MEAS<x>:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
EDGE<x> specifies the edge number.
RISE specifies the rising edge.
FALL specifies the falling edge.
BOTH specifies either the rising or falling edge.

MeasurementMeasItemEdgeincre ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGEIncre command.

Description

This command sets or queries the edge increment value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEIncre? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEIncre? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEIncre value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?

Info

MEAS<x> specifies the measurement number.
<NR3> is the measurements edge increment value.

MeasurementMeasItemEdges ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:EDGES command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.fromlevel: The MEASUrement:MEAS<x>:EDGES:FROMLevel command.
.level: The MEASUrement:MEAS<x>:EDGES:LEVel command.
.n: The MEASUrement:MEAS<x>:EDGES:N command.
.slewratemethod: The MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.
.tolevel: The MEASUrement:MEAS<x>:EDGES:TOLevel command.

fromlevel `property` ¶

fromlevel: MeasurementMeasItemEdgesFromlevel

Return the MEASUrement:MEAS<x>:EDGES:FROMLevel command.

Description

This command sets or queries the ‘from level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?

Info

MEAS<x> specifies the measurement number.
MID specifies the MID level.
HIGH specifies the HIGH level.
LOW specifies the LOW level.

level `property` ¶

level: MeasurementMeasItemEdgesLevel

Return the MEASUrement:MEAS<x>:EDGES:LEVel command.

Description

This sets or queries the level type for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
LOW specifies the LOW level.
BOTH specifies both the HIGH and LOW level.

n `property` ¶

n: MeasurementMeasItemEdgesN

Return the MEASUrement:MEAS<x>:EDGES:N command.

Description

The command sets or queries the number of accumulation cycles for the measurement when the measurement type is nperiod. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?

Info

MEAS<x> specifies the measurement number.
<NR3> is the maximum number of edges used by the measurement.

slewratemethod `property` ¶

slewratemethod: MeasurementMeasItemEdgesSlewratemethod

Return the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.

Description

This command sets or queries the slew rate method for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?

Info

MEAS<x> specifies the measurement number.
NOMinal specifies the nominal slew rate method.
DDR specifies the DDR slew rate method.

tolevel `property` ¶

tolevel: MeasurementMeasItemEdgesTolevel

Return the MEASUrement:MEAS<x>:EDGES:TOLevel command.

Description

This command sets or queries the ‘to level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
MID specifies the MID level.
LOW specifies the LOW level.

MeasurementMeasItemEdgesFromlevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:FROMLevel command.

Description

This command sets or queries the ‘from level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?

Info

MEAS<x> specifies the measurement number.
MID specifies the MID level.
HIGH specifies the HIGH level.
LOW specifies the LOW level.

MeasurementMeasItemEdgesLevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:LEVel command.

Description

This sets or queries the level type for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
LOW specifies the LOW level.
BOTH specifies both the HIGH and LOW level.

MeasurementMeasItemEdgesN ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:N command.

Description

The command sets or queries the number of accumulation cycles for the measurement when the measurement type is nperiod. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?

Info

MEAS<x> specifies the measurement number.
<NR3> is the maximum number of edges used by the measurement.

MeasurementMeasItemEdgesSlewratemethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.

Description

This command sets or queries the slew rate method for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?

Info

MEAS<x> specifies the measurement number.
NOMinal specifies the nominal slew rate method.
DDR specifies the DDR slew rate method.

MeasurementMeasItemEdgesTolevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:TOLevel command.

Description

This command sets or queries the ‘to level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
MID specifies the MID level.
LOW specifies the LOW level.

MeasurementMeasItemFailcount ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:FAILCount command.

Description

This command returns the number of measurement failures, if applicable, for the selected measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FAILCount? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FAILCount? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:FAILCount?

MeasurementMeasItemFromedge ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMedge command.

Description

This command sets or queries the from edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMedge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMedge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMedge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both the rising and falling edges of the waveform.

MeasurementMeasItemFromedgesearchdirect ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.

Description

This command sets or queries the from edge search direction for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search from the edge.
BACKWard specifies a backward search from the edge.

MeasurementMeasItemGating ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing command.

Description

This command sets or queries the gating type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing?

Info

MEAS<x> is the measurement number for which to return a value.
NONE specifies measurements are taken across the entire record.
SCREEN turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only when the logical state of other waveforms is true.
SEARch specifies that measurements are taken only where the results of a user specified search are found.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Properties

.active: The MEASUrement:MEAS<x>:GATing:ACTive command.
.endtime: The MEASUrement:MEAS<x>:GATing:ENDtime command.
.global: The MEASUrement:MEAS<x>:GATing:GLOBal command.
.hysteresis: The MEASUrement:MEAS<x>:GATing:HYSTeresis command.
.logicsource: The MEASUrement:MEAS<x>:GATing:LOGICSource command.
.midref: The MEASUrement:MEAS<x>:GATing:MIDRef command.
.searchsource: The MEASUrement:MEAS<x>:GATing:SEARCHSource command.
.starttime: The MEASUrement:MEAS<x>:GATing:STARTtime command.

active `property` ¶

active: MeasurementMeasItemGatingActive

Return the MEASUrement:MEAS<x>:GATing:ACTive command.

Description

This command sets or queries the gating active level when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?

Info

MEAS<x> specifies the measurement number.
HIGH takes a measurement when logic gating is High.
LOW takes a measurement when logic gating Low.

endtime `property` ¶

endtime: MeasurementMeasItemGatingEndtime

Return the MEASUrement:MEAS<x>:GATing:ENDtime command.

Description

Sets or queries the end gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

global_ `property` ¶

global_: MeasurementMeasItemGatingGlobal

Return the MEASUrement:MEAS<x>:GATing:GLOBal command.

Description

This command sets or queries the gating settings global flag. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies gate settings can be changed independently for each individual measurement.
ON applies global gate settings to all the measurements’ gate settings.
0 specifies gate settings can be changed independently for each individual measurement.
1 applies global gate settings to all the measurements’ gate settings.

hysteresis `property` ¶

hysteresis: MeasurementMeasItemGatingHysteresis

Return the MEASUrement:MEAS<x>:GATing:HYSTeresis command.

Description

This command sets or queries the gating hysteresis value when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the gating hysteresis.

logicsource `property` ¶

logicsource: MeasurementMeasItemGatingLogicsource

Return the MEASUrement:MEAS<x>:GATing:LOGICSource command.

Description

This command sets or queries the gating data source when the gating type is logic. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:LOGICSource? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:LOGICSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:GATing:LOGICSource?

Info

MEAS<x> specifies the measurement number.

midref `property` ¶

midref: MeasurementMeasItemGatingMidref

Return the MEASUrement:MEAS<x>:GATing:MIDRef command.

Description

This command sets or queries the gating mid ref value when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid ref value for gating.

searchsource `property` ¶

searchsource: MeasurementMeasItemGatingSearchsource

Return the MEASUrement:MEAS<x>:GATing:SEARCHSource command.

Description

This command sets or queries the gating search source when the gating type is search. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
- MEASUrement:MEAS<x>:GATing:SEARCHSource?

Info

MEAS<x> specifies the measurement number.
SEARCH1 is the gating source for search gating.

starttime `property` ¶

starttime: MeasurementMeasItemGatingStarttime

Return the MEASUrement:MEAS<x>:GATing:STARTtime command.

Description

Sets or queries the start gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementMeasItemGatingActive ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:ACTive command.

Description

This command sets or queries the gating active level when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?

Info

MEAS<x> specifies the measurement number.
HIGH takes a measurement when logic gating is High.
LOW takes a measurement when logic gating Low.

MeasurementMeasItemGatingEndtime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:ENDtime command.

Description

Sets or queries the end gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementMeasItemGatingGlobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:GLOBal command.

Description

This command sets or queries the gating settings global flag. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies gate settings can be changed independently for each individual measurement.
ON applies global gate settings to all the measurements’ gate settings.
0 specifies gate settings can be changed independently for each individual measurement.
1 applies global gate settings to all the measurements’ gate settings.

MeasurementMeasItemGatingHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:HYSTeresis command.

Description

This command sets or queries the gating hysteresis value when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the gating hysteresis.

MeasurementMeasItemGatingLogicsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:LOGICSource command.

Description

This command sets or queries the gating data source when the gating type is logic. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:LOGICSource? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:LOGICSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:GATing:LOGICSource?

Info

MEAS<x> specifies the measurement number.

MeasurementMeasItemGatingMidref ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:MIDRef command.

Description

This command sets or queries the gating mid ref value when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid ref value for gating.

MeasurementMeasItemGatingSearchsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:SEARCHSource command.

Description

This command sets or queries the gating search source when the gating type is search. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
- MEASUrement:MEAS<x>:GATing:SEARCHSource?

Info

MEAS<x> specifies the measurement number.
SEARCH1 is the gating source for search gating.

MeasurementMeasItemGatingStarttime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:STARTtime command.

Description

Sets or queries the start gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementMeasItemGlobalref ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GLOBalref command.

Description

This command sets or queries the reference levels global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GLOBalref? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GLOBalref? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GLOBalref value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?

Info

MEAS<x> specifies the measurement number.
OFF allows ref levels to be set separately for each measurement.
ON applies the same ref levels to all measurements.
0 allows ref levels to be set separately for each measurement.
1 applies the same ref levels to all measurements.

MeasurementMeasItemHighrefvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHREFVoltage command.

Description

This command sets or queries the high reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference voltage value for the selected configuration.

MeasurementMeasItemIdletime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:IDLETime command.

Description

This command sets or queries the idle time for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:IDLETime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:IDLETime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:IDLETime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the idle time.

MeasurementMeasItemLabel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LABel command.

Description

This command sets or queries the label for the measurement. As the label can contain non 7-bit ASCII text, it is stored in Percent Encoding format. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LABel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LABel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LABel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LABel <QString>
- MEASUrement:MEAS<x>:LABel?

Info

MEAS<x> specifies the measurement number.
<QString> is the measurement label.

MeasurementMeasItemLowrefvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LOWREFVoltage command.

Description

This command sets or queries the low reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference voltage value for the selected configuration.

MeasurementMeasItemPassfailenabled ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILENabled command.

Description

This command returns or sets the pass/fail test enable status. If enabled, this will turn on pass fail testing for the specified measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?

Info

<NR1> enables or disables pass fail testing for the specified measurement. A value of 1 enables and a value of 0 disables.

MeasurementMeasItemPassfailhighlimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.

Description

This command returns or sets the high limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?

Info

<NR2> sets the high limit for a measurement test. The high limit is a number which a measurement result will be tested against.

MeasurementMeasItemPassfaillimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILLIMit command.

Description

This command returns or sets the limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?

Info

<NR2> sets the limit for a measurement test. The limit is a number which a measurement result will be tested against.

MeasurementMeasItemPassfaillowlimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILLOWlimit command.

Description

This command returns or sets the low limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?

Info

<NR2> sets the low limit for a measurement test. The limit is a number which a measurement result will be tested against.

MeasurementMeasItemPassfailmargin ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILMARgin command.

Description

This command returns or sets the allowed margin for limit comparisons for all pass/fail checks. This is given as a percentage with a default value of 0.05 representing 5%. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?

Info

<NR2> sets the allowed margin for limit comparisons for all pass/fail checks. The margin as a percentage of the limit.

MeasurementMeasItemPassfailwhen ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILWHEN command.

Description

This command sets or returns the condition on which a measurement test fails. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?

Info

LESSthan sets the condition for measurement test failure as less than the given limit. This is the default value.
GREATERthan sets the condition for measurement test failure as greater than the given limit.
Equals sets the condition for measurement test failure as equals the given limit.
NOTEQuals sets the condition for measurement test failure as not equal to the given limit.
INSIDErange sets the condition for measurement test failure as inside the limit range.
OUTSIDErange sets the condition for measurement test failure as outside the limit range.

MeasurementMeasItemPerfreq ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:PERFREQ command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.edge: The MEASUrement:MEAS<x>:PERFREQ:EDGE command.

edge `property` ¶

edge: MeasurementMeasItemPerfreqEdge

Return the MEASUrement:MEAS<x>:PERFREQ:EDGE command.

Description

This command sets or queries the edge type of a Period/Frequency measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
- MEASUrement:MEAS<x>:PERFREQ:EDGE?

Info

MEAS<x> specifies the measurement number.
FIRST computes the measurement between Rising edges if the first edge is Rising. Computes the measurement between Falling edges if the first edge is Falling.
RISE computes the measurement between Rising edges.
FALL computes the measurement between Falling edges.

MeasurementMeasItemPerfreqEdge ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PERFREQ:EDGE command.

Description

This command sets or queries the edge type of a Period/Frequency measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
- MEASUrement:MEAS<x>:PERFREQ:EDGE?

Info

MEAS<x> specifies the measurement number.
FIRST computes the measurement between Rising edges if the first edge is Rising. Computes the measurement between Falling edges if the first edge is Falling.
RISE computes the measurement between Rising edges.
FALL computes the measurement between Falling edges.

MeasurementMeasItemPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:POLarity command.

Description

This command sets or queries the polarity for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POLarity? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POLarity value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?

Info

MEAS<x> specifies the measurement number.
NORMal specifies normal polarity.
INVerted specifies inverted polarity.

MeasurementMeasItemReflevels ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.absolute: The MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

absolute `property` ¶

absolute: MeasurementMeasItemReflevelsAbsolute

Return the MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

MeasurementMeasItemReflevels1 ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1 command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.absolute: The MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.
.basetop: The MEASUrement:MEAS<x>:REFLevels1:BASETop command.
.method: The MEASUrement:MEAS<x>:REFLevels1:METHod command.
.percent: The MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

absolute `property` ¶

absolute: MeasurementMeasItemReflevels1Absolute

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.falllow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementMeasItemReflevels1Basetop

Return the MEASUrement:MEAS<x>:REFLevels1:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?

Info

MEAS<x> specifies the measurement number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

method `property` ¶

method: MeasurementMeasItemReflevels1Method

Return the MEASUrement:MEAS<x>:REFLevels1:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?

Info

MEAS<x> specifies the measurement number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MEAS<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MEAS<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

percent `property` ¶

percent: MeasurementMeasItemReflevels1Percent

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.
.falllow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

MeasurementMeasItemReflevels1Absolute ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.falllow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

falllow `property` ¶

falllow: MeasurementMeasItemReflevels1AbsoluteFalllow

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level in volts. The default is 0.0 V.

fallmid `property` ¶

fallmid: MeasurementMeasItemReflevels1AbsoluteFallmid

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level in volts. The default is 0.0 V.

hysteresis `property` ¶

hysteresis: MeasurementMeasItemReflevels1AbsoluteHysteresis

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for autoset.

risehigh `property` ¶

risehigh: MeasurementMeasItemReflevels1AbsoluteRisehigh

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

riselow `property` ¶

riselow: MeasurementMeasItemReflevels1AbsoluteRiselow

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

risemid `property` ¶

risemid: MeasurementMeasItemReflevels1AbsoluteRisemid

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

type `property` ¶

type: MeasurementMeasItemReflevels1AbsoluteType

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?

Info

MEAS<x> specifies the measurement number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMeasItemReflevels1AbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level in volts. The default is 0.0 V.

MeasurementMeasItemReflevels1AbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level in volts. The default is 0.0 V.

MeasurementMeasItemReflevels1AbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for autoset.

MeasurementMeasItemReflevels1AbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

MeasurementMeasItemReflevels1AbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

MeasurementMeasItemReflevels1AbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

MeasurementMeasItemReflevels1AbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?

Info

MEAS<x> specifies the measurement number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMeasItemReflevels1Basetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?

Info

MEAS<x> specifies the measurement number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

MeasurementMeasItemReflevels1Method ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?

Info

MEAS<x> specifies the measurement number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MEAS<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MEAS<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementMeasItemReflevels1Percent ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.
.falllow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementMeasItemReflevels1PercentFallhigh

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level.

falllow `property` ¶

falllow: MeasurementMeasItemReflevels1PercentFalllow

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level.

fallmid `property` ¶

fallmid: MeasurementMeasItemReflevels1PercentFallmid

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level.

hysteresis `property` ¶

hysteresis: MeasurementMeasItemReflevels1PercentHysteresis

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementMeasItemReflevels1PercentRisehigh

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

riselow `property` ¶

riselow: MeasurementMeasItemReflevels1PercentRiselow

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

risemid `property` ¶

risemid: MeasurementMeasItemReflevels1PercentRisemid

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

type `property` ¶

type: MeasurementMeasItemReflevels1PercentType

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?

Info

MEAS<x> specifies the measurement number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMeasItemReflevels1PercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level.

MeasurementMeasItemReflevels1PercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level.

MeasurementMeasItemReflevels1PercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level.

MeasurementMeasItemReflevels1PercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for the autoset.

MeasurementMeasItemReflevels1PercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementMeasItemReflevels1PercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementMeasItemReflevels1PercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMeasItemReflevels1PercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?

Info

MEAS<x> specifies the measurement number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMeasItemReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

fallhigh `property` ¶

fallhigh: MeasurementMeasItemReflevelsAbsoluteFallhigh

Return the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level in volts. The default is 0.0 V.

MeasurementMeasItemReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level in volts. The default is 0.0 V.

MeasurementMeasItemRefmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFMode command.

Description

This command sets or queries the reference level mode for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFMode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?

Info

MEAS<x> specifies the measurement number.
AUTO sets the reference level for the measurement automatically.
MANual allows the user to set the reference level for the measurement.

MeasurementMeasItemRefvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFVoltage command.

Description

This command sets or queries the reference voltage value for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?

Info

MEAS<x> is the measurement number.
<NR3> is the reference voltage value for the selected configuration.

MeasurementMeasItemResults ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts? query and raise an AssertionError if the returned value does not match value.

Properties

.allacqs: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.

allacqs `property` ¶

allacqs: MeasurementMeasItemResultsAllacqs

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

currentacq `property` ¶

currentacq: MeasurementMeasItemResultsCurrentacq

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

MeasurementMeasItemResultsAllacqs ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemResultsAllacqsMaximum

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum value for all accumulated measurement acquisitions of the specified measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemResultsAllacqsMean

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemResultsAllacqsMinimum

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemResultsAllacqsPk2pk

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak-to-peak value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?

population `property` ¶

population: MeasurementMeasItemResultsAllacqsPopulation

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population measurement value for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemResultsAllacqsStddev

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?

MeasurementMeasItemResultsAllacqsMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum value for all accumulated measurement acquisitions of the specified measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?

MeasurementMeasItemResultsAllacqsMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?

MeasurementMeasItemResultsAllacqsMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?

MeasurementMeasItemResultsAllacqsPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak-to-peak value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?

MeasurementMeasItemResultsAllacqsPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population measurement value for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?

MeasurementMeasItemResultsAllacqsStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?

MeasurementMeasItemResultsCurrentacq ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemResultsCurrentacqMaximum

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemResultsCurrentacqMean

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean value for the measurement for the current acquisition.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemResultsCurrentacqMinimum

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemResultsCurrentacqPk2pk

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak-to-peak value for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?

population `property` ¶

population: MeasurementMeasItemResultsCurrentacqPopulation

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemResultsCurrentacqStddev

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation for the specified measurement for all acquisitions accumulated since statistics were last reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?

MeasurementMeasItemResultsCurrentacqMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?

MeasurementMeasItemResultsCurrentacqMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean value for the measurement for the current acquisition.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?

MeasurementMeasItemResultsCurrentacqMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?

MeasurementMeasItemResultsCurrentacqPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak-to-peak value for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?

MeasurementMeasItemResultsCurrentacqPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?

MeasurementMeasItemResultsCurrentacqStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation for the specified measurement for all acquisitions accumulated since statistics were last reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?

MeasurementMeasItemSignaltype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SIGNALType command.

Description

This command sets or queries the signal type of source 1 for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SIGNALType? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SIGNALType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SIGNALType value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?

Info

MEAS<x> specifies the measurement number.
CLOCK specifies a clock signal type.
DATA specifies a data signal type.
AUTO automatically selects the signal type.

MeasurementMeasItemSource1 ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SOUrce1 command.

Description

This command sets or queries the measurement source. The measurement number and source are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SOUrce1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SOUrce1 value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SOUrce1 {CH<x>|DCH<x>_D<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOUrce1?

Info

MEAS<x> specifies the measurement number.
1 specifies the source number.
CH<x> specifies an analog channel to use as the source.
DCH<x>_D<x> specifies a digital channel to use as the source. The supported digital channel value is 1. The supported digital bit values are 0 to 15.
MATH<x> specifies a math waveform to use as the source.
REF<x> specifies a reference waveform to use as the source.

MeasurementMeasItemStatus ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:STATUS command.

Description

This command returns the pass fail status, if applicable, for the selected measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STATUS? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STATUS? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:STATUS?

Info

PASS specifies that the user specified measurement limit has not been violated.
FAIL specifies that the user specified measurement limit has been violated.

MeasurementMeasItemToedge ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOEdge command.

Description

This command sets or queries the ‘to edge’ type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEdge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEdge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEdge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

MeasurementMeasItemToedgesearchdirect ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.

Description

This command sets or queries the to edge search direction for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search to the edge.
BACKWard specifies a backward search to the edge.

MeasurementMeasItemTransition ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TRANSition command.

Description

This command sets or queries the transition edges flag for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TRANSition? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TRANSition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TRANSition value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:TRANSition?

Info

<NR1> = 1, the measurement is computed on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only. If it is set to 0, the measurement is computed on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
OFF computes the measurement on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
ON computes the measurement on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only.

MeasurementMeasItemType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TYPe command.

Description

This command sets or queries the measurement type for the measurement specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TYPe {ACRMS|AMPlITUDE|AREA|BASE|BURSTWIDTH|DATARATE|DELAY|FALLSLEWRATE|FALLTIME|FREQUENCY|HIGHTIME|HOLD|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NOVERSHOOT|NWIDTH|PDUTY|PERIOD|PHASE|PK2Pk|POVERSHOOT|PWIDTH|RISESLEWRATE|RISETIME|RMS|SETUP|SKEW|TIMEOUTSIDELEVEL|TOP}
- MEASUrement:MEAS<x>:TYPe?

Info

ACRMS (AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIdth (Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SETUP (Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.
SKEW Skew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.

MeasurementMeasItemXunit ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:XUNIT command.

Description

Returns the horizontal scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:XUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:XUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:XUNIT?

Info

MEAS<x> specifies the measurement number.

MeasurementMeasItemYunit ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:YUNIT command.

Description

Returns the vertical scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:YUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:YUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:YUNIT?

Info

MEAS<x> specifies the measurement number.

MeasurementRefItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The MEASUrement:REF<x> command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>? query.
Using the .verify(value) method will send the MEASUrement:REF<x>? query and raise an AssertionError if the returned value does not match value.

Properties

.reflevels: The MEASUrement:REF<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementRefItemReflevels

Return the MEASUrement:REF<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.absolute: The MEASUrement:REF<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REF<x>:REFLevels:BASETop command.
.method: The MEASUrement:REF<x>:REFLevels:METHod command.
.percent: The MEASUrement:REF<x>:REFLevels:PERCent command tree.

MeasurementRefItemReflevels ¶

Bases: SCPICmdRead

The MEASUrement:REF<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Properties

.absolute: The MEASUrement:REF<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REF<x>:REFLevels:BASETop command.
.method: The MEASUrement:REF<x>:REFLevels:METHod command.
.percent: The MEASUrement:REF<x>:REFLevels:PERCent command tree.

absolute `property` ¶

absolute: MeasurementRefItemReflevelsAbsolute

Return the MEASUrement:REF<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementRefItemReflevelsBasetop

Return the MEASUrement:REF<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REF<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

method `property` ¶

method: MeasurementRefItemReflevelsMethod

Return the MEASUrement:REF<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REF<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REF<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

percent `property` ¶

percent: MeasurementRefItemReflevelsPercent

Return the MEASUrement:REF<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

MeasurementRefItemReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementRefItemReflevelsAbsoluteFallhigh

Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

falllow `property` ¶

falllow: MeasurementRefItemReflevelsAbsoluteFalllow

Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

fallmid `property` ¶

fallmid: MeasurementRefItemReflevelsAbsoluteFallmid

Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

hysteresis `property` ¶

hysteresis: MeasurementRefItemReflevelsAbsoluteHysteresis

Return the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

risehigh `property` ¶

risehigh: MeasurementRefItemReflevelsAbsoluteRisehigh

Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

riselow `property` ¶

riselow: MeasurementRefItemReflevelsAbsoluteRiselow

Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

risemid `property` ¶

risemid: MeasurementRefItemReflevelsAbsoluteRisemid

Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

type `property` ¶

type: MeasurementRefItemReflevelsAbsoluteType

Return the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementRefItemReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementRefItemReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REF<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

MeasurementRefItemReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REF<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REF<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementRefItemReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementRefItemReflevelsPercentFallhigh

Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

falllow `property` ¶

falllow: MeasurementRefItemReflevelsPercentFalllow

Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the low reference level.

fallmid `property` ¶

fallmid: MeasurementRefItemReflevelsPercentFallmid

Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

hysteresis `property` ¶

hysteresis: MeasurementRefItemReflevelsPercentHysteresis

Return the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

risehigh `property` ¶

risehigh: MeasurementRefItemReflevelsPercentRisehigh

Return the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

riselow `property` ¶

riselow: MeasurementRefItemReflevelsPercentRiselow

Return the MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

risemid `property` ¶

risemid: MeasurementRefItemReflevelsPercentRisemid

Return the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

type `property` ¶

type: MeasurementRefItemReflevelsPercentType

Return the MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementRefItemReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

MeasurementRefItemReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the low reference level.

MeasurementRefItemReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

MeasurementRefItemReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

MeasurementRefItemReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

MeasurementRefItemReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

MeasurementRefItemReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

MeasurementRefItemReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementReflevels ¶

Bases: SCPICmdRead

The MEASUrement:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REFLevels? query and raise an AssertionError if the returned value does not match value.

Properties

.absolute: The MEASUrement:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REFLevels:BASETop command.
.method: The MEASUrement:REFLevels:METHod command.
.mode: The MEASUrement:REFLevels:MODE command.
.percent: The MEASUrement:REFLevels:PERCent command tree.
.type: The MEASUrement:REFLevels:TYPE command.

absolute `property` ¶

absolute: MeasurementReflevelsAbsolute

Return the MEASUrement:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementReflevelsBasetop

Return the MEASUrement:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?

Info

AUTO sets the base top method to AUTO.
MINMax sets the base top method to MINMax.
MEANhistogram sets the base top method to MEANhistogram.
MODEhistogram sets the base top method to MODEhistogram.
EYEhistogram sets the base top method to EYEhistogram.

method `property` ¶

method: MeasurementReflevelsMethod

Return the MEASUrement:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REFLevels:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REFLevels:REFLevel:ABSolute commands. This method is useful when precise values are required.

mode `property` ¶

mode: MeasurementReflevelsMode

Return the MEASUrement:REFLevels:MODE command.

Description

This command sets or queries how often reference levels are calculated.

Usage

Using the .query() method will send the MEASUrement:REFLevels:MODE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:MODE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:MODE value command.

SCPI Syntax

- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?

Info

LATCh calculates reference levels only on the first acquisition after a statistics reset.
CONTinuous calculates reference levels on every acquisition.

percent `property` ¶

percent: MeasurementReflevelsPercent

Return the MEASUrement:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REFLevels:PERCent:TYPE command.

type `property` ¶

type: MeasurementReflevelsType

Return the MEASUrement:REFLevels:TYPE command.

Description

This command sets or queries the shared reference level method used for sources of measurement calculations.

Usage

Using the .query() method will send the MEASUrement:REFLevels:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?

Info

GLOBal shares reference levels across measurements.
PERSource causes reference levels to be used on individual measurements.

MeasurementReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementReflevelsAbsoluteFallhigh

Return the MEASUrement:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

falllow `property` ¶

falllow: MeasurementReflevelsAbsoluteFalllow

Return the MEASUrement:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge.

fallmid `property` ¶

fallmid: MeasurementReflevelsAbsoluteFallmid

Return the MEASUrement:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge.

hysteresis `property` ¶

hysteresis: MeasurementReflevelsAbsoluteHysteresis

Return the MEASUrement:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level.

risehigh `property` ¶

risehigh: MeasurementReflevelsAbsoluteRisehigh

Return the MEASUrement:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge.

riselow `property` ¶

riselow: MeasurementReflevelsAbsoluteRiselow

Return the MEASUrement:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the the low reference level of the rising edge.

risemid `property` ¶

risemid: MeasurementReflevelsAbsoluteRisemid

Return the MEASUrement:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge.

type `property` ¶

type: MeasurementReflevelsAbsoluteType

Return the MEASUrement:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge.

MeasurementReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge.

MeasurementReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level.

MeasurementReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge.

MeasurementReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the the low reference level of the rising edge.

MeasurementReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge.

MeasurementReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?

Info

AUTO sets the base top method to AUTO.
MINMax sets the base top method to MINMax.
MEANhistogram sets the base top method to MEANhistogram.
MODEhistogram sets the base top method to MODEhistogram.
EYEhistogram sets the base top method to EYEhistogram.

MeasurementReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REFLevels:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REFLevels:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementReflevelsMode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:MODE command.

Description

This command sets or queries how often reference levels are calculated.

Usage

Using the .query() method will send the MEASUrement:REFLevels:MODE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:MODE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:MODE value command.

SCPI Syntax

- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?

Info

LATCh calculates reference levels only on the first acquisition after a statistics reset.
CONTinuous calculates reference levels on every acquisition.

MeasurementReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementReflevelsPercentFallhigh

Return the MEASUrement:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

falllow `property` ¶

falllow: MeasurementReflevelsPercentFalllow

Return the MEASUrement:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

fallmid `property` ¶

fallmid: MeasurementReflevelsPercentFallmid

Return the MEASUrement:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

hysteresis `property` ¶

hysteresis: MeasurementReflevelsPercentHysteresis

Return the MEASUrement:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

risehigh `property` ¶

risehigh: MeasurementReflevelsPercentRisehigh

Return the MEASUrement:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

riselow `property` ¶

riselow: MeasurementReflevelsPercentRiselow

Return the MEASUrement:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

risemid `property` ¶

risemid: MeasurementReflevelsPercentRisemid

Return the MEASUrement:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

type `property` ¶

type: MeasurementReflevelsPercentType

Return the MEASUrement:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

MeasurementReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

MeasurementReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

MeasurementReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

MeasurementReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

MeasurementReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

MeasurementReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

MeasurementReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementReflevelsType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:TYPE command.

Description

This command sets or queries the shared reference level method used for sources of measurement calculations.

Usage

Using the .query() method will send the MEASUrement:REFLevels:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?

Info

GLOBal shares reference levels across measurements.
PERSource causes reference levels to be used on individual measurements.

MeasurementStatistics ¶

Bases: SCPICmdRead

The MEASUrement:STATIstics command tree.

Usage

Using the .query() method will send the MEASUrement:STATIstics? query.
Using the .verify(value) method will send the MEASUrement:STATIstics? query and raise an AssertionError if the returned value does not match value.

Properties

.cyclemode: The MEASUrement:STATIstics:CYCLEMode command.

cyclemode `property` ¶

cyclemode: MeasurementStatisticsCyclemode

Return the MEASUrement:STATIstics:CYCLEMode command.

Description

This command turns on and off cycle to cycle measurement statistics tracking and affects computation and display of cycle-cycle statistics in the Measurement Result table. It affects measurement statistics after being enabled and after new data is acquired and measured.

Usage

Using the .query() method will send the MEASUrement:STATIstics:CYCLEMode? query.
Using the .verify(value) method will send the MEASUrement:STATIstics:CYCLEMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:STATIstics:CYCLEMode value command.

SCPI Syntax

- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?

Info

OFF turns off statistics for all measurements. This is the default value.
ON turns on statistics and displays all statistics for each measurement.
0 turns off statistics for all measurements.
1 turns on statistics and displays all statistics for each measurement.

MeasurementStatisticsCyclemode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:STATIstics:CYCLEMode command.

Description

This command turns on and off cycle to cycle measurement statistics tracking and affects computation and display of cycle-cycle statistics in the Measurement Result table. It affects measurement statistics after being enabled and after new data is acquired and measured.

Usage

Using the .query() method will send the MEASUrement:STATIstics:CYCLEMode? query.
Using the .verify(value) method will send the MEASUrement:STATIstics:CYCLEMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:STATIstics:CYCLEMode value command.

SCPI Syntax

- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?

Info

OFF turns off statistics for all measurements. This is the default value.
ON turns on statistics and displays all statistics for each measurement.
0 turns off statistics for all measurements.
1 turns on statistics and displays all statistics for each measurement.

measurement ¶

Measurement ¶

addmeas property ¶

addnew property ¶

annotate property ¶

ch property ¶

delete property ¶

deleteall property ¶

edge property ¶

gating property ¶

interp property ¶

list property ¶

math property ¶

meas property ¶

ref property ¶

reflevels property ¶

statistics property ¶

MeasurementAddmeas ¶

MeasurementAddnew ¶

MeasurementAnnotate ¶

MeasurementChannel ¶

reflevels property ¶

MeasurementChannelReflevels ¶

absolute property ¶

basetop property ¶

method property ¶

percent property ¶

MeasurementChannelReflevelsAbsolute ¶

fallhigh property ¶

falllow property ¶

fallmid property ¶

hysteresis property ¶

risehigh property ¶

riselow property ¶

risemid property ¶

type property ¶

MeasurementChannelReflevelsAbsoluteFallhigh ¶

MeasurementChannelReflevelsAbsoluteFalllow ¶

MeasurementChannelReflevelsAbsoluteFallmid ¶

MeasurementChannelReflevelsAbsoluteHysteresis ¶

MeasurementChannelReflevelsAbsoluteRisehigh ¶

MeasurementChannelReflevelsAbsoluteRiselow ¶

MeasurementChannelReflevelsAbsoluteRisemid ¶

MeasurementChannelReflevelsAbsoluteType ¶

MeasurementChannelReflevelsBasetop ¶

MeasurementChannelReflevelsMethod ¶

MeasurementChannelReflevelsPercent ¶

fallhigh property ¶

falllow property ¶

fallmid property ¶

hysteresis property ¶

risehigh property ¶

riselow property ¶

risemid property ¶

type property ¶

MeasurementChannelReflevelsPercentFallhigh ¶

MeasurementChannelReflevelsPercentFalllow ¶

MeasurementChannelReflevelsPercentFallmid ¶

MeasurementChannelReflevelsPercentHysteresis ¶

MeasurementChannelReflevelsPercentRisehigh ¶

MeasurementChannelReflevelsPercentRiselow ¶

MeasurementChannelReflevelsPercentRisemid ¶

MeasurementChannelReflevelsPercentType ¶

MeasurementDelete ¶

MeasurementDeleteall ¶

MeasurementEdgeItem ¶

MeasurementGating ¶

active property ¶

endtime property ¶

hysteresis property ¶

logicsource property ¶

midref property ¶

searchsource property ¶

starttime property ¶

MeasurementGatingActive ¶

MeasurementGatingEndtime ¶

MeasurementGatingHysteresis ¶

MeasurementGatingLogicsource ¶

MeasurementGatingMidref ¶

MeasurementGatingSearchsource ¶

addmeas `property` ¶

addnew `property` ¶

annotate `property` ¶

ch `property` ¶

delete `property` ¶

deleteall `property` ¶

edge `property` ¶

gating `property` ¶

interp `property` ¶

list `property` ¶

math `property` ¶

meas `property` ¶

ref `property` ¶

reflevels `property` ¶

statistics `property` ¶

reflevels `property` ¶

absolute `property` ¶

basetop `property` ¶

method `property` ¶

percent `property` ¶

fallhigh `property` ¶

falllow `property` ¶

fallmid `property` ¶

hysteresis `property` ¶

risehigh `property` ¶

riselow `property` ¶

risemid `property` ¶

type `property` ¶

fallhigh `property` ¶

falllow `property` ¶

fallmid `property` ¶

hysteresis `property` ¶

risehigh `property` ¶

riselow `property` ¶

risemid `property` ¶

type `property` ¶

active `property` ¶

endtime `property` ¶

hysteresis `property` ¶

logicsource `property` ¶

midref `property` ¶

searchsource `property` ¶

starttime `property` ¶

reflevels `property` ¶

absolute `property` ¶

basetop `property` ¶

method `property` ¶

percent `property` ¶

fallhigh `property` ¶

falllow `property` ¶

fallmid `property` ¶

hysteresis `property` ¶

risehigh `property` ¶

riselow `property` ¶

risemid `property` ¶

type `property` ¶

fallhigh `property` ¶

falllow `property` ¶

fallmid `property` ¶

hysteresis `property` ¶

risehigh `property` ¶

riselow `property` ¶

risemid `property` ¶

type `property` ¶

burstedgtype `property` ¶

ccresults `property` ¶

delay `property` ¶

displaystat `property` ¶

edge `property` ¶

edgeincre `property` ¶

edges `property` ¶

failcount `property` ¶

fromedge `property` ¶

fromedgesearchdirect `property` ¶

gating `property` ¶

globalref `property` ¶

highrefvoltage `property` ¶

idletime `property` ¶

label `property` ¶

lowrefvoltage `property` ¶