auxin ¶

The auxin commands module.

These commands are used in the following models: DPO5K, DPO5KB, DPO70KC, DPO70KD, DPO70KDX, DPO70KSX, DPO7K, DPO7KC, DSA70KC, DSA70KD, MSO5K, MSO5KB, MSO70KC, MSO70KDX

THIS FILE IS AUTO-GENERATED, IT SHOULD NOT BE MANUALLY MODIFIED.

Please report an issue if one is found.

Commands and Queries

- AUXIn:BANdwidth <NR3>
- AUXIn:BANdwidth?
- AUXIn:COUPling <NR3>
- AUXIn:COUPling?
- AUXIn:OFFSet <NR3>
- AUXIn:OFFSet?
- AUXIn:PROBEFunc:EXTAtten <NR3>
- AUXIn:PROBEFunc:EXTAtten?
- AUXIn:PROBEFunc:EXTDBatten <NR3>
- AUXIn:PROBEFunc:EXTDBatten?
- AUXIn:PROBEFunc:EXTUnits <QString>
- AUXIn:PROBEFunc:EXTUnits?
- AUXIn:PRObe:AUTOZero EXECute
- AUXIn:PRObe:DEGAUSS EXECute
- AUXIn:PRObe:DEGAUSS:STATE?
- AUXIn:PRObe:FORCEDRange <NR3>
- AUXIn:PRObe:FORCEDRange?
- AUXIn:PRObe:GAIN?
- AUXIn:PRObe:ID:SERnumber?
- AUXIn:PRObe:ID:TYPe?
- AUXIn:PRObe:INPUTMode {COMmonmode|DEFault|DIFFerential|A|B}
- AUXIn:PRObe:INPUTMode:AOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:AOFFSet?
- AUXIn:PRObe:INPUTMode:BOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:BOFFSet?
- AUXIn:PRObe:INPUTMode:CMOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:CMOFFSet?
- AUXIn:PRObe:INPUTMode:DMOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:DMOFFSet?
- AUXIn:PRObe:INPUTMode?
- AUXIn:PRObe:RANge {ATTEN1X|ATTEN1_25X|ATTEN1_5X|ATTEN1_75X|ATTEN2X|ATTEN2_5X|ATTEN3X|ATTEN3_5X|ATTEN4X|ATTEN4_5X|ATTEN5X|ATTEN5_5X|ATTEN6X|ATTEN6_5X|ATTEN7X|ATTEN7_5X|ATTEN8X|ATTEN8_5X|ATTEN9X|ATTEN9_5X|ATTEN10X|ATTEN12_5X|ATTEN15X|ATTEN17_5X|ATTEN20X|ATTEN25X|ATTEN30X|ATTEN35X|ATTEN40X|ATTEN45X|ATTEN50X|ATTEN55X|ATTEN60X|ATTEN65X|ATTEN70X|ATTEN75X|ATTEN80X|ATTEN85X|ATTEN90X|ATTEN95X|ATTEN100X|ATTEN125X|ATTEN150X|ATTEN175X|ATTEN200X|ATTEN250X|ATTEN300X|ATTEN350X|ATTEN400X|ATTEN450X|ATTEN500X|ATTEN550X|ATTEN600X|ATTEN650X|ATTEN700X|ATTEN750X|ATTEN800X|ATTEN850X|ATTEN900X|ATTEN950X|ATTEN1000X}
- AUXIn:PRObe:RANge?
- AUXIn:PRObe:RESistance?
- AUXIn:PRObe:SET <QString>
- AUXIn:PRObe:SET?
- AUXIn:PRObe:SIGnal {PASS|BYPass}
- AUXIn:PRObe:SIGnal?
- AUXIn:PRObe:TIPtype {HBWStraightflex|OTHer}
- AUXIn:PRObe:TIPtype?
- AUXIn:PRObe:UNIts?
- AUXIn:VTERm:DUAL:A <NR3>
- AUXIn:VTERm:DUAL:A?
- AUXIn:VTERm:DUAL:B <NR3>
- AUXIn:VTERm:DUAL:B?

Auxin ¶

Bases: SCPICmdRead

The AUXIn command tree.

Usage

Using the .query() method will send the AUXIn? query.
Using the .verify(value) method will send the AUXIn? query and raise an AssertionError if the returned value does not match value.

Properties

.bandwidth: The AUXIn:BANdwidth command.
.coupling: The AUXIn:COUPling command.
.offset: The AUXIn:OFFSet command.
.probefunc: The AUXIn:PROBEFunc command tree.
.probe: The AUXIn:PRObe command tree.
.vterm: The AUXIn:VTERm command tree.

bandwidth `property` ¶

bandwidth: AuxinBandwidth

Return the AUXIn:BANdwidth command.

Description

This command sets or queries the selectable low-pass bandwidth limit filter of the AUX In input. The bandwidth will change with an appropriate probe attached. This is equivalent to selecting Bandwidth from the Vertical menu. The query form of this command always returns the maximum bandwidth of the AUX In input.

Usage

Using the .query() method will send the AUXIn:BANdwidth? query.
Using the .verify(value) method will send the AUXIn:BANdwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:BANdwidth value command.

SCPI Syntax

- AUXIn:BANdwidth <NR3>
- AUXIn:BANdwidth?

Info

<NR3> is one of the supported bandwidths on the attached probe.

coupling `property` ¶

coupling: AuxinCoupling

Return the AUXIn:COUPling command.

Description

This command sets or queries the input attenuator coupling setting for the AUX In input. The coupling will change with an appropriate probe attached. This command is equivalent to selecting Coupling from the Vertical menu.

Usage

Using the .query() method will send the AUXIn:COUPling? query.
Using the .verify(value) method will send the AUXIn:COUPling? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:COUPling value command.

SCPI Syntax

- AUXIn:COUPling <NR3>
- AUXIn:COUPling?

Info

<NR3> is one of the supported input attenuator couplings on the attached probe.

offset `property` ¶

offset: AuxinOffset

Return the AUXIn:OFFSet command.

Description

This command sets or queries the vertical offset for the AUX In input. This command is equivalent to selecting Offset from the Vertical menu. This command offsets the vertical acquisition window (moves the level at the vertical center of the acquisition window) for the input. Visualize offset as scrolling the acquisition window towards the top of a large signal for increased offset values, and scrolling towards the bottom for decreased offset values. The resolution of the vertical window sets the offset increment for this control. Offset adjusts only the vertical center of the acquisition window to help determine what data is acquired. The instrument always displays the input signal minus the offset value. The channel reference marker will move to the vertical graticule position given by the negative of the offset value divided by the scale factor, unless that position is off-screen. If the computed coordinate for the reference mark is off-screen, the mark moves to the nearest screen limit and changes from a right-pointing arrow ( →) to an arrow pointing in the appropriate off-screen direction.

Usage

Using the .query() method will send the AUXIn:OFFSet? query.
Using the .verify(value) method will send the AUXIn:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:OFFSet value command.

SCPI Syntax

- AUXIn:OFFSet <NR3>
- AUXIn:OFFSet?

Info

<NR3> is the offset value for the specified channel.

probe `property` ¶

probe: AuxinProbe

Return the AUXIn:PRObe command tree.

Usage

Using the .query() method will send the AUXIn:PRObe? query.
Using the .verify(value) method will send the AUXIn:PRObe? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.autozero: The AUXIn:PRObe:AUTOZero command.
.degauss: The AUXIn:PRObe:DEGAUSS command.
.forcedrange: The AUXIn:PRObe:FORCEDRange command.
.gain: The AUXIn:PRObe:GAIN command.
.id: The AUXIn:PRObe:ID command tree.
.inputmode: The AUXIn:PRObe:INPUTMode command.
.range: The AUXIn:PRObe:RANge command.
.resistance: The AUXIn:PRObe:RESistance command.
.set: The AUXIn:PRObe:SET command.
.signal: The AUXIn:PRObe:SIGnal command.
.tiptype: The AUXIn:PRObe:TIPtype command.
.units: The AUXIn:PRObe:UNIts command.

probefunc `property` ¶

probefunc: AuxinProbefunc

Return the AUXIn:PROBEFunc command tree.

Usage

Using the .query() method will send the AUXIn:PROBEFunc? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.extatten: The AUXIn:PROBEFunc:EXTAtten command.
.extdbatten: The AUXIn:PROBEFunc:EXTDBatten command.
.extunits: The AUXIn:PROBEFunc:EXTUnits command.

vterm `property` ¶

vterm: AuxinVterm

Return the AUXIn:VTERm command tree.

Usage

Using the .query() method will send the AUXIn:VTERm? query.
Using the .verify(value) method will send the AUXIn:VTERm? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.dual: The AUXIn:VTERm:DUAL command tree.

AuxinBandwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:BANdwidth command.

Description

This command sets or queries the selectable low-pass bandwidth limit filter of the AUX In input. The bandwidth will change with an appropriate probe attached. This is equivalent to selecting Bandwidth from the Vertical menu. The query form of this command always returns the maximum bandwidth of the AUX In input.

Usage

Using the .query() method will send the AUXIn:BANdwidth? query.
Using the .verify(value) method will send the AUXIn:BANdwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:BANdwidth value command.

SCPI Syntax

- AUXIn:BANdwidth <NR3>
- AUXIn:BANdwidth?

Info

<NR3> is one of the supported bandwidths on the attached probe.

AuxinCoupling ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:COUPling command.

Description

This command sets or queries the input attenuator coupling setting for the AUX In input. The coupling will change with an appropriate probe attached. This command is equivalent to selecting Coupling from the Vertical menu.

Usage

Using the .query() method will send the AUXIn:COUPling? query.
Using the .verify(value) method will send the AUXIn:COUPling? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:COUPling value command.

SCPI Syntax

- AUXIn:COUPling <NR3>
- AUXIn:COUPling?

Info

<NR3> is one of the supported input attenuator couplings on the attached probe.

AuxinOffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:OFFSet command.

Description

This command sets or queries the vertical offset for the AUX In input. This command is equivalent to selecting Offset from the Vertical menu. This command offsets the vertical acquisition window (moves the level at the vertical center of the acquisition window) for the input. Visualize offset as scrolling the acquisition window towards the top of a large signal for increased offset values, and scrolling towards the bottom for decreased offset values. The resolution of the vertical window sets the offset increment for this control. Offset adjusts only the vertical center of the acquisition window to help determine what data is acquired. The instrument always displays the input signal minus the offset value. The channel reference marker will move to the vertical graticule position given by the negative of the offset value divided by the scale factor, unless that position is off-screen. If the computed coordinate for the reference mark is off-screen, the mark moves to the nearest screen limit and changes from a right-pointing arrow ( →) to an arrow pointing in the appropriate off-screen direction.

Usage

Using the .query() method will send the AUXIn:OFFSet? query.
Using the .verify(value) method will send the AUXIn:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:OFFSet value command.

SCPI Syntax

- AUXIn:OFFSet <NR3>
- AUXIn:OFFSet?

Info

<NR3> is the offset value for the specified channel.

AuxinProbe ¶

Bases: SCPICmdRead

The AUXIn:PRObe command tree.

Usage

Using the .query() method will send the AUXIn:PRObe? query.
Using the .verify(value) method will send the AUXIn:PRObe? query and raise an AssertionError if the returned value does not match value.

Properties

.autozero: The AUXIn:PRObe:AUTOZero command.
.degauss: The AUXIn:PRObe:DEGAUSS command.
.forcedrange: The AUXIn:PRObe:FORCEDRange command.
.gain: The AUXIn:PRObe:GAIN command.
.id: The AUXIn:PRObe:ID command tree.
.inputmode: The AUXIn:PRObe:INPUTMode command.
.range: The AUXIn:PRObe:RANge command.
.resistance: The AUXIn:PRObe:RESistance command.
.set: The AUXIn:PRObe:SET command.
.signal: The AUXIn:PRObe:SIGnal command.
.tiptype: The AUXIn:PRObe:TIPtype command.
.units: The AUXIn:PRObe:UNIts command.

autozero `property` ¶

autozero: AuxinProbeAutozero

Return the AUXIn:PRObe:AUTOZero command.

Description

The command sets the probe attached to the AUX In input to autozero.

Usage

Using the .write(value) method will send the AUXIn:PRObe:AUTOZero value command.

SCPI Syntax

- AUXIn:PRObe:AUTOZero EXECute

Info

EXECute sets the probe to autozero.

degauss `property` ¶

degauss: AuxinProbeDegauss

Return the AUXIn:PRObe:DEGAUSS command.

Description

This command starts a degauss cycle of the probe attached to the AUX In input. The degauss cycle will change with an appropriate probe attached.

Usage

Using the .write(value) method will send the AUXIn:PRObe:DEGAUSS value command.

SCPI Syntax

- AUXIn:PRObe:DEGAUSS EXECute

Info

EXECute starts a probe degauss cycle.

Sub-properties

.state: The AUXIn:PRObe:DEGAUSS:STATE command.

forcedrange `property` ¶

forcedrange: AuxinProbeForcedrange

Return the AUXIn:PRObe:FORCEDRange command.

Description

This command sets the probe attached to the AUX In input to the specified range, or the command queries the probe range.

Usage

Using the .query() method will send the AUXIn:PRObe:FORCEDRange? query.
Using the .verify(value) method will send the AUXIn:PRObe:FORCEDRange? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:FORCEDRange value command.

SCPI Syntax

- AUXIn:PRObe:FORCEDRange <NR3>
- AUXIn:PRObe:FORCEDRange?

Info

<NR3> specifies the probe range.

gain `property` ¶

gain: AuxinProbeGain

Return the AUXIn:PRObe:GAIN command.

Description

This query-only command returns the gain factor of the probe that is attached to the AUX In input. The ‘gain’ of a probe is the output divided by the input transfer ratio. For example, a common 10x probe has a gain of 0.1.

Usage

Using the .query() method will send the AUXIn:PRObe:GAIN? query.
Using the .verify(value) method will send the AUXIn:PRObe:GAIN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:GAIN?

id `property` ¶

id: AuxinProbeId

Return the AUXIn:PRObe:ID command tree.

Usage

Using the .query() method will send the AUXIn:PRObe:ID? query.
Using the .verify(value) method will send the AUXIn:PRObe:ID? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.sernumber: The AUXIn:PRObe:ID:SERnumber command.
.type: The AUXIn:PRObe:ID:TYPe command.

inputmode `property` ¶

inputmode: AuxinProbeInputmode

Return the AUXIn:PRObe:INPUTMode command.

Description

This command sets or queries one of the probe’s four input modes on the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode {COMmonmode|DEFault|DIFFerential|A|B}
- AUXIn:PRObe:INPUTMode?

Info

COMmonmode sets the probe to route common-mode signals to the host.
DEFault sets the probe to the default mode.
DIFFerential sets the probe to route differential signals to the host.
A sets the probe to route single-ended A signals to the host.
B sets the probe to route single-ended B signals to the host.

Sub-properties

.aoffset: The AUXIn:PRObe:INPUTMode:AOFFSet command.
.boffset: The AUXIn:PRObe:INPUTMode:BOFFSet command.
.cmoffset: The AUXIn:PRObe:INPUTMode:CMOFFSet command.
.dmoffset: The AUXIn:PRObe:INPUTMode:DMOFFSet command.

range `property` ¶

range: AuxinProbeRange

Return the AUXIn:PRObe:RANge command.

Description

This command controls or queries the set attenuation range of the probe on the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:RANge? query.
Using the .verify(value) method will send the AUXIn:PRObe:RANge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:RANge value command.

SCPI Syntax

- AUXIn:PRObe:RANge {ATTEN1X|ATTEN1_25X|ATTEN1_5X|ATTEN1_75X|ATTEN2X|ATTEN2_5X|ATTEN3X|ATTEN3_5X|ATTEN4X|ATTEN4_5X|ATTEN5X|ATTEN5_5X|ATTEN6X|ATTEN6_5X|ATTEN7X|ATTEN7_5X|ATTEN8X|ATTEN8_5X|ATTEN9X|ATTEN9_5X|ATTEN10X|ATTEN12_5X|ATTEN15X|ATTEN17_5X|ATTEN20X|ATTEN25X|ATTEN30X|ATTEN35X|ATTEN40X|ATTEN45X|ATTEN50X|ATTEN55X|ATTEN60X|ATTEN65X|ATTEN70X|ATTEN75X|ATTEN80X|ATTEN85X|ATTEN90X|ATTEN95X|ATTEN100X|ATTEN125X|ATTEN150X|ATTEN175X|ATTEN200X|ATTEN250X|ATTEN300X|ATTEN350X|ATTEN400X|ATTEN450X|ATTEN500X|ATTEN550X|ATTEN600X|ATTEN650X|ATTEN700X|ATTEN750X|ATTEN800X|ATTEN850X|ATTEN900X|ATTEN950X|ATTEN1000X}
- AUXIn:PRObe:RANge?

resistance `property` ¶

resistance: AuxinProbeResistance

Return the AUXIn:PRObe:RESistance command.

Description

This query-only command returns the resistance factor of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:RESistance? query.
Using the .verify(value) method will send the AUXIn:PRObe:RESistance? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:RESistance?

set_ `property` ¶

set_: AuxinProbeSet

Return the AUXIn:PRObe:SET command.

Description

This command sets or queries aspects of probe accessory user interfaces, for example probe attenuation factors. The available arguments for this command will vary depending on the accessory you attach to the instrument auxiliary trigger input. For the P7260 probe, you can select between two attenuation factors using either this GPIB command or the push switch on the probe. The probe enables the relevant path and adjusts the settings based on the characteristics of the path in use. The probe signal path selection is not kept in persistent storage. The probe will lose the selection if you reboot the instrument or remove the probe. Also, the instrument does not store the selection in the save/recall setup operation.

Usage

Using the .query() method will send the AUXIn:PRObe:SET? query.
Using the .verify(value) method will send the AUXIn:PRObe:SET? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:SET value command.

SCPI Syntax

- AUXIn:PRObe:SET <QString>
- AUXIn:PRObe:SET?

Info

<QString> is a quoted string representing a settable aspect of the attached accessory.
ATTENUATION 5X sets the P7260 probe to ±0.75 V dynamic range with 6 GHz bandwidth and 5X attenuation.
ATTENUATION 25X sets the P7260 probe to ±3 V dynamic range with 6 GHz bandwidth and 25X attenuation.
VTERMsource AUTO sets the P7380SMA probe voltage termination source to auto.
VTERMsource INTernal sets the P7380SMA probe voltage termination source to internal.
VTERMsource EXTernal sets the P7380SMA probe voltage termination source to external.

signal `property` ¶

signal: AuxinProbeSignal

Return the AUXIn:PRObe:SIGnal command.

Description

This command sets or queries aspects of probe accessory user interfaces. The available arguments for this command will vary depending on the accessory you attach to the instrument.

Usage

Using the .query() method will send the AUXIn:PRObe:SIGnal? query.
Using the .verify(value) method will send the AUXIn:PRObe:SIGnal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:SIGnal value command.

SCPI Syntax

- AUXIn:PRObe:SIGnal {PASS|BYPass}
- AUXIn:PRObe:SIGnal?

Info

PASS opens a relay passing your signal to the instrument.
BYPass closes a relay preventing your signal from reaching the instrument. During probe degauss, the signal should be bypassed.

tiptype `property` ¶

tiptype: AuxinProbeTiptype

Return the AUXIn:PRObe:TIPtype command.

Description

This command sets or queries the type of probe tip being used.

Usage

Using the .query() method will send the AUXIn:PRObe:TIPtype? query.
Using the .verify(value) method will send the AUXIn:PRObe:TIPtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:TIPtype value command.

SCPI Syntax

- AUXIn:PRObe:TIPtype {HBWStraightflex|OTHer}
- AUXIn:PRObe:TIPtype?

Info

HBWStraightflex lets the instrument know you are using a high bandwidth straight-flex probe tip.
OTHer lets the instrument know you are not using a high bandwidth straight-flex probe tip.

units `property` ¶

units: AuxinProbeUnits

Return the AUXIn:PRObe:UNIts command.

Description

This query-only command returns a string describing the units of measure for the probe attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:UNIts? query.
Using the .verify(value) method will send the AUXIn:PRObe:UNIts? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:UNIts?

AuxinProbeAutozero ¶

Bases: SCPICmdWrite

The AUXIn:PRObe:AUTOZero command.

Description

The command sets the probe attached to the AUX In input to autozero.

Usage

Using the .write(value) method will send the AUXIn:PRObe:AUTOZero value command.

SCPI Syntax

- AUXIn:PRObe:AUTOZero EXECute

Info

EXECute sets the probe to autozero.

AuxinProbeDegauss ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:DEGAUSS command.

Description

This command starts a degauss cycle of the probe attached to the AUX In input. The degauss cycle will change with an appropriate probe attached.

Usage

Using the .write(value) method will send the AUXIn:PRObe:DEGAUSS value command.

SCPI Syntax

- AUXIn:PRObe:DEGAUSS EXECute

Info

EXECute starts a probe degauss cycle.

Properties

.state: The AUXIn:PRObe:DEGAUSS:STATE command.

state `property` ¶

state: AuxinProbeDegaussState

Return the AUXIn:PRObe:DEGAUSS:STATE command.

Description

This command queries whether the probe attached to the AUX In input is degaussed.

Usage

Using the .query() method will send the AUXIn:PRObe:DEGAUSS:STATE? query.
Using the .verify(value) method will send the AUXIn:PRObe:DEGAUSS:STATE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:DEGAUSS:STATE?

AuxinProbeDegaussState ¶

Bases: SCPICmdRead

The AUXIn:PRObe:DEGAUSS:STATE command.

Description

This command queries whether the probe attached to the AUX In input is degaussed.

Usage

Using the .query() method will send the AUXIn:PRObe:DEGAUSS:STATE? query.
Using the .verify(value) method will send the AUXIn:PRObe:DEGAUSS:STATE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:DEGAUSS:STATE?

AuxinProbeForcedrange ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:FORCEDRange command.

Description

This command sets the probe attached to the AUX In input to the specified range, or the command queries the probe range.

Usage

Using the .query() method will send the AUXIn:PRObe:FORCEDRange? query.
Using the .verify(value) method will send the AUXIn:PRObe:FORCEDRange? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:FORCEDRange value command.

SCPI Syntax

- AUXIn:PRObe:FORCEDRange <NR3>
- AUXIn:PRObe:FORCEDRange?

Info

<NR3> specifies the probe range.

AuxinProbeGain ¶

Bases: SCPICmdRead

The AUXIn:PRObe:GAIN command.

Description

This query-only command returns the gain factor of the probe that is attached to the AUX In input. The ‘gain’ of a probe is the output divided by the input transfer ratio. For example, a common 10x probe has a gain of 0.1.

Usage

Using the .query() method will send the AUXIn:PRObe:GAIN? query.
Using the .verify(value) method will send the AUXIn:PRObe:GAIN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:GAIN?

AuxinProbeId ¶

Bases: SCPICmdRead

The AUXIn:PRObe:ID command tree.

Usage

Using the .query() method will send the AUXIn:PRObe:ID? query.
Using the .verify(value) method will send the AUXIn:PRObe:ID? query and raise an AssertionError if the returned value does not match value.

Properties

.sernumber: The AUXIn:PRObe:ID:SERnumber command.
.type: The AUXIn:PRObe:ID:TYPe command.

sernumber `property` ¶

sernumber: AuxinProbeIdSernumber

Return the AUXIn:PRObe:ID:SERnumber command.

Description

This query-only command returns the probe serial number.

Usage

Using the .query() method will send the AUXIn:PRObe:ID:SERnumber? query.
Using the .verify(value) method will send the AUXIn:PRObe:ID:SERnumber? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:ID:SERnumber?

type `property` ¶

type: AuxinProbeIdType

Return the AUXIn:PRObe:ID:TYPe command.

Description

This query-only command returns the probe type.

Usage

Using the .query() method will send the AUXIn:PRObe:ID:TYPe? query.
Using the .verify(value) method will send the AUXIn:PRObe:ID:TYPe? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:ID:TYPe?

AuxinProbeIdSernumber ¶

Bases: SCPICmdRead

The AUXIn:PRObe:ID:SERnumber command.

Description

This query-only command returns the probe serial number.

Usage

Using the .query() method will send the AUXIn:PRObe:ID:SERnumber? query.
Using the .verify(value) method will send the AUXIn:PRObe:ID:SERnumber? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:ID:SERnumber?

AuxinProbeIdType ¶

Bases: SCPICmdRead

The AUXIn:PRObe:ID:TYPe command.

Description

This query-only command returns the probe type.

Usage

Using the .query() method will send the AUXIn:PRObe:ID:TYPe? query.
Using the .verify(value) method will send the AUXIn:PRObe:ID:TYPe? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:ID:TYPe?

AuxinProbeInputmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:INPUTMode command.

Description

This command sets or queries one of the probe’s four input modes on the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode {COMmonmode|DEFault|DIFFerential|A|B}
- AUXIn:PRObe:INPUTMode?

Info

COMmonmode sets the probe to route common-mode signals to the host.
DEFault sets the probe to the default mode.
DIFFerential sets the probe to route differential signals to the host.
A sets the probe to route single-ended A signals to the host.
B sets the probe to route single-ended B signals to the host.

Properties

.aoffset: The AUXIn:PRObe:INPUTMode:AOFFSet command.
.boffset: The AUXIn:PRObe:INPUTMode:BOFFSet command.
.cmoffset: The AUXIn:PRObe:INPUTMode:CMOFFSet command.
.dmoffset: The AUXIn:PRObe:INPUTMode:DMOFFSet command.

aoffset `property` ¶

aoffset: AuxinProbeInputmodeAoffset

Return the AUXIn:PRObe:INPUTMode:AOFFSet command.

Description

This command sets or queries the requested A mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:AOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:AOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:AOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:AOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:AOFFSet?

Info

<NR3> specifies the A mode offset control.

boffset `property` ¶

boffset: AuxinProbeInputmodeBoffset

Return the AUXIn:PRObe:INPUTMode:BOFFSet command.

Description

This command sets or queries the requested B mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:BOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:BOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:BOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:BOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:BOFFSet?

Info

<NR3> specifies the B mode offset control.

cmoffset `property` ¶

cmoffset: AuxinProbeInputmodeCmoffset

Return the AUXIn:PRObe:INPUTMode:CMOFFSet command.

Description

This command sets or queries the requested common mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:CMOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:CMOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:CMOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:CMOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:CMOFFSet?

Info

<NR3> specifies the common mode offset control.

dmoffset `property` ¶

dmoffset: AuxinProbeInputmodeDmoffset

Return the AUXIn:PRObe:INPUTMode:DMOFFSet command.

Description

This command sets or queries the requested differential mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:DMOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:DMOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:DMOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:DMOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:DMOFFSet?

Info

<NR3> specifies the differential mode offset control.

AuxinProbeInputmodeAoffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:INPUTMode:AOFFSet command.

Description

This command sets or queries the requested A mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:AOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:AOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:AOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:AOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:AOFFSet?

Info

<NR3> specifies the A mode offset control.

AuxinProbeInputmodeBoffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:INPUTMode:BOFFSet command.

Description

This command sets or queries the requested B mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:BOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:BOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:BOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:BOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:BOFFSet?

Info

<NR3> specifies the B mode offset control.

AuxinProbeInputmodeCmoffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:INPUTMode:CMOFFSet command.

Description

This command sets or queries the requested common mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:CMOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:CMOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:CMOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:CMOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:CMOFFSet?

Info

<NR3> specifies the common mode offset control.

AuxinProbeInputmodeDmoffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:INPUTMode:DMOFFSet command.

Description

This command sets or queries the requested differential mode offset control of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:INPUTMode:DMOFFSet? query.
Using the .verify(value) method will send the AUXIn:PRObe:INPUTMode:DMOFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:INPUTMode:DMOFFSet value command.

SCPI Syntax

- AUXIn:PRObe:INPUTMode:DMOFFSet <NR3>
- AUXIn:PRObe:INPUTMode:DMOFFSet?

Info

<NR3> specifies the differential mode offset control.

AuxinProbeRange ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:RANge command.

Description

This command controls or queries the set attenuation range of the probe on the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:RANge? query.
Using the .verify(value) method will send the AUXIn:PRObe:RANge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:RANge value command.

SCPI Syntax

- AUXIn:PRObe:RANge {ATTEN1X|ATTEN1_25X|ATTEN1_5X|ATTEN1_75X|ATTEN2X|ATTEN2_5X|ATTEN3X|ATTEN3_5X|ATTEN4X|ATTEN4_5X|ATTEN5X|ATTEN5_5X|ATTEN6X|ATTEN6_5X|ATTEN7X|ATTEN7_5X|ATTEN8X|ATTEN8_5X|ATTEN9X|ATTEN9_5X|ATTEN10X|ATTEN12_5X|ATTEN15X|ATTEN17_5X|ATTEN20X|ATTEN25X|ATTEN30X|ATTEN35X|ATTEN40X|ATTEN45X|ATTEN50X|ATTEN55X|ATTEN60X|ATTEN65X|ATTEN70X|ATTEN75X|ATTEN80X|ATTEN85X|ATTEN90X|ATTEN95X|ATTEN100X|ATTEN125X|ATTEN150X|ATTEN175X|ATTEN200X|ATTEN250X|ATTEN300X|ATTEN350X|ATTEN400X|ATTEN450X|ATTEN500X|ATTEN550X|ATTEN600X|ATTEN650X|ATTEN700X|ATTEN750X|ATTEN800X|ATTEN850X|ATTEN900X|ATTEN950X|ATTEN1000X}
- AUXIn:PRObe:RANge?

AuxinProbeResistance ¶

Bases: SCPICmdRead

The AUXIn:PRObe:RESistance command.

Description

This query-only command returns the resistance factor of the probe that is attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:RESistance? query.
Using the .verify(value) method will send the AUXIn:PRObe:RESistance? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:RESistance?

AuxinProbeSet ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:SET command.

Description

This command sets or queries aspects of probe accessory user interfaces, for example probe attenuation factors. The available arguments for this command will vary depending on the accessory you attach to the instrument auxiliary trigger input. For the P7260 probe, you can select between two attenuation factors using either this GPIB command or the push switch on the probe. The probe enables the relevant path and adjusts the settings based on the characteristics of the path in use. The probe signal path selection is not kept in persistent storage. The probe will lose the selection if you reboot the instrument or remove the probe. Also, the instrument does not store the selection in the save/recall setup operation.

Usage

Using the .query() method will send the AUXIn:PRObe:SET? query.
Using the .verify(value) method will send the AUXIn:PRObe:SET? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:SET value command.

SCPI Syntax

- AUXIn:PRObe:SET <QString>
- AUXIn:PRObe:SET?

Info

<QString> is a quoted string representing a settable aspect of the attached accessory.
ATTENUATION 5X sets the P7260 probe to ±0.75 V dynamic range with 6 GHz bandwidth and 5X attenuation.
ATTENUATION 25X sets the P7260 probe to ±3 V dynamic range with 6 GHz bandwidth and 25X attenuation.
VTERMsource AUTO sets the P7380SMA probe voltage termination source to auto.
VTERMsource INTernal sets the P7380SMA probe voltage termination source to internal.
VTERMsource EXTernal sets the P7380SMA probe voltage termination source to external.

AuxinProbeSignal ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:SIGnal command.

Description

This command sets or queries aspects of probe accessory user interfaces. The available arguments for this command will vary depending on the accessory you attach to the instrument.

Usage

Using the .query() method will send the AUXIn:PRObe:SIGnal? query.
Using the .verify(value) method will send the AUXIn:PRObe:SIGnal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:SIGnal value command.

SCPI Syntax

- AUXIn:PRObe:SIGnal {PASS|BYPass}
- AUXIn:PRObe:SIGnal?

Info

PASS opens a relay passing your signal to the instrument.
BYPass closes a relay preventing your signal from reaching the instrument. During probe degauss, the signal should be bypassed.

AuxinProbeTiptype ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PRObe:TIPtype command.

Description

This command sets or queries the type of probe tip being used.

Usage

Using the .query() method will send the AUXIn:PRObe:TIPtype? query.
Using the .verify(value) method will send the AUXIn:PRObe:TIPtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PRObe:TIPtype value command.

SCPI Syntax

- AUXIn:PRObe:TIPtype {HBWStraightflex|OTHer}
- AUXIn:PRObe:TIPtype?

Info

HBWStraightflex lets the instrument know you are using a high bandwidth straight-flex probe tip.
OTHer lets the instrument know you are not using a high bandwidth straight-flex probe tip.

AuxinProbeUnits ¶

Bases: SCPICmdRead

The AUXIn:PRObe:UNIts command.

Description

This query-only command returns a string describing the units of measure for the probe attached to the AUX In input.

Usage

Using the .query() method will send the AUXIn:PRObe:UNIts? query.
Using the .verify(value) method will send the AUXIn:PRObe:UNIts? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- AUXIn:PRObe:UNIts?

AuxinProbefunc ¶

Bases: SCPICmdRead

The AUXIn:PROBEFunc command tree.

Usage

Using the .query() method will send the AUXIn:PROBEFunc? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc? query and raise an AssertionError if the returned value does not match value.

Properties

.extatten: The AUXIn:PROBEFunc:EXTAtten command.
.extdbatten: The AUXIn:PROBEFunc:EXTDBatten command.
.extunits: The AUXIn:PROBEFunc:EXTUnits command.

extatten `property` ¶

extatten: AuxinProbefuncExtatten

Return the AUXIn:PROBEFunc:EXTAtten command.

Description

This command sets the input-output ratio, of external attenuation or gain, between the signal and the AUX In input. The query form of this command returns the user-specified attenuation. Note that this command deals with an attenuation factor, not a gain factor, unlike CHX:PROBE (This command returns a value independent of the external attenuation). For example, if you specify a 20X attenuation factor, the commands return the following values (assuming that a 1x probe is presently attached, since the external attenuation is used in combination with the probe attenuation): AUXIN:PROBE:EXTA? 20.00E+0 AUXIN:PROBE? 1.0E+0 This command is equivalent to selecting Attenuation from the Vertical menu, and then either viewing or setting Ext Atten.

Usage

Using the .query() method will send the AUXIn:PROBEFunc:EXTAtten? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc:EXTAtten? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PROBEFunc:EXTAtten value command.

SCPI Syntax

- AUXIn:PROBEFunc:EXTAtten <NR3>
- AUXIn:PROBEFunc:EXTAtten?

Info

<NR3> is the attenuation value, which is specified as a multiplier in the range from 1.00E-10 to 1.00E+10.

extdbatten `property` ¶

extdbatten: AuxinProbefuncExtdbatten

Return the AUXIn:PROBEFunc:EXTDBatten command.

Description

This command sets the input-output ratio (expressed in decibel units) of external attenuation or gain between the signal and the instrument AUX In input. The query form of this command returns the user-specified attenuation in decibels: 1X = 0 dB, 10X = 20 dB, 100X = 40 dB, and similar things. This command is equivalent to selecting Attenuation from the Vertical menu, and then either viewing or setting Ext Att(dB).

Usage

Using the .query() method will send the AUXIn:PROBEFunc:EXTDBatten? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc:EXTDBatten? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PROBEFunc:EXTDBatten value command.

SCPI Syntax

- AUXIn:PROBEFunc:EXTDBatten <NR3>
- AUXIn:PROBEFunc:EXTDBatten?

Info

<NR3> is the attenuation value, which is specified in the range from -200.00 dB to 200.00 dB.

extunits `property` ¶

extunits: AuxinProbefuncExtunits

Return the AUXIn:PROBEFunc:EXTUnits command.

Description

This command sets the unit of measurement for the external attenuator of the AUX In input. There is also a corresponding query that returns the user-specified unit of measurement for the external attenuator. Unless these units are set to the factory default string value of ‘None’, they become the attenuated units of measurement for the input. It is assumed that the probe connected to the input is of the correct type to receive the output of the user’s external transducer or network.

Usage

Using the .query() method will send the AUXIn:PROBEFunc:EXTUnits? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc:EXTUnits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PROBEFunc:EXTUnits value command.

SCPI Syntax

- AUXIn:PROBEFunc:EXTUnits <QString>
- AUXIn:PROBEFunc:EXTUnits?

Info

<QString> can contain a string of up to eight characters to indicate the attenuation unit of measurement for the AUX In input. However, most instrument attenuators only display the first two characters.

AuxinProbefuncExtatten ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PROBEFunc:EXTAtten command.

Description

This command sets the input-output ratio, of external attenuation or gain, between the signal and the AUX In input. The query form of this command returns the user-specified attenuation. Note that this command deals with an attenuation factor, not a gain factor, unlike CHX:PROBE (This command returns a value independent of the external attenuation). For example, if you specify a 20X attenuation factor, the commands return the following values (assuming that a 1x probe is presently attached, since the external attenuation is used in combination with the probe attenuation): AUXIN:PROBE:EXTA? 20.00E+0 AUXIN:PROBE? 1.0E+0 This command is equivalent to selecting Attenuation from the Vertical menu, and then either viewing or setting Ext Atten.

Usage

Using the .query() method will send the AUXIn:PROBEFunc:EXTAtten? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc:EXTAtten? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PROBEFunc:EXTAtten value command.

SCPI Syntax

- AUXIn:PROBEFunc:EXTAtten <NR3>
- AUXIn:PROBEFunc:EXTAtten?

Info

<NR3> is the attenuation value, which is specified as a multiplier in the range from 1.00E-10 to 1.00E+10.

AuxinProbefuncExtdbatten ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PROBEFunc:EXTDBatten command.

Description

This command sets the input-output ratio (expressed in decibel units) of external attenuation or gain between the signal and the instrument AUX In input. The query form of this command returns the user-specified attenuation in decibels: 1X = 0 dB, 10X = 20 dB, 100X = 40 dB, and similar things. This command is equivalent to selecting Attenuation from the Vertical menu, and then either viewing or setting Ext Att(dB).

Usage

Using the .query() method will send the AUXIn:PROBEFunc:EXTDBatten? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc:EXTDBatten? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PROBEFunc:EXTDBatten value command.

SCPI Syntax

- AUXIn:PROBEFunc:EXTDBatten <NR3>
- AUXIn:PROBEFunc:EXTDBatten?

Info

<NR3> is the attenuation value, which is specified in the range from -200.00 dB to 200.00 dB.

AuxinProbefuncExtunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:PROBEFunc:EXTUnits command.

Description

This command sets the unit of measurement for the external attenuator of the AUX In input. There is also a corresponding query that returns the user-specified unit of measurement for the external attenuator. Unless these units are set to the factory default string value of ‘None’, they become the attenuated units of measurement for the input. It is assumed that the probe connected to the input is of the correct type to receive the output of the user’s external transducer or network.

Usage

Using the .query() method will send the AUXIn:PROBEFunc:EXTUnits? query.
Using the .verify(value) method will send the AUXIn:PROBEFunc:EXTUnits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:PROBEFunc:EXTUnits value command.

SCPI Syntax

- AUXIn:PROBEFunc:EXTUnits <QString>
- AUXIn:PROBEFunc:EXTUnits?

Info

<QString> can contain a string of up to eight characters to indicate the attenuation unit of measurement for the AUX In input. However, most instrument attenuators only display the first two characters.

AuxinVterm ¶

Bases: SCPICmdRead

The AUXIn:VTERm command tree.

Usage

Using the .query() method will send the AUXIn:VTERm? query.
Using the .verify(value) method will send the AUXIn:VTERm? query and raise an AssertionError if the returned value does not match value.

Properties

.dual: The AUXIn:VTERm:DUAL command tree.

dual `property` ¶

dual: AuxinVtermDual

Return the AUXIn:VTERm:DUAL command tree.

Usage

Using the .query() method will send the AUXIn:VTERm:DUAL? query.
Using the .verify(value) method will send the AUXIn:VTERm:DUAL? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.a: The AUXIn:VTERm:DUAL:A command.
.b: The AUXIn:VTERm:DUAL:B command.

AuxinVtermDual ¶

Bases: SCPICmdRead

The AUXIn:VTERm:DUAL command tree.

Usage

Using the .query() method will send the AUXIn:VTERm:DUAL? query.
Using the .verify(value) method will send the AUXIn:VTERm:DUAL? query and raise an AssertionError if the returned value does not match value.

Properties

.a: The AUXIn:VTERm:DUAL:A command.
.b: The AUXIn:VTERm:DUAL:B command.

a `property` ¶

a: AuxinVtermDualA

Return the AUXIn:VTERm:DUAL:A command.

Description

This command sets or queries the termination voltage for probes with dual inputs that support settable termination voltage.

Usage

Using the .query() method will send the AUXIn:VTERm:DUAL:A? query.
Using the .verify(value) method will send the AUXIn:VTERm:DUAL:A? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:VTERm:DUAL:A value command.

SCPI Syntax

- AUXIn:VTERm:DUAL:A <NR3>
- AUXIn:VTERm:DUAL:A?

Info

<NR3> specifies the termination voltage.

b `property` ¶

b: AuxinVtermDualB

Return the AUXIn:VTERm:DUAL:B command.

Description

This command sets or queries the termination voltage for probes with dual inputs that support settable termination voltage.

Usage

Using the .query() method will send the AUXIn:VTERm:DUAL:B? query.
Using the .verify(value) method will send the AUXIn:VTERm:DUAL:B? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:VTERm:DUAL:B value command.

SCPI Syntax

- AUXIn:VTERm:DUAL:B <NR3>
- AUXIn:VTERm:DUAL:B?

Info

<NR3> specifies the termination voltage.

AuxinVtermDualA ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:VTERm:DUAL:A command.

Description

This command sets or queries the termination voltage for probes with dual inputs that support settable termination voltage.

Usage

Using the .query() method will send the AUXIn:VTERm:DUAL:A? query.
Using the .verify(value) method will send the AUXIn:VTERm:DUAL:A? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:VTERm:DUAL:A value command.

SCPI Syntax

- AUXIn:VTERm:DUAL:A <NR3>
- AUXIn:VTERm:DUAL:A?

Info

<NR3> specifies the termination voltage.

AuxinVtermDualB ¶

Bases: SCPICmdWrite, SCPICmdRead

The AUXIn:VTERm:DUAL:B command.

Description

This command sets or queries the termination voltage for probes with dual inputs that support settable termination voltage.

Usage

Using the .query() method will send the AUXIn:VTERm:DUAL:B? query.
Using the .verify(value) method will send the AUXIn:VTERm:DUAL:B? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the AUXIn:VTERm:DUAL:B value command.

SCPI Syntax

- AUXIn:VTERm:DUAL:B <NR3>
- AUXIn:VTERm:DUAL:B?

Info

<NR3> specifies the termination voltage.

auxin ¶

Auxin ¶

bandwidth property ¶

coupling property ¶

offset property ¶

probe property ¶

probefunc property ¶

vterm property ¶

AuxinBandwidth ¶

AuxinCoupling ¶

AuxinOffset ¶

AuxinProbe ¶

autozero property ¶

degauss property ¶

forcedrange property ¶

gain property ¶

id property ¶

inputmode property ¶

range property ¶

resistance property ¶

set_ property ¶

signal property ¶

tiptype property ¶

units property ¶

AuxinProbeAutozero ¶

AuxinProbeDegauss ¶

state property ¶

AuxinProbeDegaussState ¶

AuxinProbeForcedrange ¶

AuxinProbeGain ¶

AuxinProbeId ¶

sernumber property ¶

type property ¶

AuxinProbeIdSernumber ¶

AuxinProbeIdType ¶

AuxinProbeInputmode ¶

aoffset property ¶

boffset property ¶

cmoffset property ¶

dmoffset property ¶

AuxinProbeInputmodeAoffset ¶

AuxinProbeInputmodeBoffset ¶

AuxinProbeInputmodeCmoffset ¶

AuxinProbeInputmodeDmoffset ¶

AuxinProbeRange ¶

AuxinProbeResistance ¶

AuxinProbeSet ¶

AuxinProbeSignal ¶

AuxinProbeTiptype ¶

AuxinProbeUnits ¶

AuxinProbefunc ¶

extatten property ¶

extdbatten property ¶

extunits property ¶

AuxinProbefuncExtatten ¶

AuxinProbefuncExtdbatten ¶

AuxinProbefuncExtunits ¶

AuxinVterm ¶

dual property ¶

AuxinVtermDual ¶

a property ¶

b property ¶

AuxinVtermDualA ¶

AuxinVtermDualB ¶

bandwidth `property` ¶

coupling `property` ¶

offset `property` ¶

probe `property` ¶

probefunc `property` ¶

vterm `property` ¶

autozero `property` ¶

degauss `property` ¶

forcedrange `property` ¶

gain `property` ¶

id `property` ¶

inputmode `property` ¶

range `property` ¶

resistance `property` ¶

set_ `property` ¶

signal `property` ¶

tiptype `property` ¶

units `property` ¶

state `property` ¶

sernumber `property` ¶

type `property` ¶

aoffset `property` ¶

boffset `property` ¶

cmoffset `property` ¶

dmoffset `property` ¶

extatten `property` ¶

extdbatten `property` ¶

extunits `property` ¶

dual `property` ¶

a `property` ¶

b `property` ¶