The measurement commands module.
These commands are used in the following models: TekScopePC
THIS FILE IS AUTO-GENERATED, IT SHOULD NOT BE MANUALLY MODIFIED.
Please report an issue if one is found.
Commands and Queries
- MEASUrement:ADDMEAS {ACCOMMONMODE|ACRMS|AMPlITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|CCJITTER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HEIGHT|HEIGHTBER|HIGH|HIGHTIME|HOLD|IMDAPOWERQUALITY|IMDAHARMONICS|IMDAINPUTVOLTAGE|IMDAINPUTCURRENT|IMDAINPUTPOWER|IMDAPHASORDIAGRAM|IMDAEFFICIENCY|IMDALINERIPPLE|IMDASWITCHRIPPLE|IMDADQ0|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NPJ|NWIDTTH|PDUTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SETUP|SKEW|SRJ|SSCFREQDEV|SSCMODRATE|TIE|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WIDTH|WIDTHBER}
- MEASUrement:ADDNew 'QString'
- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?
- MEASUrement:AUTOset {EXECute|THREEPHASEAUTOset|WBGPREset|DPMAutoset|DPMPReset}
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?
- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?
- MEASUrement:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:CLOCKRecovery:ADVanced:METHod?
- MEASUrement:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:CLOCKRecovery:CLOCKFrequency?
- MEASUrement:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:CLOCKRecovery:CLOCKMultiplier?
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe?
- MEASUrement:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:CLOCKRecovery:DAMPing?
- MEASUrement:CLOCKRecovery:DATAPath <QString>
- MEASUrement:CLOCKRecovery:DATAPath?
- MEASUrement:CLOCKRecovery:DATARate <NR3>
- MEASUrement:CLOCKRecovery:DATARate?
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?
- MEASUrement:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:CLOCKRecovery:JTFBandwidth?
- MEASUrement:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:CLOCKRecovery:LOOPBandwidth?
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate?
- MEASUrement:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:CLOCKRecovery:METHod?
- MEASUrement:CLOCKRecovery:MODel {TYPE<x>}
- MEASUrement:CLOCKRecovery:MODel?
- MEASUrement:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
- MEASUrement:CLOCKRecovery:NOMINALOFFset?
- MEASUrement:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:CLOCKRecovery:STAndard?
- MEASUrement:DELETEALL
- MEASUrement:DELete <QString>
- MEASUrement:DIRacmodel {PCIExpress|FIBREchannel}
- MEASUrement:DIRacmodel?
- MEASUrement:DISPLAYUnits {SEConds|UNITINtervals}
- MEASUrement:DISPLAYUnits?
- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:EYERENDER {ON|OFF|<NR1>}
- MEASUrement:EYERENDER?
- MEASUrement:FILTers:BLANKingtime <NR3>
- MEASUrement:FILTers:BLANKingtime?
- MEASUrement:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:FILTers:HIGHPass:FREQ?
- MEASUrement:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:HIGHPass:SPEC?
- MEASUrement:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:FILTers:LOWPass:FREQ?
- MEASUrement:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:LOWPass:SPEC?
- MEASUrement:FILTers:RAMPtime <NR3>
- MEASUrement:FILTers:RAMPtime?
- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?
- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?
- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?
- MEASUrement:GATing:LOGICSource {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?
- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?
- MEASUrement:GATing:SEARCHSource SEARCH1
- MEASUrement:GATing:SEARCHSource?
- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?
- MEASUrement:GATing?
- MEASUrement:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:HIGHLEVel:CONFIGuration?
- MEASUrement:HIGHLEVel:EDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:EDGEQUALifier?
- MEASUrement:HIGHLEVel:INLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:INLOWPass:FREQ?
- MEASUrement:HIGHLEVel:INLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:INLOWPass:SPEC?
- MEASUrement:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:L2LTOL2N?
- MEASUrement:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:HIGHLEVel:LINESelected?
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier?
- MEASUrement:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:OUTL2LTOL2N?
- MEASUrement:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:HIGHLEVel:OUTLINESelected?
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ?
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC?
- MEASUrement:HIGHLEVel:OUTSOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTSOURCE?
- MEASUrement:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:HIGHLEVel:OUTWIRing?
- MEASUrement:HIGHLEVel:SOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:SOURCE?
- MEASUrement:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:WIRing?
- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?
- MEASUrement:JITTermodel {SPECTRAL|SPECTRALBUJ}
- MEASUrement:JITTermodel?
- MEASUrement:LIST?
- MEASUrement:LOCKRJ {ON|OFF|<NR1>}
- MEASUrement:LOCKRJ?
- MEASUrement:LOCKRJValue <NR3>
- MEASUrement:LOCKRJValue?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?
- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?
- MEASUrement:MEAS<x>:BER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER?
- MEASUrement:MEAS<x>:BER?
- MEASUrement:MEAS<x>:BIN <NR3>
- MEASUrement:MEAS<x>:BIN?
- MEASUrement:MEAS<x>:BITCfgmode {MEAN|MODE}
- MEASUrement:MEAS<x>:BITCfgmode?
- MEASUrement:MEAS<x>:BITEnd <NR3>
- MEASUrement:MEAS<x>:BITEnd?
- MEASUrement:MEAS<x>:BITPcnt <NR3>
- MEASUrement:MEAS<x>:BITPcnt?
- MEASUrement:MEAS<x>:BITSTart <NR3>
- MEASUrement:MEAS<x>:BITSTart?
- MEASUrement:MEAS<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- MEASUrement:MEAS<x>:BITType?
- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?
- MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath <QString>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate?
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod?
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel {TYPE<x>}
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel?
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?
- MEASUrement:MEAS<x>:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs {SINGLE|DOUBLE}
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs?
- MEASUrement:MEAS<x>:COVer {FFREQuency|AFREQuencies}
- MEASUrement:MEAS<x>:COVer?
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile <Qstring>
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile?
- MEASUrement:MEAS<x>:CYCLemode {RECORD|CYCLE}
- MEASUrement:MEAS<x>:CYCLemode?
- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?
- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?
- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?
- MEASUrement:MEAS<x>:EDGEQUALONE <Qstring>
- MEASUrement:MEAS<x>:EDGEQUALONE?
- MEASUrement:MEAS<x>:EDGEQUALTWO <Qstring>
- MEASUrement:MEAS<x>:EDGEQUALTWO?
- MEASUrement:MEAS<x>:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:EDGEQUALifier?
- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?
- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency?
- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?
- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency?
- MEASUrement:MEAS<x>:EEQUal {ON|OFF}
- MEASUrement:MEAS<x>:EEQUal?
- MEASUrement:MEAS<x>:FAILCount?
- MEASUrement:MEAS<x>:FILTERRANGEFROM <NR3>
- MEASUrement:MEAS<x>:FILTERRANGEFROM?
- MEASUrement:MEAS<x>:FILTERRANGETO <NR3>
- MEASUrement:MEAS<x>:FILTERRANGETO?
- MEASUrement:MEAS<x>:FILTers:BLANKingtime <NR3>
- MEASUrement:MEAS<x>:FILTers:BLANKingtime?
- MEASUrement:MEAS<x>:FILTers:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:FILTers:GLOBal?
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?
- MEASUrement:MEAS<x>:FILTers:RAMPtime <NR3>
- MEASUrement:MEAS<x>:FILTers:RAMPtime?
- MEASUrement:MEAS<x>:FREQ <NR3>
- MEASUrement:MEAS<x>:FREQ?
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?
- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?
- MEASUrement:MEAS<x>:FUNDCURRent <NR3>
- MEASUrement:MEAS<x>:FUNDCURRent?
- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?
- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?
- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?
- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?
- MEASUrement:MEAS<x>:GATing:LOGICSource {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?
- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?
- MEASUrement:MEAS<x>:GATing?
- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?
- MEASUrement:MEAS<x>:HARMONICSCLass {CLASSA|CLASSB|CLASSC|CLASSD}
- MEASUrement:MEAS<x>:HARMONICSCLass?
- MEASUrement:MEAS<x>:HARMONICSSOURce {CURRENT|VOLTAGE}
- MEASUrement:MEAS<x>:HARMONICSSOURce?
- MEASUrement:MEAS<x>:HARMONICSStd {NONE|IEC|IEEE519|CUSTOM}
- MEASUrement:MEAS<x>:HARMONICSStd?
- MEASUrement:MEAS<x>:HARMONICSUNits {LOGARITHM|LINEAR}
- MEASUrement:MEAS<x>:HARMONICSUNits?
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected?
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL {ON|OFF|1|0}
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing?
- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal {ON|OFF}
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?
- MEASUrement:MEAS<x>:HTORque <NR1>
- MEASUrement:MEAS<x>:HTORque?
- MEASUrement:MEAS<x>:HVOLtage <NR1>
- MEASUrement:MEAS<x>:HVOLtage?
- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?
- MEASUrement:MEAS<x>:INPUTLEVel <NR2>
- MEASUrement:MEAS<x>:INPUTLEVel?
- MEASUrement:MEAS<x>:INPUTPOwer <NR3>
- MEASUrement:MEAS<x>:INPUTPOwer?
- MEASUrement:MEAS<x>:JITTERSummary:DCD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DCD?
- MEASUrement:MEAS<x>:JITTERSummary:DDJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DDJ?
- MEASUrement:MEAS<x>:JITTERSummary:DJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJDD?
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?
- MEASUrement:MEAS<x>:JITTERSummary:NPJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:NPJ?
- MEASUrement:MEAS<x>:JITTERSummary:PJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PJ?
- MEASUrement:MEAS<x>:JITTERSummary:RJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJDD?
- MEASUrement:MEAS<x>:JITTERSummary:TIE {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TIE?
- MEASUrement:MEAS<x>:JITTERSummary:TJBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TJBER?
- MEASUrement:MEAS<x>:LABel <QString>
- MEASUrement:MEAS<x>:LINESelected {ABCB|ACBC|BACA|XYZY|XZYZ|YXZX}
- MEASUrement:MEAS<x>:LINESelected?
- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?
- MEASUrement:MEAS<x>:LTORque <NR1>
- MEASUrement:MEAS<x>:LTORque?
- MEASUrement:MEAS<x>:LTYPe {AUTO|CUSTom}
- MEASUrement:MEAS<x>:LTYPe?
- MEASUrement:MEAS<x>:LUNITs {PERCent|ABSolute}
- MEASUrement:MEAS<x>:LUNITs?
- MEASUrement:MEAS<x>:LVOLtage <NR1>
- MEASUrement:MEAS<x>:LVOLtage?
- MEASUrement:MEAS<x>:MAXCUrrent <NR3>
- MEASUrement:MEAS<x>:MAXCUrrent?
- MEASUrement:MEAS<x>:MAXCycle <NR1>
- MEASUrement:MEAS<x>:MAXCycle?
- MEASUrement:MEAS<x>:MAXGVoltage <NR3>
- MEASUrement:MEAS<x>:MAXGVoltage?
- MEASUrement:MEAS<x>:MAXVoltage <NR2>
- MEASUrement:MEAS<x>:MAXVoltage?
- MEASUrement:MEAS<x>:MEASRange:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:GLOBal?
- MEASUrement:MEAS<x>:MEASRange:MAX <NR3>
- MEASUrement:MEAS<x>:MEASRange:MAX?
- MEASUrement:MEAS<x>:MEASRange:MIN <NR3>
- MEASUrement:MEAS<x>:MEASRange:MIN?
- MEASUrement:MEAS<x>:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:STATE?
- MEASUrement:MEAS<x>:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MECH:EINDexz?
- MEASUrement:MEAS<x>:MECH:GRATio <NR3>
- MEASUrement:MEAS<x>:MECH:GRATio?
- MEASUrement:MEAS<x>:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MEAS<x>:MECH:MUNits?
- MEASUrement:MEAS<x>:MECH:PPAirs <NR1>
- MEASUrement:MEAS<x>:MECH:PPAirs?
- MEASUrement:MEAS<x>:MECH:PPRotation <NR1>
- MEASUrement:MEAS<x>:MECH:PPRotation?
- MEASUrement:MEAS<x>:MECH:STYPe {HSENSOR|QEI}
- MEASUrement:MEAS<x>:MECH:STYPe?
- MEASUrement:MEAS<x>:MINCycle <NR1>
- MEASUrement:MEAS<x>:MINCycle?
- MEASUrement:MEAS<x>:ODDEVen {ALL|EVEN|ODD}
- MEASUrement:MEAS<x>:ODDEVen?
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?
- MEASUrement:MEAS<x>:OSANgle <NR1>
- MEASUrement:MEAS<x>:OSANgle?
- MEASUrement:MEAS<x>:OUTEDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:OUTEDGEQUALifier?
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ <NR2>
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?
- MEASUrement:MEAS<x>:OUTPUT<n>VOLTage <NR2>
- MEASUrement:MEAS<x>:OUTPUT<n>VOLTage?
- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?
- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?
- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?
- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?
- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?
- MEASUrement:MEAS<x>:PATTERNDETECTION {AUTO|MANUAL}
- MEASUrement:MEAS<x>:PATTERNDETECTION?
- MEASUrement:MEAS<x>:PATTERNLENgth <NR3>
- MEASUrement:MEAS<x>:PATTERNLENgth?
- MEASUrement:MEAS<x>:PATTERNTYPe {REPeating|ARBitrary}
- MEASUrement:MEAS<x>:PATTERNTYPe?
- MEASUrement:MEAS<x>:PCOUNt <NR3>
- MEASUrement:MEAS<x>:PCOUNt?
- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?
- MEASUrement:MEAS<x>:POPUlation:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:GLOBal?
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue <NR3>
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?
- MEASUrement:MEAS<x>:POWERFACtor <NR2>
- MEASUrement:MEAS<x>:POWERFACtor?
- MEASUrement:MEAS<x>:PREGion {FPULse|SPULse|MPULse}
- MEASUrement:MEAS<x>:PREGion?
- MEASUrement:MEAS<x>:PWIDth <NR3>
- MEASUrement:MEAS<x>:PWIDth?
- MEASUrement:MEAS<x>:REDGe {ON|OFF}
- MEASUrement:MEAS<x>:REDGe?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?
- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?
- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?
- MEASUrement:MEAS<x>:REFVOLTAGE<n>Val <NR2>
- MEASUrement:MEAS<x>:REFVOLTAGE<n>Val?
- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?
- MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?
- MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?
- MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?
- MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val <NR3>
- MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val?
- MEASUrement:MEAS<x>:SEQuence {ABC|ACB}
- MEASUrement:MEAS<x>:SEQuence?
- MEASUrement:MEAS<x>:SIGNALFREQUEncy {AUTO|FIFTYHZ|SIXTYHZ|FOURHUNDREDHZ|CUSTOM}
- MEASUrement:MEAS<x>:SIGNALFREQUEncy?
- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?
- MEASUrement:MEAS<x>:SLABs <NR3>
- MEASUrement:MEAS<x>:SLABs?
- MEASUrement:MEAS<x>:SLPCt <NR3>
- MEASUrement:MEAS<x>:SLPCt?
- MEASUrement:MEAS<x>:SLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:SLTYpe?
- MEASUrement:MEAS<x>:SMOOTHINGFILTER <NR1>
- MEASUrement:MEAS<x>:SOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOURCE?
- MEASUrement:MEAS<x>:SOUrce1 {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOUrce1?
- MEASUrement:MEAS<x>:SSC:NOMinalfreq <NR3>
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANual}
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?
- MEASUrement:MEAS<x>:SSC:NOMinalfreq?
- MEASUrement:MEAS<x>:STATUS?
- MEASUrement:MEAS<x>:STLABs <NR3>
- MEASUrement:MEAS<x>:STLABs?
- MEASUrement:MEAS<x>:STLPct <NR3>
- MEASUrement:MEAS<x>:STLPct?
- MEASUrement:MEAS<x>:STLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:STLTYpe?
- MEASUrement:MEAS<x>:STYPe {VOLTage|CURRent}
- MEASUrement:MEAS<x>:STYPe?
- MEASUrement:MEAS<x>:SUNits {RPM|HZ}
- MEASUrement:MEAS<x>:SUNits?
- MEASUrement:MEAS<x>:TCKAVG <NR3>
- MEASUrement:MEAS<x>:TCKAVG?
- MEASUrement:MEAS<x>:TCONstant <NR1>
- MEASUrement:MEAS<x>:TCONstant?
- MEASUrement:MEAS<x>:TIMINGMode {EACHCLOCKCYCLE|TWOCLOCKCYCLES}
- MEASUrement:MEAS<x>:TIMINGMode?
- MEASUrement:MEAS<x>:TMEThod {SENSOR|CURRENT}
- MEASUrement:MEAS<x>:TMEThod?
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?
- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?
- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:TYPe {ACCOMMONMODE|ACRMS|AMPlITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMOVERSHOOT|DPMUNDERSHOOT|DPMRIPPLE|DPMTURNOFFTIME|DPMTURNONTIME|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HIGH|HEIGHT|HEIGHTBER|HIGHTIME|HOLD|IMDAPOWERQUALITY|IMDAHARMONICS|IMDAINPUTVOLTAGE|IMDAINPUTCURRENT|IMDAINPUTPOWER|IMDAPHASORDIAGRAM|IMDAEFFICIENCY|IMDALINERIPPLE|IMDASWITCHRIPPLE|IMDADQ0|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NPJ|NOVERSHOOT|NWIDTH|PDUTTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SRJ|SSCFREQDEV|SSCMODRATE|SETUP|SKEW|TIE|TIMEOUTSIDELEVEL|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WIDTH|WIDTHBER}
- MEASUrement:MEAS<x>:TYPe?
- MEASUrement:MEAS<x>:WAITTime <NR2>
- MEASUrement:MEAS<x>:WAITTime?
- MEASUrement:MEAS<x>:WINDOWLENgth <NR3>
- MEASUrement:MEAS<x>:WINDOWLENgth?
- MEASUrement:MEAS<x>:XUNIT?
- MEASUrement:MEAS<x>:YUNIT?
- MEASUrement:MEASRange:MAX <NR3>
- MEASUrement:MEASRange:MAX?
- MEASUrement:MEASRange:MIN <NR3>
- MEASUrement:MEASRange:MIN?
- MEASUrement:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEASRange:STATE?
- MEASUrement:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MECH:EINDexz?
- MEASUrement:MECH:GRATio <NR3>
- MEASUrement:MECH:GRATio?
- MEASUrement:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MECH:MUNits?
- MEASUrement:MECH:PPAirs <NR1>
- MEASUrement:MECH:PPAirs?
- MEASUrement:MECH:PPRotation <NR1>
- MEASUrement:MECH:PPRotation?
- MEASUrement:MECH:SOUrce1 {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>|CH<x>_D<x>}
- MEASUrement:MECH:SOUrce1?
- MEASUrement:MECH:STYPe {HSENSOR|QEI}
- MEASUrement:MECH:STYPe?
- MEASUrement:MINUI <NR3>
- MEASUrement:MINUI?
- MEASUrement:POPUlation:LIMIT:STATE {OFF|ON|0|1 }
- MEASUrement:POPUlation:LIMIT:STATE?
- MEASUrement:POPUlation:LIMIT:VALue <NR1>
- MEASUrement:POPUlation:LIMIT:VALue?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:REF<x>:REFLevels:BASETop
- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?
- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?
- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?
- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?
- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?
- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?
- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?
- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?
- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?
- MEASUrement:REFLevels:JITTERMODE {CONTinuous|LATCh}
- MEASUrement:REFLevels:JITTERMODE?
- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?
- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?
- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?
- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?
- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?
- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?
- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?
- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?
- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?
- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?
- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?
- MEASUrement:RESUlts:HISTory:STARt <NR1>
- MEASUrement:RESUlts:HISTory:STARt?
- MEASUrement:RESUlts:HISTory:STOP <NR1>
- MEASUrement:RESUlts:HISTory:STOP?
- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?
- MEASUrement:WBG:PDEVice {IGBT|MOSFET}
- MEASUrement:WBG:PDEVice?
- MEASUrement?
Bases: SCPICmdRead
The MEASUrement command.
Description
- This query-only command returns all measurement parameters.
Usage
- Using the
.query()method will send theMEASUrement?query. - Using the
.verify(value)method will send theMEASUrement?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement?
Properties
.addmeas: TheMEASUrement:ADDMEAScommand..addnew: TheMEASUrement:ADDNewcommand..annotate: TheMEASUrement:ANNOTatecommand..autoset: TheMEASUrement:AUTOsetcommand..ch: TheMEASUrement:CH<x>command tree..clockrecovery: TheMEASUrement:CLOCKRecoverycommand tree..deleteall: TheMEASUrement:DELETEALLcommand..delete: TheMEASUrement:DELetecommand..diracmodel: TheMEASUrement:DIRacmodelcommand..displayunits: TheMEASUrement:DISPLAYUnitscommand..edge: TheMEASUrement:EDGE<x>command..eyerender: TheMEASUrement:EYERENDERcommand..filters: TheMEASUrement:FILTerscommand tree..gating: TheMEASUrement:GATingcommand..highlevel: TheMEASUrement:HIGHLEVelcommand tree..interp: TheMEASUrement:INTERpcommand..jittermodel: TheMEASUrement:JITTermodelcommand..list: TheMEASUrement:LISTcommand..lockrj: TheMEASUrement:LOCKRJcommand..lockrjvalue: TheMEASUrement:LOCKRJValuecommand..math: TheMEASUrement:MATH<x>command tree..meas: TheMEASUrement:MEAS<x>command tree..measrange: TheMEASUrement:MEASRangecommand tree..mech: TheMEASUrement:MECHcommand tree..minui: TheMEASUrement:MINUIcommand..population: TheMEASUrement:POPUlationcommand tree..ref: TheMEASUrement:REF<x>command tree..reflevels: TheMEASUrement:REFLevelscommand tree..results: TheMEASUrement:RESUltscommand tree..statistics: TheMEASUrement:STATIsticscommand tree..wbg: TheMEASUrement:WBGcommand tree.
property
¶
addmeas: MeasurementAddmeas
Return the MEASUrement:ADDMEAS command.
Description
- This command adds a measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:ADDMEAS valuecommand.
SCPI Syntax
- MEASUrement:ADDMEAS {ACCOMMONMODE|ACRMS|AMPlITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|CCJITTER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HEIGHT|HEIGHTBER|HIGH|HIGHTIME|HOLD|IMDAPOWERQUALITY|IMDAHARMONICS|IMDAINPUTVOLTAGE|IMDAINPUTCURRENT|IMDAINPUTPOWER|IMDAPHASORDIAGRAM|IMDAEFFICIENCY|IMDALINERIPPLE|IMDASWITCHRIPPLE|IMDADQ0|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NPJ|NWIDTTH|PDUTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SETUP|SKEW|SRJ|SSCFREQDEV|SSCMODRATE|TIE|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WIDTH|WIDTHBER}
Info
ACCOMMONMODEAC Common Mode (Pk-Pk) is the peak-to-peak of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.ACRMS(AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.AMPLITUDEis the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.Amplitude = High - LowAREAis the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.BASEis the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.BITAMPLITUDE(Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITHIGH(Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITLOW(Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BURSTWIDTH(Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.COMMONMODE(DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.CCJITTER(Cycle-to-Cycle jitter) measures how much the clock period changes between any two adjacent cycles. Cycle-to-Cycle jitter is measured by applying a first order difference operation to the period jitter.DATARATE(Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.DCD(duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDJ(data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDRAOS(area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.DDRAOSPERTCK(area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAOSPERUI(area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRAUS(area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.DDRAUSPERTCK(area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAUSPERUI(area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRHOLDDIFF(hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.DDRSETUPDIFF(setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.DDRTCHABS(absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.DDRTCHAVERAGE(average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles. This measurement is made across the entire record.DDRTCKAVERAGE(average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles. This measurement is made across the entire record.DDRTCLABS(absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.DDRTCLAVERAGE(average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.DDRTERRMN(cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).DDRTERRN(cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).DDRTJITCC(cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.DDRTJITDUTY(half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.DDRTJITPER(clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.DDRTPST(read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.DDRTRPRE(read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRTWPREis the width of the Write burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRVIXACis the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.DDRTDQSCKis the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.DELayis the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.DJ(deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DJDIRAC(dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.EYEHIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.EYELOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.FALLSLEWRATE(Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.FALLTIME(Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.FREQuencyis the reciprocal of Period. This measurement is made on each cycle in the record.F2is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F4is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F8is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.HEIGHT(Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HEIGHTBER(Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGHTIME(High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.HOLD(Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.IMDAPOWERQUALITYmeasures the operating Frequency, RMS values of the voltage and current, Crest Factors of the voltage and current, Real Power, Reactive Power, Apparent Power, Power Factor, and Phase Angle of the AC signal. Plots the Phasor diagram. This measurement requires the IMDA option.IMDAHARMONICSmeasures the signal amplitudes at the fundamental line frequency and its harmonics. Measures the RMS amplitude and Total Harmonic Distortion of the signal. Plots the Harmonics Bar Graph. This measurement requires the IMDA option.IMDAINPUTVOLTAGEmeasures the RMS value of the input voltage for all phases based on the configured wiring. This measurement requires the IMDA option.IMDAINPUTCURRENTmeasures the RMS value of the input current for all phases based on the configured wiring. This measurement requires the IMDA option.IMDAINPUTPOWERmeasures the RMS and peak-to-peak values of the AC signal. This measurement requires the IMDA option.IMDAPHASORDIAGRAMplots Vrms and Irms and phase angles between voltage(s) and current(s) per winding pair. This measurement requires the IMDA option.IMDAEFFICIENCYmeasures the ratio of output power to input power per phase for a AC input and Drive output. Measures the total efficiency of the system. This measurement requires the IMDA option.IMDALINERIPPLEmeasures the RMS value of the input power for all phases based on the configured wiring. Measures the True / Apparent / Reactive Power for all the phases. This measurement requires the IMDA option.IMDASWITCHRIPPLEJITTERSUMMARYmeasures the RMS and peak-to-peak values of the switching signal. This measurement requires the IMDA option.IMDADQ0measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0.JITTERSUMMARY(Jitter Summary) is a group consisting of the following measurements: TIE, TJ@BER, Eye Width@BER, Eye Height@BER, RJ-δδ, DJ-δδ, PJ, DDJ, DcD, F/2, F/4, F/8. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J2is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J9is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.LOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.LOWTIME(Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.MAXimumis the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.MEANis the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.MINImumis the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.NDUty(Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.Negative Duty Cycle = (Negative Width) / Period × 100%NPERIOD(Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.NPJ(non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.NOVershoot(Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Negative Overshoot = (Base - Minimum) / Amplitude × 100%)NWIdth(Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.PDUTY(Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.Positive Duty Cycle = (Positive Width)/Period × 100%PERIODis the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.PHASEis the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.PHASENOISE(Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.PJ(periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.PK2Pk(Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.POVERSHOOT(Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Positive Overshoot = (Maximum - Top) / Amplitude ×100%PWIDTH(Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.QFACTOR(Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RISESLEWRATE(Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RISETIMERise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RJ(random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RJDIRAC(dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RMSis the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.SRJ(sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCFREQDEV(SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCMODRATE(SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SETUP(Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.SKEWSkew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.TIE(time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.TIMEOUTSIDELEVELTime Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.TIMETOMAXTime to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.TIMETOMINTime to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.TJBER(total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TNTRATIOT/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TOPis the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.UNITINTERVAL(Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.VDIFFXOVR(Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTH(Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTHBER(Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
property
¶
addnew: MeasurementAddnew
Return the MEASUrement:ADDNew command.
Description
- This command adds the specified measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:ADDNew valuecommand.
SCPI Syntax
- MEASUrement:ADDNew 'QString'
Info
'QString'is the measurement to add. The argument is of the form ‘MEAS’ where NR1 ≥ 1.
property
¶
annotate: MeasurementAnnotate
Return the MEASUrement:ANNOTate command.
Description
- This command sets or queries the annotation state for measurements.
Usage
- Using the
.query()method will send theMEASUrement:ANNOTate?query. - Using the
.verify(value)method will send theMEASUrement:ANNOTate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:ANNOTate valuecommand.
SCPI Syntax
- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?
Info
OFFturns off measurement annotations.AUTOturns on visible measurement annotations.
property
¶
autoset: MeasurementAutoset
Return the MEASUrement:AUTOset command.
Description
- This command performs an analysis jitter autoset.
Usage
- Using the
.write(value)method will send theMEASUrement:AUTOset valuecommand.
SCPI Syntax
- MEASUrement:AUTOset {EXECute|THREEPHASEAUTOset|WBGPREset|DPMAutoset|DPMPReset}
Info
EXECuteperforms an analysis jitter autoset.THREEPHASEAUTOsetperforms an IMDA 3 phase autoset.WBGPREsetperforms a measurement specific preset. Requires a WBG-DPT license.DPMAutosetperforms a power rail autoset. Requires option 5-DPM (5 Series MSO instruments) or 6-DPM (6 Series MSO instrument).DPMPResetperforms a power rail preset. Requires option 5-DPM (5 Series MSO instruments) or 6-DPM (6 Series MSO instrument).
property
¶
ch: dict[int, MeasurementChannel]
Return the MEASUrement:CH<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.reflevels: TheMEASUrement:CH<x>:REFLevelscommand tree.
property
¶
clockrecovery: MeasurementClockrecovery
Return the MEASUrement:CLOCKRecovery command tree.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.advanced: TheMEASUrement:CLOCKRecovery:ADVancedcommand tree..clockfrequency: TheMEASUrement:CLOCKRecovery:CLOCKFrequencycommand..clockmultiplier: TheMEASUrement:CLOCKRecovery:CLOCKMultipliercommand..constclockmode: TheMEASUrement:CLOCKRecovery:CONSTCLOCKMODecommand..damping: TheMEASUrement:CLOCKRecovery:DAMPingcommand..datapath: TheMEASUrement:CLOCKRecovery:DATAPathcommand..datarate: TheMEASUrement:CLOCKRecovery:DATARatecommand..explicitclockmode: TheMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODecommand..jtfbandwidth: TheMEASUrement:CLOCKRecovery:JTFBandwidthcommand..loopbandwidth: TheMEASUrement:CLOCKRecovery:LOOPBandwidthcommand..meanautocalculate: TheMEASUrement:CLOCKRecovery:MEANAUTOCalculatecommand..method: TheMEASUrement:CLOCKRecovery:METHodcommand..model: TheMEASUrement:CLOCKRecovery:MODelcommand..nominaloffset: TheMEASUrement:CLOCKRecovery:NOMINALOFFsetcommand..standard: TheMEASUrement:CLOCKRecovery:STAndardcommand.
property
¶
delete: MeasurementDelete
Return the MEASUrement:DELete command.
Description
- The command deletes the specified measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:DELete valuecommand.
SCPI Syntax
- MEASUrement:DELete <QString>
Info
<QString>is the measurement to delete. Argument is of the form ‘MEAS’ where is ≥1.
property
¶
deleteall: MeasurementDeleteall
Return the MEASUrement:DELETEALL command.
Description
- This command deletes all the active instances of measurements defined in the scope application.
Usage
- Using the
.write()method will send theMEASUrement:DELETEALLcommand.
SCPI Syntax
- MEASUrement:DELETEALL
property
¶
diracmodel: MeasurementDiracmodel
Return the MEASUrement:DIRacmodel command.
Description
- This command sets or queries the dirac model used to separate random from deterministic jitter for jitter measurements.
Usage
- Using the
.query()method will send theMEASUrement:DIRacmodel?query. - Using the
.verify(value)method will send theMEASUrement:DIRacmodel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:DIRacmodel valuecommand.
SCPI Syntax
- MEASUrement:DIRacmodel {PCIExpress|FIBREchannel}
- MEASUrement:DIRacmodel?
Info
PCIExpressspecifies the PCIExpress dirac model.FIBREchannelspecifies the FIBREchannel dirac model.
property
¶
displayunits: MeasurementDisplayunits
Return the MEASUrement:DISPLAYUnits command.
Description
- This command sets or queries the display units used for jitter summary measurements.
Usage
- Using the
.query()method will send theMEASUrement:DISPLAYUnits?query. - Using the
.verify(value)method will send theMEASUrement:DISPLAYUnits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:DISPLAYUnits valuecommand.
SCPI Syntax
- MEASUrement:DISPLAYUnits {SEConds|UNITINtervals}
- MEASUrement:DISPLAYUnits?
Info
SECondsset the display units to seconds.UNITINtervalsset the display units to unit intervals.
property
¶
edge: dict[int, MeasurementEdgeItem]
Return the MEASUrement:EDGE<x> command.
Description
- This command sets or queries the type of the edge for the measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:EDGE<x> valuecommand.
SCPI Syntax
- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
Info
FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both a rising and falling edge of the waveform.
property
¶
eyerender: MeasurementEyerender
Return the MEASUrement:EYERENDER command.
Description
- This command sets or queries the state of high-performance eye rendering for an eye diagram.
Usage
- Using the
.query()method will send theMEASUrement:EYERENDER?query. - Using the
.verify(value)method will send theMEASUrement:EYERENDER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:EYERENDER valuecommand.
SCPI Syntax
- MEASUrement:EYERENDER {ON|OFF|<NR1>}
- MEASUrement:EYERENDER?
Info
<NR1>= 0 disables high-performance eye rendering for an eye diagram; any other value turns this feature on.OFFdisables high-performance eye rendering for an eye diagram.ONenables high-performance eye rendering for an eye diagram.
property
¶
filters: MeasurementFilters
Return the MEASUrement:FILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:FILTers?query. - Using the
.verify(value)method will send theMEASUrement:FILTers?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.blankingtime: TheMEASUrement:FILTers:BLANKingtimecommand..highpass: TheMEASUrement:FILTers:HIGHPasscommand tree..lowpass: TheMEASUrement:FILTers:LOWPasscommand tree..ramptime: TheMEASUrement:FILTers:RAMPtimecommand.
property
¶
gating: MeasurementGating
Return the MEASUrement:GATing command.
Description
- This command sets or queries the global gating type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:GATing?query. - Using the
.verify(value)method will send theMEASUrement:GATing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing valuecommand.
SCPI Syntax
- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing?
Info
NONEturns off measurement gating.SCREenturns on gating, using the left and right edges of the screen.CURSorlimits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.LOGicspecifies that measurements are taken only on the portion of the waveform where the logic source is in the active state.SEARCHspecifies that measurements are taken based on search criteria.TIMelimits measurements to the portion of the waveform between the Start and End gate times.
Sub-properties
.active: TheMEASUrement:GATing:ACTivecommand..endtime: TheMEASUrement:GATing:ENDtimecommand..hysteresis: TheMEASUrement:GATing:HYSTeresiscommand..logicsource: TheMEASUrement:GATing:LOGICSourcecommand..midref: TheMEASUrement:GATing:MIDRefcommand..searchsource: TheMEASUrement:GATing:SEARCHSourcecommand..starttime: TheMEASUrement:GATing:STARTtimecommand.
property
¶
highlevel: MeasurementHighlevel
Return the MEASUrement:HIGHLEVel command tree.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.configuration: TheMEASUrement:HIGHLEVel:CONFIGurationcommand..edgequalifier: TheMEASUrement:HIGHLEVel:EDGEQUALifiercommand..inlowpass: TheMEASUrement:HIGHLEVel:INLOWPasscommand tree..l2ltol2n: TheMEASUrement:HIGHLEVel:L2LTOL2Ncommand..lineselected: TheMEASUrement:HIGHLEVel:LINESelectedcommand..outedgequalifier: TheMEASUrement:HIGHLEVel:OUTEDGEQUALifiercommand..outl2ltol2n: TheMEASUrement:HIGHLEVel:OUTL2LTOL2Ncommand..outlineselected: TheMEASUrement:HIGHLEVel:OUTLINESelectedcommand..outlowpass: TheMEASUrement:HIGHLEVel:OUTLOWPasscommand tree..outsource: TheMEASUrement:HIGHLEVel:OUTSOURCEcommand..outwiring: TheMEASUrement:HIGHLEVel:OUTWIRingcommand..source: TheMEASUrement:HIGHLEVel:SOURCEcommand..wiring: TheMEASUrement:HIGHLEVel:WIRingcommand.
property
¶
interp: MeasurementInterp
Return the MEASUrement:INTERp command.
Description
- This command sets or queries the interpolation mode used to locate edge crossings.
Usage
- Using the
.query()method will send theMEASUrement:INTERp?query. - Using the
.verify(value)method will send theMEASUrement:INTERp?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:INTERp valuecommand.
SCPI Syntax
- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?
Info
AUTOautomatically selects the interpolation mode.SINXspecifies sin(x)/x interpolation, where acquired points are fit to a curve.LINearspecifies linear interpolation, where acquired points are connected with straight lines.
property
¶
jittermodel: MeasurementJittermodel
Return the MEASUrement:JITTermodel command.
Description
- This command sets or queries the model used to separate random from deterministic jitter for jitter measurements.
Usage
- Using the
.query()method will send theMEASUrement:JITTermodel?query. - Using the
.verify(value)method will send theMEASUrement:JITTermodel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:JITTermodel valuecommand.
SCPI Syntax
- MEASUrement:JITTermodel {SPECTRAL|SPECTRALBUJ}
- MEASUrement:JITTermodel?
Info
SPECTRALsets the jitter separation model to spectral only.SPECTRALBUJsets the jitter separation model to spectral plus BUJ.
property
¶
list: MeasurementList
Return the MEASUrement:LIST command.
Description
- This query returns a comma separated list of all currently defined measurements.
Usage
- Using the
.query()method will send theMEASUrement:LIST?query. - Using the
.verify(value)method will send theMEASUrement:LIST?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:LIST?
property
¶
lockrj: MeasurementLockrj
Return the MEASUrement:LOCKRJ command.
Description
- This command sets or queries the state of RJ locking.
Usage
- Using the
.query()method will send theMEASUrement:LOCKRJ?query. - Using the
.verify(value)method will send theMEASUrement:LOCKRJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:LOCKRJ valuecommand.
SCPI Syntax
- MEASUrement:LOCKRJ {ON|OFF|<NR1>}
- MEASUrement:LOCKRJ?
Info
MEAS<x>specifies the measurement number.ONindicates that RJ locking is active.OFFindicates that RJ locking is off.<NR1>a 0 turns off RJ locking; any other value activates RJ locking.
property
¶
lockrjvalue: MeasurementLockrjvalue
Return the MEASUrement:LOCKRJValue command.
Description
- This command sets or queries the RJ lock value.
Usage
- Using the
.query()method will send theMEASUrement:LOCKRJValue?query. - Using the
.verify(value)method will send theMEASUrement:LOCKRJValue?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:LOCKRJValue valuecommand.
SCPI Syntax
- MEASUrement:LOCKRJValue <NR3>
- MEASUrement:LOCKRJValue?
Info
MEAS<x>specifies the measurement number.<NR3>default value = 1e-12; minimum value = 1e-15; maximum value = 1.
property
¶
math: dict[int, MeasurementMathItem]
Return the MEASUrement:MATH<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Sub-properties
.reflevels: TheMEASUrement:MATH<x>:REFLevelscommand tree.
property
¶
meas: dict[int, MeasurementMeasItem]
Return the MEASUrement:MEAS<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.ber: TheMEASUrement:MEAS<x>:BERcommand..bin: TheMEASUrement:MEAS<x>:BINcommand..bitcfgmode: TheMEASUrement:MEAS<x>:BITCfgmodecommand..bitend: TheMEASUrement:MEAS<x>:BITEndcommand..bitpcnt: TheMEASUrement:MEAS<x>:BITPcntcommand..bitstart: TheMEASUrement:MEAS<x>:BITSTartcommand..bittype: TheMEASUrement:MEAS<x>:BITTypecommand..burstedgtype: TheMEASUrement:MEAS<x>:BURSTEDGTYPecommand..ccresults: TheMEASUrement:MEAS<x>:CCRESUltscommand tree..clockrecovery: TheMEASUrement:MEAS<x>:CLOCKRecoverycommand tree..commonmode: TheMEASUrement:MEAS<x>:COMMONModecommand tree..cover: TheMEASUrement:MEAS<x>:COVercommand..customlimitsfile: TheMEASUrement:MEAS<x>:CUSTOMLIMITSFilecommand..cyclemode: TheMEASUrement:MEAS<x>:CYCLemodecommand..delay: TheMEASUrement:MEAS<x>:DELaycommand tree..displaystat: TheMEASUrement:MEAS<x>:DISPlaystatcommand tree..edge: TheMEASUrement:MEAS<x>:EDGE<x>command..edgeincre: TheMEASUrement:MEAS<x>:EDGEIncrecommand..edgequalone: TheMEASUrement:MEAS<x>:EDGEQUALONEcommand..edgequaltwo: TheMEASUrement:MEAS<x>:EDGEQUALTWOcommand..edgequalifier: TheMEASUrement:MEAS<x>:EDGEQUALifiercommand..edges: TheMEASUrement:MEAS<x>:EDGEScommand tree..eequal: TheMEASUrement:MEAS<x>:EEQUalcommand..failcount: TheMEASUrement:MEAS<x>:FAILCountcommand..filterrangefrom: TheMEASUrement:MEAS<x>:FILTERRANGEFROMcommand..filterrangeto: TheMEASUrement:MEAS<x>:FILTERRANGETOcommand..filters: TheMEASUrement:MEAS<x>:FILTerscommand tree..freq: TheMEASUrement:MEAS<x>:FREQcommand..fromedgesearchdirect: TheMEASUrement:MEAS<x>:FROMEDGESEARCHDIRectcommand..fromsymbol: TheMEASUrement:MEAS<x>:FROMSymbolcommand tree..fromedge: TheMEASUrement:MEAS<x>:FROMedgecommand..fundcurrent: TheMEASUrement:MEAS<x>:FUNDCURRentcommand..gating: TheMEASUrement:MEAS<x>:GATingcommand..globalref: TheMEASUrement:MEAS<x>:GLOBalrefcommand..harmonicsclass: TheMEASUrement:MEAS<x>:HARMONICSCLasscommand..harmonicssource: TheMEASUrement:MEAS<x>:HARMONICSSOURcecommand..harmonicsstd: TheMEASUrement:MEAS<x>:HARMONICSStdcommand..harmonicsunits: TheMEASUrement:MEAS<x>:HARMONICSUNitscommand..highlevel: TheMEASUrement:MEAS<x>:HIGHLEVelcommand tree..highrefvoltage: TheMEASUrement:MEAS<x>:HIGHREFVoltagecommand..hlevel: TheMEASUrement:MEAS<x>:HLEVelcommand tree..htorque: TheMEASUrement:MEAS<x>:HTORquecommand..hvoltage: TheMEASUrement:MEAS<x>:HVOLtagecommand..idletime: TheMEASUrement:MEAS<x>:IDLETimecommand..inputlevel: TheMEASUrement:MEAS<x>:INPUTLEVelcommand..inputpower: TheMEASUrement:MEAS<x>:INPUTPOwercommand..jittersummary: TheMEASUrement:MEAS<x>:JITTERSummarycommand tree..label: TheMEASUrement:MEAS<x>:LABelcommand..lineselected: TheMEASUrement:MEAS<x>:LINESelectedcommand..lowrefvoltage: TheMEASUrement:MEAS<x>:LOWREFVoltagecommand..ltorque: TheMEASUrement:MEAS<x>:LTORquecommand..ltype: TheMEASUrement:MEAS<x>:LTYPecommand..lunits: TheMEASUrement:MEAS<x>:LUNITscommand..lvoltage: TheMEASUrement:MEAS<x>:LVOLtagecommand..maxcurrent: TheMEASUrement:MEAS<x>:MAXCUrrentcommand..maxcycle: TheMEASUrement:MEAS<x>:MAXCyclecommand..maxgvoltage: TheMEASUrement:MEAS<x>:MAXGVoltagecommand..maxvoltage: TheMEASUrement:MEAS<x>:MAXVoltagecommand..measrange: TheMEASUrement:MEAS<x>:MEASRangecommand tree..mech: TheMEASUrement:MEAS<x>:MECHcommand tree..mincycle: TheMEASUrement:MEAS<x>:MINCyclecommand..oddeven: TheMEASUrement:MEAS<x>:ODDEVencommand..ofilters: TheMEASUrement:MEAS<x>:OFILterscommand tree..osangle: TheMEASUrement:MEAS<x>:OSANglecommand..outedgequalifier: TheMEASUrement:MEAS<x>:OUTEDGEQUALifiercommand..outfilters: TheMEASUrement:MEAS<x>:OUTFILTerscommand tree..outputvoltage: TheMEASUrement:MEAS<x>:OUTPUT<n>VOLTagecommand..passfailenabled: TheMEASUrement:MEAS<x>:PASSFAILENabledcommand..passfailhighlimit: TheMEASUrement:MEAS<x>:PASSFAILHIGHlimitcommand..passfaillimit: TheMEASUrement:MEAS<x>:PASSFAILLIMitcommand..passfaillowlimit: TheMEASUrement:MEAS<x>:PASSFAILLOWlimitcommand..passfailmargin: TheMEASUrement:MEAS<x>:PASSFAILMARgincommand..passfailwhen: TheMEASUrement:MEAS<x>:PASSFAILWHENcommand..patterndetection: TheMEASUrement:MEAS<x>:PATTERNDETECTIONcommand..patternlength: TheMEASUrement:MEAS<x>:PATTERNLENgthcommand..patterntype: TheMEASUrement:MEAS<x>:PATTERNTYPecommand..pcount: TheMEASUrement:MEAS<x>:PCOUNtcommand..perfreq: TheMEASUrement:MEAS<x>:PERFREQcommand tree..polarity: TheMEASUrement:MEAS<x>:POLaritycommand..population: TheMEASUrement:MEAS<x>:POPUlationcommand tree..powerfactor: TheMEASUrement:MEAS<x>:POWERFACtorcommand..pregion: TheMEASUrement:MEAS<x>:PREGioncommand..pwidth: TheMEASUrement:MEAS<x>:PWIDthcommand..redge: TheMEASUrement:MEAS<x>:REDGecommand..reflevels: TheMEASUrement:MEAS<x>:REFLevelscommand tree..reflevels1: TheMEASUrement:MEAS<x>:REFLevels1command tree..refmode: TheMEASUrement:MEAS<x>:REFModecommand..refvoltageval: TheMEASUrement:MEAS<x>:REFVOLTAGE<n>Valcommand..refvoltage: TheMEASUrement:MEAS<x>:REFVoltagecommand..results: TheMEASUrement:MEAS<x>:RESUltscommand tree..ripplefreqval: TheMEASUrement:MEAS<x>:RIPPLEFREQ<n>Valcommand..sequence: TheMEASUrement:MEAS<x>:SEQuencecommand..signalfrequency: TheMEASUrement:MEAS<x>:SIGNALFREQUEncycommand..signaltype: TheMEASUrement:MEAS<x>:SIGNALTypecommand..slabs: TheMEASUrement:MEAS<x>:SLABscommand..slpct: TheMEASUrement:MEAS<x>:SLPCtcommand..sltype: TheMEASUrement:MEAS<x>:SLTYpecommand..smoothingfilter: TheMEASUrement:MEAS<x>:SMOOTHINGFILTERcommand..source: TheMEASUrement:MEAS<x>:SOURCEcommand..source1: TheMEASUrement:MEAS<x>:SOUrce1command..ssc: TheMEASUrement:MEAS<x>:SSCcommand tree..status: TheMEASUrement:MEAS<x>:STATUScommand..stlabs: TheMEASUrement:MEAS<x>:STLABscommand..stlpct: TheMEASUrement:MEAS<x>:STLPctcommand..stype: TheMEASUrement:MEAS<x>:STYPecommand..sunits: TheMEASUrement:MEAS<x>:SUNitscommand..tckavg: TheMEASUrement:MEAS<x>:TCKAVGcommand..tconstant: TheMEASUrement:MEAS<x>:TCONstantcommand..timingmode: TheMEASUrement:MEAS<x>:TIMINGModecommand..tmethod: TheMEASUrement:MEAS<x>:TMEThodcommand..toedgesearchdirect: TheMEASUrement:MEAS<x>:TOEDGESEARCHDIRectcommand..toedge: TheMEASUrement:MEAS<x>:TOEdgecommand..tosymbol: TheMEASUrement:MEAS<x>:TOSYmbolcommand tree..transition: TheMEASUrement:MEAS<x>:TRANSitioncommand..type: TheMEASUrement:MEAS<x>:TYPecommand..waittime: TheMEASUrement:MEAS<x>:WAITTimecommand..windowlength: TheMEASUrement:MEAS<x>:WINDOWLENgthcommand..xunit: TheMEASUrement:MEAS<x>:XUNITcommand..yunit: TheMEASUrement:MEAS<x>:YUNITcommand..stltype: TheMEASUrement:MEAS<x>:STLTYpecommand.
property
¶
measrange: MeasurementMeasrange
Return the MEASUrement:MEASRange command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.max: TheMEASUrement:MEASRange:MAXcommand..min: TheMEASUrement:MEASRange:MINcommand..state: TheMEASUrement:MEASRange:STATEcommand.
property
¶
mech: MeasurementMech
Return the MEASUrement:MECH command tree.
Usage
- Using the
.query()method will send theMEASUrement:MECH?query. - Using the
.verify(value)method will send theMEASUrement:MECH?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.eindexz: TheMEASUrement:MECH:EINDexzcommand..gratio: TheMEASUrement:MECH:GRATiocommand..munits: TheMEASUrement:MECH:MUNitscommand..ppairs: TheMEASUrement:MECH:PPAirscommand..pprotation: TheMEASUrement:MECH:PPRotationcommand..source1: TheMEASUrement:MECH:SOUrce1command..stype: TheMEASUrement:MECH:STYPecommand.
property
¶
minui: MeasurementMinui
Return the MEASUrement:MINUI command.
Description
- This command sets or queries the minimum number of unit intervals required for BUJ analysis.
Usage
- Using the
.query()method will send theMEASUrement:MINUI?query. - Using the
.verify(value)method will send theMEASUrement:MINUI?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MINUI valuecommand.
SCPI Syntax
- MEASUrement:MINUI <NR3>
- MEASUrement:MINUI?
Info
<NR3>is the minimum number of unit intervals required for BUJ analysis.
property
¶
population: MeasurementPopulation
Return the MEASUrement:POPUlation command tree.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.limit: TheMEASUrement:POPUlation:LIMITcommand tree.
property
¶
ref: dict[int, MeasurementRefItem]
Return the MEASUrement:REF<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.reflevels: TheMEASUrement:REF<x>:REFLevelscommand tree.
property
¶
reflevels: MeasurementReflevels
Return the MEASUrement:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.absolute: TheMEASUrement:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:REFLevels:BASETopcommand..jittermode: TheMEASUrement:REFLevels:JITTERMODEcommand..method: TheMEASUrement:REFLevels:METHodcommand..mode: TheMEASUrement:REFLevels:MODEcommand..percent: TheMEASUrement:REFLevels:PERCentcommand tree..type: TheMEASUrement:REFLevels:TYPEcommand.
property
¶
results: MeasurementResults
Return the MEASUrement:RESUlts command tree.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.history: TheMEASUrement:RESUlts:HISTorycommand tree.
property
¶
statistics: MeasurementStatistics
Return the MEASUrement:STATIstics command tree.
Usage
- Using the
.query()method will send theMEASUrement:STATIstics?query. - Using the
.verify(value)method will send theMEASUrement:STATIstics?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.cyclemode: TheMEASUrement:STATIstics:CYCLEModecommand.
property
¶
wbg: MeasurementWbg
Return the MEASUrement:WBG command tree.
Usage
- Using the
.query()method will send theMEASUrement:WBG?query. - Using the
.verify(value)method will send theMEASUrement:WBG?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.pdevice: TheMEASUrement:WBG:PDEVicecommand.
Bases: SCPICmdWrite
The MEASUrement:ADDMEAS command.
Description
- This command adds a measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:ADDMEAS valuecommand.
SCPI Syntax
- MEASUrement:ADDMEAS {ACCOMMONMODE|ACRMS|AMPlITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|CCJITTER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HEIGHT|HEIGHTBER|HIGH|HIGHTIME|HOLD|IMDAPOWERQUALITY|IMDAHARMONICS|IMDAINPUTVOLTAGE|IMDAINPUTCURRENT|IMDAINPUTPOWER|IMDAPHASORDIAGRAM|IMDAEFFICIENCY|IMDALINERIPPLE|IMDASWITCHRIPPLE|IMDADQ0|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NPJ|NWIDTTH|PDUTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SETUP|SKEW|SRJ|SSCFREQDEV|SSCMODRATE|TIE|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WIDTH|WIDTHBER}
Info
ACCOMMONMODEAC Common Mode (Pk-Pk) is the peak-to-peak of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.ACRMS(AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.AMPLITUDEis the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.Amplitude = High - LowAREAis the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.BASEis the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.BITAMPLITUDE(Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITHIGH(Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITLOW(Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BURSTWIDTH(Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.COMMONMODE(DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.CCJITTER(Cycle-to-Cycle jitter) measures how much the clock period changes between any two adjacent cycles. Cycle-to-Cycle jitter is measured by applying a first order difference operation to the period jitter.DATARATE(Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.DCD(duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDJ(data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDRAOS(area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.DDRAOSPERTCK(area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAOSPERUI(area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRAUS(area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.DDRAUSPERTCK(area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAUSPERUI(area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRHOLDDIFF(hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.DDRSETUPDIFF(setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.DDRTCHABS(absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.DDRTCHAVERAGE(average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles. This measurement is made across the entire record.DDRTCKAVERAGE(average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles. This measurement is made across the entire record.DDRTCLABS(absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.DDRTCLAVERAGE(average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.DDRTERRMN(cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).DDRTERRN(cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).DDRTJITCC(cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.DDRTJITDUTY(half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.DDRTJITPER(clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.DDRTPST(read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.DDRTRPRE(read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRTWPREis the width of the Write burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRVIXACis the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.DDRTDQSCKis the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.DELayis the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.DJ(deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DJDIRAC(dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.EYEHIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.EYELOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.FALLSLEWRATE(Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.FALLTIME(Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.FREQuencyis the reciprocal of Period. This measurement is made on each cycle in the record.F2is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F4is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F8is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.HEIGHT(Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HEIGHTBER(Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGHTIME(High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.HOLD(Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.IMDAPOWERQUALITYmeasures the operating Frequency, RMS values of the voltage and current, Crest Factors of the voltage and current, Real Power, Reactive Power, Apparent Power, Power Factor, and Phase Angle of the AC signal. Plots the Phasor diagram. This measurement requires the IMDA option.IMDAHARMONICSmeasures the signal amplitudes at the fundamental line frequency and its harmonics. Measures the RMS amplitude and Total Harmonic Distortion of the signal. Plots the Harmonics Bar Graph. This measurement requires the IMDA option.IMDAINPUTVOLTAGEmeasures the RMS value of the input voltage for all phases based on the configured wiring. This measurement requires the IMDA option.IMDAINPUTCURRENTmeasures the RMS value of the input current for all phases based on the configured wiring. This measurement requires the IMDA option.IMDAINPUTPOWERmeasures the RMS and peak-to-peak values of the AC signal. This measurement requires the IMDA option.IMDAPHASORDIAGRAMplots Vrms and Irms and phase angles between voltage(s) and current(s) per winding pair. This measurement requires the IMDA option.IMDAEFFICIENCYmeasures the ratio of output power to input power per phase for a AC input and Drive output. Measures the total efficiency of the system. This measurement requires the IMDA option.IMDALINERIPPLEmeasures the RMS value of the input power for all phases based on the configured wiring. Measures the True / Apparent / Reactive Power for all the phases. This measurement requires the IMDA option.IMDASWITCHRIPPLEJITTERSUMMARYmeasures the RMS and peak-to-peak values of the switching signal. This measurement requires the IMDA option.IMDADQ0measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0.JITTERSUMMARY(Jitter Summary) is a group consisting of the following measurements: TIE, TJ@BER, Eye Width@BER, Eye Height@BER, RJ-δδ, DJ-δδ, PJ, DDJ, DcD, F/2, F/4, F/8. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J2is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J9is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.LOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.LOWTIME(Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.MAXimumis the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.MEANis the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.MINImumis the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.NDUty(Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.Negative Duty Cycle = (Negative Width) / Period × 100%NPERIOD(Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.NPJ(non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.NOVershoot(Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Negative Overshoot = (Base - Minimum) / Amplitude × 100%)NWIdth(Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.PDUTY(Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.Positive Duty Cycle = (Positive Width)/Period × 100%PERIODis the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.PHASEis the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.PHASENOISE(Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.PJ(periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.PK2Pk(Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.POVERSHOOT(Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Positive Overshoot = (Maximum - Top) / Amplitude ×100%PWIDTH(Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.QFACTOR(Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RISESLEWRATE(Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RISETIMERise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RJ(random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RJDIRAC(dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RMSis the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.SRJ(sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCFREQDEV(SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCMODRATE(SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SETUP(Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.SKEWSkew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.TIE(time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.TIMEOUTSIDELEVELTime Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.TIMETOMAXTime to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.TIMETOMINTime to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.TJBER(total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TNTRATIOT/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TOPis the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.UNITINTERVAL(Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.VDIFFXOVR(Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTH(Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTHBER(Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
Bases: SCPICmdWrite
The MEASUrement:ADDNew command.
Description
- This command adds the specified measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:ADDNew valuecommand.
SCPI Syntax
- MEASUrement:ADDNew 'QString'
Info
'QString'is the measurement to add. The argument is of the form ‘MEAS’ where NR1 ≥ 1.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:ANNOTate command.
Description
- This command sets or queries the annotation state for measurements.
Usage
- Using the
.query()method will send theMEASUrement:ANNOTate?query. - Using the
.verify(value)method will send theMEASUrement:ANNOTate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:ANNOTate valuecommand.
SCPI Syntax
- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?
Info
OFFturns off measurement annotations.AUTOturns on visible measurement annotations.
Bases: SCPICmdWrite
The MEASUrement:AUTOset command.
Description
- This command performs an analysis jitter autoset.
Usage
- Using the
.write(value)method will send theMEASUrement:AUTOset valuecommand.
SCPI Syntax
- MEASUrement:AUTOset {EXECute|THREEPHASEAUTOset|WBGPREset|DPMAutoset|DPMPReset}
Info
EXECuteperforms an analysis jitter autoset.THREEPHASEAUTOsetperforms an IMDA 3 phase autoset.WBGPREsetperforms a measurement specific preset. Requires a WBG-DPT license.DPMAutosetperforms a power rail autoset. Requires option 5-DPM (5 Series MSO instruments) or 6-DPM (6 Series MSO instrument).DPMPResetperforms a power rail preset. Requires option 5-DPM (5 Series MSO instruments) or 6-DPM (6 Series MSO instrument).
Bases: ValidatedChannel, SCPICmdRead
The MEASUrement:CH<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.reflevels: TheMEASUrement:CH<x>:REFLevelscommand tree.
property
¶
reflevels: MeasurementChannelReflevels
Return the MEASUrement:CH<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.absolute: TheMEASUrement:CH<x>:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:CH<x>:REFLevels:BASETopcommand..method: TheMEASUrement:CH<x>:REFLevels:METHodcommand..percent: TheMEASUrement:CH<x>:REFLevels:PERCentcommand tree.
Bases: SCPICmdRead
The MEASUrement:CH<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.absolute: TheMEASUrement:CH<x>:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:CH<x>:REFLevels:BASETopcommand..method: TheMEASUrement:CH<x>:REFLevels:METHodcommand..percent: TheMEASUrement:CH<x>:REFLevels:PERCentcommand tree.
property
¶
absolute: MeasurementChannelReflevelsAbsolute
Return the MEASUrement:CH<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.fallhigh: TheMEASUrement:CH<x>:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:CH<x>:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:CH<x>:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:CH<x>:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:CH<x>:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:CH<x>:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:CH<x>:REFLevels:ABSolute:TYPEcommand.
property
¶
basetop: MeasurementChannelReflevelsBasetop
Return the MEASUrement:CH<x>:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:BASETop valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?
Info
AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
property
¶
Return the MEASUrement:CH<x>:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?
Info
PERCentspecifies percent reference level units.ABSolutespecifies absolute reference level units.
property
¶
percent: MeasurementChannelReflevelsPercent
Return the MEASUrement:CH<x>:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.fallhigh: TheMEASUrement:CH<x>:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:CH<x>:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:CH<x>:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:CH<x>:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:CH<x>:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:CH<x>:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:CH<x>:REFLevels:PERCent:TYPEcommand.
Bases: SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.fallhigh: TheMEASUrement:CH<x>:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:CH<x>:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:CH<x>:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:CH<x>:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:CH<x>:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:CH<x>:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:CH<x>:REFLevels:ABSolute:TYPEcommand.
property
¶
Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?
Info
<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
property
¶
Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?
Info
<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
property
¶
Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?
Info
<NR3>is the mid reference level used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.
property
¶
hysteresis: MeasurementChannelReflevelsAbsoluteHysteresis
Return the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?
Info
<NR3>is the hysteresis value used for autoset.
property
¶
Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?
Info
<NR3>is the high reference level of the rising edge when the source ref level method is set to absolute.
property
¶
Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?
Info
<NR3>is the low reference level of the rising edge when the source ref level method is set to absolute.
property
¶
Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?
Info
<NR3>is the mid reference level of the rising edge when the source ref level method is set to absolute.
property
¶
Return the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the source. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?
Info
SAMEspecifies that the absolute reference levels for the specified measurement channel are the same.UNIQuespecifies that the absolute reference levels for the specified measurement channel are not the same.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?
Info
<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?
Info
<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?
Info
<NR3>is the mid reference level used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?
Info
<NR3>is the hysteresis value used for autoset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?
Info
<NR3>is the high reference level of the rising edge when the source ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?
Info
<NR3>is the low reference level of the rising edge when the source ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?
Info
<NR3>is the mid reference level of the rising edge when the source ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the source. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?
Info
SAMEspecifies that the absolute reference levels for the specified measurement channel are the same.UNIQuespecifies that the absolute reference levels for the specified measurement channel are not the same.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:BASETop valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?
Info
AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?
Info
PERCentspecifies percent reference level units.ABSolutespecifies absolute reference level units.
Bases: SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.fallhigh: TheMEASUrement:CH<x>:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:CH<x>:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:CH<x>:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:CH<x>:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:CH<x>:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:CH<x>:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:CH<x>:REFLevels:PERCent:TYPEcommand.
property
¶
Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the low reference level when the measurement Ref level method is set to Percent.
property
¶
Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?
Info
<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
property
¶
hysteresis: MeasurementChannelReflevelsPercentHysteresis
Return the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?
Info
<NR3>is the hysteresis value used for the autoset.
property
¶
Return the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?
Info
<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.
Description
- This command specifies or queries the reference level percent type for the measurement. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?
Info
TENNinetyspecifies reference levels at the 10 and 90% levels.TWENtyeightyspecifies reference levels at the 20 and 80% levels.CUSTomspecifies custom reference levels.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the low reference level when the measurement Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?
Info
<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?
Info
<NR3>is the hysteresis value used for the autoset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?
Info
<NR3>is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?
Info
<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.
Description
- This command specifies or queries the reference level percent type for the measurement. The channel number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:CH<x>:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CH<x>:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?
Info
TENNinetyspecifies reference levels at the 10 and 90% levels.TWENtyeightyspecifies reference levels at the 20 and 80% levels.CUSTomspecifies custom reference levels.
Bases: SCPICmdRead
The MEASUrement:CLOCKRecovery command tree.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.advanced: TheMEASUrement:CLOCKRecovery:ADVancedcommand tree..clockfrequency: TheMEASUrement:CLOCKRecovery:CLOCKFrequencycommand..clockmultiplier: TheMEASUrement:CLOCKRecovery:CLOCKMultipliercommand..constclockmode: TheMEASUrement:CLOCKRecovery:CONSTCLOCKMODecommand..damping: TheMEASUrement:CLOCKRecovery:DAMPingcommand..datapath: TheMEASUrement:CLOCKRecovery:DATAPathcommand..datarate: TheMEASUrement:CLOCKRecovery:DATARatecommand..explicitclockmode: TheMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODecommand..jtfbandwidth: TheMEASUrement:CLOCKRecovery:JTFBandwidthcommand..loopbandwidth: TheMEASUrement:CLOCKRecovery:LOOPBandwidthcommand..meanautocalculate: TheMEASUrement:CLOCKRecovery:MEANAUTOCalculatecommand..method: TheMEASUrement:CLOCKRecovery:METHodcommand..model: TheMEASUrement:CLOCKRecovery:MODelcommand..nominaloffset: TheMEASUrement:CLOCKRecovery:NOMINALOFFsetcommand..standard: TheMEASUrement:CLOCKRecovery:STAndardcommand.
property
¶
advanced: MeasurementClockrecoveryAdvanced
Return the MEASUrement:CLOCKRecovery:ADVanced command tree.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:ADVanced?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:ADVanced?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.method: TheMEASUrement:CLOCKRecovery:ADVanced:METHodcommand.
property
¶
clockfrequency: MeasurementClockrecoveryClockfrequency
Return the MEASUrement:CLOCKRecovery:CLOCKFrequency command.
Description
- This command sets or queries the global clock frequency used when fixed constant clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:CLOCKFrequency?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:CLOCKFrequency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:CLOCKFrequency valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:CLOCKRecovery:CLOCKFrequency?
Info
<NR3>is the global clock frequency used with Constant Clock - Fixed clock recovery method.
property
¶
clockmultiplier: MeasurementClockrecoveryClockmultiplier
Return the MEASUrement:CLOCKRecovery:CLOCKMultiplier command.
Description
- This command sets or queries the global clock multiplier used when explicit clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:CLOCKMultiplier?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:CLOCKMultiplier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:CLOCKMultiplier valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:CLOCKRecovery:CLOCKMultiplier?
Info
<NR3>is the global clock multiplier.
property
¶
constclockmode: MeasurementClockrecoveryConstclockmode
Return the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe command.
Description
- This command sets or queries the global constant clock mode used when constant clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:CONSTCLOCKMODe?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:CONSTCLOCKMODe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:CONSTCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe?
Info
MEANsets the constant clock mode to MEAN.MEDiansets the constant clock mode to MEDian.FIXedsets the constant clock mode to FIXed.
property
¶
damping: MeasurementClockrecoveryDamping
Return the MEASUrement:CLOCKRecovery:DAMPing command.
Description
- This command sets or queries the global damping value used when PLL clock recovery is
used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:DAMPing?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:DAMPing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:DAMPing valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:CLOCKRecovery:DAMPing?
Info
<NR3>is the global clock recovery damping value.
property
¶
datapath: MeasurementClockrecoveryDatapath
Return the MEASUrement:CLOCKRecovery:DATAPath command.
Description
- This command sets or queries the global file containing the data pattern used when
known data pattern clock recovery is used for the measurement. This will affect
measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:DATAPath?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:DATAPath?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:DATAPath valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:DATAPath <QString>
- MEASUrement:CLOCKRecovery:DATAPath?
Info
<QString>is the path and filename, in quotes, of the file containing the data pattern.
property
¶
datarate: MeasurementClockrecoveryDatarate
Return the MEASUrement:CLOCKRecovery:DATARate command.
Description
- This command sets or queries the global nominal data bit rate used when nominal data
rate clock recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:DATARate?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:DATARate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:DATARate valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:DATARate <NR3>
- MEASUrement:CLOCKRecovery:DATARate?
Info
<NR3>is the global value for the Nominal data rate.
property
¶
explicitclockmode: MeasurementClockrecoveryExplicitclockmode
Return the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe command.
Description
- This command sets or queries the global explicit clock mode used when explicit clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?
Info
EDGEsets the clock mode to clock edge.PLLsets the clock mode to phase locked loop.
property
¶
jtfbandwidth: MeasurementClockrecoveryJtfbandwidth
Return the MEASUrement:CLOCKRecovery:JTFBandwidth command.
Description
- This command sets or queries the global JTF bandwidth used when PLL clock recovery is
used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:JTFBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:JTFBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:JTFBandwidth valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:CLOCKRecovery:JTFBandwidth?
Info
<NR3>is the global clock recovery JTF bandwidth.
property
¶
loopbandwidth: MeasurementClockrecoveryLoopbandwidth
Return the MEASUrement:CLOCKRecovery:LOOPBandwidth command.
Description
- This command sets or queries the global loop bandwidth used when PLL clock recovery is
used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:LOOPBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:LOOPBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:LOOPBandwidth valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:CLOCKRecovery:LOOPBandwidth?
Info
<NR3>is the global loop bandwidth.
property
¶
meanautocalculate: MeasurementClockrecoveryMeanautocalculate
Return the MEASUrement:CLOCKRecovery:MEANAUTOCalculate command.
Description
- This command sets or queries how often the clock is calculated when constant clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:MEANAUTOCalculate?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:MEANAUTOCalculate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:MEANAUTOCalculate valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate?
Info
FIRSTcalculates the clock on the first acquisition.EVERYcalculates the clock on every acquisition.
property
¶
method: MeasurementClockrecoveryMethod
Return the MEASUrement:CLOCKRecovery:METHod command.
Description
- This command sets or queries the global clock recovery method for the measurement.
This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:METHod?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:METHod valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:CLOCKRecovery:METHod?
Info
PLLspecifies using the phase locked loop.CONSTANTCLOCKspecifies using a constant clock.EXPLICITCLOCKspecifies using an explicit clock.
property
¶
Return the MEASUrement:CLOCKRecovery:MODel command.
Description
- This command sets or queries the global phase locked loop (PLL) clock recovery model
used when PLL clock recovery is used for the measurement. This will affect
measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:MODel?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:MODel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:MODel valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:MODel {TYPE<x>}
- MEASUrement:CLOCKRecovery:MODel?
Info
TYPE1PLL clock recovery uses PLL model type I.TYPE2PLL clock recovery uses PLL model type II.
property
¶
nominaloffset: MeasurementClockrecoveryNominaloffset
Return the MEASUrement:CLOCKRecovery:NOMINALOFFset command.
Description
- This command sets or queries the global offset value used when explicit clock recovery
is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:CLOCKRecovery:NOMINALOFFset?
Info
<NR3>is the global clock offset.
Sub-properties
.selectiontype: TheMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtypecommand.
property
¶
standard: MeasurementClockrecoveryStandard
Return the MEASUrement:CLOCKRecovery:STAndard command.
Description
- This command sets or queries the global communications standard used when PLL clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:STAndard?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:STAndard?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:STAndard valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:CLOCKRecovery:STAndard?
Info
CUSTomsets a custom standard.ENET100sets the standard to ENET100.FW1394BS400Bsets the standard to FW1394BS400B.FW1394BS800Bsets the standard to FW1394BS800B.FW1394BS1600Bsets the standard to FW1394BS1600B.FBD1sets the standard to FBD1.FBD2sets the standard to FBD2.FBD3sets the standard to FBD3.FC133sets the standard to FC133.FC266sets the standard to FC266.FC531sets the standard to FC531.FC1063sets the standard to FC1063.FC2125sets the standard to FC2125.FC4250sets the standard to FC4250.FC8500sets the standard to FC8500.ENET1000sets the standard to ENET1000.IBA2500sets the standard to IBA2500.IBA_GEN2sets the standard toIBA_GEN2.OC1sets the standard to OC1.OC3sets the standard to OC3.OC12sets the standard to OC12.OC48sets the standard to OC48.PCIE_GEN1sets the standard toPCIE_GEN1.PCIE_GEN2sets the standard toPCIE_GEN2.PCIE_GEN3sets the standard toPCIE_GEN3.RIO125sets the standard to RIO125.RIO250sets the standard to RIO250.RIO3125sets the standard to RIO3125.SAS15_NOSSCsets the standard toSAS15_NOSSC.SAS3_NOSSCsets the standard toSAS3_NOSSC.SAS6_NOSSCsets the standard toSAS6_NOSSC.SAS12_NOSSCsets the standard toSAS12_NOSSC.SAS15_SSCsets the standard toSAS15_SSC.SAS3_SSCsets the standard toSAS3_SSC.SAS6_SSCsets the standard toSAS6_SSC.SAS12_SSCsets the standard toSAS12_SSC.SATA_GEN1sets the standard toSATA_GEN1.SATA_GEN2sets the standard toSATA_GEN2.SATA_GEN3sets the standard toSATA_GEN3.USB3sets the standard to USB3.XAUIsets the standard to XAUI.XAUI_GEN2sets the standard toXAUI_GEN2.
Bases: SCPICmdRead
The MEASUrement:CLOCKRecovery:ADVanced command tree.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:ADVanced?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:ADVanced?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.method: TheMEASUrement:CLOCKRecovery:ADVanced:METHodcommand.
property
¶
Return the MEASUrement:CLOCKRecovery:ADVanced:METHod command.
Description
- This command sets or queries the global advanced clock recovery method. This will
affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:ADVanced:METHod?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:ADVanced:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:ADVanced:METHod valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:CLOCKRecovery:ADVanced:METHod?
Info
NONEsets to use no advanced CRD method.NOMinalsets the advanced CRD method to Nominal Data Rate.PATTernsets the advanced CDR method to use a Known Data Pattern.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:ADVanced:METHod command.
Description
- This command sets or queries the global advanced clock recovery method. This will affect
measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:ADVanced:METHod?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:ADVanced:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:ADVanced:METHod valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:CLOCKRecovery:ADVanced:METHod?
Info
NONEsets to use no advanced CRD method.NOMinalsets the advanced CRD method to Nominal Data Rate.PATTernsets the advanced CDR method to use a Known Data Pattern.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:CLOCKFrequency command.
Description
- This command sets or queries the global clock frequency used when fixed constant clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:CLOCKFrequency?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:CLOCKFrequency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:CLOCKFrequency valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:CLOCKRecovery:CLOCKFrequency?
Info
<NR3>is the global clock frequency used with Constant Clock - Fixed clock recovery method.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:CLOCKMultiplier command.
Description
- This command sets or queries the global clock multiplier used when explicit clock recovery
is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:CLOCKMultiplier?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:CLOCKMultiplier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:CLOCKMultiplier valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:CLOCKRecovery:CLOCKMultiplier?
Info
<NR3>is the global clock multiplier.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:CONSTCLOCKMODe command.
Description
- This command sets or queries the global constant clock mode used when constant clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:CONSTCLOCKMODe?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:CONSTCLOCKMODe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:CONSTCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe?
Info
MEANsets the constant clock mode to MEAN.MEDiansets the constant clock mode to MEDian.FIXedsets the constant clock mode to FIXed.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:DAMPing command.
Description
- This command sets or queries the global damping value used when PLL clock recovery is used
for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:DAMPing?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:DAMPing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:DAMPing valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:CLOCKRecovery:DAMPing?
Info
<NR3>is the global clock recovery damping value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:DATAPath command.
Description
- This command sets or queries the global file containing the data pattern used when known
data pattern clock recovery is used for the measurement. This will affect measurements
whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:DATAPath?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:DATAPath?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:DATAPath valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:DATAPath <QString>
- MEASUrement:CLOCKRecovery:DATAPath?
Info
<QString>is the path and filename, in quotes, of the file containing the data pattern.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:DATARate command.
Description
- This command sets or queries the global nominal data bit rate used when nominal data rate
clock recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:DATARate?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:DATARate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:DATARate valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:DATARate <NR3>
- MEASUrement:CLOCKRecovery:DATARate?
Info
<NR3>is the global value for the Nominal data rate.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe command.
Description
- This command sets or queries the global explicit clock mode used when explicit clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?
Info
EDGEsets the clock mode to clock edge.PLLsets the clock mode to phase locked loop.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:JTFBandwidth command.
Description
- This command sets or queries the global JTF bandwidth used when PLL clock recovery is used
for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:JTFBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:JTFBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:JTFBandwidth valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:CLOCKRecovery:JTFBandwidth?
Info
<NR3>is the global clock recovery JTF bandwidth.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:LOOPBandwidth command.
Description
- This command sets or queries the global loop bandwidth used when PLL clock recovery is
used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:LOOPBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:LOOPBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:LOOPBandwidth valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:CLOCKRecovery:LOOPBandwidth?
Info
<NR3>is the global loop bandwidth.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:MEANAUTOCalculate command.
Description
- This command sets or queries how often the clock is calculated when constant clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:MEANAUTOCalculate?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:MEANAUTOCalculate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:MEANAUTOCalculate valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate?
Info
FIRSTcalculates the clock on the first acquisition.EVERYcalculates the clock on every acquisition.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:METHod command.
Description
- This command sets or queries the global clock recovery method for the measurement. This
will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:METHod?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:METHod valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:CLOCKRecovery:METHod?
Info
PLLspecifies using the phase locked loop.CONSTANTCLOCKspecifies using a constant clock.EXPLICITCLOCKspecifies using an explicit clock.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:MODel command.
Description
- This command sets or queries the global phase locked loop (PLL) clock recovery model used
when PLL clock recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:MODel?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:MODel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:MODel valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:MODel {TYPE<x>}
- MEASUrement:CLOCKRecovery:MODel?
Info
TYPE1PLL clock recovery uses PLL model type I.TYPE2PLL clock recovery uses PLL model type II.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:NOMINALOFFset command.
Description
- This command sets or queries the global offset value used when explicit clock recovery is
used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:CLOCKRecovery:NOMINALOFFset?
Info
<NR3>is the global clock offset.
Properties
.selectiontype: TheMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtypecommand.
property
¶
selectiontype: MeasurementClockrecoveryNominaloffsetSelectiontype
Return the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.
Description
- This command sets or queries the global offset type used when explicit clock recovery
is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
Info
AUTOsets the selection type to AUTO.MANUALsets the selection type to MANUAL.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.
Description
- This command sets or queries the global offset type used when explicit clock recovery is
used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
Info
AUTOsets the selection type to AUTO.MANUALsets the selection type to MANUAL.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:CLOCKRecovery:STAndard command.
Description
- This command sets or queries the global communications standard used when PLL clock
recovery is used for the measurement. This will affect measurements whose
:MEASUrement:MEAS<x>:CLOCKRecovery:GLOBalflag is set to 1.
Usage
- Using the
.query()method will send theMEASUrement:CLOCKRecovery:STAndard?query. - Using the
.verify(value)method will send theMEASUrement:CLOCKRecovery:STAndard?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:CLOCKRecovery:STAndard valuecommand.
SCPI Syntax
- MEASUrement:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:CLOCKRecovery:STAndard?
Info
CUSTomsets a custom standard.ENET100sets the standard to ENET100.FW1394BS400Bsets the standard to FW1394BS400B.FW1394BS800Bsets the standard to FW1394BS800B.FW1394BS1600Bsets the standard to FW1394BS1600B.FBD1sets the standard to FBD1.FBD2sets the standard to FBD2.FBD3sets the standard to FBD3.FC133sets the standard to FC133.FC266sets the standard to FC266.FC531sets the standard to FC531.FC1063sets the standard to FC1063.FC2125sets the standard to FC2125.FC4250sets the standard to FC4250.FC8500sets the standard to FC8500.ENET1000sets the standard to ENET1000.IBA2500sets the standard to IBA2500.IBA_GEN2sets the standard toIBA_GEN2.OC1sets the standard to OC1.OC3sets the standard to OC3.OC12sets the standard to OC12.OC48sets the standard to OC48.PCIE_GEN1sets the standard toPCIE_GEN1.PCIE_GEN2sets the standard toPCIE_GEN2.PCIE_GEN3sets the standard toPCIE_GEN3.RIO125sets the standard to RIO125.RIO250sets the standard to RIO250.RIO3125sets the standard to RIO3125.SAS15_NOSSCsets the standard toSAS15_NOSSC.SAS3_NOSSCsets the standard toSAS3_NOSSC.SAS6_NOSSCsets the standard toSAS6_NOSSC.SAS12_NOSSCsets the standard toSAS12_NOSSC.SAS15_SSCsets the standard toSAS15_SSC.SAS3_SSCsets the standard toSAS3_SSC.SAS6_SSCsets the standard toSAS6_SSC.SAS12_SSCsets the standard toSAS12_SSC.SATA_GEN1sets the standard toSATA_GEN1.SATA_GEN2sets the standard toSATA_GEN2.SATA_GEN3sets the standard toSATA_GEN3.USB3sets the standard to USB3.XAUIsets the standard to XAUI.XAUI_GEN2sets the standard toXAUI_GEN2.
Bases: SCPICmdWrite
The MEASUrement:DELete command.
Description
- The command deletes the specified measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:DELete valuecommand.
SCPI Syntax
- MEASUrement:DELete <QString>
Info
<QString>is the measurement to delete. Argument is of the form ‘MEAS’ where is ≥1.
Bases: SCPICmdWriteNoArguments
The MEASUrement:DELETEALL command.
Description
- This command deletes all the active instances of measurements defined in the scope application.
Usage
- Using the
.write()method will send theMEASUrement:DELETEALLcommand.
SCPI Syntax
- MEASUrement:DELETEALL
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:DIRacmodel command.
Description
- This command sets or queries the dirac model used to separate random from deterministic jitter for jitter measurements.
Usage
- Using the
.query()method will send theMEASUrement:DIRacmodel?query. - Using the
.verify(value)method will send theMEASUrement:DIRacmodel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:DIRacmodel valuecommand.
SCPI Syntax
- MEASUrement:DIRacmodel {PCIExpress|FIBREchannel}
- MEASUrement:DIRacmodel?
Info
PCIExpressspecifies the PCIExpress dirac model.FIBREchannelspecifies the FIBREchannel dirac model.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:DISPLAYUnits command.
Description
- This command sets or queries the display units used for jitter summary measurements.
Usage
- Using the
.query()method will send theMEASUrement:DISPLAYUnits?query. - Using the
.verify(value)method will send theMEASUrement:DISPLAYUnits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:DISPLAYUnits valuecommand.
SCPI Syntax
- MEASUrement:DISPLAYUnits {SEConds|UNITINtervals}
- MEASUrement:DISPLAYUnits?
Info
SECondsset the display units to seconds.UNITINtervalsset the display units to unit intervals.
Bases: ValidatedDynamicNumberCmd, SCPICmdWrite
The MEASUrement:EDGE<x> command.
Description
- This command sets or queries the type of the edge for the measurement.
Usage
- Using the
.write(value)method will send theMEASUrement:EDGE<x> valuecommand.
SCPI Syntax
- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
Info
FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both a rising and falling edge of the waveform.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:EYERENDER command.
Description
- This command sets or queries the state of high-performance eye rendering for an eye diagram.
Usage
- Using the
.query()method will send theMEASUrement:EYERENDER?query. - Using the
.verify(value)method will send theMEASUrement:EYERENDER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:EYERENDER valuecommand.
SCPI Syntax
- MEASUrement:EYERENDER {ON|OFF|<NR1>}
- MEASUrement:EYERENDER?
Info
<NR1>= 0 disables high-performance eye rendering for an eye diagram; any other value turns this feature on.OFFdisables high-performance eye rendering for an eye diagram.ONenables high-performance eye rendering for an eye diagram.
Bases: SCPICmdRead
The MEASUrement:FILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:FILTers?query. - Using the
.verify(value)method will send theMEASUrement:FILTers?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.blankingtime: TheMEASUrement:FILTers:BLANKingtimecommand..highpass: TheMEASUrement:FILTers:HIGHPasscommand tree..lowpass: TheMEASUrement:FILTers:LOWPasscommand tree..ramptime: TheMEASUrement:FILTers:RAMPtimecommand.
property
¶
blankingtime: MeasurementFiltersBlankingtime
Return the MEASUrement:FILTers:BLANKingtime command.
Description
- This command sets or queries the global filter blanking time.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:BLANKingtime?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:BLANKingtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:BLANKingtime valuecommand.
SCPI Syntax
- MEASUrement:FILTers:BLANKingtime <NR3>
- MEASUrement:FILTers:BLANKingtime?
Info
<NR3>is the current filter blanking time.
property
¶
highpass: MeasurementFiltersHighpass
Return the MEASUrement:FILTers:HIGHPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:HIGHPass?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:HIGHPass?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.freq: TheMEASUrement:FILTers:HIGHPass:FREQcommand..spec: TheMEASUrement:FILTers:HIGHPass:SPECcommand.
property
¶
lowpass: MeasurementFiltersLowpass
Return the MEASUrement:FILTers:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.freq: TheMEASUrement:FILTers:LOWPass:FREQcommand..spec: TheMEASUrement:FILTers:LOWPass:SPECcommand.
property
¶
ramptime: MeasurementFiltersRamptime
Return the MEASUrement:FILTers:RAMPtime command.
Description
- This command sets or queries the global filter ramp time for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:RAMPtime?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:RAMPtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:RAMPtime valuecommand.
SCPI Syntax
- MEASUrement:FILTers:RAMPtime <NR3>
- MEASUrement:FILTers:RAMPtime?
Info
<NR3>is the current filter ramp time.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:FILTers:BLANKingtime command.
Description
- This command sets or queries the global filter blanking time.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:BLANKingtime?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:BLANKingtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:BLANKingtime valuecommand.
SCPI Syntax
- MEASUrement:FILTers:BLANKingtime <NR3>
- MEASUrement:FILTers:BLANKingtime?
Info
<NR3>is the current filter blanking time.
Bases: SCPICmdRead
The MEASUrement:FILTers:HIGHPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:HIGHPass?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:HIGHPass?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.freq: TheMEASUrement:FILTers:HIGHPass:FREQcommand..spec: TheMEASUrement:FILTers:HIGHPass:SPECcommand.
property
¶
Return the MEASUrement:FILTers:HIGHPass:FREQ command.
Description
- This command sets or queries the global high pass filter frequency for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:HIGHPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:HIGHPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:HIGHPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:FILTers:HIGHPass:FREQ?
Info
<NR3>is the current high pass filter frequency.
property
¶
Return the MEASUrement:FILTers:HIGHPass:SPEC command.
Description
- This command sets or queries the global high pass filter order for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:HIGHPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:HIGHPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:HIGHPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:HIGHPass:SPEC?
Info
NONEspecifies no high pass filter.FIRSTspecifies a first order high pass filter.SECONDspecifies a second order high pass filter.THIRDspecifies a third order high pass filter.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:FILTers:HIGHPass:FREQ command.
Description
- This command sets or queries the global high pass filter frequency for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:HIGHPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:HIGHPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:HIGHPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:FILTers:HIGHPass:FREQ?
Info
<NR3>is the current high pass filter frequency.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:FILTers:HIGHPass:SPEC command.
Description
- This command sets or queries the global high pass filter order for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:HIGHPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:HIGHPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:HIGHPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:HIGHPass:SPEC?
Info
NONEspecifies no high pass filter.FIRSTspecifies a first order high pass filter.SECONDspecifies a second order high pass filter.THIRDspecifies a third order high pass filter.
Bases: SCPICmdRead
The MEASUrement:FILTers:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.freq: TheMEASUrement:FILTers:LOWPass:FREQcommand..spec: TheMEASUrement:FILTers:LOWPass:SPECcommand.
property
¶
Return the MEASUrement:FILTers:LOWPass:FREQ command.
Description
- This command sets or queries the global low pass filter cutoff frequency for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:FILTers:LOWPass:FREQ?
Info
<NR3>is the current low pass filter frequency.
property
¶
Return the MEASUrement:FILTers:LOWPass:SPEC command.
Description
- This command sets or queries the global low pass filter order for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:LOWPass:SPEC?
Info
NONEspecifies no low pass filter.FIRSTspecifies a first order low pass filter.SECONDspecifies a second order low pass filter.THIRDspecifies a third order low pass filter.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:FILTers:LOWPass:FREQ command.
Description
- This command sets or queries the global low pass filter cutoff frequency for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:FILTers:LOWPass:FREQ?
Info
<NR3>is the current low pass filter frequency.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:FILTers:LOWPass:SPEC command.
Description
- This command sets or queries the global low pass filter order for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:LOWPass:SPEC?
Info
NONEspecifies no low pass filter.FIRSTspecifies a first order low pass filter.SECONDspecifies a second order low pass filter.THIRDspecifies a third order low pass filter.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:FILTers:RAMPtime command.
Description
- This command sets or queries the global filter ramp time for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:FILTers:RAMPtime?query. - Using the
.verify(value)method will send theMEASUrement:FILTers:RAMPtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:FILTers:RAMPtime valuecommand.
SCPI Syntax
- MEASUrement:FILTers:RAMPtime <NR3>
- MEASUrement:FILTers:RAMPtime?
Info
<NR3>is the current filter ramp time.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing command.
Description
- This command sets or queries the global gating type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:GATing?query. - Using the
.verify(value)method will send theMEASUrement:GATing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing valuecommand.
SCPI Syntax
- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing?
Info
NONEturns off measurement gating.SCREenturns on gating, using the left and right edges of the screen.CURSorlimits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.LOGicspecifies that measurements are taken only on the portion of the waveform where the logic source is in the active state.SEARCHspecifies that measurements are taken based on search criteria.TIMelimits measurements to the portion of the waveform between the Start and End gate times.
Properties
.active: TheMEASUrement:GATing:ACTivecommand..endtime: TheMEASUrement:GATing:ENDtimecommand..hysteresis: TheMEASUrement:GATing:HYSTeresiscommand..logicsource: TheMEASUrement:GATing:LOGICSourcecommand..midref: TheMEASUrement:GATing:MIDRefcommand..searchsource: TheMEASUrement:GATing:SEARCHSourcecommand..starttime: TheMEASUrement:GATing:STARTtimecommand.
property
¶
active: MeasurementGatingActive
Return the MEASUrement:GATing:ACTive command.
Description
- This command sets or queries the global gating active level used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:ACTive?query. - Using the
.verify(value)method will send theMEASUrement:GATing:ACTive?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:ACTive valuecommand.
SCPI Syntax
- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?
Info
HIGHspecifies the gate is HIGH.LOWspecifies the gate is LOW.
property
¶
endtime: MeasurementGatingEndtime
Return the MEASUrement:GATing:ENDtime command.
Description
- Sets or queries the end gate time for all measurements that use Global gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:ENDtime?query. - Using the
.verify(value)method will send theMEASUrement:GATing:ENDtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:ENDtime valuecommand.
SCPI Syntax
- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?
Info
<NR3>is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.
property
¶
hysteresis: MeasurementGatingHysteresis
Return the MEASUrement:GATing:HYSTeresis command.
Description
- This command sets or queries the global gating hysteresis value used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:GATing:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?
Info
<NR3>is the gating hysteresis.
property
¶
logicsource: MeasurementGatingLogicsource
Return the MEASUrement:GATing:LOGICSource command.
Description
- This command sets or queries the gating data source used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:LOGICSource?query. - Using the
.verify(value)method will send theMEASUrement:GATing:LOGICSource?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:LOGICSource valuecommand.
SCPI Syntax
- MEASUrement:GATing:LOGICSource {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
midref: MeasurementGatingMidref
Return the MEASUrement:GATing:MIDRef command.
Description
- This command sets or queries the global gating mid ref value used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:MIDRef?query. - Using the
.verify(value)method will send theMEASUrement:GATing:MIDRef?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:MIDRef valuecommand.
SCPI Syntax
- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?
Info
<NR3>is the mid ref value for gating.
property
¶
searchsource: MeasurementGatingSearchsource
Return the MEASUrement:GATing:SEARCHSource command.
Description
- This command sets or queries the global gating search source when the gating type is search.
Usage
- Using the
.query()method will send theMEASUrement:GATing:SEARCHSource?query. - Using the
.verify(value)method will send theMEASUrement:GATing:SEARCHSource?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:SEARCHSource valuecommand.
SCPI Syntax
- MEASUrement:GATing:SEARCHSource SEARCH1
- MEASUrement:GATing:SEARCHSource?
property
¶
starttime: MeasurementGatingStarttime
Return the MEASUrement:GATing:STARTtime command.
Description
- Sets or queries the start gate time for all measurements that use Global gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:STARTtime?query. - Using the
.verify(value)method will send theMEASUrement:GATing:STARTtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:STARTtime valuecommand.
SCPI Syntax
- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?
Info
<NR3>is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing:ACTive command.
Description
- This command sets or queries the global gating active level used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:ACTive?query. - Using the
.verify(value)method will send theMEASUrement:GATing:ACTive?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:ACTive valuecommand.
SCPI Syntax
- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?
Info
HIGHspecifies the gate is HIGH.LOWspecifies the gate is LOW.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing:ENDtime command.
Description
- Sets or queries the end gate time for all measurements that use Global gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:ENDtime?query. - Using the
.verify(value)method will send theMEASUrement:GATing:ENDtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:ENDtime valuecommand.
SCPI Syntax
- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?
Info
<NR3>is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing:HYSTeresis command.
Description
- This command sets or queries the global gating hysteresis value used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:GATing:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?
Info
<NR3>is the gating hysteresis.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing:LOGICSource command.
Description
- This command sets or queries the gating data source used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:LOGICSource?query. - Using the
.verify(value)method will send theMEASUrement:GATing:LOGICSource?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:LOGICSource valuecommand.
SCPI Syntax
- MEASUrement:GATing:LOGICSource {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing:MIDRef command.
Description
- This command sets or queries the global gating mid ref value used for logic gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:MIDRef?query. - Using the
.verify(value)method will send theMEASUrement:GATing:MIDRef?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:MIDRef valuecommand.
SCPI Syntax
- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?
Info
<NR3>is the mid ref value for gating.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing:SEARCHSource command.
Description
- This command sets or queries the global gating search source when the gating type is search.
Usage
- Using the
.query()method will send theMEASUrement:GATing:SEARCHSource?query. - Using the
.verify(value)method will send theMEASUrement:GATing:SEARCHSource?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:SEARCHSource valuecommand.
SCPI Syntax
- MEASUrement:GATing:SEARCHSource SEARCH1
- MEASUrement:GATing:SEARCHSource?
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:GATing:STARTtime command.
Description
- Sets or queries the start gate time for all measurements that use Global gating.
Usage
- Using the
.query()method will send theMEASUrement:GATing:STARTtime?query. - Using the
.verify(value)method will send theMEASUrement:GATing:STARTtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:GATing:STARTtime valuecommand.
SCPI Syntax
- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?
Info
<NR3>is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.
Bases: SCPICmdRead
The MEASUrement:HIGHLEVel command tree.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.configuration: TheMEASUrement:HIGHLEVel:CONFIGurationcommand..edgequalifier: TheMEASUrement:HIGHLEVel:EDGEQUALifiercommand..inlowpass: TheMEASUrement:HIGHLEVel:INLOWPasscommand tree..l2ltol2n: TheMEASUrement:HIGHLEVel:L2LTOL2Ncommand..lineselected: TheMEASUrement:HIGHLEVel:LINESelectedcommand..outedgequalifier: TheMEASUrement:HIGHLEVel:OUTEDGEQUALifiercommand..outl2ltol2n: TheMEASUrement:HIGHLEVel:OUTL2LTOL2Ncommand..outlineselected: TheMEASUrement:HIGHLEVel:OUTLINESelectedcommand..outlowpass: TheMEASUrement:HIGHLEVel:OUTLOWPasscommand tree..outsource: TheMEASUrement:HIGHLEVel:OUTSOURCEcommand..outwiring: TheMEASUrement:HIGHLEVel:OUTWIRingcommand..source: TheMEASUrement:HIGHLEVel:SOURCEcommand..wiring: TheMEASUrement:HIGHLEVel:WIRingcommand.
property
¶
configuration: MeasurementHighlevelConfiguration
Return the MEASUrement:HIGHLEVel:CONFIGuration command.
Description
- This command sets or queries the global input and output configuration.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:CONFIGuration?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:CONFIGuration?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:CONFIGuration valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:HIGHLEVel:CONFIGuration?
Info
INPUTspecifies the source settings configuration as input.OUTPUTspecifies the source settings configuration as output.
property
¶
edgequalifier: MeasurementHighlevelEdgequalifier
Return the MEASUrement:HIGHLEVel:EDGEQUALifier command.
Description
- This command sets or queries global input edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:EDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:EDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:EDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:EDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:EDGEQUALifier?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
inlowpass: MeasurementHighlevelInlowpass
Return the MEASUrement:HIGHLEVel:INLOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:INLOWPass?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:INLOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.freq: TheMEASUrement:HIGHLEVel:INLOWPass:FREQcommand..spec: TheMEASUrement:HIGHLEVel:INLOWPass:SPECcommand.
property
¶
l2ltol2n: MeasurementHighlevelL2ltol2n
Return the MEASUrement:HIGHLEVel:L2LTOL2N command.
Description
- This command enables the Line-to-Line to Line-to-Neutral Conversion.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:L2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:L2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:L2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:L2LTOL2N?
property
¶
lineselected: MeasurementHighlevelLineselected
Return the MEASUrement:HIGHLEVel:LINESelected command.
Description
- This command sets or queries global input select lines.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:LINESelected?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:LINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:LINESelected valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:HIGHLEVel:LINESelected?
Info
ABCBspecifies the global input select lines as ABCB.ACBCspecifies the global input select lines as ACBC.BACAspecifies the global input select lines as BACA.ANspecifies the global input select lines as AN.BNspecifies the global input select lines as BN.CNspecifies the global input select lines as CN.
property
¶
outedgequalifier: MeasurementHighlevelOutedgequalifier
Return the MEASUrement:HIGHLEVel:OUTEDGEQUALifier command.
Description
- This command sets or queries global output edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTEDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTEDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTEDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
outl2ltol2n: MeasurementHighlevelOutl2ltol2n
Return the MEASUrement:HIGHLEVel:OUTL2LTOL2N command.
Description
- This command sets or queries global output Line-to-Line to Line-to-Neutral Conversion.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTL2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTL2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTL2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:OUTL2LTOL2N?
property
¶
outlineselected: MeasurementHighlevelOutlineselected
Return the MEASUrement:HIGHLEVel:OUTLINESelected command.
Description
- This command sets or queries global output select lines.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLINESelected?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTLINESelected valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:HIGHLEVel:OUTLINESelected?
Info
XYZYspecifies the global output select lines as XYZY.XZYZspecifies the global output select lines as XZYZ.YXZXspecifies the global output select lines as YXZX.XNspecifies the global output select lines as XN.YNspecifies the global output select lines as YN.ZNspecifies the global output select lines as ZN.
property
¶
outlowpass: MeasurementHighlevelOutlowpass
Return the MEASUrement:HIGHLEVel:OUTLOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLOWPass?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.freq: TheMEASUrement:HIGHLEVel:OUTLOWPass:FREQcommand..spec: TheMEASUrement:HIGHLEVel:OUTLOWPass:SPECcommand.
property
¶
outsource: MeasurementHighlevelOutsource
Return the MEASUrement:HIGHLEVel:OUTSOURCE command.
Description
- This command sets or queries global output source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTSOURCE?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTSOURCE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTSOURCE valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTSOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTSOURCE?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
outwiring: MeasurementHighlevelOutwiring
Return the MEASUrement:HIGHLEVel:OUTWIRing command.
Description
- This command sets or queries the global output wiring.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTWIRing?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTWIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTWIRing valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:HIGHLEVel:OUTWIRing?
Info
P1W2V1I1specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.P1W3V2I2specifies 1 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V2I2specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V3I3specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.P3W3specifies 3 phase and 3 wire, the 3rd wire being Neutral.DCP1W2specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.
property
¶
source: MeasurementHighlevelSource
Return the MEASUrement:HIGHLEVel:SOURCE command.
Description
- This command sets or queries global input source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:SOURCE?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:SOURCE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:SOURCE valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:SOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:SOURCE?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
wiring: MeasurementHighlevelWiring
Return the MEASUrement:HIGHLEVel:WIRing command.
Description
- This command sets or queries the wiring configuration for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:WIRing?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:WIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:WIRing valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:WIRing?
Info
P1W2V1I1specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.P1W3V2I2specifies 1 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V2I2specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V3I3specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.P3W3specifies 3 phase and 3 wire, the 3rd wire being Neutral.DCP1W2specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:CONFIGuration command.
Description
- This command sets or queries the global input and output configuration.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:CONFIGuration?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:CONFIGuration?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:CONFIGuration valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:HIGHLEVel:CONFIGuration?
Info
INPUTspecifies the source settings configuration as input.OUTPUTspecifies the source settings configuration as output.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:EDGEQUALifier command.
Description
- This command sets or queries global input edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:EDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:EDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:EDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:EDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:EDGEQUALifier?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdRead
The MEASUrement:HIGHLEVel:INLOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:INLOWPass?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:INLOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.freq: TheMEASUrement:HIGHLEVel:INLOWPass:FREQcommand..spec: TheMEASUrement:HIGHLEVel:INLOWPass:SPECcommand.
property
¶
Return the MEASUrement:HIGHLEVel:INLOWPass:FREQ command.
Description
- This command sets or queries global input low pass filter frequency.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:INLOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:INLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:INLOWPass:FREQ?
Info
<NR3>specifies the global input low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.
property
¶
Return the MEASUrement:HIGHLEVel:INLOWPass:SPEC command.
Description
- This command sets or queries global input low pass filter order.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:INLOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:INLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:INLOWPass:SPEC?
Info
NONEspecifies the global input low pass filter order as none.FIRSTspecifies the global input low pass filter order as first.SECONDspecifies the global input low pass filter order as second.THIRDspecifies the global input low pass filter order as third.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:INLOWPass:FREQ command.
Description
- This command sets or queries global input low pass filter frequency.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:INLOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:INLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:INLOWPass:FREQ?
Info
<NR3>specifies the global input low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:INLOWPass:SPEC command.
Description
- This command sets or queries global input low pass filter order.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:INLOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:INLOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:INLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:INLOWPass:SPEC?
Info
NONEspecifies the global input low pass filter order as none.FIRSTspecifies the global input low pass filter order as first.SECONDspecifies the global input low pass filter order as second.THIRDspecifies the global input low pass filter order as third.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:L2LTOL2N command.
Description
- This command enables the Line-to-Line to Line-to-Neutral Conversion.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:L2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:L2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:L2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:L2LTOL2N?
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:LINESelected command.
Description
- This command sets or queries global input select lines.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:LINESelected?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:LINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:LINESelected valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:HIGHLEVel:LINESelected?
Info
ABCBspecifies the global input select lines as ABCB.ACBCspecifies the global input select lines as ACBC.BACAspecifies the global input select lines as BACA.ANspecifies the global input select lines as AN.BNspecifies the global input select lines as BN.CNspecifies the global input select lines as CN.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:OUTEDGEQUALifier command.
Description
- This command sets or queries global output edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTEDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTEDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTEDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:OUTL2LTOL2N command.
Description
- This command sets or queries global output Line-to-Line to Line-to-Neutral Conversion.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTL2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTL2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTL2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:OUTL2LTOL2N?
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:OUTLINESelected command.
Description
- This command sets or queries global output select lines.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLINESelected?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTLINESelected valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:HIGHLEVel:OUTLINESelected?
Info
XYZYspecifies the global output select lines as XYZY.XZYZspecifies the global output select lines as XZYZ.YXZXspecifies the global output select lines as YXZX.XNspecifies the global output select lines as XN.YNspecifies the global output select lines as YN.ZNspecifies the global output select lines as ZN.
Bases: SCPICmdRead
The MEASUrement:HIGHLEVel:OUTLOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLOWPass?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.freq: TheMEASUrement:HIGHLEVel:OUTLOWPass:FREQcommand..spec: TheMEASUrement:HIGHLEVel:OUTLOWPass:SPECcommand.
property
¶
Return the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ command.
Description
- This command sets or queries global output low pass filter frequency.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ?
Info
<NR3>specifies the global output low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.
property
¶
Return the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC command.
Description
- This command sets or queries global output low pass filter order.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC?
Info
NONEspecifies the global output low pass filter order as none.FIRSTspecifies the global output low pass filter order as first.SECONDspecifies the global output low pass filter order as second.THIRDspecifies the global output low pass filter order as third.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:OUTLOWPass:FREQ command.
Description
- This command sets or queries global output low pass filter frequency.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ?
Info
<NR3>specifies the global output low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:OUTLOWPass:SPEC command.
Description
- This command sets or queries global output low pass filter order.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTLOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTLOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC?
Info
NONEspecifies the global output low pass filter order as none.FIRSTspecifies the global output low pass filter order as first.SECONDspecifies the global output low pass filter order as second.THIRDspecifies the global output low pass filter order as third.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:OUTSOURCE command.
Description
- This command sets or queries global output source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTSOURCE?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTSOURCE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTSOURCE valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTSOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTSOURCE?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:OUTWIRing command.
Description
- This command sets or queries the global output wiring.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:OUTWIRing?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:OUTWIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:OUTWIRing valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:HIGHLEVel:OUTWIRing?
Info
P1W2V1I1specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.P1W3V2I2specifies 1 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V2I2specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V3I3specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.P3W3specifies 3 phase and 3 wire, the 3rd wire being Neutral.DCP1W2specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:SOURCE command.
Description
- This command sets or queries global input source.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:SOURCE?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:SOURCE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:SOURCE valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:SOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:SOURCE?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:HIGHLEVel:WIRing command.
Description
- This command sets or queries the wiring configuration for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:HIGHLEVel:WIRing?query. - Using the
.verify(value)method will send theMEASUrement:HIGHLEVel:WIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:HIGHLEVel:WIRing valuecommand.
SCPI Syntax
- MEASUrement:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:WIRing?
Info
P1W2V1I1specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.P1W3V2I2specifies 1 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V2I2specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.P3W3V3I3specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.P3W3specifies 3 phase and 3 wire, the 3rd wire being Neutral.DCP1W2specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:INTERp command.
Description
- This command sets or queries the interpolation mode used to locate edge crossings.
Usage
- Using the
.query()method will send theMEASUrement:INTERp?query. - Using the
.verify(value)method will send theMEASUrement:INTERp?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:INTERp valuecommand.
SCPI Syntax
- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?
Info
AUTOautomatically selects the interpolation mode.SINXspecifies sin(x)/x interpolation, where acquired points are fit to a curve.LINearspecifies linear interpolation, where acquired points are connected with straight lines.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:JITTermodel command.
Description
- This command sets or queries the model used to separate random from deterministic jitter for jitter measurements.
Usage
- Using the
.query()method will send theMEASUrement:JITTermodel?query. - Using the
.verify(value)method will send theMEASUrement:JITTermodel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:JITTermodel valuecommand.
SCPI Syntax
- MEASUrement:JITTermodel {SPECTRAL|SPECTRALBUJ}
- MEASUrement:JITTermodel?
Info
SPECTRALsets the jitter separation model to spectral only.SPECTRALBUJsets the jitter separation model to spectral plus BUJ.
Bases: SCPICmdRead
The MEASUrement:LIST command.
Description
- This query returns a comma separated list of all currently defined measurements.
Usage
- Using the
.query()method will send theMEASUrement:LIST?query. - Using the
.verify(value)method will send theMEASUrement:LIST?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:LIST?
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:LOCKRJ command.
Description
- This command sets or queries the state of RJ locking.
Usage
- Using the
.query()method will send theMEASUrement:LOCKRJ?query. - Using the
.verify(value)method will send theMEASUrement:LOCKRJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:LOCKRJ valuecommand.
SCPI Syntax
- MEASUrement:LOCKRJ {ON|OFF|<NR1>}
- MEASUrement:LOCKRJ?
Info
MEAS<x>specifies the measurement number.ONindicates that RJ locking is active.OFFindicates that RJ locking is off.<NR1>a 0 turns off RJ locking; any other value activates RJ locking.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:LOCKRJValue command.
Description
- This command sets or queries the RJ lock value.
Usage
- Using the
.query()method will send theMEASUrement:LOCKRJValue?query. - Using the
.verify(value)method will send theMEASUrement:LOCKRJValue?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:LOCKRJValue valuecommand.
SCPI Syntax
- MEASUrement:LOCKRJValue <NR3>
- MEASUrement:LOCKRJValue?
Info
MEAS<x>specifies the measurement number.<NR3>default value = 1e-12; minimum value = 1e-15; maximum value = 1.
Bases: ValidatedDynamicNumberCmd, SCPICmdRead
The MEASUrement:MATH<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Properties
.reflevels: TheMEASUrement:MATH<x>:REFLevelscommand tree.
property
¶
reflevels: MeasurementMathItemReflevels
Return the MEASUrement:MATH<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Sub-properties
.absolute: TheMEASUrement:MATH<x>:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:MATH<x>:REFLevels:BASETopcommand..method: TheMEASUrement:MATH<x>:REFLevels:METHodcommand..percent: TheMEASUrement:MATH<x>:REFLevels:PERCentcommand tree.
Bases: SCPICmdRead
The MEASUrement:MATH<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Properties
.absolute: TheMEASUrement:MATH<x>:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:MATH<x>:REFLevels:BASETopcommand..method: TheMEASUrement:MATH<x>:REFLevels:METHodcommand..percent: TheMEASUrement:MATH<x>:REFLevels:PERCentcommand tree.
property
¶
absolute: MeasurementMathItemReflevelsAbsolute
Return the MEASUrement:MATH<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Sub-properties
.fallhigh: TheMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:MATH<x>:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:MATH<x>:REFLevels:ABSolute:TYPEcommand.
property
¶
basetop: MeasurementMathItemReflevelsBasetop
Return the MEASUrement:MATH<x>:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:BASETop valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?
Info
MATH<x>specifies the math number.AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?
Info
MATH<x>specifies the math number.PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:MATH<x>:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:MATH<x>:REFLevel:ABSolutecommands. This method is useful when precise values are required.
property
¶
percent: MeasurementMathItemReflevelsPercent
Return the MEASUrement:MATH<x>:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Sub-properties
.fallhigh: TheMEASUrement:MATH<x>:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:MATH<x>:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:MATH<x>:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:MATH<x>:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:MATH<x>:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:MATH<x>:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:MATH<x>:REFLevels:PERCent:TYPEcommand.
Bases: SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Properties
.fallhigh: TheMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:MATH<x>:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:MATH<x>:REFLevels:ABSolute:TYPEcommand.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?
Info
MATH<x>specifies the math number.<NR3>is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.
property
¶
hysteresis: MeasurementMathItemReflevelsAbsoluteHysteresis
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?
Info
MATH<x>specifies the math number.<NR3>is the hysteresis value used for the autoset.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?
Info
MATH<x>specifies the math number.<NR3>is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Absolute.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?
Info
MATH<x>specifies the math number.SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?
Info
MATH<x>specifies the math number.<NR3>is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?
Info
MATH<x>specifies the math number.<NR3>is the hysteresis value used for the autoset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?
Info
MATH<x>specifies the math number.<NR3>is the high reference level, and is the zero percent level whenMEASUrement:IMMed:REFLevel:METHodis set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?
Info
MATH<x>specifies the math number.<NR3>is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?
Info
MATH<x>specifies the math number.SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:BASETop valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?
Info
MATH<x>specifies the math number.AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?
Info
MATH<x>specifies the math number.PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:MATH<x>:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:MATH<x>:REFLevel:ABSolutecommands. This method is useful when precise values are required.
Bases: SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Info
MATH<x>specifies the math number.
Properties
.fallhigh: TheMEASUrement:MATH<x>:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:MATH<x>:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:MATH<x>:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:MATH<x>:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:MATH<x>:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:MATH<x>:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:MATH<x>:REFLevels:PERCent:TYPEcommand.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the high reference level when the measurement Ref level method is set to Percent.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
property
¶
hysteresis: MeasurementMathItemReflevelsPercentHysteresis
Return the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?
Info
MATH<x>specifies the math number.<NR3>is the hysteresis value used for the autoset.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
property
¶
Return the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.
Description
- This command specifies or queries the reference level percent type for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?
Info
MATH<x>specifies the math number.TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the high reference level when the measurement Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?
Info
MATH<x>specifies the math number.<NR3>is the hysteresis value used for the autoset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?
Info
MATH<x>specifies the math number.<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.
Description
- This command specifies or queries the reference level percent type for the measurement. The math number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MATH<x>:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MATH<x>:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?
Info
MATH<x>specifies the math number.TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: ValidatedDynamicNumberCmd, SCPICmdRead
The MEASUrement:MEAS<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.ber: TheMEASUrement:MEAS<x>:BERcommand..bin: TheMEASUrement:MEAS<x>:BINcommand..bitcfgmode: TheMEASUrement:MEAS<x>:BITCfgmodecommand..bitend: TheMEASUrement:MEAS<x>:BITEndcommand..bitpcnt: TheMEASUrement:MEAS<x>:BITPcntcommand..bitstart: TheMEASUrement:MEAS<x>:BITSTartcommand..bittype: TheMEASUrement:MEAS<x>:BITTypecommand..burstedgtype: TheMEASUrement:MEAS<x>:BURSTEDGTYPecommand..ccresults: TheMEASUrement:MEAS<x>:CCRESUltscommand tree..clockrecovery: TheMEASUrement:MEAS<x>:CLOCKRecoverycommand tree..commonmode: TheMEASUrement:MEAS<x>:COMMONModecommand tree..cover: TheMEASUrement:MEAS<x>:COVercommand..customlimitsfile: TheMEASUrement:MEAS<x>:CUSTOMLIMITSFilecommand..cyclemode: TheMEASUrement:MEAS<x>:CYCLemodecommand..delay: TheMEASUrement:MEAS<x>:DELaycommand tree..displaystat: TheMEASUrement:MEAS<x>:DISPlaystatcommand tree..edge: TheMEASUrement:MEAS<x>:EDGE<x>command..edgeincre: TheMEASUrement:MEAS<x>:EDGEIncrecommand..edgequalone: TheMEASUrement:MEAS<x>:EDGEQUALONEcommand..edgequaltwo: TheMEASUrement:MEAS<x>:EDGEQUALTWOcommand..edgequalifier: TheMEASUrement:MEAS<x>:EDGEQUALifiercommand..edges: TheMEASUrement:MEAS<x>:EDGEScommand tree..eequal: TheMEASUrement:MEAS<x>:EEQUalcommand..failcount: TheMEASUrement:MEAS<x>:FAILCountcommand..filterrangefrom: TheMEASUrement:MEAS<x>:FILTERRANGEFROMcommand..filterrangeto: TheMEASUrement:MEAS<x>:FILTERRANGETOcommand..filters: TheMEASUrement:MEAS<x>:FILTerscommand tree..freq: TheMEASUrement:MEAS<x>:FREQcommand..fromedgesearchdirect: TheMEASUrement:MEAS<x>:FROMEDGESEARCHDIRectcommand..fromsymbol: TheMEASUrement:MEAS<x>:FROMSymbolcommand tree..fromedge: TheMEASUrement:MEAS<x>:FROMedgecommand..fundcurrent: TheMEASUrement:MEAS<x>:FUNDCURRentcommand..gating: TheMEASUrement:MEAS<x>:GATingcommand..globalref: TheMEASUrement:MEAS<x>:GLOBalrefcommand..harmonicsclass: TheMEASUrement:MEAS<x>:HARMONICSCLasscommand..harmonicssource: TheMEASUrement:MEAS<x>:HARMONICSSOURcecommand..harmonicsstd: TheMEASUrement:MEAS<x>:HARMONICSStdcommand..harmonicsunits: TheMEASUrement:MEAS<x>:HARMONICSUNitscommand..highlevel: TheMEASUrement:MEAS<x>:HIGHLEVelcommand tree..highrefvoltage: TheMEASUrement:MEAS<x>:HIGHREFVoltagecommand..hlevel: TheMEASUrement:MEAS<x>:HLEVelcommand tree..htorque: TheMEASUrement:MEAS<x>:HTORquecommand..hvoltage: TheMEASUrement:MEAS<x>:HVOLtagecommand..idletime: TheMEASUrement:MEAS<x>:IDLETimecommand..inputlevel: TheMEASUrement:MEAS<x>:INPUTLEVelcommand..inputpower: TheMEASUrement:MEAS<x>:INPUTPOwercommand..jittersummary: TheMEASUrement:MEAS<x>:JITTERSummarycommand tree..label: TheMEASUrement:MEAS<x>:LABelcommand..lineselected: TheMEASUrement:MEAS<x>:LINESelectedcommand..lowrefvoltage: TheMEASUrement:MEAS<x>:LOWREFVoltagecommand..ltorque: TheMEASUrement:MEAS<x>:LTORquecommand..ltype: TheMEASUrement:MEAS<x>:LTYPecommand..lunits: TheMEASUrement:MEAS<x>:LUNITscommand..lvoltage: TheMEASUrement:MEAS<x>:LVOLtagecommand..maxcurrent: TheMEASUrement:MEAS<x>:MAXCUrrentcommand..maxcycle: TheMEASUrement:MEAS<x>:MAXCyclecommand..maxgvoltage: TheMEASUrement:MEAS<x>:MAXGVoltagecommand..maxvoltage: TheMEASUrement:MEAS<x>:MAXVoltagecommand..measrange: TheMEASUrement:MEAS<x>:MEASRangecommand tree..mech: TheMEASUrement:MEAS<x>:MECHcommand tree..mincycle: TheMEASUrement:MEAS<x>:MINCyclecommand..oddeven: TheMEASUrement:MEAS<x>:ODDEVencommand..ofilters: TheMEASUrement:MEAS<x>:OFILterscommand tree..osangle: TheMEASUrement:MEAS<x>:OSANglecommand..outedgequalifier: TheMEASUrement:MEAS<x>:OUTEDGEQUALifiercommand..outfilters: TheMEASUrement:MEAS<x>:OUTFILTerscommand tree..outputvoltage: TheMEASUrement:MEAS<x>:OUTPUT<n>VOLTagecommand..passfailenabled: TheMEASUrement:MEAS<x>:PASSFAILENabledcommand..passfailhighlimit: TheMEASUrement:MEAS<x>:PASSFAILHIGHlimitcommand..passfaillimit: TheMEASUrement:MEAS<x>:PASSFAILLIMitcommand..passfaillowlimit: TheMEASUrement:MEAS<x>:PASSFAILLOWlimitcommand..passfailmargin: TheMEASUrement:MEAS<x>:PASSFAILMARgincommand..passfailwhen: TheMEASUrement:MEAS<x>:PASSFAILWHENcommand..patterndetection: TheMEASUrement:MEAS<x>:PATTERNDETECTIONcommand..patternlength: TheMEASUrement:MEAS<x>:PATTERNLENgthcommand..patterntype: TheMEASUrement:MEAS<x>:PATTERNTYPecommand..pcount: TheMEASUrement:MEAS<x>:PCOUNtcommand..perfreq: TheMEASUrement:MEAS<x>:PERFREQcommand tree..polarity: TheMEASUrement:MEAS<x>:POLaritycommand..population: TheMEASUrement:MEAS<x>:POPUlationcommand tree..powerfactor: TheMEASUrement:MEAS<x>:POWERFACtorcommand..pregion: TheMEASUrement:MEAS<x>:PREGioncommand..pwidth: TheMEASUrement:MEAS<x>:PWIDthcommand..redge: TheMEASUrement:MEAS<x>:REDGecommand..reflevels: TheMEASUrement:MEAS<x>:REFLevelscommand tree..reflevels1: TheMEASUrement:MEAS<x>:REFLevels1command tree..refmode: TheMEASUrement:MEAS<x>:REFModecommand..refvoltageval: TheMEASUrement:MEAS<x>:REFVOLTAGE<n>Valcommand..refvoltage: TheMEASUrement:MEAS<x>:REFVoltagecommand..results: TheMEASUrement:MEAS<x>:RESUltscommand tree..ripplefreqval: TheMEASUrement:MEAS<x>:RIPPLEFREQ<n>Valcommand..sequence: TheMEASUrement:MEAS<x>:SEQuencecommand..signalfrequency: TheMEASUrement:MEAS<x>:SIGNALFREQUEncycommand..signaltype: TheMEASUrement:MEAS<x>:SIGNALTypecommand..slabs: TheMEASUrement:MEAS<x>:SLABscommand..slpct: TheMEASUrement:MEAS<x>:SLPCtcommand..sltype: TheMEASUrement:MEAS<x>:SLTYpecommand..smoothingfilter: TheMEASUrement:MEAS<x>:SMOOTHINGFILTERcommand..source: TheMEASUrement:MEAS<x>:SOURCEcommand..source1: TheMEASUrement:MEAS<x>:SOUrce1command..ssc: TheMEASUrement:MEAS<x>:SSCcommand tree..status: TheMEASUrement:MEAS<x>:STATUScommand..stlabs: TheMEASUrement:MEAS<x>:STLABscommand..stlpct: TheMEASUrement:MEAS<x>:STLPctcommand..stype: TheMEASUrement:MEAS<x>:STYPecommand..sunits: TheMEASUrement:MEAS<x>:SUNitscommand..tckavg: TheMEASUrement:MEAS<x>:TCKAVGcommand..tconstant: TheMEASUrement:MEAS<x>:TCONstantcommand..timingmode: TheMEASUrement:MEAS<x>:TIMINGModecommand..tmethod: TheMEASUrement:MEAS<x>:TMEThodcommand..toedgesearchdirect: TheMEASUrement:MEAS<x>:TOEDGESEARCHDIRectcommand..toedge: TheMEASUrement:MEAS<x>:TOEdgecommand..tosymbol: TheMEASUrement:MEAS<x>:TOSYmbolcommand tree..transition: TheMEASUrement:MEAS<x>:TRANSitioncommand..type: TheMEASUrement:MEAS<x>:TYPecommand..waittime: TheMEASUrement:MEAS<x>:WAITTimecommand..windowlength: TheMEASUrement:MEAS<x>:WINDOWLENgthcommand..xunit: TheMEASUrement:MEAS<x>:XUNITcommand..yunit: TheMEASUrement:MEAS<x>:YUNITcommand..stltype: TheMEASUrement:MEAS<x>:STLTYpecommand.
property
¶
Return the MEASUrement:MEAS<x>:BER command.
Description
- This command sets or queries BER value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BER <NR3>
- MEASUrement:MEAS<x>:BER?
Info
MEAS<x>specifies the measurement number.<NR3>is BER value for the measurement.
Sub-properties
.targetber: TheMEASUrement:MEAS<x>:BER:TARGETBERcommand.
property
¶
Return the MEASUrement:MEAS<x>:BIN command.
Description
- This command sets or queries the bin count for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BIN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BIN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BIN valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BIN <NR3>
- MEASUrement:MEAS<x>:BIN?
Info
MEAS<x>specifies the measurement number.<NR3>is the bin count.
property
¶
bitcfgmode: MeasurementMeasItemBitcfgmode
Return the MEASUrement:MEAS<x>:BITCfgmode command.
Description
- This command sets or queries whether the measurement returns the mean or mode statistic result when the measurement type is bit amplitude/high/low. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITCfgmode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITCfgmode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITCfgmode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITCfgmode {MEAN|MODE}
- MEASUrement:MEAS<x>:BITCfgmode?
Info
MEAS<x>specifies the measurement number.MEANspecifies that the measurement returns results for each bit.MODEspecifies that the measurement returns the mode of its results.
property
¶
bitend: MeasurementMeasItemBitend
Return the MEASUrement:MEAS<x>:BITEnd command.
Description
- This command sets or queries the bit end as a percentage of the unit interval. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITEnd?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITEnd?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITEnd valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITEnd <NR3>
- MEASUrement:MEAS<x>:BITEnd?
Info
MEAS<x>specifies the measurement number.<NR3>is the bit end.
property
¶
bitpcnt: MeasurementMeasItemBitpcnt
Return the MEASUrement:MEAS<x>:BITPcnt command.
Description
- This command sets or queries the bit center as a percentage of the unit interval. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITPcnt?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITPcnt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITPcnt valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITPcnt <NR3>
- MEASUrement:MEAS<x>:BITPcnt?
Info
MEAS<x>specifies the measurement number.<NR3>is the bit center percentage value to be measured for the bit type selected.
property
¶
bitstart: MeasurementMeasItemBitstart
Return the MEASUrement:MEAS<x>:BITSTart command.
Description
- This command sets or queries the bit start as a percentage of the unit interval. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITSTart?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITSTart?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITSTart valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITSTart <NR3>
- MEASUrement:MEAS<x>:BITSTart?
Info
MEAS<x>specifies the measurement number.<NR3>is the bit start.
property
¶
bittype: MeasurementMeasItemBittype
Return the MEASUrement:MEAS<x>:BITType command.
Description
- This command sets or queries the bit type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITType?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITType?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITType valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- MEASUrement:MEAS<x>:BITType?
Info
MEAS<x>specifies the measurement number.ALLBitsspecifies that the measurement returns results for all bits.TRANSitionspecifies that the measurement returns results for transitions bit only.NONTRANsitionspecifies that the measurement returns results for non-transition bits only.
property
¶
burstedgtype: MeasurementMeasItemBurstedgtype
Return the MEASUrement:MEAS<x>:BURSTEDGTYPe command.
Description
- This command sets or queries the burst edge type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BURSTEDGTYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BURSTEDGTYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BURSTEDGTYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?
Info
MEAS<x>specifies the measurement number.RISEspecifies a burst with a rising edge.FALLspecifies a burst with a falling edge.
property
¶
ccresults: MeasurementMeasItemCcresults
Return the MEASUrement:MEAS<x>:CCRESUlts command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.allacqs: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqscommand tree..currentacq: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacqcommand tree.
property
¶
clockrecovery: MeasurementMeasItemClockrecovery
Return the MEASUrement:MEAS<x>:CLOCKRecovery command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.advanced: TheMEASUrement:MEAS<x>:CLOCKRecovery:ADVancedcommand tree..clockfrequency: TheMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequencycommand..clockmultiplier: TheMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultipliercommand..constclockmode: TheMEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODecommand..damping: TheMEASUrement:MEAS<x>:CLOCKRecovery:DAMPingcommand..datapath: TheMEASUrement:MEAS<x>:CLOCKRecovery:DATAPathcommand..datarate: TheMEASUrement:MEAS<x>:CLOCKRecovery:DATARatecommand..explicitclockmode: TheMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODecommand..global: TheMEASUrement:MEAS<x>:CLOCKRecovery:GLOBalcommand..jtfbandwidth: TheMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidthcommand..loopbandwidth: TheMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidthcommand..meanautocalculate: TheMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculatecommand..method: TheMEASUrement:MEAS<x>:CLOCKRecovery:METHodcommand..model: TheMEASUrement:MEAS<x>:CLOCKRecovery:MODelcommand..nominaloffset: TheMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFsetcommand..standard: TheMEASUrement:MEAS<x>:CLOCKRecovery:STAndardcommand.
property
¶
commonmode: MeasurementMeasItemCommonmode
Return the MEASUrement:MEAS<x>:COMMONMode command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.filters: TheMEASUrement:MEAS<x>:COMMONMode:FILTerscommand tree..sources: TheMEASUrement:MEAS<x>:COMMONMode:SOURCEscommand.
property
¶
cover: MeasurementMeasItemCover
Return the MEASUrement:MEAS<x>:COVer command.
Description
- This command sets or queries the Calculate Over for the Power Quality measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COVer?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COVer?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:COVer valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:COVer {FFREQuency|AFREQuencies}
- MEASUrement:MEAS<x>:COVer?
Info
FFREQuencysets Calculate Power Quality measurement.AFREQuenciessets Calculate Power Quality measurement for all frequencies.
property
¶
customlimitsfile: MeasurementMeasItemCustomlimitsfile
Return the MEASUrement:MEAS<x>:CUSTOMLIMITSFile command.
Description
- This command sets or queries the custom limits file path for custom harmonics standard. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CUSTOMLIMITSFile?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CUSTOMLIMITSFile?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CUSTOMLIMITSFile valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile <Qstring>
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile?
Info
MEAS<x>specifies the measurement number.<Qstring>specifies the location of limits file.
property
¶
cyclemode: MeasurementMeasItemCyclemode
Return the MEASUrement:MEAS<x>:CYCLemode command.
Description
- This command sets or queries the cycle mode for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CYCLemode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CYCLemode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CYCLemode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CYCLemode {RECORD|CYCLE}
- MEASUrement:MEAS<x>:CYCLemode?
Info
MEAS<x>specifies the measurement number.RECORDspecifies that the measurement is taken over the whole record.CYCLEspecifies that measurements are taken on each cycle of the source.
property
¶
delay: MeasurementMeasItemDelay
Return the MEASUrement:MEAS<x>:DELay command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DELay?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DELay?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.edge: TheMEASUrement:MEAS<x>:DELay:EDGE<x>command.
property
¶
displaystat: MeasurementMeasItemDisplaystat
Return the MEASUrement:MEAS<x>:DISPlaystat command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DISPlaystat?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DISPlaystat?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.enable: TheMEASUrement:MEAS<x>:DISPlaystat:ENABlecommand.
property
¶
edge: dict[int, MeasurementMeasItemEdgeItem]
Return the MEASUrement:MEAS<x>:EDGE<x> command.
Description
- This command sets or queries the type of the specified edge, rise or fall, for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGE<x> valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
Info
MEAS<x>specifies the measurement number.RISEspecifies the rising edge.FALLspecifies the falling edge.BOTHspecifies either the rising or falling edge.
property
¶
edgeincre: MeasurementMeasItemEdgeincre
Return the MEASUrement:MEAS<x>:EDGEIncre command.
Description
- This command sets or queries the edge increment value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEIncre?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEIncre?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEIncre valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?
Info
MEAS<x>specifies the measurement number.<NR3>is the measurements edge increment value.
property
¶
edgequalifier: MeasurementMeasItemEdgequalifier
Return the MEASUrement:MEAS<x>:EDGEQUALifier command.
Description
- This command sets or queries the edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:EDGEQUALifier?
Info
MEAS<x>is the measurement number.CH<x>is the edge qualifier source channel.MATH<x>is the edge qualifier source math waveform;is ≥1. REF<x>is the edge qualifier source reference waveform;is ≥1.
property
¶
edgequalone: MeasurementMeasItemEdgequalone
Return the MEASUrement:MEAS<x>:EDGEQUALONE command.
Description
- This command set or queries the measurement 1 input edge qualifier one source for Efficiency measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEQUALONE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEQUALONE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEQUALONE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEQUALONE <Qstring>
- MEASUrement:MEAS<x>:EDGEQUALONE?
Info
MEAS<x>is the measurement number.<Qstring>specifies the edge qualifier source at input configuration.
property
¶
edgequaltwo: MeasurementMeasItemEdgequaltwo
Return the MEASUrement:MEAS<x>:EDGEQUALTWO command.
Description
- This command sets or queries the measurement 1 output edge qualifier two source for Efficiency measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEQUALTWO?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEQUALTWO?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEQUALTWO valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEQUALTWO <Qstring>
- MEASUrement:MEAS<x>:EDGEQUALTWO?
Info
MEAS<x>is the measurement number.<Qstring>specifies the edge qualifier source at output configuration.
property
¶
edges: MeasurementMeasItemEdges
Return the MEASUrement:MEAS<x>:EDGES command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.fromlevel: TheMEASUrement:MEAS<x>:EDGES:FROMLevelcommand..level: TheMEASUrement:MEAS<x>:EDGES:LEVelcommand..lowerfrequency: TheMEASUrement:MEAS<x>:EDGES:LOWERFREQuencycommand..n: TheMEASUrement:MEAS<x>:EDGES:Ncommand..slewratemethod: TheMEASUrement:MEAS<x>:EDGES:SLEWRATEMethodcommand..tolevel: TheMEASUrement:MEAS<x>:EDGES:TOLevelcommand..upperfrequency: TheMEASUrement:MEAS<x>:EDGES:UPPERFREQuencycommand.
property
¶
eequal: MeasurementMeasItemEequal
Return the MEASUrement:MEAS<x>:EEQUal command.
Description
- This command turns on or off the edge qualifier settings as input waveform to measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EEQUal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EEQUal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EEQUal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EEQUal {ON|OFF}
- MEASUrement:MEAS<x>:EEQUal?
Info
MEAS<x>specifies the measurement number.ONspecifies the edge qualifier settings has been turned on.OFFspecifies the edge qualifier settings has been turned off.
property
¶
failcount: MeasurementMeasItemFailcount
Return the MEASUrement:MEAS<x>:FAILCount command.
Description
- This command returns the number of measurement failures, if applicable, for the selected measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FAILCount?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FAILCount?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:FAILCount?
property
¶
filterrangefrom: MeasurementMeasItemFilterrangefrom
Return the MEASUrement:MEAS<x>:FILTERRANGEFROM command.
Description
- This command sets or queries harmonics filter from order. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTERRANGEFROM?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTERRANGEFROM?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTERRANGEFROM valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTERRANGEFROM <NR3>
- MEASUrement:MEAS<x>:FILTERRANGEFROM?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the filter range from value. The default value is 1.
property
¶
filterrangeto: MeasurementMeasItemFilterrangeto
Return the MEASUrement:MEAS<x>:FILTERRANGETO command.
Description
- This command sets or queries harmonics filter to order. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTERRANGETO?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTERRANGETO?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTERRANGETO valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTERRANGETO <NR3>
- MEASUrement:MEAS<x>:FILTERRANGETO?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the filter range to value. The default value is 50.
property
¶
filters: MeasurementMeasItemFilters
Return the MEASUrement:MEAS<x>:FILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.blankingtime: TheMEASUrement:MEAS<x>:FILTers:BLANKingtimecommand..global: TheMEASUrement:MEAS<x>:FILTers:GLOBalcommand..highpass: TheMEASUrement:MEAS<x>:FILTers:HIGHPasscommand tree..lowpass: TheMEASUrement:MEAS<x>:FILTers:LOWPasscommand tree..ramptime: TheMEASUrement:MEAS<x>:FILTers:RAMPtimecommand.
property
¶
freq: MeasurementMeasItemFreq
Return the MEASUrement:MEAS<x>:FREQ command.
Description
- This command sets or queries switching frequency for Switching Ripple measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FREQ <NR3>
- MEASUrement:MEAS<x>:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the switching frequency. The default is 100k Hz, The minimum is 50 Hz, and the maximum is 1 GHz.
property
¶
fromedge: MeasurementMeasItemFromedge
Return the MEASUrement:MEAS<x>:FROMedge command.
Description
- This command sets or queries the from edge type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMedge?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMedge?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMedge valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?
Info
MEAS<x>specifies the measurement number.FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both the rising and falling edges of the waveform.
property
¶
fromedgesearchdirect: MeasurementMeasItemFromedgesearchdirect
Return the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.
Description
- This command sets or queries the from edge search direction for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMEDGESEARCHDIRect valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?
Info
MEAS<x>specifies the measurement number.FORWardspecifies a forward search from the edge.BACKWardspecifies a backward search from the edge.
property
¶
fromsymbol: MeasurementMeasItemFromsymbol
Return the MEASUrement:MEAS<x>:FROMSymbol command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.logic2source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrcecommand..logic3source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrcecommand..logic4source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrcecommand..logic5source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrcecommand..measureat: TheMEASUrement:MEAS<x>:FROMSymbol:MEASUREATcommand.
property
¶
fundcurrent: MeasurementMeasItemFundcurrent
Return the MEASUrement:MEAS<x>:FUNDCURRent command.
Description
- This command sets or queries the fundamental current value for IEC-Class C type harmonics standard. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FUNDCURRent?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FUNDCURRent?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FUNDCURRent valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FUNDCURRent <NR3>
- MEASUrement:MEAS<x>:FUNDCURRent?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the fundamental current for class C harmonics standard.
property
¶
gating: MeasurementMeasItemGating
Return the MEASUrement:MEAS<x>:GATing command.
Description
- This command sets or queries the gating type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing?
Info
MEAS<x>is the measurement number for which to return a value.NONEspecifies measurements are taken across the entire record.SCREENturns on gating, using the left and right edges of the screen.CURSorlimits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.LOGicspecifies that measurements are taken only when the logical state of other waveforms is true.SEARchspecifies that measurements are taken only where the results of a user specified search are found.TIMelimits measurements to the portion of the waveform between the Start and End gate times.
Sub-properties
.active: TheMEASUrement:MEAS<x>:GATing:ACTivecommand..endtime: TheMEASUrement:MEAS<x>:GATing:ENDtimecommand..global: TheMEASUrement:MEAS<x>:GATing:GLOBalcommand..hysteresis: TheMEASUrement:MEAS<x>:GATing:HYSTeresiscommand..logicsource: TheMEASUrement:MEAS<x>:GATing:LOGICSourcecommand..midref: TheMEASUrement:MEAS<x>:GATing:MIDRefcommand..searchsource: TheMEASUrement:MEAS<x>:GATing:SEARCHSourcecommand..starttime: TheMEASUrement:MEAS<x>:GATing:STARTtimecommand.
property
¶
globalref: MeasurementMeasItemGlobalref
Return the MEASUrement:MEAS<x>:GLOBalref command.
Description
- This command sets or queries the reference levels global flag for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GLOBalref?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GLOBalref?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GLOBalref valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?
Info
MEAS<x>specifies the measurement number.OFFallows ref levels to be set separately for each measurement.ONapplies the same ref levels to all measurements.0allows ref levels to be set separately for each measurement.1applies the same ref levels to all measurements.
property
¶
harmonicsclass: MeasurementMeasItemHarmonicsclass
Return the MEASUrement:MEAS<x>:HARMONICSCLass command.
Description
- This command sets or queries the class type for the harmonics measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSCLass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSCLass?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSCLass valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSCLass {CLASSA|CLASSB|CLASSC|CLASSD}
- MEASUrement:MEAS<x>:HARMONICSCLass?
Info
MEAS<x>specifies the measurement number.CLASSA-Dspecifies the class type.
property
¶
harmonicssource: MeasurementMeasItemHarmonicssource
Return the MEASUrement:MEAS<x>:HARMONICSSOURce command.
Description
- This command sets or queries harmonics source. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSSOURce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSSOURce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSSOURce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSSOURce {CURRENT|VOLTAGE}
- MEASUrement:MEAS<x>:HARMONICSSOURce?
Info
MEAS<x>specifies the measurement number.CURRENTspecifies current as the harmonics source.VOLTAGEspecifies voltage as the harmonics source.
property
¶
harmonicsstd: MeasurementMeasItemHarmonicsstd
Return the MEASUrement:MEAS<x>:HARMONICSStd command.
Description
- This command sets or queries harmonics standard. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSStd?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSStd?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSStd valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSStd {NONE|IEC|IEEE519|CUSTOM}
- MEASUrement:MEAS<x>:HARMONICSStd?
Info
MEAS<x>specifies the measurement number.NONEspecifies none as the harmonics test standard.IECspecifies IEC as the harmonics test standard.IEEE519specifies IEEE519 as the harmonics test standard.CUSTOMspecifies that there is a custom harmonics test standard.
property
¶
harmonicsunits: MeasurementMeasItemHarmonicsunits
Return the MEASUrement:MEAS<x>:HARMONICSUNits command.
Description
- This command sets or queries harmonics units. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSUNits?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSUNits valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSUNits {LOGARITHM|LINEAR}
- MEASUrement:MEAS<x>:HARMONICSUNits?
Info
MEAS<x>specifies the measurement number.LOGARITHMspecifies logarithmic as the harmonics units.LINEARspecifies linear as the harmonics units.
property
¶
highlevel: MeasurementMeasItemHighlevel
Return the MEASUrement:MEAS<x>:HIGHLEVel command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.configuration: TheMEASUrement:MEAS<x>:HIGHLEVel:CONFIGurationcommand..l2ltol2n: TheMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2Ncommand..lineselected: TheMEASUrement:MEAS<x>:HIGHLEVel:LINESelectedcommand..outl2ltol2n: TheMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2Ncommand..outlineselected: TheMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelectedcommand..outwiring: TheMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRingcommand..useglobal: TheMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBALcommand..wiring: TheMEASUrement:MEAS<x>:HIGHLEVel:WIRingcommand.
property
¶
highrefvoltage: MeasurementMeasItemHighrefvoltage
Return the MEASUrement:MEAS<x>:HIGHREFVoltage command.
Description
- This command sets or queries the high reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHREFVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHREFVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHREFVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?
Info
MEAS<x>specifies the measurement number.<NR3>is the high reference voltage value for the selected configuration.
property
¶
hlevel: MeasurementMeasItemHlevel
Return the MEASUrement:MEAS<x>:HLEVel command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HLEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HLEVel?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.output: TheMEASUrement:MEAS<x>:HLEVel:OUTPutcommand tree.
property
¶
htorque: MeasurementMeasItemHtorque
Return the MEASUrement:MEAS<x>:HTORque command.
Description
- This command sets or queries the measurement High Torque value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HTORque?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HTORque?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HTORque valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HTORque <NR1>
- MEASUrement:MEAS<x>:HTORque?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the High Torque value of the measurement in the range of 11 to 10000000.
property
¶
hvoltage: MeasurementMeasItemHvoltage
Return the MEASUrement:MEAS<x>:HVOLtage command.
Description
- This command sets or queries the measurement Torque High Voltage value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HVOLtage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HVOLtage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HVOLtage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HVOLtage <NR1>
- MEASUrement:MEAS<x>:HVOLtage?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the High Voltage value of the measurement in the range of 1 to 100.
property
¶
idletime: MeasurementMeasItemIdletime
Return the MEASUrement:MEAS<x>:IDLETime command.
Description
- This command sets or queries the idle time for the measurement when the measurement type is burst width. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:IDLETime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:IDLETime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:IDLETime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?
Info
MEAS<x>specifies the measurement number.<NR3>is the idle time.
property
¶
inputlevel: MeasurementMeasItemInputlevel
Return the MEASUrement:MEAS<x>:INPUTLEVel command.
Description
- Sets or queries the input trigger voltage level.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:INPUTLEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:INPUTLEVel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:INPUTLEVel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:INPUTLEVel <NR2>
- MEASUrement:MEAS<x>:INPUTLEVel?
Info
MEAS<x>is the measurement number.<NR2>is the trigger voltage, in the range of -500 V to +500 V.
property
¶
inputpower: MeasurementMeasItemInputpower
Return the MEASUrement:MEAS<x>:INPUTPOwer command.
Description
- This command sets or queries the input power value for IEC-Class C and Class D harmonics standard .
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:INPUTPOwer?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:INPUTPOwer?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:INPUTPOwer valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:INPUTPOwer <NR3>
- MEASUrement:MEAS<x>:INPUTPOwer?
Info
MEAS<x>is the measurement number.<NR3>specifies the input power value for class C harmonics standard.
property
¶
jittersummary: MeasurementMeasItemJittersummary
Return the MEASUrement:MEAS<x>:JITTERSummary command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.dcd: TheMEASUrement:MEAS<x>:JITTERSummary:DCDcommand..ddj: TheMEASUrement:MEAS<x>:JITTERSummary:DDJcommand..djdd: TheMEASUrement:MEAS<x>:JITTERSummary:DJDDcommand..eyewidthber: TheMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBERcommand..npj: TheMEASUrement:MEAS<x>:JITTERSummary:NPJcommand..pj: TheMEASUrement:MEAS<x>:JITTERSummary:PJcommand..rjdd: TheMEASUrement:MEAS<x>:JITTERSummary:RJDDcommand..tie: TheMEASUrement:MEAS<x>:JITTERSummary:TIEcommand..tjber: TheMEASUrement:MEAS<x>:JITTERSummary:TJBERcommand.
property
¶
label: MeasurementMeasItemLabel
Return the MEASUrement:MEAS<x>:LABel command.
Description
- This command sets or queries the label for the measurement. As the label can contain non 7-bit ASCII text, it is stored in Percent Encoding format. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:LABel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LABel <QString>
Info
MEAS<x>specifies the measurement number.<QString>is the measurement label.
property
¶
lineselected: MeasurementMeasItemLineselected
Return the MEASUrement:MEAS<x>:LINESelected command.
Description
- This command sets or queries selected lines for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LINESelected?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LINESelected valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LINESelected {ABCB|ACBC|BACA|XYZY|XZYZ|YXZX}
- MEASUrement:MEAS<x>:LINESelected?
Info
MEAS<x>specifies the measurement number.
property
¶
lowrefvoltage: MeasurementMeasItemLowrefvoltage
Return the MEASUrement:MEAS<x>:LOWREFVoltage command.
Description
- This command sets or queries the low reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LOWREFVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LOWREFVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LOWREFVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?
Info
MEAS<x>specifies the measurement number.<NR3>is the low reference voltage value for the selected configuration.
property
¶
ltorque: MeasurementMeasItemLtorque
Return the MEASUrement:MEAS<x>:LTORque command.
Description
- This command sets or queries the measurement Low Torque value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LTORque?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LTORque?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LTORque valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LTORque <NR1>
- MEASUrement:MEAS<x>:LTORque?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the Low Torque value of the measurement in the range of 0 to 10000000.
property
¶
ltype: MeasurementMeasItemLtype
Return the MEASUrement:MEAS<x>:LTYPe command.
Description
- This command sets or returns the value for the level type as auto or custom. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LTYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LTYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LTYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LTYPe {AUTO|CUSTom}
- MEASUrement:MEAS<x>:LTYPe?
Info
AUTOspecifies the value for the level type as auto.CUSTomspecifies the value for the level type as custom.
property
¶
lunits: MeasurementMeasItemLunits
Return the MEASUrement:MEAS<x>:LUNITs command.
Description
- This command sets or returns the value for the level units as percentage or absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LUNITs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LUNITs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LUNITs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LUNITs {PERCent|ABSolute}
- MEASUrement:MEAS<x>:LUNITs?
Info
PERCentspecifies the value for the level units as percent.ABSolutespecifies the value for the level units as absolute.
property
¶
lvoltage: MeasurementMeasItemLvoltage
Return the MEASUrement:MEAS<x>:LVOLtage command.
Description
- This command sets or queries the measurement Torque Low Voltage value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LVOLtage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LVOLtage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LVOLtage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LVOLtage <NR1>
- MEASUrement:MEAS<x>:LVOLtage?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the Low Voltage value of the measurement in the range of -100 to 100.
property
¶
maxcurrent: MeasurementMeasItemMaxcurrent
Return the MEASUrement:MEAS<x>:MAXCUrrent command.
Description
- This command sets or returns the maximum current. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXCUrrent?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXCUrrent?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXCUrrent valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXCUrrent <NR3>
- MEASUrement:MEAS<x>:MAXCUrrent?
Info
<NR3>specifies the maximum current.
property
¶
maxcycle: MeasurementMeasItemMaxcycle
Return the MEASUrement:MEAS<x>:MAXCycle command.
Description
- This command sets or queries the maximum cycle value for the DDRTERRN and DDRTERRMN measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXCycle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXCycle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXCycle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXCycle <NR1>
- MEASUrement:MEAS<x>:MAXCycle?
Info
MEAS<x>specifies the measurement number.<NR1>is the maximum cycle range limit value in the range or 2 to 50.
property
¶
maxgvoltage: MeasurementMeasItemMaxgvoltage
Return the MEASUrement:MEAS<x>:MAXGVoltage command.
Description
- This command sets or returns the maximum gate voltage. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXGVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXGVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXGVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXGVoltage <NR3>
- MEASUrement:MEAS<x>:MAXGVoltage?
Info
<NR3>specifies the maximum gate voltage.
property
¶
maxvoltage: MeasurementMeasItemMaxvoltage
Return the MEASUrement:MEAS<x>:MAXVoltage command.
Description
- Sets or queries the maximum input voltage. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXVoltage <NR2>
- MEASUrement:MEAS<x>:MAXVoltage?
Info
<NR2>is the maximum input voltage, in the range of -61 V to +61 V.
property
¶
measrange: MeasurementMeasItemMeasrange
Return the MEASUrement:MEAS<x>:MEASRange command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.global: TheMEASUrement:MEAS<x>:MEASRange:GLOBalcommand..max: TheMEASUrement:MEAS<x>:MEASRange:MAXcommand..min: TheMEASUrement:MEAS<x>:MEASRange:MINcommand..state: TheMEASUrement:MEAS<x>:MEASRange:STATEcommand.
property
¶
mech: MeasurementMeasItemMech
Return the MEASUrement:MEAS<x>:MECH command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.eindexz: TheMEASUrement:MEAS<x>:MECH:EINDexzcommand..gratio: TheMEASUrement:MEAS<x>:MECH:GRATiocommand..munits: TheMEASUrement:MEAS<x>:MECH:MUNitscommand..ppairs: TheMEASUrement:MEAS<x>:MECH:PPAirscommand..pprotation: TheMEASUrement:MEAS<x>:MECH:PPRotationcommand..stype: TheMEASUrement:MEAS<x>:MECH:STYPecommand.
property
¶
mincycle: MeasurementMeasItemMincycle
Return the MEASUrement:MEAS<x>:MINCycle command.
Description
- This command sets or queries the minimum cycle value for the DDRTERRN and DDRTERRMN measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MINCycle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MINCycle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MINCycle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MINCycle <NR1>
- MEASUrement:MEAS<x>:MINCycle?
Info
MEAS<x>specifies the measurement number.<NR1>is the minimum cycle range limit value in the range or 2 to 50.
property
¶
oddeven: MeasurementMeasItemOddeven
Return the MEASUrement:MEAS<x>:ODDEVen command.
Description
- This command sets or queries harmonics oddeven.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:ODDEVen?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:ODDEVen?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:ODDEVen valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:ODDEVen {ALL|EVEN|ODD}
- MEASUrement:MEAS<x>:ODDEVen?
Info
MEAS<x>specifies the measurement number.ALLdisplays all the results.EVENdisplays the even results.ODDdisplays the odd results.
property
¶
ofilters: MeasurementMeasItemOfilters
Return the MEASUrement:MEAS<x>:OFILters command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.lowpass: TheMEASUrement:MEAS<x>:OFILters:LOWPasscommand tree.
property
¶
osangle: MeasurementMeasItemOsangle
Return the MEASUrement:MEAS<x>:OSANgle command.
Description
- This command sets or queries the specified measurement Offset angle.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OSANgle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OSANgle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OSANgle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OSANgle <NR1>
- MEASUrement:MEAS<x>:OSANgle?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the offset angle of the measurement in the range or -360 to 360.
property
¶
outedgequalifier: MeasurementMeasItemOutedgequalifier
Return the MEASUrement:MEAS<x>:OUTEDGEQUALifier command.
Description
- This command sets or queries local output edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTEDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTEDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTEDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTEDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:OUTEDGEQUALifier?
Info
MEAS<x>specifies the measurement number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
outfilters: MeasurementMeasItemOutfilters
Return the MEASUrement:MEAS<x>:OUTFILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.lowpass: TheMEASUrement:MEAS<x>:OUTFILTers:LOWPasscommand tree.
property
¶
outputvoltage: dict[int, MeasurementMeasItemOutputvoltageItem]
Return the MEASUrement:MEAS<x>:OUTPUT<n>VOLTage command.
Description
- Sets or queries the voltage level for the specified output voltage source n.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTPUT<n>VOLTage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTPUT<n>VOLTage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTPUT<n>VOLTage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTPUT<n>VOLTage <NR2>
- MEASUrement:MEAS<x>:OUTPUT<n>VOLTage?
Info
MEAS<x>specifies the measurement number.<NR2>is the output voltage for source n, in the range of -61 V to +61 V.
property
¶
passfailenabled: MeasurementMeasItemPassfailenabled
Return the MEASUrement:MEAS<x>:PASSFAILENabled command.
Description
- This command returns or sets the pass/fail test enable status. If enabled, this will turn on pass fail testing for the specified measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILENabled?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILENabled?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILENabled valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?
Info
<NR1>enables or disables pass fail testing for the specified measurement. A value of 1 enables and a value of 0 disables.
property
¶
passfailhighlimit: MeasurementMeasItemPassfailhighlimit
Return the MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.
Description
- This command returns or sets the high limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILHIGHlimit?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILHIGHlimit?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILHIGHlimit valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?
Info
<NR2>sets the high limit for a measurement test. The high limit is a number which a measurement result will be tested against.
property
¶
passfaillimit: MeasurementMeasItemPassfaillimit
Return the MEASUrement:MEAS<x>:PASSFAILLIMit command.
Description
- This command returns or sets the limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILLIMit?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILLIMit?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILLIMit valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?
Info
<NR2>sets the limit for a measurement test. The limit is a number which a measurement result will be tested against.
property
¶
passfaillowlimit: MeasurementMeasItemPassfaillowlimit
Return the MEASUrement:MEAS<x>:PASSFAILLOWlimit command.
Description
- This command returns or sets the low limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILLOWlimit?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILLOWlimit?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILLOWlimit valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?
Info
<NR2>sets the low limit for a measurement test. The limit is a number which a measurement result will be tested against.
property
¶
passfailmargin: MeasurementMeasItemPassfailmargin
Return the MEASUrement:MEAS<x>:PASSFAILMARgin command.
Description
- This command returns or sets the allowed margin for limit comparisons for all pass/fail checks. This is given as a percentage with a default value of 0.05 representing 5%. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILMARgin?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILMARgin?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILMARgin valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?
Info
<NR2>sets the allowed margin for limit comparisons for all pass/fail checks. The margin as a percentage of the limit.
property
¶
passfailwhen: MeasurementMeasItemPassfailwhen
Return the MEASUrement:MEAS<x>:PASSFAILWHEN command.
Description
- This command sets or returns the condition on which a measurement test fails. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILWHEN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILWHEN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILWHEN valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?
Info
LESSthansets the condition for measurement test failure as less than the given limit. This is the default value.GREATERthansets the condition for measurement test failure as greater than the given limit.Equalssets the condition for measurement test failure as equals the given limit.NOTEQualssets the condition for measurement test failure as not equal to the given limit.INSIDErangesets the condition for measurement test failure as inside the limit range.OUTSIDErangesets the condition for measurement test failure as outside the limit range.
property
¶
patterndetection: MeasurementMeasItemPatterndetection
Return the MEASUrement:MEAS<x>:PATTERNDETECTION command.
Description
- This command sets or queries the pattern detection type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PATTERNDETECTION?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PATTERNDETECTION?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PATTERNDETECTION valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PATTERNDETECTION {AUTO|MANUAL}
- MEASUrement:MEAS<x>:PATTERNDETECTION?
Info
MEAS<x>specifies the measurement number.AUTOautomatically detects the pattern.MANUALrequires manually detecting the pattern.
property
¶
patternlength: MeasurementMeasItemPatternlength
Return the MEASUrement:MEAS<x>:PATTERNLENgth command.
Description
- This command sets or queries the pattern length for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PATTERNLENgth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PATTERNLENgth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PATTERNLENgth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PATTERNLENgth <NR3>
- MEASUrement:MEAS<x>:PATTERNLENgth?
Info
MEAS<x>specifies the measurement number.<NR3>is the pattern length.
property
¶
patterntype: MeasurementMeasItemPatterntype
Return the MEASUrement:MEAS<x>:PATTERNTYPe command.
Description
- This command sets or queries the pattern type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PATTERNTYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PATTERNTYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PATTERNTYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PATTERNTYPe {REPeating|ARBitrary}
- MEASUrement:MEAS<x>:PATTERNTYPe?
Info
MEAS<x>specifies the measurement number.REPeatingspecifies a repeating pattern.ARBitraryspecifies an arbitrary pattern.
property
¶
pcount: MeasurementMeasItemPcount
Return the MEASUrement:MEAS<x>:PCOUNt command.
Description
- This command sets or returns number of pulses. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PCOUNt?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PCOUNt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PCOUNt valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PCOUNt <NR3>
- MEASUrement:MEAS<x>:PCOUNt?
Info
MEAS<x>specifies the measurement number.<NR3>is the number of pulses.
property
¶
perfreq: MeasurementMeasItemPerfreq
Return the MEASUrement:MEAS<x>:PERFREQ command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PERFREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PERFREQ?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.edge: TheMEASUrement:MEAS<x>:PERFREQ:EDGEcommand.
property
¶
polarity: MeasurementMeasItemPolarity
Return the MEASUrement:MEAS<x>:POLarity command.
Description
- This command sets or queries the polarity for the measurement when the measurement type is burst width. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POLarity?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POLarity?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POLarity valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?
Info
MEAS<x>specifies the measurement number.NORMalspecifies normal polarity.INVertedspecifies inverted polarity.
property
¶
population: MeasurementMeasItemPopulation
Return the MEASUrement:MEAS<x>:POPUlation command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.global: TheMEASUrement:MEAS<x>:POPUlation:GLOBalcommand..limit: TheMEASUrement:MEAS<x>:POPUlation:LIMITcommand tree.
property
¶
powerfactor: MeasurementMeasItemPowerfactor
Return the MEASUrement:MEAS<x>:POWERFACtor command.
Description
- This command sets or queries the power factor value for IEC-Class C type harmonics standard. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POWERFACtor?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POWERFACtor?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POWERFACtor valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POWERFACtor <NR2>
- MEASUrement:MEAS<x>:POWERFACtor?
Info
MEAS<x>specifies the measurement number.<NR2>specifies the power factor value for class C harmonics standard.
property
¶
pregion: MeasurementMeasItemPregion
Return the MEASUrement:MEAS<x>:PREGion command.
Description
- This command sets or returns pulse region for a measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PREGion?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PREGion?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PREGion valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PREGion {FPULse|SPULse|MPULse}
- MEASUrement:MEAS<x>:PREGion?
Info
FPULseis the pulse region as Fpulse.SPULseis the pulse region as Spulse.MPULseis the pulse region as Mpulse.
property
¶
pwidth: MeasurementMeasItemPwidth
Return the MEASUrement:MEAS<x>:PWIDth command.
Description
- This command sets or returns pulse width. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PWIDth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PWIDth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PWIDth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PWIDth <NR3>
- MEASUrement:MEAS<x>:PWIDth?
Info
<NR3>specifies the pulse width.
property
¶
redge: MeasurementMeasItemRedge
Return the MEASUrement:MEAS<x>:REDGe command.
Description
- This command turns on or off the Refine edge on qualifier. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REDGe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REDGe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REDGe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REDGe {ON|OFF}
- MEASUrement:MEAS<x>:REDGe?
Info
ONspecifies the Refine edge settings has been turned on.OFFspecifies the Refine edge settings has been turned off.
property
¶
reflevels: MeasurementMeasItemReflevels
Return the MEASUrement:MEAS<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.absolute: TheMEASUrement:MEAS<x>:REFLevels:ABSolutecommand tree.
property
¶
reflevels1: MeasurementMeasItemReflevels1
Return the MEASUrement:MEAS<x>:REFLevels1 command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.absolute: TheMEASUrement:MEAS<x>:REFLevels1:ABSolutecommand tree..basetop: TheMEASUrement:MEAS<x>:REFLevels1:BASETopcommand..method: TheMEASUrement:MEAS<x>:REFLevels1:METHodcommand..percent: TheMEASUrement:MEAS<x>:REFLevels1:PERCentcommand tree.
property
¶
refmode: MeasurementMeasItemRefmode
Return the MEASUrement:MEAS<x>:REFMode command.
Description
- This command sets or queries the reference level mode for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFMode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFMode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFMode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?
Info
MEAS<x>specifies the measurement number.AUTOsets the reference level for the measurement automatically.MANualallows the user to set the reference level for the measurement.
property
¶
refvoltage: MeasurementMeasItemRefvoltage
Return the MEASUrement:MEAS<x>:REFVoltage command.
Description
- This command sets or queries the reference voltage value for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?
Info
MEAS<x>is the measurement number.<NR3>is the reference voltage value for the selected configuration.
property
¶
refvoltageval: dict[int, MeasurementMeasItemRefvoltagevalItem]
Return the MEASUrement:MEAS<x>:REFVOLTAGE<n>Val command.
Description
- Sets or queries the reference voltage per rail of Overshoot and Undershoot measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFVOLTAGE<n>Val?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFVOLTAGE<n>Val?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFVOLTAGE<n>Val valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFVOLTAGE<n>Val <NR2>
- MEASUrement:MEAS<x>:REFVOLTAGE<n>Val?
Info
MEAS<x>is the measurement number.<n>is the rail number.<NR2>is the reference voltage, in the range of -500 V to +500 V.
property
¶
results: MeasurementMeasItemResults
Return the MEASUrement:MEAS<x>:RESUlts command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.allacqs: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqscommand tree..currentacq: TheMEASUrement:MEAS<x>:RESUlts:CURRentacqcommand tree..history: TheMEASUrement:MEAS<x>:RESUlts:HISTorycommand tree.
property
¶
ripplefreqval: dict[int, MeasurementMeasItemRipplefreqvalItem]
Return the MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val command.
Description
- Sets or queries the ripple frequency per specified rail for Ripple measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RIPPLEFREQ<n>Val?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RIPPLEFREQ<n>Val?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:RIPPLEFREQ<n>Val valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val <NR3>
- MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val?
Info
MEAS<x>is the measurement number.<n>is the rail number.<NR3>is the frequency, in the range of 1 Hz to 4 GHz.
property
¶
sequence: MeasurementMeasItemSequence
Return the MEASUrement:MEAS<x>:SEQuence command.
Description
- This command sets or queries the sequence of hall edges. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SEQuence?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SEQuence?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SEQuence valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SEQuence {ABC|ACB}
- MEASUrement:MEAS<x>:SEQuence?
Info
MEAS<x>specifies the measurement number.ABCspecifies the motor Hall edges sequence as ABC.ACBspecifies the motor Hall edges sequence as ACB.
property
¶
signalfrequency: MeasurementMeasItemSignalfrequency
Return the MEASUrement:MEAS<x>:SIGNALFREQUEncy command.
Description
- This command sets or queries line frequency for Harmonics and Ripple line frequency. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SIGNALFREQUEncy?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SIGNALFREQUEncy?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SIGNALFREQUEncy valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SIGNALFREQUEncy {AUTO|FIFTYHZ|SIXTYHZ|FOURHUNDREDHZ|CUSTOM}
- MEASUrement:MEAS<x>:SIGNALFREQUEncy?
Info
MEAS<x>specifies the measurement number.AUTOspecifies the line frequency as auto. Only available for Harmonics line frequency.FIFTYHZspecifies the line frequency as 50 Hz.SIXTYHZspecifies the line frequency as 60 Hz.FOURHUNDREDHZspecifies the line frequency as 400 Hz. .CUSTOMspecifies the line frequency as custom.
property
¶
signaltype: MeasurementMeasItemSignaltype
Return the MEASUrement:MEAS<x>:SIGNALType command.
Description
- This command sets or queries the signal type of source 1 for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SIGNALType?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SIGNALType?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SIGNALType valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?
Info
MEAS<x>specifies the measurement number.CLOCKspecifies a clock signal type.DATAspecifies a data signal type.AUTOautomatically selects the signal type.
property
¶
slabs: MeasurementMeasItemSlabs
Return the MEASUrement:MEAS<x>:SLABs command.
Description
- This command sets or returns the value for the start level in absolute.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SLABs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SLABs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SLABs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SLABs <NR3>
- MEASUrement:MEAS<x>:SLABs?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the start level in absolute.
property
¶
slpct: MeasurementMeasItemSlpct
Return the MEASUrement:MEAS<x>:SLPCt command.
Description
- This command sets or returns the value for the start level in percentage.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SLPCt?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SLPCt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SLPCt valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SLPCt <NR3>
- MEASUrement:MEAS<x>:SLPCt?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the start level in percentage.
property
¶
sltype: MeasurementMeasItemSltype
Return the MEASUrement:MEAS<x>:SLTYpe command.
Description
- This command sets or returns the start level source type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SLTYpe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SLTYpe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SLTYpe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:SLTYpe?
Info
MEAS<x>specifies the measurement number.VDSspecifies the start level source type as VDS.IDspecifies the start level source type as ID.VGEspecifies the start level source type as VGE.VCEspecifies the start level source type as VCE.ICspecifies the start level source type as IC.
property
¶
smoothingfilter: MeasurementMeasItemSmoothingfilter
Return the MEASUrement:MEAS<x>:SMOOTHINGFILTER command.
Description
- This command sets or queries the status of smoothing filter.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:SMOOTHINGFILTER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SMOOTHINGFILTER <NR1>
Info
MEAS<x>specifies the measurement number.<NR1>sets the value to 1 or 0. 1 enables smoothing filter and 0 disables it.
property
¶
source: MeasurementMeasItemSource
Return the MEASUrement:MEAS<x>:SOURCE command.
Description
- This command sets or queries local input source.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SOURCE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SOURCE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SOURCE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOURCE?
Info
MEAS<x>specifies the measurement number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
source1: MeasurementMeasItemSource1
Return the MEASUrement:MEAS<x>:SOUrce1 command.
Description
- This command sets or queries the measurement source. The measurement number and source are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SOUrce1?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SOUrce1?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SOUrce1 valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SOUrce1 {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOUrce1?
Info
MEAS<x>specifies the measurement number.1specifies the source number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
Return the MEASUrement:MEAS<x>:SSC command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SSC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SSC?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.nominalfreq: TheMEASUrement:MEAS<x>:SSC:NOMinalfreqcommand.
property
¶
status: MeasurementMeasItemStatus
Return the MEASUrement:MEAS<x>:STATUS command.
Description
- This command returns the pass fail status, if applicable, for the selected measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STATUS?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STATUS?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:STATUS?
Info
PASSspecifies that the user specified measurement limit has not been violated.FAILspecifies that the user specified measurement limit has been violated.
property
¶
stlabs: MeasurementMeasItemStlabs
Return the MEASUrement:MEAS<x>:STLABs command.
Description
- This command sets or returns the value for the stop level in absolute.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STLABs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STLABs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STLABs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STLABs <NR3>
- MEASUrement:MEAS<x>:STLABs?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the stop level in absolute.
property
¶
stlpct: MeasurementMeasItemStlpct
Return the MEASUrement:MEAS<x>:STLPct command.
Description
- This command sets or returns the value for the stop level in percentage.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STLPct?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STLPct?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STLPct valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STLPct <NR3>
- MEASUrement:MEAS<x>:STLPct?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the stop level in percentage.
property
¶
stltype: MeasurementMeasItemStltype
Return the MEASUrement:MEAS<x>:STLTYpe command.
Description
- This command sets or returns the stop level source type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STLTYpe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STLTYpe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STLTYpe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:STLTYpe?
Info
MEAS<x>specifies the measurement number.VDSspecifies the stop level source type as VDS.IDspecifies the stop level source type as ID.VGEspecifies the stop level source type as VGE.VCEspecifies the stop level source type as VCE.ICspecifies the stop level source type as IC.
property
¶
stype: MeasurementMeasItemStype
Return the MEASUrement:MEAS<x>:STYPe command.
Description
- This command sets or queries the source type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STYPe {VOLTage|CURRent}
- MEASUrement:MEAS<x>:STYPe?
Info
MEAS<x>specifies the measurement number.VOLTagesets source type as Voltage.CURRentsets source type as Current.
property
¶
sunits: MeasurementMeasItemSunits
Return the MEASUrement:MEAS<x>:SUNits command.
Description
- This command sets or queries the speed units for the specific measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SUNits?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SUNits valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SUNits {RPM|HZ}
- MEASUrement:MEAS<x>:SUNits?
Info
MEAS<x>specifies the measurement number.RPMdefines the speed measurement units as RPM.HZdefines the speed measurement units as HZ.
property
¶
tckavg: MeasurementMeasItemTckavg
Return the MEASUrement:MEAS<x>:TCKAVG command.
Description
- This command sets or queries the average clock period value used in DDR measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TCKAVG?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TCKAVG?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TCKAVG valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TCKAVG <NR3>
- MEASUrement:MEAS<x>:TCKAVG?
Info
MEAS<x>specifies the measurement number.NR3is a floating point number that represents the DDR average clock period in seconds.
property
¶
tconstant: MeasurementMeasItemTconstant
Return the MEASUrement:MEAS<x>:TCONstant command.
Description
- This command sets or queries the measurement Torque Constant.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TCONstant?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TCONstant?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TCONstant valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TCONstant <NR1>
- MEASUrement:MEAS<x>:TCONstant?
Info
MEAS<x>specifies the measurement number.NR1specifies the current multiplier value of the measurement in the range of 0 to 100.
property
¶
timingmode: MeasurementMeasItemTimingmode
Return the MEASUrement:MEAS<x>:TIMINGMode command.
Description
- This command sets or queries the Timing mode for the specified DDR measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TIMINGMode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TIMINGMode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TIMINGMode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TIMINGMode {EACHCLOCKCYCLE|TWOCLOCKCYCLES}
- MEASUrement:MEAS<x>:TIMINGMode?
Info
MEAS<x>specifies the measurement number.EACHCLOCKCYCLEsets the DDR Timing Mode to use each clock cycle at a time.TWOCLOCKCYCLESsets the DDR Timing Mode to use two cycles at a time.
property
¶
tmethod: MeasurementMeasItemTmethod
Return the MEASUrement:MEAS<x>:TMEThod command.
Description
- This command sets or queries the measurement torque method.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TMEThod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TMEThod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TMEThod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TMEThod {SENSOR|CURRENT}
- MEASUrement:MEAS<x>:TMEThod?
Info
MEAS<x>specifies the measurement number.SENSORspecifies the Torque Method as SENSOR.CURRENTspecifies the Torque Method as CURRENT.
property
¶
toedge: MeasurementMeasItemToedge
Return the MEASUrement:MEAS<x>:TOEdge command.
Description
- This command sets or queries the ‘to edge’ type for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOEdge?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOEdge?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOEdge valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?
Info
MEAS<x>specifies the measurement number.FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both a rising and falling edge of the waveform.SAMEasspecifies that both edges of the waveform are the same.OPPositeasspecifies that the edges of the waveform are not the same.
property
¶
toedgesearchdirect: MeasurementMeasItemToedgesearchdirect
Return the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.
Description
- This command sets or queries the to edge search direction for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOEDGESEARCHDIRect?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOEDGESEARCHDIRect?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOEDGESEARCHDIRect valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?
Info
MEAS<x>specifies the measurement number.FORWardspecifies a forward search to the edge.BACKWardspecifies a backward search to the edge.
property
¶
tosymbol: MeasurementMeasItemTosymbol
Return the MEASUrement:MEAS<x>:TOSYmbol command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.logic2source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrcecommand..logic3source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrcecommand..logic4source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrcecommand..logic5source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrcecommand..measureat: TheMEASUrement:MEAS<x>:TOSYmbol:MEASUREATcommand.
property
¶
transition: MeasurementMeasItemTransition
Return the MEASUrement:MEAS<x>:TRANSition command.
Description
- This command sets or queries the transition edges flag for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:TRANSition valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}
Info
<NR1>= 1, the measurement is computed on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only. If it is set to 0, the measurement is computed on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.OFFcomputes the measurement on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.ONcomputes the measurement on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only.
property
¶
type: MeasurementMeasItemType
Return the MEASUrement:MEAS<x>:TYPe command.
Description
- This command sets or queries the measurement type for the measurement specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TYPe {ACCOMMONMODE|ACRMS|AMPlITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMOVERSHOOT|DPMUNDERSHOOT|DPMRIPPLE|DPMTURNOFFTIME|DPMTURNONTIME|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HIGH|HEIGHT|HEIGHTBER|HIGHTIME|HOLD|IMDAPOWERQUALITY|IMDAHARMONICS|IMDAINPUTVOLTAGE|IMDAINPUTCURRENT|IMDAINPUTPOWER|IMDAPHASORDIAGRAM|IMDAEFFICIENCY|IMDALINERIPPLE|IMDASWITCHRIPPLE|IMDADQ0|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NPJ|NOVERSHOOT|NWIDTH|PDUTTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SRJ|SSCFREQDEV|SSCMODRATE|SETUP|SKEW|TIE|TIMEOUTSIDELEVEL|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WIDTH|WIDTHBER}
- MEASUrement:MEAS<x>:TYPe?
Info
ACCOMMONMODEAC Common Mode (Pk-Pk) is the peak-to-peak of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.ACRMS(AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.AMPLITUDEis the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.Amplitude = High - LowAREAis the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.BASEis the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.BITAMPLITUDE(Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITHIGH(Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITLOW(Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BURSTWIDTH(Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.COMMONMODE(DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DATARATE(Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.DCD(duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDJ(data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDRAOS(area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.DDRAOSPERTCK(area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAOSPERUI(area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRAUS(area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.DDRAUSPERTCK(area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAUSPERUI(area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRHOLDDIFF(hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.DDRSETUPDIFF(setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.DDRTCHABS(absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.DDRTCHAVERAGE(average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles.This measurement is made across the entire record.DDRTCKAVERAGE(average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles.This measurement is made across the entire record.DDRTCLABS(absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.DDRTCLAVERAGE(average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.DDRTERRMN(cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).DDRTERRN(cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).DDRTJITCC(cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.DDRTJITDUTY(half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.DDRTJITPER(clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.DDRTPST(read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.DDRTRPRE(read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRTWPREis the width of the Write burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRVIXACis the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.DDRTDQSCKis the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.DELayis the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.DJ(deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DJDIRAC(dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DPMOVERSHOOTis the difference between Maximum and Top, divided by the amplitude. This measurement can be made across the entire record or on each cycle in the record at the specified reference voltage.DPMUNDERSHOOTis the difference between Minimum and Base, divided by the amplitude. This measurement can be made across the entire record or on each cycle in the record at the specified reference voltage.DPMRIPPLEis the RMS and peak-to-peak values of the output signal on the DC Rail.DPMTURNOFFTIMEis the time delay between load current going low to other rail outputs going low during power down.DPMTURNONTIMEis the time delay between load current going high to other rail outputs going high during power on.EYEHIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.EYELOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.FALLSLEWRATE(Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.FALLTIME(Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.FREQuencyis the reciprocal of Period. This measurement is made on each cycle in the record.F2is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F4is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F8is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.HEIGHT(Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HEIGHTBER(Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGHTIME(High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.HOLD(Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.IMDAPOWERQUALITY(Power Quality) measures the Frequency and RMS values of the voltage and current, Crest Factors of the voltage and current, True Power (PTRUE), Reactive Power (PRE), Apparent Power (PAPP), Power Factor, and Phase Angle (θ) of the AC signal.IMDAHARMONICS(Harmonics) plots the signal amplitude at the fundamental line frequency and its harmonics and measures the RMS amplitude and Total Harmonic Distortion of the signal.IMDAINPUTVOLTAGE(Input Voltage) measures the RMS value of the Input Voltages. The number of voltages can vary with wiring configuration.IMDAINPUTCURRENT(Input Current) measures the RMS value of the Input Currents. The number of currents can vary with wiring configuration.IMDAINPUTPOWER(Input Power) measures the RMS value of the Input Power. The power waveforms are shown as derived MATH waveforms, which are respective pairs of Input Voltage \* Current waveforms.IMDAPHASORDIAGRAM(Phasor Diagram) represents magnitudes and phase angles between voltage(s) and current(s) per winding pair.IMDAEFFICIENCY(Efficiency) measures the ratio of sum of output power(s) to input power for respective input and output Voltage and Current pairs. Note: the current release cannot support 3V and 3I pairs, since this requires 12 channels. We restrict to 2V and 2I which needs 8 scope channels.IMDALINERIPPLE(Line Ripple) provides the RMS and peak-to-peak measurements of the line frequency portion of the respective AC Voltage or Current signals.IMDASWITCHINGRIPPLE(Switching Ripple) provides the RMS and peak-to-peak measurements of the respective Voltage or Current signals.IMDADQ0measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0.JITTERSUMMARY(Jitter Summary) is a group consisting of the following measurements: TIE, TJ@BER, Eye Width@BER, Eye Height@BER, RJ-δδ, DJ-δδ, PJ, DDJ, DcD, F/2, F/4, F/8. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J2is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J9is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.LOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.LOWTIME(Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.MAXimumis the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.MEANis the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.MINImumis the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.NDUty(Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.Negative Duty Cycle = (Negative Width) / Period × 100%NPERIOD(Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.NPJ(non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.NOVershoot(Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Negative Overshoot = (Base - Minimum) / Amplitude × 100%)NWIdth(Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.PDUTY(Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.Positive Duty Cycle = (Positive Width)/Period × 100%PERIODis the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.PHASEis the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.PHASENOISE(Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.PJ(periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.PK2Pk(Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.POVERSHOOT(Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Positive Overshoot = (Maximum - Top) / Amplitude ×100%PWIDTH(Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.QFACTOR(Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RISESLEWRATE(Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RISETIMERise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RJ(random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RJDIRAC(dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RMSis the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.SRJ(sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCFREQDEV(SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCMODRATE(SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SETUP(Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.SKEWSkew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.TIE(time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.TIMEOUTSIDELEVELTime Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.TJBER(total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TNTRATIOT/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TOPis the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.UNITINTERVAL(Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.VDIFFXOVR(Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTH(Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTHBER(Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
property
¶
waittime: MeasurementMeasItemWaittime
Return the MEASUrement:MEAS<x>:WAITTime command.
Description
- Sets or queries the wait time.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:WAITTime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:WAITTime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:WAITTime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:WAITTime <NR2>
- MEASUrement:MEAS<x>:WAITTime?
Info
MEAS<x>is the measurement number.<NR2>is the wait time, in the range of 1 s to 500 s.
property
¶
windowlength: MeasurementMeasItemWindowlength
Return the MEASUrement:MEAS<x>:WINDOWLENgth command.
Description
- This command sets or queries the window length for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:WINDOWLENgth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:WINDOWLENgth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:WINDOWLENgth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:WINDOWLENgth <NR3>
- MEASUrement:MEAS<x>:WINDOWLENgth?
Info
<NR3>is the value for the window length.
property
¶
xunit: MeasurementMeasItemXunit
Return the MEASUrement:MEAS<x>:XUNIT command.
Description
- Returns the horizontal scale units of the specified measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:XUNIT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:XUNIT?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:XUNIT?
Info
MEAS<x>specifies the measurement number.
property
¶
yunit: MeasurementMeasItemYunit
Return the MEASUrement:MEAS<x>:YUNIT command.
Description
- Returns the vertical scale units of the specified measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:YUNIT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:YUNIT?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:YUNIT?
Info
MEAS<x>specifies the measurement number.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BER command.
Description
- This command sets or queries BER value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BER <NR3>
- MEASUrement:MEAS<x>:BER?
Info
MEAS<x>specifies the measurement number.<NR3>is BER value for the measurement.
Properties
.targetber: TheMEASUrement:MEAS<x>:BER:TARGETBERcommand.
property
¶
targetber: MeasurementMeasItemBerTargetber
Return the MEASUrement:MEAS<x>:BER:TARGETBER command.
Description
- This command sets or queries the target BER value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BER:TARGETBER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BER:TARGETBER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BER:TARGETBER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BER:TARGETBER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER?
Info
MEAS<x>specifies the measurement number.<NR3>is the target BER value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BER:TARGETBER command.
Description
- This command sets or queries the target BER value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BER:TARGETBER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BER:TARGETBER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BER:TARGETBER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BER:TARGETBER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER?
Info
MEAS<x>specifies the measurement number.<NR3>is the target BER value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BIN command.
Description
- This command sets or queries the bin count for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BIN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BIN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BIN valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BIN <NR3>
- MEASUrement:MEAS<x>:BIN?
Info
MEAS<x>specifies the measurement number.<NR3>is the bin count.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BITCfgmode command.
Description
- This command sets or queries whether the measurement returns the mean or mode statistic result when the measurement type is bit amplitude/high/low. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITCfgmode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITCfgmode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITCfgmode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITCfgmode {MEAN|MODE}
- MEASUrement:MEAS<x>:BITCfgmode?
Info
MEAS<x>specifies the measurement number.MEANspecifies that the measurement returns results for each bit.MODEspecifies that the measurement returns the mode of its results.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BITEnd command.
Description
- This command sets or queries the bit end as a percentage of the unit interval. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITEnd?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITEnd?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITEnd valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITEnd <NR3>
- MEASUrement:MEAS<x>:BITEnd?
Info
MEAS<x>specifies the measurement number.<NR3>is the bit end.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BITPcnt command.
Description
- This command sets or queries the bit center as a percentage of the unit interval. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITPcnt?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITPcnt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITPcnt valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITPcnt <NR3>
- MEASUrement:MEAS<x>:BITPcnt?
Info
MEAS<x>specifies the measurement number.<NR3>is the bit center percentage value to be measured for the bit type selected.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BITSTart command.
Description
- This command sets or queries the bit start as a percentage of the unit interval. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITSTart?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITSTart?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITSTart valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITSTart <NR3>
- MEASUrement:MEAS<x>:BITSTart?
Info
MEAS<x>specifies the measurement number.<NR3>is the bit start.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BITType command.
Description
- This command sets or queries the bit type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BITType?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BITType?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BITType valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- MEASUrement:MEAS<x>:BITType?
Info
MEAS<x>specifies the measurement number.ALLBitsspecifies that the measurement returns results for all bits.TRANSitionspecifies that the measurement returns results for transitions bit only.NONTRANsitionspecifies that the measurement returns results for non-transition bits only.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:BURSTEDGTYPe command.
Description
- This command sets or queries the burst edge type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:BURSTEDGTYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:BURSTEDGTYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:BURSTEDGTYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?
Info
MEAS<x>specifies the measurement number.RISEspecifies a burst with a rising edge.FALLspecifies a burst with a falling edge.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.allacqs: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqscommand tree..currentacq: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacqcommand tree.
property
¶
allacqs: MeasurementMeasItemCcresultsAllacqs
Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.maximum: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEANcommand..minimum: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PKcommand..population: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDevcommand.
property
¶
currentacq: MeasurementMeasItemCcresultsCurrentacq
Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.maximum: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEANcommand..minimum: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PKcommand..population: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDevcommand.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.maximum: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEANcommand..minimum: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PKcommand..population: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDevcommand.
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.
Description
- This query-only command returns the maximum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.
Description
- This query-only command returns the mean cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.
Description
- This query-only command returns the minimum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.
Description
- This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?
property
¶
population: MeasurementMeasItemCcresultsAllacqsPopulation
Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.
Description
- This query-only command returns the population of all cycle-cycle statistics for the specified measurement for all acquisitions accumulated since statistics were last reset. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.
Description
- This query-only command returns the standard deviation cycle-cycle for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.
Description
- This query-only command returns the maximum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.
Description
- This query-only command returns the mean cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.
Description
- This query-only command returns the minimum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.
Description
- This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.
Description
- This query-only command returns the population of all cycle-cycle statistics for the specified measurement for all acquisitions accumulated since statistics were last reset. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.
Description
- This query-only command returns the standard deviation cycle-cycle for the specified measurement for all acquisitions. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.maximum: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEANcommand..minimum: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PKcommand..population: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDevcommand.
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.
Description
- This query-only command returns the maximum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.
Description
- This query-only command returns the mean cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.
Description
- This query-only command returns the minimum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.
Description
- This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?
property
¶
population: MeasurementMeasItemCcresultsCurrentacqPopulation
Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.
Description
- This query-only command returns the population of the cycle-cycle statistics for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?
property
¶
Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.
Description
- This query-only command returns the standard deviation cycle-cycle for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.
Description
- This query-only command returns the maximum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.
Description
- This query-only command returns the mean cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.
Description
- This query-only command returns the minimum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.
Description
- This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.
Description
- This query-only command returns the population of the cycle-cycle statistics for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.
Description
- This query-only command returns the standard deviation cycle-cycle for the specified measurement for the current acquisition. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.advanced: TheMEASUrement:MEAS<x>:CLOCKRecovery:ADVancedcommand tree..clockfrequency: TheMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequencycommand..clockmultiplier: TheMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultipliercommand..constclockmode: TheMEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODecommand..damping: TheMEASUrement:MEAS<x>:CLOCKRecovery:DAMPingcommand..datapath: TheMEASUrement:MEAS<x>:CLOCKRecovery:DATAPathcommand..datarate: TheMEASUrement:MEAS<x>:CLOCKRecovery:DATARatecommand..explicitclockmode: TheMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODecommand..global: TheMEASUrement:MEAS<x>:CLOCKRecovery:GLOBalcommand..jtfbandwidth: TheMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidthcommand..loopbandwidth: TheMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidthcommand..meanautocalculate: TheMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculatecommand..method: TheMEASUrement:MEAS<x>:CLOCKRecovery:METHodcommand..model: TheMEASUrement:MEAS<x>:CLOCKRecovery:MODelcommand..nominaloffset: TheMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFsetcommand..standard: TheMEASUrement:MEAS<x>:CLOCKRecovery:STAndardcommand.
property
¶
advanced: MeasurementMeasItemClockrecoveryAdvanced
Return the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.method: TheMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHodcommand.
property
¶
clockfrequency: MeasurementMeasItemClockrecoveryClockfrequency
Return the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.
Description
- This command sets or queries the clock frequency used when fixed constant clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock frequency.
property
¶
clockmultiplier: MeasurementMeasItemClockrecoveryClockmultiplier
Return the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.
Description
- This command sets or queries the clock multiplier used when explicit clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock multiplier.
property
¶
constclockmode: MeasurementMeasItemClockrecoveryConstclockmode
Return the MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe command.
Description
- This command sets or queries the constant clock mode used when constant clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
Info
MEAS<x>specifies the measurement number.MEANspecifies that clock recovery uses the mean of the clock signal as the clock frequency.MEDianspecifies that clock recovery uses the mode of the clock signal as the clock frequency.FIXedspecifies that clock recovery uses the value set by the user as the clock frequency.
property
¶
Return the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing command.
Description
- This command sets or queries the damping value used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DAMPing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock recovery damping value.
property
¶
datapath: MeasurementMeasItemClockrecoveryDatapath
Return the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath command.
Description
- This command sets or queries the file containing the data pattern used when known data pattern clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATAPath valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath <QString>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?
Info
MEAS<x>specifies the measurement number.<QString>is the file containing the data pattern to be used for known data pattern clock recovery.
property
¶
datarate: MeasurementMeasItemClockrecoveryDatarate
Return the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate command.
Description
- This command sets or queries the nominal data bit rate when nominal data rate clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATARate?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATARate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATARate valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate?
Info
MEAS<x>specifies the measurement number.<NR3>is the value for the Nominal data rate.
property
¶
explicitclockmode: MeasurementMeasItemClockrecoveryExplicitclockmode
Return the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe command.
Description
- This command sets or queries the explicit clock mode used when explicit clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?
Info
MEAS<x>specifies the measurement number.EDGEspecifies the clock edge.PLLspecifies the phase locked loop.
property
¶
Return the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal command.
Description
- This command sets or queries the clock recovery settings global flag for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFclock recovery settings are changed independently for each individual measurement.ONapplies global clock recovery settings to all the measurements’ clock recovery settings.0clock recovery settings are changed independently for each individual measurement.1applies global clock recovery settings to all the measurements’ clock recovery settings.
property
¶
jtfbandwidth: MeasurementMeasItemClockrecoveryJtfbandwidth
Return the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth command.
Description
- This command sets or queries the JTF bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock recovery JTF bandwidth.
property
¶
loopbandwidth: MeasurementMeasItemClockrecoveryLoopbandwidth
Return the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.
Description
- This command sets or queries the loop bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock recovery loop bandwidth.
property
¶
meanautocalculate: MeasurementMeasItemClockrecoveryMeanautocalculate
Return the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.
Description
- This command sets or queries how often the clock is calculated when constant clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?
Info
MEAS<x>specifies the measurement number.FIRSTcalculates the clock on the first acquisition.EVERYcalculates the clock on every acquisition.
property
¶
Return the MEASUrement:MEAS<x>:CLOCKRecovery:METHod command.
Description
- This command sets or queries the clock recovery method for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:METHod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod?
Info
MEAS<x>specifies the measurement number.PLLspecifies a phase locked loop clock recovery method.CONSTANTCLOCKspecifies using a constant clock.EXPLICITCLOCKspecifies using an explicit clock.
property
¶
Return the MEASUrement:MEAS<x>:CLOCKRecovery:MODel command.
Description
- This command sets or queries the PLL clock recovery model used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MODel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MODel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MODel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel {TYPE<x>}
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel?
Info
MEAS<x>specifies the measurement number.
property
¶
nominaloffset: MeasurementMeasItemClockrecoveryNominaloffset
Return the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.
Description
- This command sets or queries the offset value used when explicit clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock offset.
Sub-properties
.selectiontype: TheMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtypecommand.
property
¶
standard: MeasurementMeasItemClockrecoveryStandard
Return the MEASUrement:MEAS<x>:CLOCKRecovery:STAndard command.
Description
- This command sets or queries the communications standard when PLL clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:STAndard valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
Info
MEAS<x>specifies the measurement number.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.method: TheMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHodcommand.
property
¶
Return the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod command.
Description
- This command sets or queries the advanced clock recovery method when advanced clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?
Info
MEAS<x>specifies the measurement number.NOMinalsets the advanced CRD method to Nominal Data Rate.PATTernsets the advanced CDR method to use a Known Data Pattern.NONEsets no advanced CRD method.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod command.
Description
- This command sets or queries the advanced clock recovery method when advanced clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?
Info
MEAS<x>specifies the measurement number.NOMinalsets the advanced CRD method to Nominal Data Rate.PATTernsets the advanced CDR method to use a Known Data Pattern.NONEsets no advanced CRD method.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.
Description
- This command sets or queries the clock frequency used when fixed constant clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock frequency.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.
Description
- This command sets or queries the clock multiplier used when explicit clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock multiplier.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe command.
Description
- This command sets or queries the constant clock mode used when constant clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
Info
MEAS<x>specifies the measurement number.MEANspecifies that clock recovery uses the mean of the clock signal as the clock frequency.MEDianspecifies that clock recovery uses the mode of the clock signal as the clock frequency.FIXedspecifies that clock recovery uses the value set by the user as the clock frequency.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing command.
Description
- This command sets or queries the damping value used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DAMPing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock recovery damping value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath command.
Description
- This command sets or queries the file containing the data pattern used when known data pattern clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATAPath valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath <QString>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?
Info
MEAS<x>specifies the measurement number.<QString>is the file containing the data pattern to be used for known data pattern clock recovery.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:DATARate command.
Description
- This command sets or queries the nominal data bit rate when nominal data rate clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATARate?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATARate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:DATARate valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate?
Info
MEAS<x>specifies the measurement number.<NR3>is the value for the Nominal data rate.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe command.
Description
- This command sets or queries the explicit clock mode used when explicit clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?
Info
MEAS<x>specifies the measurement number.EDGEspecifies the clock edge.PLLspecifies the phase locked loop.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal command.
Description
- This command sets or queries the clock recovery settings global flag for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFclock recovery settings are changed independently for each individual measurement.ONapplies global clock recovery settings to all the measurements’ clock recovery settings.0clock recovery settings are changed independently for each individual measurement.1applies global clock recovery settings to all the measurements’ clock recovery settings.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth command.
Description
- This command sets or queries the JTF bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock recovery JTF bandwidth.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.
Description
- This command sets or queries the loop bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock recovery loop bandwidth.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.
Description
- This command sets or queries how often the clock is calculated when constant clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?
Info
MEAS<x>specifies the measurement number.FIRSTcalculates the clock on the first acquisition.EVERYcalculates the clock on every acquisition.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:METHod command.
Description
- This command sets or queries the clock recovery method for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:METHod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod?
Info
MEAS<x>specifies the measurement number.PLLspecifies a phase locked loop clock recovery method.CONSTANTCLOCKspecifies using a constant clock.EXPLICITCLOCKspecifies using an explicit clock.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:MODel command.
Description
- This command sets or queries the PLL clock recovery model used when PLL clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MODel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MODel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:MODel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel {TYPE<x>}
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel?
Info
MEAS<x>specifies the measurement number.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.
Description
- This command sets or queries the offset value used when explicit clock recovery is used for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?
Info
MEAS<x>specifies the measurement number.<NR3>is the clock offset.
Properties
.selectiontype: TheMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtypecommand.
property
¶
selectiontype: MeasurementMeasItemClockrecoveryNominaloffsetSelectiontype
Return the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.
Description
- This command sets or queries the offset type used when explicit clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
Info
MEAS<x>specifies the measurement number.AUTOautomatically calculates the offset.MANUALallows the user to set the offset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.
Description
- This command sets or queries the offset type used when explicit clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
Info
MEAS<x>specifies the measurement number.AUTOautomatically calculates the offset.MANUALallows the user to set the offset.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:CLOCKRecovery:STAndard command.
Description
- This command sets or queries the communications standard when PLL clock recovery is used for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:CLOCKRecovery:STAndard valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
Info
MEAS<x>specifies the measurement number.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:COMMONMode command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.filters: TheMEASUrement:MEAS<x>:COMMONMode:FILTerscommand tree..sources: TheMEASUrement:MEAS<x>:COMMONMode:SOURCEscommand.
property
¶
filters: MeasurementMeasItemCommonmodeFilters
Return the MEASUrement:MEAS<x>:COMMONMode:FILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.state: TheMEASUrement:MEAS<x>:COMMONMode:FILTers:STATEcommand.
property
¶
sources: MeasurementMeasItemCommonmodeSources
Return the MEASUrement:MEAS<x>:COMMONMode:SOURCEs command.
Description
- This command sets or queries the number of sources for the measurement when the measurement type is AC common mode. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode:SOURCEs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode:SOURCEs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:COMMONMode:SOURCEs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs {SINGLE|DOUBLE}
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs?
Info
MEAS<x>specifies the measurement number.SINGLEspecifies a single source.DOUBLEspecifies double sources.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:COMMONMode:FILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.state: TheMEASUrement:MEAS<x>:COMMONMode:FILTers:STATEcommand.
property
¶
Return the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE command.
Description
- This command sets or queries whether a filter is used for the measurement when the measurement type is AC common mode. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?
Info
MEAS<x>specifies the measurement number.OFFturns the filter off.ONturns the filter on.0turns the filter off.1turns the filter on.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE command.
Description
- This command sets or queries whether a filter is used for the measurement when the measurement type is AC common mode. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:COMMONMode:FILTers:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?
Info
MEAS<x>specifies the measurement number.OFFturns the filter off.ONturns the filter on.0turns the filter off.1turns the filter on.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:COMMONMode:SOURCEs command.
Description
- This command sets or queries the number of sources for the measurement when the measurement type is AC common mode. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COMMONMode:SOURCEs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COMMONMode:SOURCEs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:COMMONMode:SOURCEs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs {SINGLE|DOUBLE}
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs?
Info
MEAS<x>specifies the measurement number.SINGLEspecifies a single source.DOUBLEspecifies double sources.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:COVer command.
Description
- This command sets or queries the Calculate Over for the Power Quality measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:COVer?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:COVer?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:COVer valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:COVer {FFREQuency|AFREQuencies}
- MEASUrement:MEAS<x>:COVer?
Info
FFREQuencysets Calculate Power Quality measurement.AFREQuenciessets Calculate Power Quality measurement for all frequencies.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CUSTOMLIMITSFile command.
Description
- This command sets or queries the custom limits file path for custom harmonics standard. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CUSTOMLIMITSFile?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CUSTOMLIMITSFile?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CUSTOMLIMITSFile valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile <Qstring>
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile?
Info
MEAS<x>specifies the measurement number.<Qstring>specifies the location of limits file.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:CYCLemode command.
Description
- This command sets or queries the cycle mode for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:CYCLemode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:CYCLemode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:CYCLemode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:CYCLemode {RECORD|CYCLE}
- MEASUrement:MEAS<x>:CYCLemode?
Info
MEAS<x>specifies the measurement number.RECORDspecifies that the measurement is taken over the whole record.CYCLEspecifies that measurements are taken on each cycle of the source.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:DELay command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DELay?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DELay?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.edge: TheMEASUrement:MEAS<x>:DELay:EDGE<x>command.
property
¶
edge: dict[int, MeasurementMeasItemDelayEdgeItem]
Return the MEASUrement:MEAS<x>:DELay:EDGE<x> command.
Description
- This command sets or queries the ‘to edge’ type when EDGE
is EDGE1 and the ‘from edge’ type when EDGE is EDG2, for the measurement when the measurement type is DELAY. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DELay:EDGE<x>?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DELay:EDGE<x>?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:DELay:EDGE<x> valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?
Info
MEAS<x>specifies the measurement number.FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both a rising and falling edge of the waveform.SAMEasspecifies that both edges of the waveform are the same.OPPositeasspecifies that the edges of the waveform are not the same.
Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:DELay:EDGE<x> command.
Description
- This command sets or queries the ‘to edge’ type when EDGE
is EDGE1 and the ‘from edge’ type when EDGE is EDG2, for the measurement when the measurement type is DELAY. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DELay:EDGE<x>?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DELay:EDGE<x>?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:DELay:EDGE<x> valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?
Info
MEAS<x>specifies the measurement number.FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both a rising and falling edge of the waveform.SAMEasspecifies that both edges of the waveform are the same.OPPositeasspecifies that the edges of the waveform are not the same.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:DISPlaystat command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DISPlaystat?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DISPlaystat?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.enable: TheMEASUrement:MEAS<x>:DISPlaystat:ENABlecommand.
property
¶
Return the MEASUrement:MEAS<x>:DISPlaystat:ENABle command.
Description
- This command turns on and off display of statistics in measurement badges in the user interface. This command affects only the display of statistics, basic-statistics are computed regardless of the state of this command. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DISPlaystat:ENABle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DISPlaystat:ENABle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:DISPlaystat:ENABle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?
Info
MEAS<x>specifies the measurement number.OFFturns off the display of statistics in measurement badges.ONturns on the display of statistics in measurement badges.<NR1>= 0 turns off the display of statistics in the measurement badge, any other value turns on the display of statistics.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:DISPlaystat:ENABle command.
Description
- This command turns on and off display of statistics in measurement badges in the user interface. This command affects only the display of statistics, basic-statistics are computed regardless of the state of this command. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:DISPlaystat:ENABle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:DISPlaystat:ENABle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:DISPlaystat:ENABle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?
Info
MEAS<x>specifies the measurement number.OFFturns off the display of statistics in measurement badges.ONturns on the display of statistics in measurement badges.<NR1>= 0 turns off the display of statistics in the measurement badge, any other value turns on the display of statistics.
Bases: ValidatedDynamicNumberCmd, SCPICmdWrite
The MEASUrement:MEAS<x>:EDGE<x> command.
Description
- This command sets or queries the type of the specified edge, rise or fall, for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGE<x> valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
Info
MEAS<x>specifies the measurement number.RISEspecifies the rising edge.FALLspecifies the falling edge.BOTHspecifies either the rising or falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGEIncre command.
Description
- This command sets or queries the edge increment value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEIncre?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEIncre?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEIncre valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?
Info
MEAS<x>specifies the measurement number.<NR3>is the measurements edge increment value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGEQUALifier command.
Description
- This command sets or queries the edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:EDGEQUALifier?
Info
MEAS<x>is the measurement number.CH<x>is the edge qualifier source channel.MATH<x>is the edge qualifier source math waveform;is ≥1. REF<x>is the edge qualifier source reference waveform;is ≥1.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGEQUALONE command.
Description
- This command set or queries the measurement 1 input edge qualifier one source for Efficiency measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEQUALONE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEQUALONE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEQUALONE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEQUALONE <Qstring>
- MEASUrement:MEAS<x>:EDGEQUALONE?
Info
MEAS<x>is the measurement number.<Qstring>specifies the edge qualifier source at input configuration.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGEQUALTWO command.
Description
- This command sets or queries the measurement 1 output edge qualifier two source for Efficiency measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGEQUALTWO?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGEQUALTWO?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGEQUALTWO valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGEQUALTWO <Qstring>
- MEASUrement:MEAS<x>:EDGEQUALTWO?
Info
MEAS<x>is the measurement number.<Qstring>specifies the edge qualifier source at output configuration.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:EDGES command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.fromlevel: TheMEASUrement:MEAS<x>:EDGES:FROMLevelcommand..level: TheMEASUrement:MEAS<x>:EDGES:LEVelcommand..lowerfrequency: TheMEASUrement:MEAS<x>:EDGES:LOWERFREQuencycommand..n: TheMEASUrement:MEAS<x>:EDGES:Ncommand..slewratemethod: TheMEASUrement:MEAS<x>:EDGES:SLEWRATEMethodcommand..tolevel: TheMEASUrement:MEAS<x>:EDGES:TOLevelcommand..upperfrequency: TheMEASUrement:MEAS<x>:EDGES:UPPERFREQuencycommand.
property
¶
fromlevel: MeasurementMeasItemEdgesFromlevel
Return the MEASUrement:MEAS<x>:EDGES:FROMLevel command.
Description
- This command sets or queries the ‘from level’ edge for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:FROMLevel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:FROMLevel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:FROMLevel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?
Info
MEAS<x>specifies the measurement number.MIDspecifies the MID level.HIGHspecifies the HIGH level.LOWspecifies the LOW level.
property
¶
Return the MEASUrement:MEAS<x>:EDGES:LEVel command.
Description
- This sets or queries the level type for the ‘time outside level’ measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:LEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:LEVel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:LEVel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?
Info
MEAS<x>specifies the measurement number.HIGHspecifies the HIGH level.LOWspecifies the LOW level.BOTHspecifies both the HIGH and LOW level.
property
¶
lowerfrequency: MeasurementMeasItemEdgesLowerfrequency
Return the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency command.
Description
- This command sets or queries the lower frequency for the measurement when the measurement type is phase noise. Lower frequencies are ignored. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:LOWERFREQuency?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:LOWERFREQuency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:LOWERFREQuency valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency?
Info
MEAS<x>specifies the measurement number.<NR3>is the lower frequency of the edge.
property
¶
Return the MEASUrement:MEAS<x>:EDGES:N command.
Description
- The command sets or queries the number of accumulation cycles for the measurement when the measurement type is nperiod. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:N?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:N valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?
Info
MEAS<x>specifies the measurement number.<NR3>is the maximum number of edges used by the measurement.
property
¶
slewratemethod: MeasurementMeasItemEdgesSlewratemethod
Return the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.
Description
- This command sets or queries the slew rate method for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:SLEWRATEMethod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?
Info
MEAS<x>specifies the measurement number.NOMinalspecifies the nominal slew rate method.DDRspecifies the DDR slew rate method.
property
¶
tolevel: MeasurementMeasItemEdgesTolevel
Return the MEASUrement:MEAS<x>:EDGES:TOLevel command.
Description
- This command sets or queries the ‘to level’ edge for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:TOLevel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:TOLevel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:TOLevel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?
Info
MEAS<x>specifies the measurement number.HIGHspecifies the HIGH level.MIDspecifies the MID level.LOWspecifies the LOW level.
property
¶
upperfrequency: MeasurementMeasItemEdgesUpperfrequency
Return the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency command.
Description
- This command sets or queries the upper frequency for the measurement when the measurement type is phase noise. Higher frequencies are ignored. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:UPPERFREQuency?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:UPPERFREQuency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:UPPERFREQuency valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency?
Info
MEAS<x>specifies the measurement number.<NR3>is the upper frequency of the edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGES:FROMLevel command.
Description
- This command sets or queries the ‘from level’ edge for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:FROMLevel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:FROMLevel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:FROMLevel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?
Info
MEAS<x>specifies the measurement number.MIDspecifies the MID level.HIGHspecifies the HIGH level.LOWspecifies the LOW level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGES:LEVel command.
Description
- This sets or queries the level type for the ‘time outside level’ measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:LEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:LEVel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:LEVel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?
Info
MEAS<x>specifies the measurement number.HIGHspecifies the HIGH level.LOWspecifies the LOW level.BOTHspecifies both the HIGH and LOW level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGES:LOWERFREQuency command.
Description
- This command sets or queries the lower frequency for the measurement when the measurement type is phase noise. Lower frequencies are ignored. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:LOWERFREQuency?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:LOWERFREQuency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:LOWERFREQuency valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency?
Info
MEAS<x>specifies the measurement number.<NR3>is the lower frequency of the edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGES:N command.
Description
- The command sets or queries the number of accumulation cycles for the measurement when the measurement type is nperiod. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:N?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:N valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?
Info
MEAS<x>specifies the measurement number.<NR3>is the maximum number of edges used by the measurement.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.
Description
- This command sets or queries the slew rate method for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:SLEWRATEMethod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?
Info
MEAS<x>specifies the measurement number.NOMinalspecifies the nominal slew rate method.DDRspecifies the DDR slew rate method.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGES:TOLevel command.
Description
- This command sets or queries the ‘to level’ edge for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:TOLevel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:TOLevel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:TOLevel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?
Info
MEAS<x>specifies the measurement number.HIGHspecifies the HIGH level.MIDspecifies the MID level.LOWspecifies the LOW level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EDGES:UPPERFREQuency command.
Description
- This command sets or queries the upper frequency for the measurement when the measurement type is phase noise. Higher frequencies are ignored. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EDGES:UPPERFREQuency?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EDGES:UPPERFREQuency?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EDGES:UPPERFREQuency valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency?
Info
MEAS<x>specifies the measurement number.<NR3>is the upper frequency of the edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:EEQUal command.
Description
- This command turns on or off the edge qualifier settings as input waveform to measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:EEQUal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:EEQUal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:EEQUal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:EEQUal {ON|OFF}
- MEASUrement:MEAS<x>:EEQUal?
Info
MEAS<x>specifies the measurement number.ONspecifies the edge qualifier settings has been turned on.OFFspecifies the edge qualifier settings has been turned off.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:FAILCount command.
Description
- This command returns the number of measurement failures, if applicable, for the selected measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FAILCount?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FAILCount?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:FAILCount?
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTERRANGEFROM command.
Description
- This command sets or queries harmonics filter from order. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTERRANGEFROM?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTERRANGEFROM?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTERRANGEFROM valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTERRANGEFROM <NR3>
- MEASUrement:MEAS<x>:FILTERRANGEFROM?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the filter range from value. The default value is 1.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTERRANGETO command.
Description
- This command sets or queries harmonics filter to order. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTERRANGETO?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTERRANGETO?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTERRANGETO valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTERRANGETO <NR3>
- MEASUrement:MEAS<x>:FILTERRANGETO?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the filter range to value. The default value is 50.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:FILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.blankingtime: TheMEASUrement:MEAS<x>:FILTers:BLANKingtimecommand..global: TheMEASUrement:MEAS<x>:FILTers:GLOBalcommand..highpass: TheMEASUrement:MEAS<x>:FILTers:HIGHPasscommand tree..lowpass: TheMEASUrement:MEAS<x>:FILTers:LOWPasscommand tree..ramptime: TheMEASUrement:MEAS<x>:FILTers:RAMPtimecommand.
property
¶
blankingtime: MeasurementMeasItemFiltersBlankingtime
Return the MEASUrement:MEAS<x>:FILTers:BLANKingtime command.
Description
- This command sets or queries the filter blanking time for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:BLANKingtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:BLANKingtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:BLANKingtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:BLANKingtime <NR3>
- MEASUrement:MEAS<x>:FILTers:BLANKingtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the current filter blanking time.
property
¶
global_: MeasurementMeasItemFiltersGlobal
Return the MEASUrement:MEAS<x>:FILTers:GLOBal command.
Description
- This command sets or queries the global flag for filter settings for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:FILTers:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFcauses filter settings to be changed independently for each individual measurement.ONapplies global filter settings to all the measurements’ filter settings.0causes filter settings to be changed independently for each individual measurement.1applies global filter settings to all the measurements’ filter settings.
property
¶
highpass: MeasurementMeasItemFiltersHighpass
Return the MEASUrement:MEAS<x>:FILTers:HIGHPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.freq: TheMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:FILTers:HIGHPass:SPECcommand.
property
¶
lowpass: MeasurementMeasItemFiltersLowpass
Return the MEASUrement:MEAS<x>:FILTers:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.freq: TheMEASUrement:MEAS<x>:FILTers:LOWPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:FILTers:LOWPass:SPECcommand.
property
¶
ramptime: MeasurementMeasItemFiltersRamptime
Return the MEASUrement:MEAS<x>:FILTers:RAMPtime command.
Description
- This command sets or queries the filter ramp time for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:RAMPtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:RAMPtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:RAMPtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:RAMPtime <NR3>
- MEASUrement:MEAS<x>:FILTers:RAMPtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the current filter ramp time.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:BLANKingtime command.
Description
- This command sets or queries the filter blanking time for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:BLANKingtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:BLANKingtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:BLANKingtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:BLANKingtime <NR3>
- MEASUrement:MEAS<x>:FILTers:BLANKingtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the current filter blanking time.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:GLOBal command.
Description
- This command sets or queries the global flag for filter settings for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:FILTers:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFcauses filter settings to be changed independently for each individual measurement.ONapplies global filter settings to all the measurements’ filter settings.0causes filter settings to be changed independently for each individual measurement.1applies global filter settings to all the measurements’ filter settings.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:HIGHPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.freq: TheMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:FILTers:HIGHPass:SPECcommand.
property
¶
Return the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ command.
Description
- This command sets or queries the high pass filter frequency for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>is the current high pass filter frequency.
property
¶
Return the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC command.
Description
- This command sets or queries the high pass filter order for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies no filter.FIRSTspecifies a first-order filter.SECONDspecifies a second-order filter.THIRDspecifies a third-order filter.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ command.
Description
- This command sets or queries the high pass filter frequency for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>is the current high pass filter frequency.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC command.
Description
- This command sets or queries the high pass filter order for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies no filter.FIRSTspecifies a first-order filter.SECONDspecifies a second-order filter.THIRDspecifies a third-order filter.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.freq: TheMEASUrement:MEAS<x>:FILTers:LOWPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:FILTers:LOWPass:SPECcommand.
property
¶
Return the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ command.
Description
- This command sets or queries the low pass filter cutoff frequency for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>is the current low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.
property
¶
Return the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC command.
Description
- This command sets or queries the low pass filter order for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies no filter.FIRSTspecifies a first-order filter.SECONDspecifies a second-order filter.THIRDspecifies a third-order filter.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ command.
Description
- This command sets or queries the low pass filter cutoff frequency for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>is the current low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC command.
Description
- This command sets or queries the low pass filter order for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies no filter.FIRSTspecifies a first-order filter.SECONDspecifies a second-order filter.THIRDspecifies a third-order filter.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FILTers:RAMPtime command.
Description
- This command sets or queries the filter ramp time for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FILTers:RAMPtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FILTers:RAMPtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FILTers:RAMPtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FILTers:RAMPtime <NR3>
- MEASUrement:MEAS<x>:FILTers:RAMPtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the current filter ramp time.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FREQ command.
Description
- This command sets or queries switching frequency for Switching Ripple measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FREQ <NR3>
- MEASUrement:MEAS<x>:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the switching frequency. The default is 100k Hz, The minimum is 50 Hz, and the maximum is 1 GHz.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FROMedge command.
Description
- This command sets or queries the from edge type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMedge?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMedge?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMedge valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?
Info
MEAS<x>specifies the measurement number.FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both the rising and falling edges of the waveform.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.
Description
- This command sets or queries the from edge search direction for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMEDGESEARCHDIRect valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?
Info
MEAS<x>specifies the measurement number.FORWardspecifies a forward search from the edge.BACKWardspecifies a backward search from the edge.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:FROMSymbol command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.logic2source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrcecommand..logic3source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrcecommand..logic4source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrcecommand..logic5source: TheMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrcecommand..measureat: TheMEASUrement:MEAS<x>:FROMSymbol:MEASUREATcommand.
property
¶
logic2source: MeasurementMeasItemFromsymbolLogic2source
Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 1 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 1 From Symbol to H (High).Lsets the logic source 1 From Symbol to L (Low).Xsets the logic source 1 From Symbol to X (Don’t care).
property
¶
logic3source: MeasurementMeasItemFromsymbolLogic3source
Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 2 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 2 From Symbol to H (High).Lsets the logic source 2 From Symbol to L (Low).Xsets the logic source 2 From Symbol to X (Don’t care).
property
¶
logic4source: MeasurementMeasItemFromsymbolLogic4source
Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 3 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 3 From Symbol to H (High).Lsets the logic source 3 From Symbol to L (Low).Xsets the logic source 3 From Symbol to X (Don’t care).
property
¶
logic5source: MeasurementMeasItemFromsymbolLogic5source
Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 4 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 4 From Symbol to H (High).Lsets the logic source 4 From Symbol to L (Low).Xsets the logic source 4 From Symbol to X (Don’t care).
property
¶
measureat: MeasurementMeasItemFromsymbolMeasureat
Return the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT command.
Description
- This command sets or queries the DDR digital measurement From Symbol MeasureAT value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:MEASUREAT valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?
Info
MEAS<x>specifies the measurement number.Startsets the FromSymbol MeasureAT to Start.Stopsets the FromSymbol MeasureAT to Stop.ClockEdgesets the FromSymbol MeasureAT to ClockEdge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 1 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 1 From Symbol to H (High).Lsets the logic source 1 From Symbol to L (Low).Xsets the logic source 1 From Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 2 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 2 From Symbol to H (High).Lsets the logic source 2 From Symbol to L (Low).Xsets the logic source 2 From Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 3 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 3 From Symbol to H (High).Lsets the logic source 3 From Symbol to L (Low).Xsets the logic source 3 From Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 4 source From symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 4 From Symbol to H (High).Lsets the logic source 4 From Symbol to L (Low).Xsets the logic source 4 From Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT command.
Description
- This command sets or queries the DDR digital measurement From Symbol MeasureAT value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FROMSymbol:MEASUREAT valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?
Info
MEAS<x>specifies the measurement number.Startsets the FromSymbol MeasureAT to Start.Stopsets the FromSymbol MeasureAT to Stop.ClockEdgesets the FromSymbol MeasureAT to ClockEdge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:FUNDCURRent command.
Description
- This command sets or queries the fundamental current value for IEC-Class C type harmonics standard. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:FUNDCURRent?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:FUNDCURRent?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:FUNDCURRent valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:FUNDCURRent <NR3>
- MEASUrement:MEAS<x>:FUNDCURRent?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the fundamental current for class C harmonics standard.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GATing command.
Description
- This command sets or queries the gating type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing?
Info
MEAS<x>is the measurement number for which to return a value.NONEspecifies measurements are taken across the entire record.SCREENturns on gating, using the left and right edges of the screen.CURSorlimits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.LOGicspecifies that measurements are taken only when the logical state of other waveforms is true.SEARchspecifies that measurements are taken only where the results of a user specified search are found.TIMelimits measurements to the portion of the waveform between the Start and End gate times.
Properties
.active: TheMEASUrement:MEAS<x>:GATing:ACTivecommand..endtime: TheMEASUrement:MEAS<x>:GATing:ENDtimecommand..global: TheMEASUrement:MEAS<x>:GATing:GLOBalcommand..hysteresis: TheMEASUrement:MEAS<x>:GATing:HYSTeresiscommand..logicsource: TheMEASUrement:MEAS<x>:GATing:LOGICSourcecommand..midref: TheMEASUrement:MEAS<x>:GATing:MIDRefcommand..searchsource: TheMEASUrement:MEAS<x>:GATing:SEARCHSourcecommand..starttime: TheMEASUrement:MEAS<x>:GATing:STARTtimecommand.
property
¶
active: MeasurementMeasItemGatingActive
Return the MEASUrement:MEAS<x>:GATing:ACTive command.
Description
- This command sets or queries the gating active level when the gating type is logic. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:ACTive?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:ACTive?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:ACTive valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?
Info
MEAS<x>specifies the measurement number.HIGHtakes a measurement when logic gating is High.LOWtakes a measurement when logic gating Low.
property
¶
endtime: MeasurementMeasItemGatingEndtime
Return the MEASUrement:MEAS<x>:GATing:ENDtime command.
Description
- Sets or queries the end gate time for the measurement when using Local gating.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:ENDtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:ENDtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:ENDtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.
property
¶
global_: MeasurementMeasItemGatingGlobal
Return the MEASUrement:MEAS<x>:GATing:GLOBal command.
Description
- This command sets or queries the gating settings global flag. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFspecifies gate settings can be changed independently for each individual measurement.ONapplies global gate settings to all the measurements’ gate settings.0specifies gate settings can be changed independently for each individual measurement.1applies global gate settings to all the measurements’ gate settings.
property
¶
hysteresis: MeasurementMeasItemGatingHysteresis
Return the MEASUrement:MEAS<x>:GATing:HYSTeresis command.
Description
- This command sets or queries the gating hysteresis value when the gating type is logic. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?
Info
MEAS<x>specifies the measurement number.<NR3>is the gating hysteresis.
property
¶
logicsource: MeasurementMeasItemGatingLogicsource
Return the MEASUrement:MEAS<x>:GATing:LOGICSource command.
Description
- This command sets or queries the gating data source when the gating type is logic. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:LOGICSource valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:LOGICSource {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
Info
MEAS<x>specifies the measurement number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
property
¶
midref: MeasurementMeasItemGatingMidref
Return the MEASUrement:MEAS<x>:GATing:MIDRef command.
Description
- This command sets or queries the gating mid ref value when the gating type is logic. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:MIDRef?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:MIDRef?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:MIDRef valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?
Info
MEAS<x>specifies the measurement number.<NR3>is the mid ref value for gating.
property
¶
searchsource: MeasurementMeasItemGatingSearchsource
Return the MEASUrement:MEAS<x>:GATing:SEARCHSource command.
Description
- This command sets or queries the gating search source when the gating type is search. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:SEARCHSource valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
Info
MEAS<x>specifies the measurement number.SEARCH1is the gating source for search gating.
property
¶
starttime: MeasurementMeasItemGatingStarttime
Return the MEASUrement:MEAS<x>:GATing:STARTtime command.
Description
- Sets or queries the start gate time for the measurement when using Local gating.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:STARTtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:STARTtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:STARTtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GATing:ACTive command.
Description
- This command sets or queries the gating active level when the gating type is logic. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:ACTive?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:ACTive?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:ACTive valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?
Info
MEAS<x>specifies the measurement number.HIGHtakes a measurement when logic gating is High.LOWtakes a measurement when logic gating Low.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GATing:ENDtime command.
Description
- Sets or queries the end gate time for the measurement when using Local gating.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:ENDtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:ENDtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:ENDtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GATing:GLOBal command.
Description
- This command sets or queries the gating settings global flag. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFspecifies gate settings can be changed independently for each individual measurement.ONapplies global gate settings to all the measurements’ gate settings.0specifies gate settings can be changed independently for each individual measurement.1applies global gate settings to all the measurements’ gate settings.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GATing:HYSTeresis command.
Description
- This command sets or queries the gating hysteresis value when the gating type is logic. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?
Info
MEAS<x>specifies the measurement number.<NR3>is the gating hysteresis.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:GATing:LOGICSource command.
Description
- This command sets or queries the gating data source when the gating type is logic. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:LOGICSource valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:LOGICSource {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
Info
MEAS<x>specifies the measurement number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GATing:MIDRef command.
Description
- This command sets or queries the gating mid ref value when the gating type is logic. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:MIDRef?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:MIDRef?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:MIDRef valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?
Info
MEAS<x>specifies the measurement number.<NR3>is the mid ref value for gating.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:GATing:SEARCHSource command.
Description
- This command sets or queries the gating search source when the gating type is search. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:SEARCHSource valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
Info
MEAS<x>specifies the measurement number.SEARCH1is the gating source for search gating.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GATing:STARTtime command.
Description
- Sets or queries the start gate time for the measurement when using Local gating.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GATing:STARTtime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GATing:STARTtime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GATing:STARTtime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?
Info
MEAS<x>specifies the measurement number.<NR3>is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:GLOBalref command.
Description
- This command sets or queries the reference levels global flag for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:GLOBalref?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:GLOBalref?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:GLOBalref valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?
Info
MEAS<x>specifies the measurement number.OFFallows ref levels to be set separately for each measurement.ONapplies the same ref levels to all measurements.0allows ref levels to be set separately for each measurement.1applies the same ref levels to all measurements.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HARMONICSCLass command.
Description
- This command sets or queries the class type for the harmonics measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSCLass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSCLass?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSCLass valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSCLass {CLASSA|CLASSB|CLASSC|CLASSD}
- MEASUrement:MEAS<x>:HARMONICSCLass?
Info
MEAS<x>specifies the measurement number.CLASSA-Dspecifies the class type.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HARMONICSSOURce command.
Description
- This command sets or queries harmonics source. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSSOURce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSSOURce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSSOURce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSSOURce {CURRENT|VOLTAGE}
- MEASUrement:MEAS<x>:HARMONICSSOURce?
Info
MEAS<x>specifies the measurement number.CURRENTspecifies current as the harmonics source.VOLTAGEspecifies voltage as the harmonics source.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HARMONICSStd command.
Description
- This command sets or queries harmonics standard. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSStd?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSStd?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSStd valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSStd {NONE|IEC|IEEE519|CUSTOM}
- MEASUrement:MEAS<x>:HARMONICSStd?
Info
MEAS<x>specifies the measurement number.NONEspecifies none as the harmonics test standard.IECspecifies IEC as the harmonics test standard.IEEE519specifies IEEE519 as the harmonics test standard.CUSTOMspecifies that there is a custom harmonics test standard.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HARMONICSUNits command.
Description
- This command sets or queries harmonics units. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HARMONICSUNits?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HARMONICSUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HARMONICSUNits valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HARMONICSUNits {LOGARITHM|LINEAR}
- MEASUrement:MEAS<x>:HARMONICSUNits?
Info
MEAS<x>specifies the measurement number.LOGARITHMspecifies logarithmic as the harmonics units.LINEARspecifies linear as the harmonics units.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.configuration: TheMEASUrement:MEAS<x>:HIGHLEVel:CONFIGurationcommand..l2ltol2n: TheMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2Ncommand..lineselected: TheMEASUrement:MEAS<x>:HIGHLEVel:LINESelectedcommand..outl2ltol2n: TheMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2Ncommand..outlineselected: TheMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelectedcommand..outwiring: TheMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRingcommand..useglobal: TheMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBALcommand..wiring: TheMEASUrement:MEAS<x>:HIGHLEVel:WIRingcommand.
property
¶
configuration: MeasurementMeasItemHighlevelConfiguration
Return the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration command.
Description
- This command sets or queries the local input and output configuration.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?
Info
MEAS<x>specifies the measurement number.INPUTspecifies the local Input or Output source settings as input.OUTPUTspecifies the local Input or Output source settings as output.
property
¶
l2ltol2n: MeasurementMeasItemHighlevelL2ltol2n
Return the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N command.
Description
- This command sets or queries local input Line-to-Line to Line-to-Neutral Conversion.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?
property
¶
lineselected: MeasurementMeasItemHighlevelLineselected
Return the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected command.
Description
- This command sets or queries local input select lines.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:LINESelected?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:LINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:LINESelected valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected?
Info
ABCBspecifies the local input select lines as ABCB.ACBCspecifies the local input select lines as ACBC.BACAspecifies the local input select lines as BACA.ANspecifies the local input select lines as AN.BNspecifies the local input select lines as BN.CNspecifies the local input select lines as CN.
property
¶
outl2ltol2n: MeasurementMeasItemHighlevelOutl2ltol2n
Return the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N command.
Description
- This command sets or queries local output Line-to-Line to Line-to-Neutral Conversion .
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?
property
¶
outlineselected: MeasurementMeasItemHighlevelOutlineselected
Return the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected command.
Description
- This command sets or queries local output select lines.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?
Info
XYZYspecifies the local output select lines as XYZY.XZYZspecifies the local output select lines as XZYZ.YXZXspecifies the local output select lines as YXZX.XNspecifies the local output select lines as XN.YNspecifies the local output select lines as YN.ZNspecifies the local output select lines as ZN.
property
¶
outwiring: MeasurementMeasItemHighlevelOutwiring
Return the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing command.
Description
- This command sets or queries the local output wiring.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?
Info
MEAS<x>specifies the measurement number.P1W2V1I1specifies P1W2V1I1 as the local output wiring.P1W3V2I2specifies P1W3V2I2 as the local output wiring.P3W3V3I3specifies P3W3V3I3 as the local output wiring.P3W4specifies P3W4 as the local output wiring.DCP1W2specifies DCP1W2 as the local output wiring.
property
¶
useglobal: MeasurementMeasItemHighlevelUseglobal
Return the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL command.
Description
- This command sets or queries the IMDA source settings as global or local.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL {ON|OFF|1|0}
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?
Info
MEAS<x>specifies the measurement number.1specifies the source settings as global.0specifies the source settings as local.ONspecifies the source settings as global.OFFspecifies the source settings as local.
property
¶
Return the MEASUrement:MEAS<x>:HIGHLEVel:WIRing command.
Description
- This command sets or queries the local Input wiring.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:WIRing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:WIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:WIRing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing?
Info
MEAS<x>specifies the measurement number.P1W2V1I1specifies P1W2V1I1 as the local input wiring.P1W3V2I2specifies P1W3V2I2 as the local input wiring.P3W3V2I2specifies P3W3V2I2 as the local input wiring.P3W3V3I3specifies P3W3V3I3 as the local input wiring.P3W3specifies P3W3 as the local input wiring.DCP1W2specifies DCP1W2 as the local input wiring.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration command.
Description
- This command sets or queries the local input and output configuration.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?
Info
MEAS<x>specifies the measurement number.INPUTspecifies the local Input or Output source settings as input.OUTPUTspecifies the local Input or Output source settings as output.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N command.
Description
- This command sets or queries local input Line-to-Line to Line-to-Neutral Conversion.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:LINESelected command.
Description
- This command sets or queries local input select lines.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:LINESelected?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:LINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:LINESelected valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected?
Info
ABCBspecifies the local input select lines as ABCB.ACBCspecifies the local input select lines as ACBC.BACAspecifies the local input select lines as BACA.ANspecifies the local input select lines as AN.BNspecifies the local input select lines as BN.CNspecifies the local input select lines as CN.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N command.
Description
- This command sets or queries local output Line-to-Line to Line-to-Neutral Conversion .
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected command.
Description
- This command sets or queries local output select lines.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?
Info
XYZYspecifies the local output select lines as XYZY.XZYZspecifies the local output select lines as XZYZ.YXZXspecifies the local output select lines as YXZX.XNspecifies the local output select lines as XN.YNspecifies the local output select lines as YN.ZNspecifies the local output select lines as ZN.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing command.
Description
- This command sets or queries the local output wiring.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?
Info
MEAS<x>specifies the measurement number.P1W2V1I1specifies P1W2V1I1 as the local output wiring.P1W3V2I2specifies P1W3V2I2 as the local output wiring.P3W3V3I3specifies P3W3V3I3 as the local output wiring.P3W4specifies P3W4 as the local output wiring.DCP1W2specifies DCP1W2 as the local output wiring.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL command.
Description
- This command sets or queries the IMDA source settings as global or local.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL {ON|OFF|1|0}
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?
Info
MEAS<x>specifies the measurement number.1specifies the source settings as global.0specifies the source settings as local.ONspecifies the source settings as global.OFFspecifies the source settings as local.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHLEVel:WIRing command.
Description
- This command sets or queries the local Input wiring.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHLEVel:WIRing?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:WIRing?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHLEVel:WIRing valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing?
Info
MEAS<x>specifies the measurement number.P1W2V1I1specifies P1W2V1I1 as the local input wiring.P1W3V2I2specifies P1W3V2I2 as the local input wiring.P3W3V2I2specifies P3W3V2I2 as the local input wiring.P3W3V3I3specifies P3W3V3I3 as the local input wiring.P3W3specifies P3W3 as the local input wiring.DCP1W2specifies DCP1W2 as the local input wiring.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HIGHREFVoltage command.
Description
- This command sets or queries the high reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HIGHREFVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HIGHREFVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HIGHREFVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?
Info
MEAS<x>specifies the measurement number.<NR3>is the high reference voltage value for the selected configuration.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:HLEVel command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HLEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HLEVel?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.output: TheMEASUrement:MEAS<x>:HLEVel:OUTPutcommand tree.
property
¶
output: MeasurementMeasItemHlevelOutput
Return the MEASUrement:MEAS<x>:HLEVel:OUTPut command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.uglobal: TheMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobalcommand.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:HLEVel:OUTPut command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.uglobal: TheMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobalcommand.
property
¶
Return the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal command.
Description
- This command turns on or off output global settings for measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal {ON|OFF}
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?
Info
ONsets the output global settings for measurement to on.OFFsets the output global settings for measurement to off.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal command.
Description
- This command turns on or off output global settings for measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal {ON|OFF}
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?
Info
ONsets the output global settings for measurement to on.OFFsets the output global settings for measurement to off.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HTORque command.
Description
- This command sets or queries the measurement High Torque value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HTORque?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HTORque?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HTORque valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HTORque <NR1>
- MEASUrement:MEAS<x>:HTORque?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the High Torque value of the measurement in the range of 11 to 10000000.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:HVOLtage command.
Description
- This command sets or queries the measurement Torque High Voltage value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:HVOLtage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:HVOLtage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:HVOLtage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:HVOLtage <NR1>
- MEASUrement:MEAS<x>:HVOLtage?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the High Voltage value of the measurement in the range of 1 to 100.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:IDLETime command.
Description
- This command sets or queries the idle time for the measurement when the measurement type is burst width. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:IDLETime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:IDLETime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:IDLETime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?
Info
MEAS<x>specifies the measurement number.<NR3>is the idle time.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:INPUTLEVel command.
Description
- Sets or queries the input trigger voltage level.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:INPUTLEVel?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:INPUTLEVel?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:INPUTLEVel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:INPUTLEVel <NR2>
- MEASUrement:MEAS<x>:INPUTLEVel?
Info
MEAS<x>is the measurement number.<NR2>is the trigger voltage, in the range of -500 V to +500 V.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:INPUTPOwer command.
Description
- This command sets or queries the input power value for IEC-Class C and Class D harmonics standard .
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:INPUTPOwer?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:INPUTPOwer?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:INPUTPOwer valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:INPUTPOwer <NR3>
- MEASUrement:MEAS<x>:INPUTPOwer?
Info
MEAS<x>is the measurement number.<NR3>specifies the input power value for class C harmonics standard.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.dcd: TheMEASUrement:MEAS<x>:JITTERSummary:DCDcommand..ddj: TheMEASUrement:MEAS<x>:JITTERSummary:DDJcommand..djdd: TheMEASUrement:MEAS<x>:JITTERSummary:DJDDcommand..eyewidthber: TheMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBERcommand..npj: TheMEASUrement:MEAS<x>:JITTERSummary:NPJcommand..pj: TheMEASUrement:MEAS<x>:JITTERSummary:PJcommand..rjdd: TheMEASUrement:MEAS<x>:JITTERSummary:RJDDcommand..tie: TheMEASUrement:MEAS<x>:JITTERSummary:TIEcommand..tjber: TheMEASUrement:MEAS<x>:JITTERSummary:TJBERcommand.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:DCD command.
Description
- This command sets or queries whether DCD is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:DCD?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DCD?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DCD valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:DCD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DCD?
Info
MEAS<x>specifies the measurement number.1adds the DCD measurement as part of jitter summary.0do not add the DCD measurement as part of jitter summary.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:DDJ command.
Description
- This command sets or queries whether DDJ is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:DDJ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DDJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DDJ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:DDJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DDJ?
Info
MEAS<x>specifies the measurement number.1adds the DDJ measurement as part of jitter summary.0do not add the DDJ measurement as part of jitter summary.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:DJDD command.
Description
- This command sets or queries whether DJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:DJDD?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DJDD?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DJDD valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:DJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJDD?
Info
MEAS<x>specifies the measurement number.1add the DJDD measurement as part of jitter summary.0do not add the DJDD measurement as part of jitter summary.
property
¶
eyewidthber: MeasurementMeasItemJittersummaryEyewidthber
Return the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER command.
Description
- This command sets or queries whether EyeWidth@BER is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?
Info
MEAS<x>specifies the measurement number.1add the EyeWidth@BER measurement as part of jitter summary.0do not add the EyeWidth@BER measurement as part of jitter summary.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:NPJ command.
Description
- This command sets or queries whether NPJ is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:NPJ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:NPJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:NPJ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:NPJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:NPJ?
Info
MEAS<x>specifies the measurement number.1add the NPJ measurement as part of jitter summary.0do not add the NPJ measurement as part of jitter summary.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:PJ command.
Description
- This command sets or queries whether PJ is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:PJ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:PJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:PJ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:PJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PJ?
Info
MEAS<x>specifies the measurement number.1add the PJ measurement as part of jitter summary.0do not add the PJ measurement as part of jitter summary.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:RJDD command.
Description
- This command sets or queries whether RJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:RJDD?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:RJDD?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:RJDD valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:RJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJDD?
Info
MEAS<x>specifies the measurement number.1add the RJ-dd measurement as part of jitter summary.0do not add the RJ-dd measurement as part of jitter summary.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:TIE command.
Description
- This command sets or queries whether TIE is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:TIE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TIE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TIE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:TIE {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TIE?
Info
MEAS<x>specifies the measurement number.1add the TIE measurement as part of jitter summary.0do not add the TIE measurement as part of jitter summary.
property
¶
Return the MEASUrement:MEAS<x>:JITTERSummary:TJBER command.
Description
- This command sets or queries whether TJ@BER is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:TJBER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TJBER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TJBER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:TJBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TJBER?
Info
MEAS<x>specifies the measurement number.1add the TJ@BER measurement as part of jitter summary.0do not add the TJ@BER measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:DCD command.
Description
- This command sets or queries whether DCD is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:DCD?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DCD?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DCD valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:DCD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DCD?
Info
MEAS<x>specifies the measurement number.1adds the DCD measurement as part of jitter summary.0do not add the DCD measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:DDJ command.
Description
- This command sets or queries whether DDJ is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:DDJ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DDJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DDJ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:DDJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DDJ?
Info
MEAS<x>specifies the measurement number.1adds the DDJ measurement as part of jitter summary.0do not add the DDJ measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:DJDD command.
Description
- This command sets or queries whether DJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:DJDD?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DJDD?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:DJDD valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:DJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJDD?
Info
MEAS<x>specifies the measurement number.1add the DJDD measurement as part of jitter summary.0do not add the DJDD measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER command.
Description
- This command sets or queries whether EyeWidth@BER is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?
Info
MEAS<x>specifies the measurement number.1add the EyeWidth@BER measurement as part of jitter summary.0do not add the EyeWidth@BER measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:NPJ command.
Description
- This command sets or queries whether NPJ is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:NPJ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:NPJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:NPJ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:NPJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:NPJ?
Info
MEAS<x>specifies the measurement number.1add the NPJ measurement as part of jitter summary.0do not add the NPJ measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:PJ command.
Description
- This command sets or queries whether PJ is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:PJ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:PJ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:PJ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:PJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PJ?
Info
MEAS<x>specifies the measurement number.1add the PJ measurement as part of jitter summary.0do not add the PJ measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:RJDD command.
Description
- This command sets or queries whether RJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:RJDD?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:RJDD?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:RJDD valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:RJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJDD?
Info
MEAS<x>specifies the measurement number.1add the RJ-dd measurement as part of jitter summary.0do not add the RJ-dd measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:TIE command.
Description
- This command sets or queries whether TIE is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:TIE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TIE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TIE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:TIE {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TIE?
Info
MEAS<x>specifies the measurement number.1add the TIE measurement as part of jitter summary.0do not add the TIE measurement as part of jitter summary.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:JITTERSummary:TJBER command.
Description
- This command sets or queries whether TJ@BER is included in the jitter summary for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:JITTERSummary:TJBER?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TJBER?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:JITTERSummary:TJBER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:JITTERSummary:TJBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TJBER?
Info
MEAS<x>specifies the measurement number.1add the TJ@BER measurement as part of jitter summary.0do not add the TJ@BER measurement as part of jitter summary.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:LABel command.
Description
- This command sets or queries the label for the measurement. As the label can contain non 7-bit ASCII text, it is stored in Percent Encoding format. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:LABel valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LABel <QString>
Info
MEAS<x>specifies the measurement number.<QString>is the measurement label.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:LINESelected command.
Description
- This command sets or queries selected lines for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LINESelected?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LINESelected?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LINESelected valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LINESelected {ABCB|ACBC|BACA|XYZY|XZYZ|YXZX}
- MEASUrement:MEAS<x>:LINESelected?
Info
MEAS<x>specifies the measurement number.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:LOWREFVoltage command.
Description
- This command sets or queries the low reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LOWREFVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LOWREFVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LOWREFVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?
Info
MEAS<x>specifies the measurement number.<NR3>is the low reference voltage value for the selected configuration.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:LTORque command.
Description
- This command sets or queries the measurement Low Torque value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LTORque?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LTORque?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LTORque valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LTORque <NR1>
- MEASUrement:MEAS<x>:LTORque?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the Low Torque value of the measurement in the range of 0 to 10000000.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:LTYPe command.
Description
- This command sets or returns the value for the level type as auto or custom. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LTYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LTYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LTYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LTYPe {AUTO|CUSTom}
- MEASUrement:MEAS<x>:LTYPe?
Info
AUTOspecifies the value for the level type as auto.CUSTomspecifies the value for the level type as custom.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:LUNITs command.
Description
- This command sets or returns the value for the level units as percentage or absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LUNITs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LUNITs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LUNITs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LUNITs {PERCent|ABSolute}
- MEASUrement:MEAS<x>:LUNITs?
Info
PERCentspecifies the value for the level units as percent.ABSolutespecifies the value for the level units as absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:LVOLtage command.
Description
- This command sets or queries the measurement Torque Low Voltage value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:LVOLtage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:LVOLtage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:LVOLtage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:LVOLtage <NR1>
- MEASUrement:MEAS<x>:LVOLtage?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the Low Voltage value of the measurement in the range of -100 to 100.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MAXCUrrent command.
Description
- This command sets or returns the maximum current. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXCUrrent?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXCUrrent?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXCUrrent valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXCUrrent <NR3>
- MEASUrement:MEAS<x>:MAXCUrrent?
Info
<NR3>specifies the maximum current.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MAXCycle command.
Description
- This command sets or queries the maximum cycle value for the DDRTERRN and DDRTERRMN measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXCycle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXCycle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXCycle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXCycle <NR1>
- MEASUrement:MEAS<x>:MAXCycle?
Info
MEAS<x>specifies the measurement number.<NR1>is the maximum cycle range limit value in the range or 2 to 50.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MAXGVoltage command.
Description
- This command sets or returns the maximum gate voltage. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXGVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXGVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXGVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXGVoltage <NR3>
- MEASUrement:MEAS<x>:MAXGVoltage?
Info
<NR3>specifies the maximum gate voltage.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MAXVoltage command.
Description
- Sets or queries the maximum input voltage. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MAXVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MAXVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MAXVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MAXVoltage <NR2>
- MEASUrement:MEAS<x>:MAXVoltage?
Info
<NR2>is the maximum input voltage, in the range of -61 V to +61 V.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:MEASRange command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.global: TheMEASUrement:MEAS<x>:MEASRange:GLOBalcommand..max: TheMEASUrement:MEAS<x>:MEASRange:MAXcommand..min: TheMEASUrement:MEAS<x>:MEASRange:MINcommand..state: TheMEASUrement:MEAS<x>:MEASRange:STATEcommand.
property
¶
global_: MeasurementMeasItemMeasrangeGlobal
Return the MEASUrement:MEAS<x>:MEASRange:GLOBal command.
Description
- This command sets or queries the range settings global flag for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFspecifies that range settings can be set independently for each individual measurement.ONapplies global measurement range settings to all the measurements’ range settings.0specifies that range settings can be set independently for each individual measurement.1applies global measurement range settings to all the measurements’ range settings.
property
¶
Return the MEASUrement:MEAS<x>:MEASRange:MAX command.
Description
- This command sets or queries the range maximum value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:MAX?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:MAX?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:MAX valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:MAX <NR3>
- MEASUrement:MEAS<x>:MEASRange:MAX?
Info
MEAS<x>specifies the measurement number.<NR3>is the maximum measurement range limit value.
property
¶
Return the MEASUrement:MEAS<x>:MEASRange:MIN command.
Description
- This command sets or queries the range minimum value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:MIN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:MIN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:MIN valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:MIN <NR3>
- MEASUrement:MEAS<x>:MEASRange:MIN?
Info
MEAS<x>specifies the measurement number.<NR3>is the minimum measurement range limit value.
property
¶
Return the MEASUrement:MEAS<x>:MEASRange:STATE command.
Description
- This command sets or queries the range state for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:STATE?
Info
MEAS<x>specifies the measurement number.OFFturns off the measurement range limits.ONturns on the measurement range limits.0turns off the measurement range limits.1turns on the measurement range limits.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MEASRange:GLOBal command.
Description
- This command sets or queries the range settings global flag for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFspecifies that range settings can be set independently for each individual measurement.ONapplies global measurement range settings to all the measurements’ range settings.0specifies that range settings can be set independently for each individual measurement.1applies global measurement range settings to all the measurements’ range settings.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MEASRange:MAX command.
Description
- This command sets or queries the range maximum value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:MAX?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:MAX?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:MAX valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:MAX <NR3>
- MEASUrement:MEAS<x>:MEASRange:MAX?
Info
MEAS<x>specifies the measurement number.<NR3>is the maximum measurement range limit value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MEASRange:MIN command.
Description
- This command sets or queries the range minimum value for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:MIN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:MIN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:MIN valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:MIN <NR3>
- MEASUrement:MEAS<x>:MEASRange:MIN?
Info
MEAS<x>specifies the measurement number.<NR3>is the minimum measurement range limit value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MEASRange:STATE command.
Description
- This command sets or queries the range state for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MEASRange:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MEASRange:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MEASRange:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:STATE?
Info
MEAS<x>specifies the measurement number.OFFturns off the measurement range limits.ONturns on the measurement range limits.0turns off the measurement range limits.1turns on the measurement range limits.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:MECH command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.eindexz: TheMEASUrement:MEAS<x>:MECH:EINDexzcommand..gratio: TheMEASUrement:MEAS<x>:MECH:GRATiocommand..munits: TheMEASUrement:MEAS<x>:MECH:MUNitscommand..ppairs: TheMEASUrement:MEAS<x>:MECH:PPAirscommand..pprotation: TheMEASUrement:MEAS<x>:MECH:PPRotationcommand..stype: TheMEASUrement:MEAS<x>:MECH:STYPecommand.
property
¶
eindexz: MeasurementMeasItemMechEindexz
Return the MEASUrement:MEAS<x>:MECH:EINDexz command.
Description
- This command sets or queries the specified mechanical Index Z source. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:EINDexz?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:EINDexz?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:EINDexz valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MECH:EINDexz?
Info
ONspecifies the Index Z check box state as enabled.OFFspecifies the Index Z check box state as disabled.1specifies the Index Z check box state as enabled.0specifies the Index Z check box state as disabled.
property
¶
gratio: MeasurementMeasItemMechGratio
Return the MEASUrement:MEAS<x>:MECH:GRATio command.
Description
- This command sets or queries the gear ratio for the specific measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:GRATio?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:GRATio?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:GRATio valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:GRATio <NR3>
- MEASUrement:MEAS<x>:MECH:GRATio?
Info
<NR3>defines the gear ratio value for specified measurement. The minimum to maximum range is 0.001-1000.
property
¶
munits: MeasurementMeasItemMechMunits
Return the MEASUrement:MEAS<x>:MECH:MUNits command.
Description
- This command sets or queries the specified mechanical measurement results units. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:MUNits?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:MUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:MUNits valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MEAS<x>:MECH:MUNits?
Info
NMdefines the results units of the measurement as NM.OZINCHdefines the results units of the measurement as OZINCH.FTLBdefines the results units of the measurement as FTLB.INCHLBdefines the results units of the measurement as INCHLB.DEGREESdefines the results units of the measurement as DEGREES.RADIANSdefines the results units of the measurement as RADIANS.
property
¶
ppairs: MeasurementMeasItemMechPpairs
Return the MEASUrement:MEAS<x>:MECH:PPAirs command.
Description
- This command sets or queries the number of pole pairs for the specific measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:PPAirs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:PPAirs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:PPAirs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:PPAirs <NR1>
- MEASUrement:MEAS<x>:MECH:PPAirs?
Info
<NR1>defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.
property
¶
pprotation: MeasurementMeasItemMechPprotation
Return the MEASUrement:MEAS<x>:MECH:PPRotation command.
Description
- This command sets or queries the specified pulses per rotation of the measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:PPRotation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:PPRotation?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:PPRotation valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:PPRotation <NR1>
- MEASUrement:MEAS<x>:MECH:PPRotation?
Info
MEAS<x>specifies the measurement number.<NR1>defines the pulses per rotation of the measurement in the range of 1 to 10000.
property
¶
stype: MeasurementMeasItemMechStype
Return the MEASUrement:MEAS<x>:MECH:STYPe command.
Description
- This command sets or queries the local measurement sensor type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:STYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:STYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:STYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:STYPe {HSENSOR|QEI}
- MEASUrement:MEAS<x>:MECH:STYPe?
Info
MEAS<x>specifies the measurement number.HSENSORspecifies the sensor type as HSENSOR.QEIspecifies the sensor type as QEI.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MECH:EINDexz command.
Description
- This command sets or queries the specified mechanical Index Z source. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:EINDexz?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:EINDexz?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:EINDexz valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MECH:EINDexz?
Info
ONspecifies the Index Z check box state as enabled.OFFspecifies the Index Z check box state as disabled.1specifies the Index Z check box state as enabled.0specifies the Index Z check box state as disabled.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MECH:GRATio command.
Description
- This command sets or queries the gear ratio for the specific measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:GRATio?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:GRATio?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:GRATio valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:GRATio <NR3>
- MEASUrement:MEAS<x>:MECH:GRATio?
Info
<NR3>defines the gear ratio value for specified measurement. The minimum to maximum range is 0.001-1000.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MECH:MUNits command.
Description
- This command sets or queries the specified mechanical measurement results units. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:MUNits?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:MUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:MUNits valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MEAS<x>:MECH:MUNits?
Info
NMdefines the results units of the measurement as NM.OZINCHdefines the results units of the measurement as OZINCH.FTLBdefines the results units of the measurement as FTLB.INCHLBdefines the results units of the measurement as INCHLB.DEGREESdefines the results units of the measurement as DEGREES.RADIANSdefines the results units of the measurement as RADIANS.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MECH:PPAirs command.
Description
- This command sets or queries the number of pole pairs for the specific measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:PPAirs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:PPAirs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:PPAirs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:PPAirs <NR1>
- MEASUrement:MEAS<x>:MECH:PPAirs?
Info
<NR1>defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MECH:PPRotation command.
Description
- This command sets or queries the specified pulses per rotation of the measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:PPRotation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:PPRotation?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:PPRotation valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:PPRotation <NR1>
- MEASUrement:MEAS<x>:MECH:PPRotation?
Info
MEAS<x>specifies the measurement number.<NR1>defines the pulses per rotation of the measurement in the range of 1 to 10000.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MECH:STYPe command.
Description
- This command sets or queries the local measurement sensor type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MECH:STYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MECH:STYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MECH:STYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MECH:STYPe {HSENSOR|QEI}
- MEASUrement:MEAS<x>:MECH:STYPe?
Info
MEAS<x>specifies the measurement number.HSENSORspecifies the sensor type as HSENSOR.QEIspecifies the sensor type as QEI.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:MINCycle command.
Description
- This command sets or queries the minimum cycle value for the DDRTERRN and DDRTERRMN measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:MINCycle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:MINCycle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:MINCycle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:MINCycle <NR1>
- MEASUrement:MEAS<x>:MINCycle?
Info
MEAS<x>specifies the measurement number.<NR1>is the minimum cycle range limit value in the range or 2 to 50.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:ODDEVen command.
Description
- This command sets or queries harmonics oddeven.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:ODDEVen?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:ODDEVen?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:ODDEVen valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:ODDEVen {ALL|EVEN|ODD}
- MEASUrement:MEAS<x>:ODDEVen?
Info
MEAS<x>specifies the measurement number.ALLdisplays all the results.EVENdisplays the even results.ODDdisplays the odd results.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:OFILters command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.lowpass: TheMEASUrement:MEAS<x>:OFILters:LOWPasscommand tree.
property
¶
lowpass: MeasurementMeasItemOfiltersLowpass
Return the MEASUrement:MEAS<x>:OFILters:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.freq: TheMEASUrement:MEAS<x>:OFILters:LOWPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:OFILters:LOWPass:SPECcommand.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:OFILters:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.freq: TheMEASUrement:MEAS<x>:OFILters:LOWPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:OFILters:LOWPass:SPECcommand.
property
¶
Return the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ command.
Description
- This command sets or returns the cut-off frequency value for a measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the cut-off frequency value for a measurement.
property
¶
Return the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC command.
Description
- This command sets or returns low pass filter specification for a measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies the low pass filter specification as none.FIRSTspecifies the low pass filter specification set to 1st Order for the measurement.SECONDspecifies the low pass filter specification set to 2nd Order for the measurement.THIRDspecifies the low pass filter specification set to 3rd Order for the measurement.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ command.
Description
- This command sets or returns the cut-off frequency value for a measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the cut-off frequency value for a measurement.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC command.
Description
- This command sets or returns low pass filter specification for a measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OFILters:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies the low pass filter specification as none.FIRSTspecifies the low pass filter specification set to 1st Order for the measurement.SECONDspecifies the low pass filter specification set to 2nd Order for the measurement.THIRDspecifies the low pass filter specification set to 3rd Order for the measurement.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:OSANgle command.
Description
- This command sets or queries the specified measurement Offset angle.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OSANgle?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OSANgle?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OSANgle valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OSANgle <NR1>
- MEASUrement:MEAS<x>:OSANgle?
Info
MEAS<x>specifies the measurement number.<NR1>specifies the offset angle of the measurement in the range or -360 to 360.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:OUTEDGEQUALifier command.
Description
- This command sets or queries local output edge qualifier source.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTEDGEQUALifier?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTEDGEQUALifier?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTEDGEQUALifier valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTEDGEQUALifier {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:OUTEDGEQUALifier?
Info
MEAS<x>specifies the measurement number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:OUTFILTers command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.lowpass: TheMEASUrement:MEAS<x>:OUTFILTers:LOWPasscommand tree.
property
¶
lowpass: MeasurementMeasItemOutfiltersLowpass
Return the MEASUrement:MEAS<x>:OUTFILTers:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.freq: TheMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPECcommand.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:OUTFILTers:LOWPass command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.freq: TheMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQcommand..spec: TheMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPECcommand.
property
¶
Return the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ command.
Description
- This command sets or queries the measurement output low pass filter frequency cutoff frequency on the scope.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ <NR2>
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR2>specifies the values for the output filter cutoff frequency. The argument range is 20 Hz to 10e6 Hz.
property
¶
Return the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC command.
Description
- This command sets or queries the measurement output low pass filter specification filter order on the scope. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies the filter order none.FIRSTspecifies the filter order first.SECONDspecifies the filter order second.THIRDspecifies the filter order third.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ command.
Description
- This command sets or queries the measurement output low pass filter frequency cutoff frequency on the scope.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ <NR2>
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?
Info
MEAS<x>specifies the measurement number.<NR2>specifies the values for the output filter cutoff frequency. The argument range is 20 Hz to 10e6 Hz.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC command.
Description
- This command sets or queries the measurement output low pass filter specification filter order on the scope. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?
Info
MEAS<x>specifies the measurement number.NONEspecifies the filter order none.FIRSTspecifies the filter order first.SECONDspecifies the filter order second.THIRDspecifies the filter order third.
Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:OUTPUT<n>VOLTage command.
Description
- Sets or queries the voltage level for the specified output voltage source n.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:OUTPUT<n>VOLTage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:OUTPUT<n>VOLTage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:OUTPUT<n>VOLTage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:OUTPUT<n>VOLTage <NR2>
- MEASUrement:MEAS<x>:OUTPUT<n>VOLTage?
Info
MEAS<x>specifies the measurement number.<NR2>is the output voltage for source n, in the range of -61 V to +61 V.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PASSFAILENabled command.
Description
- This command returns or sets the pass/fail test enable status. If enabled, this will turn on pass fail testing for the specified measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILENabled?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILENabled?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILENabled valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?
Info
<NR1>enables or disables pass fail testing for the specified measurement. A value of 1 enables and a value of 0 disables.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.
Description
- This command returns or sets the high limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILHIGHlimit?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILHIGHlimit?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILHIGHlimit valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?
Info
<NR2>sets the high limit for a measurement test. The high limit is a number which a measurement result will be tested against.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PASSFAILLIMit command.
Description
- This command returns or sets the limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILLIMit?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILLIMit?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILLIMit valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?
Info
<NR2>sets the limit for a measurement test. The limit is a number which a measurement result will be tested against.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PASSFAILLOWlimit command.
Description
- This command returns or sets the low limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILLOWlimit?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILLOWlimit?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILLOWlimit valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?
Info
<NR2>sets the low limit for a measurement test. The limit is a number which a measurement result will be tested against.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PASSFAILMARgin command.
Description
- This command returns or sets the allowed margin for limit comparisons for all pass/fail checks. This is given as a percentage with a default value of 0.05 representing 5%. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILMARgin?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILMARgin?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILMARgin valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?
Info
<NR2>sets the allowed margin for limit comparisons for all pass/fail checks. The margin as a percentage of the limit.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PASSFAILWHEN command.
Description
- This command sets or returns the condition on which a measurement test fails. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PASSFAILWHEN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PASSFAILWHEN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PASSFAILWHEN valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?
Info
LESSthansets the condition for measurement test failure as less than the given limit. This is the default value.GREATERthansets the condition for measurement test failure as greater than the given limit.Equalssets the condition for measurement test failure as equals the given limit.NOTEQualssets the condition for measurement test failure as not equal to the given limit.INSIDErangesets the condition for measurement test failure as inside the limit range.OUTSIDErangesets the condition for measurement test failure as outside the limit range.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PATTERNDETECTION command.
Description
- This command sets or queries the pattern detection type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PATTERNDETECTION?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PATTERNDETECTION?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PATTERNDETECTION valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PATTERNDETECTION {AUTO|MANUAL}
- MEASUrement:MEAS<x>:PATTERNDETECTION?
Info
MEAS<x>specifies the measurement number.AUTOautomatically detects the pattern.MANUALrequires manually detecting the pattern.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PATTERNLENgth command.
Description
- This command sets or queries the pattern length for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PATTERNLENgth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PATTERNLENgth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PATTERNLENgth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PATTERNLENgth <NR3>
- MEASUrement:MEAS<x>:PATTERNLENgth?
Info
MEAS<x>specifies the measurement number.<NR3>is the pattern length.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PATTERNTYPe command.
Description
- This command sets or queries the pattern type for the measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PATTERNTYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PATTERNTYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PATTERNTYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PATTERNTYPe {REPeating|ARBitrary}
- MEASUrement:MEAS<x>:PATTERNTYPe?
Info
MEAS<x>specifies the measurement number.REPeatingspecifies a repeating pattern.ARBitraryspecifies an arbitrary pattern.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PCOUNt command.
Description
- This command sets or returns number of pulses. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PCOUNt?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PCOUNt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PCOUNt valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PCOUNt <NR3>
- MEASUrement:MEAS<x>:PCOUNt?
Info
MEAS<x>specifies the measurement number.<NR3>is the number of pulses.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:PERFREQ command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PERFREQ?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PERFREQ?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.edge: TheMEASUrement:MEAS<x>:PERFREQ:EDGEcommand.
property
¶
Return the MEASUrement:MEAS<x>:PERFREQ:EDGE command.
Description
- This command sets or queries the edge type of a Period/Frequency measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:PERFREQ:EDGE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
Info
MEAS<x>specifies the measurement number.FIRSTcomputes the measurement between Rising edges if the first edge is Rising. Computes the measurement between Falling edges if the first edge is Falling.RISEcomputes the measurement between Rising edges.FALLcomputes the measurement between Falling edges.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:PERFREQ:EDGE command.
Description
- This command sets or queries the edge type of a Period/Frequency measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:PERFREQ:EDGE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
Info
MEAS<x>specifies the measurement number.FIRSTcomputes the measurement between Rising edges if the first edge is Rising. Computes the measurement between Falling edges if the first edge is Falling.RISEcomputes the measurement between Rising edges.FALLcomputes the measurement between Falling edges.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:POLarity command.
Description
- This command sets or queries the polarity for the measurement when the measurement type is burst width. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POLarity?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POLarity?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POLarity valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?
Info
MEAS<x>specifies the measurement number.NORMalspecifies normal polarity.INVertedspecifies inverted polarity.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:POPUlation command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.global: TheMEASUrement:MEAS<x>:POPUlation:GLOBalcommand..limit: TheMEASUrement:MEAS<x>:POPUlation:LIMITcommand tree.
property
¶
global_: MeasurementMeasItemPopulationGlobal
Return the MEASUrement:MEAS<x>:POPUlation:GLOBal command.
Description
- This command sets or queries the population settings global flag. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POPUlation:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POPUlation:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFspecifies that population settings can be changed independently for each individual measurement.ONapplies the global population settings to all the measurements’ population settings.0specifies that population settings can be changed independently for each individual measurement.1applies the global population settings to all the measurements’ population settings.
property
¶
Return the MEASUrement:MEAS<x>:POPUlation:LIMIT command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.state: TheMEASUrement:MEAS<x>:POPUlation:LIMIT:STATEcommand..value: TheMEASUrement:MEAS<x>:POPUlation:LIMIT:VALuecommand.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:POPUlation:GLOBal command.
Description
- This command sets or queries the population settings global flag. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:GLOBal?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:GLOBal?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POPUlation:GLOBal valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POPUlation:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:GLOBal?
Info
MEAS<x>specifies the measurement number.OFFspecifies that population settings can be changed independently for each individual measurement.ONapplies the global population settings to all the measurements’ population settings.0specifies that population settings can be changed independently for each individual measurement.1applies the global population settings to all the measurements’ population settings.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:POPUlation:LIMIT command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.state: TheMEASUrement:MEAS<x>:POPUlation:LIMIT:STATEcommand..value: TheMEASUrement:MEAS<x>:POPUlation:LIMIT:VALuecommand.
property
¶
Return the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE command.
Description
- This command sets or queries the population limit state for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?
Info
MEAS<x>specifies the measurement number.OFFturns off the population limit.ONturns on the population limit.0turns off the population limit.1turns on the population limit.
property
¶
Return the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue command.
Description
- This command sets or queries the population limit value for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:VALue valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue <NR3>
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?
Info
MEAS<x>specifies the measurement number.<NR3>the current limit value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE command.
Description
- This command sets or queries the population limit state for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?
Info
MEAS<x>specifies the measurement number.OFFturns off the population limit.ONturns on the population limit.0turns off the population limit.1turns on the population limit.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue command.
Description
- This command sets or queries the population limit value for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POPUlation:LIMIT:VALue valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue <NR3>
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?
Info
MEAS<x>specifies the measurement number.<NR3>the current limit value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:POWERFACtor command.
Description
- This command sets or queries the power factor value for IEC-Class C type harmonics standard. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:POWERFACtor?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:POWERFACtor?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:POWERFACtor valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:POWERFACtor <NR2>
- MEASUrement:MEAS<x>:POWERFACtor?
Info
MEAS<x>specifies the measurement number.<NR2>specifies the power factor value for class C harmonics standard.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PREGion command.
Description
- This command sets or returns pulse region for a measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PREGion?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PREGion?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PREGion valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PREGion {FPULse|SPULse|MPULse}
- MEASUrement:MEAS<x>:PREGion?
Info
FPULseis the pulse region as Fpulse.SPULseis the pulse region as Spulse.MPULseis the pulse region as Mpulse.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:PWIDth command.
Description
- This command sets or returns pulse width. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:PWIDth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:PWIDth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:PWIDth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:PWIDth <NR3>
- MEASUrement:MEAS<x>:PWIDth?
Info
<NR3>specifies the pulse width.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REDGe command.
Description
- This command turns on or off the Refine edge on qualifier. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REDGe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REDGe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REDGe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REDGe {ON|OFF}
- MEASUrement:MEAS<x>:REDGe?
Info
ONspecifies the Refine edge settings has been turned on.OFFspecifies the Refine edge settings has been turned off.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.absolute: TheMEASUrement:MEAS<x>:REFLevels:ABSolutecommand tree.
property
¶
absolute: MeasurementMeasItemReflevelsAbsolute
Return the MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.fallhigh: TheMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHighcommand.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1 command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.absolute: TheMEASUrement:MEAS<x>:REFLevels1:ABSolutecommand tree..basetop: TheMEASUrement:MEAS<x>:REFLevels1:BASETopcommand..method: TheMEASUrement:MEAS<x>:REFLevels1:METHodcommand..percent: TheMEASUrement:MEAS<x>:REFLevels1:PERCentcommand tree.
property
¶
absolute: MeasurementMeasItemReflevels1Absolute
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.falllow: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHighcommand..riselow: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELowcommand..risemid: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMidcommand..type: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPEcommand.
property
¶
basetop: MeasurementMeasItemReflevels1Basetop
Return the MEASUrement:MEAS<x>:REFLevels1:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:BASETop valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?
Info
MEAS<x>specifies the measurement number.AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:METHod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?
Info
MEAS<x>specifies the measurement number.PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:MEAS<x>:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:MEAS<x>:REFLevel:ABSolutecommands. This method is useful when precise values are required.
property
¶
percent: MeasurementMeasItemReflevels1Percent
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Sub-properties
.fallhigh: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHighcommand..falllow: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLowcommand..fallmid: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHighcommand..riselow: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELowcommand..risemid: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMidcommand..type: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPEcommand.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.falllow: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHighcommand..riselow: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELowcommand..risemid: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMidcommand..type: TheMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPEcommand.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?
Info
MEAS<x>specifies the measurement number.<NR3>is the low reference level in volts. The default is 0.0 V.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?
Info
MEAS<x>specifies the measurement number.<NR3>is the mid reference level in volts. The default is 0.0 V.
property
¶
hysteresis: MeasurementMeasItemReflevels1AbsoluteHysteresis
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?
Info
MEAS<x>specifies the measurement number.<NR3>is the hysteresis value used for autoset.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the high reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?
Info
MEAS<x>specifies the measurement number.<NR3>is the low reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?
Info
MEAS<x>specifies the measurement number.<NR3>is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?
Info
MEAS<x>specifies the measurement number.SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?
Info
MEAS<x>specifies the measurement number.<NR3>is the low reference level in volts. The default is 0.0 V.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?
Info
MEAS<x>specifies the measurement number.<NR3>is the mid reference level in volts. The default is 0.0 V.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?
Info
MEAS<x>specifies the measurement number.<NR3>is the hysteresis value used for autoset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the high reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?
Info
MEAS<x>specifies the measurement number.<NR3>is the low reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?
Info
MEAS<x>specifies the measurement number.<NR3>is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?
Info
MEAS<x>specifies the measurement number.SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:BASETop valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?
Info
MEAS<x>specifies the measurement number.AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:METHod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:METHod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?
Info
MEAS<x>specifies the measurement number.PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:MEAS<x>:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:MEAS<x>:REFLevel:ABSolutecommands. This method is useful when precise values are required.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.fallhigh: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHighcommand..falllow: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLowcommand..fallmid: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHighcommand..riselow: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELowcommand..risemid: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMidcommand..type: TheMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPEcommand.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the high reference level.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level.
property
¶
hysteresis: MeasurementMeasItemReflevels1PercentHysteresis
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?
Info
MEAS<x>specifies the measurement number.<NR3>is the hysteresis value used for the autoset.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?
Info
MEAS<x>specifies the measurement number.<NR3>the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.
Description
- This command specifies or queries the reference level percent type for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?
Info
MEAS<x>specifies the measurement number.TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the high reference level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 50% is equal to MID) used to calculate the mid reference level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?
Info
MEAS<x>specifies the measurement number.<NR3>is the hysteresis value used for the autoset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?
Info
MEAS<x>specifies the measurement number.<NR3>is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?
Info
MEAS<x>specifies the measurement number.<NR3>the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.
Description
- This command specifies or queries the reference level percent type for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?
Info
MEAS<x>specifies the measurement number.TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.fallhigh: TheMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHighcommand.
property
¶
Return the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the high reference level in volts. The default is 0.0 V.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?
Info
MEAS<x>specifies the measurement number.<NR3>is the high reference level in volts. The default is 0.0 V.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFMode command.
Description
- This command sets or queries the reference level mode for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFMode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFMode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFMode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?
Info
MEAS<x>specifies the measurement number.AUTOsets the reference level for the measurement automatically.MANualallows the user to set the reference level for the measurement.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFVoltage command.
Description
- This command sets or queries the reference voltage value for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFVoltage?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFVoltage?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFVoltage valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?
Info
MEAS<x>is the measurement number.<NR3>is the reference voltage value for the selected configuration.
Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:REFVOLTAGE<n>Val command.
Description
- Sets or queries the reference voltage per rail of Overshoot and Undershoot measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:REFVOLTAGE<n>Val?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:REFVOLTAGE<n>Val?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:REFVOLTAGE<n>Val valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:REFVOLTAGE<n>Val <NR2>
- MEASUrement:MEAS<x>:REFVOLTAGE<n>Val?
Info
MEAS<x>is the measurement number.<n>is the rail number.<NR2>is the reference voltage, in the range of -500 V to +500 V.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.allacqs: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqscommand tree..currentacq: TheMEASUrement:MEAS<x>:RESUlts:CURRentacqcommand tree..history: TheMEASUrement:MEAS<x>:RESUlts:HISTorycommand tree.
property
¶
allacqs: MeasurementMeasItemResultsAllacqs
Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.maximum: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEANcommand..minimum: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PKcommand..population: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDevcommand.
property
¶
currentacq: MeasurementMeasItemResultsCurrentacq
Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.maximum: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:MEANcommand..minimum: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PKcommand..population: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDevcommand.
property
¶
history: MeasurementMeasItemResultsHistory
Return the MEASUrement:MEAS<x>:RESUlts:HISTory command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.maximum: TheMEASUrement:MEAS<x>:RESUlts:HISTory:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:RESUlts:HISTory:MEANcommand..minimum: TheMEASUrement:MEAS<x>:RESUlts:HISTory:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:RESUlts:HISTory:PK2PKcommand..population: TheMEASUrement:MEAS<x>:RESUlts:HISTory:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:RESUlts:HISTory:STDDevcommand.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.maximum: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEANcommand..minimum: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PKcommand..population: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDevcommand.
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.
Description
- This query-only command returns the maximum value for all accumulated measurement acquisitions of the specified measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.
Description
- This query-only command returns the mean value for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.
Description
- This query-only command returns the minimum value for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.
Description
- This query-only command returns the peak-to-peak value for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?
property
¶
population: MeasurementMeasItemResultsAllacqsPopulation
Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.
Description
- This query-only command returns the population measurement value for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.
Description
- This query-only command returns the standard deviation for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.
Description
- This query-only command returns the maximum value for all accumulated measurement acquisitions of the specified measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.
Description
- This query-only command returns the mean value for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.
Description
- This query-only command returns the minimum value for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.
Description
- This query-only command returns the peak-to-peak value for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.
Description
- This query-only command returns the population measurement value for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.
Description
- This query-only command returns the standard deviation for all accumulated measurement
acquisitions for measurement
.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.maximum: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:MEANcommand..minimum: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PKcommand..population: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDevcommand.
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.
Description
- This query-only command returns the maximum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.
Description
- This query-only command returns the mean value for the measurement for the current acquisition.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.
Description
- This query-only command returns the minimum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.
Description
- This query-only command returns the peak-to-peak value for the specified measurement for the current acquisition. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?
property
¶
population: MeasurementMeasItemResultsCurrentacqPopulation
Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.
Description
- This query-only command returns the population for the specified measurement for the current acquisition. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.
Description
- This query-only command returns the standard deviation for the specified measurement for all acquisitions accumulated since statistics were last reset. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.
Description
- This query-only command returns the maximum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.
Description
- This query-only command returns the mean value for the measurement for the current acquisition.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.
Description
- This query-only command returns the minimum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.
Description
- This query-only command returns the peak-to-peak value for the specified measurement for the current acquisition. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.
Description
- This query-only command returns the population for the specified measurement for the current acquisition. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.
Description
- This query-only command returns the standard deviation for the specified measurement for all acquisitions accumulated since statistics were last reset. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:HISTory command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.maximum: TheMEASUrement:MEAS<x>:RESUlts:HISTory:MAXimumcommand..mean: TheMEASUrement:MEAS<x>:RESUlts:HISTory:MEANcommand..minimum: TheMEASUrement:MEAS<x>:RESUlts:HISTory:MINimumcommand..pk2pk: TheMEASUrement:MEAS<x>:RESUlts:HISTory:PK2PKcommand..population: TheMEASUrement:MEAS<x>:RESUlts:HISTory:POPUlationcommand..stddev: TheMEASUrement:MEAS<x>:RESUlts:HISTory:STDDevcommand.
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum command.
Description
- This query-only command returns the maximum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN command.
Description
- This query-only command returns the mean value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum command.
Description
- This query-only command returns the minimum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK command.
Description
- This query-only command returns the peak-to-peak value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?
property
¶
population: MeasurementMeasItemResultsHistoryPopulation
Return the MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation command.
Description
- This query-only command returns the population value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?
property
¶
Return the MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev command.
Description
- This query-only command returns the standard deviation value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum command.
Description
- This query-only command returns the maximum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN command.
Description
- This query-only command returns the mean value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum command.
Description
- This query-only command returns the minimum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK command.
Description
- This query-only command returns the peak-to-peak value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation command.
Description
- This query-only command returns the population value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev command.
Description
- This query-only command returns the standard deviation value for the specified measurement for each acquisition in the history. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?
Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val command.
Description
- Sets or queries the ripple frequency per specified rail for Ripple measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:RIPPLEFREQ<n>Val?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:RIPPLEFREQ<n>Val?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:RIPPLEFREQ<n>Val valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val <NR3>
- MEASUrement:MEAS<x>:RIPPLEFREQ<n>Val?
Info
MEAS<x>is the measurement number.<n>is the rail number.<NR3>is the frequency, in the range of 1 Hz to 4 GHz.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SEQuence command.
Description
- This command sets or queries the sequence of hall edges. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SEQuence?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SEQuence?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SEQuence valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SEQuence {ABC|ACB}
- MEASUrement:MEAS<x>:SEQuence?
Info
MEAS<x>specifies the measurement number.ABCspecifies the motor Hall edges sequence as ABC.ACBspecifies the motor Hall edges sequence as ACB.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SIGNALFREQUEncy command.
Description
- This command sets or queries line frequency for Harmonics and Ripple line frequency. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SIGNALFREQUEncy?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SIGNALFREQUEncy?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SIGNALFREQUEncy valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SIGNALFREQUEncy {AUTO|FIFTYHZ|SIXTYHZ|FOURHUNDREDHZ|CUSTOM}
- MEASUrement:MEAS<x>:SIGNALFREQUEncy?
Info
MEAS<x>specifies the measurement number.AUTOspecifies the line frequency as auto. Only available for Harmonics line frequency.FIFTYHZspecifies the line frequency as 50 Hz.SIXTYHZspecifies the line frequency as 60 Hz.FOURHUNDREDHZspecifies the line frequency as 400 Hz. .CUSTOMspecifies the line frequency as custom.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SIGNALType command.
Description
- This command sets or queries the signal type of source 1 for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SIGNALType?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SIGNALType?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SIGNALType valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?
Info
MEAS<x>specifies the measurement number.CLOCKspecifies a clock signal type.DATAspecifies a data signal type.AUTOautomatically selects the signal type.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SLABs command.
Description
- This command sets or returns the value for the start level in absolute.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SLABs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SLABs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SLABs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SLABs <NR3>
- MEASUrement:MEAS<x>:SLABs?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the start level in absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SLPCt command.
Description
- This command sets or returns the value for the start level in percentage.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SLPCt?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SLPCt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SLPCt valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SLPCt <NR3>
- MEASUrement:MEAS<x>:SLPCt?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the start level in percentage.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SLTYpe command.
Description
- This command sets or returns the start level source type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SLTYpe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SLTYpe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SLTYpe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:SLTYpe?
Info
MEAS<x>specifies the measurement number.VDSspecifies the start level source type as VDS.IDspecifies the start level source type as ID.VGEspecifies the start level source type as VGE.VCEspecifies the start level source type as VCE.ICspecifies the start level source type as IC.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:SMOOTHINGFILTER command.
Description
- This command sets or queries the status of smoothing filter.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:SMOOTHINGFILTER valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SMOOTHINGFILTER <NR1>
Info
MEAS<x>specifies the measurement number.<NR1>sets the value to 1 or 0. 1 enables smoothing filter and 0 disables it.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SOURCE command.
Description
- This command sets or queries local input source.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SOURCE?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SOURCE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SOURCE valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SOURCE {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOURCE?
Info
MEAS<x>specifies the measurement number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SOUrce1 command.
Description
- This command sets or queries the measurement source. The measurement number and source are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SOUrce1?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SOUrce1?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SOUrce1 valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SOUrce1 {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOUrce1?
Info
MEAS<x>specifies the measurement number.1specifies the source number.S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source.Math<x>specifies a math waveform as the source.REF<x>specifies a reference waveform as the source.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:SSC command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SSC?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SSC?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.nominalfreq: TheMEASUrement:MEAS<x>:SSC:NOMinalfreqcommand.
property
¶
nominalfreq: MeasurementMeasItemSscNominalfreq
Return the MEASUrement:MEAS<x>:SSC:NOMinalfreq command.
Description
- This command sets or queries the user-defined frequency for the measurement when the measurement type is SSC. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SSC:NOMinalfreq <NR3>
- MEASUrement:MEAS<x>:SSC:NOMinalfreq?
Info
MEAS<x>specifies the measurement number.<NR3>is the user-defined nominal frequency type for SSC configurations.
Sub-properties
.selectiontype: TheMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtypecommand.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SSC:NOMinalfreq command.
Description
- This command sets or queries the user-defined frequency for the measurement when the measurement type is SSC. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SSC:NOMinalfreq <NR3>
- MEASUrement:MEAS<x>:SSC:NOMinalfreq?
Info
MEAS<x>specifies the measurement number.<NR3>is the user-defined nominal frequency type for SSC configurations.
Properties
.selectiontype: TheMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtypecommand.
property
¶
selectiontype: MeasurementMeasItemSscNominalfreqSelectiontype
Return the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.
Description
- This command sets or queries the frequency detection type for the measurement when the measurement type is SSC. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANual}
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?
Info
MEAS<x>specifies the measurement number.AUTOautomatically sets the detection type.MANualspecifies the manual detection type.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.
Description
- This command sets or queries the frequency detection type for the measurement when the measurement type is SSC. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANual}
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?
Info
MEAS<x>specifies the measurement number.AUTOautomatically sets the detection type.MANualspecifies the manual detection type.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:STATUS command.
Description
- This command returns the pass fail status, if applicable, for the selected measurement. Measurements are specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STATUS?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STATUS?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:STATUS?
Info
PASSspecifies that the user specified measurement limit has not been violated.FAILspecifies that the user specified measurement limit has been violated.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:STLABs command.
Description
- This command sets or returns the value for the stop level in absolute.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STLABs?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STLABs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STLABs valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STLABs <NR3>
- MEASUrement:MEAS<x>:STLABs?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the stop level in absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:STLPct command.
Description
- This command sets or returns the value for the stop level in percentage.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STLPct?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STLPct?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STLPct valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STLPct <NR3>
- MEASUrement:MEAS<x>:STLPct?
Info
MEAS<x>specifies the measurement number.<NR3>specifies the value for the stop level in percentage.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:STLTYpe command.
Description
- This command sets or returns the stop level source type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STLTYpe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STLTYpe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STLTYpe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:STLTYpe?
Info
MEAS<x>specifies the measurement number.VDSspecifies the stop level source type as VDS.IDspecifies the stop level source type as ID.VGEspecifies the stop level source type as VGE.VCEspecifies the stop level source type as VCE.ICspecifies the stop level source type as IC.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:STYPe command.
Description
- This command sets or queries the source type.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:STYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:STYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:STYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:STYPe {VOLTage|CURRent}
- MEASUrement:MEAS<x>:STYPe?
Info
MEAS<x>specifies the measurement number.VOLTagesets source type as Voltage.CURRentsets source type as Current.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:SUNits command.
Description
- This command sets or queries the speed units for the specific measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:SUNits?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:SUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:SUNits valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:SUNits {RPM|HZ}
- MEASUrement:MEAS<x>:SUNits?
Info
MEAS<x>specifies the measurement number.RPMdefines the speed measurement units as RPM.HZdefines the speed measurement units as HZ.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TCKAVG command.
Description
- This command sets or queries the average clock period value used in DDR measurements.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TCKAVG?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TCKAVG?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TCKAVG valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TCKAVG <NR3>
- MEASUrement:MEAS<x>:TCKAVG?
Info
MEAS<x>specifies the measurement number.NR3is a floating point number that represents the DDR average clock period in seconds.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TCONstant command.
Description
- This command sets or queries the measurement Torque Constant.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TCONstant?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TCONstant?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TCONstant valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TCONstant <NR1>
- MEASUrement:MEAS<x>:TCONstant?
Info
MEAS<x>specifies the measurement number.NR1specifies the current multiplier value of the measurement in the range of 0 to 100.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TIMINGMode command.
Description
- This command sets or queries the Timing mode for the specified DDR measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TIMINGMode?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TIMINGMode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TIMINGMode valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TIMINGMode {EACHCLOCKCYCLE|TWOCLOCKCYCLES}
- MEASUrement:MEAS<x>:TIMINGMode?
Info
MEAS<x>specifies the measurement number.EACHCLOCKCYCLEsets the DDR Timing Mode to use each clock cycle at a time.TWOCLOCKCYCLESsets the DDR Timing Mode to use two cycles at a time.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TMEThod command.
Description
- This command sets or queries the measurement torque method.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TMEThod?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TMEThod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TMEThod valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TMEThod {SENSOR|CURRENT}
- MEASUrement:MEAS<x>:TMEThod?
Info
MEAS<x>specifies the measurement number.SENSORspecifies the Torque Method as SENSOR.CURRENTspecifies the Torque Method as CURRENT.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TOEdge command.
Description
- This command sets or queries the ‘to edge’ type for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOEdge?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOEdge?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOEdge valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?
Info
MEAS<x>specifies the measurement number.FALLspecifies the falling edge of the waveform.RISEspecifies the rising edge of the waveform.BOTHspecifies both a rising and falling edge of the waveform.SAMEasspecifies that both edges of the waveform are the same.OPPositeasspecifies that the edges of the waveform are not the same.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.
Description
- This command sets or queries the to edge search direction for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOEDGESEARCHDIRect?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOEDGESEARCHDIRect?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOEDGESEARCHDIRect valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?
Info
MEAS<x>specifies the measurement number.FORWardspecifies a forward search to the edge.BACKWardspecifies a backward search to the edge.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:TOSYmbol command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol?query and raise an AssertionError if the returned value does not matchvalue.
Info
MEAS<x>specifies the measurement number.
Properties
.logic2source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrcecommand..logic3source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrcecommand..logic4source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrcecommand..logic5source: TheMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrcecommand..measureat: TheMEASUrement:MEAS<x>:TOSYmbol:MEASUREATcommand.
property
¶
logic2source: MeasurementMeasItemTosymbolLogic2source
Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 1 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 1 To Symbol to H (High).Lsets the logic source 1 To Symbol to L (Low).Xsets the logic source 1 To Symbol to X (Don’t care).
property
¶
logic3source: MeasurementMeasItemTosymbolLogic3source
Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 2 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 2 To Symbol to H (High).Lsets the logic source 2 To Symbol to L (Low).Xsets the logic source 2 To Symbol to X (Don’t care).
property
¶
logic4source: MeasurementMeasItemTosymbolLogic4source
Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 3 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 3 To Symbol to H (High).Lsets the logic source 3 To Symbol to L (Low).Xsets the logic source 3 To Symbol to X (Don’t care).
property
¶
logic5source: MeasurementMeasItemTosymbolLogic5source
Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 4 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 4 To Symbol to H (High).Lsets the logic source 4 To Symbol to L (Low).Xsets the logic source 4 To Symbol to X (Don’t care).
property
¶
measureat: MeasurementMeasItemTosymbolMeasureat
Return the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT command.
Description
- This command sets or queries the DDR digital measurement ToSymbol MeasureAT value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:MEASUREAT valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?
Info
MEAS<x>specifies the measurement number.Startsets the ToSymbol MeasureAT to Start.Stopsets the ToSymbol MeasureAT to Stop.ClockEdgesets the sets the ToSymbol MeasureAT to ClockEdge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 1 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 1 To Symbol to H (High).Lsets the logic source 1 To Symbol to L (Low).Xsets the logic source 1 To Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 2 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 2 To Symbol to H (High).Lsets the logic source 2 To Symbol to L (Low).Xsets the logic source 2 To Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 3 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 3 To Symbol to H (High).Lsets the logic source 3 To Symbol to L (Low).Xsets the logic source 3 To Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce command.
Description
- This command sets or queries the DDR digital measurement logic 4 source To Symbol.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?
Info
MEAS<x>specifies the measurement number.Hsets the logic source 4 To Symbol to H (High).Lsets the logic source 4 To Symbol to L (Low).Xsets the logic source 4 To Symbol to X (Don’t care).
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT command.
Description
- This command sets or queries the DDR digital measurement ToSymbol MeasureAT value.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TOSYmbol:MEASUREAT valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?
Info
MEAS<x>specifies the measurement number.Startsets the ToSymbol MeasureAT to Start.Stopsets the ToSymbol MeasureAT to Stop.ClockEdgesets the sets the ToSymbol MeasureAT to ClockEdge.
Bases: SCPICmdWrite
The MEASUrement:MEAS<x>:TRANSition command.
Description
- This command sets or queries the transition edges flag for the measurement. The measurement number is specified by x.
Usage
- Using the
.write(value)method will send theMEASUrement:MEAS<x>:TRANSition valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}
Info
<NR1>= 1, the measurement is computed on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only. If it is set to 0, the measurement is computed on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.OFFcomputes the measurement on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.ONcomputes the measurement on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:TYPe command.
Description
- This command sets or queries the measurement type for the measurement specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:TYPe?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:TYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:TYPe valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:TYPe {ACCOMMONMODE|ACRMS|AMPlITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMOVERSHOOT|DPMUNDERSHOOT|DPMRIPPLE|DPMTURNOFFTIME|DPMTURNONTIME|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HIGH|HEIGHT|HEIGHTBER|HIGHTIME|HOLD|IMDAPOWERQUALITY|IMDAHARMONICS|IMDAINPUTVOLTAGE|IMDAINPUTCURRENT|IMDAINPUTPOWER|IMDAPHASORDIAGRAM|IMDAEFFICIENCY|IMDALINERIPPLE|IMDASWITCHRIPPLE|IMDADQ0|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NPJ|NOVERSHOOT|NWIDTH|PDUTTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SRJ|SSCFREQDEV|SSCMODRATE|SETUP|SKEW|TIE|TIMEOUTSIDELEVEL|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WIDTH|WIDTHBER}
- MEASUrement:MEAS<x>:TYPe?
Info
ACCOMMONMODEAC Common Mode (Pk-Pk) is the peak-to-peak of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.ACRMS(AC RMS) is the true Root Mean Square of the data points, about the Mean. This measurement can be made across the entire record, or on each cycle in the record.AMPLITUDEis the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.Amplitude = High - LowAREAis the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.BASEis the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.BITAMPLITUDE(Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITHIGH(Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BITLOW(Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.BURSTWIDTH(Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.COMMONMODE(DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DATARATE(Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.DCD(duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDJ(data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DDRAOS(area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.DDRAOSPERTCK(area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAOSPERUI(area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRAUS(area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.DDRAUSPERTCK(area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.DDRAUSPERUI(area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.DDRHOLDDIFF(hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.DDRSETUPDIFF(setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.DDRTCHABS(absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.DDRTCHAVERAGE(average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles.This measurement is made across the entire record.DDRTCKAVERAGE(average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles.This measurement is made across the entire record.DDRTCLABS(absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.DDRTCLAVERAGE(average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.DDRTERRMN(cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).DDRTERRN(cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).DDRTJITCC(cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.DDRTJITDUTY(half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.DDRTJITPER(clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.DDRTPST(read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.DDRTRPRE(read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRTWPREis the width of the Write burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.DDRVIXACis the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.DDRTDQSCKis the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.DELayis the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.DJ(deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DJDIRAC(dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.DPMOVERSHOOTis the difference between Maximum and Top, divided by the amplitude. This measurement can be made across the entire record or on each cycle in the record at the specified reference voltage.DPMUNDERSHOOTis the difference between Minimum and Base, divided by the amplitude. This measurement can be made across the entire record or on each cycle in the record at the specified reference voltage.DPMRIPPLEis the RMS and peak-to-peak values of the output signal on the DC Rail.DPMTURNOFFTIMEis the time delay between load current going low to other rail outputs going low during power down.DPMTURNONTIMEis the time delay between load current going high to other rail outputs going high during power on.EYEHIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.EYELOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.FALLSLEWRATE(Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.FALLTIME(Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.FREQuencyis the reciprocal of Period. This measurement is made on each cycle in the record.F2is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F4is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.F8is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGH(Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.HEIGHT(Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HEIGHTBER(Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.HIGHTIME(High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.HOLD(Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.IMDAPOWERQUALITY(Power Quality) measures the Frequency and RMS values of the voltage and current, Crest Factors of the voltage and current, True Power (PTRUE), Reactive Power (PRE), Apparent Power (PAPP), Power Factor, and Phase Angle (θ) of the AC signal.IMDAHARMONICS(Harmonics) plots the signal amplitude at the fundamental line frequency and its harmonics and measures the RMS amplitude and Total Harmonic Distortion of the signal.IMDAINPUTVOLTAGE(Input Voltage) measures the RMS value of the Input Voltages. The number of voltages can vary with wiring configuration.IMDAINPUTCURRENT(Input Current) measures the RMS value of the Input Currents. The number of currents can vary with wiring configuration.IMDAINPUTPOWER(Input Power) measures the RMS value of the Input Power. The power waveforms are shown as derived MATH waveforms, which are respective pairs of Input Voltage \* Current waveforms.IMDAPHASORDIAGRAM(Phasor Diagram) represents magnitudes and phase angles between voltage(s) and current(s) per winding pair.IMDAEFFICIENCY(Efficiency) measures the ratio of sum of output power(s) to input power for respective input and output Voltage and Current pairs. Note: the current release cannot support 3V and 3I pairs, since this requires 12 channels. We restrict to 2V and 2I which needs 8 scope channels.IMDALINERIPPLE(Line Ripple) provides the RMS and peak-to-peak measurements of the line frequency portion of the respective AC Voltage or Current signals.IMDASWITCHINGRIPPLE(Switching Ripple) provides the RMS and peak-to-peak measurements of the respective Voltage or Current signals.IMDADQ0measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0.JITTERSUMMARY(Jitter Summary) is a group consisting of the following measurements: TIE, TJ@BER, Eye Width@BER, Eye Height@BER, RJ-δδ, DJ-δδ, PJ, DDJ, DcD, F/2, F/4, F/8. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J2is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.J9is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.LOW(Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.LOWTIME(Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.MAXimumis the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.MEANis the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.MINImumis the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.NDUty(Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.Negative Duty Cycle = (Negative Width) / Period × 100%NPERIOD(Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.NPJ(non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.NOVershoot(Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Negative Overshoot = (Base - Minimum) / Amplitude × 100%)NWIdth(Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.PDUTY(Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.Positive Duty Cycle = (Positive Width)/Period × 100%PERIODis the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.PHASEis the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.PHASENOISE(Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.PJ(periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.PK2Pk(Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.POVERSHOOT(Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.Positive Overshoot = (Maximum - Top) / Amplitude ×100%PWIDTH(Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.QFACTOR(Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RISESLEWRATE(Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RISETIMERise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.RJ(random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RJDIRAC(dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.RMSis the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.SRJ(sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCFREQDEV(SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SSCMODRATE(SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.SETUP(Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.SKEWSkew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.TIE(time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.TIMEOUTSIDELEVELTime Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.TJBER(total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TNTRATIOT/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.TOPis the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.UNITINTERVAL(Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.VDIFFXOVR(Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTH(Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.WIDTHBER(Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:WAITTime command.
Description
- Sets or queries the wait time.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:WAITTime?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:WAITTime?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:WAITTime valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:WAITTime <NR2>
- MEASUrement:MEAS<x>:WAITTime?
Info
MEAS<x>is the measurement number.<NR2>is the wait time, in the range of 1 s to 500 s.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEAS<x>:WINDOWLENgth command.
Description
- This command sets or queries the window length for the measurement. The measurement number is specified by x.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:WINDOWLENgth?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:WINDOWLENgth?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEAS<x>:WINDOWLENgth valuecommand.
SCPI Syntax
- MEASUrement:MEAS<x>:WINDOWLENgth <NR3>
- MEASUrement:MEAS<x>:WINDOWLENgth?
Info
<NR3>is the value for the window length.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:XUNIT command.
Description
- Returns the horizontal scale units of the specified measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:XUNIT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:XUNIT?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:XUNIT?
Info
MEAS<x>specifies the measurement number.
Bases: SCPICmdRead
The MEASUrement:MEAS<x>:YUNIT command.
Description
- Returns the vertical scale units of the specified measurement.
Usage
- Using the
.query()method will send theMEASUrement:MEAS<x>:YUNIT?query. - Using the
.verify(value)method will send theMEASUrement:MEAS<x>:YUNIT?query and raise an AssertionError if the returned value does not matchvalue.
SCPI Syntax
- MEASUrement:MEAS<x>:YUNIT?
Info
MEAS<x>specifies the measurement number.
Bases: SCPICmdRead
The MEASUrement:MEASRange command tree.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.max: TheMEASUrement:MEASRange:MAXcommand..min: TheMEASUrement:MEASRange:MINcommand..state: TheMEASUrement:MEASRange:STATEcommand.
property
¶
Return the MEASUrement:MEASRange:MAX command.
Description
- This command sets or queries the global range maximum value.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange:MAX?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange:MAX?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEASRange:MAX valuecommand.
SCPI Syntax
- MEASUrement:MEASRange:MAX <NR3>
- MEASUrement:MEASRange:MAX?
Info
MEAS<x>specifies the measurement number.<NR3>is the maximum measurement range limit value.
property
¶
Return the MEASUrement:MEASRange:MIN command.
Description
- This command sets or queries the global range minimum value.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange:MIN?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange:MIN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEASRange:MIN valuecommand.
SCPI Syntax
- MEASUrement:MEASRange:MIN <NR3>
- MEASUrement:MEASRange:MIN?
Info
MEAS<x>specifies the measurement number.<NR3>is the minimum measurement range limit value.
property
¶
state: MeasurementMeasrangeState
Return the MEASUrement:MEASRange:STATE command.
Description
- This command sets or queries the global range state.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEASRange:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEASRange:STATE?
Info
MEAS<x>specifies the measurement number.OFFspecifies that the measurement results are not limited.ONspecifies that the measurement results are limited to results with values between the range minimum and maximum.0specifies that the measurement results are not limited.1specifies that the measurement results are limited to results with values between the range minimum and maximum.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEASRange:MAX command.
Description
- This command sets or queries the global range maximum value.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange:MAX?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange:MAX?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEASRange:MAX valuecommand.
SCPI Syntax
- MEASUrement:MEASRange:MAX <NR3>
- MEASUrement:MEASRange:MAX?
Info
MEAS<x>specifies the measurement number.<NR3>is the maximum measurement range limit value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEASRange:MIN command.
Description
- This command sets or queries the global range minimum value.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange:MIN?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange:MIN?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEASRange:MIN valuecommand.
SCPI Syntax
- MEASUrement:MEASRange:MIN <NR3>
- MEASUrement:MEASRange:MIN?
Info
MEAS<x>specifies the measurement number.<NR3>is the minimum measurement range limit value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MEASRange:STATE command.
Description
- This command sets or queries the global range state.
Usage
- Using the
.query()method will send theMEASUrement:MEASRange:STATE?query. - Using the
.verify(value)method will send theMEASUrement:MEASRange:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MEASRange:STATE valuecommand.
SCPI Syntax
- MEASUrement:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEASRange:STATE?
Info
MEAS<x>specifies the measurement number.OFFspecifies that the measurement results are not limited.ONspecifies that the measurement results are limited to results with values between the range minimum and maximum.0specifies that the measurement results are not limited.1specifies that the measurement results are limited to results with values between the range minimum and maximum.
Bases: SCPICmdRead
The MEASUrement:MECH command tree.
Usage
- Using the
.query()method will send theMEASUrement:MECH?query. - Using the
.verify(value)method will send theMEASUrement:MECH?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.eindexz: TheMEASUrement:MECH:EINDexzcommand..gratio: TheMEASUrement:MECH:GRATiocommand..munits: TheMEASUrement:MECH:MUNitscommand..ppairs: TheMEASUrement:MECH:PPAirscommand..pprotation: TheMEASUrement:MECH:PPRotationcommand..source1: TheMEASUrement:MECH:SOUrce1command..stype: TheMEASUrement:MECH:STYPecommand.
property
¶
eindexz: MeasurementMechEindexz
Return the MEASUrement:MECH:EINDexz command.
Description
- This command sets or queries the global mechanical Index Z source.
Usage
- Using the
.query()method will send theMEASUrement:MECH:EINDexz?query. - Using the
.verify(value)method will send theMEASUrement:MECH:EINDexz?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:EINDexz valuecommand.
SCPI Syntax
- MEASUrement:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MECH:EINDexz?
Info
ONspecifies the Index Z check box state as enabled.OFFspecifies the Index Z check box state as disabled.1specifies the Index Z check box state as enabled.0specifies the Index Z check box state as disabled.
property
¶
gratio: MeasurementMechGratio
Return the MEASUrement:MECH:GRATio command.
Description
- This command sets or queries the measurement gear ratio.
Usage
- Using the
.query()method will send theMEASUrement:MECH:GRATio?query. - Using the
.verify(value)method will send theMEASUrement:MECH:GRATio?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:GRATio valuecommand.
SCPI Syntax
- MEASUrement:MECH:GRATio <NR3>
- MEASUrement:MECH:GRATio?
Info
<NR3>specifies the gear ratio value for a specified measurement. The minimum and maximum values are 0.001 to 1000.
property
¶
munits: MeasurementMechMunits
Return the MEASUrement:MECH:MUNits command.
Description
- This command sets or queries the global mechanical measurement results units.
Usage
- Using the
.query()method will send theMEASUrement:MECH:MUNits?query. - Using the
.verify(value)method will send theMEASUrement:MECH:MUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:MUNits valuecommand.
SCPI Syntax
- MEASUrement:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MECH:MUNits?
Info
NMspecifies the results units of mechanical Torque measurement as NM.OZINCHspecifies the results units of mechanical Torque measurement as OZINCH.FTLBspecifies the results units of mechanical Torque measurement as FTLB.INCHLBspecifies the results units of mechanical Torque measurement as INCHLB.DEGREESspecifies the results units of mechanical Torque measurement as DEGREES.RADIANSspecifies the results units of mechanical Torque measurement as RADIANS.
property
¶
ppairs: MeasurementMechPpairs
Return the MEASUrement:MECH:PPAirs command.
Description
- This command sets or queries the measurement number of pole pairs.
Usage
- Using the
.query()method will send theMEASUrement:MECH:PPAirs?query. - Using the
.verify(value)method will send theMEASUrement:MECH:PPAirs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:PPAirs valuecommand.
SCPI Syntax
- MEASUrement:MECH:PPAirs <NR1>
- MEASUrement:MECH:PPAirs?
Info
<NR1>defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.
property
¶
pprotation: MeasurementMechPprotation
Return the MEASUrement:MECH:PPRotation command.
Description
- This command sets or queries the global pulses per rotation of the measurement.
Usage
- Using the
.query()method will send theMEASUrement:MECH:PPRotation?query. - Using the
.verify(value)method will send theMEASUrement:MECH:PPRotation?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:PPRotation valuecommand.
SCPI Syntax
- MEASUrement:MECH:PPRotation <NR1>
- MEASUrement:MECH:PPRotation?
Info
<NR1>defines the pulses per rotation of the measurement. The minimum to maximum range is 1 to 100000.
property
¶
source1: MeasurementMechSource1
Return the MEASUrement:MECH:SOUrce1 command.
Description
- This command sets or queries the global mechanical source of the specified source number.
Usage
- Using the
.query()method will send theMEASUrement:MECH:SOUrce1?query. - Using the
.verify(value)method will send theMEASUrement:MECH:SOUrce1?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:SOUrce1 valuecommand.
SCPI Syntax
- MEASUrement:MECH:SOUrce1 {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>|CH<x>_D<x>}
- MEASUrement:MECH:SOUrce1?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source waveform.MATH<x>specifies a math waveform as the source waveform.REF<x>specifies an reference waveform as the source waveform .CH<x>_D<x>specifies a digital channel as the source waveform.
property
¶
stype: MeasurementMechStype
Return the MEASUrement:MECH:STYPe command.
Description
- This command sets or queries the measurement sensor type.
Usage
- Using the
.query()method will send theMEASUrement:MECH:STYPe?query. - Using the
.verify(value)method will send theMEASUrement:MECH:STYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:STYPe valuecommand.
SCPI Syntax
- MEASUrement:MECH:STYPe {HSENSOR|QEI}
- MEASUrement:MECH:STYPe?
Info
HSENSORspecifies the sensor type as HSENSOR.QEIspecifies the sensor type as QEI.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MECH:EINDexz command.
Description
- This command sets or queries the global mechanical Index Z source.
Usage
- Using the
.query()method will send theMEASUrement:MECH:EINDexz?query. - Using the
.verify(value)method will send theMEASUrement:MECH:EINDexz?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:EINDexz valuecommand.
SCPI Syntax
- MEASUrement:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MECH:EINDexz?
Info
ONspecifies the Index Z check box state as enabled.OFFspecifies the Index Z check box state as disabled.1specifies the Index Z check box state as enabled.0specifies the Index Z check box state as disabled.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MECH:GRATio command.
Description
- This command sets or queries the measurement gear ratio.
Usage
- Using the
.query()method will send theMEASUrement:MECH:GRATio?query. - Using the
.verify(value)method will send theMEASUrement:MECH:GRATio?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:GRATio valuecommand.
SCPI Syntax
- MEASUrement:MECH:GRATio <NR3>
- MEASUrement:MECH:GRATio?
Info
<NR3>specifies the gear ratio value for a specified measurement. The minimum and maximum values are 0.001 to 1000.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MECH:MUNits command.
Description
- This command sets or queries the global mechanical measurement results units.
Usage
- Using the
.query()method will send theMEASUrement:MECH:MUNits?query. - Using the
.verify(value)method will send theMEASUrement:MECH:MUNits?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:MUNits valuecommand.
SCPI Syntax
- MEASUrement:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MECH:MUNits?
Info
NMspecifies the results units of mechanical Torque measurement as NM.OZINCHspecifies the results units of mechanical Torque measurement as OZINCH.FTLBspecifies the results units of mechanical Torque measurement as FTLB.INCHLBspecifies the results units of mechanical Torque measurement as INCHLB.DEGREESspecifies the results units of mechanical Torque measurement as DEGREES.RADIANSspecifies the results units of mechanical Torque measurement as RADIANS.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MECH:PPAirs command.
Description
- This command sets or queries the measurement number of pole pairs.
Usage
- Using the
.query()method will send theMEASUrement:MECH:PPAirs?query. - Using the
.verify(value)method will send theMEASUrement:MECH:PPAirs?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:PPAirs valuecommand.
SCPI Syntax
- MEASUrement:MECH:PPAirs <NR1>
- MEASUrement:MECH:PPAirs?
Info
<NR1>defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MECH:PPRotation command.
Description
- This command sets or queries the global pulses per rotation of the measurement.
Usage
- Using the
.query()method will send theMEASUrement:MECH:PPRotation?query. - Using the
.verify(value)method will send theMEASUrement:MECH:PPRotation?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:PPRotation valuecommand.
SCPI Syntax
- MEASUrement:MECH:PPRotation <NR1>
- MEASUrement:MECH:PPRotation?
Info
<NR1>defines the pulses per rotation of the measurement. The minimum to maximum range is 1 to 100000.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MECH:SOUrce1 command.
Description
- This command sets or queries the global mechanical source of the specified source number.
Usage
- Using the
.query()method will send theMEASUrement:MECH:SOUrce1?query. - Using the
.verify(value)method will send theMEASUrement:MECH:SOUrce1?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:SOUrce1 valuecommand.
SCPI Syntax
- MEASUrement:MECH:SOUrce1 {S<x>_Ch<x>|CH<x>|MATH<x>|REF<x>|CH<x>_D<x>}
- MEASUrement:MECH:SOUrce1?
Info
S<x>_Ch<x>specifies the remote scope number and the analog channel as the source.CH<x>specifies an analog channel as the source waveform.MATH<x>specifies a math waveform as the source waveform.REF<x>specifies an reference waveform as the source waveform .CH<x>_D<x>specifies a digital channel as the source waveform.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MECH:STYPe command.
Description
- This command sets or queries the measurement sensor type.
Usage
- Using the
.query()method will send theMEASUrement:MECH:STYPe?query. - Using the
.verify(value)method will send theMEASUrement:MECH:STYPe?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MECH:STYPe valuecommand.
SCPI Syntax
- MEASUrement:MECH:STYPe {HSENSOR|QEI}
- MEASUrement:MECH:STYPe?
Info
HSENSORspecifies the sensor type as HSENSOR.QEIspecifies the sensor type as QEI.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:MINUI command.
Description
- This command sets or queries the minimum number of unit intervals required for BUJ analysis.
Usage
- Using the
.query()method will send theMEASUrement:MINUI?query. - Using the
.verify(value)method will send theMEASUrement:MINUI?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:MINUI valuecommand.
SCPI Syntax
- MEASUrement:MINUI <NR3>
- MEASUrement:MINUI?
Info
<NR3>is the minimum number of unit intervals required for BUJ analysis.
Bases: SCPICmdRead
The MEASUrement:POPUlation command tree.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.limit: TheMEASUrement:POPUlation:LIMITcommand tree.
property
¶
limit: MeasurementPopulationLimit
Return the MEASUrement:POPUlation:LIMIT command tree.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation:LIMIT?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation:LIMIT?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.state: TheMEASUrement:POPUlation:LIMIT:STATEcommand..value: TheMEASUrement:POPUlation:LIMIT:VALuecommand.
Bases: SCPICmdRead
The MEASUrement:POPUlation:LIMIT command tree.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation:LIMIT?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation:LIMIT?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.state: TheMEASUrement:POPUlation:LIMIT:STATEcommand..value: TheMEASUrement:POPUlation:LIMIT:VALuecommand.
property
¶
Return the MEASUrement:POPUlation:LIMIT:STATE command.
Description
- This command sets or queries the global population limit state for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation:LIMIT:STATE?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation:LIMIT:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:POPUlation:LIMIT:STATE valuecommand.
SCPI Syntax
- MEASUrement:POPUlation:LIMIT:STATE {OFF|ON|0|1 }
- MEASUrement:POPUlation:LIMIT:STATE?
Info
OFFturns off the population limit.ONturns on the population limit.0turns off the population limit.1turns on the population limit.
property
¶
Return the MEASUrement:POPUlation:LIMIT:VALue command.
Description
- This command sets or queries the global population limit value for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation:LIMIT:VALue?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation:LIMIT:VALue?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:POPUlation:LIMIT:VALue valuecommand.
SCPI Syntax
- MEASUrement:POPUlation:LIMIT:VALue <NR1>
- MEASUrement:POPUlation:LIMIT:VALue?
Info
<NR1>is the current limit value.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:POPUlation:LIMIT:STATE command.
Description
- This command sets or queries the global population limit state for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation:LIMIT:STATE?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation:LIMIT:STATE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:POPUlation:LIMIT:STATE valuecommand.
SCPI Syntax
- MEASUrement:POPUlation:LIMIT:STATE {OFF|ON|0|1 }
- MEASUrement:POPUlation:LIMIT:STATE?
Info
OFFturns off the population limit.ONturns on the population limit.0turns off the population limit.1turns on the population limit.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:POPUlation:LIMIT:VALue command.
Description
- This command sets or queries the global population limit value for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:POPUlation:LIMIT:VALue?query. - Using the
.verify(value)method will send theMEASUrement:POPUlation:LIMIT:VALue?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:POPUlation:LIMIT:VALue valuecommand.
SCPI Syntax
- MEASUrement:POPUlation:LIMIT:VALue <NR1>
- MEASUrement:POPUlation:LIMIT:VALue?
Info
<NR1>is the current limit value.
Bases: ValidatedDynamicNumberCmd, SCPICmdRead
The MEASUrement:REF<x> command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.reflevels: TheMEASUrement:REF<x>:REFLevelscommand tree.
property
¶
reflevels: MeasurementRefItemReflevels
Return the MEASUrement:REF<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.absolute: TheMEASUrement:REF<x>:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:REF<x>:REFLevels:BASETopcommand..method: TheMEASUrement:REF<x>:REFLevels:METHodcommand..percent: TheMEASUrement:REF<x>:REFLevels:PERCentcommand tree.
Bases: SCPICmdRead
The MEASUrement:REF<x>:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.absolute: TheMEASUrement:REF<x>:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:REF<x>:REFLevels:BASETopcommand..method: TheMEASUrement:REF<x>:REFLevels:METHodcommand..percent: TheMEASUrement:REF<x>:REFLevels:PERCentcommand tree.
property
¶
absolute: MeasurementRefItemReflevelsAbsolute
Return the MEASUrement:REF<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.fallhigh: TheMEASUrement:REF<x>:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:REF<x>:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:REF<x>:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:REF<x>:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:REF<x>:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:REF<x>:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:REF<x>:REFLevels:ABSolute:TYPEcommand.
property
¶
basetop: MeasurementRefItemReflevelsBasetop
Return the MEASUrement:REF<x>:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.
Usage
- Using the
.write()method will send theMEASUrement:REF<x>:REFLevels:BASETopcommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:BASETop
Info
AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
property
¶
Return the MEASUrement:REF<x>:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?
Info
PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:REF<x>:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:REF<x>:REFLevel:ABSolutecommands. This method is useful when precise values are required.
property
¶
percent: MeasurementRefItemReflevelsPercent
Return the MEASUrement:REF<x>:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.fallhigh: TheMEASUrement:REF<x>:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:REF<x>:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:REF<x>:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:REF<x>:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:REF<x>:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:REF<x>:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:REF<x>:REFLevels:PERCent:TYPEcommand.
Bases: SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.fallhigh: TheMEASUrement:REF<x>:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:REF<x>:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:REF<x>:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:REF<x>:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:REF<x>:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:REF<x>:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:REF<x>:REFLevels:ABSolute:TYPEcommand.
property
¶
Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?
Info
<NR3>is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
property
¶
Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?
Info
<NR3>is the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.
property
¶
Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?
Info
<NR3>is the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.
property
¶
hysteresis: MeasurementRefItemReflevelsAbsoluteHysteresis
Return the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?
Info
<NR3>is the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.
property
¶
Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?
Info
<NR3>is the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.
property
¶
Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?
Info
<NR3>is the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.
property
¶
Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?
Info
<NR3>is the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.
property
¶
Return the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?
Info
SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?
Info
<NR3>is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?
Info
<NR3>is the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?
Info
<NR3>is the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?
Info
<NR3>is the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?
Info
<NR3>is the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?
Info
<NR3>is the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?
Info
<NR3>is the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?
Info
SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWriteNoArguments
The MEASUrement:REF<x>:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.
Usage
- Using the
.write()method will send theMEASUrement:REF<x>:REFLevels:BASETopcommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:BASETop
Info
AUTOautomatically chooses a reference level method.MINMaxspecifies that reference levels are relative to the measurement MIN and MAX.MEANhistogramspecifies that reference levels are relative to the histogram mean BASE and TOP.MODEhistogramspecifies that reference levels are relative to the histogram mode BASE and TOP.EYEhistogramspecifies that reverence levels are relative to the eye histogram BASE and TOP.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?
Info
PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:REF<x>:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:REF<x>:REFLevel:ABSolutecommands. This method is useful when precise values are required.
Bases: SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.fallhigh: TheMEASUrement:REF<x>:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:REF<x>:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:REF<x>:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:REF<x>:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:REF<x>:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:REF<x>:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:REF<x>:REFLevels:PERCent:TYPEcommand.
property
¶
Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the falling edge.
property
¶
Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?
Info
<NR3>is the percentage used to calculate the low reference level.
property
¶
Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the falling edge.
property
¶
hysteresis: MeasurementRefItemReflevelsPercentHysteresis
Return the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?
Info
<NR3>is the percentage used to calculate the hysteresis of the reference level.
property
¶
Return the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the rising edge.
property
¶
Return the MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?
Info
<NR3>is the percentage used to calculate the low reference level of the rising edge.
property
¶
Return the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the rising edge.
property
¶
Return the MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.
Description
- This command sets or queries the reference level percent type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?
Info
TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?
Info
<NR3>is the percentage used to calculate the low reference level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?
Info
<NR3>is the percentage used to calculate the hysteresis of the reference level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?
Info
<NR3>is the percentage used to calculate the low reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.
Description
- This command sets or queries the reference level percent type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REF<x>:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REF<x>:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?
Info
TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: SCPICmdRead
The MEASUrement:REFLevels command tree.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.absolute: TheMEASUrement:REFLevels:ABSolutecommand tree..basetop: TheMEASUrement:REFLevels:BASETopcommand..jittermode: TheMEASUrement:REFLevels:JITTERMODEcommand..method: TheMEASUrement:REFLevels:METHodcommand..mode: TheMEASUrement:REFLevels:MODEcommand..percent: TheMEASUrement:REFLevels:PERCentcommand tree..type: TheMEASUrement:REFLevels:TYPEcommand.
property
¶
absolute: MeasurementReflevelsAbsolute
Return the MEASUrement:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.fallhigh: TheMEASUrement:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:REFLevels:ABSolute:TYPEcommand.
property
¶
basetop: MeasurementReflevelsBasetop
Return the MEASUrement:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:BASETop valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?
Info
AUTOsets the base top method to AUTO.MINMaxsets the base top method to MINMax.MEANhistogramsets the base top method to MEANhistogram.MODEhistogramsets the base top method to MODEhistogram.EYEhistogramsets the base top method to EYEhistogram.
property
¶
jittermode: MeasurementReflevelsJittermode
Return the MEASUrement:REFLevels:JITTERMODE command.
Description
- This command sets or queries how often reference levels are calculated on Jitter measurements. If the mode is set to Latch, ref levels are calculated only on the first acquisition after a statistics reset. If it is set to Continuous, reference levels are calculated on every acquisition.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:JITTERMODE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:JITTERMODE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:JITTERMODE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:JITTERMODE {CONTinuous|LATCh}
- MEASUrement:REFLevels:JITTERMODE?
Info
CONTinuousspecifies that reference levels are calculated on every acquisition.LATChspecifies that reference levels are calculated only on the first acquisition after a statistics reset.
property
¶
method: MeasurementReflevelsMethod
Return the MEASUrement:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?
Info
PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:REFLevels:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:REFLevels:REFLevel:ABSolutecommands. This method is useful when precise values are required.
property
¶
mode: MeasurementReflevelsMode
Return the MEASUrement:REFLevels:MODE command.
Description
- This command sets or queries how often reference levels are calculated.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:MODE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:MODE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:MODE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?
Info
LATChcalculates reference levels only on the first acquisition after a statistics reset.CONTinuouscalculates reference levels on every acquisition.
property
¶
percent: MeasurementReflevelsPercent
Return the MEASUrement:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.fallhigh: TheMEASUrement:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:REFLevels:PERCent:TYPEcommand.
property
¶
type: MeasurementReflevelsType
Return the MEASUrement:REFLevels:TYPE command.
Description
- This command sets or queries the shared reference level method used for sources of measurement calculations.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?
Info
GLOBalshares reference levels across measurements.PERSourcecauses reference levels to be used on individual measurements.
Bases: SCPICmdRead
The MEASUrement:REFLevels:ABSolute command tree.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.fallhigh: TheMEASUrement:REFLevels:ABSolute:FALLHighcommand..falllow: TheMEASUrement:REFLevels:ABSolute:FALLLowcommand..fallmid: TheMEASUrement:REFLevels:ABSolute:FALLMidcommand..hysteresis: TheMEASUrement:REFLevels:ABSolute:HYSTeresiscommand..risehigh: TheMEASUrement:REFLevels:ABSolute:RISEHighcommand..riselow: TheMEASUrement:REFLevels:ABSolute:RISELowcommand..risemid: TheMEASUrement:REFLevels:ABSolute:RISEMidcommand..type: TheMEASUrement:REFLevels:ABSolute:TYPEcommand.
property
¶
fallhigh: MeasurementReflevelsAbsoluteFallhigh
Return the MEASUrement:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?
Info
<NR3>is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
property
¶
falllow: MeasurementReflevelsAbsoluteFalllow
Return the MEASUrement:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?
Info
<NR3>is the value used as the low reference level of the falling edge.
property
¶
fallmid: MeasurementReflevelsAbsoluteFallmid
Return the MEASUrement:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?
Info
<NR3>is the value used as the mid reference level of the falling edge.
property
¶
hysteresis: MeasurementReflevelsAbsoluteHysteresis
Return the MEASUrement:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?
Info
<NR3>is the value of the hysteresis of the reference level.
property
¶
risehigh: MeasurementReflevelsAbsoluteRisehigh
Return the MEASUrement:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?
Info
<NR3>is the value used as the high reference level of the rising edge.
property
¶
riselow: MeasurementReflevelsAbsoluteRiselow
Return the MEASUrement:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?
Info
<NR3>is the value used as the the low reference level of the rising edge.
property
¶
risemid: MeasurementReflevelsAbsoluteRisemid
Return the MEASUrement:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?
Info
<NR3>is the mid reference level of the rising edge.
property
¶
Return the MEASUrement:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?
Info
SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:FALLHigh command.
Description
- This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?
Info
<NR3>is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:FALLLow command.
Description
- This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?
Info
<NR3>is the value used as the low reference level of the falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:FALLMid command.
Description
- This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?
Info
<NR3>is the value used as the mid reference level of the falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:HYSTeresis command.
Description
- This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?
Info
<NR3>is the value of the hysteresis of the reference level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:RISEHigh command.
Description
- This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?
Info
<NR3>is the value used as the high reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:RISELow command.
Description
- This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?
Info
<NR3>is the value used as the the low reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:RISEMid command.
Description
- This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?
Info
<NR3>is the mid reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:ABSolute:TYPE command.
Description
- This command sets or queries the reference level type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:ABSolute:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:ABSolute:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:ABSolute:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?
Info
SAMEspecifies that the absolute levels are set the same.UNIQuespecifies that the absolute levels can be set independently.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:BASETop command.
Description
- This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:BASETop?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:BASETop?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:BASETop valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?
Info
AUTOsets the base top method to AUTO.MINMaxsets the base top method to MINMax.MEANhistogramsets the base top method to MEANhistogram.MODEhistogramsets the base top method to MODEhistogram.EYEhistogramsets the base top method to EYEhistogram.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:JITTERMODE command.
Description
- This command sets or queries how often reference levels are calculated on Jitter measurements. If the mode is set to Latch, ref levels are calculated only on the first acquisition after a statistics reset. If it is set to Continuous, reference levels are calculated on every acquisition.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:JITTERMODE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:JITTERMODE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:JITTERMODE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:JITTERMODE {CONTinuous|LATCh}
- MEASUrement:REFLevels:JITTERMODE?
Info
CONTinuousspecifies that reference levels are calculated on every acquisition.LATChspecifies that reference levels are calculated only on the first acquisition after a statistics reset.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:METHod command.
Description
- This command sets or queries the method used to calculate reference levels for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:METHod?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:METHod?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:METHod valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?
Info
PERCentspecifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using theMEASUrement:REFLevels:REFLevel:PERCentcommands.ABSolutespecifies that the reference levels are set explicitly using theMEASUrement:REFLevels:REFLevel:ABSolutecommands. This method is useful when precise values are required.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:MODE command.
Description
- This command sets or queries how often reference levels are calculated.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:MODE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:MODE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:MODE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?
Info
LATChcalculates reference levels only on the first acquisition after a statistics reset.CONTinuouscalculates reference levels on every acquisition.
Bases: SCPICmdRead
The MEASUrement:REFLevels:PERCent command tree.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.fallhigh: TheMEASUrement:REFLevels:PERCent:FALLHighcommand..falllow: TheMEASUrement:REFLevels:PERCent:FALLLowcommand..fallmid: TheMEASUrement:REFLevels:PERCent:FALLMidcommand..hysteresis: TheMEASUrement:REFLevels:PERCent:HYSTeresiscommand..risehigh: TheMEASUrement:REFLevels:PERCent:RISEHighcommand..riselow: TheMEASUrement:REFLevels:PERCent:RISELowcommand..risemid: TheMEASUrement:REFLevels:PERCent:RISEMidcommand..type: TheMEASUrement:REFLevels:PERCent:TYPEcommand.
property
¶
fallhigh: MeasurementReflevelsPercentFallhigh
Return the MEASUrement:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the falling edge.
property
¶
falllow: MeasurementReflevelsPercentFalllow
Return the MEASUrement:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?
Info
<NR3>is the percentage used to calculate the mid reference level of the falling edge.
property
¶
fallmid: MeasurementReflevelsPercentFallmid
Return the MEASUrement:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the falling edge.
property
¶
hysteresis: MeasurementReflevelsPercentHysteresis
Return the MEASUrement:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?
Info
<NR3>is the percentage used to calculate the hysteresis of the reference level.
property
¶
risehigh: MeasurementReflevelsPercentRisehigh
Return the MEASUrement:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the rising edge.
property
¶
riselow: MeasurementReflevelsPercentRiselow
Return the MEASUrement:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?
Info
<NR3>is the percentage used to calculate the low reference level of the rising edge.
property
¶
risemid: MeasurementReflevelsPercentRisemid
Return the MEASUrement:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the rising edge.
property
¶
Return the MEASUrement:REFLevels:PERCent:TYPE command.
Description
- This command sets or queries the reference level percent type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?
Info
TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:FALLHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:FALLHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:FALLHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:FALLHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:FALLLow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:FALLLow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:FALLLow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:FALLLow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?
Info
<NR3>is the percentage used to calculate the mid reference level of the falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:FALLMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:FALLMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:FALLMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:FALLMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the falling edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:HYSTeresis command.
Description
- This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:HYSTeresis?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:HYSTeresis?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:HYSTeresis valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?
Info
<NR3>is the percentage used to calculate the hysteresis of the reference level.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:RISEHigh command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:RISEHigh?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:RISEHigh?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:RISEHigh valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?
Info
<NR3>is the percentage used to calculate the high reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:RISELow command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:RISELow?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:RISELow?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:RISELow valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?
Info
<NR3>is the percentage used to calculate the low reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:RISEMid command.
Description
- This command sets or queries the percentage (where 100% is equal to TOP and 0% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:RISEMid?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:RISEMid?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:RISEMid valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?
Info
<NR3>is the percentage used to calculate the mid reference level of the rising edge.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:PERCent:TYPE command.
Description
- This command sets or queries the reference level percent type for the measurement.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:PERCent:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:PERCent:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:PERCent:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?
Info
TENNinetysets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.TWENtyeightysets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.CUSTomallows setting other reference level percents.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:REFLevels:TYPE command.
Description
- This command sets or queries the shared reference level method used for sources of measurement calculations.
Usage
- Using the
.query()method will send theMEASUrement:REFLevels:TYPE?query. - Using the
.verify(value)method will send theMEASUrement:REFLevels:TYPE?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:REFLevels:TYPE valuecommand.
SCPI Syntax
- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?
Info
GLOBalshares reference levels across measurements.PERSourcecauses reference levels to be used on individual measurements.
Bases: SCPICmdRead
The MEASUrement:RESUlts command tree.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.history: TheMEASUrement:RESUlts:HISTorycommand tree.
property
¶
history: MeasurementResultsHistory
Return the MEASUrement:RESUlts:HISTory command tree.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts:HISTory?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts:HISTory?query and raise an AssertionError if the returned value does not matchvalue.
Sub-properties
.start: TheMEASUrement:RESUlts:HISTory:STARtcommand..stop: TheMEASUrement:RESUlts:HISTory:STOPcommand.
Bases: SCPICmdRead
The MEASUrement:RESUlts:HISTory command tree.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts:HISTory?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts:HISTory?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.start: TheMEASUrement:RESUlts:HISTory:STARtcommand..stop: TheMEASUrement:RESUlts:HISTory:STOPcommand.
property
¶
Return the MEASUrement:RESUlts:HISTory:STARt command.
Description
- This command sets or queries the starting acquisition number for transferring measurement history results.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts:HISTory:STARt?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts:HISTory:STARt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:RESUlts:HISTory:STARt valuecommand.
SCPI Syntax
- MEASUrement:RESUlts:HISTory:STARt <NR1>
- MEASUrement:RESUlts:HISTory:STARt?
Info
<NR1>is the first acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred from acquisitionsto MEASUrement:RESUlts:HISTory:STOP.
property
¶
Return the MEASUrement:RESUlts:HISTory:STOP command.
Description
- This command sets or queries the last acquisition number that will be transferred for measurement history results.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts:HISTory:STOP?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts:HISTory:STOP?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:RESUlts:HISTory:STOP valuecommand.
SCPI Syntax
- MEASUrement:RESUlts:HISTory:STOP <NR1>
- MEASUrement:RESUlts:HISTory:STOP?
Info
<NR1>is the last acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred fromMEASUrement:RESUlts:HISTory:STARtto. A special value of 0 for indicates that the stop position is always the last history acquisition.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:RESUlts:HISTory:STARt command.
Description
- This command sets or queries the starting acquisition number for transferring measurement history results.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts:HISTory:STARt?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts:HISTory:STARt?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:RESUlts:HISTory:STARt valuecommand.
SCPI Syntax
- MEASUrement:RESUlts:HISTory:STARt <NR1>
- MEASUrement:RESUlts:HISTory:STARt?
Info
<NR1>is the first acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred from acquisitionsto MEASUrement:RESUlts:HISTory:STOP.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:RESUlts:HISTory:STOP command.
Description
- This command sets or queries the last acquisition number that will be transferred for measurement history results.
Usage
- Using the
.query()method will send theMEASUrement:RESUlts:HISTory:STOP?query. - Using the
.verify(value)method will send theMEASUrement:RESUlts:HISTory:STOP?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:RESUlts:HISTory:STOP valuecommand.
SCPI Syntax
- MEASUrement:RESUlts:HISTory:STOP <NR1>
- MEASUrement:RESUlts:HISTory:STOP?
Info
<NR1>is the last acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred fromMEASUrement:RESUlts:HISTory:STARtto. A special value of 0 for indicates that the stop position is always the last history acquisition.
Bases: SCPICmdRead
The MEASUrement:STATIstics command tree.
Usage
- Using the
.query()method will send theMEASUrement:STATIstics?query. - Using the
.verify(value)method will send theMEASUrement:STATIstics?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.cyclemode: TheMEASUrement:STATIstics:CYCLEModecommand.
property
¶
cyclemode: MeasurementStatisticsCyclemode
Return the MEASUrement:STATIstics:CYCLEMode command.
Description
- This command turns on and off cycle to cycle measurement statistics tracking and affects computation and display of cycle-cycle statistics in the Measurement Result table. It affects measurement statistics after being enabled and after new data is acquired and measured.
Usage
- Using the
.query()method will send theMEASUrement:STATIstics:CYCLEMode?query. - Using the
.verify(value)method will send theMEASUrement:STATIstics:CYCLEMode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:STATIstics:CYCLEMode valuecommand.
SCPI Syntax
- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?
Info
OFFturns off statistics for all measurements. This is the default value.ONturns on statistics and displays all statistics for each measurement.0turns off statistics for all measurements.1turns on statistics and displays all statistics for each measurement.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:STATIstics:CYCLEMode command.
Description
- This command turns on and off cycle to cycle measurement statistics tracking and affects computation and display of cycle-cycle statistics in the Measurement Result table. It affects measurement statistics after being enabled and after new data is acquired and measured.
Usage
- Using the
.query()method will send theMEASUrement:STATIstics:CYCLEMode?query. - Using the
.verify(value)method will send theMEASUrement:STATIstics:CYCLEMode?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:STATIstics:CYCLEMode valuecommand.
SCPI Syntax
- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?
Info
OFFturns off statistics for all measurements. This is the default value.ONturns on statistics and displays all statistics for each measurement.0turns off statistics for all measurements.1turns on statistics and displays all statistics for each measurement.
Bases: SCPICmdRead
The MEASUrement:WBG command tree.
Usage
- Using the
.query()method will send theMEASUrement:WBG?query. - Using the
.verify(value)method will send theMEASUrement:WBG?query and raise an AssertionError if the returned value does not matchvalue.
Properties
.pdevice: TheMEASUrement:WBG:PDEVicecommand.
property
¶
pdevice: MeasurementWbgPdevice
Return the MEASUrement:WBG:PDEVice command.
Description
- This command sets or returns the type of the Power device.
Usage
- Using the
.query()method will send theMEASUrement:WBG:PDEVice?query. - Using the
.verify(value)method will send theMEASUrement:WBG:PDEVice?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:WBG:PDEVice valuecommand.
SCPI Syntax
- MEASUrement:WBG:PDEVice {IGBT|MOSFET}
- MEASUrement:WBG:PDEVice?
Info
IGBTspecifies the type of the Power device as IGBT.MOSFETspecifies the type of the Power device as MOSFET.
Bases: SCPICmdWrite, SCPICmdRead
The MEASUrement:WBG:PDEVice command.
Description
- This command sets or returns the type of the Power device.
Usage
- Using the
.query()method will send theMEASUrement:WBG:PDEVice?query. - Using the
.verify(value)method will send theMEASUrement:WBG:PDEVice?query and raise an AssertionError if the returned value does not matchvalue. - Using the
.write(value)method will send theMEASUrement:WBG:PDEVice valuecommand.
SCPI Syntax
- MEASUrement:WBG:PDEVice {IGBT|MOSFET}
- MEASUrement:WBG:PDEVice?
Info
IGBTspecifies the type of the Power device as IGBT.MOSFETspecifies the type of the Power device as MOSFET.