measurement ¶

The measurement commands module.

These commands are used in the following models: LPD6, MSO4, MSO4B, MSO5, MSO5B, MSO5LP, MSO6, MSO6B

THIS FILE IS AUTO-GENERATED, IT SHOULD NOT BE MANUALLY MODIFIED.

Please report an issue if one is found.

Commands and Queries

- MEASUrement:ADDMEAS {ACCOMMONMODE|ACPR|ACRMS|AMPLITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|CCJITTER|COMMONMODE|CPOWER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMPSIJ|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HEIGHT|HEIGHTBER|HIGH|HIGHTIME|HOLD|IMDAANGLE|IMDADIRECTION|IMDADQ0|IMDAEFFICIENCY|IMDAHARMONICS|IMDAMECHPWR|IMDAPOWERQUALITY|IMDASPEED|IMDASYSEFF|IMDATORQUE|ISI|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NPJ|NWIDTH|OBW|PATTERNLENGTH|PDUTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SETUP|SKEW|SRJ|SSCFREQDEV|SSCMODRATE|SSCSLEWRATE|TIE|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WBGDDT|WBGDIODEDDT|WBGEOFF|WBGEON|WBGERR|WBGIPEAK|WBGIRRM|WBGQOSS|WBGQRR|WBGTDOFF|WBGTDON|WBGTF|WBGTON|WBGTOFF|WBGTR|WBGTRR|WBGTDT|WBGVPEAK|WIDTH|WIDTHBER}
- MEASUrement:ADDNew <QString>
- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?
- MEASUrement:AUTOset {DPMAutoset|DPMPReset|EXECute|THREEPHASEAUTOset|WBGDeskewexec|WBGPREset|WBGGSTIM}
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh M <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?
- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?
- MEASUrement:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:CLOCKRecovery:ADVanced:METHod?
- MEASUrement:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:CLOCKRecovery:CLOCKFrequency?
- MEASUrement:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:CLOCKRecovery:CLOCKMultiplier?
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe?
- MEASUrement:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:CLOCKRecovery:DAMPing?
- MEASUrement:CLOCKRecovery:DATAPath <QString>
- MEASUrement:CLOCKRecovery:DATAPath?
- MEASUrement:CLOCKRecovery:DATARate <NR3>
- MEASUrement:CLOCKRecovery:DATARate?
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?
- MEASUrement:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:CLOCKRecovery:JTFBandwidth?
- MEASUrement:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:CLOCKRecovery:LOOPBandwidth?
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate?
- MEASUrement:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:CLOCKRecovery:METHod?
- MEASUrement:CLOCKRecovery:MODel TYPE<x>
- MEASUrement:CLOCKRecovery:MODel?
- MEASUrement:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
- MEASUrement:CLOCKRecovery:NOMINALOFFset?
- MEASUrement:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:CLOCKRecovery:STAndard?
- MEASUrement:CLOCKRecovery:TDCOMPensation {1|0}
- MEASUrement:CLOCKRecovery:TDCOMPensation?
- MEASUrement:DDJMethod {SPECtraldomain|TIMDomain}
- MEASUrement:DDJMethod?
- MEASUrement:DELETEALL
- MEASUrement:DELete <QString>
- MEASUrement:DIRacmodel {PCIExpress|FIBREchannel}
- MEASUrement:DIRacmodel?
- MEASUrement:DISPLAYUnits {SEConds|UNITINtervals}
- MEASUrement:DISPLAYUnits?
- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:EDGE<x>?
- MEASUrement:ENABLEPjitter {ON|OFF|1|0}
- MEASUrement:ENABLEPjitter?
- MEASUrement:EYERENDER {ON|OFF|<NR1>}
- MEASUrement:EYERENDER?
- MEASUrement:FILTers:BLANKingtime <NR3>
- MEASUrement:FILTers:BLANKingtime?
- MEASUrement:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:FILTers:HIGHPass:FREQ?
- MEASUrement:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:HIGHPass:SPEC?
- MEASUrement:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:FILTers:LOWPass:FREQ?
- MEASUrement:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:LOWPass:SPEC?
- MEASUrement:FILTers:RAMPtime <NR3>
- MEASUrement:FILTers:RAMPtime?
- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?
- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?
- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?
- MEASUrement:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?
- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?
- MEASUrement:GATing:SEARCHSource SEARCH<x>
- MEASUrement:GATing:SEARCHSource?
- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?
- MEASUrement:GATing?
- MEASUrement:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:HIGHLEVel:CONFIGuration?
- MEASUrement:HIGHLEVel:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:EDGEQUALifier?
- MEASUrement:HIGHLEVel:INLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:INLOWPass:FREQ?
- MEASUrement:HIGHLEVel:INLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:INLOWPass:SPEC?
- MEASUrement:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:L2LTOL2N?
- MEASUrement:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:HIGHLEVel:LINESelected?
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier?
- MEASUrement:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:OUTL2LTOL2N?
- MEASUrement:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:HIGHLEVel:OUTLINESelected?
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ?
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC?
- MEASUrement:HIGHLEVel:OUTSOURCE {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTSOURCE?
- MEASUrement:HIGHLEVel:OUTWIRing {P1W2V1I1|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:OUTWIRing?
- MEASUrement:HIGHLEVel:SOURCE {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:SOURCE?
- MEASUrement:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:WIRing?
- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?
- MEASUrement:JITTermodel {SPECTRAL|SPECTRALBUJ}
- MEASUrement:JITTermodel?
- MEASUrement:LIST?
- MEASUrement:LOCKRJ {ON|OFF|1|0}
- MEASUrement:LOCKRJ?
- MEASUrement:LOCKRJValue <NR3>
- MEASUrement:LOCKRJValue?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?
- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?
- MEASUrement:MEAS<x>:ABANdwidth <NR3>
- MEASUrement:MEAS<x>:ABANdwidth?
- MEASUrement:MEAS<x>:ACHANnels <NR3>
- MEASUrement:MEAS<x>:ACHANnels?
- MEASUrement:MEAS<x>:AMEThod {PARAmetric|HISTogram}
- MEASUrement:MEAS<x>:AMEThod?
- MEASUrement:MEAS<x>:BCOunt <NR3>
- MEASUrement:MEAS<x>:BCOunt?
- MEASUrement:MEAS<x>:BDELay <NR3>
- MEASUrement:MEAS<x>:BDELay?
- MEASUrement:MEAS<x>:BER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER?
- MEASUrement:MEAS<x>:BER?
- MEASUrement:MEAS<x>:BIN <NR3>
- MEASUrement:MEAS<x>:BIN?
- MEASUrement:MEAS<x>:BITAbsolute <NR3>
- MEASUrement:MEAS<x>:BITAbsolute?
- MEASUrement:MEAS<x>:BITCfgmode {MEAN|MODE}
- MEASUrement:MEAS<x>:BITCfgmode?
- MEASUrement:MEAS<x>:BITEnd <NR3>
- MEASUrement:MEAS<x>:BITEnd?
- MEASUrement:MEAS<x>:BITPcnt <NR3>
- MEASUrement:MEAS<x>:BITPcnt?
- MEASUrement:MEAS<x>:BITSTart <NR3>
- MEASUrement:MEAS<x>:BITSTart?
- MEASUrement:MEAS<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- MEASUrement:MEAS<x>:BITType?
- MEASUrement:MEAS<x>:BMTYPe {TIE|PERIOD|NUInterval}
- MEASUrement:MEAS<x>:BMTYPe?
- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?
- MEASUrement:MEAS<x>:BVOLTage <NR3>
- MEASUrement:MEAS<x>:BVOLTage?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?
- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?
- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?
- MEASUrement:MEAS<x>:CF<x>Val <NR3>
- MEASUrement:MEAS<x>:CF<x>Val?
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?
- MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath <QString>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate?
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod?
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel TYPE<x>
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel?
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?
- MEASUrement:MEAS<x>:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation {0|1}
- MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation?
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs {SINGLE|DOUBLE}
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs?
- MEASUrement:MEAS<x>:COVer {FFREQuency|AFREQuencies}
- MEASUrement:MEAS<x>:COVer?
- MEASUrement:MEAS<x>:CPWIDTh <NR3>
- MEASUrement:MEAS<x>:CPWIDTh?
- MEASUrement:MEAS<x>:CSPACing <NR3>
- MEASUrement:MEAS<x>:CSPACing?
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile <QString>
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile?
- MEASUrement:MEAS<x>:CYCLemode {RECORD|CYCLE|ROTATION}
- MEASUrement:MEAS<x>:CYCLemode?
- MEASUrement:MEAS<x>:DBDown <NR3>
- MEASUrement:MEAS<x>:DBDown?
- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?
- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?
- MEASUrement:MEAS<x>:DMEThod {AUTO|MANual}
- MEASUrement:MEAS<x>:DMEThod?
- MEASUrement:MEAS<x>:DVDS {OFF|ON}
- MEASUrement:MEAS<x>:DVDS?
- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:MEAS<x>:EDGE<x>?
- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?
- MEASUrement:MEAS<x>:EDGEQUALONE <QString>
- MEASUrement:MEAS<x>:EDGEQUALONE?
- MEASUrement:MEAS<x>:EDGEQUALTWO <QString>
- MEASUrement:MEAS<x>:EDGEQUALTWO?
- MEASUrement:MEAS<x>:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:EDGEQUALifier?
- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?
- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency?
- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?
- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency?
- MEASUrement:MEAS<x>:EEQUal {ON|OFF}
- MEASUrement:MEAS<x>:EEQUal?
- MEASUrement:MEAS<x>:EINDuctance <NR3>
- MEASUrement:MEAS<x>:EINDuctance?
- MEASUrement:MEAS<x>:EINTerpolation {ON|OFF}
- MEASUrement:MEAS<x>:EINTerpolation?
- MEASUrement:MEAS<x>:EXTENDuis <NR1>
- MEASUrement:MEAS<x>:EXTENDuis?
- MEASUrement:MEAS<x>:EYERender {FAst|COMPlete}
- MEASUrement:MEAS<x>:EYERender?
- MEASUrement:MEAS<x>:FAILCount?
- MEASUrement:MEAS<x>:FCOunt <NR3>
- MEASUrement:MEAS<x>:FCOunt?
- MEASUrement:MEAS<x>:FILTERRANGEFROM <NR3>
- MEASUrement:MEAS<x>:FILTERRANGEFROM?
- MEASUrement:MEAS<x>:FILTERRANGETO <NR3>
- MEASUrement:MEAS<x>:FILTERRANGETO?
- MEASUrement:MEAS<x>:FILTers:BLANKingtime <NR3>
- MEASUrement:MEAS<x>:FILTers:BLANKingtime?
- MEASUrement:MEAS<x>:FILTers:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:FILTers:GLOBal?
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?
- MEASUrement:MEAS<x>:FILTers:RAMPtime <NR3>
- MEASUrement:MEAS<x>:FILTers:RAMPtime?
- MEASUrement:MEAS<x>:FORDer <NR3>
- MEASUrement:MEAS<x>:FORDer?
- MEASUrement:MEAS<x>:FPARAmeter <NR3>
- MEASUrement:MEAS<x>:FPARAmeter?
- MEASUrement:MEAS<x>:FREQ <NR3>
- MEASUrement:MEAS<x>:FREQ?
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?
- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?
- MEASUrement:MEAS<x>:FTYPe {True|False}
- MEASUrement:MEAS<x>:FTYPe?
- MEASUrement:MEAS<x>:FUNDCURRent <NR3>
- MEASUrement:MEAS<x>:FUNDCURRent?
- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?
- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?
- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?
- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?
- MEASUrement:MEAS<x>:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?
- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
- MEASUrement:MEAS<x>:GATing:SEARCHSource?
- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?
- MEASUrement:MEAS<x>:GATing?
- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?
- MEASUrement:MEAS<x>:HARMONICSCLass {CLASSA|CLASSB|CLASSC|CLASSD}
- MEASUrement:MEAS<x>:HARMONICSCLass?
- MEASUrement:MEAS<x>:HARMONICSSOURce {CURRENT|VOLTAGE}
- MEASUrement:MEAS<x>:HARMONICSSOURce?
- MEASUrement:MEAS<x>:HARMONICSStd {NONE|IEC|IEEE519|CUSTOM|REVIEEE5192022}
- MEASUrement:MEAS<x>:HARMONICSStd?
- MEASUrement:MEAS<x>:HARMONICSUNits {LOGARITHM|LINEAR}
- MEASUrement:MEAS<x>:HARMONICSUNits?
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected?
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL {ON|OFF|1|0}
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing?
- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal {ON|OFF}
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?
- MEASUrement:MEAS<x>:HTORque <NR1>
- MEASUrement:MEAS<x>:HTORque?
- MEASUrement:MEAS<x>:HVOLtage <NR1>
- MEASUrement:MEAS<x>:HVOLtage?
- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?
- MEASUrement:MEAS<x>:INPUTLEVel <NR2>
- MEASUrement:MEAS<x>:INPUTLEVel?
- MEASUrement:MEAS<x>:INPUTPOwer <NR3>
- MEASUrement:MEAS<x>:INPUTPOwer?
- MEASUrement:MEAS<x>:JITTERSummary:DCD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DCD?
- MEASUrement:MEAS<x>:JITTERSummary:DDJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DDJ?
- MEASUrement:MEAS<x>:JITTERSummary:DJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJ?
- MEASUrement:MEAS<x>:JITTERSummary:DJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJDD?
- MEASUrement:MEAS<x>:JITTERSummary:DR {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DR?
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?
- MEASUrement:MEAS<x>:JITTERSummary:ISI {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:ISI?
- MEASUrement:MEAS<x>:JITTERSummary:NPJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:NPJ?
- MEASUrement:MEAS<x>:JITTERSummary:PJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PJ?
- MEASUrement:MEAS<x>:JITTERSummary:PL {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PL?
- MEASUrement:MEAS<x>:JITTERSummary:RJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJ?
- MEASUrement:MEAS<x>:JITTERSummary:RJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJDD?
- MEASUrement:MEAS<x>:JITTERSummary:TIE {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TIE?
- MEASUrement:MEAS<x>:JITTERSummary:TJBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TJBER?
- MEASUrement:MEAS<x>:LABel <QString>
- MEASUrement:MEAS<x>:LABel?
- MEASUrement:MEAS<x>:LINESelected {ABCB|ACBC|BACA|XYZY|XZYZ|YXZX}
- MEASUrement:MEAS<x>:LINESelected?
- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?
- MEASUrement:MEAS<x>:LTORque <NR1>
- MEASUrement:MEAS<x>:LTORque?
- MEASUrement:MEAS<x>:LTYPe {AUTO|CUSTom}
- MEASUrement:MEAS<x>:LTYPe?
- MEASUrement:MEAS<x>:LUNITs {PERCent|ABSolute}
- MEASUrement:MEAS<x>:LUNITs?
- MEASUrement:MEAS<x>:LVOLtage <NR1>
- MEASUrement:MEAS<x>:LVOLtage?
- MEASUrement:MEAS<x>:MATime <NR3>
- MEASUrement:MEAS<x>:MATime?
- MEASUrement:MEAS<x>:MAXCUrrent <NR3>
- MEASUrement:MEAS<x>:MAXCUrrent?
- MEASUrement:MEAS<x>:MAXCycle <NR1>
- MEASUrement:MEAS<x>:MAXCycle?
- MEASUrement:MEAS<x>:MAXG1Voltage <NR3>
- MEASUrement:MEAS<x>:MAXG1Voltage?
- MEASUrement:MEAS<x>:MAXG2Voltage <NR3>
- MEASUrement:MEAS<x>:MAXG2Voltage?
- MEASUrement:MEAS<x>:MAXGVoltage <NR3>
- MEASUrement:MEAS<x>:MAXGVoltage?
- MEASUrement:MEAS<x>:MAXVoltage <NR2>
- MEASUrement:MEAS<x>:MAXVoltage?
- MEASUrement:MEAS<x>:MEASRange:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:GLOBal?
- MEASUrement:MEAS<x>:MEASRange:MAX <NR3>
- MEASUrement:MEAS<x>:MEASRange:MAX?
- MEASUrement:MEAS<x>:MEASRange:MIN <NR3>
- MEASUrement:MEAS<x>:MEASRange:MIN?
- MEASUrement:MEAS<x>:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:STATE?
- MEASUrement:MEAS<x>:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MECH:EINDexz?
- MEASUrement:MEAS<x>:MECH:GRATio <NR3>
- MEASUrement:MEAS<x>:MECH:GRATio?
- MEASUrement:MEAS<x>:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MEAS<x>:MECH:MUNits?
- MEASUrement:MEAS<x>:MECH:PPAirs <NR1>
- MEASUrement:MEAS<x>:MECH:PPAirs?
- MEASUrement:MEAS<x>:MECH:PPRotation <NR1>
- MEASUrement:MEAS<x>:MECH:PPRotation?
- MEASUrement:MEAS<x>:MECH:STYPe {HSENSOR|QEI|RESOLVER}
- MEASUrement:MEAS<x>:MECH:STYPe?
- MEASUrement:MEAS<x>:MINCycle <NR1>
- MEASUrement:MEAS<x>:MINCycle?
- MEASUrement:MEAS<x>:NVALUe <N>
- MEASUrement:MEAS<x>:NVALUe?
- MEASUrement:MEAS<x>:OBWMethod {percOfPwr|dBDown}
- MEASUrement:MEAS<x>:OBWMethod?
- MEASUrement:MEAS<x>:ODDEVen {ALL|EVEN|ODD}
- MEASUrement:MEAS<x>:ODDEVen?
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?
- MEASUrement:MEAS<x>:OSANgle <NR1>
- MEASUrement:MEAS<x>:OSANgle?
- MEASUrement:MEAS<x>:OUTEDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:OUTEDGEQUALifier?
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ <NR2>
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?
- MEASUrement:MEAS<x>:OUTPUT<x>VOLTage <NR2>
- MEASUrement:MEAS<x>:OUTPUT<x>VOLTage?
- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?
- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?
- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?
- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?
- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?
- MEASUrement:MEAS<x>:PATTERNDETECTION {AUTO|MANUAL}
- MEASUrement:MEAS<x>:PATTERNDETECTION?
- MEASUrement:MEAS<x>:PATTERNLENgth <NR3>
- MEASUrement:MEAS<x>:PATTERNLENgth?
- MEASUrement:MEAS<x>:PATTERNTYPe {REPeating|ARBitrary}
- MEASUrement:MEAS<x>:PATTERNTYPe?
- MEASUrement:MEAS<x>:PCOUNt <NR3>
- MEASUrement:MEAS<x>:PCOUNt?
- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
- MEASUrement:MEAS<x>:PERFREQ:EDGE?
- MEASUrement:MEAS<x>:PFREquency <NR3>
- MEASUrement:MEAS<x>:PFREquency?
- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?
- MEASUrement:MEAS<x>:POPUlation:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:GLOBal?
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue <NR3>
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?
- MEASUrement:MEAS<x>:POPower <NR3>
- MEASUrement:MEAS<x>:POPower?
- MEASUrement:MEAS<x>:POWERFACtor <NR2>
- MEASUrement:MEAS<x>:POWERFACtor?
- MEASUrement:MEAS<x>:PREGion {FPULse|SPULse|MPULse}
- MEASUrement:MEAS<x>:PREGion?
- MEASUrement:MEAS<x>:PRESistance <NR3>
- MEASUrement:MEAS<x>:PRESistance?
- MEASUrement:MEAS<x>:PTHReshold <NR3>
- MEASUrement:MEAS<x>:PTHReshold?
- MEASUrement:MEAS<x>:PWIDth <NR3>
- MEASUrement:MEAS<x>:PWIDth?
- MEASUrement:MEAS<x>:REDGe {ON|OFF}
- MEASUrement:MEAS<x>:REDGe?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?
- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?
- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?
- MEASUrement:MEAS<x>:REFVOLTAGE<x>Val <NR2>
- MEASUrement:MEAS<x>:REFVOLTAGE<x>Val?
- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?
- MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?
- MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?
- MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?
- MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?
- MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?
- MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?
- MEASUrement:MEAS<x>:RFREquency <NR3>
- MEASUrement:MEAS<x>:RFREquency?
- MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val <NR3>
- MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val?
- MEASUrement:MEAS<x>:RRANGE <NR3>
- MEASUrement:MEAS<x>:RRANGE?
- MEASUrement:MEAS<x>:SEQuence {ABC|ACB}
- MEASUrement:MEAS<x>:SEQuence?
- MEASUrement:MEAS<x>:SIGNALFREQUEncy {AUTO|FIFTYHZ|SIXTYHZ|FOURHUNDREDHZ|CUSTOM}
- MEASUrement:MEAS<x>:SIGNALFREQUEncy?
- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?
- MEASUrement:MEAS<x>:SLABs <NR3>
- MEASUrement:MEAS<x>:SLABs?
- MEASUrement:MEAS<x>:SLPCt <NR3>
- MEASUrement:MEAS<x>:SLPCt?
- MEASUrement:MEAS<x>:SLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:SLTYpe?
- MEASUrement:MEAS<x>:SMOOTHINGFILTER <NR1>
- MEASUrement:MEAS<x>:SOURCE {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:SOUrce1
- MEASUrement:MEAS<x>:SOUrce1?
- MEASUrement:MEAS<x>:SPAN<x>Val <NR3>
- MEASUrement:MEAS<x>:SPAN<x>Val?
- MEASUrement:MEAS<x>:SRATe <NR3>
- MEASUrement:MEAS<x>:SRATe?
- MEASUrement:MEAS<x>:SRHo {ON|OFF}
- MEASUrement:MEAS<x>:SRHo?
- MEASUrement:MEAS<x>:SSC:NOMinalfreq <NR3>
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANual}
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?
- MEASUrement:MEAS<x>:SSC:NOMinalfreq?
- MEASUrement:MEAS<x>:SSDirection {FORWARD|BACKWARD}
- MEASUrement:MEAS<x>:SSDirection?
- MEASUrement:MEAS<x>:STATUS?
- MEASUrement:MEAS<x>:STLABs <NR3>
- MEASUrement:MEAS<x>:STLABs?
- MEASUrement:MEAS<x>:STLPct <NR3>
- MEASUrement:MEAS<x>:STLPct?
- MEASUrement:MEAS<x>:STLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:STLTYpe?
- MEASUrement:MEAS<x>:STSDirection {FORWARD|BACKWARD}
- MEASUrement:MEAS<x>:STSDirection?
- MEASUrement:MEAS<x>:STYPe {VOLTage|CURRent|DIFFERENTIAL|SINGLE}
- MEASUrement:MEAS<x>:STYPe?
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation? <QString>
- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev? <QString>
- MEASUrement:MEAS<x>:SUNits {RPM|HZ}
- MEASUrement:MEAS<x>:SUNits?
- MEASUrement:MEAS<x>:TCKAVG <NR3>
- MEASUrement:MEAS<x>:TCKAVG?
- MEASUrement:MEAS<x>:TCONstant <NR1>
- MEASUrement:MEAS<x>:TCONstant?
- MEASUrement:MEAS<x>:TDRPreset {EXECUTE}
- MEASUrement:MEAS<x>:TIMINGMode {EACHCLOCKCYCLE|TWOCLOCKCYCLES}
- MEASUrement:MEAS<x>:TIMINGMode?
- MEASUrement:MEAS<x>:TLEVel {PERCent|ABSolute}
- MEASUrement:MEAS<x>:TLEVel?
- MEASUrement:MEAS<x>:TMEThod {SENSOR|CURRENT}
- MEASUrement:MEAS<x>:TMEThod?
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?
- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?
- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:TYPe {ACCOMMONMODE|ACPR|ACRMS|AMPLITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|CPOWER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMOVERSHOOT|DPMPSIJ|DPMUNDERSHOOT|DPMRIPPLE|DPMTURNOFFTIME|DPMTURNONTIME|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HIGH|HEIGHT|HEIGHTBER|HIGHTIME|HOLD|IMDAANGLE|IMDADIRECTION|IMDADQ0|IMDAEFFICIENCY|IMDAHARMONICS|IMDAMECHPWR|IMDAPOWERQUALITY|IMDASPEED|IMDASYSEFF|IMDATORQUE|ISI|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NPJ|NOVERSHOOT|NWIDTH|OBW|PATTERNLENGTH|PDUTTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RDSON|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SRJ|SSCFREQDEV|SSCMODRATE|SSCSLEWRATE|SETUP|SKEW|TDR|TIE|TIMEOUTSIDELEVEL|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WBGDDT|WBGDIODEDDT|WBGEOFF|WBGEON|WBGERR|WBGIPEAK|WBGIRRM|WBGQOSS|WBGQRR|WBGTDOFF|WBGTDON|WBGTF|WBGTON|WBGTOFF|WBGTR|WBGTRR|WBGTDT|WBGVPEAK|WIDTH|WIDTHBER}
- MEASUrement:MEAS<x>:TYPe?
- MEASUrement:MEAS<x>:VLEVel {PERCent|ABSolute}
- MEASUrement:MEAS<x>:VLEVel?
- MEASUrement:MEAS<x>:WAITTime <NR2>
- MEASUrement:MEAS<x>:WAITTime?
- MEASUrement:MEAS<x>:WBG:AFGSetup {CONNECT|RUN}
- MEASUrement:MEAS<x>:WBG:AFGaddress <QString>
- MEASUrement:MEAS<x>:WBG:AFGaddress?
- MEASUrement:MEAS<x>:WBG:CSTatus?
- MEASUrement:MEAS<x>:WBG:GTYPe {AFG31000|OTHER}
- MEASUrement:MEAS<x>:WBG:GTYPe?
- MEASUrement:MEAS<x>:WBG:HIGH <NR3>
- MEASUrement:MEAS<x>:WBG:HIGH?
- MEASUrement:MEAS<x>:WBG:LOAD {FIFTY|HIGHZ}
- MEASUrement:MEAS<x>:WBG:LOAD?
- MEASUrement:MEAS<x>:WBG:LOW <NR3>
- MEASUrement:MEAS<x>:WBG:LOW?
- MEASUrement:MEAS<x>:WBG:NPULs <NR1>
- MEASUrement:MEAS<x>:WBG:NPULs?
- MEASUrement:MEAS<x>:WBG:PG<x>Val <NR3>
- MEASUrement:MEAS<x>:WBG:PG<x>Val?
- MEASUrement:MEAS<x>:WBG:PW<x>Val <NR3>
- MEASUrement:MEAS<x>:WBG:PW<x>Val?
- MEASUrement:MEAS<x>:WBG:TIMer <NR3>
- MEASUrement:MEAS<x>:WBG:TIMer?
- MEASUrement:MEAS<x>:WIDTh <NR1>
- MEASUrement:MEAS<x>:WIDTh?
- MEASUrement:MEAS<x>:WINDOWLENgth <NR3>
- MEASUrement:MEAS<x>:WINDOWLENgth?
- MEASUrement:MEAS<x>:XUNIT?
- MEASUrement:MEAS<x>:YUNIT?
- MEASUrement:MEASRange:MAX <NR3>
- MEASUrement:MEASRange:MAX?
- MEASUrement:MEASRange:MIN <NR3>
- MEASUrement:MEASRange:MIN?
- MEASUrement:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEASRange:STATE?
- MEASUrement:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MECH:EINDexz?
- MEASUrement:MECH:GRATio <NR3>
- MEASUrement:MECH:GRATio?
- MEASUrement:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MECH:MUNits?
- MEASUrement:MECH:PPAirs <NR1>
- MEASUrement:MECH:PPAirs?
- MEASUrement:MECH:PPRotation <NR1>
- MEASUrement:MECH:PPRotation?
- MEASUrement:MECH:SOUrce1 {CH<x>|MATH<x>|REF<x>|CH<x>_D<x>}
- MEASUrement:MECH:SOUrce1?
- MEASUrement:MECH:STYPe {HSENSOR|QEI|RESOLVER}
- MEASUrement:MECH:STYPe?
- MEASUrement:MINUI <NR3>
- MEASUrement:MINUI?
- MEASUrement:POPUlation:LIMIT:STATE {OFF|ON|0|1 }
- MEASUrement:POPUlation:LIMIT:STATE?
- MEASUrement:POPUlation:LIMIT:VALue <NR1>
- MEASUrement:POPUlation:LIMIT:VALue?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?
- MEASUrement:REF<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REF<x>:REFLevels:BASETop?
- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?
- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?
- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?
- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?
- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?
- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?
- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?
- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?
- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?
- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?
- MEASUrement:REFLevels:JITTERMODE {CONTinuous|LATCh}
- MEASUrement:REFLevels:JITTERMODE?
- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?
- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?
- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?
- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?
- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?
- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?
- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?
- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?
- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?
- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?
- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?
- MEASUrement:RESUlts:HISTory:STARt <NR1>
- MEASUrement:RESUlts:HISTory:STARt?
- MEASUrement:RESUlts:HISTory:STOP <NR1>
- MEASUrement:RESUlts:HISTory:STOP?
- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?
- MEASUrement:WBG:PDEVice {IGBT|MOSFET}
- MEASUrement:WBG:PDEVice?
- MEASUrement?

Measurement ¶

Bases: SCPICmdRead

The MEASUrement command.

Description

This query-only command returns all measurement parameters.

Usage

Using the .query() method will send the MEASUrement? query.
Using the .verify(value) method will send the MEASUrement? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement?

Properties

.addmeas: The MEASUrement:ADDMEAS command.
.addnew: The MEASUrement:ADDNew command.
.annotate: The MEASUrement:ANNOTate command.
.autoset: The MEASUrement:AUTOset command.
.ch: The MEASUrement:CH<x> command tree.
.clockrecovery: The MEASUrement:CLOCKRecovery command tree.
.ddjmethod: The MEASUrement:DDJMethod command.
.deleteall: The MEASUrement:DELETEALL command.
.delete: The MEASUrement:DELete command.
.diracmodel: The MEASUrement:DIRacmodel command.
.displayunits: The MEASUrement:DISPLAYUnits command.
.edge: The MEASUrement:EDGE<x> command.
.enablepjitter: The MEASUrement:ENABLEPjitter command.
.eyerender: The MEASUrement:EYERENDER command.
.filters: The MEASUrement:FILTers command tree.
.gating: The MEASUrement:GATing command.
.highlevel: The MEASUrement:HIGHLEVel command tree.
.interp: The MEASUrement:INTERp command.
.jittermodel: The MEASUrement:JITTermodel command.
.list: The MEASUrement:LIST command.
.lockrj: The MEASUrement:LOCKRJ command.
.lockrjvalue: The MEASUrement:LOCKRJValue command.
.math: The MEASUrement:MATH<x> command tree.
.meas: The MEASUrement:MEAS<x> command tree.
.measrange: The MEASUrement:MEASRange command tree.
.mech: The MEASUrement:MECH command tree.
.minui: The MEASUrement:MINUI command.
.population: The MEASUrement:POPUlation command tree.
.ref: The MEASUrement:REF<x> command tree.
.reflevels: The MEASUrement:REFLevels command tree.
.results: The MEASUrement:RESUlts command tree.
.statistics: The MEASUrement:STATIstics command tree.
.wbg: The MEASUrement:WBG command tree.

addmeas `property` ¶

addmeas: MeasurementAddmeas

Return the MEASUrement:ADDMEAS command.

Description

This command adds a measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDMEAS value command.

SCPI Syntax

- MEASUrement:ADDMEAS {ACCOMMONMODE|ACPR|ACRMS|AMPLITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|CCJITTER|COMMONMODE|CPOWER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMPSIJ|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HEIGHT|HEIGHTBER|HIGH|HIGHTIME|HOLD|IMDAANGLE|IMDADIRECTION|IMDADQ0|IMDAEFFICIENCY|IMDAHARMONICS|IMDAMECHPWR|IMDAPOWERQUALITY|IMDASPEED|IMDASYSEFF|IMDATORQUE|ISI|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NPJ|NWIDTH|OBW|PATTERNLENGTH|PDUTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SETUP|SKEW|SRJ|SSCFREQDEV|SSCMODRATE|SSCSLEWRATE|TIE|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WBGDDT|WBGDIODEDDT|WBGEOFF|WBGEON|WBGERR|WBGIPEAK|WBGIRRM|WBGQOSS|WBGQRR|WBGTDOFF|WBGTDON|WBGTF|WBGTON|WBGTOFF|WBGTR|WBGTRR|WBGTDT|WBGVPEAK|WIDTH|WIDTHBER}

Info

ACCOMMONMODE AC Common Mode (Pk-Pk) is the peak-to-peak of the commonmode voltage of two sources. This measurement is made across the entire record.This measurement requires the DJA option and is not available on a 4 SeriesMSO instrument.
ACPR (Adjacent Channel Power Ratio) is the amount of power that leaks intoadjacent channels. This can be specified in terms of absolute power or a ratio ofadjacent channel power to the main channel power, called adjacent channel powerratio (ACPR) or adjacent channel leakage ratio (ACLR).
ACRMS (AC RMS) is the true Root Mean Square of the data points, about theMean. This measurement can be made across the entire record, or on each cyclein the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BITAMPLITUDE (Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITHIGH (Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITLOW (Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
CCJITTER (Cycle-to-Cycle jitter) measures how much the clock period changes between any two adjacent cycles. Cycle-to-Cycle jitter is measured by applying a first order difference operation to the period jitter.
COMMONMODE (DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
CPOWER (Channel Power) is the measurement of integrated power within a specified channel bandwidth for a RF signal. The resulting channel power is an absolute power measurement.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DCD (duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDJ (data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDRAOS (area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.
DDRAOSPERTCK (area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAOSPERUI (area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRAUS (area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.
DDRAUSPERTCK (area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAUSPERUI (area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRHOLDDIFF (hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.
DDRSETUPDIFF (setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.
DDRTCHABS (absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.
DDRTCHAVERAGE (average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCKAVERAGE (average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCLABS (absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.
DDRTCLAVERAGE (average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.
DDRTERRMN (cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).
DDRTERRN (cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).
DDRTJITCC (cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.
DDRTJITDUTY (half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.
DDRTJITPER (clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.
DDRTPST (read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.
DDRTRPRE (read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRTWPRE is the width of theWrite burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRVIXAC is the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.
DDRTDQSCK is the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
DJ (deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DJDIRAC (dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DPMPSIJ is the Power Supply Induced Jitter. This measurement helps in suppressing the jitter in high speed signals (victim) induced from power rail signals (aggressor).
EYEHIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
EYELOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
F2 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F4 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F8 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.
HEIGHT (Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HEIGHTBER (Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
IMDAANGLE (Angle) measures the phase angle. Configure QEI or Hall sensor to.
compute the angle measurement. Requires a IMDA-MECH License.
IMDADIRECTION (Direction) defines the direction of rotation of the motor. Set the direction A-B-C or A-C-B for Hall sensors and CW or CCW for QEI based on the motor configuration. Requires a IMDA-MECH License.
IMDADQ0 measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0. Requires a IMDA-MECH License.
IMDAEFFICIENCY (Efficiency) measures the ratio of sum of output power(s) to input power for respective input and output Voltage and Current pairs. Note: the current release cannot support 3V and 3I pairs, since this requires 12 channels. We restrict to 2V and 2I which needs 8 scope channels. Requires a IMDA-MECH License.
IMDAHARMONICS (Harmonics) plots the signal amplitude at the fundamental line frequency and its harmonics and measures the RMS amplitude and Total Harmonic Distortion of the signal. Requires a IMDA-MECH License.
IMDAMECHPWR (Mechanical Power) measures the mechanical power of the motor drive system. It is determined by the Speed and Torque. It is measured in watts. Requires a IMDA-MECH License.
IMDAPOWERQUALITY (Power Quality) measures the Frequency and RMS values of the voltage and current, Crest Factors of the voltage and current, True Power (PTRUE), Reactive Power (PRE), Apparent Power (PAPP), Power Factor, and Phase Angle (θ) of the AC signal. Requires a IMDA-MECH License.
IMDASPEED (Speed) measures the speed and acceleration. Requires a IMDA-MECH License.
IMDASYSEFF (System Efficiency) measures the total efficiency of the motor drive system. Requires a IMDA-MECH License.
IMDATORQUE (Torque) measures the torque of the motor. Configure Sensor (analog) or Current method to measure the torque. Requires a IMDA-MECH License.
ISI (Inter Symbol Interference) is defined as the range (difference between the maximum and minimum value) of DDJ-per-edge values appearing across all rising edges, or the range of DDJ-per-edge values across all falling edges, whichever is greater.
JITTERSUMMARY (Jitter Summary) is a group consisting of the following measurements: Data Rate, Pattern Length, TIE, TJ@BER, RJ, DJ, DJ-δδ, PJ, DDJ, DCD, ISI, and Eye Width@BER and RJ-δδ. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
J2 is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
J9 is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
LOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NPJ (non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIDTH (Negative Pulse Width) is the time the signal remains below the Mid reference level (R.
OBW (Occupied Bandwidth) refers to the bandwidth, including energy of a certain proportion of the total transmitted power, with the center frequency of the specified channel as the center.
PATTERNLENGTH (Pattern Length) is the number of symbols that constitute onefull repetition of a sequence within a signal. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PHASENOISE (Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.
PJ (periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
QFACTOR (Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RJ (random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RJDIRAC (dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SRJ (sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCFREQDEV (SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCMODRATE (SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCSLEWRATE (SSC Slew Rate) is the rate of change of the modulating frequencyof a spread spectrum clock. This measurement is made on each cycle in therecord. This measurement requires the DJA option and is not available on a 4Series MSO instrument.
SETUP (Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.
SKEW Skew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.
TIE (time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.
TIMETOMAX Time to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.
TIMETOMIN Time to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.
TJBER (total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TNTRATIO T/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
UNITINTERVAL (Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.
VDIFFXOVR (Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WBGDDT (d/dt) measures the rate of change of voltage or current (slew rate) from the configured start level to the stop level. Requires a WBG-DPT License.
WBGDIODEDDT (Diode d/dt) measures the rate of change of voltage or current (slew rate) during the specified start and stop integration levels. Diode d/dt can be measured during rising or falling edge. Requires a WBG-DPT License.
WBGEOFF (Eoff) measures the energy dissipated in the Power Device during off region using the configured levels. Requires a WBG-DPT License.
WBGEON (Eon) measures the energy dissipated in the Power Device during on region using the configured levels. Requires a WBG-DPT License.
WBGERR (Err) measures the reverse recovery energy dissipated in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGIPEAK (Ipeak) measures the peak current of the Power Device in the on region. Requires a WBG-DPT License.
WBGIRRM (Irrm) measures the maximum current dissipated in the Power Device in the reverse recovery region. Requires a WBG-DPT License.
WBGQOSS (Qoss) is the charge that must be supplied to the output capacitance of the power device during a specified time interval. Requires a WBG-DPT License.
WBGQRR (Qrr) measures the reverse recovery charge in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDOFF (Td(off)) measures the turn off delay time of the Power Device in the off region using the configured levels. Requires a WBG-DPT License.
WBGTDON (Td(on)) measures the turn on delay time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTF (Tf) measures the fall time of the Power Device in the off region using the configured levels.
WBGTOFF (Toff) measures the turn off time of the Power Device. It is the sum of the turn off delay time and the fall time. Requires a WBG-DPT License.
WBGTON (Ton) measures the turn on time of the Power Device. It is the sum of the turn on delay time and the rise time. Requires a WBG-DPT License.
WBGTR (Tr) measures the rise time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTRR (Trr) measures the reverse recovery time of the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDT (Tdt) the time delay between turn on time of the high side MOSFET and turn on time of the low side MOSFET during the simultaneous switching. Requires a WBG-DPT License.
WBGVPEAK (Vpeak) measures the peak voltage of the Power Device in the off region. Requires a WBG-DPT License.
WIDTH (Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WIDTHBER (Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.

addnew `property` ¶

addnew: MeasurementAddnew

Return the MEASUrement:ADDNew command.

Description

This command adds the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDNew value command.

SCPI Syntax

- MEASUrement:ADDNew <QString>

Info

<QString> is the measurement to add. The argument is of the form ‘MEAS’ where NR1 ≥ 1.

annotate `property` ¶

annotate: MeasurementAnnotate

Return the MEASUrement:ANNOTate command.

Description

This command sets or queries the annotation state for measurements.

Usage

Using the .query() method will send the MEASUrement:ANNOTate? query.
Using the .verify(value) method will send the MEASUrement:ANNOTate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:ANNOTate value command.

SCPI Syntax

- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?

Info

OFF turns off measurement annotations.
AUTO turns on visible measurement annotations.

autoset `property` ¶

autoset: MeasurementAutoset

Return the MEASUrement:AUTOset command.

Description

This command performs a specified autoset.

Usage

Using the .write(value) method will send the MEASUrement:AUTOset value command.

SCPI Syntax

- MEASUrement:AUTOset {DPMAutoset|DPMPReset|EXECute|THREEPHASEAUTOset|WBGDeskewexec|WBGPREset|WBGGSTIM}

Info

DPMAutoset performs a power rail autoset operation. Requires a DPM license.
DPMPReset performs a power rail preset operation. Requires a DPM license.
EXECute performs an analysis jitter autoset.
THREEPHASEAUTOset performs an IMDA 3 phase autoset.
WBGDeskewexec performs WBG deskew on specific measurements. Requires a WBG-DPT license.
WBGPREset performs a measurement specific preset. Requires a WBG-DPT license.
WBGGSTIM performs gate stimulus forWBG measurement. Requires aWBG-DPT license.

ch `property` ¶

ch: dict[int, MeasurementChannel]

Return the MEASUrement:CH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>? query.
Using the .verify(value) method will send the MEASUrement:CH<x>? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.reflevels: The MEASUrement:CH<x>:REFLevels command tree.

clockrecovery `property` ¶

clockrecovery: MeasurementClockrecovery

Return the MEASUrement:CLOCKRecovery command tree.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.advanced: The MEASUrement:CLOCKRecovery:ADVanced command tree.
.clockfrequency: The MEASUrement:CLOCKRecovery:CLOCKFrequency command.
.clockmultiplier: The MEASUrement:CLOCKRecovery:CLOCKMultiplier command.
.constclockmode: The MEASUrement:CLOCKRecovery:CONSTCLOCKMODe command.
.damping: The MEASUrement:CLOCKRecovery:DAMPing command.
.datapath: The MEASUrement:CLOCKRecovery:DATAPath command.
.datarate: The MEASUrement:CLOCKRecovery:DATARate command.
.explicitclockmode: The MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe command.
.jtfbandwidth: The MEASUrement:CLOCKRecovery:JTFBandwidth command.
.loopbandwidth: The MEASUrement:CLOCKRecovery:LOOPBandwidth command.
.meanautocalculate: The MEASUrement:CLOCKRecovery:MEANAUTOCalculate command.
.method: The MEASUrement:CLOCKRecovery:METHod command.
.model: The MEASUrement:CLOCKRecovery:MODel command.
.nominaloffset: The MEASUrement:CLOCKRecovery:NOMINALOFFset command.
.standard: The MEASUrement:CLOCKRecovery:STAndard command.
.tdcompensation: The MEASUrement:CLOCKRecovery:TDCOMPensation command.

ddjmethod `property` ¶

ddjmethod: MeasurementDdjmethod

Return the MEASUrement:DDJMethod command.

Description

This command sets or queries the model used to separate-out DDJ from TIE.

Usage

Using the .query() method will send the MEASUrement:DDJMethod? query.
Using the .verify(value) method will send the MEASUrement:DDJMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:DDJMethod value command.

SCPI Syntax

- MEASUrement:DDJMethod {SPECtraldomain|TIMDomain}
- MEASUrement:DDJMethod?

delete `property` ¶

delete: MeasurementDelete

Return the MEASUrement:DELete command.

Description

The command deletes the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:DELete value command.

SCPI Syntax

- MEASUrement:DELete <QString>

Info

<QString> is the measurement to delete. Argument is of the form ‘MEAS’ where is ≥1.

deleteall `property` ¶

deleteall: MeasurementDeleteall

Return the MEASUrement:DELETEALL command.

Description

This command deletes all the active instances of measurements defined in the scope application.

Usage

Using the .write() method will send the MEASUrement:DELETEALL command.

SCPI Syntax

- MEASUrement:DELETEALL

diracmodel `property` ¶

diracmodel: MeasurementDiracmodel

Return the MEASUrement:DIRacmodel command.

Description

This command sets or queries the dirac model used to separate random from deterministic jitter for jitter measurements.

Usage

Using the .query() method will send the MEASUrement:DIRacmodel? query.
Using the .verify(value) method will send the MEASUrement:DIRacmodel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:DIRacmodel value command.

SCPI Syntax

- MEASUrement:DIRacmodel {PCIExpress|FIBREchannel}
- MEASUrement:DIRacmodel?

Info

PCIExpress specifies the PCIExpress dirac model.
FIBREchannel specifies the FIBREchannel dirac model.

displayunits `property` ¶

displayunits: MeasurementDisplayunits

Return the MEASUrement:DISPLAYUnits command.

Description

This command sets or queries the display units used for jitter summary measurements.

Usage

Using the .query() method will send the MEASUrement:DISPLAYUnits? query.
Using the .verify(value) method will send the MEASUrement:DISPLAYUnits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:DISPLAYUnits value command.

SCPI Syntax

- MEASUrement:DISPLAYUnits {SEConds|UNITINtervals}
- MEASUrement:DISPLAYUnits?

Info

SEConds set the display units to seconds.
UNITINtervals set the display units to unit intervals.

edge `property` ¶

edge: dict[int, MeasurementEdgeItem]

Return the MEASUrement:EDGE<x> command.

Description

This command sets or queries the type of the edge for the measurement.

Usage

Using the .query() method will send the MEASUrement:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:EDGE<x> value command.

SCPI Syntax

- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:EDGE<x>?

Info

FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.

enablepjitter `property` ¶

enablepjitter: MeasurementEnablepjitter

Return the MEASUrement:ENABLEPjitter command.

Description

This command sets or queries the state of period jitter analysis mode.

Usage

Using the .query() method will send the MEASUrement:ENABLEPjitter? query.
Using the .verify(value) method will send the MEASUrement:ENABLEPjitter? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:ENABLEPjitter value command.

SCPI Syntax

- MEASUrement:ENABLEPjitter {ON|OFF|1|0}
- MEASUrement:ENABLEPjitter?

Info

ON indicates that period jitter analysis mode is active.
OFF indicates that period jitter analysis mode is off.
1 turns on period jitter analysis mode. Any number value other than 0 will turn period jitter analysis mode on.
0 turns off period jitter analysis mode.

eyerender `property` ¶

eyerender: MeasurementEyerender

Return the MEASUrement:EYERENDER command.

Description

This command sets or queries the state of high-performance eye rendering for an eye diagram.

Usage

Using the .query() method will send the MEASUrement:EYERENDER? query.
Using the .verify(value) method will send the MEASUrement:EYERENDER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:EYERENDER value command.

SCPI Syntax

- MEASUrement:EYERENDER {ON|OFF|<NR1>}
- MEASUrement:EYERENDER?

Info

<NR1> = 0 disables high-performance eye rendering for an eye diagram; any other value turns this feature on.
OFF disables high-performance eye rendering for an eye diagram.
ON enables high-performance eye rendering for an eye diagram.

filters `property` ¶

filters: MeasurementFilters

Return the MEASUrement:FILTers command tree.

Usage

Using the .query() method will send the MEASUrement:FILTers? query.
Using the .verify(value) method will send the MEASUrement:FILTers? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.blankingtime: The MEASUrement:FILTers:BLANKingtime command.
.highpass: The MEASUrement:FILTers:HIGHPass command tree.
.lowpass: The MEASUrement:FILTers:LOWPass command tree.
.ramptime: The MEASUrement:FILTers:RAMPtime command.

gating `property` ¶

gating: MeasurementGating

Return the MEASUrement:GATing command.

Description

This command sets or queries the global gating type for the measurement.

Usage

Using the .query() method will send the MEASUrement:GATing? query.
Using the .verify(value) method will send the MEASUrement:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing value command.

SCPI Syntax

- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing?

Info

NONE turns off measurement gating.
SCREEN turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only on the portion of the waveform where the logic source is in the active state.
SEARCH specifies that measurements are taken based on search criteria.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Sub-properties

.active: The MEASUrement:GATing:ACTive command.
.endtime: The MEASUrement:GATing:ENDtime command.
.hysteresis: The MEASUrement:GATing:HYSTeresis command.
.logicsource: The MEASUrement:GATing:LOGICSource command.
.midref: The MEASUrement:GATing:MIDRef command.
.searchsource: The MEASUrement:GATing:SEARCHSource command.
.starttime: The MEASUrement:GATing:STARTtime command.

highlevel `property` ¶

highlevel: MeasurementHighlevel

Return the MEASUrement:HIGHLEVel command tree.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.configuration: The MEASUrement:HIGHLEVel:CONFIGuration command.
.edgequalifier: The MEASUrement:HIGHLEVel:EDGEQUALifier command.
.inlowpass: The MEASUrement:HIGHLEVel:INLOWPass command tree.
.l2ltol2n: The MEASUrement:HIGHLEVel:L2LTOL2N command.
.lineselected: The MEASUrement:HIGHLEVel:LINESelected command.
.outedgequalifier: The MEASUrement:HIGHLEVel:OUTEDGEQUALifier command.
.outl2ltol2n: The MEASUrement:HIGHLEVel:OUTL2LTOL2N command.
.outlineselected: The MEASUrement:HIGHLEVel:OUTLINESelected command.
.outlowpass: The MEASUrement:HIGHLEVel:OUTLOWPass command tree.
.outsource: The MEASUrement:HIGHLEVel:OUTSOURCE command.
.outwiring: The MEASUrement:HIGHLEVel:OUTWIRing command.
.source: The MEASUrement:HIGHLEVel:SOURCE command.
.wiring: The MEASUrement:HIGHLEVel:WIRing command.

interp `property` ¶

interp: MeasurementInterp

Return the MEASUrement:INTERp command.

Description

This command sets or queries the interpolation mode used to locate edge crossings.

Usage

Using the .query() method will send the MEASUrement:INTERp? query.
Using the .verify(value) method will send the MEASUrement:INTERp? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:INTERp value command.

SCPI Syntax

- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?

Info

AUTO automatically selects the interpolation mode.
SINX specifies sin(x)/x interpolation, where acquired points are fit to a curve.
LINear specifies linear interpolation, where acquired points are connected with straight lines.

jittermodel `property` ¶

jittermodel: MeasurementJittermodel

Return the MEASUrement:JITTermodel command.

Description

This command sets or queries the model used to separate random from deterministic jitter for jitter measurements.

Usage

Using the .query() method will send the MEASUrement:JITTermodel? query.
Using the .verify(value) method will send the MEASUrement:JITTermodel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:JITTermodel value command.

SCPI Syntax

- MEASUrement:JITTermodel {SPECTRAL|SPECTRALBUJ}
- MEASUrement:JITTermodel?

Info

SPECTRAL sets the jitter separation model to spectral only.
SPECTRALBUJ sets the jitter separation model to spectral plus BUJ.

list `property` ¶

list: MeasurementList

Return the MEASUrement:LIST command.

Description

This query returns a comma separated list of all currently defined measurements.

Usage

Using the .query() method will send the MEASUrement:LIST? query.
Using the .verify(value) method will send the MEASUrement:LIST? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:LIST?

lockrj `property` ¶

lockrj: MeasurementLockrj

Return the MEASUrement:LOCKRJ command.

Description

This command sets or queries the state of RJ locking.

Usage

Using the .query() method will send the MEASUrement:LOCKRJ? query.
Using the .verify(value) method will send the MEASUrement:LOCKRJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:LOCKRJ value command.

SCPI Syntax

- MEASUrement:LOCKRJ {ON|OFF|1|0}
- MEASUrement:LOCKRJ?

Info

ON indicates that RJ locking is active.
OFF indicates that RJ locking is off.
1 turns on RJ locking. Any number value other than 0 will turn RJ locking on.
0 turns off RJ locking.

lockrjvalue `property` ¶

lockrjvalue: MeasurementLockrjvalue

Return the MEASUrement:LOCKRJValue command.

Description

This command sets or queries the RJ lock value.

Usage

Using the .query() method will send the MEASUrement:LOCKRJValue? query.
Using the .verify(value) method will send the MEASUrement:LOCKRJValue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:LOCKRJValue value command.

SCPI Syntax

- MEASUrement:LOCKRJValue <NR3>
- MEASUrement:LOCKRJValue?

Info

<NR3> default value = 1e-12; minimum value = 1e-15; maximum value = 1.

math `property` ¶

math: dict[int, MeasurementMathItem]

Return the MEASUrement:MATH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.reflevels: The MEASUrement:MATH<x>:REFLevels command tree.

meas `property` ¶

meas: dict[int, MeasurementMeasItem]

Return the MEASUrement:MEAS<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.abandwidth: The MEASUrement:MEAS<x>:ABANdwidth command.
.achannels: The MEASUrement:MEAS<x>:ACHANnels command.
.amethod: The MEASUrement:MEAS<x>:AMEThod command.
.bcount: The MEASUrement:MEAS<x>:BCOunt command.
.bdelay: The MEASUrement:MEAS<x>:BDELay command.
.ber: The MEASUrement:MEAS<x>:BER command.
.bin: The MEASUrement:MEAS<x>:BIN command.
.bitabsolute: The MEASUrement:MEAS<x>:BITAbsolute command.
.bitcfgmode: The MEASUrement:MEAS<x>:BITCfgmode command.
.bitend: The MEASUrement:MEAS<x>:BITEnd command.
.bitpcnt: The MEASUrement:MEAS<x>:BITPcnt command.
.bitstart: The MEASUrement:MEAS<x>:BITSTart command.
.bittype: The MEASUrement:MEAS<x>:BITType command.
.bmtype: The MEASUrement:MEAS<x>:BMTYPe command.
.burstedgtype: The MEASUrement:MEAS<x>:BURSTEDGTYPe command.
.bvoltage: The MEASUrement:MEAS<x>:BVOLTage command.
.ccresults: The MEASUrement:MEAS<x>:CCRESUlts command tree.
.cfval: The MEASUrement:MEAS<x>:CF<x>Val command.
.clockrecovery: The MEASUrement:MEAS<x>:CLOCKRecovery command tree.
.commonmode: The MEASUrement:MEAS<x>:COMMONMode command tree.
.cover: The MEASUrement:MEAS<x>:COVer command.
.cpwidth: The MEASUrement:MEAS<x>:CPWIDTh command.
.cspacing: The MEASUrement:MEAS<x>:CSPACing command.
.customlimitsfile: The MEASUrement:MEAS<x>:CUSTOMLIMITSFile command.
.cyclemode: The MEASUrement:MEAS<x>:CYCLemode command.
.dbdown: The MEASUrement:MEAS<x>:DBDown command.
.delay: The MEASUrement:MEAS<x>:DELay command tree.
.displaystat: The MEASUrement:MEAS<x>:DISPlaystat command tree.
.dmethod: The MEASUrement:MEAS<x>:DMEThod command.
.dvds: The MEASUrement:MEAS<x>:DVDS command.
.edge: The MEASUrement:MEAS<x>:EDGE<x> command.
.edgeincre: The MEASUrement:MEAS<x>:EDGEIncre command.
.edgequalone: The MEASUrement:MEAS<x>:EDGEQUALONE command.
.edgequaltwo: The MEASUrement:MEAS<x>:EDGEQUALTWO command.
.edgequalifier: The MEASUrement:MEAS<x>:EDGEQUALifier command.
.edges: The MEASUrement:MEAS<x>:EDGES command tree.
.eequal: The MEASUrement:MEAS<x>:EEQUal command.
.einductance: The MEASUrement:MEAS<x>:EINDuctance command.
.einterpolation: The MEASUrement:MEAS<x>:EINTerpolation command.
.extenduis: The MEASUrement:MEAS<x>:EXTENDuis command.
.eyerender: The MEASUrement:MEAS<x>:EYERender command.
.failcount: The MEASUrement:MEAS<x>:FAILCount command.
.fcount: The MEASUrement:MEAS<x>:FCOunt command.
.filterrangefrom: The MEASUrement:MEAS<x>:FILTERRANGEFROM command.
.filterrangeto: The MEASUrement:MEAS<x>:FILTERRANGETO command.
.filters: The MEASUrement:MEAS<x>:FILTers command tree.
.forder: The MEASUrement:MEAS<x>:FORDer command.
.fparameter: The MEASUrement:MEAS<x>:FPARAmeter command.
.freq: The MEASUrement:MEAS<x>:FREQ command.
.fromedgesearchdirect: The MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.
.fromsymbol: The MEASUrement:MEAS<x>:FROMSymbol command tree.
.fromedge: The MEASUrement:MEAS<x>:FROMedge command.
.ftype: The MEASUrement:MEAS<x>:FTYPe command.
.fundcurrent: The MEASUrement:MEAS<x>:FUNDCURRent command.
.gating: The MEASUrement:MEAS<x>:GATing command.
.globalref: The MEASUrement:MEAS<x>:GLOBalref command.
.harmonicsclass: The MEASUrement:MEAS<x>:HARMONICSCLass command.
.harmonicssource: The MEASUrement:MEAS<x>:HARMONICSSOURce command.
.harmonicsstd: The MEASUrement:MEAS<x>:HARMONICSStd command.
.harmonicsunits: The MEASUrement:MEAS<x>:HARMONICSUNits command.
.highlevel: The MEASUrement:MEAS<x>:HIGHLEVel command tree.
.highrefvoltage: The MEASUrement:MEAS<x>:HIGHREFVoltage command.
.hlevel: The MEASUrement:MEAS<x>:HLEVel command tree.
.htorque: The MEASUrement:MEAS<x>:HTORque command.
.hvoltage: The MEASUrement:MEAS<x>:HVOLtage command.
.idletime: The MEASUrement:MEAS<x>:IDLETime command.
.inputlevel: The MEASUrement:MEAS<x>:INPUTLEVel command.
.inputpower: The MEASUrement:MEAS<x>:INPUTPOwer command.
.jittersummary: The MEASUrement:MEAS<x>:JITTERSummary command tree.
.label: The MEASUrement:MEAS<x>:LABel command.
.lineselected: The MEASUrement:MEAS<x>:LINESelected command.
.lowrefvoltage: The MEASUrement:MEAS<x>:LOWREFVoltage command.
.ltorque: The MEASUrement:MEAS<x>:LTORque command.
.ltype: The MEASUrement:MEAS<x>:LTYPe command.
.lunits: The MEASUrement:MEAS<x>:LUNITs command.
.lvoltage: The MEASUrement:MEAS<x>:LVOLtage command.
.matime: The MEASUrement:MEAS<x>:MATime command.
.maxcurrent: The MEASUrement:MEAS<x>:MAXCUrrent command.
.maxcycle: The MEASUrement:MEAS<x>:MAXCycle command.
.maxg1voltage: The MEASUrement:MEAS<x>:MAXG1Voltage command.
.maxg2voltage: The MEASUrement:MEAS<x>:MAXG2Voltage command.
.maxgvoltage: The MEASUrement:MEAS<x>:MAXGVoltage command.
.maxvoltage: The MEASUrement:MEAS<x>:MAXVoltage command.
.measrange: The MEASUrement:MEAS<x>:MEASRange command tree.
.mech: The MEASUrement:MEAS<x>:MECH command tree.
.mincycle: The MEASUrement:MEAS<x>:MINCycle command.
.nvalue: The MEASUrement:MEAS<x>:NVALUe command.
.obwmethod: The MEASUrement:MEAS<x>:OBWMethod command.
.oddeven: The MEASUrement:MEAS<x>:ODDEVen command.
.ofilters: The MEASUrement:MEAS<x>:OFILters command tree.
.osangle: The MEASUrement:MEAS<x>:OSANgle command.
.outedgequalifier: The MEASUrement:MEAS<x>:OUTEDGEQUALifier command.
.outfilters: The MEASUrement:MEAS<x>:OUTFILTers command tree.
.outputvoltage: The MEASUrement:MEAS<x>:OUTPUT<x>VOLTage command.
.passfailenabled: The MEASUrement:MEAS<x>:PASSFAILENabled command.
.passfailhighlimit: The MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.
.passfaillimit: The MEASUrement:MEAS<x>:PASSFAILLIMit command.
.passfaillowlimit: The MEASUrement:MEAS<x>:PASSFAILLOWlimit command.
.passfailmargin: The MEASUrement:MEAS<x>:PASSFAILMARgin command.
.passfailwhen: The MEASUrement:MEAS<x>:PASSFAILWHEN command.
.patterndetection: The MEASUrement:MEAS<x>:PATTERNDETECTION command.
.patternlength: The MEASUrement:MEAS<x>:PATTERNLENgth command.
.patterntype: The MEASUrement:MEAS<x>:PATTERNTYPe command.
.pcount: The MEASUrement:MEAS<x>:PCOUNt command.
.perfreq: The MEASUrement:MEAS<x>:PERFREQ command tree.
.pfrequency: The MEASUrement:MEAS<x>:PFREquency command.
.polarity: The MEASUrement:MEAS<x>:POLarity command.
.population: The MEASUrement:MEAS<x>:POPUlation command tree.
.popower: The MEASUrement:MEAS<x>:POPower command.
.powerfactor: The MEASUrement:MEAS<x>:POWERFACtor command.
.pregion: The MEASUrement:MEAS<x>:PREGion command.
.presistance: The MEASUrement:MEAS<x>:PRESistance command.
.pthreshold: The MEASUrement:MEAS<x>:PTHReshold command.
.pwidth: The MEASUrement:MEAS<x>:PWIDth command.
.redge: The MEASUrement:MEAS<x>:REDGe command.
.reflevels: The MEASUrement:MEAS<x>:REFLevels command tree.
.reflevels1: The MEASUrement:MEAS<x>:REFLevels1 command tree.
.refmode: The MEASUrement:MEAS<x>:REFMode command.
.refvoltageval: The MEASUrement:MEAS<x>:REFVOLTAGE<x>Val command.
.refvoltage: The MEASUrement:MEAS<x>:REFVoltage command.
.results: The MEASUrement:MEAS<x>:RESUlts command tree.
.rfrequency: The MEASUrement:MEAS<x>:RFREquency command.
.ripplefreqval: The MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val command.
.rrange: The MEASUrement:MEAS<x>:RRANGE command.
.sequence: The MEASUrement:MEAS<x>:SEQuence command.
.signalfrequency: The MEASUrement:MEAS<x>:SIGNALFREQUEncy command.
.signaltype: The MEASUrement:MEAS<x>:SIGNALType command.
.slabs: The MEASUrement:MEAS<x>:SLABs command.
.slpct: The MEASUrement:MEAS<x>:SLPCt command.
.sltype: The MEASUrement:MEAS<x>:SLTYpe command.
.smoothingfilter: The MEASUrement:MEAS<x>:SMOOTHINGFILTER command.
.source: The MEASUrement:MEAS<x>:SOURCE command.
.source1: The MEASUrement:MEAS<x>:SOUrce1 command.
.spanval: The MEASUrement:MEAS<x>:SPAN<x>Val command.
.srate: The MEASUrement:MEAS<x>:SRATe command.
.srho: The MEASUrement:MEAS<x>:SRHo command.
.ssc: The MEASUrement:MEAS<x>:SSC command tree.
.ssdirection: The MEASUrement:MEAS<x>:SSDirection command.
.status: The MEASUrement:MEAS<x>:STATUS command.
.stlabs: The MEASUrement:MEAS<x>:STLABs command.
.stlpct: The MEASUrement:MEAS<x>:STLPct command.
.stltype: The MEASUrement:MEAS<x>:STLTYpe command.
.stsdirection: The MEASUrement:MEAS<x>:STSDirection command.
.stype: The MEASUrement:MEAS<x>:STYPe command.
.subgroup: The MEASUrement:MEAS<x>:SUBGROUP command tree.
.sunits: The MEASUrement:MEAS<x>:SUNits command.
.tckavg: The MEASUrement:MEAS<x>:TCKAVG command.
.tconstant: The MEASUrement:MEAS<x>:TCONstant command.
.tdrpreset: The MEASUrement:MEAS<x>:TDRPreset command.
.timingmode: The MEASUrement:MEAS<x>:TIMINGMode command.
.tlevel: The MEASUrement:MEAS<x>:TLEVel command.
.tmethod: The MEASUrement:MEAS<x>:TMEThod command.
.toedgesearchdirect: The MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.
.toedge: The MEASUrement:MEAS<x>:TOEdge command.
.tosymbol: The MEASUrement:MEAS<x>:TOSYmbol command tree.
.transition: The MEASUrement:MEAS<x>:TRANSition command.
.type: The MEASUrement:MEAS<x>:TYPe command.
.vlevel: The MEASUrement:MEAS<x>:VLEVel command.
.waittime: The MEASUrement:MEAS<x>:WAITTime command.
.wbg: The MEASUrement:MEAS<x>:WBG command tree.
.width: The MEASUrement:MEAS<x>:WIDTh command.
.windowlength: The MEASUrement:MEAS<x>:WINDOWLENgth command.
.xunit: The MEASUrement:MEAS<x>:XUNIT command.
.yunit: The MEASUrement:MEAS<x>:YUNIT command.

measrange `property` ¶

measrange: MeasurementMeasrange

Return the MEASUrement:MEASRange command tree.

Usage

Using the .query() method will send the MEASUrement:MEASRange? query.
Using the .verify(value) method will send the MEASUrement:MEASRange? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.max: The MEASUrement:MEASRange:MAX command.
.min: The MEASUrement:MEASRange:MIN command.
.state: The MEASUrement:MEASRange:STATE command.

mech `property` ¶

mech: MeasurementMech

Return the MEASUrement:MECH command tree.

Usage

Using the .query() method will send the MEASUrement:MECH? query.
Using the .verify(value) method will send the MEASUrement:MECH? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.eindexz: The MEASUrement:MECH:EINDexz command.
.gratio: The MEASUrement:MECH:GRATio command.
.munits: The MEASUrement:MECH:MUNits command.
.ppairs: The MEASUrement:MECH:PPAirs command.
.pprotation: The MEASUrement:MECH:PPRotation command.
.source1: The MEASUrement:MECH:SOUrce1 command.
.stype: The MEASUrement:MECH:STYPe command.

minui `property` ¶

minui: MeasurementMinui

Return the MEASUrement:MINUI command.

Description

This command sets or queries the minimum number of unit intervals required for BUJ analysis.

Usage

Using the .query() method will send the MEASUrement:MINUI? query.
Using the .verify(value) method will send the MEASUrement:MINUI? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MINUI value command.

SCPI Syntax

- MEASUrement:MINUI <NR3>
- MEASUrement:MINUI?

Info

<NR3> is the minimum number of unit intervals required for BUJ analysis.

population `property` ¶

population: MeasurementPopulation

Return the MEASUrement:POPUlation command tree.

Usage

Using the .query() method will send the MEASUrement:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:POPUlation? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.limit: The MEASUrement:POPUlation:LIMIT command tree.

ref `property` ¶

ref: dict[int, MeasurementRefItem]

Return the MEASUrement:REF<x> command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>? query.
Using the .verify(value) method will send the MEASUrement:REF<x>? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.reflevels: The MEASUrement:REF<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementReflevels

Return the MEASUrement:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REFLevels? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.absolute: The MEASUrement:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REFLevels:BASETop command.
.jittermode: The MEASUrement:REFLevels:JITTERMODE command.
.method: The MEASUrement:REFLevels:METHod command.
.mode: The MEASUrement:REFLevels:MODE command.
.percent: The MEASUrement:REFLevels:PERCent command tree.
.type: The MEASUrement:REFLevels:TYPE command.

results `property` ¶

results: MeasurementResults

Return the MEASUrement:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:RESUlts? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.history: The MEASUrement:RESUlts:HISTory command tree.

statistics `property` ¶

statistics: MeasurementStatistics

Return the MEASUrement:STATIstics command tree.

Usage

Using the .query() method will send the MEASUrement:STATIstics? query.
Using the .verify(value) method will send the MEASUrement:STATIstics? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.cyclemode: The MEASUrement:STATIstics:CYCLEMode command.

wbg `property` ¶

wbg: MeasurementWbg

Return the MEASUrement:WBG command tree.

Usage

Using the .query() method will send the MEASUrement:WBG? query.
Using the .verify(value) method will send the MEASUrement:WBG? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.pdevice: The MEASUrement:WBG:PDEVice command.

MeasurementAddmeas ¶

Bases: SCPICmdWrite

The MEASUrement:ADDMEAS command.

Description

This command adds a measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDMEAS value command.

SCPI Syntax

- MEASUrement:ADDMEAS {ACCOMMONMODE|ACPR|ACRMS|AMPLITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|CCJITTER|COMMONMODE|CPOWER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMPSIJ|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HEIGHT|HEIGHTBER|HIGH|HIGHTIME|HOLD|IMDAANGLE|IMDADIRECTION|IMDADQ0|IMDAEFFICIENCY|IMDAHARMONICS|IMDAMECHPWR|IMDAPOWERQUALITY|IMDASPEED|IMDASYSEFF|IMDATORQUE|ISI|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUty|NOVERSHOOT|NPERIOD|NPJ|NWIDTH|OBW|PATTERNLENGTH|PDUTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SETUP|SKEW|SRJ|SSCFREQDEV|SSCMODRATE|SSCSLEWRATE|TIE|TIMEOUTSIDELEVEL|TIMETOMAX|TIMETOMIN|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WBGDDT|WBGDIODEDDT|WBGEOFF|WBGEON|WBGERR|WBGIPEAK|WBGIRRM|WBGQOSS|WBGQRR|WBGTDOFF|WBGTDON|WBGTF|WBGTON|WBGTOFF|WBGTR|WBGTRR|WBGTDT|WBGVPEAK|WIDTH|WIDTHBER}

Info

ACCOMMONMODE AC Common Mode (Pk-Pk) is the peak-to-peak of the commonmode voltage of two sources. This measurement is made across the entire record.This measurement requires the DJA option and is not available on a 4 SeriesMSO instrument.
ACPR (Adjacent Channel Power Ratio) is the amount of power that leaks intoadjacent channels. This can be specified in terms of absolute power or a ratio ofadjacent channel power to the main channel power, called adjacent channel powerratio (ACPR) or adjacent channel leakage ratio (ACLR).
ACRMS (AC RMS) is the true Root Mean Square of the data points, about theMean. This measurement can be made across the entire record, or on each cyclein the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BITAMPLITUDE (Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITHIGH (Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITLOW (Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
CCJITTER (Cycle-to-Cycle jitter) measures how much the clock period changes between any two adjacent cycles. Cycle-to-Cycle jitter is measured by applying a first order difference operation to the period jitter.
COMMONMODE (DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
CPOWER (Channel Power) is the measurement of integrated power within a specified channel bandwidth for a RF signal. The resulting channel power is an absolute power measurement.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DCD (duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDJ (data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDRAOS (area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.
DDRAOSPERTCK (area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAOSPERUI (area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRAUS (area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.
DDRAUSPERTCK (area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAUSPERUI (area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRHOLDDIFF (hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.
DDRSETUPDIFF (setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.
DDRTCHABS (absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.
DDRTCHAVERAGE (average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCKAVERAGE (average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCLABS (absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.
DDRTCLAVERAGE (average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.
DDRTERRMN (cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).
DDRTERRN (cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).
DDRTJITCC (cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.
DDRTJITDUTY (half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.
DDRTJITPER (clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.
DDRTPST (read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.
DDRTRPRE (read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRTWPRE is the width of theWrite burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRVIXAC is the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.
DDRTDQSCK is the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
DJ (deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DJDIRAC (dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DPMPSIJ is the Power Supply Induced Jitter. This measurement helps in suppressing the jitter in high speed signals (victim) induced from power rail signals (aggressor).
EYEHIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
EYELOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
F2 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F4 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F8 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.
HEIGHT (Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HEIGHTBER (Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
IMDAANGLE (Angle) measures the phase angle. Configure QEI or Hall sensor to.
compute the angle measurement. Requires a IMDA-MECH License.
IMDADIRECTION (Direction) defines the direction of rotation of the motor. Set the direction A-B-C or A-C-B for Hall sensors and CW or CCW for QEI based on the motor configuration. Requires a IMDA-MECH License.
IMDADQ0 measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0. Requires a IMDA-MECH License.
IMDAEFFICIENCY (Efficiency) measures the ratio of sum of output power(s) to input power for respective input and output Voltage and Current pairs. Note: the current release cannot support 3V and 3I pairs, since this requires 12 channels. We restrict to 2V and 2I which needs 8 scope channels. Requires a IMDA-MECH License.
IMDAHARMONICS (Harmonics) plots the signal amplitude at the fundamental line frequency and its harmonics and measures the RMS amplitude and Total Harmonic Distortion of the signal. Requires a IMDA-MECH License.
IMDAMECHPWR (Mechanical Power) measures the mechanical power of the motor drive system. It is determined by the Speed and Torque. It is measured in watts. Requires a IMDA-MECH License.
IMDAPOWERQUALITY (Power Quality) measures the Frequency and RMS values of the voltage and current, Crest Factors of the voltage and current, True Power (PTRUE), Reactive Power (PRE), Apparent Power (PAPP), Power Factor, and Phase Angle (θ) of the AC signal. Requires a IMDA-MECH License.
IMDASPEED (Speed) measures the speed and acceleration. Requires a IMDA-MECH License.
IMDASYSEFF (System Efficiency) measures the total efficiency of the motor drive system. Requires a IMDA-MECH License.
IMDATORQUE (Torque) measures the torque of the motor. Configure Sensor (analog) or Current method to measure the torque. Requires a IMDA-MECH License.
ISI (Inter Symbol Interference) is defined as the range (difference between the maximum and minimum value) of DDJ-per-edge values appearing across all rising edges, or the range of DDJ-per-edge values across all falling edges, whichever is greater.
JITTERSUMMARY (Jitter Summary) is a group consisting of the following measurements: Data Rate, Pattern Length, TIE, TJ@BER, RJ, DJ, DJ-δδ, PJ, DDJ, DCD, ISI, and Eye Width@BER and RJ-δδ. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
J2 is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
J9 is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
LOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NPJ (non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIDTH (Negative Pulse Width) is the time the signal remains below the Mid reference level (R.
OBW (Occupied Bandwidth) refers to the bandwidth, including energy of a certain proportion of the total transmitted power, with the center frequency of the specified channel as the center.
PATTERNLENGTH (Pattern Length) is the number of symbols that constitute onefull repetition of a sequence within a signal. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PHASENOISE (Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.
PJ (periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
QFACTOR (Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RJ (random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RJDIRAC (dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SRJ (sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCFREQDEV (SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCMODRATE (SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCSLEWRATE (SSC Slew Rate) is the rate of change of the modulating frequencyof a spread spectrum clock. This measurement is made on each cycle in therecord. This measurement requires the DJA option and is not available on a 4Series MSO instrument.
SETUP (Setup Time) is the time between the specified Mid reference level (RM) crossing on the Data source to the closest specified Mid reference level (RM) crossing on the Clock source. This measurement is made on each specified Clock edge in the record.
SKEW Skew is the time between the specified Mid reference level (RM) crossing on one source to the following specified Mid reference level (RM) crossing on a second source. This measurement is made on each cycle in the record.
TIE (time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (RB). This measurement is made on each occurrence in the record.
TIMETOMAX Time to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.
TIMETOMIN Time to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.
TJBER (total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TNTRATIO T/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
UNITINTERVAL (Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.
VDIFFXOVR (Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WBGDDT (d/dt) measures the rate of change of voltage or current (slew rate) from the configured start level to the stop level. Requires a WBG-DPT License.
WBGDIODEDDT (Diode d/dt) measures the rate of change of voltage or current (slew rate) during the specified start and stop integration levels. Diode d/dt can be measured during rising or falling edge. Requires a WBG-DPT License.
WBGEOFF (Eoff) measures the energy dissipated in the Power Device during off region using the configured levels. Requires a WBG-DPT License.
WBGEON (Eon) measures the energy dissipated in the Power Device during on region using the configured levels. Requires a WBG-DPT License.
WBGERR (Err) measures the reverse recovery energy dissipated in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGIPEAK (Ipeak) measures the peak current of the Power Device in the on region. Requires a WBG-DPT License.
WBGIRRM (Irrm) measures the maximum current dissipated in the Power Device in the reverse recovery region. Requires a WBG-DPT License.
WBGQOSS (Qoss) is the charge that must be supplied to the output capacitance of the power device during a specified time interval. Requires a WBG-DPT License.
WBGQRR (Qrr) measures the reverse recovery charge in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDOFF (Td(off)) measures the turn off delay time of the Power Device in the off region using the configured levels. Requires a WBG-DPT License.
WBGTDON (Td(on)) measures the turn on delay time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTF (Tf) measures the fall time of the Power Device in the off region using the configured levels.
WBGTOFF (Toff) measures the turn off time of the Power Device. It is the sum of the turn off delay time and the fall time. Requires a WBG-DPT License.
WBGTON (Ton) measures the turn on time of the Power Device. It is the sum of the turn on delay time and the rise time. Requires a WBG-DPT License.
WBGTR (Tr) measures the rise time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTRR (Trr) measures the reverse recovery time of the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDT (Tdt) the time delay between turn on time of the high side MOSFET and turn on time of the low side MOSFET during the simultaneous switching. Requires a WBG-DPT License.
WBGVPEAK (Vpeak) measures the peak voltage of the Power Device in the off region. Requires a WBG-DPT License.
WIDTH (Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WIDTHBER (Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.

MeasurementAddnew ¶

Bases: SCPICmdWrite

The MEASUrement:ADDNew command.

Description

This command adds the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:ADDNew value command.

SCPI Syntax

- MEASUrement:ADDNew <QString>

Info

<QString> is the measurement to add. The argument is of the form ‘MEAS’ where NR1 ≥ 1.

MeasurementAnnotate ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:ANNOTate command.

Description

This command sets or queries the annotation state for measurements.

Usage

Using the .query() method will send the MEASUrement:ANNOTate? query.
Using the .verify(value) method will send the MEASUrement:ANNOTate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:ANNOTate value command.

SCPI Syntax

- MEASUrement:ANNOTate {OFF|AUTO}
- MEASUrement:ANNOTate?

Info

OFF turns off measurement annotations.
AUTO turns on visible measurement annotations.

MeasurementAutoset ¶

Bases: SCPICmdWrite

The MEASUrement:AUTOset command.

Description

This command performs a specified autoset.

Usage

Using the .write(value) method will send the MEASUrement:AUTOset value command.

SCPI Syntax

- MEASUrement:AUTOset {DPMAutoset|DPMPReset|EXECute|THREEPHASEAUTOset|WBGDeskewexec|WBGPREset|WBGGSTIM}

Info

DPMAutoset performs a power rail autoset operation. Requires a DPM license.
DPMPReset performs a power rail preset operation. Requires a DPM license.
EXECute performs an analysis jitter autoset.
THREEPHASEAUTOset performs an IMDA 3 phase autoset.
WBGDeskewexec performs WBG deskew on specific measurements. Requires a WBG-DPT license.
WBGPREset performs a measurement specific preset. Requires a WBG-DPT license.
WBGGSTIM performs gate stimulus forWBG measurement. Requires aWBG-DPT license.

MeasurementChannel ¶

Bases: ValidatedChannel, SCPICmdRead

The MEASUrement:CH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>? query.
Using the .verify(value) method will send the MEASUrement:CH<x>? query and raise an AssertionError if the returned value does not match value.

Properties

.reflevels: The MEASUrement:CH<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementChannelReflevels

Return the MEASUrement:CH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.absolute: The MEASUrement:CH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:CH<x>:REFLevels:BASETop command.
.method: The MEASUrement:CH<x>:REFLevels:METHod command.
.percent: The MEASUrement:CH<x>:REFLevels:PERCent command tree.

MeasurementChannelReflevels ¶

Bases: SCPICmdRead

The MEASUrement:CH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Properties

.absolute: The MEASUrement:CH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:CH<x>:REFLevels:BASETop command.
.method: The MEASUrement:CH<x>:REFLevels:METHod command.
.percent: The MEASUrement:CH<x>:REFLevels:PERCent command tree.

absolute `property` ¶

absolute: MeasurementChannelReflevelsAbsolute

Return the MEASUrement:CH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementChannelReflevelsBasetop

Return the MEASUrement:CH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

method `property` ¶

method: MeasurementChannelReflevelsMethod

Return the MEASUrement:CH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?

Info

PERCent specifies percent reference level units.
ABSolute specifies absolute reference level units.

percent `property` ¶

percent: MeasurementChannelReflevelsPercent

Return the MEASUrement:CH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

MeasurementChannelReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementChannelReflevelsAbsoluteFallhigh

Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh M <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

falllow `property` ¶

falllow: MeasurementChannelReflevelsAbsoluteFalllow

Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

fallmid `property` ¶

fallmid: MeasurementChannelReflevelsAbsoluteFallmid

Return the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the mid reference level used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

hysteresis `property` ¶

hysteresis: MeasurementChannelReflevelsAbsoluteHysteresis

Return the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the hysteresis value used for autoset.

risehigh `property` ¶

risehigh: MeasurementChannelReflevelsAbsoluteRisehigh

Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the high reference level of the rising edge when the source ref level method is set to absolute.

riselow `property` ¶

riselow: MeasurementChannelReflevelsAbsoluteRiselow

Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the low reference level of the rising edge when the source ref level method is set to absolute.

risemid `property` ¶

risemid: MeasurementChannelReflevelsAbsoluteRisemid

Return the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge when the source ref level method is set to absolute.

type `property` ¶

type: MeasurementChannelReflevelsAbsoluteType

Return the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the source. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute reference levels for the specified measurement channel are the same.
UNIQue specifies that the absolute reference levels for the specified measurement channel are not the same.

MeasurementChannelReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh M <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementChannelReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementChannelReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the mid reference level used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

MeasurementChannelReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the hysteresis value used for autoset.

MeasurementChannelReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the high reference level of the rising edge when the source ref level method is set to absolute.

MeasurementChannelReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the low reference level of the rising edge when the source ref level method is set to absolute.

MeasurementChannelReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the source ref level method is set to absolute. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge when the source ref level method is set to absolute.

MeasurementChannelReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the source. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:CH<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute reference levels for the specified measurement channel are the same.
UNIQue specifies that the absolute reference levels for the specified measurement channel are not the same.

MeasurementChannelReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:CH<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

MeasurementChannelReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:CH<x>:REFLevels:METHod?

Info

PERCent specifies percent reference level units.
ABSolute specifies absolute reference level units.

MeasurementChannelReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementChannelReflevelsPercentFallhigh

Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

falllow `property` ¶

falllow: MeasurementChannelReflevelsPercentFalllow

Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the low reference level when the measurement Ref level method is set to Percent.

fallmid `property` ¶

fallmid: MeasurementChannelReflevelsPercentFallmid

Return the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

hysteresis `property` ¶

hysteresis: MeasurementChannelReflevelsPercentHysteresis

Return the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementChannelReflevelsPercentRisehigh

Return the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

riselow `property` ¶

riselow: MeasurementChannelReflevelsPercentRiselow

Return the MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

risemid `property` ¶

risemid: MeasurementChannelReflevelsPercentRisemid

Return the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

type `property` ¶

type: MeasurementChannelReflevelsPercentType

Return the MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?

Info

TENNinety specifies reference levels at the 10 and 90% levels.
TWENtyeighty specifies reference levels at the 20 and 80% levels.
CUSTom specifies custom reference levels.

MeasurementChannelReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the low reference level when the measurement Ref level method is set to Percent.

MeasurementChannelReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the source ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the hysteresis value used for the autoset.

MeasurementChannelReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:CH<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementChannelReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The channel number is specified by x.

Usage

Using the .query() method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:CH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:CH<x>:REFLevels:PERCent:TYPE?

Info

TENNinety specifies reference levels at the 10 and 90% levels.
TWENtyeighty specifies reference levels at the 20 and 80% levels.
CUSTom specifies custom reference levels.

MeasurementClockrecovery ¶

Bases: SCPICmdRead

The MEASUrement:CLOCKRecovery command tree.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery? query and raise an AssertionError if the returned value does not match value.

Properties

.advanced: The MEASUrement:CLOCKRecovery:ADVanced command tree.
.clockfrequency: The MEASUrement:CLOCKRecovery:CLOCKFrequency command.
.clockmultiplier: The MEASUrement:CLOCKRecovery:CLOCKMultiplier command.
.constclockmode: The MEASUrement:CLOCKRecovery:CONSTCLOCKMODe command.
.damping: The MEASUrement:CLOCKRecovery:DAMPing command.
.datapath: The MEASUrement:CLOCKRecovery:DATAPath command.
.datarate: The MEASUrement:CLOCKRecovery:DATARate command.
.explicitclockmode: The MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe command.
.jtfbandwidth: The MEASUrement:CLOCKRecovery:JTFBandwidth command.
.loopbandwidth: The MEASUrement:CLOCKRecovery:LOOPBandwidth command.
.meanautocalculate: The MEASUrement:CLOCKRecovery:MEANAUTOCalculate command.
.method: The MEASUrement:CLOCKRecovery:METHod command.
.model: The MEASUrement:CLOCKRecovery:MODel command.
.nominaloffset: The MEASUrement:CLOCKRecovery:NOMINALOFFset command.
.standard: The MEASUrement:CLOCKRecovery:STAndard command.
.tdcompensation: The MEASUrement:CLOCKRecovery:TDCOMPensation command.

advanced `property` ¶

advanced: MeasurementClockrecoveryAdvanced

Return the MEASUrement:CLOCKRecovery:ADVanced command tree.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:ADVanced? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:ADVanced? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.method: The MEASUrement:CLOCKRecovery:ADVanced:METHod command.

clockfrequency `property` ¶

clockfrequency: MeasurementClockrecoveryClockfrequency

Return the MEASUrement:CLOCKRecovery:CLOCKFrequency command.

Description

This command sets or queries the global clock frequency used when fixed constant clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:CLOCKFrequency? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:CLOCKFrequency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:CLOCKFrequency value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:CLOCKRecovery:CLOCKFrequency?

Info

<NR3> is the global clock frequency used with Constant Clock - Fixed clock recovery method.

clockmultiplier `property` ¶

clockmultiplier: MeasurementClockrecoveryClockmultiplier

Return the MEASUrement:CLOCKRecovery:CLOCKMultiplier command.

Description

This command sets or queries the global clock multiplier used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:CLOCKMultiplier? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:CLOCKMultiplier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:CLOCKMultiplier value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:CLOCKRecovery:CLOCKMultiplier?

Info

<NR3> is the global clock multiplier.

constclockmode `property` ¶

constclockmode: MeasurementClockrecoveryConstclockmode

Return the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe command.

Description

This command sets or queries the global constant clock mode used when constant clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe?

Info

MEAN sets the constant clock mode to MEAN.
MEDian sets the constant clock mode to MEDian.
FIXed sets the constant clock mode to FIXed.

damping `property` ¶

damping: MeasurementClockrecoveryDamping

Return the MEASUrement:CLOCKRecovery:DAMPing command.

Description

This command sets or queries the global damping value used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:DAMPing? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:DAMPing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:DAMPing value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:CLOCKRecovery:DAMPing?

Info

<NR3> is the global clock recovery damping value.

datapath `property` ¶

datapath: MeasurementClockrecoveryDatapath

Return the MEASUrement:CLOCKRecovery:DATAPath command.

Description

This command sets or queries the global file containing the data pattern used when known data pattern clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:DATAPath? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:DATAPath? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:DATAPath value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:DATAPath <QString>
- MEASUrement:CLOCKRecovery:DATAPath?

Info

<QString> is the path and filename, in quotes, of the file containing the data pattern.

datarate `property` ¶

datarate: MeasurementClockrecoveryDatarate

Return the MEASUrement:CLOCKRecovery:DATARate command.

Description

This command sets or queries the global nominal data bit rate used when nominal data rate clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:DATARate? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:DATARate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:DATARate value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:DATARate <NR3>
- MEASUrement:CLOCKRecovery:DATARate?

Info

<NR3> is the global value for the Nominal data rate.

explicitclockmode `property` ¶

explicitclockmode: MeasurementClockrecoveryExplicitclockmode

Return the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe command.

Description

This command sets or queries the global explicit clock mode used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?

Info

EDGE sets the clock mode to clock edge.
PLL sets the clock mode to phase locked loop.

jtfbandwidth `property` ¶

jtfbandwidth: MeasurementClockrecoveryJtfbandwidth

Return the MEASUrement:CLOCKRecovery:JTFBandwidth command.

Description

This command sets or queries the global JTF bandwidth used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:JTFBandwidth? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:JTFBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:JTFBandwidth value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:CLOCKRecovery:JTFBandwidth?

Info

<NR3> is the global clock recovery JTF bandwidth.

loopbandwidth `property` ¶

loopbandwidth: MeasurementClockrecoveryLoopbandwidth

Return the MEASUrement:CLOCKRecovery:LOOPBandwidth command.

Description

This command sets or queries the global loop bandwidth used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:LOOPBandwidth? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:LOOPBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:LOOPBandwidth value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:CLOCKRecovery:LOOPBandwidth?

Info

<NR3> is the global loop bandwidth.

meanautocalculate `property` ¶

meanautocalculate: MeasurementClockrecoveryMeanautocalculate

Return the MEASUrement:CLOCKRecovery:MEANAUTOCalculate command.

Description

This command sets or queries how often the clock is calculated when constant clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:MEANAUTOCalculate? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:MEANAUTOCalculate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:MEANAUTOCalculate value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate?

Info

FIRST calculates the clock on the first acquisition.
EVERY calculates the clock on every acquisition.

method `property` ¶

method: MeasurementClockrecoveryMethod

Return the MEASUrement:CLOCKRecovery:METHod command.

Description

This command sets or queries the global clock recovery method for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:METHod? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:METHod value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:CLOCKRecovery:METHod?

Info

PLL specifies using the phase locked loop.
CONSTANTCLOCK specifies using a constant clock.
EXPLICITCLOCK specifies using an explicit clock.

model `property` ¶

model: MeasurementClockrecoveryModel

Return the MEASUrement:CLOCKRecovery:MODel command.

Description

This command sets or queries the global phase locked loop (PLL) clock recovery model used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:MODel? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:MODel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:MODel value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:MODel TYPE<x>
- MEASUrement:CLOCKRecovery:MODel?

Info

TYPE<x> sets PLL clock recovery to a PLL model type. Valid values are 1 or 2.

nominaloffset `property` ¶

nominaloffset: MeasurementClockrecoveryNominaloffset

Return the MEASUrement:CLOCKRecovery:NOMINALOFFset command.

Description

This command sets or queries the global offset value used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:CLOCKRecovery:NOMINALOFFset?

Info

<NR3> is the global clock offset.

Sub-properties

.selectiontype: The MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

standard `property` ¶

standard: MeasurementClockrecoveryStandard

Return the MEASUrement:CLOCKRecovery:STAndard command.

Description

This command sets or queries the global communications standard used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:STAndard? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:STAndard? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:STAndard value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:CLOCKRecovery:STAndard?

Info

CUSTom sets a custom standard.
ENET100 sets the standard to ENET100.
FW1394BS400B sets the standard to FW1394BS400B.
FW1394BS800B sets the standard to FW1394BS800B.
FW1394BS1600B sets the standard to FW1394BS1600B.
FBD1 sets the standard to FBD1.
FBD2 sets the standard to FBD2.
FBD3 sets the standard to FBD3.
FC133 sets the standard to FC133.
FC266 sets the standard to FC266.
FC531 sets the standard to FC531.
FC1063 sets the standard to FC1063.
FC2125 sets the standard to FC2125.
FC4250 sets the standard to FC4250.
FC8500 sets the standard to FC8500.
ENET1000 sets the standard to ENET1000.
IBA2500 sets the standard to IBA2500.
IBA_GEN2 sets the standard to IBA_GEN2.
OC1 sets the standard to OC1.
OC3 sets the standard to OC3.
OC12 sets the standard to OC12.
OC48 sets the standard to OC48.
PCIE _GEN1 sets the standard to PCIE_GEN1.
PCIE_GEN2 sets the standard to PCIE_GEN2.
PCIE_GEN3 sets the standard to PCIE_GEN3.
RIO125 sets the standard to RIO125.
RIO250 sets the standard to RIO250.
RIO3125 sets the standard to RIO3125.
SAS15_NOSSC sets the standard to SAS15_NOSSC.
SAS3_NOSSC sets the standard to SAS3_NOSSC.
SAS6_NOSSC sets the standard to SAS6_NOSSC.
SAS12_NOSSC sets the standard to SAS12_NOSSC.
SAS15_SSC sets the standard to SAS15_SSC.
SAS3_SSC sets the standard to SAS3_SSC.
SAS6_SSC sets the standard to SAS6_SSC.
SAS12_SSC sets the standard to SAS12_SSC.
SATA_GEN1 sets the standard to SATA_GEN1.
SATA_GEN2 sets the standard to SATA_GEN2.
SATA_GEN3 sets the standard to SATA_GEN3.
USB3 sets the standard to USB3.
XAUI sets the standard to XAUI.
XAUI_GEN2 sets the standard to XAUI_GEN2.

tdcompensation `property` ¶

tdcompensation: MeasurementClockrecoveryTdcompensation

Return the MEASUrement:CLOCKRecovery:TDCOMPensation command.

Description

This command sets the PLL clock recovery loop feedback time-constants such that the actual transfer function matches closely to a mathematical filter polynomial. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:TDCOMPensation? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:TDCOMPensation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:TDCOMPensation value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:TDCOMPensation {1|0}
- MEASUrement:CLOCKRecovery:TDCOMPensation?

Info

1 specifies automatic transition density compensation is on.
0 specifies automatic transition density compensation is off.

MeasurementClockrecoveryAdvanced ¶

Bases: SCPICmdRead

The MEASUrement:CLOCKRecovery:ADVanced command tree.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:ADVanced? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:ADVanced? query and raise an AssertionError if the returned value does not match value.

Properties

.method: The MEASUrement:CLOCKRecovery:ADVanced:METHod command.

method `property` ¶

method: MeasurementClockrecoveryAdvancedMethod

Return the MEASUrement:CLOCKRecovery:ADVanced:METHod command.

Description

This command sets or queries the global advanced clock recovery method. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:ADVanced:METHod? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:ADVanced:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:ADVanced:METHod value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:CLOCKRecovery:ADVanced:METHod?

Info

NONE sets to use no advanced CRD method.
NOMinal sets the advanced CRD method to Nominal Data Rate.
PATTern sets the advanced CDR method to use a Known Data Pattern.

MeasurementClockrecoveryAdvancedMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:ADVanced:METHod command.

Description

This command sets or queries the global advanced clock recovery method. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:ADVanced:METHod? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:ADVanced:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:ADVanced:METHod value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:CLOCKRecovery:ADVanced:METHod?

Info

NONE sets to use no advanced CRD method.
NOMinal sets the advanced CRD method to Nominal Data Rate.
PATTern sets the advanced CDR method to use a Known Data Pattern.

MeasurementClockrecoveryClockfrequency ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:CLOCKFrequency command.

Description

This command sets or queries the global clock frequency used when fixed constant clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:CLOCKFrequency? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:CLOCKFrequency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:CLOCKFrequency value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:CLOCKRecovery:CLOCKFrequency?

Info

<NR3> is the global clock frequency used with Constant Clock - Fixed clock recovery method.

MeasurementClockrecoveryClockmultiplier ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:CLOCKMultiplier command.

Description

This command sets or queries the global clock multiplier used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:CLOCKMultiplier? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:CLOCKMultiplier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:CLOCKMultiplier value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:CLOCKRecovery:CLOCKMultiplier?

Info

<NR3> is the global clock multiplier.

MeasurementClockrecoveryConstclockmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:CONSTCLOCKMODe command.

Description

This command sets or queries the global constant clock mode used when constant clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:CONSTCLOCKMODe value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}
- MEASUrement:CLOCKRecovery:CONSTCLOCKMODe?

Info

MEAN sets the constant clock mode to MEAN.
MEDian sets the constant clock mode to MEDian.
FIXed sets the constant clock mode to FIXed.

MeasurementClockrecoveryDamping ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:DAMPing command.

Description

This command sets or queries the global damping value used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:DAMPing? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:DAMPing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:DAMPing value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:CLOCKRecovery:DAMPing?

Info

<NR3> is the global clock recovery damping value.

MeasurementClockrecoveryDatapath ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:DATAPath command.

Description

This command sets or queries the global file containing the data pattern used when known data pattern clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:DATAPath? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:DATAPath? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:DATAPath value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:DATAPath <QString>
- MEASUrement:CLOCKRecovery:DATAPath?

Info

<QString> is the path and filename, in quotes, of the file containing the data pattern.

MeasurementClockrecoveryDatarate ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:DATARate command.

Description

This command sets or queries the global nominal data bit rate used when nominal data rate clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:DATARate? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:DATARate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:DATARate value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:DATARate <NR3>
- MEASUrement:CLOCKRecovery:DATARate?

Info

<NR3> is the global value for the Nominal data rate.

MeasurementClockrecoveryExplicitclockmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe command.

Description

This command sets or queries the global explicit clock mode used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:CLOCKRecovery:EXPLICITCLOCKMODe?

Info

EDGE sets the clock mode to clock edge.
PLL sets the clock mode to phase locked loop.

MeasurementClockrecoveryJtfbandwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:JTFBandwidth command.

Description

This command sets or queries the global JTF bandwidth used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:JTFBandwidth? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:JTFBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:JTFBandwidth value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:CLOCKRecovery:JTFBandwidth?

Info

<NR3> is the global clock recovery JTF bandwidth.

MeasurementClockrecoveryLoopbandwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:LOOPBandwidth command.

Description

This command sets or queries the global loop bandwidth used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:LOOPBandwidth? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:LOOPBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:LOOPBandwidth value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:CLOCKRecovery:LOOPBandwidth?

Info

<NR3> is the global loop bandwidth.

MeasurementClockrecoveryMeanautocalculate ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:MEANAUTOCalculate command.

Description

This command sets or queries how often the clock is calculated when constant clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:MEANAUTOCalculate? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:MEANAUTOCalculate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:MEANAUTOCalculate value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:CLOCKRecovery:MEANAUTOCalculate?

Info

FIRST calculates the clock on the first acquisition.
EVERY calculates the clock on every acquisition.

MeasurementClockrecoveryMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:METHod command.

Description

This command sets or queries the global clock recovery method for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:METHod? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:METHod value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:CLOCKRecovery:METHod?

Info

PLL specifies using the phase locked loop.
CONSTANTCLOCK specifies using a constant clock.
EXPLICITCLOCK specifies using an explicit clock.

MeasurementClockrecoveryModel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:MODel command.

Description

This command sets or queries the global phase locked loop (PLL) clock recovery model used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:MODel? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:MODel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:MODel value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:MODel TYPE<x>
- MEASUrement:CLOCKRecovery:MODel?

Info

TYPE<x> sets PLL clock recovery to a PLL model type. Valid values are 1 or 2.

MeasurementClockrecoveryNominaloffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:NOMINALOFFset command.

Description

This command sets or queries the global offset value used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:CLOCKRecovery:NOMINALOFFset?

Info

<NR3> is the global clock offset.

Properties

.selectiontype: The MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

selectiontype `property` ¶

selectiontype: MeasurementClockrecoveryNominaloffsetSelectiontype

Return the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

Description

This command sets or queries the global offset type used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?

Info

AUTO sets the selection type to AUTO.
MANUAL sets the selection type to MANUAL.

MeasurementClockrecoveryNominaloffsetSelectiontype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

Description

This command sets or queries the global offset type used when explicit clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?

Info

AUTO sets the selection type to AUTO.
MANUAL sets the selection type to MANUAL.

MeasurementClockrecoveryStandard ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:STAndard command.

Description

This command sets or queries the global communications standard used when PLL clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:STAndard? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:STAndard? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:STAndard value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}
- MEASUrement:CLOCKRecovery:STAndard?

Info

CUSTom sets a custom standard.
ENET100 sets the standard to ENET100.
FW1394BS400B sets the standard to FW1394BS400B.
FW1394BS800B sets the standard to FW1394BS800B.
FW1394BS1600B sets the standard to FW1394BS1600B.
FBD1 sets the standard to FBD1.
FBD2 sets the standard to FBD2.
FBD3 sets the standard to FBD3.
FC133 sets the standard to FC133.
FC266 sets the standard to FC266.
FC531 sets the standard to FC531.
FC1063 sets the standard to FC1063.
FC2125 sets the standard to FC2125.
FC4250 sets the standard to FC4250.
FC8500 sets the standard to FC8500.
ENET1000 sets the standard to ENET1000.
IBA2500 sets the standard to IBA2500.
IBA_GEN2 sets the standard to IBA_GEN2.
OC1 sets the standard to OC1.
OC3 sets the standard to OC3.
OC12 sets the standard to OC12.
OC48 sets the standard to OC48.
PCIE _GEN1 sets the standard to PCIE_GEN1.
PCIE_GEN2 sets the standard to PCIE_GEN2.
PCIE_GEN3 sets the standard to PCIE_GEN3.
RIO125 sets the standard to RIO125.
RIO250 sets the standard to RIO250.
RIO3125 sets the standard to RIO3125.
SAS15_NOSSC sets the standard to SAS15_NOSSC.
SAS3_NOSSC sets the standard to SAS3_NOSSC.
SAS6_NOSSC sets the standard to SAS6_NOSSC.
SAS12_NOSSC sets the standard to SAS12_NOSSC.
SAS15_SSC sets the standard to SAS15_SSC.
SAS3_SSC sets the standard to SAS3_SSC.
SAS6_SSC sets the standard to SAS6_SSC.
SAS12_SSC sets the standard to SAS12_SSC.
SATA_GEN1 sets the standard to SATA_GEN1.
SATA_GEN2 sets the standard to SATA_GEN2.
SATA_GEN3 sets the standard to SATA_GEN3.
USB3 sets the standard to USB3.
XAUI sets the standard to XAUI.
XAUI_GEN2 sets the standard to XAUI_GEN2.

MeasurementClockrecoveryTdcompensation ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:CLOCKRecovery:TDCOMPensation command.

Description

This command sets the PLL clock recovery loop feedback time-constants such that the actual transfer function matches closely to a mathematical filter polynomial. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:CLOCKRecovery:TDCOMPensation? query.
Using the .verify(value) method will send the MEASUrement:CLOCKRecovery:TDCOMPensation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:CLOCKRecovery:TDCOMPensation value command.

SCPI Syntax

- MEASUrement:CLOCKRecovery:TDCOMPensation {1|0}
- MEASUrement:CLOCKRecovery:TDCOMPensation?

Info

1 specifies automatic transition density compensation is on.
0 specifies automatic transition density compensation is off.

MeasurementDdjmethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:DDJMethod command.

Description

This command sets or queries the model used to separate-out DDJ from TIE.

Usage

Using the .query() method will send the MEASUrement:DDJMethod? query.
Using the .verify(value) method will send the MEASUrement:DDJMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:DDJMethod value command.

SCPI Syntax

- MEASUrement:DDJMethod {SPECtraldomain|TIMDomain}
- MEASUrement:DDJMethod?

MeasurementDelete ¶

Bases: SCPICmdWrite

The MEASUrement:DELete command.

Description

The command deletes the specified measurement.

Usage

Using the .write(value) method will send the MEASUrement:DELete value command.

SCPI Syntax

- MEASUrement:DELete <QString>

Info

<QString> is the measurement to delete. Argument is of the form ‘MEAS’ where is ≥1.

MeasurementDeleteall ¶

Bases: SCPICmdWriteNoArguments

The MEASUrement:DELETEALL command.

Description

This command deletes all the active instances of measurements defined in the scope application.

Usage

Using the .write() method will send the MEASUrement:DELETEALL command.

SCPI Syntax

- MEASUrement:DELETEALL

MeasurementDiracmodel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:DIRacmodel command.

Description

This command sets or queries the dirac model used to separate random from deterministic jitter for jitter measurements.

Usage

Using the .query() method will send the MEASUrement:DIRacmodel? query.
Using the .verify(value) method will send the MEASUrement:DIRacmodel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:DIRacmodel value command.

SCPI Syntax

- MEASUrement:DIRacmodel {PCIExpress|FIBREchannel}
- MEASUrement:DIRacmodel?

Info

PCIExpress specifies the PCIExpress dirac model.
FIBREchannel specifies the FIBREchannel dirac model.

MeasurementDisplayunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:DISPLAYUnits command.

Description

This command sets or queries the display units used for jitter summary measurements.

Usage

Using the .query() method will send the MEASUrement:DISPLAYUnits? query.
Using the .verify(value) method will send the MEASUrement:DISPLAYUnits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:DISPLAYUnits value command.

SCPI Syntax

- MEASUrement:DISPLAYUnits {SEConds|UNITINtervals}
- MEASUrement:DISPLAYUnits?

Info

SEConds set the display units to seconds.
UNITINtervals set the display units to unit intervals.

MeasurementEdgeItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:EDGE<x> command.

Description

This command sets or queries the type of the edge for the measurement.

Usage

Using the .query() method will send the MEASUrement:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:EDGE<x> value command.

SCPI Syntax

- MEASUrement:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:EDGE<x>?

Info

FALL specifies the falling edge of the waveform.
RISE specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.

MeasurementEnablepjitter ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:ENABLEPjitter command.

Description

This command sets or queries the state of period jitter analysis mode.

Usage

Using the .query() method will send the MEASUrement:ENABLEPjitter? query.
Using the .verify(value) method will send the MEASUrement:ENABLEPjitter? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:ENABLEPjitter value command.

SCPI Syntax

- MEASUrement:ENABLEPjitter {ON|OFF|1|0}
- MEASUrement:ENABLEPjitter?

Info

ON indicates that period jitter analysis mode is active.
OFF indicates that period jitter analysis mode is off.
1 turns on period jitter analysis mode. Any number value other than 0 will turn period jitter analysis mode on.
0 turns off period jitter analysis mode.

MeasurementEyerender ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:EYERENDER command.

Description

This command sets or queries the state of high-performance eye rendering for an eye diagram.

Usage

Using the .query() method will send the MEASUrement:EYERENDER? query.
Using the .verify(value) method will send the MEASUrement:EYERENDER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:EYERENDER value command.

SCPI Syntax

- MEASUrement:EYERENDER {ON|OFF|<NR1>}
- MEASUrement:EYERENDER?

Info

<NR1> = 0 disables high-performance eye rendering for an eye diagram; any other value turns this feature on.
OFF disables high-performance eye rendering for an eye diagram.
ON enables high-performance eye rendering for an eye diagram.

MeasurementFilters ¶

Bases: SCPICmdRead

The MEASUrement:FILTers command tree.

Usage

Using the .query() method will send the MEASUrement:FILTers? query.
Using the .verify(value) method will send the MEASUrement:FILTers? query and raise an AssertionError if the returned value does not match value.

Properties

.blankingtime: The MEASUrement:FILTers:BLANKingtime command.
.highpass: The MEASUrement:FILTers:HIGHPass command tree.
.lowpass: The MEASUrement:FILTers:LOWPass command tree.
.ramptime: The MEASUrement:FILTers:RAMPtime command.

blankingtime `property` ¶

blankingtime: MeasurementFiltersBlankingtime

Return the MEASUrement:FILTers:BLANKingtime command.

Description

This command sets or queries the global filter blanking time.

Usage

Using the .query() method will send the MEASUrement:FILTers:BLANKingtime? query.
Using the .verify(value) method will send the MEASUrement:FILTers:BLANKingtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:BLANKingtime value command.

SCPI Syntax

- MEASUrement:FILTers:BLANKingtime <NR3>
- MEASUrement:FILTers:BLANKingtime?

Info

<NR3> is the current filter blanking time.

highpass `property` ¶

highpass: MeasurementFiltersHighpass

Return the MEASUrement:FILTers:HIGHPass command tree.

Usage

Using the .query() method will send the MEASUrement:FILTers:HIGHPass? query.
Using the .verify(value) method will send the MEASUrement:FILTers:HIGHPass? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.freq: The MEASUrement:FILTers:HIGHPass:FREQ command.
.spec: The MEASUrement:FILTers:HIGHPass:SPEC command.

lowpass `property` ¶

lowpass: MeasurementFiltersLowpass

Return the MEASUrement:FILTers:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:FILTers:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:FILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.freq: The MEASUrement:FILTers:LOWPass:FREQ command.
.spec: The MEASUrement:FILTers:LOWPass:SPEC command.

ramptime `property` ¶

ramptime: MeasurementFiltersRamptime

Return the MEASUrement:FILTers:RAMPtime command.

Description

This command sets or queries the global filter ramp time for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:RAMPtime? query.
Using the .verify(value) method will send the MEASUrement:FILTers:RAMPtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:RAMPtime value command.

SCPI Syntax

- MEASUrement:FILTers:RAMPtime <NR3>
- MEASUrement:FILTers:RAMPtime?

Info

<NR3> is the current filter ramp time.

MeasurementFiltersBlankingtime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:FILTers:BLANKingtime command.

Description

This command sets or queries the global filter blanking time.

Usage

Using the .query() method will send the MEASUrement:FILTers:BLANKingtime? query.
Using the .verify(value) method will send the MEASUrement:FILTers:BLANKingtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:BLANKingtime value command.

SCPI Syntax

- MEASUrement:FILTers:BLANKingtime <NR3>
- MEASUrement:FILTers:BLANKingtime?

Info

<NR3> is the current filter blanking time.

MeasurementFiltersHighpass ¶

Bases: SCPICmdRead

The MEASUrement:FILTers:HIGHPass command tree.

Usage

Using the .query() method will send the MEASUrement:FILTers:HIGHPass? query.
Using the .verify(value) method will send the MEASUrement:FILTers:HIGHPass? query and raise an AssertionError if the returned value does not match value.

Properties

.freq: The MEASUrement:FILTers:HIGHPass:FREQ command.
.spec: The MEASUrement:FILTers:HIGHPass:SPEC command.

freq `property` ¶

freq: MeasurementFiltersHighpassFreq

Return the MEASUrement:FILTers:HIGHPass:FREQ command.

Description

This command sets or queries the global high pass filter frequency for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:HIGHPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:FILTers:HIGHPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:HIGHPass:FREQ value command.

SCPI Syntax

- MEASUrement:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:FILTers:HIGHPass:FREQ?

Info

<NR3> is the current high pass filter frequency.

spec `property` ¶

spec: MeasurementFiltersHighpassSpec

Return the MEASUrement:FILTers:HIGHPass:SPEC command.

Description

This command sets or queries the global high pass filter order for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:HIGHPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:FILTers:HIGHPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:HIGHPass:SPEC value command.

SCPI Syntax

- MEASUrement:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:HIGHPass:SPEC?

Info

NONE specifies no high pass filter.
FIRST specifies a first order high pass filter.
SECOND specifies a second order high pass filter.
THIRD specifies a third order high pass filter.

MeasurementFiltersHighpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:FILTers:HIGHPass:FREQ command.

Description

This command sets or queries the global high pass filter frequency for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:HIGHPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:FILTers:HIGHPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:HIGHPass:FREQ value command.

SCPI Syntax

- MEASUrement:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:FILTers:HIGHPass:FREQ?

Info

<NR3> is the current high pass filter frequency.

MeasurementFiltersHighpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:FILTers:HIGHPass:SPEC command.

Description

This command sets or queries the global high pass filter order for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:HIGHPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:FILTers:HIGHPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:HIGHPass:SPEC value command.

SCPI Syntax

- MEASUrement:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:HIGHPass:SPEC?

Info

NONE specifies no high pass filter.
FIRST specifies a first order high pass filter.
SECOND specifies a second order high pass filter.
THIRD specifies a third order high pass filter.

MeasurementFiltersLowpass ¶

Bases: SCPICmdRead

The MEASUrement:FILTers:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:FILTers:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:FILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.

Properties

.freq: The MEASUrement:FILTers:LOWPass:FREQ command.
.spec: The MEASUrement:FILTers:LOWPass:SPEC command.

freq `property` ¶

freq: MeasurementFiltersLowpassFreq

Return the MEASUrement:FILTers:LOWPass:FREQ command.

Description

This command sets or queries the global low pass filter cutoff frequency for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:FILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:FILTers:LOWPass:FREQ?

Info

<NR3> is the current low pass filter frequency.

spec `property` ¶

spec: MeasurementFiltersLowpassSpec

Return the MEASUrement:FILTers:LOWPass:SPEC command.

Description

This command sets or queries the global low pass filter order for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:FILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:LOWPass:SPEC?

Info

NONE specifies no low pass filter.
FIRST specifies a first order low pass filter.
SECOND specifies a second order low pass filter.
THIRD specifies a third order low pass filter.

MeasurementFiltersLowpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:FILTers:LOWPass:FREQ command.

Description

This command sets or queries the global low pass filter cutoff frequency for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:FILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:FILTers:LOWPass:FREQ?

Info

<NR3> is the current low pass filter frequency.

MeasurementFiltersLowpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:FILTers:LOWPass:SPEC command.

Description

This command sets or queries the global low pass filter order for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:FILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:FILTers:LOWPass:SPEC?

Info

NONE specifies no low pass filter.
FIRST specifies a first order low pass filter.
SECOND specifies a second order low pass filter.
THIRD specifies a third order low pass filter.

MeasurementFiltersRamptime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:FILTers:RAMPtime command.

Description

This command sets or queries the global filter ramp time for the measurement.

Usage

Using the .query() method will send the MEASUrement:FILTers:RAMPtime? query.
Using the .verify(value) method will send the MEASUrement:FILTers:RAMPtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:FILTers:RAMPtime value command.

SCPI Syntax

- MEASUrement:FILTers:RAMPtime <NR3>
- MEASUrement:FILTers:RAMPtime?

Info

<NR3> is the current filter ramp time.

MeasurementGating ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing command.

Description

This command sets or queries the global gating type for the measurement.

Usage

Using the .query() method will send the MEASUrement:GATing? query.
Using the .verify(value) method will send the MEASUrement:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing value command.

SCPI Syntax

- MEASUrement:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:GATing?

Info

NONE turns off measurement gating.
SCREEN turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only on the portion of the waveform where the logic source is in the active state.
SEARCH specifies that measurements are taken based on search criteria.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Properties

.active: The MEASUrement:GATing:ACTive command.
.endtime: The MEASUrement:GATing:ENDtime command.
.hysteresis: The MEASUrement:GATing:HYSTeresis command.
.logicsource: The MEASUrement:GATing:LOGICSource command.
.midref: The MEASUrement:GATing:MIDRef command.
.searchsource: The MEASUrement:GATing:SEARCHSource command.
.starttime: The MEASUrement:GATing:STARTtime command.

active `property` ¶

active: MeasurementGatingActive

Return the MEASUrement:GATing:ACTive command.

Description

This command sets or queries the global gating active level used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?

Info

HIGH specifies the gate is HIGH.
LOW specifies the gate is LOW.

endtime `property` ¶

endtime: MeasurementGatingEndtime

Return the MEASUrement:GATing:ENDtime command.

Description

Sets or queries the end gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?

Info

<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

hysteresis `property` ¶

hysteresis: MeasurementGatingHysteresis

Return the MEASUrement:GATing:HYSTeresis command.

Description

This command sets or queries the global gating hysteresis value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?

Info

<NR3> is the gating hysteresis.

logicsource `property` ¶

logicsource: MeasurementGatingLogicsource

Return the MEASUrement:GATing:LOGICSource command.

Description

This command sets or queries the gating data source used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:LOGICSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:LOGICSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

midref `property` ¶

midref: MeasurementGatingMidref

Return the MEASUrement:GATing:MIDRef command.

Description

This command sets or queries the global gating mid ref value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?

Info

<NR3> is the mid ref value for gating.

searchsource `property` ¶

searchsource: MeasurementGatingSearchsource

Return the MEASUrement:GATing:SEARCHSource command.

Description

This command sets or queries the global gating search source when the gating type is search.

Usage

Using the .query() method will send the MEASUrement:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:GATing:SEARCHSource SEARCH<x>
- MEASUrement:GATing:SEARCHSource?

Info

SEARCH<x> specifies the search source.

starttime `property` ¶

starttime: MeasurementGatingStarttime

Return the MEASUrement:GATing:STARTtime command.

Description

Sets or queries the start gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?

Info

<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementGatingActive ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:ACTive command.

Description

This command sets or queries the global gating active level used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:GATing:ACTive {HIGH|LOW}
- MEASUrement:GATing:ACTive?

Info

HIGH specifies the gate is HIGH.
LOW specifies the gate is LOW.

MeasurementGatingEndtime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:ENDtime command.

Description

Sets or queries the end gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:GATing:ENDtime <NR3>
- MEASUrement:GATing:ENDtime?

Info

<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementGatingHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:HYSTeresis command.

Description

This command sets or queries the global gating hysteresis value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:GATing:HYSTeresis <NR3>
- MEASUrement:GATing:HYSTeresis?

Info

<NR3> is the gating hysteresis.

MeasurementGatingLogicsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:LOGICSource command.

Description

This command sets or queries the gating data source used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:LOGICSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:LOGICSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}
- MEASUrement:GATing:LOGICSource?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementGatingMidref ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:MIDRef command.

Description

This command sets or queries the global gating mid ref value used for logic gating.

Usage

Using the .query() method will send the MEASUrement:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:GATing:MIDRef <NR3>
- MEASUrement:GATing:MIDRef?

Info

<NR3> is the mid ref value for gating.

MeasurementGatingSearchsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:SEARCHSource command.

Description

This command sets or queries the global gating search source when the gating type is search.

Usage

Using the .query() method will send the MEASUrement:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:GATing:SEARCHSource SEARCH<x>
- MEASUrement:GATing:SEARCHSource?

Info

SEARCH<x> specifies the search source.

MeasurementGatingStarttime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:GATing:STARTtime command.

Description

Sets or queries the start gate time for all measurements that use Global gating.

Usage

Using the .query() method will send the MEASUrement:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:GATing:STARTtime <NR3>
- MEASUrement:GATing:STARTtime?

Info

<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementHighlevel ¶

Bases: SCPICmdRead

The MEASUrement:HIGHLEVel command tree.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel? query and raise an AssertionError if the returned value does not match value.

Properties

.configuration: The MEASUrement:HIGHLEVel:CONFIGuration command.
.edgequalifier: The MEASUrement:HIGHLEVel:EDGEQUALifier command.
.inlowpass: The MEASUrement:HIGHLEVel:INLOWPass command tree.
.l2ltol2n: The MEASUrement:HIGHLEVel:L2LTOL2N command.
.lineselected: The MEASUrement:HIGHLEVel:LINESelected command.
.outedgequalifier: The MEASUrement:HIGHLEVel:OUTEDGEQUALifier command.
.outl2ltol2n: The MEASUrement:HIGHLEVel:OUTL2LTOL2N command.
.outlineselected: The MEASUrement:HIGHLEVel:OUTLINESelected command.
.outlowpass: The MEASUrement:HIGHLEVel:OUTLOWPass command tree.
.outsource: The MEASUrement:HIGHLEVel:OUTSOURCE command.
.outwiring: The MEASUrement:HIGHLEVel:OUTWIRing command.
.source: The MEASUrement:HIGHLEVel:SOURCE command.
.wiring: The MEASUrement:HIGHLEVel:WIRing command.

configuration `property` ¶

configuration: MeasurementHighlevelConfiguration

Return the MEASUrement:HIGHLEVel:CONFIGuration command.

Description

This command sets or queries the global input and output configuration.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:CONFIGuration? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:CONFIGuration? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:CONFIGuration value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:HIGHLEVel:CONFIGuration?

Info

INPUT specifies the source settings configuration as input.
OUTPUT specifies the source settings configuration as output.

edgequalifier `property` ¶

edgequalifier: MeasurementHighlevelEdgequalifier

Return the MEASUrement:HIGHLEVel:EDGEQUALifier command.

Description

This command sets or queries global input edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:EDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:EDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:EDGEQUALifier value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:EDGEQUALifier?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

inlowpass `property` ¶

inlowpass: MeasurementHighlevelInlowpass

Return the MEASUrement:HIGHLEVel:INLOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:INLOWPass? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:INLOWPass? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.freq: The MEASUrement:HIGHLEVel:INLOWPass:FREQ command.
.spec: The MEASUrement:HIGHLEVel:INLOWPass:SPEC command.

l2ltol2n `property` ¶

l2ltol2n: MeasurementHighlevelL2ltol2n

Return the MEASUrement:HIGHLEVel:L2LTOL2N command.

Description

This command enables the Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:L2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:L2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:L2LTOL2N value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:L2LTOL2N?

lineselected `property` ¶

lineselected: MeasurementHighlevelLineselected

Return the MEASUrement:HIGHLEVel:LINESelected command.

Description

This command sets or queries global input select lines.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:LINESelected? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:LINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:LINESelected value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:HIGHLEVel:LINESelected?

Info

ABCB specifies the global input select lines as ABCB.
ACBC specifies the global input select lines as ACBC.
BACA specifies the global input select lines as BACA.
AN specifies the global input select lines as AN.
BN specifies the global input select lines as BN.
CN specifies the global input select lines as CN.

outedgequalifier `property` ¶

outedgequalifier: MeasurementHighlevelOutedgequalifier

Return the MEASUrement:HIGHLEVel:OUTEDGEQUALifier command.

Description

This command sets or queries global output edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTEDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTEDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTEDGEQUALifier value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTEDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

outl2ltol2n `property` ¶

outl2ltol2n: MeasurementHighlevelOutl2ltol2n

Return the MEASUrement:HIGHLEVel:OUTL2LTOL2N command.

Description

This command sets or queries global output Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTL2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTL2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTL2LTOL2N value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:OUTL2LTOL2N?

outlineselected `property` ¶

outlineselected: MeasurementHighlevelOutlineselected

Return the MEASUrement:HIGHLEVel:OUTLINESelected command.

Description

This command sets or queries global output select lines.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLINESelected? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTLINESelected value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:HIGHLEVel:OUTLINESelected?

Info

XYZY specifies the global output select lines as XYZY.
XZYZ specifies the global output select lines as XZYZ.
YXZX specifies the global output select lines as YXZX.
XN specifies the global output select lines as XN.
YN specifies the global output select lines as YN.
ZN specifies the global output select lines as ZN.

outlowpass `property` ¶

outlowpass: MeasurementHighlevelOutlowpass

Return the MEASUrement:HIGHLEVel:OUTLOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLOWPass? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.freq: The MEASUrement:HIGHLEVel:OUTLOWPass:FREQ command.
.spec: The MEASUrement:HIGHLEVel:OUTLOWPass:SPEC command.

outsource `property` ¶

outsource: MeasurementHighlevelOutsource

Return the MEASUrement:HIGHLEVel:OUTSOURCE command.

Description

This command sets or queries global output source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTSOURCE? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTSOURCE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTSOURCE value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTSOURCE {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTSOURCE?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

outwiring `property` ¶

outwiring: MeasurementHighlevelOutwiring

Return the MEASUrement:HIGHLEVel:OUTWIRing command.

Description

This command sets or queries the global output wiring.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTWIRing? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTWIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTWIRing value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTWIRing {P1W2V1I1|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:OUTWIRing?

Info

P1W2V1I1 specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.
P3W3V2I2 specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.
P3W3V3I3 specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.
P3W3 specifies 3 phase and 3 wire, the 3rd wire being Neutral.
DCP1W2 specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.

source `property` ¶

source: MeasurementHighlevelSource

Return the MEASUrement:HIGHLEVel:SOURCE command.

Description

This command sets or queries global input source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:SOURCE? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:SOURCE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:SOURCE value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:SOURCE {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:SOURCE?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

wiring `property` ¶

wiring: MeasurementHighlevelWiring

Return the MEASUrement:HIGHLEVel:WIRing command.

Description

This command sets or queries the wiring configuration for the measurement.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:WIRing? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:WIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:WIRing value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:WIRing?

Info

P1W2V1I1 specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.
P1W3V2I2 specifies 1 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.
P3W3V2I2 specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.
P3W3V3I3 specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.
P3W3 specifies 3 phase and 3 wire, the 3rd wire being Neutral.
DCP1W2 specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.

MeasurementHighlevelConfiguration ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:CONFIGuration command.

Description

This command sets or queries the global input and output configuration.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:CONFIGuration? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:CONFIGuration? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:CONFIGuration value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:HIGHLEVel:CONFIGuration?

Info

INPUT specifies the source settings configuration as input.
OUTPUT specifies the source settings configuration as output.

MeasurementHighlevelEdgequalifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:EDGEQUALifier command.

Description

This command sets or queries global input edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:EDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:EDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:EDGEQUALifier value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:EDGEQUALifier?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementHighlevelInlowpass ¶

Bases: SCPICmdRead

The MEASUrement:HIGHLEVel:INLOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:INLOWPass? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:INLOWPass? query and raise an AssertionError if the returned value does not match value.

Properties

.freq: The MEASUrement:HIGHLEVel:INLOWPass:FREQ command.
.spec: The MEASUrement:HIGHLEVel:INLOWPass:SPEC command.

freq `property` ¶

freq: MeasurementHighlevelInlowpassFreq

Return the MEASUrement:HIGHLEVel:INLOWPass:FREQ command.

Description

This command sets or queries global input low pass filter frequency.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:INLOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:INLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:INLOWPass:FREQ?

Info

<NR3> specifies the global input low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.

spec `property` ¶

spec: MeasurementHighlevelInlowpassSpec

Return the MEASUrement:HIGHLEVel:INLOWPass:SPEC command.

Description

This command sets or queries global input low pass filter order.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:INLOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:INLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:INLOWPass:SPEC?

Info

NONE specifies the global input low pass filter order as none.
FIRST specifies the global input low pass filter order as first.
SECOND specifies the global input low pass filter order as second.
THIRD specifies the global input low pass filter order as third.

MeasurementHighlevelInlowpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:INLOWPass:FREQ command.

Description

This command sets or queries global input low pass filter frequency.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:INLOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:INLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:INLOWPass:FREQ?

Info

<NR3> specifies the global input low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.

MeasurementHighlevelInlowpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:INLOWPass:SPEC command.

Description

This command sets or queries global input low pass filter order.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:INLOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:INLOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:INLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:INLOWPass:SPEC?

Info

NONE specifies the global input low pass filter order as none.
FIRST specifies the global input low pass filter order as first.
SECOND specifies the global input low pass filter order as second.
THIRD specifies the global input low pass filter order as third.

MeasurementHighlevelL2ltol2n ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:L2LTOL2N command.

Description

This command enables the Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:L2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:L2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:L2LTOL2N value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:L2LTOL2N?

MeasurementHighlevelLineselected ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:LINESelected command.

Description

This command sets or queries global input select lines.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:LINESelected? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:LINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:LINESelected value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:HIGHLEVel:LINESelected?

Info

ABCB specifies the global input select lines as ABCB.
ACBC specifies the global input select lines as ACBC.
BACA specifies the global input select lines as BACA.
AN specifies the global input select lines as AN.
BN specifies the global input select lines as BN.
CN specifies the global input select lines as CN.

MeasurementHighlevelOutedgequalifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:OUTEDGEQUALifier command.

Description

This command sets or queries global output edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTEDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTEDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTEDGEQUALifier value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTEDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTEDGEQUALifier?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementHighlevelOutl2ltol2n ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:OUTL2LTOL2N command.

Description

This command sets or queries global output Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTL2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTL2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTL2LTOL2N value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:HIGHLEVel:OUTL2LTOL2N?

MeasurementHighlevelOutlineselected ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:OUTLINESelected command.

Description

This command sets or queries global output select lines.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLINESelected? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTLINESelected value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:HIGHLEVel:OUTLINESelected?

Info

XYZY specifies the global output select lines as XYZY.
XZYZ specifies the global output select lines as XZYZ.
YXZX specifies the global output select lines as YXZX.
XN specifies the global output select lines as XN.
YN specifies the global output select lines as YN.
ZN specifies the global output select lines as ZN.

MeasurementHighlevelOutlowpass ¶

Bases: SCPICmdRead

The MEASUrement:HIGHLEVel:OUTLOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLOWPass? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass? query and raise an AssertionError if the returned value does not match value.

Properties

.freq: The MEASUrement:HIGHLEVel:OUTLOWPass:FREQ command.
.spec: The MEASUrement:HIGHLEVel:OUTLOWPass:SPEC command.

freq `property` ¶

freq: MeasurementHighlevelOutlowpassFreq

Return the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ command.

Description

This command sets or queries global output low pass filter frequency.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ?

Info

<NR3> specifies the global output low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.

spec `property` ¶

spec: MeasurementHighlevelOutlowpassSpec

Return the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC command.

Description

This command sets or queries global output low pass filter order.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC?

Info

NONE specifies the global output low pass filter order as none.
FIRST specifies the global output low pass filter order as first.
SECOND specifies the global output low pass filter order as second.
THIRD specifies the global output low pass filter order as third.

MeasurementHighlevelOutlowpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:OUTLOWPass:FREQ command.

Description

This command sets or queries global output low pass filter frequency.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ <NR3>
- MEASUrement:HIGHLEVel:OUTLOWPass:FREQ?

Info

<NR3> specifies the global output low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.

MeasurementHighlevelOutlowpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:OUTLOWPass:SPEC command.

Description

This command sets or queries global output low pass filter order.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTLOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:HIGHLEVel:OUTLOWPass:SPEC?

Info

NONE specifies the global output low pass filter order as none.
FIRST specifies the global output low pass filter order as first.
SECOND specifies the global output low pass filter order as second.
THIRD specifies the global output low pass filter order as third.

MeasurementHighlevelOutsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:OUTSOURCE command.

Description

This command sets or queries global output source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTSOURCE? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTSOURCE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTSOURCE value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTSOURCE {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:OUTSOURCE?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementHighlevelOutwiring ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:OUTWIRing command.

Description

This command sets or queries the global output wiring.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:OUTWIRing? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:OUTWIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:OUTWIRing value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:OUTWIRing {P1W2V1I1|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:OUTWIRing?

Info

P1W2V1I1 specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.
P3W3V2I2 specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.
P3W3V3I3 specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.
P3W3 specifies 3 phase and 3 wire, the 3rd wire being Neutral.
DCP1W2 specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.

MeasurementHighlevelSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:SOURCE command.

Description

This command sets or queries global input source.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:SOURCE? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:SOURCE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:SOURCE value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:SOURCE {CH<x>|MATH<x>|REF<x>}
- MEASUrement:HIGHLEVel:SOURCE?

Info

CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementHighlevelWiring ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:HIGHLEVel:WIRing command.

Description

This command sets or queries the wiring configuration for the measurement.

Usage

Using the .query() method will send the MEASUrement:HIGHLEVel:WIRing? query.
Using the .verify(value) method will send the MEASUrement:HIGHLEVel:WIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:HIGHLEVel:WIRing value command.

SCPI Syntax

- MEASUrement:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:HIGHLEVel:WIRing?

Info

P1W2V1I1 specifies 1 phase- 2 wire (with 1 voltage and 1 current sources) wiring configuration.
P1W3V2I2 specifies 1 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.
P3W3V2I2 specifies 3 phase- 3 wire (with 2 voltage and 2 current sources) wiring configuration.
P3W3V3I3 specifies 3 phase- 3 wire (with 3 voltage and 3 current sources) wiring configuration.
P3W3 specifies 3 phase and 3 wire, the 3rd wire being Neutral.
DCP1W2 specifies DC 1 phase and 2 wire, the 2nd wire being Neutral.

MeasurementInterp ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:INTERp command.

Description

This command sets or queries the interpolation mode used to locate edge crossings.

Usage

Using the .query() method will send the MEASUrement:INTERp? query.
Using the .verify(value) method will send the MEASUrement:INTERp? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:INTERp value command.

SCPI Syntax

- MEASUrement:INTERp {AUTO|SINX|LINear}
- MEASUrement:INTERp?

Info

AUTO automatically selects the interpolation mode.
SINX specifies sin(x)/x interpolation, where acquired points are fit to a curve.
LINear specifies linear interpolation, where acquired points are connected with straight lines.

MeasurementJittermodel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:JITTermodel command.

Description

This command sets or queries the model used to separate random from deterministic jitter for jitter measurements.

Usage

Using the .query() method will send the MEASUrement:JITTermodel? query.
Using the .verify(value) method will send the MEASUrement:JITTermodel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:JITTermodel value command.

SCPI Syntax

- MEASUrement:JITTermodel {SPECTRAL|SPECTRALBUJ}
- MEASUrement:JITTermodel?

Info

SPECTRAL sets the jitter separation model to spectral only.
SPECTRALBUJ sets the jitter separation model to spectral plus BUJ.

MeasurementList ¶

Bases: SCPICmdRead

The MEASUrement:LIST command.

Description

This query returns a comma separated list of all currently defined measurements.

Usage

Using the .query() method will send the MEASUrement:LIST? query.
Using the .verify(value) method will send the MEASUrement:LIST? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:LIST?

MeasurementLockrj ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:LOCKRJ command.

Description

This command sets or queries the state of RJ locking.

Usage

Using the .query() method will send the MEASUrement:LOCKRJ? query.
Using the .verify(value) method will send the MEASUrement:LOCKRJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:LOCKRJ value command.

SCPI Syntax

- MEASUrement:LOCKRJ {ON|OFF|1|0}
- MEASUrement:LOCKRJ?

Info

ON indicates that RJ locking is active.
OFF indicates that RJ locking is off.
1 turns on RJ locking. Any number value other than 0 will turn RJ locking on.
0 turns off RJ locking.

MeasurementLockrjvalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:LOCKRJValue command.

Description

This command sets or queries the RJ lock value.

Usage

Using the .query() method will send the MEASUrement:LOCKRJValue? query.
Using the .verify(value) method will send the MEASUrement:LOCKRJValue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:LOCKRJValue value command.

SCPI Syntax

- MEASUrement:LOCKRJValue <NR3>
- MEASUrement:LOCKRJValue?

Info

<NR3> default value = 1e-12; minimum value = 1e-15; maximum value = 1.

MeasurementMathItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The MEASUrement:MATH<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.reflevels: The MEASUrement:MATH<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementMathItemReflevels

Return the MEASUrement:MATH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.absolute: The MEASUrement:MATH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:MATH<x>:REFLevels:BASETop command.
.method: The MEASUrement:MATH<x>:REFLevels:METHod command.
.percent: The MEASUrement:MATH<x>:REFLevels:PERCent command tree.

MeasurementMathItemReflevels ¶

Bases: SCPICmdRead

The MEASUrement:MATH<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.absolute: The MEASUrement:MATH<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:MATH<x>:REFLevels:BASETop command.
.method: The MEASUrement:MATH<x>:REFLevels:METHod command.
.percent: The MEASUrement:MATH<x>:REFLevels:PERCent command tree.

absolute `property` ¶

absolute: MeasurementMathItemReflevelsAbsolute

Return the MEASUrement:MATH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementMathItemReflevelsBasetop

Return the MEASUrement:MATH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?

Info

MATH<x> specifies the math number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

method `property` ¶

method: MeasurementMathItemReflevelsMethod

Return the MEASUrement:MATH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?

Info

MATH<x> specifies the math number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MATH<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MATH<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

percent `property` ¶

percent: MeasurementMathItemReflevelsPercent

Return the MEASUrement:MATH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Sub-properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

MeasurementMathItemReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementMathItemReflevelsAbsoluteFallhigh

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

falllow `property` ¶

falllow: MeasurementMathItemReflevelsAbsoluteFalllow

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measuement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

fallmid `property` ¶

fallmid: MeasurementMathItemReflevelsAbsoluteFallmid

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

hysteresis `property` ¶

hysteresis: MeasurementMathItemReflevelsAbsoluteHysteresis

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementMathItemReflevelsAbsoluteRisehigh

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

riselow `property` ¶

riselow: MeasurementMathItemReflevelsAbsoluteRiselow

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

risemid `property` ¶

risemid: MeasurementMathItemReflevelsAbsoluteRisemid

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Absolute.

type `property` ¶

type: MeasurementMathItemReflevelsAbsoluteType

Return the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?

Info

MATH<x> specifies the math number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMathItemReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measuement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

MeasurementMathItemReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

MeasurementMathItemReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the high reference level, and is the zero percent level when MEASUrement:IMMed:REFLevel:METHod is set to Absolute.

MeasurementMathItemReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement ref level method is set to absolute. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:ABSolute:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Absolute.

MeasurementMathItemReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MATH<x>:REFLevels:ABSolute:TYPE?

Info

MATH<x> specifies the math number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMathItemReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MATH<x>:REFLevels:BASETop?

Info

MATH<x> specifies the math number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

MeasurementMathItemReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:MATH<x>:REFLevels:METHod?

Info

MATH<x> specifies the math number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MATH<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MATH<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementMathItemReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MATH<x> specifies the math number.

Properties

.fallhigh: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementMathItemReflevelsPercentFallhigh

Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level when the measurement Ref level method is set to Percent.

falllow `property` ¶

falllow: MeasurementMathItemReflevelsPercentFalllow

Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

fallmid `property` ¶

fallmid: MeasurementMathItemReflevelsPercentFallmid

Return the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

hysteresis `property` ¶

hysteresis: MeasurementMathItemReflevelsPercentHysteresis

Return the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementMathItemReflevelsPercentRisehigh

Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

riselow `property` ¶

riselow: MeasurementMathItemReflevelsPercentRiselow

Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

risemid `property` ¶

risemid: MeasurementMathItemReflevelsPercentRisemid

Return the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

type `property` ¶

type: MeasurementMathItemReflevelsPercentType

Return the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?

Info

MATH<x> specifies the math number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMathItemReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLLow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:FALLMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 0% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:HYSTeresis?

Info

MATH<x> specifies the math number.
<NR3> is the hysteresis value used for the autoset.

MeasurementMathItemReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEHigh?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISELow?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 100% is equal to TOP) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement ref level method is set to percent. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:MATH<x>:REFLevels:PERCent:RISEMid?

Info

MATH<x> specifies the math number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMathItemReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MATH<x>:REFLevels:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The math number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MATH<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MATH<x>:REFLevels:PERCent:TYPE?

Info

MATH<x> specifies the math number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMeasItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The MEASUrement:MEAS<x> command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.abandwidth: The MEASUrement:MEAS<x>:ABANdwidth command.
.achannels: The MEASUrement:MEAS<x>:ACHANnels command.
.amethod: The MEASUrement:MEAS<x>:AMEThod command.
.bcount: The MEASUrement:MEAS<x>:BCOunt command.
.bdelay: The MEASUrement:MEAS<x>:BDELay command.
.ber: The MEASUrement:MEAS<x>:BER command.
.bin: The MEASUrement:MEAS<x>:BIN command.
.bitabsolute: The MEASUrement:MEAS<x>:BITAbsolute command.
.bitcfgmode: The MEASUrement:MEAS<x>:BITCfgmode command.
.bitend: The MEASUrement:MEAS<x>:BITEnd command.
.bitpcnt: The MEASUrement:MEAS<x>:BITPcnt command.
.bitstart: The MEASUrement:MEAS<x>:BITSTart command.
.bittype: The MEASUrement:MEAS<x>:BITType command.
.bmtype: The MEASUrement:MEAS<x>:BMTYPe command.
.burstedgtype: The MEASUrement:MEAS<x>:BURSTEDGTYPe command.
.bvoltage: The MEASUrement:MEAS<x>:BVOLTage command.
.ccresults: The MEASUrement:MEAS<x>:CCRESUlts command tree.
.cfval: The MEASUrement:MEAS<x>:CF<x>Val command.
.clockrecovery: The MEASUrement:MEAS<x>:CLOCKRecovery command tree.
.commonmode: The MEASUrement:MEAS<x>:COMMONMode command tree.
.cover: The MEASUrement:MEAS<x>:COVer command.
.cpwidth: The MEASUrement:MEAS<x>:CPWIDTh command.
.cspacing: The MEASUrement:MEAS<x>:CSPACing command.
.customlimitsfile: The MEASUrement:MEAS<x>:CUSTOMLIMITSFile command.
.cyclemode: The MEASUrement:MEAS<x>:CYCLemode command.
.dbdown: The MEASUrement:MEAS<x>:DBDown command.
.delay: The MEASUrement:MEAS<x>:DELay command tree.
.displaystat: The MEASUrement:MEAS<x>:DISPlaystat command tree.
.dmethod: The MEASUrement:MEAS<x>:DMEThod command.
.dvds: The MEASUrement:MEAS<x>:DVDS command.
.edge: The MEASUrement:MEAS<x>:EDGE<x> command.
.edgeincre: The MEASUrement:MEAS<x>:EDGEIncre command.
.edgequalone: The MEASUrement:MEAS<x>:EDGEQUALONE command.
.edgequaltwo: The MEASUrement:MEAS<x>:EDGEQUALTWO command.
.edgequalifier: The MEASUrement:MEAS<x>:EDGEQUALifier command.
.edges: The MEASUrement:MEAS<x>:EDGES command tree.
.eequal: The MEASUrement:MEAS<x>:EEQUal command.
.einductance: The MEASUrement:MEAS<x>:EINDuctance command.
.einterpolation: The MEASUrement:MEAS<x>:EINTerpolation command.
.extenduis: The MEASUrement:MEAS<x>:EXTENDuis command.
.eyerender: The MEASUrement:MEAS<x>:EYERender command.
.failcount: The MEASUrement:MEAS<x>:FAILCount command.
.fcount: The MEASUrement:MEAS<x>:FCOunt command.
.filterrangefrom: The MEASUrement:MEAS<x>:FILTERRANGEFROM command.
.filterrangeto: The MEASUrement:MEAS<x>:FILTERRANGETO command.
.filters: The MEASUrement:MEAS<x>:FILTers command tree.
.forder: The MEASUrement:MEAS<x>:FORDer command.
.fparameter: The MEASUrement:MEAS<x>:FPARAmeter command.
.freq: The MEASUrement:MEAS<x>:FREQ command.
.fromedgesearchdirect: The MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.
.fromsymbol: The MEASUrement:MEAS<x>:FROMSymbol command tree.
.fromedge: The MEASUrement:MEAS<x>:FROMedge command.
.ftype: The MEASUrement:MEAS<x>:FTYPe command.
.fundcurrent: The MEASUrement:MEAS<x>:FUNDCURRent command.
.gating: The MEASUrement:MEAS<x>:GATing command.
.globalref: The MEASUrement:MEAS<x>:GLOBalref command.
.harmonicsclass: The MEASUrement:MEAS<x>:HARMONICSCLass command.
.harmonicssource: The MEASUrement:MEAS<x>:HARMONICSSOURce command.
.harmonicsstd: The MEASUrement:MEAS<x>:HARMONICSStd command.
.harmonicsunits: The MEASUrement:MEAS<x>:HARMONICSUNits command.
.highlevel: The MEASUrement:MEAS<x>:HIGHLEVel command tree.
.highrefvoltage: The MEASUrement:MEAS<x>:HIGHREFVoltage command.
.hlevel: The MEASUrement:MEAS<x>:HLEVel command tree.
.htorque: The MEASUrement:MEAS<x>:HTORque command.
.hvoltage: The MEASUrement:MEAS<x>:HVOLtage command.
.idletime: The MEASUrement:MEAS<x>:IDLETime command.
.inputlevel: The MEASUrement:MEAS<x>:INPUTLEVel command.
.inputpower: The MEASUrement:MEAS<x>:INPUTPOwer command.
.jittersummary: The MEASUrement:MEAS<x>:JITTERSummary command tree.
.label: The MEASUrement:MEAS<x>:LABel command.
.lineselected: The MEASUrement:MEAS<x>:LINESelected command.
.lowrefvoltage: The MEASUrement:MEAS<x>:LOWREFVoltage command.
.ltorque: The MEASUrement:MEAS<x>:LTORque command.
.ltype: The MEASUrement:MEAS<x>:LTYPe command.
.lunits: The MEASUrement:MEAS<x>:LUNITs command.
.lvoltage: The MEASUrement:MEAS<x>:LVOLtage command.
.matime: The MEASUrement:MEAS<x>:MATime command.
.maxcurrent: The MEASUrement:MEAS<x>:MAXCUrrent command.
.maxcycle: The MEASUrement:MEAS<x>:MAXCycle command.
.maxg1voltage: The MEASUrement:MEAS<x>:MAXG1Voltage command.
.maxg2voltage: The MEASUrement:MEAS<x>:MAXG2Voltage command.
.maxgvoltage: The MEASUrement:MEAS<x>:MAXGVoltage command.
.maxvoltage: The MEASUrement:MEAS<x>:MAXVoltage command.
.measrange: The MEASUrement:MEAS<x>:MEASRange command tree.
.mech: The MEASUrement:MEAS<x>:MECH command tree.
.mincycle: The MEASUrement:MEAS<x>:MINCycle command.
.nvalue: The MEASUrement:MEAS<x>:NVALUe command.
.obwmethod: The MEASUrement:MEAS<x>:OBWMethod command.
.oddeven: The MEASUrement:MEAS<x>:ODDEVen command.
.ofilters: The MEASUrement:MEAS<x>:OFILters command tree.
.osangle: The MEASUrement:MEAS<x>:OSANgle command.
.outedgequalifier: The MEASUrement:MEAS<x>:OUTEDGEQUALifier command.
.outfilters: The MEASUrement:MEAS<x>:OUTFILTers command tree.
.outputvoltage: The MEASUrement:MEAS<x>:OUTPUT<x>VOLTage command.
.passfailenabled: The MEASUrement:MEAS<x>:PASSFAILENabled command.
.passfailhighlimit: The MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.
.passfaillimit: The MEASUrement:MEAS<x>:PASSFAILLIMit command.
.passfaillowlimit: The MEASUrement:MEAS<x>:PASSFAILLOWlimit command.
.passfailmargin: The MEASUrement:MEAS<x>:PASSFAILMARgin command.
.passfailwhen: The MEASUrement:MEAS<x>:PASSFAILWHEN command.
.patterndetection: The MEASUrement:MEAS<x>:PATTERNDETECTION command.
.patternlength: The MEASUrement:MEAS<x>:PATTERNLENgth command.
.patterntype: The MEASUrement:MEAS<x>:PATTERNTYPe command.
.pcount: The MEASUrement:MEAS<x>:PCOUNt command.
.perfreq: The MEASUrement:MEAS<x>:PERFREQ command tree.
.pfrequency: The MEASUrement:MEAS<x>:PFREquency command.
.polarity: The MEASUrement:MEAS<x>:POLarity command.
.population: The MEASUrement:MEAS<x>:POPUlation command tree.
.popower: The MEASUrement:MEAS<x>:POPower command.
.powerfactor: The MEASUrement:MEAS<x>:POWERFACtor command.
.pregion: The MEASUrement:MEAS<x>:PREGion command.
.presistance: The MEASUrement:MEAS<x>:PRESistance command.
.pthreshold: The MEASUrement:MEAS<x>:PTHReshold command.
.pwidth: The MEASUrement:MEAS<x>:PWIDth command.
.redge: The MEASUrement:MEAS<x>:REDGe command.
.reflevels: The MEASUrement:MEAS<x>:REFLevels command tree.
.reflevels1: The MEASUrement:MEAS<x>:REFLevels1 command tree.
.refmode: The MEASUrement:MEAS<x>:REFMode command.
.refvoltageval: The MEASUrement:MEAS<x>:REFVOLTAGE<x>Val command.
.refvoltage: The MEASUrement:MEAS<x>:REFVoltage command.
.results: The MEASUrement:MEAS<x>:RESUlts command tree.
.rfrequency: The MEASUrement:MEAS<x>:RFREquency command.
.ripplefreqval: The MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val command.
.rrange: The MEASUrement:MEAS<x>:RRANGE command.
.sequence: The MEASUrement:MEAS<x>:SEQuence command.
.signalfrequency: The MEASUrement:MEAS<x>:SIGNALFREQUEncy command.
.signaltype: The MEASUrement:MEAS<x>:SIGNALType command.
.slabs: The MEASUrement:MEAS<x>:SLABs command.
.slpct: The MEASUrement:MEAS<x>:SLPCt command.
.sltype: The MEASUrement:MEAS<x>:SLTYpe command.
.smoothingfilter: The MEASUrement:MEAS<x>:SMOOTHINGFILTER command.
.source: The MEASUrement:MEAS<x>:SOURCE command.
.source1: The MEASUrement:MEAS<x>:SOUrce1 command.
.spanval: The MEASUrement:MEAS<x>:SPAN<x>Val command.
.srate: The MEASUrement:MEAS<x>:SRATe command.
.srho: The MEASUrement:MEAS<x>:SRHo command.
.ssc: The MEASUrement:MEAS<x>:SSC command tree.
.ssdirection: The MEASUrement:MEAS<x>:SSDirection command.
.status: The MEASUrement:MEAS<x>:STATUS command.
.stlabs: The MEASUrement:MEAS<x>:STLABs command.
.stlpct: The MEASUrement:MEAS<x>:STLPct command.
.stltype: The MEASUrement:MEAS<x>:STLTYpe command.
.stsdirection: The MEASUrement:MEAS<x>:STSDirection command.
.stype: The MEASUrement:MEAS<x>:STYPe command.
.subgroup: The MEASUrement:MEAS<x>:SUBGROUP command tree.
.sunits: The MEASUrement:MEAS<x>:SUNits command.
.tckavg: The MEASUrement:MEAS<x>:TCKAVG command.
.tconstant: The MEASUrement:MEAS<x>:TCONstant command.
.tdrpreset: The MEASUrement:MEAS<x>:TDRPreset command.
.timingmode: The MEASUrement:MEAS<x>:TIMINGMode command.
.tlevel: The MEASUrement:MEAS<x>:TLEVel command.
.tmethod: The MEASUrement:MEAS<x>:TMEThod command.
.toedgesearchdirect: The MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.
.toedge: The MEASUrement:MEAS<x>:TOEdge command.
.tosymbol: The MEASUrement:MEAS<x>:TOSYmbol command tree.
.transition: The MEASUrement:MEAS<x>:TRANSition command.
.type: The MEASUrement:MEAS<x>:TYPe command.
.vlevel: The MEASUrement:MEAS<x>:VLEVel command.
.waittime: The MEASUrement:MEAS<x>:WAITTime command.
.wbg: The MEASUrement:MEAS<x>:WBG command tree.
.width: The MEASUrement:MEAS<x>:WIDTh command.
.windowlength: The MEASUrement:MEAS<x>:WINDOWLENgth command.
.xunit: The MEASUrement:MEAS<x>:XUNIT command.
.yunit: The MEASUrement:MEAS<x>:YUNIT command.

abandwidth `property` ¶

abandwidth: MeasurementMeasItemAbandwidth

Return the MEASUrement:MEAS<x>:ABANdwidth command.

Description

This command sets or queries the analysis bandwidth for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:ABANdwidth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:ABANdwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:ABANdwidth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:ABANdwidth <NR3>
- MEASUrement:MEAS<x>:ABANdwidth?

Info

MEAS<x> specifies the measurement number.
<NR3> sets the analysis bandwidth. The default value is 10.0e6 and the valid range is 1.0e3 to 8.0e9.

achannels `property` ¶

achannels: MeasurementMeasItemAchannels

Return the MEASUrement:MEAS<x>:ACHANnels command.

Description

This command sets or queries the number of adjacent channels for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:ACHANnels? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:ACHANnels? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:ACHANnels value command.

SCPI Syntax

- MEASUrement:MEAS<x>:ACHANnels <NR3>
- MEASUrement:MEAS<x>:ACHANnels?

Info

MEAS<x> specifies the measurement number.
<NR3> sets the number of adjacent channels. The default value is 1 and the valid range is 1 to 5.

amethod `property` ¶

amethod: MeasurementMeasItemAmethod

Return the MEASUrement:MEAS<x>:AMEThod command.

Description

This command sets or queries the analysis method used to compute eye width or eye height.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:AMEThod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:AMEThod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:AMEThod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:AMEThod {PARAmetric|HISTogram}
- MEASUrement:MEAS<x>:AMEThod?

Info

MEAS<x> specifies the measurement number.
PARAmetric sets the analysis method to parametric.
HISTogram sets the analysis method to histogram.

bcount `property` ¶

bcount: MeasurementMeasItemBcount

Return the MEASUrement:MEAS<x>:BCOunt command.

Description

This command sets or returns the burst count for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BCOunt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BCOunt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BCOunt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BCOunt <NR3>
- MEASUrement:MEAS<x>:BCOunt?

Info

BCOunt specifies the burst count for WBG measurement.

bdelay `property` ¶

bdelay: MeasurementMeasItemBdelay

Return the MEASUrement:MEAS<x>:BDELay command.

Description

This command sets or returns the burst delay for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BDELay? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BDELay? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BDELay value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BDELay <NR3>
- MEASUrement:MEAS<x>:BDELay?

Info

BDELay specifies the burst delay for WBG measurement. This can be set or queried when generator type is AFG31000.

ber `property` ¶

ber: MeasurementMeasItemBer

Return the MEASUrement:MEAS<x>:BER command.

Description

This command sets or queries BER value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BER <NR3>
- MEASUrement:MEAS<x>:BER?

Info

MEAS<x> specifies the measurement number.
<NR3> is BER value for the measurement.

Sub-properties

.targetber: The MEASUrement:MEAS<x>:BER:TARGETBER command.

bin `property` ¶

bin: MeasurementMeasItemBin

Return the MEASUrement:MEAS<x>:BIN command.

Description

This command sets or queries the bin count for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BIN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BIN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BIN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BIN <NR3>
- MEASUrement:MEAS<x>:BIN?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bin count.

bitabsolute `property` ¶

bitabsolute: MeasurementMeasItemBitabsolute

Return the MEASUrement:MEAS<x>:BITAbsolute command.

Description

This command sets or queries the bit center as an absolute value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITAbsolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITAbsolute? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITAbsolute value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITAbsolute <NR3>
- MEASUrement:MEAS<x>:BITAbsolute?

Info

MEAS<x> specifies the measurement number.
<NR3> is the value for the bit center.

bitcfgmode `property` ¶

bitcfgmode: MeasurementMeasItemBitcfgmode

Return the MEASUrement:MEAS<x>:BITCfgmode command.

Description

This command sets or queries whether the measurement returns the mean or mode statistic result when the measurement type is bit amplitude/high/low. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITCfgmode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITCfgmode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITCfgmode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITCfgmode {MEAN|MODE}
- MEASUrement:MEAS<x>:BITCfgmode?

Info

MEAS<x> specifies the measurement number.
MEAN specifies that the measurement returns results for each bit.
MODE specifies that the measurement returns the mode of its results.

bitend `property` ¶

bitend: MeasurementMeasItemBitend

Return the MEASUrement:MEAS<x>:BITEnd command.

Description

This command sets or queries the bit end as a percentage of the unit interval. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITEnd? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITEnd? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITEnd value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITEnd <NR3>
- MEASUrement:MEAS<x>:BITEnd?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bit end.

bitpcnt `property` ¶

bitpcnt: MeasurementMeasItemBitpcnt

Return the MEASUrement:MEAS<x>:BITPcnt command.

Description

This command sets or queries the bit center as a percentage of the unit interval. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITPcnt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITPcnt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITPcnt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITPcnt <NR3>
- MEASUrement:MEAS<x>:BITPcnt?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bit center percentage value to be measured for the bit type selected.

bitstart `property` ¶

bitstart: MeasurementMeasItemBitstart

Return the MEASUrement:MEAS<x>:BITSTart command.

Description

This command sets or queries the bit start as a percentage of the unit interval. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITSTart? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITSTart? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITSTart value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITSTart <NR3>
- MEASUrement:MEAS<x>:BITSTart?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bit start.

bittype `property` ¶

bittype: MeasurementMeasItemBittype

Return the MEASUrement:MEAS<x>:BITType command.

Description

This command sets or queries the bit type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITType? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITType value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- MEASUrement:MEAS<x>:BITType?

Info

MEAS<x> specifies the measurement number.
ALLBits specifies that the measurement returns results for all bits.
TRANSition specifies that the measurement returns results for transitions bit only.
NONTRANsition specifies that the measurement returns results for non-transition bits only.

bmtype `property` ¶

bmtype: MeasurementMeasItemBmtype

Return the MEASUrement:MEAS<x>:BMTYPe command.

Description

Sets or queries the base measurement type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BMTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BMTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BMTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BMTYPe {TIE|PERIOD|NUInterval}
- MEASUrement:MEAS<x>:BMTYPe?

Info

MEAS<x> specifies the measurement number.
TIE specifies the base measurement type as TIE.
PERIOD specifies the base measurement type as PERIOD.
NUInterval specifies the base measurement type as NUInterval.

burstedgtype `property` ¶

burstedgtype: MeasurementMeasItemBurstedgtype

Return the MEASUrement:MEAS<x>:BURSTEDGTYPe command.

Description

This command sets or queries the burst edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?

Info

MEAS<x> specifies the measurement number.
RISE specifies a burst with a rising edge.
FALL specifies a burst with a falling edge.

bvoltage `property` ¶

bvoltage: MeasurementMeasItemBvoltage

Return the MEASUrement:MEAS<x>:BVOLTage command.

Description

This command sets or returns the bias voltage for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BVOLTage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BVOLTage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BVOLTage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BVOLTage <NR3>
- MEASUrement:MEAS<x>:BVOLTage?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for bias voltage of the WBG measurement.

ccresults `property` ¶

ccresults: MeasurementMeasItemCcresults

Return the MEASUrement:MEAS<x>:CCRESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.allacqs: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

cfval `property` ¶

cfval: dict[int, MeasurementMeasItemCfvalItem]

Return the MEASUrement:MEAS<x>:CF<x>Val command.

Description

This command sets or returns the filter count for PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CF<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CF<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CF<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CF<x>Val <NR3>
- MEASUrement:MEAS<x>:CF<x>Val?

Info

MEAS<x> specifies the measurement number.
CF<x> specifies the center frequency number.
<NR3> specifies the center frequency.

clockrecovery `property` ¶

clockrecovery: MeasurementMeasItemClockrecovery

Return the MEASUrement:MEAS<x>:CLOCKRecovery command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.advanced: The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced command tree.
.clockfrequency: The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.
.clockmultiplier: The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.
.constclockmode: The MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe command.
.damping: The MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing command.
.datapath: The MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath command.
.datarate: The MEASUrement:MEAS<x>:CLOCKRecovery:DATARate command.
.explicitclockmode: The MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe command.
.global: The MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal command.
.jtfbandwidth: The MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth command.
.loopbandwidth: The MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.
.meanautocalculate: The MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.
.method: The MEASUrement:MEAS<x>:CLOCKRecovery:METHod command.
.model: The MEASUrement:MEAS<x>:CLOCKRecovery:MODel command.
.nominaloffset: The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.
.standard: The MEASUrement:MEAS<x>:CLOCKRecovery:STAndard command.
.tdcompensation: The MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation command.

commonmode `property` ¶

commonmode: MeasurementMeasItemCommonmode

Return the MEASUrement:MEAS<x>:COMMONMode command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.filters: The MEASUrement:MEAS<x>:COMMONMode:FILTers command tree.
.sources: The MEASUrement:MEAS<x>:COMMONMode:SOURCEs command.

cover `property` ¶

cover: MeasurementMeasItemCover

Return the MEASUrement:MEAS<x>:COVer command.

Description

This command sets or queries the Calculate Over for the Power Quality measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COVer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COVer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:COVer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:COVer {FFREQuency|AFREQuencies}
- MEASUrement:MEAS<x>:COVer?

Info

FFREQuency sets Calculate Power Quality measurement.
AFREQuencies sets Calculate Power Quality measurement for all frequencies.

cpwidth `property` ¶

cpwidth: MeasurementMeasItemCpwidth

Return the MEASUrement:MEAS<x>:CPWIDTh command.

Description

This command sets or queries the channel power width for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CPWIDTh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CPWIDTh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CPWIDTh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CPWIDTh <NR3>
- MEASUrement:MEAS<x>:CPWIDTh?

Info

<NR3> is the channel power width. The default value is 10.0e6 and the valid range is 1.0e3 to 8.0e9.

cspacing `property` ¶

cspacing: MeasurementMeasItemCspacing

Return the MEASUrement:MEAS<x>:CSPACing command.

Description

This command sets or queries the channel spacing for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CSPACing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CSPACing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CSPACing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CSPACing <NR3>
- MEASUrement:MEAS<x>:CSPACing?

Info

<NR3> is the channel spacing. The default value is 5.0e6 and the valid range is 1.0e3 to 8.0e9.

customlimitsfile `property` ¶

customlimitsfile: MeasurementMeasItemCustomlimitsfile

Return the MEASUrement:MEAS<x>:CUSTOMLIMITSFile command.

Description

This command sets or queries the custom limits file path for custom harmonics standard. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CUSTOMLIMITSFile? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CUSTOMLIMITSFile? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CUSTOMLIMITSFile value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CUSTOMLIMITSFile <QString>
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile?

Info

MEAS<x> specifies the measurement number.
<QString> specifies the location of limits file.

cyclemode `property` ¶

cyclemode: MeasurementMeasItemCyclemode

Return the MEASUrement:MEAS<x>:CYCLemode command.

Description

This command sets or queries the cycle mode for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CYCLemode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CYCLemode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CYCLemode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CYCLemode {RECORD|CYCLE|ROTATION}
- MEASUrement:MEAS<x>:CYCLemode?

Info

MEAS<x> specifies the measurement number.
RECORD specifies that the measurement is taken over the whole record.
CYCLE specifies that measurements are taken on each cycle of the source.
ROTATION specifies that measurements are taken on a rotation of the source.

dbdown `property` ¶

dbdown: MeasurementMeasItemDbdown

Return the MEASUrement:MEAS<x>:DBDown command.

Description

This command sets or queries the dB down value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DBDown? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DBDown? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DBDown value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DBDown <NR3>
- MEASUrement:MEAS<x>:DBDown?

Info

<NR3> sets the dB down value. The default value is -26 and the valid range is -80 to -1.

delay `property` ¶

delay: MeasurementMeasItemDelay

Return the MEASUrement:MEAS<x>:DELay command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.edge: The MEASUrement:MEAS<x>:DELay:EDGE<x> command.

displaystat `property` ¶

displaystat: MeasurementMeasItemDisplaystat

Return the MEASUrement:MEAS<x>:DISPlaystat command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.enable: The MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

dmethod `property` ¶

dmethod: MeasurementMeasItemDmethod

Return the MEASUrement:MEAS<x>:DMEThod command.

Description

This command sets or returns the deskew method for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DMEThod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DMEThod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DMEThod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DMEThod {AUTO|MANual}
- MEASUrement:MEAS<x>:DMEThod?

Info

AUTO or MANual specifies the deskew method set for WBG measurement.

dvds `property` ¶

dvds: MeasurementMeasItemDvds

Return the MEASUrement:MEAS<x>:DVDS command.

Description

This command enabled or disables display state of the derived Vds waveform for RDS(on) measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DVDS? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DVDS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DVDS value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DVDS {OFF|ON}
- MEASUrement:MEAS<x>:DVDS?

Info

MEAS<x> specifies the measurement number.
OFF specifies that derived Vds waveform display is disabled for RDS(on) measurement.
ON specifies that derived Vds waveform display is enabled for RDS(on) measurement.

edge `property` ¶

edge: dict[int, MeasurementMeasItemEdgeItem]

Return the MEASUrement:MEAS<x>:EDGE<x> command.

Description

This command sets or queries the type of the specified edge, rise or fall, for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:MEAS<x>:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
RISE specifies the rising edge.
FALL specifies the falling edge.
BOTH specifies either the rising or falling edge.

edgeincre `property` ¶

edgeincre: MeasurementMeasItemEdgeincre

Return the MEASUrement:MEAS<x>:EDGEIncre command.

Description

This command sets or queries the edge increment value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEIncre? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEIncre? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEIncre value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?

Info

MEAS<x> specifies the measurement number.
<NR3> is the measurements edge increment value.

edgequalifier `property` ¶

edgequalifier: MeasurementMeasItemEdgequalifier

Return the MEASUrement:MEAS<x>:EDGEQUALifier command.

Description

This command sets or queries the edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEQUALifier value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:EDGEQUALifier?

Info

MEAS<x> is the measurement number.
CH<x> is the edge qualifier source channel.
MATH<x> is the edge qualifier source math waveform; is ≥1.
REF<x> is the edge qualifier source reference waveform; is ≥1.

edgequalone `property` ¶

edgequalone: MeasurementMeasItemEdgequalone

Return the MEASUrement:MEAS<x>:EDGEQUALONE command.

Description

This command set or queries the measurement 1 input edge qualifier one source for Efficiency measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEQUALONE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEQUALONE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEQUALONE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEQUALONE <QString>
- MEASUrement:MEAS<x>:EDGEQUALONE?

Info

MEAS<x> is the measurement number.
<QString> specifies the edge qualifier source at input configuration.

edgequaltwo `property` ¶

edgequaltwo: MeasurementMeasItemEdgequaltwo

Return the MEASUrement:MEAS<x>:EDGEQUALTWO command.

Description

This command sets or queries the measurement 1 output edge qualifier two source for Efficiency measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEQUALTWO? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEQUALTWO? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEQUALTWO value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEQUALTWO <QString>
- MEASUrement:MEAS<x>:EDGEQUALTWO?

Info

MEAS<x> is the measurement number.
<QString> specifies the edge qualifier source at output configuration.

edges `property` ¶

edges: MeasurementMeasItemEdges

Return the MEASUrement:MEAS<x>:EDGES command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.fromlevel: The MEASUrement:MEAS<x>:EDGES:FROMLevel command.
.level: The MEASUrement:MEAS<x>:EDGES:LEVel command.
.lowerfrequency: The MEASUrement:MEAS<x>:EDGES:LOWERFREQuency command.
.n: The MEASUrement:MEAS<x>:EDGES:N command.
.slewratemethod: The MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.
.tolevel: The MEASUrement:MEAS<x>:EDGES:TOLevel command.
.upperfrequency: The MEASUrement:MEAS<x>:EDGES:UPPERFREQuency command.

eequal `property` ¶

eequal: MeasurementMeasItemEequal

Return the MEASUrement:MEAS<x>:EEQUal command.

Description

This command turns on or off the edge qualifier settings as input waveform to measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EEQUal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EEQUal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EEQUal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EEQUal {ON|OFF}
- MEASUrement:MEAS<x>:EEQUal?

Info

MEAS<x> specifies the measurement number.
ON specifies the edge qualifier settings has been turned on.
OFF specifies the edge qualifier settings has been turned off.

einductance `property` ¶

einductance: MeasurementMeasItemEinductance

Return the MEASUrement:MEAS<x>:EINDuctance command.

Description

This command sets or returns the effective inductance for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EINDuctance? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EINDuctance? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EINDuctance value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EINDuctance <NR3>
- MEASUrement:MEAS<x>:EINDuctance?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for effective inductance of the WBG measurement.

einterpolation `property` ¶

einterpolation: MeasurementMeasItemEinterpolation

Return the MEASUrement:MEAS<x>:EINTerpolation command.

Description

This command sets or queries whether dot mode eye diagram is enabled.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EINTerpolation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EINTerpolation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EINTerpolation value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EINTerpolation {ON|OFF}
- MEASUrement:MEAS<x>:EINTerpolation?

Info

MEAS<x> specifies the measurement number.
ON enables interpolation between samples.
OFF disables interpolation between samples.

extenduis `property` ¶

extenduis: MeasurementMeasItemExtenduis

Return the MEASUrement:MEAS<x>:EXTENDuis command.

Description

This command sets or returns number of UIs considered for analysis of eye width or eye height measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EXTENDuis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EXTENDuis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EXTENDuis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EXTENDuis <NR1>
- MEASUrement:MEAS<x>:EXTENDuis?

Info

MEAS<x> specifies the measurement number.
<NR1> is the number of UIs considered for analysis.

eyerender `property` ¶

eyerender: MeasurementMeasItemEyerender

Return the MEASUrement:MEAS<x>:EYERender command.

Description

This command sets or queries the eye rendering method.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EYERender? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EYERender? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EYERender value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EYERender {FAst|COMPlete}
- MEASUrement:MEAS<x>:EYERender?

Info

MEAS<x> specifies the measurement number.
FAst sets the eye rendering method to fast.
COMPlete sets the eye rendering method to complete.

failcount `property` ¶

failcount: MeasurementMeasItemFailcount

Return the MEASUrement:MEAS<x>:FAILCount command.

Description

This command returns the number of measurement failures, if applicable, for the selected measure The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FAILCount? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FAILCount? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:FAILCount?

fcount `property` ¶

fcount: MeasurementMeasItemFcount

Return the MEASUrement:MEAS<x>:FCOunt command.

Description

This command sets or returns the filter count for PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FCOunt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FCOunt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FCOunt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FCOunt <NR3>
- MEASUrement:MEAS<x>:FCOunt?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the number of filters applied for PSIJ measurement.

filterrangefrom `property` ¶

filterrangefrom: MeasurementMeasItemFilterrangefrom

Return the MEASUrement:MEAS<x>:FILTERRANGEFROM command.

Description

This command sets or queries harmonics filter from order. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTERRANGEFROM? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTERRANGEFROM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTERRANGEFROM value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTERRANGEFROM <NR3>
- MEASUrement:MEAS<x>:FILTERRANGEFROM?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the filter range from value. The default value is 1.

filterrangeto `property` ¶

filterrangeto: MeasurementMeasItemFilterrangeto

Return the MEASUrement:MEAS<x>:FILTERRANGETO command.

Description

This command sets or queries harmonics filter to order. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTERRANGETO? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTERRANGETO? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTERRANGETO value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTERRANGETO <NR3>
- MEASUrement:MEAS<x>:FILTERRANGETO?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the filter range to value. The default value is 50.

filters `property` ¶

filters: MeasurementMeasItemFilters

Return the MEASUrement:MEAS<x>:FILTers command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.blankingtime: The MEASUrement:MEAS<x>:FILTers:BLANKingtime command.
.global: The MEASUrement:MEAS<x>:FILTers:GLOBal command.
.highpass: The MEASUrement:MEAS<x>:FILTers:HIGHPass command tree.
.lowpass: The MEASUrement:MEAS<x>:FILTers:LOWPass command tree.
.ramptime: The MEASUrement:MEAS<x>:FILTers:RAMPtime command.

forder `property` ¶

forder: MeasurementMeasItemForder

Return the MEASUrement:MEAS<x>:FORDer command.

Description

This command sets or returns the differential filter order for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FORDer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FORDer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FORDer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FORDer <NR3>
- MEASUrement:MEAS<x>:FORDer?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the differential filter order of the WBG measurement.

fparameter `property` ¶

fparameter: MeasurementMeasItemFparameter

Return the MEASUrement:MEAS<x>:FPARAmeter command.

Description

This command sets or queries the roll off factor for the RRC filter in the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FPARAmeter? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FPARAmeter? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FPARAmeter value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FPARAmeter <NR3>
- MEASUrement:MEAS<x>:FPARAmeter?

Info

<NR3> sets the roll off factor. The default is 0.22. The valid range is from 0.001 to 1.0.

freq `property` ¶

freq: MeasurementMeasItemFreq

Return the MEASUrement:MEAS<x>:FREQ command.

Description

This command sets or queries switching frequency for Switching Ripple measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FREQ <NR3>
- MEASUrement:MEAS<x>:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the switching frequency. The default is 100k Hz, The minimum is 50 Hz, and the maximum is 1 GHz.

fromedge `property` ¶

fromedge: MeasurementMeasItemFromedge

Return the MEASUrement:MEAS<x>:FROMedge command.

Description

This command sets or queries the from edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMedge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMedge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMedge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISe specifies the rising edge of the waveform.
BOTH specifies both the rising and falling edges of the waveform.

fromedgesearchdirect `property` ¶

fromedgesearchdirect: MeasurementMeasItemFromedgesearchdirect

Return the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.

Description

This command sets or queries the from edge search direction for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search from the edge.
BACKWard specifies a backward search from the edge.

fromsymbol `property` ¶

fromsymbol: MeasurementMeasItemFromsymbol

Return the MEASUrement:MEAS<x>:FROMSymbol command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.logic2source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce command.
.logic3source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce command.
.logic4source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce command.
.logic5source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce command.
.measureat: The MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT command.

ftype `property` ¶

ftype: MeasurementMeasItemFtype

Return the MEASUrement:MEAS<x>:FTYPe command.

Description

This command sets or returns whether the RRC filter is enabled or not. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FTYPe {True|False}
- MEASUrement:MEAS<x>:FTYPe?

Info

True enables the RRC filter.
False disables the RRC filter.

fundcurrent `property` ¶

fundcurrent: MeasurementMeasItemFundcurrent

Return the MEASUrement:MEAS<x>:FUNDCURRent command.

Description

This command sets or queries the fundamental current value for IEC-Class C type harmonics standard. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FUNDCURRent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FUNDCURRent? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FUNDCURRent value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FUNDCURRent <NR3>
- MEASUrement:MEAS<x>:FUNDCURRent?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the fundamental current for class C harmonics standard.

gating `property` ¶

gating: MeasurementMeasItemGating

Return the MEASUrement:MEAS<x>:GATing command.

Description

This command sets or queries the gating type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing?

Info

MEAS<x> is the measurement number for which to return a value.
NONE specifies measurements are taken across the entire record.
SCREEN turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only when the logical state of other waveforms is true.
SEARch specifies that measurements are taken only where the results of a user specified search are found.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Sub-properties

.active: The MEASUrement:MEAS<x>:GATing:ACTive command.
.endtime: The MEASUrement:MEAS<x>:GATing:ENDtime command.
.global: The MEASUrement:MEAS<x>:GATing:GLOBal command.
.hysteresis: The MEASUrement:MEAS<x>:GATing:HYSTeresis command.
.logicsource: The MEASUrement:MEAS<x>:GATing:LOGICSource command.
.midref: The MEASUrement:MEAS<x>:GATing:MIDRef command.
.searchsource: The MEASUrement:MEAS<x>:GATing:SEARCHSource command.
.starttime: The MEASUrement:MEAS<x>:GATing:STARTtime command.

globalref `property` ¶

globalref: MeasurementMeasItemGlobalref

Return the MEASUrement:MEAS<x>:GLOBalref command.

Description

This command sets or queries the reference levels global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GLOBalref? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GLOBalref? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GLOBalref value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?

Info

MEAS<x> specifies the measurement number.
OFF allows ref levels to be set separately for each measurement.
ON applies the same ref levels to all measurements.
0 allows ref levels to be set separately for each measurement.
1 applies the same ref levels to all measurements.

harmonicsclass `property` ¶

harmonicsclass: MeasurementMeasItemHarmonicsclass

Return the MEASUrement:MEAS<x>:HARMONICSCLass command.

Description

This command sets or queries the class type for the harmonics measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSCLass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSCLass? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSCLass value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSCLass {CLASSA|CLASSB|CLASSC|CLASSD}
- MEASUrement:MEAS<x>:HARMONICSCLass?

Info

MEAS<x> specifies the measurement number.
CLASSA specifies the class type to A.
CLASSB specifies the class type to B.
CLASSC specifies the class type to C.
CLASSD specifies the class type to D.

harmonicssource `property` ¶

harmonicssource: MeasurementMeasItemHarmonicssource

Return the MEASUrement:MEAS<x>:HARMONICSSOURce command.

Description

This command sets or queries harmonics source. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSSOURce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSSOURce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSSOURce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSSOURce {CURRENT|VOLTAGE}
- MEASUrement:MEAS<x>:HARMONICSSOURce?

Info

MEAS<x> specifies the measurement number.
CURRENT specifies current as the harmonics source.
VOLTAGE specifies voltage as the harmonics source.

harmonicsstd `property` ¶

harmonicsstd: MeasurementMeasItemHarmonicsstd

Return the MEASUrement:MEAS<x>:HARMONICSStd command.

Description

This command sets or queries harmonics standard. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSStd? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSStd? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSStd value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSStd {NONE|IEC|IEEE519|CUSTOM|REVIEEE5192022}
- MEASUrement:MEAS<x>:HARMONICSStd?

Info

MEAS<x> specifies the measurement number.
NONE specifies none as the harmonics test standard.
IEC specifies IEC as the harmonics test standard.
IEEE519 specifies IEEE519 as the harmonics test standard.
REVIEEE5192022 specifies REVIEEE5192022 as the harmonics test standard.
CUSTOM specifies that there is a custom harmonics test standard.

harmonicsunits `property` ¶

harmonicsunits: MeasurementMeasItemHarmonicsunits

Return the MEASUrement:MEAS<x>:HARMONICSUNits command.

Description

This command sets or queries harmonics units. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSUNits? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSUNits value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSUNits {LOGARITHM|LINEAR}
- MEASUrement:MEAS<x>:HARMONICSUNits?

Info

MEAS<x> specifies the measurement number.
LOGARITHM specifies logarithmic as the harmonics units.
LINEAR specifies linear as the harmonics units.

highlevel `property` ¶

highlevel: MeasurementMeasItemHighlevel

Return the MEASUrement:MEAS<x>:HIGHLEVel command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.configuration: The MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration command.
.l2ltol2n: The MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N command.
.lineselected: The MEASUrement:MEAS<x>:HIGHLEVel:LINESelected command.
.outl2ltol2n: The MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N command.
.outlineselected: The MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected command.
.outwiring: The MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing command.
.useglobal: The MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL command.
.wiring: The MEASUrement:MEAS<x>:HIGHLEVel:WIRing command.

highrefvoltage `property` ¶

highrefvoltage: MeasurementMeasItemHighrefvoltage

Return the MEASUrement:MEAS<x>:HIGHREFVoltage command.

Description

This command sets or queries the high reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference voltage value for the selected configuration.

hlevel `property` ¶

hlevel: MeasurementMeasItemHlevel

Return the MEASUrement:MEAS<x>:HLEVel command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HLEVel? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.output: The MEASUrement:MEAS<x>:HLEVel:OUTPut command tree.

htorque `property` ¶

htorque: MeasurementMeasItemHtorque

Return the MEASUrement:MEAS<x>:HTORque command.

Description

This command sets or queries the measurement High Torque value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HTORque? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HTORque? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HTORque value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HTORque <NR1>
- MEASUrement:MEAS<x>:HTORque?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the High Torque value of the measurement in the range of 11 to 10000000.

hvoltage `property` ¶

hvoltage: MeasurementMeasItemHvoltage

Return the MEASUrement:MEAS<x>:HVOLtage command.

Description

This command sets or queries the measurement Torque High Voltage value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HVOLtage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HVOLtage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HVOLtage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HVOLtage <NR1>
- MEASUrement:MEAS<x>:HVOLtage?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the High Voltage value of the measurement in the range of 1 to 100.

idletime `property` ¶

idletime: MeasurementMeasItemIdletime

Return the MEASUrement:MEAS<x>:IDLETime command.

Description

This command sets or queries the idle time for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:IDLETime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:IDLETime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:IDLETime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the idle time.

inputlevel `property` ¶

inputlevel: MeasurementMeasItemInputlevel

Return the MEASUrement:MEAS<x>:INPUTLEVel command.

Description

Sets or queries the input trigger voltage level.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:INPUTLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:INPUTLEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:INPUTLEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:INPUTLEVel <NR2>
- MEASUrement:MEAS<x>:INPUTLEVel?

Info

MEAS<x> is the measurement number.
<NR2> is the trigger voltage, in the range of -500 V to +500 V.

inputpower `property` ¶

inputpower: MeasurementMeasItemInputpower

Return the MEASUrement:MEAS<x>:INPUTPOwer command.

Description

This command sets or queries the input power value for IEC-Class C and Class D harmonics standard.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:INPUTPOwer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:INPUTPOwer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:INPUTPOwer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:INPUTPOwer <NR3>
- MEASUrement:MEAS<x>:INPUTPOwer?

Info

MEAS<x> is the measurement number.
<NR3> specifies the input power value for class C harmonics standard.

jittersummary `property` ¶

jittersummary: MeasurementMeasItemJittersummary

Return the MEASUrement:MEAS<x>:JITTERSummary command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.dcd: The MEASUrement:MEAS<x>:JITTERSummary:DCD command.
.ddj: The MEASUrement:MEAS<x>:JITTERSummary:DDJ command.
.dj: The MEASUrement:MEAS<x>:JITTERSummary:DJ command.
.djdd: The MEASUrement:MEAS<x>:JITTERSummary:DJDD command.
.dr: The MEASUrement:MEAS<x>:JITTERSummary:DR command.
.eyewidthber: The MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER command.
.isi: The MEASUrement:MEAS<x>:JITTERSummary:ISI command.
.npj: The MEASUrement:MEAS<x>:JITTERSummary:NPJ command.
.pj: The MEASUrement:MEAS<x>:JITTERSummary:PJ command.
.pl: The MEASUrement:MEAS<x>:JITTERSummary:PL command.
.rj: The MEASUrement:MEAS<x>:JITTERSummary:RJ command.
.rjdd: The MEASUrement:MEAS<x>:JITTERSummary:RJDD command.
.tie: The MEASUrement:MEAS<x>:JITTERSummary:TIE command.
.tjber: The MEASUrement:MEAS<x>:JITTERSummary:TJBER command.

label `property` ¶

label: MeasurementMeasItemLabel

Return the MEASUrement:MEAS<x>:LABel command.

Description

This command sets or queries the label for the measurement. As the label can contain non 7-bit ASCII text, it is stored in Percent Encoding format. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LABel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LABel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LABel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LABel <QString>
- MEASUrement:MEAS<x>:LABel?

Info

MEAS<x> specifies the measurement number.
<QString> is the measurement label.

lineselected `property` ¶

lineselected: MeasurementMeasItemLineselected

Return the MEASUrement:MEAS<x>:LINESelected command.

Description

This command sets or queries selected lines for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LINESelected? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LINESelected value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LINESelected {ABCB|ACBC|BACA|XYZY|XZYZ|YXZX}
- MEASUrement:MEAS<x>:LINESelected?

Info

MEAS<x> specifies the measurement number.
ABCB specifies the selected lines as ABCB.
ACBC specifies the selected lines as ACBC.
BACA specifies the selected lines as BACA.
XYZY specifies the selected lines as XYZY.
XZYZ specifies the selected lines as XZYZ.
YXZX specifies the selected lines as YXZX.

lowrefvoltage `property` ¶

lowrefvoltage: MeasurementMeasItemLowrefvoltage

Return the MEASUrement:MEAS<x>:LOWREFVoltage command.

Description

This command sets or queries the low reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference voltage value for the selected configuration.

ltorque `property` ¶

ltorque: MeasurementMeasItemLtorque

Return the MEASUrement:MEAS<x>:LTORque command.

Description

This command sets or queries the measurement Low Torque value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LTORque? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LTORque? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LTORque value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LTORque <NR1>
- MEASUrement:MEAS<x>:LTORque?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the Low Torque value of the measurement in the range of 0 to 10000000.

ltype `property` ¶

ltype: MeasurementMeasItemLtype

Return the MEASUrement:MEAS<x>:LTYPe command.

Description

This command sets or returns the value for the level type as auto or custom. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LTYPe {AUTO|CUSTom}
- MEASUrement:MEAS<x>:LTYPe?

Info

AUTO specifies the value for the level type as auto.
CUSTom specifies the value for the level type as custom.

lunits `property` ¶

lunits: MeasurementMeasItemLunits

Return the MEASUrement:MEAS<x>:LUNITs command.

Description

This command sets or returns the value for the level units as percentage or absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LUNITs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LUNITs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LUNITs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LUNITs {PERCent|ABSolute}
- MEASUrement:MEAS<x>:LUNITs?

Info

PERCent specifies the value for the level units as percent.
ABSolute specifies the value for the level units as absolute.

lvoltage `property` ¶

lvoltage: MeasurementMeasItemLvoltage

Return the MEASUrement:MEAS<x>:LVOLtage command.

Description

This command sets or queries the measurement Torque Low Voltage value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LVOLtage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LVOLtage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LVOLtage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LVOLtage <NR1>
- MEASUrement:MEAS<x>:LVOLtage?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the Low Voltage value of the measurement in the range of -100 to 100.

matime `property` ¶

matime: MeasurementMeasItemMatime

Return the MEASUrement:MEAS<x>:MATime command.

Description

This command sets or returns the maximum acquisition time for WBG measurement. This should be set only if AFG is not AFG31000.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MATime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MATime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MATime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MATime <NR3>
- MEASUrement:MEAS<x>:MATime?

Info

MATime specifies the maximum acquisition time for WBG measurement.

maxcurrent `property` ¶

maxcurrent: MeasurementMeasItemMaxcurrent

Return the MEASUrement:MEAS<x>:MAXCUrrent command.

Description

This command sets or returns the maximum current. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXCUrrent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXCUrrent? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXCUrrent value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXCUrrent <NR3>
- MEASUrement:MEAS<x>:MAXCUrrent?

Info

<NR3> specifies the maximum current.

maxcycle `property` ¶

maxcycle: MeasurementMeasItemMaxcycle

Return the MEASUrement:MEAS<x>:MAXCycle command.

Description

This command sets or queries the maximum cycle value for the DDRTERRN and DDRTERRMN measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXCycle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXCycle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXCycle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXCycle <NR1>
- MEASUrement:MEAS<x>:MAXCycle?

Info

MEAS<x> specifies the measurement number.
<NR1> is the maximum cycle range limit value in the range or 2 to 50.

maxg1voltage `property` ¶

maxg1voltage: MeasurementMeasItemMaxg1voltage

Return the MEASUrement:MEAS<x>:MAXG1Voltage command.

Description

This command sets or returns the maximum gate voltage 1 or 2 value for Tdt measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXG1Voltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXG1Voltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXG1Voltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXG1Voltage <NR3>
- MEASUrement:MEAS<x>:MAXG1Voltage?

Info

<NR3> specifies the maximum gate voltage.

maxg2voltage `property` ¶

maxg2voltage: MeasurementMeasItemMaxg2voltage

Return the MEASUrement:MEAS<x>:MAXG2Voltage command.

Description

This command sets or returns the maximum gate voltage 1 or 2 value for Tdt measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXG2Voltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXG2Voltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXG2Voltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXG2Voltage <NR3>
- MEASUrement:MEAS<x>:MAXG2Voltage?

Info

<NR3> specifies the maximum gate voltage.

maxgvoltage `property` ¶

maxgvoltage: MeasurementMeasItemMaxgvoltage

Return the MEASUrement:MEAS<x>:MAXGVoltage command.

Description

This command sets or returns the maximum gate voltage. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXGVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXGVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXGVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXGVoltage <NR3>
- MEASUrement:MEAS<x>:MAXGVoltage?

Info

<NR3> specifies the maximum gate voltage.

maxvoltage `property` ¶

maxvoltage: MeasurementMeasItemMaxvoltage

Return the MEASUrement:MEAS<x>:MAXVoltage command.

Description

Sets or queries the maximum input voltage. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXVoltage <NR2>
- MEASUrement:MEAS<x>:MAXVoltage?

Info

<NR2> is the maximum input voltage, in the range of -61 V to +61 V.

measrange `property` ¶

measrange: MeasurementMeasItemMeasrange

Return the MEASUrement:MEAS<x>:MEASRange command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.global: The MEASUrement:MEAS<x>:MEASRange:GLOBal command.
.max: The MEASUrement:MEAS<x>:MEASRange:MAX command.
.min: The MEASUrement:MEAS<x>:MEASRange:MIN command.
.state: The MEASUrement:MEAS<x>:MEASRange:STATE command.

mech `property` ¶

mech: MeasurementMeasItemMech

Return the MEASUrement:MEAS<x>:MECH command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.eindexz: The MEASUrement:MEAS<x>:MECH:EINDexz command.
.gratio: The MEASUrement:MEAS<x>:MECH:GRATio command.
.munits: The MEASUrement:MEAS<x>:MECH:MUNits command.
.ppairs: The MEASUrement:MEAS<x>:MECH:PPAirs command.
.pprotation: The MEASUrement:MEAS<x>:MECH:PPRotation command.
.stype: The MEASUrement:MEAS<x>:MECH:STYPe command.

mincycle `property` ¶

mincycle: MeasurementMeasItemMincycle

Return the MEASUrement:MEAS<x>:MINCycle command.

Description

This command sets or queries the minimum cycle value for the DDRTERRN and DDRTERRMN measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MINCycle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MINCycle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MINCycle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MINCycle <NR1>
- MEASUrement:MEAS<x>:MINCycle?

Info

MEAS<x> specifies the measurement number.
<NR1> is the minimum cycle range limit value in the range or 2 to 50.

nvalue `property` ¶

nvalue: MeasurementMeasItemNvalue

Return the MEASUrement:MEAS<x>:NVALUe command.

Description

Sets or queries the number of unit intervals used for the Base Measurement Type of NUnitInterval.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:NVALUe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:NVALUe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:NVALUe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:NVALUe <N>
- MEASUrement:MEAS<x>:NVALUe?

Info

MEAS<x> specifies the measurement number.
<N> specifies the number of unit intervals.

obwmethod `property` ¶

obwmethod: MeasurementMeasItemObwmethod

Return the MEASUrement:MEAS<x>:OBWMethod command.

Description

This command sets or queries the RF measurement Occupied Bandwidth method type. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OBWMethod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OBWMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OBWMethod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OBWMethod {percOfPwr|dBDown}
- MEASUrement:MEAS<x>:OBWMethod?

Info

percOfPwr specifies the method type as percentage of power. This is the default value.
dBDown specifies the method type as dB down.

oddeven `property` ¶

oddeven: MeasurementMeasItemOddeven

Return the MEASUrement:MEAS<x>:ODDEVen command.

Description

This command sets or queries harmonics oddeven.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:ODDEVen? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:ODDEVen? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:ODDEVen value command.

SCPI Syntax

- MEASUrement:MEAS<x>:ODDEVen {ALL|EVEN|ODD}
- MEASUrement:MEAS<x>:ODDEVen?

Info

MEAS<x> specifies the measurement number.
ALL displays all the results.
EVEN displays the even results.
ODD displays the odd results.

ofilters `property` ¶

ofilters: MeasurementMeasItemOfilters

Return the MEASUrement:MEAS<x>:OFILters command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.lowpass: The MEASUrement:MEAS<x>:OFILters:LOWPass command tree.

osangle `property` ¶

osangle: MeasurementMeasItemOsangle

Return the MEASUrement:MEAS<x>:OSANgle command.

Description

This command sets or queries the specified measurement Offset angle.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OSANgle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OSANgle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OSANgle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OSANgle <NR1>
- MEASUrement:MEAS<x>:OSANgle?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the offset angle of the measurement in the range or -360 to 360.

outedgequalifier `property` ¶

outedgequalifier: MeasurementMeasItemOutedgequalifier

Return the MEASUrement:MEAS<x>:OUTEDGEQUALifier command.

Description

This command sets or queries local output edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTEDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTEDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTEDGEQUALifier value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTEDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:OUTEDGEQUALifier?

Info

MEAS<x> specifies the measurement number.
CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

outfilters `property` ¶

outfilters: MeasurementMeasItemOutfilters

Return the MEASUrement:MEAS<x>:OUTFILTers command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.lowpass: The MEASUrement:MEAS<x>:OUTFILTers:LOWPass command tree.

outputvoltage `property` ¶

outputvoltage: dict[int, MeasurementMeasItemOutputvoltageItem]

Return the MEASUrement:MEAS<x>:OUTPUT<x>VOLTage command.

Description

Sets or queries the voltage level for the specified output voltage source n.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTPUT<x>VOLTage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTPUT<x>VOLTage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTPUT<x>VOLTage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTPUT<x>VOLTage <NR2>
- MEASUrement:MEAS<x>:OUTPUT<x>VOLTage?

Info

MEAS<x> specifies the measurement number.
<NR2> is the output voltage for source n, in the range of -61 V to +61 V.

passfailenabled `property` ¶

passfailenabled: MeasurementMeasItemPassfailenabled

Return the MEASUrement:MEAS<x>:PASSFAILENabled command.

Description

This command returns or sets the pass/fail test enable status. If enabled, this will turn on pass fail testing for the specified measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?

Info

<NR1> enables or disables pass fail testing for the specified measurement. A value of 1 enables and a value of 0 disables.

passfailhighlimit `property` ¶

passfailhighlimit: MeasurementMeasItemPassfailhighlimit

Return the MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.

Description

This command returns or sets the high limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?

Info

<NR2> sets the high limit for a measurement test. The high limit is a number which a measurement result will be tested against.

passfaillimit `property` ¶

passfaillimit: MeasurementMeasItemPassfaillimit

Return the MEASUrement:MEAS<x>:PASSFAILLIMit command.

Description

This command returns or sets the limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?

Info

<NR2> sets the limit for a measurement test. The limit is a number which a measurement result will be tested against.

passfaillowlimit `property` ¶

passfaillowlimit: MeasurementMeasItemPassfaillowlimit

Return the MEASUrement:MEAS<x>:PASSFAILLOWlimit command.

Description

This command returns or sets the low limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?

Info

<NR2> sets the low limit for a measurement test. The limit is a number which a measurement result will be tested against.

passfailmargin `property` ¶

passfailmargin: MeasurementMeasItemPassfailmargin

Return the MEASUrement:MEAS<x>:PASSFAILMARgin command.

Description

This command returns or sets the allowed margin for limit comparisons for all pass/fail checks. This is given as a percentage with a default value of 0.05 representing 5%. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?

Info

<NR2> sets the allowed margin for limit comparisons for all pass/fail checks. The margin as a percentage of the limit.

passfailwhen `property` ¶

passfailwhen: MeasurementMeasItemPassfailwhen

Return the MEASUrement:MEAS<x>:PASSFAILWHEN command.

Description

This command sets or returns the condition on which a measurement test fails. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?

Info

LESSthan sets the condition for measurement test failure as less than the given limit. This is the default value.
GREATERthan sets the condition for measurement test failure as greater than the given limit.
Equals sets the condition for measurement test failure as equals the given limit.
NOTEQuals sets the condition for measurement test failure as not equal to the given limit.
INSIDErange sets the condition for measurement test failure as inside the limit range.
OUTSIDErange sets the condition for measurement test failure as outside the limit range.

patterndetection `property` ¶

patterndetection: MeasurementMeasItemPatterndetection

Return the MEASUrement:MEAS<x>:PATTERNDETECTION command.

Description

This command sets or queries the pattern detection type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PATTERNDETECTION? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PATTERNDETECTION? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PATTERNDETECTION value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PATTERNDETECTION {AUTO|MANUAL}
- MEASUrement:MEAS<x>:PATTERNDETECTION?

Info

MEAS<x> specifies the measurement number.
AUTO automatically detects the pattern.
MANUAL requires manually detecting the pattern.

patternlength `property` ¶

patternlength: MeasurementMeasItemPatternlength

Return the MEASUrement:MEAS<x>:PATTERNLENgth command.

Description

This command sets or queries the pattern length for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PATTERNLENgth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PATTERNLENgth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PATTERNLENgth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PATTERNLENgth <NR3>
- MEASUrement:MEAS<x>:PATTERNLENgth?

Info

MEAS<x> specifies the measurement number.
<NR3> is the pattern length.

patterntype `property` ¶

patterntype: MeasurementMeasItemPatterntype

Return the MEASUrement:MEAS<x>:PATTERNTYPe command.

Description

This command sets or queries the pattern type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PATTERNTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PATTERNTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PATTERNTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PATTERNTYPe {REPeating|ARBitrary}
- MEASUrement:MEAS<x>:PATTERNTYPe?

Info

MEAS<x> specifies the measurement number.
REPeating specifies a repeating pattern.
ARBitrary specifies an arbitrary pattern.

pcount `property` ¶

pcount: MeasurementMeasItemPcount

Return the MEASUrement:MEAS<x>:PCOUNt command.

Description

This command sets or returns number of pulses. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PCOUNt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PCOUNt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PCOUNt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PCOUNt <NR3>
- MEASUrement:MEAS<x>:PCOUNt?

Info

MEAS<x> specifies the measurement number.
<NR3> is the number of pulses.

perfreq `property` ¶

perfreq: MeasurementMeasItemPerfreq

Return the MEASUrement:MEAS<x>:PERFREQ command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.edge: The MEASUrement:MEAS<x>:PERFREQ:EDGE command.

pfrequency `property` ¶

pfrequency: MeasurementMeasItemPfrequency

Return the MEASUrement:MEAS<x>:PFREquency command.

Description

This command sets or returns the PJ max frequency value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PFREquency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PFREquency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PFREquency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PFREquency <NR3>
- MEASUrement:MEAS<x>:PFREquency?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of PJ max frequency for PSIJ measurement.

polarity `property` ¶

polarity: MeasurementMeasItemPolarity

Return the MEASUrement:MEAS<x>:POLarity command.

Description

This command sets or queries the polarity for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POLarity? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POLarity value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?

Info

MEAS<x> specifies the measurement number.
NORMal specifies normal polarity.
INVerted specifies inverted polarity.

popower `property` ¶

popower: MeasurementMeasItemPopower

Return the MEASUrement:MEAS<x>:POPower command.

Description

This command sets or queries the Percentage Power to be measured for the Occupied Bandwidth measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPower? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPower? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPower value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPower <NR3>
- MEASUrement:MEAS<x>:POPower?

Info

<NR3> sets the Percentage Power value. The default value is 99.9 and the valid range is 60.0 to 99.9.

population `property` ¶

population: MeasurementMeasItemPopulation

Return the MEASUrement:MEAS<x>:POPUlation command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.global: The MEASUrement:MEAS<x>:POPUlation:GLOBal command.
.limit: The MEASUrement:MEAS<x>:POPUlation:LIMIT command tree.

powerfactor `property` ¶

powerfactor: MeasurementMeasItemPowerfactor

Return the MEASUrement:MEAS<x>:POWERFACtor command.

Description

This command sets or queries the power factor value for IEC-Class C type harmonics standard. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POWERFACtor? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POWERFACtor? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POWERFACtor value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POWERFACtor <NR2>
- MEASUrement:MEAS<x>:POWERFACtor?

Info

MEAS<x> specifies the measurement number.
<NR2> specifies the power factor value for class C harmonics standard.

pregion `property` ¶

pregion: MeasurementMeasItemPregion

Return the MEASUrement:MEAS<x>:PREGion command.

Description

This command sets or returns pulse region for a measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PREGion? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PREGion? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PREGion value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PREGion {FPULse|SPULse|MPULse}
- MEASUrement:MEAS<x>:PREGion?

Info

FPULse is the pulse region as Fpulse.
SPULse is the pulse region as Spulse.
MPULse is the pulse region as Mpulse.

presistance `property` ¶

presistance: MeasurementMeasItemPresistance

Return the MEASUrement:MEAS<x>:PRESistance command.

Description

This command sets or returns the probe resistance for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PRESistance? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PRESistance? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PRESistance value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PRESistance <NR3>
- MEASUrement:MEAS<x>:PRESistance?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for probe resistance of the WBG measurement.

pthreshold `property` ¶

pthreshold: MeasurementMeasItemPthreshold

Return the MEASUrement:MEAS<x>:PTHReshold command.

Description

This command sets or returns the PJ threshold value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PTHReshold? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PTHReshold? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PTHReshold value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PTHReshold <NR3>
- MEASUrement:MEAS<x>:PTHReshold?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of PJ threshold for PSIJ measurement.

pwidth `property` ¶

pwidth: MeasurementMeasItemPwidth

Return the MEASUrement:MEAS<x>:PWIDth command.

Description

This command sets or returns pulse width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PWIDth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PWIDth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PWIDth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PWIDth <NR3>
- MEASUrement:MEAS<x>:PWIDth?

Info

<NR3> specifies the pulse width.

redge `property` ¶

redge: MeasurementMeasItemRedge

Return the MEASUrement:MEAS<x>:REDGe command.

Description

This command turns on or off the Refine edge on qualifier. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REDGe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REDGe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REDGe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REDGe {ON|OFF}
- MEASUrement:MEAS<x>:REDGe?

Info

ON specifies the Refine edge settings has been turned on.
OFF specifies the Refine edge settings has been turned off.

reflevels `property` ¶

reflevels: MeasurementMeasItemReflevels

Return the MEASUrement:MEAS<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.absolute: The MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

reflevels1 `property` ¶

reflevels1: MeasurementMeasItemReflevels1

Return the MEASUrement:MEAS<x>:REFLevels1 command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.absolute: The MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.
.basetop: The MEASUrement:MEAS<x>:REFLevels1:BASETop command.
.method: The MEASUrement:MEAS<x>:REFLevels1:METHod command.
.percent: The MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

refmode `property` ¶

refmode: MeasurementMeasItemRefmode

Return the MEASUrement:MEAS<x>:REFMode command.

Description

This command sets or queries the reference level mode for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFMode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?

Info

MEAS<x> specifies the measurement number.
AUTO sets the reference level for the measurement automatically.
MANual allows the user to set the reference level for the measurement.

refvoltage `property` ¶

refvoltage: MeasurementMeasItemRefvoltage

Return the MEASUrement:MEAS<x>:REFVoltage command.

Description

This command sets or queries the reference voltage value for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?

Info

MEAS<x> is the measurement number.
<NR3> is the reference voltage value for the selected configuration.

refvoltageval `property` ¶

refvoltageval: dict[int, MeasurementMeasItemRefvoltagevalItem]

Return the MEASUrement:MEAS<x>:REFVOLTAGE<x>Val command.

Description

Sets or queries the reference voltage per rail of Overshoot and Undershoot measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFVOLTAGE<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFVOLTAGE<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFVOLTAGE<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFVOLTAGE<x>Val <NR2>
- MEASUrement:MEAS<x>:REFVOLTAGE<x>Val?

Info

MEAS<x> is the measurement number.
REFVOLTAGE<x> is the rail number.
<NR2> is the reference voltage, in the range of -500 V to +500 V.

results `property` ¶

results: MeasurementMeasItemResults

Return the MEASUrement:MEAS<x>:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.allacqs: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.
.history: The MEASUrement:MEAS<x>:RESUlts:HISTory command tree.

rfrequency `property` ¶

rfrequency: MeasurementMeasItemRfrequency

Return the MEASUrement:MEAS<x>:RFREquency command.

Description

This command sets or returns the center frequency value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RFREquency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RFREquency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:RFREquency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:RFREquency <NR3>
- MEASUrement:MEAS<x>:RFREquency?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of center frequency for PSIJ measurement.

ripplefreqval `property` ¶

ripplefreqval: dict[int, MeasurementMeasItemRipplefreqvalItem]

Return the MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val command.

Description

Sets or queries the ripple frequency per specified rail for Ripple measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val <NR3>
- MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val?

Info

MEAS<x> is the measurement number.
RIPPLEFREQ<x> is the rail number.
<NR3> is the frequency, in the range of 1 Hz to 4 GHz.

rrange `property` ¶

rrange: MeasurementMeasItemRrange

Return the MEASUrement:MEAS<x>:RRANGE command.

Description

This command sets or returns the span value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RRANGE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RRANGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:RRANGE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:RRANGE <NR3>
- MEASUrement:MEAS<x>:RRANGE?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of span for PSIJ measurement.

sequence `property` ¶

sequence: MeasurementMeasItemSequence

Return the MEASUrement:MEAS<x>:SEQuence command.

Description

This command sets or queries the sequence of hall edges. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SEQuence? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SEQuence? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SEQuence value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SEQuence {ABC|ACB}
- MEASUrement:MEAS<x>:SEQuence?

Info

MEAS<x> specifies the measurement number.
ABC specifies the motor Hall edges sequence as ABC.
ACB specifies the motor Hall edges sequence as ACB.

signalfrequency `property` ¶

signalfrequency: MeasurementMeasItemSignalfrequency

Return the MEASUrement:MEAS<x>:SIGNALFREQUEncy command.

Description

This command sets or queries line frequency for Harmonics and Ripple line frequency. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SIGNALFREQUEncy? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SIGNALFREQUEncy? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SIGNALFREQUEncy value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SIGNALFREQUEncy {AUTO|FIFTYHZ|SIXTYHZ|FOURHUNDREDHZ|CUSTOM}
- MEASUrement:MEAS<x>:SIGNALFREQUEncy?

Info

MEAS<x> specifies the measurement number.
AUTO specifies the line frequency as auto. Only available for Harmonics line frequency.
FIFTYHZ specifies the line frequency as 50 Hz.
SIXTYHZ specifies the line frequency as 60 Hz.
FOURHUNDREDHZ specifies the line frequency as 400 Hz.
CUSTOM specifies the line frequency as custom.

signaltype `property` ¶

signaltype: MeasurementMeasItemSignaltype

Return the MEASUrement:MEAS<x>:SIGNALType command.

Description

This command sets or queries the signal type of source 1 for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SIGNALType? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SIGNALType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SIGNALType value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?

Info

MEAS<x> specifies the measurement number.
CLOCK specifies a clock signal type.
DATA specifies a data signal type.
AUTO automatically selects the signal type.

slabs `property` ¶

slabs: MeasurementMeasItemSlabs

Return the MEASUrement:MEAS<x>:SLABs command.

Description

This command sets or returns the value for the start level in absolute.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SLABs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SLABs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SLABs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SLABs <NR3>
- MEASUrement:MEAS<x>:SLABs?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the start level in absolute.

slpct `property` ¶

slpct: MeasurementMeasItemSlpct

Return the MEASUrement:MEAS<x>:SLPCt command.

Description

This command sets or returns the value for the start level in percentage.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SLPCt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SLPCt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SLPCt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SLPCt <NR3>
- MEASUrement:MEAS<x>:SLPCt?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the start level in percentage.

sltype `property` ¶

sltype: MeasurementMeasItemSltype

Return the MEASUrement:MEAS<x>:SLTYpe command.

Description

This command sets or returns the start level source type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SLTYpe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SLTYpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SLTYpe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:SLTYpe?

Info

MEAS<x> specifies the measurement number.
VDS specifies the start level source type as VDS.
ID specifies the start level source type as ID.
VGE specifies the start level source type as VGE.
VCE specifies the start level source type as VCE.
IC specifies the start level source type as IC.

smoothingfilter `property` ¶

smoothingfilter: MeasurementMeasItemSmoothingfilter

Return the MEASUrement:MEAS<x>:SMOOTHINGFILTER command.

Description

This command sets or queries the status of smoothing filter.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:SMOOTHINGFILTER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SMOOTHINGFILTER <NR1>

Info

MEAS<x> specifies the measurement number.
<NR1> sets the value to 1 or 0. 1 enables smoothing filter and 0 disables it.

source `property` ¶

source: MeasurementMeasItemSource

Return the MEASUrement:MEAS<x>:SOURCE command.

Description

This command sets or queries local input source.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:SOURCE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SOURCE {CH<x>|MATH<x>|REF<x>}

Info

MEAS<x> specifies the measurement number.
CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

source1 `property` ¶

source1: MeasurementMeasItemSource1

Return the MEASUrement:MEAS<x>:SOUrce1 command.

Description

This command sets or queries the measurement source. The measurement number and source are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SOUrce1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write() method will send the MEASUrement:MEAS<x>:SOUrce1 command.

SCPI Syntax

- MEASUrement:MEAS<x>:SOUrce1
- MEASUrement:MEAS<x>:SOUrce1?

Info

MEAS<x> specifies the measurement number.
1 specifies the source number.

spanval `property` ¶

spanval: dict[int, MeasurementMeasItemSpanvalItem]

Return the MEASUrement:MEAS<x>:SPAN<x>Val command.

Description

This command sets or returns the span value for PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SPAN<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SPAN<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SPAN<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SPAN<x>Val <NR3>
- MEASUrement:MEAS<x>:SPAN<x>Val?

Info

MEAS<x> specifies the measurement number.
SPAN<x> specifies the span number.
<NR3> specifies the span value.

srate `property` ¶

srate: MeasurementMeasItemSrate

Return the MEASUrement:MEAS<x>:SRATe command.

Description

This command sets or queries the symbol rate for the RRC filter in the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SRATe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SRATe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SRATe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SRATe <NR3>
- MEASUrement:MEAS<x>:SRATe?

Info

<NR3> sets the symbol rate. The default is 3.84e6 and the valid range is 1.0 to 5.0e9.

srho `property` ¶

srho: MeasurementMeasItemSrho

Return the MEASUrement:MEAS<x>:SRHo command.

Description

This command enables or disables the rho waveform for TDR measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SRHo? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SRHo? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SRHo value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SRHo {ON|OFF}
- MEASUrement:MEAS<x>:SRHo?

Info

ON specifies that rho waveform is enabled for TDR measurement.
OFF specifies that rho waveform is disabled for TDR measurement.

ssc `property` ¶

ssc: MeasurementMeasItemSsc

Return the MEASUrement:MEAS<x>:SSC command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSC? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.nominalfreq: The MEASUrement:MEAS<x>:SSC:NOMinalfreq command.

ssdirection `property` ¶

ssdirection: MeasurementMeasItemSsdirection

Return the MEASUrement:MEAS<x>:SSDirection command.

Description

This command sets or returns the start search direction for measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSDirection? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSDirection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SSDirection value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SSDirection {FORWARD|BACKWARD}
- MEASUrement:MEAS<x>:SSDirection?

Info

FORWARD specifies the start search direction for measurement as forward.
BACKWARD specifies the start search direction for measurement as backward.

status `property` ¶

status: MeasurementMeasItemStatus

Return the MEASUrement:MEAS<x>:STATUS command.

Description

This command returns the pass fail status, if applicable, for the selected measurement. Measur are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STATUS? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STATUS? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:STATUS?

Info

PASS specifies that the user specified measurement limit has not been violated.
FAIL specifies that the user specified measurement limit has been violated.

stlabs `property` ¶

stlabs: MeasurementMeasItemStlabs

Return the MEASUrement:MEAS<x>:STLABs command.

Description

This command sets or returns the value for the stop level in absolute.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STLABs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STLABs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STLABs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STLABs <NR3>
- MEASUrement:MEAS<x>:STLABs?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the stop level in absolute.

stlpct `property` ¶

stlpct: MeasurementMeasItemStlpct

Return the MEASUrement:MEAS<x>:STLPct command.

Description

This command sets or returns the value for the stop level in percentage.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STLPct? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STLPct? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STLPct value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STLPct <NR3>
- MEASUrement:MEAS<x>:STLPct?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the stop level in percentage.

stltype `property` ¶

stltype: MeasurementMeasItemStltype

Return the MEASUrement:MEAS<x>:STLTYpe command.

Description

This command sets or returns the stop level source type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STLTYpe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STLTYpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STLTYpe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:STLTYpe?

Info

MEAS<x> specifies the measurement number.
VDS specifies the stop level source type as VDS.
ID specifies the stop level source type as ID.
VGE specifies the stop level source type as VGE.
VCE specifies the stop level source type as VCE.
IC specifies the stop level source type as IC.

stsdirection `property` ¶

stsdirection: MeasurementMeasItemStsdirection

Return the MEASUrement:MEAS<x>:STSDirection command.

Description

This command sets or returns the stop search direction for measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STSDirection? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STSDirection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STSDirection value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STSDirection {FORWARD|BACKWARD}
- MEASUrement:MEAS<x>:STSDirection?

Info

FORWARD specifies the stop search direction for measurement as forward.
BACKWARD specifies the stop search direction for measurement as backward.

stype `property` ¶

stype: MeasurementMeasItemStype

Return the MEASUrement:MEAS<x>:STYPe command.

Description

This command sets or queries the source type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STYPe {VOLTage|CURRent|DIFFERENTIAL|SINGLE}
- MEASUrement:MEAS<x>:STYPe?

Info

MEAS<x> specifies the measurement number.
VOLTage sets source type as Voltage.
CURRent sets source type as Current.
DIFFERENTIAL sets source type as Differential.
SINGLE sets source type as Single.

subgroup `property` ¶

subgroup: MeasurementMeasItemSubgroup

Return the MEASUrement:MEAS<x>:SUBGROUP command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.results: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts command tree.

sunits `property` ¶

sunits: MeasurementMeasItemSunits

Return the MEASUrement:MEAS<x>:SUNits command.

Description

This command sets or queries the speed units for the specific measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUNits? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SUNits value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SUNits {RPM|HZ}
- MEASUrement:MEAS<x>:SUNits?

Info

MEAS<x> specifies the measurement number.
RPM defines the speed measurement units as RPM.
HZ defines the speed measurement units as HZ.

tckavg `property` ¶

tckavg: MeasurementMeasItemTckavg

Return the MEASUrement:MEAS<x>:TCKAVG command.

Description

This command sets or queries the average clock period value used in DDR measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TCKAVG? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TCKAVG? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TCKAVG value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TCKAVG <NR3>
- MEASUrement:MEAS<x>:TCKAVG?

Info

MEAS<x> specifies the measurement number.
<NR3> is a floating point number that represents the DDR average clock period in seconds.

tconstant `property` ¶

tconstant: MeasurementMeasItemTconstant

Return the MEASUrement:MEAS<x>:TCONstant command.

Description

This command sets or queries the measurement Torque Constant.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TCONstant? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TCONstant? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TCONstant value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TCONstant <NR1>
- MEASUrement:MEAS<x>:TCONstant?

Info

MEAS<x> specifies the measurement number.
NR1 specifies the current multiplier value of the measurement in the range of 0 to 100.

tdrpreset `property` ¶

tdrpreset: MeasurementMeasItemTdrpreset

Return the MEASUrement:MEAS<x>:TDRPreset command.

Description

This command executes the preset for TDR measurement.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:TDRPreset value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TDRPreset {EXECUTE}

Info

MEAS<x> specifies the measurement number.
EXECUTE executes the preset for TDR measurement.

timingmode `property` ¶

timingmode: MeasurementMeasItemTimingmode

Return the MEASUrement:MEAS<x>:TIMINGMode command.

Description

This command sets or queries the Timing mode for the specified DDR measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TIMINGMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TIMINGMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TIMINGMode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TIMINGMode {EACHCLOCKCYCLE|TWOCLOCKCYCLES}
- MEASUrement:MEAS<x>:TIMINGMode?

Info

MEAS<x> specifies the measurement number.
EACHCLOCKCYCLE sets the DDR Timing Mode to use each clock cycle at a time.
TWOCLOCKCYCLES sets the DDR Timing Mode to use two cycles at a time.

tlevel `property` ¶

tlevel: MeasurementMeasItemTlevel

Return the MEASUrement:MEAS<x>:TLEVel command.

Description

This command sets or queries whether histogram center is percentage relative to unit amplitude or an absolute value, for eye height measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TLEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TLEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TLEVel {PERCent|ABSolute}
- MEASUrement:MEAS<x>:TLEVel?

Info

MEAS<x> specifies the measurement number.
PERCent sets the histogram center as a percentage relative to unit amplitude.
ABSolute sets the histogram center as an absolute value.

tmethod `property` ¶

tmethod: MeasurementMeasItemTmethod

Return the MEASUrement:MEAS<x>:TMEThod command.

Description

This command sets or queries the measurement torque method.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TMEThod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TMEThod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TMEThod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TMEThod {SENSOR|CURRENT}
- MEASUrement:MEAS<x>:TMEThod?

Info

MEAS<x> specifies the measurement number.
SENSOR specifies the Torque Method as SENSOR.
CURRENT specifies the Torque Method as CURRENT.

toedge `property` ¶

toedge: MeasurementMeasItemToedge

Return the MEASUrement:MEAS<x>:TOEdge command.

Description

This command sets or queries the ‘to edge’ type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEdge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEdge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEdge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISe specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

toedgesearchdirect `property` ¶

toedgesearchdirect: MeasurementMeasItemToedgesearchdirect

Return the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.

Description

This command sets or queries the to edge search direction for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search to the edge.
BACKWard specifies a backward search to the edge.

tosymbol `property` ¶

tosymbol: MeasurementMeasItemTosymbol

Return the MEASUrement:MEAS<x>:TOSYmbol command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.logic2source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce command.
.logic3source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce command.
.logic4source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce command.
.logic5source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce command.
.measureat: The MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT command.

transition `property` ¶

transition: MeasurementMeasItemTransition

Return the MEASUrement:MEAS<x>:TRANSition command.

Description

This command sets or queries the transition edges flag for the measurement. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:TRANSition value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}

Info

<NR1> = 1, the measurement is computed on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only. If it is set to 0, the measurement is computed on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
OFF computes the measurement on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
ON computes the measurement on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only.

type `property` ¶

type: MeasurementMeasItemType

Return the MEASUrement:MEAS<x>:TYPe command.

Description

This command sets or queries the measurement type for the measurement specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TYPe {ACCOMMONMODE|ACPR|ACRMS|AMPLITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|CPOWER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMOVERSHOOT|DPMPSIJ|DPMUNDERSHOOT|DPMRIPPLE|DPMTURNOFFTIME|DPMTURNONTIME|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HIGH|HEIGHT|HEIGHTBER|HIGHTIME|HOLD|IMDAANGLE|IMDADIRECTION|IMDADQ0|IMDAEFFICIENCY|IMDAHARMONICS|IMDAMECHPWR|IMDAPOWERQUALITY|IMDASPEED|IMDASYSEFF|IMDATORQUE|ISI|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NPJ|NOVERSHOOT|NWIDTH|OBW|PATTERNLENGTH|PDUTTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RDSON|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SRJ|SSCFREQDEV|SSCMODRATE|SSCSLEWRATE|SETUP|SKEW|TDR|TIE|TIMEOUTSIDELEVEL|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WBGDDT|WBGDIODEDDT|WBGEOFF|WBGEON|WBGERR|WBGIPEAK|WBGIRRM|WBGQOSS|WBGQRR|WBGTDOFF|WBGTDON|WBGTF|WBGTON|WBGTOFF|WBGTR|WBGTRR|WBGTDT|WBGVPEAK|WIDTH|WIDTHBER}
- MEASUrement:MEAS<x>:TYPe?

Info

ACCOMMONMODE AC Common Mode (Pk-Pk) is the peak-to-peak of the commonmode voltage of two sources. This measurement is made across the entire record.This measurement requires the DJA option and is not available on a 4 SeriesMSO instrument.
ACPR (Adjacent Channel Power Ratio) is the amount of power that leaks intoadjacent channels. This can be specified in terms of absolute power or a ratio ofadjacent channel power to the main channel power, called adjacent channel powerratio (ACPR) or adjacent channel leakage ratio (ACLR).
ACRMS (AC RMS) is the true Root Mean Square of the data points, about theMean. This measurement can be made across the entire record, or on each cyclein the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BITAMPLITUDE (Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITHIGH (Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITLOW (Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
CCJITTER (Cycle-to-Cycle jitter) measures how much the clock period changes between any two adjacent cycles. Cycle-to-Cycle jitter is measured by applying a first order difference operation to the period jitter.
COMMONMODE (DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
CPOWER (Channel Power) is the measurement of integrated power within a specified channel bandwidth for a RF signal. The resulting channel power is an absolute power measurement.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DCD (duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDJ (data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDRAOS (area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.
DDRAOSPERTCK (area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAOSPERUI (area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRAUS (area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.
DDRAUSPERTCK (area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAUSPERUI (area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRHOLDDIFF (hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.
DDRSETUPDIFF (setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.
DDRTCHABS (absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.
DDRTCHAVERAGE (average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCKAVERAGE (average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCLABS (absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.
DDRTCLAVERAGE (average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.
DDRTERRMN (cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).
DDRTERRN (cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).
DDRTJITCC (cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.
DDRTJITDUTY (half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.
DDRTJITPER (clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.
DDRTPST (read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.
DDRTRPRE (read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRTWPRE is the width of theWrite burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRVIXAC is the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.
DDRTDQSCK is the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
DJ (deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DJDIRAC (dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DPMPSIJ is the Power Supply Induced Jitter. This measurement helps in suppressing the jitter in high speed signals (victim) induced from power rail signals (aggressor).
EYEHIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
EYELOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
F2 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F4 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F8 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.
HEIGHT (Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HEIGHTBER (Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
IMDAANGLE (Angle) measures the phase angle. Configure QEI or Hall sensor to.
compute the angle measurement. Requires a IMDA-MECH License.
IMDADIRECTION (Direction) defines the direction of rotation of the motor. Set the direction A-B-C or A-C-B for Hall sensors and CW or CCW for QEI based on the motor configuration. Requires a IMDA-MECH License.
IMDADQ0 measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0. Requires a IMDA-MECH License.
IMDAEFFICIENCY (Efficiency) measures the ratio of sum of output power(s) to input power for respective input and output Voltage and Current pairs. Note: the current release cannot support 3V and 3I pairs, since this requires 12 channels. We restrict to 2V and 2I which needs 8 scope channels. Requires a IMDA-MECH License.
IMDAHARMONICS (Harmonics) plots the signal amplitude at the fundamental line frequency and its harmonics and measures the RMS amplitude and Total Harmonic Distortion of the signal. Requires a IMDA-MECH License.
IMDAMECHPWR (Mechanical Power) measures the mechanical power of the motor drive system. It is determined by the Speed and Torque. It is measured in watts. Requires a IMDA-MECH License.
IMDAPOWERQUALITY (Power Quality) measures the Frequency and RMS values of the voltage and current, Crest Factors of the voltage and current, True Power (PTRUE), Reactive Power (PRE), Apparent Power (PAPP), Power Factor, and Phase Angle (θ) of the AC signal. Requires a IMDA-MECH License.
IMDASPEED (Speed) measures the speed and acceleration. Requires a IMDA-MECH License.
IMDASYSEFF (System Efficiency) measures the total efficiency of the motor drive system. Requires a IMDA-MECH License.
IMDATORQUE (Torque) measures the torque of the motor. Configure Sensor (analog) or Current method to measure the torque. Requires a IMDA-MECH License.
ISI (Inter Symbol Interference) is defined as the range (difference between the maximum and minimum value) of DDJ-per-edge values appearing across all rising edges, or the range of DDJ-per-edge values across all falling edges, whichever is greater. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
JITTERSUMMARY (Jitter Summary) is a group consisting of the followingmeasurements: Data Rate, Pattern Length, TIE, TJ@BER, RJ, DJ, DJ-δδ, PJ,DDJ, DCD, Eye Width@BER and RJ-δδ. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
JITTERSUMMARY (Jitter Summary) is a group consisting of the following measurements: TIE, TJ@BER, Eye Width@BER, Eye Height@BER, RJ-δδ, DJ-δδ, PJ, DDJ, DcD, F/2, F/4, F/8. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
J2 is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
J9 is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
LOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NPJ (non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIDTH (Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.
OBW (Occupied Bandwidth) refers to the bandwidth, including energy of a certain proportion of the total transmitted power, with the center frequency of the specified channel as the center.
PATTERNLENGTH (Pattern Length) is the number of symbols that constitute onefull repetition of a sequence within a signal. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PHASENOISE (Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.
PJ (periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
QFACTOR (Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RDSON (Dynamic resistance) is the resistance offered by a switching device whendevice is in ON condition. RDS(on) measurement will provide trend of dynamicresistance on auto created math waveform.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RJ (random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RJDIRAC (dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SRJ (sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCFREQDEV (SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCMODRATE (SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCSLEWRATE (SSC Slew Rate) is the rate of change of the modulating frequencyof a spread spectrum clock. This measurement is made on each cycle in therecord. This measurement requires the DJA option and is not available on a 4Series MSO instrument.
SETUP (Setup Time) is the time between the specified Mid reference level (R.
SKEW Skew is the time between the specified Mid reference level (R.
TIE (time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (R.
TIMETOMAX Time to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.
TIMETOMIN Time to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.
TJBER (total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TNTRATIO T/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
UNITINTERVAL (Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.
VDIFFXOVR (Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WBGDDT (d/dt) measures the rate of change of voltage or current (slew rate) from the configured start level to the stop level. Requires a WBG-DPT License.
WBGDIODEDDT (Diode d/dt) measures the rate of change of voltage or current (slew rate) during the specified start and stop integration levels. Diode d/dt can be measured during rising or falling edge. Requires a WBG-DPT License.
WBGEOFF (Eoff) measures the energy dissipated in the Power Device during off region using the configured levels. Requires a WBG-DPT License.
WBGEON (Eon) measures the energy dissipated in the Power Device during on region using the configured levels. Requires a WBG-DPT License.
WBGERR (Err) measures the reverse recovery energy dissipated in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGIPEAK (Ipeak) measures the peak current of the Power Device in the on region. Requires a WBG-DPT License.
WBGIRRM (Irrm) measures the maximum current dissipated in the Power Device in the reverse recovery region. Requires a WBG-DPT License.
WBGQOSS (Qoss) is the charge that must be supplied to the output capacitance of the power device during a specified time interval. Requires a WBG-DPT License.
WBGQRR (Qrr) measures the reverse recovery charge in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDOFF (Td(off)) measures the turn off delay time of the Power Device in the off region using the configured levels. Requires a WBG-DPT License.
WBGTDON (Td(on)) measures the turn on delay time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTF (Tf) measures the fall time of the Power Device in the off region using the configured levels.
WBGTOFF (Toff) measures the turn off time of the Power Device. It is the sum of the turn off delay time and the fall time. Requires a WBG-DPT License.
WBGTON (Ton) measures the turn on time of the Power Device. It is the sum of the turn on delay time and the rise time. Requires a WBG-DPT License.
WBGTR (Tr) measures the rise time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTRR (Trr) measures the reverse recovery time of the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDT (Tdt) the time delay between turn on time of the high side MOSFET and turn on time of the low side MOSFET during the simultaneous switching. Requires a WBG-DPT License.
WBGVPEAK (Vpeak) measures the peak voltage of the Power Device in the off region. Requires a WBG-DPT License.
WIDTH (Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WIDTHBER (Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.

vlevel `property` ¶

vlevel: MeasurementMeasItemVlevel

Return the MEASUrement:MEAS<x>:VLEVel command.

Description

This command sets or queries whether histogram center is percentage relative to unit interval or an absolute value for eye width measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:VLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:VLEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:VLEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:VLEVel {PERCent|ABSolute}
- MEASUrement:MEAS<x>:VLEVel?

Info

MEAS<x> is the measurement number.
PERCent sets the histogram center as a percentage relative to unit interval.
ABSolute sets the histogram center as an absolute value.

waittime `property` ¶

waittime: MeasurementMeasItemWaittime

Return the MEASUrement:MEAS<x>:WAITTime command.

Description

Sets or queries the wait time.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WAITTime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WAITTime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WAITTime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WAITTime <NR2>
- MEASUrement:MEAS<x>:WAITTime?

Info

MEAS<x> is the measurement number.
<NR2> is the wait time, in the range of 1 s to 500 s.

wbg `property` ¶

wbg: MeasurementMeasItemWbg

Return the MEASUrement:MEAS<x>:WBG command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.afgsetup: The MEASUrement:MEAS<x>:WBG:AFGSetup command.
.afgaddress: The MEASUrement:MEAS<x>:WBG:AFGaddress command.
.cstatus: The MEASUrement:MEAS<x>:WBG:CSTatus command.
.gtype: The MEASUrement:MEAS<x>:WBG:GTYPe command.
.high: The MEASUrement:MEAS<x>:WBG:HIGH command.
.load: The MEASUrement:MEAS<x>:WBG:LOAD command.
.low: The MEASUrement:MEAS<x>:WBG:LOW command.
.npuls: The MEASUrement:MEAS<x>:WBG:NPULs command.
.pgval: The MEASUrement:MEAS<x>:WBG:PG<x>Val command.
.pwval: The MEASUrement:MEAS<x>:WBG:PW<x>Val command.
.timer: The MEASUrement:MEAS<x>:WBG:TIMer command.

width `property` ¶

width: MeasurementMeasItemWidth

Return the MEASUrement:MEAS<x>:WIDTh command.

Description

This command sets or queries the histogram width in terms of percentage.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WIDTh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WIDTh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WIDTh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WIDTh <NR1>
- MEASUrement:MEAS<x>:WIDTh?

Info

MEAS<x> specifies the measurement number.
<NR1> is the value for the width.

windowlength `property` ¶

windowlength: MeasurementMeasItemWindowlength

Return the MEASUrement:MEAS<x>:WINDOWLENgth command.

Description

This command sets or queries the window length for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WINDOWLENgth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WINDOWLENgth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WINDOWLENgth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WINDOWLENgth <NR3>
- MEASUrement:MEAS<x>:WINDOWLENgth?

Info

<NR3> is the value for the window length.

xunit `property` ¶

xunit: MeasurementMeasItemXunit

Return the MEASUrement:MEAS<x>:XUNIT command.

Description

Returns the horizontal scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:XUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:XUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:XUNIT?

Info

MEAS<x> specifies the measurement number.

yunit `property` ¶

yunit: MeasurementMeasItemYunit

Return the MEASUrement:MEAS<x>:YUNIT command.

Description

Returns the vertical scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:YUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:YUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:YUNIT?

Info

MEAS<x> specifies the measurement number.

MeasurementMeasItemAbandwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:ABANdwidth command.

Description

This command sets or queries the analysis bandwidth for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:ABANdwidth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:ABANdwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:ABANdwidth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:ABANdwidth <NR3>
- MEASUrement:MEAS<x>:ABANdwidth?

Info

MEAS<x> specifies the measurement number.
<NR3> sets the analysis bandwidth. The default value is 10.0e6 and the valid range is 1.0e3 to 8.0e9.

MeasurementMeasItemAchannels ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:ACHANnels command.

Description

This command sets or queries the number of adjacent channels for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:ACHANnels? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:ACHANnels? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:ACHANnels value command.

SCPI Syntax

- MEASUrement:MEAS<x>:ACHANnels <NR3>
- MEASUrement:MEAS<x>:ACHANnels?

Info

MEAS<x> specifies the measurement number.
<NR3> sets the number of adjacent channels. The default value is 1 and the valid range is 1 to 5.

MeasurementMeasItemAmethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:AMEThod command.

Description

This command sets or queries the analysis method used to compute eye width or eye height.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:AMEThod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:AMEThod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:AMEThod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:AMEThod {PARAmetric|HISTogram}
- MEASUrement:MEAS<x>:AMEThod?

Info

MEAS<x> specifies the measurement number.
PARAmetric sets the analysis method to parametric.
HISTogram sets the analysis method to histogram.

MeasurementMeasItemBcount ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BCOunt command.

Description

This command sets or returns the burst count for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BCOunt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BCOunt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BCOunt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BCOunt <NR3>
- MEASUrement:MEAS<x>:BCOunt?

Info

BCOunt specifies the burst count for WBG measurement.

MeasurementMeasItemBdelay ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BDELay command.

Description

This command sets or returns the burst delay for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BDELay? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BDELay? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BDELay value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BDELay <NR3>
- MEASUrement:MEAS<x>:BDELay?

Info

BDELay specifies the burst delay for WBG measurement. This can be set or queried when generator type is AFG31000.

MeasurementMeasItemBer ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BER command.

Description

This command sets or queries BER value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BER <NR3>
- MEASUrement:MEAS<x>:BER?

Info

MEAS<x> specifies the measurement number.
<NR3> is BER value for the measurement.

Properties

.targetber: The MEASUrement:MEAS<x>:BER:TARGETBER command.

targetber `property` ¶

targetber: MeasurementMeasItemBerTargetber

Return the MEASUrement:MEAS<x>:BER:TARGETBER command.

Description

This command sets or queries the target BER value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BER:TARGETBER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BER:TARGETBER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BER:TARGETBER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BER:TARGETBER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER?

Info

MEAS<x> specifies the measurement number.
<NR3> is the target BER value.

MeasurementMeasItemBerTargetber ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BER:TARGETBER command.

Description

This command sets or queries the target BER value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BER:TARGETBER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BER:TARGETBER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BER:TARGETBER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BER:TARGETBER <NR3>
- MEASUrement:MEAS<x>:BER:TARGETBER?

Info

MEAS<x> specifies the measurement number.
<NR3> is the target BER value.

MeasurementMeasItemBin ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BIN command.

Description

This command sets or queries the bin count for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BIN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BIN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BIN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BIN <NR3>
- MEASUrement:MEAS<x>:BIN?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bin count.

MeasurementMeasItemBitabsolute ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BITAbsolute command.

Description

This command sets or queries the bit center as an absolute value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITAbsolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITAbsolute? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITAbsolute value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITAbsolute <NR3>
- MEASUrement:MEAS<x>:BITAbsolute?

Info

MEAS<x> specifies the measurement number.
<NR3> is the value for the bit center.

MeasurementMeasItemBitcfgmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BITCfgmode command.

Description

This command sets or queries whether the measurement returns the mean or mode statistic result when the measurement type is bit amplitude/high/low. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITCfgmode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITCfgmode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITCfgmode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITCfgmode {MEAN|MODE}
- MEASUrement:MEAS<x>:BITCfgmode?

Info

MEAS<x> specifies the measurement number.
MEAN specifies that the measurement returns results for each bit.
MODE specifies that the measurement returns the mode of its results.

MeasurementMeasItemBitend ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BITEnd command.

Description

This command sets or queries the bit end as a percentage of the unit interval. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITEnd? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITEnd? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITEnd value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITEnd <NR3>
- MEASUrement:MEAS<x>:BITEnd?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bit end.

MeasurementMeasItemBitpcnt ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BITPcnt command.

Description

This command sets or queries the bit center as a percentage of the unit interval. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITPcnt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITPcnt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITPcnt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITPcnt <NR3>
- MEASUrement:MEAS<x>:BITPcnt?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bit center percentage value to be measured for the bit type selected.

MeasurementMeasItemBitstart ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BITSTart command.

Description

This command sets or queries the bit start as a percentage of the unit interval. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITSTart? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITSTart? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITSTart value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITSTart <NR3>
- MEASUrement:MEAS<x>:BITSTart?

Info

MEAS<x> specifies the measurement number.
<NR3> is the bit start.

MeasurementMeasItemBittype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BITType command.

Description

This command sets or queries the bit type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BITType? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BITType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BITType value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- MEASUrement:MEAS<x>:BITType?

Info

MEAS<x> specifies the measurement number.
ALLBits specifies that the measurement returns results for all bits.
TRANSition specifies that the measurement returns results for transitions bit only.
NONTRANsition specifies that the measurement returns results for non-transition bits only.

MeasurementMeasItemBmtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BMTYPe command.

Description

Sets or queries the base measurement type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BMTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BMTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BMTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BMTYPe {TIE|PERIOD|NUInterval}
- MEASUrement:MEAS<x>:BMTYPe?

Info

MEAS<x> specifies the measurement number.
TIE specifies the base measurement type as TIE.
PERIOD specifies the base measurement type as PERIOD.
NUInterval specifies the base measurement type as NUInterval.

MeasurementMeasItemBurstedgtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BURSTEDGTYPe command.

Description

This command sets or queries the burst edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BURSTEDGTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BURSTEDGTYPe {RISE|FALL}
- MEASUrement:MEAS<x>:BURSTEDGTYPe?

Info

MEAS<x> specifies the measurement number.
RISE specifies a burst with a rising edge.
FALL specifies a burst with a falling edge.

MeasurementMeasItemBvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:BVOLTage command.

Description

This command sets or returns the bias voltage for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:BVOLTage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:BVOLTage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:BVOLTage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:BVOLTage <NR3>
- MEASUrement:MEAS<x>:BVOLTage?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for bias voltage of the WBG measurement.

MeasurementMeasItemCcresults ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts? query and raise an AssertionError if the returned value does not match value.

Properties

.allacqs: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

allacqs `property` ¶

allacqs: MeasurementMeasItemCcresultsAllacqs

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

currentacq `property` ¶

currentacq: MeasurementMeasItemCcresultsCurrentacq

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

MeasurementMeasItemCcresultsAllacqs ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemCcresultsAllacqsMaximum

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemCcresultsAllacqsMean

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemCcresultsAllacqsMinimum

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemCcresultsAllacqsPk2pk

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?

population `property` ¶

population: MeasurementMeasItemCcresultsAllacqsPopulation

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population of all cycle-cycle statistics for the specified measurement for all acquisitions accumulated since statistics were last reset. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemCcresultsAllacqsStddev

Return the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?

MeasurementMeasItemCcresultsAllacqsMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MAXimum?

MeasurementMeasItemCcresultsAllacqsMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MEAN?

MeasurementMeasItemCcresultsAllacqsMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:MINimum?

MeasurementMeasItemCcresultsAllacqsPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:PK2PK?

MeasurementMeasItemCcresultsAllacqsPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population of all cycle-cycle statistics for the specified measurement for all acquisitions accumulated since statistics were last reset. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:POPUlation?

MeasurementMeasItemCcresultsAllacqsStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for all acquisitions. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:ALLAcqs:STDDev?

MeasurementMeasItemCcresultsCurrentacq ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemCcresultsCurrentacqMaximum

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemCcresultsCurrentacqMean

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemCcresultsCurrentacqMinimum

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemCcresultsCurrentacqPk2pk

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?

population `property` ¶

population: MeasurementMeasItemCcresultsCurrentacqPopulation

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population of the cycle-cycle statistics for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemCcresultsCurrentacqStddev

Return the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?

MeasurementMeasItemCcresultsCurrentacqMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MAXimum?

MeasurementMeasItemCcresultsCurrentacqMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MEAN?

MeasurementMeasItemCcresultsCurrentacqMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum cycle-cycle value for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:MINimum?

MeasurementMeasItemCcresultsCurrentacqPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak to peak cycle-cycle statistic for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:PK2PK?

MeasurementMeasItemCcresultsCurrentacqPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population of the cycle-cycle statistics for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:POPUlation?

MeasurementMeasItemCcresultsCurrentacqStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation cycle-cycle for the specified measurement for the current acquisition. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:CCRESUlts:CURRentacq:STDDev?

MeasurementMeasItemCfvalItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CF<x>Val command.

Description

This command sets or returns the filter count for PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CF<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CF<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CF<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CF<x>Val <NR3>
- MEASUrement:MEAS<x>:CF<x>Val?

Info

MEAS<x> specifies the measurement number.
CF<x> specifies the center frequency number.
<NR3> specifies the center frequency.

MeasurementMeasItemClockrecovery ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.advanced: The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced command tree.
.clockfrequency: The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.
.clockmultiplier: The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.
.constclockmode: The MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe command.
.damping: The MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing command.
.datapath: The MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath command.
.datarate: The MEASUrement:MEAS<x>:CLOCKRecovery:DATARate command.
.explicitclockmode: The MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe command.
.global: The MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal command.
.jtfbandwidth: The MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth command.
.loopbandwidth: The MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.
.meanautocalculate: The MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.
.method: The MEASUrement:MEAS<x>:CLOCKRecovery:METHod command.
.model: The MEASUrement:MEAS<x>:CLOCKRecovery:MODel command.
.nominaloffset: The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.
.standard: The MEASUrement:MEAS<x>:CLOCKRecovery:STAndard command.
.tdcompensation: The MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation command.

advanced `property` ¶

advanced: MeasurementMeasItemClockrecoveryAdvanced

Return the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.method: The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod command.

clockfrequency `property` ¶

clockfrequency: MeasurementMeasItemClockrecoveryClockfrequency

Return the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.

Description

This command sets or queries the clock frequency used when fixed constant clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock frequency.

clockmultiplier `property` ¶

clockmultiplier: MeasurementMeasItemClockrecoveryClockmultiplier

Return the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.

Description

This command sets or queries the clock multiplier used when explicit clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock multiplier.

constclockmode `property` ¶

constclockmode: MeasurementMeasItemClockrecoveryConstclockmode

Return the MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe command.

Description

This command sets or queries the constant clock mode used when constant clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}

Info

MEAS<x> specifies the measurement number.
MEAN specifies that clock recovery uses the mean of the clock signal as the clock frequency.
MEDian specifies that clock recovery uses the mode of the clock signal as the clock frequency.
FIXed specifies that clock recovery uses the value set by the user as the clock frequency.

damping `property` ¶

damping: MeasurementMeasItemClockrecoveryDamping

Return the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing command.

Description

This command sets or queries the damping value used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock recovery damping value.

datapath `property` ¶

datapath: MeasurementMeasItemClockrecoveryDatapath

Return the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath command.

Description

This command sets or queries the file containing the data pattern used when known data pattern clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath <QString>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?

Info

MEAS<x> specifies the measurement number.
<QString> is the file containing the data pattern to be used for known data pattern clock recovery.

datarate `property` ¶

datarate: MeasurementMeasItemClockrecoveryDatarate

Return the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate command.

Description

This command sets or queries the nominal data bit rate when nominal data rate clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate?

Info

MEAS<x> specifies the measurement number.
<NR3> is the value for the Nominal data rate.

explicitclockmode `property` ¶

explicitclockmode: MeasurementMeasItemClockrecoveryExplicitclockmode

Return the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe command.

Description

This command sets or queries the explicit clock mode used when explicit clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?

Info

MEAS<x> specifies the measurement number.
EDGE specifies the clock edge.
PLL specifies the phase locked loop.

global_ `property` ¶

global_: MeasurementMeasItemClockrecoveryGlobal

Return the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal command.

Description

This command sets or queries the clock recovery settings global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF clock recovery settings are changed independently for each individual measurement.
ON applies global clock recovery settings to all the measurements’ clock recovery settings.
0 clock recovery settings are changed independently for each individual measurement.
1 applies global clock recovery settings to all the measurements’ clock recovery settings.

jtfbandwidth `property` ¶

jtfbandwidth: MeasurementMeasItemClockrecoveryJtfbandwidth

Return the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth command.

Description

This command sets or queries the JTF bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock recovery JTF bandwidth.

loopbandwidth `property` ¶

loopbandwidth: MeasurementMeasItemClockrecoveryLoopbandwidth

Return the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.

Description

This command sets or queries the loop bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock recovery loop bandwidth.

meanautocalculate `property` ¶

meanautocalculate: MeasurementMeasItemClockrecoveryMeanautocalculate

Return the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.

Description

This command sets or queries how often the clock is calculated when constant clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?

Info

MEAS<x> specifies the measurement number.
FIRST calculates the clock on the first acquisition.
EVERY calculates the clock on every acquisition.

method `property` ¶

method: MeasurementMeasItemClockrecoveryMethod

Return the MEASUrement:MEAS<x>:CLOCKRecovery:METHod command.

Description

This command sets or queries the clock recovery method for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod?

Info

MEAS<x> specifies the measurement number.
PLL specifies a phase locked loop clock recovery method.
CONSTANTCLOCK specifies using a constant clock.
EXPLICITCLOCK specifies using an explicit clock.

model `property` ¶

model: MeasurementMeasItemClockrecoveryModel

Return the MEASUrement:MEAS<x>:CLOCKRecovery:MODel command.

Description

This command sets or queries the PLL clock recovery model used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MODel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MODel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MODel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:MODel TYPE<x>
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel?

Info

MEAS<x> specifies the measurement number.
TYPE<x> set the clock recovery model type. Valid values are 1 or 2.

nominaloffset `property` ¶

nominaloffset: MeasurementMeasItemClockrecoveryNominaloffset

Return the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.

Description

This command sets or queries the offset value used when explicit clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock offset.

Sub-properties

.selectiontype: The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

standard `property` ¶

standard: MeasurementMeasItemClockrecoveryStandard

Return the MEASUrement:MEAS<x>:CLOCKRecovery:STAndard command.

Description

This command sets or queries the communications standard when PLL clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:STAndard value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}

Info

MEAS<x> specifies the measurement number.
CUSTom sets the standard to custom.
ENET100 sets the standard to ENET100.
FW1394BS400B sets the standard to FW1394BS400B.
FW1394BS800B sets the standard to FW1394BS800B.
FW1394BS1600B sets the standard to FW1394BS1600B.
FBD1 sets the standard to FBD1.
FBD2 sets the standard to FBD2.
FBD3 sets the standard to FBD3.
FC133 sets the standard to FC133.
FC266 sets the standard to FC266.
FC531 sets the standard to FC531.
FC1063 sets the standard to FC1063.
FC2125 sets the standard to FC2125.
FC4250 sets the standard to FC4250.
FC8500 sets the standard to FC8500.
ENET1000 sets the standard to ENET1000.
IBA2500 sets the standard to IBA2500.
IBA_GEN2 sets the standard to IBA_GEN2.
OC1 sets the standard to OC1.
OC3 sets the standard to OC3.
OC12 sets the standard to OC12.
OC48 sets the standard to OC48.
PCIE_GEN1 sets the standard to PCIE_GEN1.
PCIE_GEN2 sets the standard to PCIE_GEN2.
PCIE_GEN3 sets the standard to PCIE_GEN3.
RIO125 sets the standard to RIO125.
RIO250 sets the standard to RIO250.
RIO3125 sets the standard to RIO3125.
SAS15_NOSSC sets the standard to SAS15_NOSSC.
SAS3_NOSSC sets the standard to SAS3_NOSSC.
SAS6_NOSSC sets the standard to SAS6_NOSSC.
SAS12_NOSSC sets the standard to SAS12_NOSSC.
SAS15_SSC sets the standard to SAS15_SSC.
SAS3_SSC sets the standard to SAS3_SSC.
SAS6_SSC sets the standard to SAS6_SSC.
SAS12_SSC sets the standard to SAS12_SSC.
SATA_GEN1 sets the standard to SATA_GEN1.
SATA_GEN2 sets the standard to SATA_GEN2.
SATA_GEN3 sets the standard to SATA_GEN3.
USB3 sets the standard to USB3.
XAUI sets the standard to XAUI.
XAUI_GEN2 sets the standard to XAUI_GEN2.

tdcompensation `property` ¶

tdcompensation: MeasurementMeasItemClockrecoveryTdcompensation

Return the MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation command.

Description

This command sets the PLL clock recovery loop feedback time-constants such that the actual transfer function matches closely to a mathematical filter polynomial. This will affect measurements whose : MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 0.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation {0|1}
- MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation?

Info

MEAS<x> specifies the measurement number.
0 specifies automatic transition density compensation is off.
1 specifies automatic transition density compensation is on.

MeasurementMeasItemClockrecoveryAdvanced ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.method: The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod command.

method `property` ¶

method: MeasurementMeasItemClockrecoveryAdvancedMethod

Return the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod command.

Description

This command sets or queries the advanced clock recovery method when advanced clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?

Info

MEAS<x> specifies the measurement number.
NOMinal sets the advanced CRD method to Nominal Data Rate.
PATTern sets the advanced CDR method to use a Known Data Pattern.
NONE sets no advanced CRD method.

MeasurementMeasItemClockrecoveryAdvancedMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod command.

Description

This command sets or queries the advanced clock recovery method when advanced clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod {NONE|NOMinal|PATTern}
- MEASUrement:MEAS<x>:CLOCKRecovery:ADVanced:METHod?

Info

MEAS<x> specifies the measurement number.
NOMinal sets the advanced CRD method to Nominal Data Rate.
PATTern sets the advanced CDR method to use a Known Data Pattern.
NONE sets no advanced CRD method.

MeasurementMeasItemClockrecoveryClockfrequency ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.

Description

This command sets or queries the clock frequency used when fixed constant clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKFrequency?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock frequency.

MeasurementMeasItemClockrecoveryClockmultiplier ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.

Description

This command sets or queries the clock multiplier used when explicit clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock multiplier.

MeasurementMeasItemClockrecoveryConstclockmode ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe command.

Description

This command sets or queries the constant clock mode used when constant clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:CONSTCLOCKMODe {MEAN|MEDian|FIXed}

Info

MEAS<x> specifies the measurement number.
MEAN specifies that clock recovery uses the mean of the clock signal as the clock frequency.
MEDian specifies that clock recovery uses the mode of the clock signal as the clock frequency.
FIXed specifies that clock recovery uses the value set by the user as the clock frequency.

MeasurementMeasItemClockrecoveryDamping ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing command.

Description

This command sets or queries the damping value used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DAMPing?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock recovery damping value.

MeasurementMeasItemClockrecoveryDatapath ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath command.

Description

This command sets or queries the file containing the data pattern used when known data pattern clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath <QString>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATAPath?

Info

MEAS<x> specifies the measurement number.
<QString> is the file containing the data pattern to be used for known data pattern clock recovery.

MeasurementMeasItemClockrecoveryDatarate ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:DATARate command.

Description

This command sets or queries the nominal data bit rate when nominal data rate clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:DATARate value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:DATARate?

Info

MEAS<x> specifies the measurement number.
<NR3> is the value for the Nominal data rate.

MeasurementMeasItemClockrecoveryExplicitclockmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe command.

Description

This command sets or queries the explicit clock mode used when explicit clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe {EDGE|PLL}
- MEASUrement:MEAS<x>:CLOCKRecovery:EXPLICITCLOCKMODe?

Info

MEAS<x> specifies the measurement number.
EDGE specifies the clock edge.
PLL specifies the phase locked loop.

MeasurementMeasItemClockrecoveryGlobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal command.

Description

This command sets or queries the clock recovery settings global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF clock recovery settings are changed independently for each individual measurement.
ON applies global clock recovery settings to all the measurements’ clock recovery settings.
0 clock recovery settings are changed independently for each individual measurement.
1 applies global clock recovery settings to all the measurements’ clock recovery settings.

MeasurementMeasItemClockrecoveryJtfbandwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth command.

Description

This command sets or queries the JTF bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:JTFBandwidth?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock recovery JTF bandwidth.

MeasurementMeasItemClockrecoveryLoopbandwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.

Description

This command sets or queries the loop bandwidth used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:LOOPBandwidth?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock recovery loop bandwidth.

MeasurementMeasItemClockrecoveryMeanautocalculate ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.

Description

This command sets or queries how often the clock is calculated when constant clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- MEASUrement:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?

Info

MEAS<x> specifies the measurement number.
FIRST calculates the clock on the first acquisition.
EVERY calculates the clock on every acquisition.

MeasurementMeasItemClockrecoveryMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:METHod command.

Description

This command sets or queries the clock recovery method for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:METHod {PLL|CONSTANTCLOCK|EXPLICITCLOCK}
- MEASUrement:MEAS<x>:CLOCKRecovery:METHod?

Info

MEAS<x> specifies the measurement number.
PLL specifies a phase locked loop clock recovery method.
CONSTANTCLOCK specifies using a constant clock.
EXPLICITCLOCK specifies using an explicit clock.

MeasurementMeasItemClockrecoveryModel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:MODel command.

Description

This command sets or queries the PLL clock recovery model used when PLL clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MODel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MODel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:MODel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:MODel TYPE<x>
- MEASUrement:MEAS<x>:CLOCKRecovery:MODel?

Info

MEAS<x> specifies the measurement number.
TYPE<x> set the clock recovery model type. Valid values are 1 or 2.

MeasurementMeasItemClockrecoveryNominaloffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.

Description

This command sets or queries the offset value used when explicit clock recovery is used for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset?

Info

MEAS<x> specifies the measurement number.
<NR3> is the clock offset.

Properties

.selectiontype: The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

selectiontype `property` ¶

selectiontype: MeasurementMeasItemClockrecoveryNominaloffsetSelectiontype

Return the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

Description

This command sets or queries the offset type used when explicit clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?

Info

MEAS<x> specifies the measurement number.
AUTO automatically calculates the offset.
MANUAL allows the user to set the offset.

MeasurementMeasItemClockrecoveryNominaloffsetSelectiontype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

Description

This command sets or queries the offset type used when explicit clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- MEASUrement:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?

Info

MEAS<x> specifies the measurement number.
AUTO automatically calculates the offset.
MANUAL allows the user to set the offset.

MeasurementMeasItemClockrecoveryStandard ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:CLOCKRecovery:STAndard command.

Description

This command sets or queries the communications standard when PLL clock recovery is used for the measurement. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:STAndard value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:STAndard {CUSTom|ENET100|FW1394BS400B|FW1394BS800B|FW1394BS1600B|FBD1|FBD2|FBD3|FC133|FC266|FC531|FC1063|FC2125|FC4250|FC8500|ENET1000|IBA2500|IBA_GEN2|OC1|OC3|OC12|OC48|PCIE_GEN1|PCIE_GEN2|PCIE_GEN3|RIO125|RIO250|RIO3125|SAS15_NOSSC|SAS3_NOSSC|SAS6_NOSSC|SAS12_NOSSC|SAS15_SSC|SAS3_SSC|SAS6_SSC|SAS12_SSC|SATA_GEN1|SATA_GEN2|SATA_GEN3|USB3|XAUI|XAUI_GEN2}

Info

MEAS<x> specifies the measurement number.
CUSTom sets the standard to custom.
ENET100 sets the standard to ENET100.
FW1394BS400B sets the standard to FW1394BS400B.
FW1394BS800B sets the standard to FW1394BS800B.
FW1394BS1600B sets the standard to FW1394BS1600B.
FBD1 sets the standard to FBD1.
FBD2 sets the standard to FBD2.
FBD3 sets the standard to FBD3.
FC133 sets the standard to FC133.
FC266 sets the standard to FC266.
FC531 sets the standard to FC531.
FC1063 sets the standard to FC1063.
FC2125 sets the standard to FC2125.
FC4250 sets the standard to FC4250.
FC8500 sets the standard to FC8500.
ENET1000 sets the standard to ENET1000.
IBA2500 sets the standard to IBA2500.
IBA_GEN2 sets the standard to IBA_GEN2.
OC1 sets the standard to OC1.
OC3 sets the standard to OC3.
OC12 sets the standard to OC12.
OC48 sets the standard to OC48.
PCIE_GEN1 sets the standard to PCIE_GEN1.
PCIE_GEN2 sets the standard to PCIE_GEN2.
PCIE_GEN3 sets the standard to PCIE_GEN3.
RIO125 sets the standard to RIO125.
RIO250 sets the standard to RIO250.
RIO3125 sets the standard to RIO3125.
SAS15_NOSSC sets the standard to SAS15_NOSSC.
SAS3_NOSSC sets the standard to SAS3_NOSSC.
SAS6_NOSSC sets the standard to SAS6_NOSSC.
SAS12_NOSSC sets the standard to SAS12_NOSSC.
SAS15_SSC sets the standard to SAS15_SSC.
SAS3_SSC sets the standard to SAS3_SSC.
SAS6_SSC sets the standard to SAS6_SSC.
SAS12_SSC sets the standard to SAS12_SSC.
SATA_GEN1 sets the standard to SATA_GEN1.
SATA_GEN2 sets the standard to SATA_GEN2.
SATA_GEN3 sets the standard to SATA_GEN3.
USB3 sets the standard to USB3.
XAUI sets the standard to XAUI.
XAUI_GEN2 sets the standard to XAUI_GEN2.

MeasurementMeasItemClockrecoveryTdcompensation ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation command.

Description

This command sets the PLL clock recovery loop feedback time-constants such that the actual transfer function matches closely to a mathematical filter polynomial. This will affect measurements whose : MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 0.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation {0|1}
- MEASUrement:MEAS<x>:CLOCKRecovery:TDCOMPensation?

Info

MEAS<x> specifies the measurement number.
0 specifies automatic transition density compensation is off.
1 specifies automatic transition density compensation is on.

MeasurementMeasItemCommonmode ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:COMMONMode command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.filters: The MEASUrement:MEAS<x>:COMMONMode:FILTers command tree.
.sources: The MEASUrement:MEAS<x>:COMMONMode:SOURCEs command.

filters `property` ¶

filters: MeasurementMeasItemCommonmodeFilters

Return the MEASUrement:MEAS<x>:COMMONMode:FILTers command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.state: The MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE command.

sources `property` ¶

sources: MeasurementMeasItemCommonmodeSources

Return the MEASUrement:MEAS<x>:COMMONMode:SOURCEs command.

Description

This command sets or queries the number of sources for the measurement when the measurement type is AC common mode. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode:SOURCEs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode:SOURCEs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:COMMONMode:SOURCEs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:COMMONMode:SOURCEs {SINGLE|DOUBLE}
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs?

Info

MEAS<x> specifies the measurement number.
SINGLE specifies a single source.
DOUBLE specifies double sources.

MeasurementMeasItemCommonmodeFilters ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:COMMONMode:FILTers command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.state: The MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE command.

state `property` ¶

state: MeasurementMeasItemCommonmodeFiltersState

Return the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE command.

Description

This command sets or queries whether a filter is used for the measurement when the measurement type is AC common mode. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?

Info

MEAS<x> specifies the measurement number.
OFF turns the filter off.
ON turns the filter on.
0 turns the filter off.
1 turns the filter on.

MeasurementMeasItemCommonmodeFiltersState ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE command.

Description

This command sets or queries whether a filter is used for the measurement when the measurement type is AC common mode. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:COMMONMode:FILTers:STATE?

Info

MEAS<x> specifies the measurement number.
OFF turns the filter off.
ON turns the filter on.
0 turns the filter off.
1 turns the filter on.

MeasurementMeasItemCommonmodeSources ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:COMMONMode:SOURCEs command.

Description

This command sets or queries the number of sources for the measurement when the measurement type is AC common mode. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COMMONMode:SOURCEs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COMMONMode:SOURCEs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:COMMONMode:SOURCEs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:COMMONMode:SOURCEs {SINGLE|DOUBLE}
- MEASUrement:MEAS<x>:COMMONMode:SOURCEs?

Info

MEAS<x> specifies the measurement number.
SINGLE specifies a single source.
DOUBLE specifies double sources.

MeasurementMeasItemCover ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:COVer command.

Description

This command sets or queries the Calculate Over for the Power Quality measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:COVer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:COVer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:COVer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:COVer {FFREQuency|AFREQuencies}
- MEASUrement:MEAS<x>:COVer?

Info

FFREQuency sets Calculate Power Quality measurement.
AFREQuencies sets Calculate Power Quality measurement for all frequencies.

MeasurementMeasItemCpwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CPWIDTh command.

Description

This command sets or queries the channel power width for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CPWIDTh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CPWIDTh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CPWIDTh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CPWIDTh <NR3>
- MEASUrement:MEAS<x>:CPWIDTh?

Info

<NR3> is the channel power width. The default value is 10.0e6 and the valid range is 1.0e3 to 8.0e9.

MeasurementMeasItemCspacing ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CSPACing command.

Description

This command sets or queries the channel spacing for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CSPACing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CSPACing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CSPACing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CSPACing <NR3>
- MEASUrement:MEAS<x>:CSPACing?

Info

<NR3> is the channel spacing. The default value is 5.0e6 and the valid range is 1.0e3 to 8.0e9.

MeasurementMeasItemCustomlimitsfile ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CUSTOMLIMITSFile command.

Description

This command sets or queries the custom limits file path for custom harmonics standard. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CUSTOMLIMITSFile? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CUSTOMLIMITSFile? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CUSTOMLIMITSFile value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CUSTOMLIMITSFile <QString>
- MEASUrement:MEAS<x>:CUSTOMLIMITSFile?

Info

MEAS<x> specifies the measurement number.
<QString> specifies the location of limits file.

MeasurementMeasItemCyclemode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:CYCLemode command.

Description

This command sets or queries the cycle mode for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:CYCLemode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:CYCLemode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:CYCLemode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:CYCLemode {RECORD|CYCLE|ROTATION}
- MEASUrement:MEAS<x>:CYCLemode?

Info

MEAS<x> specifies the measurement number.
RECORD specifies that the measurement is taken over the whole record.
CYCLE specifies that measurements are taken on each cycle of the source.
ROTATION specifies that measurements are taken on a rotation of the source.

MeasurementMeasItemDbdown ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:DBDown command.

Description

This command sets or queries the dB down value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DBDown? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DBDown? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DBDown value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DBDown <NR3>
- MEASUrement:MEAS<x>:DBDown?

Info

<NR3> sets the dB down value. The default value is -26 and the valid range is -80 to -1.

MeasurementMeasItemDelay ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:DELay command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.edge: The MEASUrement:MEAS<x>:DELay:EDGE<x> command.

edge `property` ¶

edge: dict[int, MeasurementMeasItemDelayEdgeItem]

Return the MEASUrement:MEAS<x>:DELay:EDGE<x> command.

Description

This command sets or queries the ‘to edge’ type when EDGE is EDGE1 and the ‘from edge’ type when EDGE is EDG2, for the measurement when the measurement type is DELAY. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISe specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

MeasurementMeasItemDelayEdgeItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:DELay:EDGE<x> command.

Description

This command sets or queries the ‘to edge’ type when EDGE is EDGE1 and the ‘from edge’ type when EDGE is EDG2, for the measurement when the measurement type is DELAY. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DELay:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DELay:EDGE<x> {FALL|RISe|BOTH|SAMEas|OPPositeas}
- MEASUrement:MEAS<x>:DELay:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISe specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

MeasurementMeasItemDisplaystat ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:DISPlaystat command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.enable: The MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

enable `property` ¶

enable: MeasurementMeasItemDisplaystatEnable

Return the MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

Description

This command turns on and off display of statistics in measurement badges in the user interface. This command affects only the display of statistics, basic-statistics are computed regardless of the state of this command. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?

Info

MEAS<x> specifies the measurement number.
OFF turns off the display of statistics in measurement badges.
ON turns on the display of statistics in measurement badges.
<NR1> = 0 turns off the display of statistics in the measurement badge, any other value turns on the display of statistics.

MeasurementMeasItemDisplaystatEnable ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:DISPlaystat:ENABle command.

Description

This command turns on and off display of statistics in measurement badges in the user interface. This command affects only the display of statistics, basic-statistics are computed regardless of the state of this command. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DISPlaystat:ENABle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DISPlaystat:ENABle {ON|OFF|<NR1>}
- MEASUrement:MEAS<x>:DISPlaystat:ENABle?

Info

MEAS<x> specifies the measurement number.
OFF turns off the display of statistics in measurement badges.
ON turns on the display of statistics in measurement badges.
<NR1> = 0 turns off the display of statistics in the measurement badge, any other value turns on the display of statistics.

MeasurementMeasItemDmethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:DMEThod command.

Description

This command sets or returns the deskew method for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DMEThod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DMEThod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DMEThod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DMEThod {AUTO|MANual}
- MEASUrement:MEAS<x>:DMEThod?

Info

AUTO or MANual specifies the deskew method set for WBG measurement.

MeasurementMeasItemDvds ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:DVDS command.

Description

This command enabled or disables display state of the derived Vds waveform for RDS(on) measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:DVDS? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:DVDS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:DVDS value command.

SCPI Syntax

- MEASUrement:MEAS<x>:DVDS {OFF|ON}
- MEASUrement:MEAS<x>:DVDS?

Info

MEAS<x> specifies the measurement number.
OFF specifies that derived Vds waveform display is disabled for RDS(on) measurement.
ON specifies that derived Vds waveform display is enabled for RDS(on) measurement.

MeasurementMeasItemEdgeItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGE<x> command.

Description

This command sets or queries the type of the specified edge, rise or fall, for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGE<x>? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGE<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGE<x> value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGE<x> {RISE|FALL|BOTH}
- MEASUrement:MEAS<x>:EDGE<x>?

Info

MEAS<x> specifies the measurement number.
RISE specifies the rising edge.
FALL specifies the falling edge.
BOTH specifies either the rising or falling edge.

MeasurementMeasItemEdgeincre ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGEIncre command.

Description

This command sets or queries the edge increment value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEIncre? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEIncre? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEIncre value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEIncre <NR3>
- MEASUrement:MEAS<x>:EDGEIncre?

Info

MEAS<x> specifies the measurement number.
<NR3> is the measurements edge increment value.

MeasurementMeasItemEdgequalifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGEQUALifier command.

Description

This command sets or queries the edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEQUALifier value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:EDGEQUALifier?

Info

MEAS<x> is the measurement number.
CH<x> is the edge qualifier source channel.
MATH<x> is the edge qualifier source math waveform; is ≥1.
REF<x> is the edge qualifier source reference waveform; is ≥1.

MeasurementMeasItemEdgequalone ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGEQUALONE command.

Description

This command set or queries the measurement 1 input edge qualifier one source for Efficiency measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEQUALONE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEQUALONE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEQUALONE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEQUALONE <QString>
- MEASUrement:MEAS<x>:EDGEQUALONE?

Info

MEAS<x> is the measurement number.
<QString> specifies the edge qualifier source at input configuration.

MeasurementMeasItemEdgequaltwo ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGEQUALTWO command.

Description

This command sets or queries the measurement 1 output edge qualifier two source for Efficiency measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGEQUALTWO? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGEQUALTWO? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGEQUALTWO value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGEQUALTWO <QString>
- MEASUrement:MEAS<x>:EDGEQUALTWO?

Info

MEAS<x> is the measurement number.
<QString> specifies the edge qualifier source at output configuration.

MeasurementMeasItemEdges ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:EDGES command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.fromlevel: The MEASUrement:MEAS<x>:EDGES:FROMLevel command.
.level: The MEASUrement:MEAS<x>:EDGES:LEVel command.
.lowerfrequency: The MEASUrement:MEAS<x>:EDGES:LOWERFREQuency command.
.n: The MEASUrement:MEAS<x>:EDGES:N command.
.slewratemethod: The MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.
.tolevel: The MEASUrement:MEAS<x>:EDGES:TOLevel command.
.upperfrequency: The MEASUrement:MEAS<x>:EDGES:UPPERFREQuency command.

fromlevel `property` ¶

fromlevel: MeasurementMeasItemEdgesFromlevel

Return the MEASUrement:MEAS<x>:EDGES:FROMLevel command.

Description

This command sets or queries the ‘from level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?

Info

MEAS<x> specifies the measurement number.
MID specifies the MID level.
HIGH specifies the HIGH level.
LOW specifies the LOW level.

level `property` ¶

level: MeasurementMeasItemEdgesLevel

Return the MEASUrement:MEAS<x>:EDGES:LEVel command.

Description

This sets or queries the level type for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
LOW specifies the LOW level.
BOTH specifies both the HIGH and LOW level.

lowerfrequency `property` ¶

lowerfrequency: MeasurementMeasItemEdgesLowerfrequency

Return the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency command.

Description

This command sets or queries the lower frequency for the measurement when the measurement type is phase noise. Lower frequencies are ignored. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency?

Info

MEAS<x> specifies the measurement number.
<NR3> is the lower frequency of the edge.

n `property` ¶

n: MeasurementMeasItemEdgesN

Return the MEASUrement:MEAS<x>:EDGES:N command.

Description

The command sets or queries the number of accumulation cycles for the measurement when the measurement type is nperiod. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?

Info

MEAS<x> specifies the measurement number.
<NR3> is the maximum number of edges used by the measurement.

slewratemethod `property` ¶

slewratemethod: MeasurementMeasItemEdgesSlewratemethod

Return the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.

Description

This command sets or queries the slew rate method for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?

Info

MEAS<x> specifies the measurement number.
NOMinal specifies the nominal slew rate method.
DDR specifies the DDR slew rate method.

tolevel `property` ¶

tolevel: MeasurementMeasItemEdgesTolevel

Return the MEASUrement:MEAS<x>:EDGES:TOLevel command.

Description

This command sets or queries the ‘to level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
MID specifies the MID level.
LOW specifies the LOW level.

upperfrequency `property` ¶

upperfrequency: MeasurementMeasItemEdgesUpperfrequency

Return the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency command.

Description

This command sets or queries the upper frequency for the measurement when the measurement type is phase noise. Higher frequencies are ignored. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency?

Info

MEAS<x> specifies the measurement number.
<NR3> is the upper frequency of the edge.

MeasurementMeasItemEdgesFromlevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:FROMLevel command.

Description

This command sets or queries the ‘from level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:FROMLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:FROMLevel {MID|LOW|HIGH}
- MEASUrement:MEAS<x>:EDGES:FROMLevel?

Info

MEAS<x> specifies the measurement number.
MID specifies the MID level.
HIGH specifies the HIGH level.
LOW specifies the LOW level.

MeasurementMeasItemEdgesLevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:LEVel command.

Description

This sets or queries the level type for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:LEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:LEVel {HIGH|LOW|BOTH}
- MEASUrement:MEAS<x>:EDGES:LEVel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
LOW specifies the LOW level.
BOTH specifies both the HIGH and LOW level.

MeasurementMeasItemEdgesLowerfrequency ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:LOWERFREQuency command.

Description

This command sets or queries the lower frequency for the measurement when the measurement type is phase noise. Lower frequencies are ignored. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:LOWERFREQuency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:LOWERFREQuency?

Info

MEAS<x> specifies the measurement number.
<NR3> is the lower frequency of the edge.

MeasurementMeasItemEdgesN ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:N command.

Description

The command sets or queries the number of accumulation cycles for the measurement when the measurement type is nperiod. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:N <NR3>
- MEASUrement:MEAS<x>:EDGES:N?

Info

MEAS<x> specifies the measurement number.
<NR3> is the maximum number of edges used by the measurement.

MeasurementMeasItemEdgesSlewratemethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod command.

Description

This command sets or queries the slew rate method for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod {NOMinal|DDR}
- MEASUrement:MEAS<x>:EDGES:SLEWRATEMethod?

Info

MEAS<x> specifies the measurement number.
NOMinal specifies the nominal slew rate method.
DDR specifies the DDR slew rate method.

MeasurementMeasItemEdgesTolevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:TOLevel command.

Description

This command sets or queries the ‘to level’ edge for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:TOLevel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- MEASUrement:MEAS<x>:EDGES:TOLevel?

Info

MEAS<x> specifies the measurement number.
HIGH specifies the HIGH level.
MID specifies the MID level.
LOW specifies the LOW level.

MeasurementMeasItemEdgesUpperfrequency ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EDGES:UPPERFREQuency command.

Description

This command sets or queries the upper frequency for the measurement when the measurement type is phase noise. Higher frequencies are ignored. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EDGES:UPPERFREQuency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency <NR3>
- MEASUrement:MEAS<x>:EDGES:UPPERFREQuency?

Info

MEAS<x> specifies the measurement number.
<NR3> is the upper frequency of the edge.

MeasurementMeasItemEequal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EEQUal command.

Description

This command turns on or off the edge qualifier settings as input waveform to measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EEQUal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EEQUal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EEQUal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EEQUal {ON|OFF}
- MEASUrement:MEAS<x>:EEQUal?

Info

MEAS<x> specifies the measurement number.
ON specifies the edge qualifier settings has been turned on.
OFF specifies the edge qualifier settings has been turned off.

MeasurementMeasItemEinductance ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EINDuctance command.

Description

This command sets or returns the effective inductance for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EINDuctance? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EINDuctance? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EINDuctance value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EINDuctance <NR3>
- MEASUrement:MEAS<x>:EINDuctance?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for effective inductance of the WBG measurement.

MeasurementMeasItemEinterpolation ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EINTerpolation command.

Description

This command sets or queries whether dot mode eye diagram is enabled.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EINTerpolation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EINTerpolation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EINTerpolation value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EINTerpolation {ON|OFF}
- MEASUrement:MEAS<x>:EINTerpolation?

Info

MEAS<x> specifies the measurement number.
ON enables interpolation between samples.
OFF disables interpolation between samples.

MeasurementMeasItemExtenduis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EXTENDuis command.

Description

This command sets or returns number of UIs considered for analysis of eye width or eye height measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EXTENDuis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EXTENDuis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EXTENDuis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EXTENDuis <NR1>
- MEASUrement:MEAS<x>:EXTENDuis?

Info

MEAS<x> specifies the measurement number.
<NR1> is the number of UIs considered for analysis.

MeasurementMeasItemEyerender ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:EYERender command.

Description

This command sets or queries the eye rendering method.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:EYERender? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:EYERender? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:EYERender value command.

SCPI Syntax

- MEASUrement:MEAS<x>:EYERender {FAst|COMPlete}
- MEASUrement:MEAS<x>:EYERender?

Info

MEAS<x> specifies the measurement number.
FAst sets the eye rendering method to fast.
COMPlete sets the eye rendering method to complete.

MeasurementMeasItemFailcount ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:FAILCount command.

Description

This command returns the number of measurement failures, if applicable, for the selected measure The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FAILCount? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FAILCount? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:FAILCount?

MeasurementMeasItemFcount ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FCOunt command.

Description

This command sets or returns the filter count for PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FCOunt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FCOunt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FCOunt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FCOunt <NR3>
- MEASUrement:MEAS<x>:FCOunt?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the number of filters applied for PSIJ measurement.

MeasurementMeasItemFilterrangefrom ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTERRANGEFROM command.

Description

This command sets or queries harmonics filter from order. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTERRANGEFROM? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTERRANGEFROM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTERRANGEFROM value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTERRANGEFROM <NR3>
- MEASUrement:MEAS<x>:FILTERRANGEFROM?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the filter range from value. The default value is 1.

MeasurementMeasItemFilterrangeto ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTERRANGETO command.

Description

This command sets or queries harmonics filter to order. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTERRANGETO? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTERRANGETO? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTERRANGETO value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTERRANGETO <NR3>
- MEASUrement:MEAS<x>:FILTERRANGETO?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the filter range to value. The default value is 50.

MeasurementMeasItemFilters ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:FILTers command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.blankingtime: The MEASUrement:MEAS<x>:FILTers:BLANKingtime command.
.global: The MEASUrement:MEAS<x>:FILTers:GLOBal command.
.highpass: The MEASUrement:MEAS<x>:FILTers:HIGHPass command tree.
.lowpass: The MEASUrement:MEAS<x>:FILTers:LOWPass command tree.
.ramptime: The MEASUrement:MEAS<x>:FILTers:RAMPtime command.

blankingtime `property` ¶

blankingtime: MeasurementMeasItemFiltersBlankingtime

Return the MEASUrement:MEAS<x>:FILTers:BLANKingtime command.

Description

This command sets or queries the filter blanking time for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:BLANKingtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:BLANKingtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:BLANKingtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:BLANKingtime <NR3>
- MEASUrement:MEAS<x>:FILTers:BLANKingtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current filter blanking time.

global_ `property` ¶

global_: MeasurementMeasItemFiltersGlobal

Return the MEASUrement:MEAS<x>:FILTers:GLOBal command.

Description

This command sets or queries the global flag for filter settings for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:FILTers:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF causes filter settings to be changed independently for each individual measurement.
ON applies global filter settings to all the measurements’ filter settings.
0 causes filter settings to be changed independently for each individual measurement.
1 applies global filter settings to all the measurements’ filter settings.

highpass `property` ¶

highpass: MeasurementMeasItemFiltersHighpass

Return the MEASUrement:MEAS<x>:FILTers:HIGHPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.freq: The MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC command.

lowpass `property` ¶

lowpass: MeasurementMeasItemFiltersLowpass

Return the MEASUrement:MEAS<x>:FILTers:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.freq: The MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC command.

ramptime `property` ¶

ramptime: MeasurementMeasItemFiltersRamptime

Return the MEASUrement:MEAS<x>:FILTers:RAMPtime command.

Description

This command sets or queries the filter ramp time for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:RAMPtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:RAMPtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:RAMPtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:RAMPtime <NR3>
- MEASUrement:MEAS<x>:FILTers:RAMPtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current filter ramp time.

MeasurementMeasItemFiltersBlankingtime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:BLANKingtime command.

Description

This command sets or queries the filter blanking time for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:BLANKingtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:BLANKingtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:BLANKingtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:BLANKingtime <NR3>
- MEASUrement:MEAS<x>:FILTers:BLANKingtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current filter blanking time.

MeasurementMeasItemFiltersGlobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:GLOBal command.

Description

This command sets or queries the global flag for filter settings for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:FILTers:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF causes filter settings to be changed independently for each individual measurement.
ON applies global filter settings to all the measurements’ filter settings.
0 causes filter settings to be changed independently for each individual measurement.
1 applies global filter settings to all the measurements’ filter settings.

MeasurementMeasItemFiltersHighpass ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:HIGHPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.freq: The MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC command.

freq `property` ¶

freq: MeasurementMeasItemFiltersHighpassFreq

Return the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ command.

Description

This command sets or queries the high pass filter frequency for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current high pass filter frequency.

spec `property` ¶

spec: MeasurementMeasItemFiltersHighpassSpec

Return the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC command.

Description

This command sets or queries the high pass filter order for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies no filter.
FIRST specifies a first-order filter.
SECOND specifies a second-order filter.
THIRD specifies a third-order filter.

MeasurementMeasItemFiltersHighpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ command.

Description

This command sets or queries the high pass filter frequency for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:HIGHPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current high pass filter frequency.

MeasurementMeasItemFiltersHighpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC command.

Description

This command sets or queries the high pass filter order for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:HIGHPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies no filter.
FIRST specifies a first-order filter.
SECOND specifies a second-order filter.
THIRD specifies a third-order filter.

MeasurementMeasItemFiltersLowpass ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.freq: The MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC command.

freq `property` ¶

freq: MeasurementMeasItemFiltersLowpassFreq

Return the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ command.

Description

This command sets or queries the low pass filter cutoff frequency for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.

spec `property` ¶

spec: MeasurementMeasItemFiltersLowpassSpec

Return the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC command.

Description

This command sets or queries the low pass filter order for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies no filter.
FIRST specifies a first-order filter.
SECOND specifies a second-order filter.
THIRD specifies a third-order filter.

MeasurementMeasItemFiltersLowpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ command.

Description

This command sets or queries the low pass filter cutoff frequency for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:FILTers:LOWPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current low pass filter frequency. The argument range is 20 Hz to 10e6 Hz.

MeasurementMeasItemFiltersLowpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC command.

Description

This command sets or queries the low pass filter order for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:FILTers:LOWPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies no filter.
FIRST specifies a first-order filter.
SECOND specifies a second-order filter.
THIRD specifies a third-order filter.

MeasurementMeasItemFiltersRamptime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FILTers:RAMPtime command.

Description

This command sets or queries the filter ramp time for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FILTers:RAMPtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FILTers:RAMPtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FILTers:RAMPtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FILTers:RAMPtime <NR3>
- MEASUrement:MEAS<x>:FILTers:RAMPtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the current filter ramp time.

MeasurementMeasItemForder ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FORDer command.

Description

This command sets or returns the differential filter order for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FORDer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FORDer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FORDer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FORDer <NR3>
- MEASUrement:MEAS<x>:FORDer?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the differential filter order of the WBG measurement.

MeasurementMeasItemFparameter ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FPARAmeter command.

Description

This command sets or queries the roll off factor for the RRC filter in the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FPARAmeter? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FPARAmeter? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FPARAmeter value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FPARAmeter <NR3>
- MEASUrement:MEAS<x>:FPARAmeter?

Info

<NR3> sets the roll off factor. The default is 0.22. The valid range is from 0.001 to 1.0.

MeasurementMeasItemFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FREQ command.

Description

This command sets or queries switching frequency for Switching Ripple measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FREQ <NR3>
- MEASUrement:MEAS<x>:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the switching frequency. The default is 100k Hz, The minimum is 50 Hz, and the maximum is 1 GHz.

MeasurementMeasItemFromedge ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMedge command.

Description

This command sets or queries the from edge type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMedge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMedge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMedge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:FROMedge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISe specifies the rising edge of the waveform.
BOTH specifies both the rising and falling edges of the waveform.

MeasurementMeasItemFromedgesearchdirect ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect command.

Description

This command sets or queries the from edge search direction for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:FROMEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search from the edge.
BACKWard specifies a backward search from the edge.

MeasurementMeasItemFromsymbol ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:FROMSymbol command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.logic2source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce command.
.logic3source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce command.
.logic4source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce command.
.logic5source: The MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce command.
.measureat: The MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT command.

logic2source `property` ¶

logic2source: MeasurementMeasItemFromsymbolLogic2source

Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 1 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 1 From Symbol to H (High).
L sets the logic source 1 From Symbol to L (Low).
X sets the logic source 1 From Symbol to X (Don’t care).

logic3source `property` ¶

logic3source: MeasurementMeasItemFromsymbolLogic3source

Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 2 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 2 From Symbol to H (High).
L sets the logic source 2 From Symbol to L (Low).
X sets the logic source 2 From Symbol to X (Don’t care).

logic4source `property` ¶

logic4source: MeasurementMeasItemFromsymbolLogic4source

Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 3 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 3 From Symbol to H (High).
L sets the logic source 3 From Symbol to L (Low).
X sets the logic source 3 From Symbol to X (Don’t care).

logic5source `property` ¶

logic5source: MeasurementMeasItemFromsymbolLogic5source

Return the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 4 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 4 From Symbol to H (High).
L sets the logic source 4 From Symbol to L (Low).
X sets the logic source 4 From Symbol to X (Don’t care).

measureat `property` ¶

measureat: MeasurementMeasItemFromsymbolMeasureat

Return the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT command.

Description

This command sets or queries the DDR digital measurement From Symbol MeasureAT value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?

Info

MEAS<x> specifies the measurement number.
Start sets the FromSymbol MeasureAT to Start.
Stop sets the FromSymbol MeasureAT to Stop.
ClockEdge sets the FromSymbol MeasureAT to ClockEdge.

MeasurementMeasItemFromsymbolLogic2source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 1 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC2SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 1 From Symbol to H (High).
L sets the logic source 1 From Symbol to L (Low).
X sets the logic source 1 From Symbol to X (Don’t care).

MeasurementMeasItemFromsymbolLogic3source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 2 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC3SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 2 From Symbol to H (High).
L sets the logic source 2 From Symbol to L (Low).
X sets the logic source 2 From Symbol to X (Don’t care).

MeasurementMeasItemFromsymbolLogic4source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 3 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC4SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 3 From Symbol to H (High).
L sets the logic source 3 From Symbol to L (Low).
X sets the logic source 3 From Symbol to X (Don’t care).

MeasurementMeasItemFromsymbolLogic5source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 4 source From symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:FROMSymbol:LOGIC5SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 4 From Symbol to H (High).
L sets the logic source 4 From Symbol to L (Low).
X sets the logic source 4 From Symbol to X (Don’t care).

MeasurementMeasItemFromsymbolMeasureat ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT command.

Description

This command sets or queries the DDR digital measurement From Symbol MeasureAT value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:FROMSymbol:MEASUREAT?

Info

MEAS<x> specifies the measurement number.
Start sets the FromSymbol MeasureAT to Start.
Stop sets the FromSymbol MeasureAT to Stop.
ClockEdge sets the FromSymbol MeasureAT to ClockEdge.

MeasurementMeasItemFtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FTYPe command.

Description

This command sets or returns whether the RRC filter is enabled or not. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FTYPe {True|False}
- MEASUrement:MEAS<x>:FTYPe?

Info

True enables the RRC filter.
False disables the RRC filter.

MeasurementMeasItemFundcurrent ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:FUNDCURRent command.

Description

This command sets or queries the fundamental current value for IEC-Class C type harmonics standard. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:FUNDCURRent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:FUNDCURRent? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:FUNDCURRent value command.

SCPI Syntax

- MEASUrement:MEAS<x>:FUNDCURRent <NR3>
- MEASUrement:MEAS<x>:FUNDCURRent?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the fundamental current for class C harmonics standard.

MeasurementMeasItemGating ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing command.

Description

This command sets or queries the gating type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing {NONE|SCREEN|CURSor|LOGic|SEARch|TIMe}
- MEASUrement:MEAS<x>:GATing?

Info

MEAS<x> is the measurement number for which to return a value.
NONE specifies measurements are taken across the entire record.
SCREEN turns on gating, using the left and right edges of the screen.
CURSor limits measurements to the portion of the waveform between the vertical bar cursors, even if they are off screen.
LOGic specifies that measurements are taken only when the logical state of other waveforms is true.
SEARch specifies that measurements are taken only where the results of a user specified search are found.
TIMe limits measurements to the portion of the waveform between the Start and End gate times.

Properties

.active: The MEASUrement:MEAS<x>:GATing:ACTive command.
.endtime: The MEASUrement:MEAS<x>:GATing:ENDtime command.
.global: The MEASUrement:MEAS<x>:GATing:GLOBal command.
.hysteresis: The MEASUrement:MEAS<x>:GATing:HYSTeresis command.
.logicsource: The MEASUrement:MEAS<x>:GATing:LOGICSource command.
.midref: The MEASUrement:MEAS<x>:GATing:MIDRef command.
.searchsource: The MEASUrement:MEAS<x>:GATing:SEARCHSource command.
.starttime: The MEASUrement:MEAS<x>:GATing:STARTtime command.

active `property` ¶

active: MeasurementMeasItemGatingActive

Return the MEASUrement:MEAS<x>:GATing:ACTive command.

Description

This command sets or queries the gating active level when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?

Info

MEAS<x> specifies the measurement number.
HIGH takes a measurement when logic gating is High.
LOW takes a measurement when logic gating Low.

endtime `property` ¶

endtime: MeasurementMeasItemGatingEndtime

Return the MEASUrement:MEAS<x>:GATing:ENDtime command.

Description

Sets or queries the end gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

global_ `property` ¶

global_: MeasurementMeasItemGatingGlobal

Return the MEASUrement:MEAS<x>:GATing:GLOBal command.

Description

This command sets or queries the gating settings global flag. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies gate settings can be changed independently for each individual measurement.
ON applies global gate settings to all the measurements’ gate settings.
0 specifies gate settings can be changed independently for each individual measurement.
1 applies global gate settings to all the measurements’ gate settings.

hysteresis `property` ¶

hysteresis: MeasurementMeasItemGatingHysteresis

Return the MEASUrement:MEAS<x>:GATing:HYSTeresis command.

Description

This command sets or queries the gating hysteresis value when the gating type is logic. Measurements are specified by x. This command sets or queries the global file containing the data pattern used when known data pattern clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the gating hysteresis.

logicsource `property` ¶

logicsource: MeasurementMeasItemGatingLogicsource

Return the MEASUrement:MEAS<x>:GATing:LOGICSource command.

Description

This command sets or queries the gating data source when the gating type is logic. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}

Info

MEAS<x> specifies the measurement number.
CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

midref `property` ¶

midref: MeasurementMeasItemGatingMidref

Return the MEASUrement:MEAS<x>:GATing:MIDRef command.

Description

This command sets or queries the gating mid ref value when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid ref value for gating.

searchsource `property` ¶

searchsource: MeasurementMeasItemGatingSearchsource

Return the MEASUrement:MEAS<x>:GATing:SEARCHSource command.

Description

This command sets or queries the gating search source when the gating type is search. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
- MEASUrement:MEAS<x>:GATing:SEARCHSource?

Info

MEAS<x> specifies the measurement number.
SEARCH1 is the gating source for search gating.

starttime `property` ¶

starttime: MeasurementMeasItemGatingStarttime

Return the MEASUrement:MEAS<x>:GATing:STARTtime command.

Description

Sets or queries the start gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementMeasItemGatingActive ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:ACTive command.

Description

This command sets or queries the gating active level when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ACTive? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ACTive value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ACTive {HIGH|LOW}
- MEASUrement:MEAS<x>:GATing:ACTive?

Info

MEAS<x> specifies the measurement number.
HIGH takes a measurement when logic gating is High.
LOW takes a measurement when logic gating Low.

MeasurementMeasItemGatingEndtime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:ENDtime command.

Description

Sets or queries the end gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:ENDtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:ENDtime <NR3>
- MEASUrement:MEAS<x>:GATing:ENDtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating end gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementMeasItemGatingGlobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:GLOBal command.

Description

This command sets or queries the gating settings global flag. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GATing:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies gate settings can be changed independently for each individual measurement.
ON applies global gate settings to all the measurements’ gate settings.
0 specifies gate settings can be changed independently for each individual measurement.
1 applies global gate settings to all the measurements’ gate settings.

MeasurementMeasItemGatingHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:HYSTeresis command.

Description

This command sets or queries the gating hysteresis value when the gating type is logic. Measurements are specified by x. This command sets or queries the global file containing the data pattern used when known data pattern clock recovery is used for the measurement. This will affect measurements whose :MEASUrement:MEAS<x>:CLOCKRecovery:GLOBal flag is set to 1.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:GATing:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the gating hysteresis.

MeasurementMeasItemGatingLogicsource ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:GATing:LOGICSource command.

Description

This command sets or queries the gating data source when the gating type is logic. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:LOGICSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:LOGICSource {CH<x>|MATH<x>|REF<x>}

Info

MEAS<x> specifies the measurement number.
CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementMeasItemGatingMidref ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:MIDRef command.

Description

This command sets or queries the gating mid ref value when the gating type is logic. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:MIDRef value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:MIDRef <NR3>
- MEASUrement:MEAS<x>:GATing:MIDRef?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid ref value for gating.

MeasurementMeasItemGatingSearchsource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:SEARCHSource command.

Description

This command sets or queries the gating search source when the gating type is search. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:SEARCHSource value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:SEARCHSource SEARCH1
- MEASUrement:MEAS<x>:GATing:SEARCHSource?

Info

MEAS<x> specifies the measurement number.
SEARCH1 is the gating source for search gating.

MeasurementMeasItemGatingStarttime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GATing:STARTtime command.

Description

Sets or queries the start gate time for the measurement when using Local gating.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GATing:STARTtime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GATing:STARTtime <NR3>
- MEASUrement:MEAS<x>:GATing:STARTtime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the time gating start gate time in seconds. The valid range is -10000 s to 10000 s.

MeasurementMeasItemGlobalref ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:GLOBalref command.

Description

This command sets or queries the reference levels global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:GLOBalref? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:GLOBalref? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:GLOBalref value command.

SCPI Syntax

- MEASUrement:MEAS<x>:GLOBalref {ON|OFF|1|0}
- MEASUrement:MEAS<x>:GLOBalref?

Info

MEAS<x> specifies the measurement number.
OFF allows ref levels to be set separately for each measurement.
ON applies the same ref levels to all measurements.
0 allows ref levels to be set separately for each measurement.
1 applies the same ref levels to all measurements.

MeasurementMeasItemHarmonicsclass ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HARMONICSCLass command.

Description

This command sets or queries the class type for the harmonics measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSCLass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSCLass? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSCLass value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSCLass {CLASSA|CLASSB|CLASSC|CLASSD}
- MEASUrement:MEAS<x>:HARMONICSCLass?

Info

MEAS<x> specifies the measurement number.
CLASSA specifies the class type to A.
CLASSB specifies the class type to B.
CLASSC specifies the class type to C.
CLASSD specifies the class type to D.

MeasurementMeasItemHarmonicssource ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HARMONICSSOURce command.

Description

This command sets or queries harmonics source. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSSOURce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSSOURce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSSOURce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSSOURce {CURRENT|VOLTAGE}
- MEASUrement:MEAS<x>:HARMONICSSOURce?

Info

MEAS<x> specifies the measurement number.
CURRENT specifies current as the harmonics source.
VOLTAGE specifies voltage as the harmonics source.

MeasurementMeasItemHarmonicsstd ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HARMONICSStd command.

Description

This command sets or queries harmonics standard. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSStd? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSStd? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSStd value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSStd {NONE|IEC|IEEE519|CUSTOM|REVIEEE5192022}
- MEASUrement:MEAS<x>:HARMONICSStd?

Info

MEAS<x> specifies the measurement number.
NONE specifies none as the harmonics test standard.
IEC specifies IEC as the harmonics test standard.
IEEE519 specifies IEEE519 as the harmonics test standard.
REVIEEE5192022 specifies REVIEEE5192022 as the harmonics test standard.
CUSTOM specifies that there is a custom harmonics test standard.

MeasurementMeasItemHarmonicsunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HARMONICSUNits command.

Description

This command sets or queries harmonics units. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HARMONICSUNits? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HARMONICSUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HARMONICSUNits value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HARMONICSUNits {LOGARITHM|LINEAR}
- MEASUrement:MEAS<x>:HARMONICSUNits?

Info

MEAS<x> specifies the measurement number.
LOGARITHM specifies logarithmic as the harmonics units.
LINEAR specifies linear as the harmonics units.

MeasurementMeasItemHighlevel ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.configuration: The MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration command.
.l2ltol2n: The MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N command.
.lineselected: The MEASUrement:MEAS<x>:HIGHLEVel:LINESelected command.
.outl2ltol2n: The MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N command.
.outlineselected: The MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected command.
.outwiring: The MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing command.
.useglobal: The MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL command.
.wiring: The MEASUrement:MEAS<x>:HIGHLEVel:WIRing command.

configuration `property` ¶

configuration: MeasurementMeasItemHighlevelConfiguration

Return the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration command.

Description

This command sets or queries the local input and output configuration.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?

Info

MEAS<x> specifies the measurement number.
INPUT specifies the local Input or Output source settings as input.
OUTPUT specifies the local Input or Output source settings as output.

l2ltol2n `property` ¶

l2ltol2n: MeasurementMeasItemHighlevelL2ltol2n

Return the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N command.

Description

This command sets or queries local input Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?

Info

1 enables local input Line-to-Line to Line-to-Neutral Conversion.
0 disables local input Line-to-Line to Line-to-Neutral Conversion.

lineselected `property` ¶

lineselected: MeasurementMeasItemHighlevelLineselected

Return the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected command.

Description

This command sets or queries local input select lines.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected?

Info

ABCB specifies the local input select lines as ABCB.
ACBC specifies the local input select lines as ACBC.
BACA specifies the local input select lines as BACA.
AN specifies the local input select lines as AN.
BN specifies the local input select lines as BN.
CN specifies the local input select lines as CN.

outl2ltol2n `property` ¶

outl2ltol2n: MeasurementMeasItemHighlevelOutl2ltol2n

Return the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N command.

Description

This command sets or queries local output Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?

Info

1 enables local output Line-to-Line to Line-to-Neutral Conversion.
0 disables local output Line-to-Line to Line-to-Neutral Conversion.

outlineselected `property` ¶

outlineselected: MeasurementMeasItemHighlevelOutlineselected

Return the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected command.

Description

This command sets or queries local output select lines.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?

Info

XYZY specifies the local output select lines as XYZY.
XZYZ specifies the local output select lines as XZYZ.
YXZX specifies the local output select lines as YXZX.
XN specifies the local output select lines as XN.
YN specifies the local output select lines as YN.
ZN specifies the local output select lines as ZN.

outwiring `property` ¶

outwiring: MeasurementMeasItemHighlevelOutwiring

Return the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing command.

Description

This command sets or queries the local output wiring.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?

Info

MEAS<x> specifies the measurement number.
P1W2V1I1 specifies P1W2V1I1 as the local output wiring.
P3W3V2I2 specifies P3W3V2I2 as the local output wiring.
P3W3V3I3 specifies P3W3V3I3 as the local output wiring.
P3W4 specifies P3W4 as the local output wiring.
DCP1W2 specifies DCP1W2 as the local output wiring.

useglobal `property` ¶

useglobal: MeasurementMeasItemHighlevelUseglobal

Return the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL command.

Description

This command sets or queries the IMDA source settings as global or local.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL {ON|OFF|1|0}
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?

Info

MEAS<x> specifies the measurement number.
1 specifies the source settings as global.
0 specifies the source settings as local.
ON specifies the source settings as global.
OFF specifies the source settings as local.

wiring `property` ¶

wiring: MeasurementMeasItemHighlevelWiring

Return the MEASUrement:MEAS<x>:HIGHLEVel:WIRing command.

Description

This command sets or queries the local Input wiring.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:WIRing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:WIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:WIRing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing?

Info

MEAS<x> specifies the measurement number.
P1W2V1I1 specifies P1W2V1I1 as the local input wiring.
P1W3V2I2 specifies P1W3V2I2 as the local input wiring.
P3W3V2I2 specifies P3W3V2I2 as the local input wiring.
P3W3V3I3 specifies P3W3V3I3 as the local input wiring.
P3W3 specifies P3W3 as the local input wiring.
DCP1W2 specifies DCP1W2 as the local input wiring.

MeasurementMeasItemHighlevelConfiguration ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration command.

Description

This command sets or queries the local input and output configuration.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration {INPUT|OUTPUT}
- MEASUrement:MEAS<x>:HIGHLEVel:CONFIGuration?

Info

MEAS<x> specifies the measurement number.
INPUT specifies the local Input or Output source settings as input.
OUTPUT specifies the local Input or Output source settings as output.

MeasurementMeasItemHighlevelL2ltol2n ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N command.

Description

This command sets or queries local input Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:L2LTOL2N?

Info

1 enables local input Line-to-Line to Line-to-Neutral Conversion.
0 disables local input Line-to-Line to Line-to-Neutral Conversion.

MeasurementMeasItemHighlevelLineselected ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:LINESelected command.

Description

This command sets or queries local input select lines.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:LINESelected value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected {ABCB|ACBC|BACA|AN|BN|CN}
- MEASUrement:MEAS<x>:HIGHLEVel:LINESelected?

Info

ABCB specifies the local input select lines as ABCB.
ACBC specifies the local input select lines as ACBC.
BACA specifies the local input select lines as BACA.
AN specifies the local input select lines as AN.
BN specifies the local input select lines as BN.
CN specifies the local input select lines as CN.

MeasurementMeasItemHighlevelOutl2ltol2n ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N command.

Description

This command sets or queries local output Line-to-Line to Line-to-Neutral Conversion.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N {0|1}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTL2LTOL2N?

Info

1 enables local output Line-to-Line to Line-to-Neutral Conversion.
0 disables local output Line-to-Line to Line-to-Neutral Conversion.

MeasurementMeasItemHighlevelOutlineselected ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected command.

Description

This command sets or queries local output select lines.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected {XYZY|XZYZ|YXZX|XN|YN|ZN}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTLINESelected?

Info

XYZY specifies the local output select lines as XYZY.
XZYZ specifies the local output select lines as XZYZ.
YXZX specifies the local output select lines as YXZX.
XN specifies the local output select lines as XN.
YN specifies the local output select lines as YN.
ZN specifies the local output select lines as ZN.

MeasurementMeasItemHighlevelOutwiring ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing command.

Description

This command sets or queries the local output wiring.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing {P1W2V1I1|P1W3V2I2|P3W3V3I3|P3W4|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:OUTWIRing?

Info

MEAS<x> specifies the measurement number.
P1W2V1I1 specifies P1W2V1I1 as the local output wiring.
P3W3V2I2 specifies P3W3V2I2 as the local output wiring.
P3W3V3I3 specifies P3W3V3I3 as the local output wiring.
P3W4 specifies P3W4 as the local output wiring.
DCP1W2 specifies DCP1W2 as the local output wiring.

MeasurementMeasItemHighlevelUseglobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL command.

Description

This command sets or queries the IMDA source settings as global or local.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL {ON|OFF|1|0}
- MEASUrement:MEAS<x>:HIGHLEVel:USEGLOBAL?

Info

MEAS<x> specifies the measurement number.
1 specifies the source settings as global.
0 specifies the source settings as local.
ON specifies the source settings as global.
OFF specifies the source settings as local.

MeasurementMeasItemHighlevelWiring ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHLEVel:WIRing command.

Description

This command sets or queries the local Input wiring.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHLEVel:WIRing? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:WIRing? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHLEVel:WIRing value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHLEVel:WIRing {P1W2V1I1|P1W3V2I2|P3W3V2I2|P3W3V3I3|P3W3|DCP1W2}
- MEASUrement:MEAS<x>:HIGHLEVel:WIRing?

Info

MEAS<x> specifies the measurement number.
P1W2V1I1 specifies P1W2V1I1 as the local input wiring.
P1W3V2I2 specifies P1W3V2I2 as the local input wiring.
P3W3V2I2 specifies P3W3V2I2 as the local input wiring.
P3W3V3I3 specifies P3W3V3I3 as the local input wiring.
P3W3 specifies P3W3 as the local input wiring.
DCP1W2 specifies DCP1W2 as the local input wiring.

MeasurementMeasItemHighrefvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HIGHREFVoltage command.

Description

This command sets or queries the high reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HIGHREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HIGHREFVoltage <NR3>
- MEASUrement:MEAS<x>:HIGHREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference voltage value for the selected configuration.

MeasurementMeasItemHlevel ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:HLEVel command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HLEVel? query and raise an AssertionError if the returned value does not match value.

Properties

.output: The MEASUrement:MEAS<x>:HLEVel:OUTPut command tree.

output `property` ¶

output: MeasurementMeasItemHlevelOutput

Return the MEASUrement:MEAS<x>:HLEVel:OUTPut command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.uglobal: The MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal command.

MeasurementMeasItemHlevelOutput ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:HLEVel:OUTPut command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut? query and raise an AssertionError if the returned value does not match value.

Properties

.uglobal: The MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal command.

uglobal `property` ¶

uglobal: MeasurementMeasItemHlevelOutputUglobal

Return the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal command.

Description

This command turns on or off output global settings for measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal {ON|OFF}
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?

Info

ON sets the output global settings for measurement to on.
OFF sets the output global settings for measurement to off.

MeasurementMeasItemHlevelOutputUglobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal command.

Description

This command turns on or off output global settings for measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal {ON|OFF}
- MEASUrement:MEAS<x>:HLEVel:OUTPut:UGLobal?

Info

ON sets the output global settings for measurement to on.
OFF sets the output global settings for measurement to off.

MeasurementMeasItemHtorque ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HTORque command.

Description

This command sets or queries the measurement High Torque value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HTORque? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HTORque? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HTORque value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HTORque <NR1>
- MEASUrement:MEAS<x>:HTORque?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the High Torque value of the measurement in the range of 11 to 10000000.

MeasurementMeasItemHvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:HVOLtage command.

Description

This command sets or queries the measurement Torque High Voltage value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:HVOLtage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:HVOLtage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:HVOLtage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:HVOLtage <NR1>
- MEASUrement:MEAS<x>:HVOLtage?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the High Voltage value of the measurement in the range of 1 to 100.

MeasurementMeasItemIdletime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:IDLETime command.

Description

This command sets or queries the idle time for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:IDLETime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:IDLETime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:IDLETime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:IDLETime <NR3>
- MEASUrement:MEAS<x>:IDLETime?

Info

MEAS<x> specifies the measurement number.
<NR3> is the idle time.

MeasurementMeasItemInputlevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:INPUTLEVel command.

Description

Sets or queries the input trigger voltage level.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:INPUTLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:INPUTLEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:INPUTLEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:INPUTLEVel <NR2>
- MEASUrement:MEAS<x>:INPUTLEVel?

Info

MEAS<x> is the measurement number.
<NR2> is the trigger voltage, in the range of -500 V to +500 V.

MeasurementMeasItemInputpower ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:INPUTPOwer command.

Description

This command sets or queries the input power value for IEC-Class C and Class D harmonics standard.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:INPUTPOwer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:INPUTPOwer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:INPUTPOwer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:INPUTPOwer <NR3>
- MEASUrement:MEAS<x>:INPUTPOwer?

Info

MEAS<x> is the measurement number.
<NR3> specifies the input power value for class C harmonics standard.

MeasurementMeasItemJittersummary ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.dcd: The MEASUrement:MEAS<x>:JITTERSummary:DCD command.
.ddj: The MEASUrement:MEAS<x>:JITTERSummary:DDJ command.
.dj: The MEASUrement:MEAS<x>:JITTERSummary:DJ command.
.djdd: The MEASUrement:MEAS<x>:JITTERSummary:DJDD command.
.dr: The MEASUrement:MEAS<x>:JITTERSummary:DR command.
.eyewidthber: The MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER command.
.isi: The MEASUrement:MEAS<x>:JITTERSummary:ISI command.
.npj: The MEASUrement:MEAS<x>:JITTERSummary:NPJ command.
.pj: The MEASUrement:MEAS<x>:JITTERSummary:PJ command.
.pl: The MEASUrement:MEAS<x>:JITTERSummary:PL command.
.rj: The MEASUrement:MEAS<x>:JITTERSummary:RJ command.
.rjdd: The MEASUrement:MEAS<x>:JITTERSummary:RJDD command.
.tie: The MEASUrement:MEAS<x>:JITTERSummary:TIE command.
.tjber: The MEASUrement:MEAS<x>:JITTERSummary:TJBER command.

dcd `property` ¶

dcd: MeasurementMeasItemJittersummaryDcd

Return the MEASUrement:MEAS<x>:JITTERSummary:DCD command.

Description

This command sets or queries whether DCD is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DCD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DCD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DCD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DCD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DCD?

Info

MEAS<x> specifies the measurement number.
1 adds the DCD measurement as part of jitter summary.
0 do not add the DCD measurement as part of jitter summary.

ddj `property` ¶

ddj: MeasurementMeasItemJittersummaryDdj

Return the MEASUrement:MEAS<x>:JITTERSummary:DDJ command.

Description

This command sets or queries whether DDJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DDJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DDJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DDJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DDJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DDJ?

Info

MEAS<x> specifies the measurement number.
1 adds the DDJ measurement as part of jitter summary.
0 do not add the DDJ measurement as part of jitter summary.

dj `property` ¶

dj: MeasurementMeasItemJittersummaryDj

Return the MEASUrement:MEAS<x>:JITTERSummary:DJ command.

Description

This command Sets or queries whether DJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJ?

Info

MEAS<x> specifies the measurement number.
1 adds the DJ measurement as part of jitter summary.
0 do not add the DJ measurement as part of jitter summary.

djdd `property` ¶

djdd: MeasurementMeasItemJittersummaryDjdd

Return the MEASUrement:MEAS<x>:JITTERSummary:DJDD command.

Description

This command sets or queries whether DJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DJDD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJDD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJDD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJDD?

Info

MEAS<x> specifies the measurement number.
1 add the DJDD measurement as part of jitter summary.
0 do not add the DJDD measurement as part of jitter summary.

dr `property` ¶

dr: MeasurementMeasItemJittersummaryDr

Return the MEASUrement:MEAS<x>:JITTERSummary:DR command.

Description

This command Sets or queries whether DR is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DR? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DR? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DR value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DR {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DR?

Info

MEAS<x> specifies the measurement number.
1 adds the DR measurement as part of jitter summary.
0 do not add the DR measurement as part of jitter summary.

eyewidthber `property` ¶

eyewidthber: MeasurementMeasItemJittersummaryEyewidthber

Return the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER command.

Description

This command sets or queries whether EyeWidth@BER is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?

Info

MEAS<x> specifies the measurement number.
1 add the EyeWidth@BER measurement as part of jitter summary.
0 do not add the EyeWidth@BER measurement as part of jitter summary.

isi `property` ¶

isi: MeasurementMeasItemJittersummaryIsi

Return the MEASUrement:MEAS<x>:JITTERSummary:ISI command.

Description

This command Sets or queries whether ISI is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:ISI? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:ISI? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:ISI value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:ISI {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:ISI?

Info

MEAS<x> specifies the measurement number.
1 adds the ISI measurement as part of jitter summary.
0 do not add the ISI measurement as part of jitter summary.

npj `property` ¶

npj: MeasurementMeasItemJittersummaryNpj

Return the MEASUrement:MEAS<x>:JITTERSummary:NPJ command.

Description

This command sets or queries whether NPJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:NPJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:NPJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:NPJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:NPJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:NPJ?

Info

MEAS<x> specifies the measurement number.
1 add the NPJ measurement as part of jitter summary.
0 do not add the NPJ measurement as part of jitter summary.

pj `property` ¶

pj: MeasurementMeasItemJittersummaryPj

Return the MEASUrement:MEAS<x>:JITTERSummary:PJ command.

Description

This command sets or queries whether PJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:PJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:PJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PJ?

Info

MEAS<x> specifies the measurement number.
1 add the PJ measurement as part of jitter summary.
0 do not add the PJ measurement as part of jitter summary.

pl `property` ¶

pl: MeasurementMeasItemJittersummaryPl

Return the MEASUrement:MEAS<x>:JITTERSummary:PL command.

Description

This command Sets or queries whether PL is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:PL? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PL? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PL value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:PL {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PL?

Info

MEAS<x> specifies the measurement number.
1 adds the PL measurement as part of jitter summary.
0 do not add the PL measurement as part of jitter summary.

rj `property` ¶

rj: MeasurementMeasItemJittersummaryRj

Return the MEASUrement:MEAS<x>:JITTERSummary:RJ command.

Description

This command Sets or queries whether RJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:RJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:RJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJ?

Info

MEAS<x> specifies the measurement number.
1 adds the RJ measurement as part of jitter summary.
0 do not add the RJ measurement as part of jitter summary.

rjdd `property` ¶

rjdd: MeasurementMeasItemJittersummaryRjdd

Return the MEASUrement:MEAS<x>:JITTERSummary:RJDD command.

Description

This command sets or queries whether RJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:RJDD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJDD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJDD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:RJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJDD?

Info

MEAS<x> specifies the measurement number.
1 add the RJ-dd measurement as part of jitter summary.
0 do not add the RJ-dd measurement as part of jitter summary.

tie `property` ¶

tie: MeasurementMeasItemJittersummaryTie

Return the MEASUrement:MEAS<x>:JITTERSummary:TIE command.

Description

This command sets or queries whether TIE is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:TIE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TIE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TIE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:TIE {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TIE?

Info

MEAS<x> specifies the measurement number.
1 add the TIE measurement as part of jitter summary.
0 do not add the TIE measurement as part of jitter summary.

tjber `property` ¶

tjber: MeasurementMeasItemJittersummaryTjber

Return the MEASUrement:MEAS<x>:JITTERSummary:TJBER command.

Description

This command sets or queries whether TJ@BER is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:TJBER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TJBER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TJBER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:TJBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TJBER?

Info

MEAS<x> specifies the measurement number.
1 add the TJ@BER measurement as part of jitter summary.
0 do not add the TJ@BER measurement as part of jitter summary.

MeasurementMeasItemJittersummaryDcd ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:DCD command.

Description

This command sets or queries whether DCD is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DCD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DCD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DCD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DCD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DCD?

Info

MEAS<x> specifies the measurement number.
1 adds the DCD measurement as part of jitter summary.
0 do not add the DCD measurement as part of jitter summary.

MeasurementMeasItemJittersummaryDdj ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:DDJ command.

Description

This command sets or queries whether DDJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DDJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DDJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DDJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DDJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DDJ?

Info

MEAS<x> specifies the measurement number.
1 adds the DDJ measurement as part of jitter summary.
0 do not add the DDJ measurement as part of jitter summary.

MeasurementMeasItemJittersummaryDj ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:DJ command.

Description

This command Sets or queries whether DJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJ?

Info

MEAS<x> specifies the measurement number.
1 adds the DJ measurement as part of jitter summary.
0 do not add the DJ measurement as part of jitter summary.

MeasurementMeasItemJittersummaryDjdd ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:DJDD command.

Description

This command sets or queries whether DJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DJDD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJDD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DJDD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DJDD?

Info

MEAS<x> specifies the measurement number.
1 add the DJDD measurement as part of jitter summary.
0 do not add the DJDD measurement as part of jitter summary.

MeasurementMeasItemJittersummaryDr ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:DR command.

Description

This command Sets or queries whether DR is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:DR? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DR? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:DR value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:DR {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:DR?

Info

MEAS<x> specifies the measurement number.
1 adds the DR measurement as part of jitter summary.
0 do not add the DR measurement as part of jitter summary.

MeasurementMeasItemJittersummaryEyewidthber ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER command.

Description

This command sets or queries whether EyeWidth@BER is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:EYEWIDTHBER?

Info

MEAS<x> specifies the measurement number.
1 add the EyeWidth@BER measurement as part of jitter summary.
0 do not add the EyeWidth@BER measurement as part of jitter summary.

MeasurementMeasItemJittersummaryIsi ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:ISI command.

Description

This command Sets or queries whether ISI is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:ISI? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:ISI? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:ISI value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:ISI {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:ISI?

Info

MEAS<x> specifies the measurement number.
1 adds the ISI measurement as part of jitter summary.
0 do not add the ISI measurement as part of jitter summary.

MeasurementMeasItemJittersummaryNpj ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:NPJ command.

Description

This command sets or queries whether NPJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:NPJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:NPJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:NPJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:NPJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:NPJ?

Info

MEAS<x> specifies the measurement number.
1 add the NPJ measurement as part of jitter summary.
0 do not add the NPJ measurement as part of jitter summary.

MeasurementMeasItemJittersummaryPj ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:PJ command.

Description

This command sets or queries whether PJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:PJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:PJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PJ?

Info

MEAS<x> specifies the measurement number.
1 add the PJ measurement as part of jitter summary.
0 do not add the PJ measurement as part of jitter summary.

MeasurementMeasItemJittersummaryPl ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:PL command.

Description

This command Sets or queries whether PL is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:PL? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PL? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:PL value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:PL {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:PL?

Info

MEAS<x> specifies the measurement number.
1 adds the PL measurement as part of jitter summary.
0 do not add the PL measurement as part of jitter summary.

MeasurementMeasItemJittersummaryRj ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:RJ command.

Description

This command Sets or queries whether RJ is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:RJ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:RJ {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJ?

Info

MEAS<x> specifies the measurement number.
1 adds the RJ measurement as part of jitter summary.
0 do not add the RJ measurement as part of jitter summary.

MeasurementMeasItemJittersummaryRjdd ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:RJDD command.

Description

This command sets or queries whether RJ-dd is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:RJDD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJDD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:RJDD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:RJDD {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:RJDD?

Info

MEAS<x> specifies the measurement number.
1 add the RJ-dd measurement as part of jitter summary.
0 do not add the RJ-dd measurement as part of jitter summary.

MeasurementMeasItemJittersummaryTie ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:TIE command.

Description

This command sets or queries whether TIE is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:TIE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TIE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TIE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:TIE {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TIE?

Info

MEAS<x> specifies the measurement number.
1 add the TIE measurement as part of jitter summary.
0 do not add the TIE measurement as part of jitter summary.

MeasurementMeasItemJittersummaryTjber ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:JITTERSummary:TJBER command.

Description

This command sets or queries whether TJ@BER is included in the jitter summary for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:JITTERSummary:TJBER? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TJBER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:JITTERSummary:TJBER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:JITTERSummary:TJBER {0|1}
- MEASUrement:MEAS<x>:JITTERSummary:TJBER?

Info

MEAS<x> specifies the measurement number.
1 add the TJ@BER measurement as part of jitter summary.
0 do not add the TJ@BER measurement as part of jitter summary.

MeasurementMeasItemLabel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LABel command.

Description

This command sets or queries the label for the measurement. As the label can contain non 7-bit ASCII text, it is stored in Percent Encoding format. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LABel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LABel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LABel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LABel <QString>
- MEASUrement:MEAS<x>:LABel?

Info

MEAS<x> specifies the measurement number.
<QString> is the measurement label.

MeasurementMeasItemLineselected ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LINESelected command.

Description

This command sets or queries selected lines for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LINESelected? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LINESelected? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LINESelected value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LINESelected {ABCB|ACBC|BACA|XYZY|XZYZ|YXZX}
- MEASUrement:MEAS<x>:LINESelected?

Info

MEAS<x> specifies the measurement number.
ABCB specifies the selected lines as ABCB.
ACBC specifies the selected lines as ACBC.
BACA specifies the selected lines as BACA.
XYZY specifies the selected lines as XYZY.
XZYZ specifies the selected lines as XZYZ.
YXZX specifies the selected lines as YXZX.

MeasurementMeasItemLowrefvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LOWREFVoltage command.

Description

This command sets or queries the low reference voltage value for the ‘time outside level’ measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LOWREFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LOWREFVoltage <NR3>
- MEASUrement:MEAS<x>:LOWREFVoltage?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference voltage value for the selected configuration.

MeasurementMeasItemLtorque ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LTORque command.

Description

This command sets or queries the measurement Low Torque value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LTORque? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LTORque? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LTORque value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LTORque <NR1>
- MEASUrement:MEAS<x>:LTORque?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the Low Torque value of the measurement in the range of 0 to 10000000.

MeasurementMeasItemLtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LTYPe command.

Description

This command sets or returns the value for the level type as auto or custom. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LTYPe {AUTO|CUSTom}
- MEASUrement:MEAS<x>:LTYPe?

Info

AUTO specifies the value for the level type as auto.
CUSTom specifies the value for the level type as custom.

MeasurementMeasItemLunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LUNITs command.

Description

This command sets or returns the value for the level units as percentage or absolute. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LUNITs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LUNITs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LUNITs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LUNITs {PERCent|ABSolute}
- MEASUrement:MEAS<x>:LUNITs?

Info

PERCent specifies the value for the level units as percent.
ABSolute specifies the value for the level units as absolute.

MeasurementMeasItemLvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:LVOLtage command.

Description

This command sets or queries the measurement Torque Low Voltage value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:LVOLtage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:LVOLtage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:LVOLtage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:LVOLtage <NR1>
- MEASUrement:MEAS<x>:LVOLtage?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the Low Voltage value of the measurement in the range of -100 to 100.

MeasurementMeasItemMatime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MATime command.

Description

This command sets or returns the maximum acquisition time for WBG measurement. This should be set only if AFG is not AFG31000.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MATime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MATime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MATime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MATime <NR3>
- MEASUrement:MEAS<x>:MATime?

Info

MATime specifies the maximum acquisition time for WBG measurement.

MeasurementMeasItemMaxcurrent ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MAXCUrrent command.

Description

This command sets or returns the maximum current. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXCUrrent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXCUrrent? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXCUrrent value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXCUrrent <NR3>
- MEASUrement:MEAS<x>:MAXCUrrent?

Info

<NR3> specifies the maximum current.

MeasurementMeasItemMaxcycle ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MAXCycle command.

Description

This command sets or queries the maximum cycle value for the DDRTERRN and DDRTERRMN measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXCycle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXCycle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXCycle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXCycle <NR1>
- MEASUrement:MEAS<x>:MAXCycle?

Info

MEAS<x> specifies the measurement number.
<NR1> is the maximum cycle range limit value in the range or 2 to 50.

MeasurementMeasItemMaxg1voltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MAXG1Voltage command.

Description

This command sets or returns the maximum gate voltage 1 or 2 value for Tdt measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXG1Voltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXG1Voltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXG1Voltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXG1Voltage <NR3>
- MEASUrement:MEAS<x>:MAXG1Voltage?

Info

<NR3> specifies the maximum gate voltage.

MeasurementMeasItemMaxg2voltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MAXG2Voltage command.

Description

This command sets or returns the maximum gate voltage 1 or 2 value for Tdt measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXG2Voltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXG2Voltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXG2Voltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXG2Voltage <NR3>
- MEASUrement:MEAS<x>:MAXG2Voltage?

Info

<NR3> specifies the maximum gate voltage.

MeasurementMeasItemMaxgvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MAXGVoltage command.

Description

This command sets or returns the maximum gate voltage. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXGVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXGVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXGVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXGVoltage <NR3>
- MEASUrement:MEAS<x>:MAXGVoltage?

Info

<NR3> specifies the maximum gate voltage.

MeasurementMeasItemMaxvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MAXVoltage command.

Description

Sets or queries the maximum input voltage. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MAXVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MAXVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MAXVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MAXVoltage <NR2>
- MEASUrement:MEAS<x>:MAXVoltage?

Info

<NR2> is the maximum input voltage, in the range of -61 V to +61 V.

MeasurementMeasItemMeasrange ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:MEASRange command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.global: The MEASUrement:MEAS<x>:MEASRange:GLOBal command.
.max: The MEASUrement:MEAS<x>:MEASRange:MAX command.
.min: The MEASUrement:MEAS<x>:MEASRange:MIN command.
.state: The MEASUrement:MEAS<x>:MEASRange:STATE command.

global_ `property` ¶

global_: MeasurementMeasItemMeasrangeGlobal

Return the MEASUrement:MEAS<x>:MEASRange:GLOBal command.

Description

This command sets or queries the range settings global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies that range settings can be set independently for each individual measurement.
ON applies global measurement range settings to all the measurements’ range settings.
0 specifies that range settings can be set independently for each individual measurement.
1 applies global measurement range settings to all the measurements’ range settings.

max `property` ¶

max: MeasurementMeasItemMeasrangeMax

Return the MEASUrement:MEAS<x>:MEASRange:MAX command.

Description

This command sets or queries the range maximum value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:MAX? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:MAX? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:MAX value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:MAX <NR3>
- MEASUrement:MEAS<x>:MEASRange:MAX?

Info

MEAS<x> specifies the measurement number.
<NR3> is the maximum measurement range limit value.

min `property` ¶

min: MeasurementMeasItemMeasrangeMin

Return the MEASUrement:MEAS<x>:MEASRange:MIN command.

Description

This command sets or queries the range minimum value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:MIN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:MIN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:MIN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:MIN <NR3>
- MEASUrement:MEAS<x>:MEASRange:MIN?

Info

MEAS<x> specifies the measurement number.
<NR3> is the minimum measurement range limit value.

state `property` ¶

state: MeasurementMeasItemMeasrangeState

Return the MEASUrement:MEAS<x>:MEASRange:STATE command.

Description

This command sets or queries the range state for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:STATE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:STATE?

Info

MEAS<x> specifies the measurement number.
OFF turns off the measurement range limits.
ON turns on the measurement range limits.
0 turns off the measurement range limits.
1 turns on the measurement range limits.

MeasurementMeasItemMeasrangeGlobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MEASRange:GLOBal command.

Description

This command sets or queries the range settings global flag for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies that range settings can be set independently for each individual measurement.
ON applies global measurement range settings to all the measurements’ range settings.
0 specifies that range settings can be set independently for each individual measurement.
1 applies global measurement range settings to all the measurements’ range settings.

MeasurementMeasItemMeasrangeMax ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MEASRange:MAX command.

Description

This command sets or queries the range maximum value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:MAX? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:MAX? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:MAX value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:MAX <NR3>
- MEASUrement:MEAS<x>:MEASRange:MAX?

Info

MEAS<x> specifies the measurement number.
<NR3> is the maximum measurement range limit value.

MeasurementMeasItemMeasrangeMin ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MEASRange:MIN command.

Description

This command sets or queries the range minimum value for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:MIN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:MIN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:MIN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:MIN <NR3>
- MEASUrement:MEAS<x>:MEASRange:MIN?

Info

MEAS<x> specifies the measurement number.
<NR3> is the minimum measurement range limit value.

MeasurementMeasItemMeasrangeState ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MEASRange:STATE command.

Description

This command sets or queries the range state for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MEASRange:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MEASRange:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MEASRange:STATE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MEASRange:STATE?

Info

MEAS<x> specifies the measurement number.
OFF turns off the measurement range limits.
ON turns on the measurement range limits.
0 turns off the measurement range limits.
1 turns on the measurement range limits.

MeasurementMeasItemMech ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:MECH command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH? query and raise an AssertionError if the returned value does not match value.

Properties

.eindexz: The MEASUrement:MEAS<x>:MECH:EINDexz command.
.gratio: The MEASUrement:MEAS<x>:MECH:GRATio command.
.munits: The MEASUrement:MEAS<x>:MECH:MUNits command.
.ppairs: The MEASUrement:MEAS<x>:MECH:PPAirs command.
.pprotation: The MEASUrement:MEAS<x>:MECH:PPRotation command.
.stype: The MEASUrement:MEAS<x>:MECH:STYPe command.

eindexz `property` ¶

eindexz: MeasurementMeasItemMechEindexz

Return the MEASUrement:MEAS<x>:MECH:EINDexz command.

Description

This command sets or queries the specified mechanical Index Z source. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:EINDexz? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:EINDexz? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:EINDexz value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MECH:EINDexz?

Info

ON specifies the Index Z check box state as enabled.
OFF specifies the Index Z check box state as disabled.
1 specifies the Index Z check box state as enabled.
0 specifies the Index Z check box state as disabled.

gratio `property` ¶

gratio: MeasurementMeasItemMechGratio

Return the MEASUrement:MEAS<x>:MECH:GRATio command.

Description

This command sets or queries the gear ratio for the specific measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:GRATio? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:GRATio? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:GRATio value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:GRATio <NR3>
- MEASUrement:MEAS<x>:MECH:GRATio?

Info

<NR3> defines the gear ratio value for specified measurement. The minimum to maximum range is 0.001-1000.

munits `property` ¶

munits: MeasurementMeasItemMechMunits

Return the MEASUrement:MEAS<x>:MECH:MUNits command.

Description

This command sets or queries the specified mechanical measurement results units. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:MUNits? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:MUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:MUNits value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MEAS<x>:MECH:MUNits?

Info

NM defines the results units of the measurement as NM.
OZINCH defines the results units of the measurement as OZINCH.
FTLB defines the results units of the measurement as FTLB.
INCHLB defines the results units of the measurement as INCHLB.
DEGREES defines the results units of the measurement as DEGREES.
RADIANS defines the results units of the measurement as RADIANS.

ppairs `property` ¶

ppairs: MeasurementMeasItemMechPpairs

Return the MEASUrement:MEAS<x>:MECH:PPAirs command.

Description

This command sets or queries the number of pole pairs for the specific measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:PPAirs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:PPAirs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:PPAirs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:PPAirs <NR1>
- MEASUrement:MEAS<x>:MECH:PPAirs?

Info

<NR1> defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.

pprotation `property` ¶

pprotation: MeasurementMeasItemMechPprotation

Return the MEASUrement:MEAS<x>:MECH:PPRotation command.

Description

This command sets or queries the specified pulses per rotation of the measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:PPRotation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:PPRotation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:PPRotation value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:PPRotation <NR1>
- MEASUrement:MEAS<x>:MECH:PPRotation?

Info

MEAS<x> specifies the measurement number.
<NR1> defines the pulses per rotation of the measurement in the range of 1 to 10000.

stype `property` ¶

stype: MeasurementMeasItemMechStype

Return the MEASUrement:MEAS<x>:MECH:STYPe command.

Description

This command sets or queries the local measurement sensor type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:STYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:STYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:STYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:STYPe {HSENSOR|QEI|RESOLVER}
- MEASUrement:MEAS<x>:MECH:STYPe?

Info

MEAS<x> specifies the measurement number.
HSENSOR specifies the sensor type as HSENSOR.
QEI specifies the sensor type as QEI.
RESOLVER specifies the sensor type as RESOLVER.

MeasurementMeasItemMechEindexz ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MECH:EINDexz command.

Description

This command sets or queries the specified mechanical Index Z source. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:EINDexz? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:EINDexz? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:EINDexz value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MEAS<x>:MECH:EINDexz?

Info

ON specifies the Index Z check box state as enabled.
OFF specifies the Index Z check box state as disabled.
1 specifies the Index Z check box state as enabled.
0 specifies the Index Z check box state as disabled.

MeasurementMeasItemMechGratio ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MECH:GRATio command.

Description

This command sets or queries the gear ratio for the specific measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:GRATio? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:GRATio? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:GRATio value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:GRATio <NR3>
- MEASUrement:MEAS<x>:MECH:GRATio?

Info

<NR3> defines the gear ratio value for specified measurement. The minimum to maximum range is 0.001-1000.

MeasurementMeasItemMechMunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MECH:MUNits command.

Description

This command sets or queries the specified mechanical measurement results units. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:MUNits? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:MUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:MUNits value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MEAS<x>:MECH:MUNits?

Info

NM defines the results units of the measurement as NM.
OZINCH defines the results units of the measurement as OZINCH.
FTLB defines the results units of the measurement as FTLB.
INCHLB defines the results units of the measurement as INCHLB.
DEGREES defines the results units of the measurement as DEGREES.
RADIANS defines the results units of the measurement as RADIANS.

MeasurementMeasItemMechPpairs ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MECH:PPAirs command.

Description

This command sets or queries the number of pole pairs for the specific measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:PPAirs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:PPAirs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:PPAirs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:PPAirs <NR1>
- MEASUrement:MEAS<x>:MECH:PPAirs?

Info

<NR1> defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.

MeasurementMeasItemMechPprotation ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MECH:PPRotation command.

Description

This command sets or queries the specified pulses per rotation of the measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:PPRotation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:PPRotation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:PPRotation value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:PPRotation <NR1>
- MEASUrement:MEAS<x>:MECH:PPRotation?

Info

MEAS<x> specifies the measurement number.
<NR1> defines the pulses per rotation of the measurement in the range of 1 to 10000.

MeasurementMeasItemMechStype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MECH:STYPe command.

Description

This command sets or queries the local measurement sensor type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MECH:STYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MECH:STYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MECH:STYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MECH:STYPe {HSENSOR|QEI|RESOLVER}
- MEASUrement:MEAS<x>:MECH:STYPe?

Info

MEAS<x> specifies the measurement number.
HSENSOR specifies the sensor type as HSENSOR.
QEI specifies the sensor type as QEI.
RESOLVER specifies the sensor type as RESOLVER.

MeasurementMeasItemMincycle ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:MINCycle command.

Description

This command sets or queries the minimum cycle value for the DDRTERRN and DDRTERRMN measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:MINCycle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:MINCycle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:MINCycle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:MINCycle <NR1>
- MEASUrement:MEAS<x>:MINCycle?

Info

MEAS<x> specifies the measurement number.
<NR1> is the minimum cycle range limit value in the range or 2 to 50.

MeasurementMeasItemNvalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:NVALUe command.

Description

Sets or queries the number of unit intervals used for the Base Measurement Type of NUnitInterval.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:NVALUe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:NVALUe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:NVALUe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:NVALUe <N>
- MEASUrement:MEAS<x>:NVALUe?

Info

MEAS<x> specifies the measurement number.
<N> specifies the number of unit intervals.

MeasurementMeasItemObwmethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OBWMethod command.

Description

This command sets or queries the RF measurement Occupied Bandwidth method type. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OBWMethod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OBWMethod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OBWMethod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OBWMethod {percOfPwr|dBDown}
- MEASUrement:MEAS<x>:OBWMethod?

Info

percOfPwr specifies the method type as percentage of power. This is the default value.
dBDown specifies the method type as dB down.

MeasurementMeasItemOddeven ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:ODDEVen command.

Description

This command sets or queries harmonics oddeven.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:ODDEVen? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:ODDEVen? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:ODDEVen value command.

SCPI Syntax

- MEASUrement:MEAS<x>:ODDEVen {ALL|EVEN|ODD}
- MEASUrement:MEAS<x>:ODDEVen?

Info

MEAS<x> specifies the measurement number.
ALL displays all the results.
EVEN displays the even results.
ODD displays the odd results.

MeasurementMeasItemOfilters ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:OFILters command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.lowpass: The MEASUrement:MEAS<x>:OFILters:LOWPass command tree.

lowpass `property` ¶

lowpass: MeasurementMeasItemOfiltersLowpass

Return the MEASUrement:MEAS<x>:OFILters:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.freq: The MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC command.

MeasurementMeasItemOfiltersLowpass ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:OFILters:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.freq: The MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC command.

freq `property` ¶

freq: MeasurementMeasItemOfiltersLowpassFreq

Return the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ command.

Description

This command sets or returns the cut-off frequency value for a measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the cut-off frequency value for a measurement.

spec `property` ¶

spec: MeasurementMeasItemOfiltersLowpassSpec

Return the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC command.

Description

This command sets or returns low pass filter specification for a measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies the low pass filter specification as none.
FIRST specifies the low pass filter specification set to 1st Order for the measurement.
SECOND specifies the low pass filter specification set to 2nd Order for the measurement.
THIRD specifies the low pass filter specification set to 3rd Order for the measurement.

MeasurementMeasItemOfiltersLowpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ command.

Description

This command sets or returns the cut-off frequency value for a measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ <NR3>
- MEASUrement:MEAS<x>:OFILters:LOWPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the cut-off frequency value for a measurement.

MeasurementMeasItemOfiltersLowpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC command.

Description

This command sets or returns low pass filter specification for a measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OFILters:LOWPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies the low pass filter specification as none.
FIRST specifies the low pass filter specification set to 1st Order for the measurement.
SECOND specifies the low pass filter specification set to 2nd Order for the measurement.
THIRD specifies the low pass filter specification set to 3rd Order for the measurement.

MeasurementMeasItemOsangle ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OSANgle command.

Description

This command sets or queries the specified measurement Offset angle.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OSANgle? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OSANgle? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OSANgle value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OSANgle <NR1>
- MEASUrement:MEAS<x>:OSANgle?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the offset angle of the measurement in the range or -360 to 360.

MeasurementMeasItemOutedgequalifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OUTEDGEQUALifier command.

Description

This command sets or queries local output edge qualifier source.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTEDGEQUALifier? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTEDGEQUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTEDGEQUALifier value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTEDGEQUALifier {CH<x>|MATH<x>|REF<x>}
- MEASUrement:MEAS<x>:OUTEDGEQUALifier?

Info

MEAS<x> specifies the measurement number.
CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementMeasItemOutfilters ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:OUTFILTers command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.lowpass: The MEASUrement:MEAS<x>:OUTFILTers:LOWPass command tree.

lowpass `property` ¶

lowpass: MeasurementMeasItemOutfiltersLowpass

Return the MEASUrement:MEAS<x>:OUTFILTers:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.freq: The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC command.

MeasurementMeasItemOutfiltersLowpass ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:OUTFILTers:LOWPass command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.freq: The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ command.
.spec: The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC command.

freq `property` ¶

freq: MeasurementMeasItemOutfiltersLowpassFreq

Return the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ command.

Description

This command sets or queries the measurement output low pass filter frequency cutoff frequency on the scope.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ <NR2>
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR2> specifies the values for the output filter cutoff frequency. The argument range is 20 Hz to 10e6 Hz.

spec `property` ¶

spec: MeasurementMeasItemOutfiltersLowpassSpec

Return the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC command.

Description

This command sets or queries the measurement output low pass filter specification filter order on the scope. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies the filter order none.
FIRST specifies the filter order first.
SECOND specifies the filter order second.
THIRD specifies the filter order third.

MeasurementMeasItemOutfiltersLowpassFreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ command.

Description

This command sets or queries the measurement output low pass filter frequency cutoff frequency on the scope.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ <NR2>
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:FREQ?

Info

MEAS<x> specifies the measurement number.
<NR2> specifies the values for the output filter cutoff frequency. The argument range is 20 Hz to 10e6 Hz.

MeasurementMeasItemOutfiltersLowpassSpec ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC command.

Description

This command sets or queries the measurement output low pass filter specification filter order on the scope. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- MEASUrement:MEAS<x>:OUTFILTers:LOWPass:SPEC?

Info

MEAS<x> specifies the measurement number.
NONE specifies the filter order none.
FIRST specifies the filter order first.
SECOND specifies the filter order second.
THIRD specifies the filter order third.

MeasurementMeasItemOutputvoltageItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:OUTPUT<x>VOLTage command.

Description

Sets or queries the voltage level for the specified output voltage source n.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:OUTPUT<x>VOLTage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:OUTPUT<x>VOLTage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:OUTPUT<x>VOLTage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:OUTPUT<x>VOLTage <NR2>
- MEASUrement:MEAS<x>:OUTPUT<x>VOLTage?

Info

MEAS<x> specifies the measurement number.
<NR2> is the output voltage for source n, in the range of -61 V to +61 V.

MeasurementMeasItemPassfailenabled ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILENabled command.

Description

This command returns or sets the pass/fail test enable status. If enabled, this will turn on pass fail testing for the specified measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILENabled value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILENabled <NR1>
- MEASUrement:MEAS<x>:PASSFAILENabled?

Info

<NR1> enables or disables pass fail testing for the specified measurement. A value of 1 enables and a value of 0 disables.

MeasurementMeasItemPassfailhighlimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILHIGHlimit command.

Description

This command returns or sets the high limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILHIGHlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILHIGHlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILHIGHlimit?

Info

<NR2> sets the high limit for a measurement test. The high limit is a number which a measurement result will be tested against.

MeasurementMeasItemPassfaillimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILLIMit command.

Description

This command returns or sets the limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLIMit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLIMit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLIMit?

Info

<NR2> sets the limit for a measurement test. The limit is a number which a measurement result will be tested against.

MeasurementMeasItemPassfaillowlimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILLOWlimit command.

Description

This command returns or sets the low limit for a measurement test. Used as the test value when the ‘fail when’ criteria is set to ‘less than’ or ‘greater than’. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILLOWlimit value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILLOWlimit <NR2>
- MEASUrement:MEAS<x>:PASSFAILLOWlimit?

Info

<NR2> sets the low limit for a measurement test. The limit is a number which a measurement result will be tested against.

MeasurementMeasItemPassfailmargin ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILMARgin command.

Description

This command returns or sets the allowed margin for limit comparisons for all pass/fail checks. This is given as a percentage with a default value of 0.05 representing 5%. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILMARgin value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILMARgin <NR2>
- MEASUrement:MEAS<x>:PASSFAILMARgin?

Info

<NR2> sets the allowed margin for limit comparisons for all pass/fail checks. The margin as a percentage of the limit.

MeasurementMeasItemPassfailwhen ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PASSFAILWHEN command.

Description

This command sets or returns the condition on which a measurement test fails. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PASSFAILWHEN value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PASSFAILWHEN {LESSthan|GREATERthan|Equals|NOTEQuals|INSIDErange|OUTSIDErange}
- MEASUrement:MEAS<x>:PASSFAILWHEN?

Info

LESSthan sets the condition for measurement test failure as less than the given limit. This is the default value.
GREATERthan sets the condition for measurement test failure as greater than the given limit.
Equals sets the condition for measurement test failure as equals the given limit.
NOTEQuals sets the condition for measurement test failure as not equal to the given limit.
INSIDErange sets the condition for measurement test failure as inside the limit range.
OUTSIDErange sets the condition for measurement test failure as outside the limit range.

MeasurementMeasItemPatterndetection ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PATTERNDETECTION command.

Description

This command sets or queries the pattern detection type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PATTERNDETECTION? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PATTERNDETECTION? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PATTERNDETECTION value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PATTERNDETECTION {AUTO|MANUAL}
- MEASUrement:MEAS<x>:PATTERNDETECTION?

Info

MEAS<x> specifies the measurement number.
AUTO automatically detects the pattern.
MANUAL requires manually detecting the pattern.

MeasurementMeasItemPatternlength ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PATTERNLENgth command.

Description

This command sets or queries the pattern length for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PATTERNLENgth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PATTERNLENgth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PATTERNLENgth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PATTERNLENgth <NR3>
- MEASUrement:MEAS<x>:PATTERNLENgth?

Info

MEAS<x> specifies the measurement number.
<NR3> is the pattern length.

MeasurementMeasItemPatterntype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PATTERNTYPe command.

Description

This command sets or queries the pattern type for the measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PATTERNTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PATTERNTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PATTERNTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PATTERNTYPe {REPeating|ARBitrary}
- MEASUrement:MEAS<x>:PATTERNTYPe?

Info

MEAS<x> specifies the measurement number.
REPeating specifies a repeating pattern.
ARBitrary specifies an arbitrary pattern.

MeasurementMeasItemPcount ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PCOUNt command.

Description

This command sets or returns number of pulses. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PCOUNt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PCOUNt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PCOUNt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PCOUNt <NR3>
- MEASUrement:MEAS<x>:PCOUNt?

Info

MEAS<x> specifies the measurement number.
<NR3> is the number of pulses.

MeasurementMeasItemPerfreq ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:PERFREQ command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.edge: The MEASUrement:MEAS<x>:PERFREQ:EDGE command.

edge `property` ¶

edge: MeasurementMeasItemPerfreqEdge

Return the MEASUrement:MEAS<x>:PERFREQ:EDGE command.

Description

This command sets or queries the edge type of a Period/Frequency measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
- MEASUrement:MEAS<x>:PERFREQ:EDGE?

Info

MEAS<x> specifies the measurement number.
FIRST computes the measurement between Rising edges if the first edge is Rising. Computes the measurement between Falling edges if the first edge is Falling.
RISE computes the measurement between Rising edges.
FALL computes the measurement between Falling edges.

MeasurementMeasItemPerfreqEdge ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PERFREQ:EDGE command.

Description

This command sets or queries the edge type of a Period/Frequency measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PERFREQ:EDGE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PERFREQ:EDGE {FIRST|RISE|FALL}
- MEASUrement:MEAS<x>:PERFREQ:EDGE?

Info

MEAS<x> specifies the measurement number.
FIRST computes the measurement between Rising edges if the first edge is Rising. Computes the measurement between Falling edges if the first edge is Falling.
RISE computes the measurement between Rising edges.
FALL computes the measurement between Falling edges.

MeasurementMeasItemPfrequency ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PFREquency command.

Description

This command sets or returns the PJ max frequency value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PFREquency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PFREquency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PFREquency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PFREquency <NR3>
- MEASUrement:MEAS<x>:PFREquency?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of PJ max frequency for PSIJ measurement.

MeasurementMeasItemPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:POLarity command.

Description

This command sets or queries the polarity for the measurement when the measurement type is burst width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POLarity? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POLarity value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POLarity {NORMal|INVerted}
- MEASUrement:MEAS<x>:POLarity?

Info

MEAS<x> specifies the measurement number.
NORMal specifies normal polarity.
INVerted specifies inverted polarity.

MeasurementMeasItemPopower ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:POPower command.

Description

This command sets or queries the Percentage Power to be measured for the Occupied Bandwidth measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPower? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPower? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPower value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPower <NR3>
- MEASUrement:MEAS<x>:POPower?

Info

<NR3> sets the Percentage Power value. The default value is 99.9 and the valid range is 60.0 to 99.9.

MeasurementMeasItemPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:POPUlation command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.global: The MEASUrement:MEAS<x>:POPUlation:GLOBal command.
.limit: The MEASUrement:MEAS<x>:POPUlation:LIMIT command tree.

global_ `property` ¶

global_: MeasurementMeasItemPopulationGlobal

Return the MEASUrement:MEAS<x>:POPUlation:GLOBal command.

Description

This command sets or queries the population settings global flag. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPUlation:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPUlation:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies that population settings can be changed independently for each individual measurement.
ON applies the global population settings to all the measurements’ population settings.
0 specifies that population settings can be changed independently for each individual measurement.
1 applies the global population settings to all the measurements’ population settings.

limit `property` ¶

limit: MeasurementMeasItemPopulationLimit

Return the MEASUrement:MEAS<x>:POPUlation:LIMIT command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.state: The MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE command.
.value: The MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue command.

MeasurementMeasItemPopulationGlobal ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:POPUlation:GLOBal command.

Description

This command sets or queries the population settings global flag. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:GLOBal? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:GLOBal? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPUlation:GLOBal value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPUlation:GLOBal {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:GLOBal?

Info

MEAS<x> specifies the measurement number.
OFF specifies that population settings can be changed independently for each individual measurement.
ON applies the global population settings to all the measurements’ population settings.
0 specifies that population settings can be changed independently for each individual measurement.
1 applies the global population settings to all the measurements’ population settings.

MeasurementMeasItemPopulationLimit ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:POPUlation:LIMIT command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.state: The MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE command.
.value: The MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue command.

state `property` ¶

state: MeasurementMeasItemPopulationLimitState

Return the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE command.

Description

This command sets or queries the population limit state for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?

Info

MEAS<x> specifies the measurement number.
OFF turns off the population limit.
ON turns on the population limit.
0 turns off the population limit.
1 turns on the population limit.

value `property` ¶

value: MeasurementMeasItemPopulationLimitValue

Return the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue command.

Description

This command sets or queries the population limit value for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue <NR3>
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?

Info

MEAS<x> specifies the measurement number.
<NR3> the current limit value.

MeasurementMeasItemPopulationLimitState ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE command.

Description

This command sets or queries the population limit state for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE {ON|OFF|1|0}
- MEASUrement:MEAS<x>:POPUlation:LIMIT:STATE?

Info

MEAS<x> specifies the measurement number.
OFF turns off the population limit.
ON turns on the population limit.
0 turns off the population limit.
1 turns on the population limit.

MeasurementMeasItemPopulationLimitValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue command.

Description

This command sets or queries the population limit value for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue <NR3>
- MEASUrement:MEAS<x>:POPUlation:LIMIT:VALue?

Info

MEAS<x> specifies the measurement number.
<NR3> the current limit value.

MeasurementMeasItemPowerfactor ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:POWERFACtor command.

Description

This command sets or queries the power factor value for IEC-Class C type harmonics standard. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:POWERFACtor? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:POWERFACtor? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:POWERFACtor value command.

SCPI Syntax

- MEASUrement:MEAS<x>:POWERFACtor <NR2>
- MEASUrement:MEAS<x>:POWERFACtor?

Info

MEAS<x> specifies the measurement number.
<NR2> specifies the power factor value for class C harmonics standard.

MeasurementMeasItemPregion ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PREGion command.

Description

This command sets or returns pulse region for a measurement. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PREGion? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PREGion? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PREGion value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PREGion {FPULse|SPULse|MPULse}
- MEASUrement:MEAS<x>:PREGion?

Info

FPULse is the pulse region as Fpulse.
SPULse is the pulse region as Spulse.
MPULse is the pulse region as Mpulse.

MeasurementMeasItemPresistance ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PRESistance command.

Description

This command sets or returns the probe resistance for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PRESistance? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PRESistance? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PRESistance value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PRESistance <NR3>
- MEASUrement:MEAS<x>:PRESistance?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for probe resistance of the WBG measurement.

MeasurementMeasItemPthreshold ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PTHReshold command.

Description

This command sets or returns the PJ threshold value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PTHReshold? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PTHReshold? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PTHReshold value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PTHReshold <NR3>
- MEASUrement:MEAS<x>:PTHReshold?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of PJ threshold for PSIJ measurement.

MeasurementMeasItemPwidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:PWIDth command.

Description

This command sets or returns pulse width. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:PWIDth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:PWIDth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:PWIDth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:PWIDth <NR3>
- MEASUrement:MEAS<x>:PWIDth?

Info

<NR3> specifies the pulse width.

MeasurementMeasItemRedge ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REDGe command.

Description

This command turns on or off the Refine edge on qualifier. Measurements are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REDGe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REDGe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REDGe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REDGe {ON|OFF}
- MEASUrement:MEAS<x>:REDGe?

Info

ON specifies the Refine edge settings has been turned on.
OFF specifies the Refine edge settings has been turned off.

MeasurementMeasItemReflevels ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.absolute: The MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

absolute `property` ¶

absolute: MeasurementMeasItemReflevelsAbsolute

Return the MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

MeasurementMeasItemReflevels1 ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1 command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.absolute: The MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.
.basetop: The MEASUrement:MEAS<x>:REFLevels1:BASETop command.
.method: The MEASUrement:MEAS<x>:REFLevels1:METHod command.
.percent: The MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

absolute `property` ¶

absolute: MeasurementMeasItemReflevels1Absolute

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.falllow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementMeasItemReflevels1Basetop

Return the MEASUrement:MEAS<x>:REFLevels1:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?

Info

MEAS<x> specifies the measurement number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

method `property` ¶

method: MeasurementMeasItemReflevels1Method

Return the MEASUrement:MEAS<x>:REFLevels1:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?

Info

MEAS<x> specifies the measurement number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MEAS<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MEAS<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

percent `property` ¶

percent: MeasurementMeasItemReflevels1Percent

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Sub-properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.
.falllow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

MeasurementMeasItemReflevels1Absolute ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.falllow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

falllow `property` ¶

falllow: MeasurementMeasItemReflevels1AbsoluteFalllow

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x. Note: This command affects the results of rise and fall measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level in volts. The default is 0.0 V.

fallmid `property` ¶

fallmid: MeasurementMeasItemReflevels1AbsoluteFallmid

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x. Note: This command affects the results of period, frequency, delay, and all cyclic measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level in volts. The default is 0.0 V.

hysteresis `property` ¶

hysteresis: MeasurementMeasItemReflevels1AbsoluteHysteresis

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for autoset.

risehigh `property` ¶

risehigh: MeasurementMeasItemReflevels1AbsoluteRisehigh

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

riselow `property` ¶

riselow: MeasurementMeasItemReflevels1AbsoluteRiselow

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

risemid `property` ¶

risemid: MeasurementMeasItemReflevels1AbsoluteRisemid

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

type `property` ¶

type: MeasurementMeasItemReflevels1AbsoluteType

Return the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?

Info

MEAS<x> specifies the measurement number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMeasItemReflevels1AbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x. Note: This command affects the results of rise and fall measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level in volts. The default is 0.0 V.

MeasurementMeasItemReflevels1AbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x. Note: This command affects the results of period, frequency, delay, and all cyclic measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level in volts. The default is 0.0 V.

MeasurementMeasItemReflevels1AbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for autoset.

MeasurementMeasItemReflevels1AbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

MeasurementMeasItemReflevels1AbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the low reference level, and is the zero percent level when the measurement’s Ref level method is set to Absolute.

MeasurementMeasItemReflevels1AbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the mid reference level (where 50% is equal to MID) used to calculate the mid reference level when the measurement’s Ref level method is set to Absolute.

MeasurementMeasItemReflevels1AbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:MEAS<x>:REFLevels1:ABSolute:TYPE?

Info

MEAS<x> specifies the measurement number.
SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementMeasItemReflevels1Basetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:BASETop value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:MEAS<x>:REFLevels1:BASETop?

Info

MEAS<x> specifies the measurement number.
AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

MeasurementMeasItemReflevels1Method ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:METHod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:METHod {PERCent|ABSolute}
- MEASUrement:MEAS<x>:REFLevels1:METHod?

Info

MEAS<x> specifies the measurement number.
PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:MEAS<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:MEAS<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementMeasItemReflevels1Percent ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.
.falllow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.
.fallmid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.
.hysteresis: The MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.
.riselow: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.
.risemid: The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.
.type: The MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementMeasItemReflevels1PercentFallhigh

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level.

falllow `property` ¶

falllow: MeasurementMeasItemReflevels1PercentFalllow

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level.

fallmid `property` ¶

fallmid: MeasurementMeasItemReflevels1PercentFallmid

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level.

hysteresis `property` ¶

hysteresis: MeasurementMeasItemReflevels1PercentHysteresis

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 99% is equal to MAX and 1% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for the autoset.

risehigh `property` ¶

risehigh: MeasurementMeasItemReflevels1PercentRisehigh

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 99% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

riselow `property` ¶

riselow: MeasurementMeasItemReflevels1PercentRiselow

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 99% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

risemid `property` ¶

risemid: MeasurementMeasItemReflevels1PercentRisemid

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

type `property` ¶

type: MeasurementMeasItemReflevels1PercentType

Return the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?

Info

MEAS<x> specifies the measurement number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMeasItemReflevels1PercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the high reference level.

MeasurementMeasItemReflevels1PercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLLow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 100% is equal to HIGH) used to calculate the mid reference level.

MeasurementMeasItemReflevels1PercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:FALLMid?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 50% is equal to MID) used to calculate the mid reference level.

MeasurementMeasItemReflevels1PercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 99% is equal to MAX and 1% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:HYSTeresis?

Info

MEAS<x> specifies the measurement number.
<NR3> is the hysteresis value used for the autoset.

MeasurementMeasItemReflevels1PercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 99% is equal to TOP) used to calculate the high reference level when the measurement’s Ref level method is set to Percent.

MeasurementMeasItemReflevels1PercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISELow?

Info

MEAS<x> specifies the measurement number.
<NR3> is the percentage (where 99% is equal to TOP) used to calculate the mid reference level when the measurement’s Ref level method is set to Percent.

MeasurementMeasItemReflevels1PercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid <NR3>
- MEASUrement:MEAS<x>:REFLevels1:PERCent:RISEMid?

Info

MEAS<x> specifies the measurement number.
<NR3> the percentage (where 50% is equal to MID) used to calculate the mid reference level when the measurement Ref level method is set to Percent.

MeasurementMeasItemReflevels1PercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE command.

Description

This command specifies or queries the reference level percent type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:MEAS<x>:REFLevels1:PERCent:TYPE?

Info

MEAS<x> specifies the measurement number.
TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementMeasItemReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.fallhigh: The MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

fallhigh `property` ¶

fallhigh: MeasurementMeasItemReflevelsAbsoluteFallhigh

Return the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x. Note: This command affects the results of rise and fall measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level in volts. The default is 0.0 V.

MeasurementMeasItemReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute. Measurements are specified by x. Note: This command affects the results of rise and fall measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:MEAS<x>:REFLevels:ABSolute:FALLHigh?

Info

MEAS<x> specifies the measurement number.
<NR3> is the high reference level in volts. The default is 0.0 V.

MeasurementMeasItemRefmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFMode command.

Description

This command sets or queries the reference level mode for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFMode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFMode {AUTO|MANual}
- MEASUrement:MEAS<x>:REFMode?

Info

MEAS<x> specifies the measurement number.
AUTO sets the reference level for the measurement automatically.
MANual allows the user to set the reference level for the measurement.

MeasurementMeasItemRefvoltage ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFVoltage command.

Description

This command sets or queries the reference voltage value for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFVoltage? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFVoltage? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFVoltage value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFVoltage <NR3>
- MEASUrement:MEAS<x>:REFVoltage?

Info

MEAS<x> is the measurement number.
<NR3> is the reference voltage value for the selected configuration.

MeasurementMeasItemRefvoltagevalItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:REFVOLTAGE<x>Val command.

Description

Sets or queries the reference voltage per rail of Overshoot and Undershoot measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:REFVOLTAGE<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:REFVOLTAGE<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:REFVOLTAGE<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:REFVOLTAGE<x>Val <NR2>
- MEASUrement:MEAS<x>:REFVOLTAGE<x>Val?

Info

MEAS<x> is the measurement number.
REFVOLTAGE<x> is the rail number.
<NR2> is the reference voltage, in the range of -500 V to +500 V.

MeasurementMeasItemResults ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts? query and raise an AssertionError if the returned value does not match value.

Properties

.allacqs: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.
.history: The MEASUrement:MEAS<x>:RESUlts:HISTory command tree.

allacqs `property` ¶

allacqs: MeasurementMeasItemResultsAllacqs

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

currentacq `property` ¶

currentacq: MeasurementMeasItemResultsCurrentacq

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

history `property` ¶

history: MeasurementMeasItemResultsHistory

Return the MEASUrement:MEAS<x>:RESUlts:HISTory command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev command.

MeasurementMeasItemResultsAllacqs ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemResultsAllacqsMaximum

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum value for all accumulated measurement acquisitions of the specified measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemResultsAllacqsMean

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemResultsAllacqsMinimum

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemResultsAllacqsPk2pk

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak-to-peak value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?

population `property` ¶

population: MeasurementMeasItemResultsAllacqsPopulation

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population measurement value for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemResultsAllacqsStddev

Return the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?

MeasurementMeasItemResultsAllacqsMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum command.

Description

This query-only command returns the maximum value for all accumulated measurement acquisitions of the specified measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MAXimum?

MeasurementMeasItemResultsAllacqsMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN command.

Description

This query-only command returns the mean value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MEAN?

MeasurementMeasItemResultsAllacqsMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum command.

Description

This query-only command returns the minimum value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:MINimum?

MeasurementMeasItemResultsAllacqsPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK command.

Description

This query-only command returns the peak-to-peak value for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:PK2PK?

MeasurementMeasItemResultsAllacqsPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation command.

Description

This query-only command returns the population measurement value for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:POPUlation?

MeasurementMeasItemResultsAllacqsStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev command.

Description

This query-only command returns the standard deviation for all accumulated measurement acquisitions for measurement .

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:ALLAcqs:STDDev?

MeasurementMeasItemResultsCurrentacq ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemResultsCurrentacqMaximum

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemResultsCurrentacqMean

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean value for the measurement for the current acquisition.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?

Info

MEAS<x> is the measurement number for which to return a value. This is the equivalent of the number shown in the measurement badge on the UI.

minimum `property` ¶

minimum: MeasurementMeasItemResultsCurrentacqMinimum

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemResultsCurrentacqPk2pk

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak-to-peak value for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?

population `property` ¶

population: MeasurementMeasItemResultsCurrentacqPopulation

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemResultsCurrentacqStddev

Return the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation for the specified measurement for all acquisitions accumulated since statistics were last reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?

MeasurementMeasItemResultsCurrentacqMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum command.

Description

This query-only command returns the maximum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MAXimum?

MeasurementMeasItemResultsCurrentacqMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN command.

Description

This query-only command returns the mean value for the measurement for the current acquisition.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MEAN?

Info

MEAS<x> is the measurement number for which to return a value. This is the equivalent of the number shown in the measurement badge on the UI.

MeasurementMeasItemResultsCurrentacqMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum command.

Description

This query-only command returns the minimum value found for the specified measurement since the last statistical reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:MINimum?

MeasurementMeasItemResultsCurrentacqPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK command.

Description

This query-only command returns the peak-to-peak value for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:PK2PK?

MeasurementMeasItemResultsCurrentacqPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation command.

Description

This query-only command returns the population for the specified measurement for the current acquisition. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:POPUlation?

MeasurementMeasItemResultsCurrentacqStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev command.

Description

This query-only command returns the standard deviation for the specified measurement for all acquisitions accumulated since statistics were last reset. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:CURRentacq:STDDev?

MeasurementMeasItemResultsHistory ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:HISTory command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum command.
.mean: The MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN command.
.minimum: The MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK command.
.population: The MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemResultsHistoryMaximum

Return the MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum command.

Description

This query-only command returns the maximum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?

mean `property` ¶

mean: MeasurementMeasItemResultsHistoryMean

Return the MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN command.

Description

This query-only command returns the mean value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?

minimum `property` ¶

minimum: MeasurementMeasItemResultsHistoryMinimum

Return the MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum command.

Description

This query-only command returns the minimum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?

pk2pk `property` ¶

pk2pk: MeasurementMeasItemResultsHistoryPk2pk

Return the MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK command.

Description

This query-only command returns the peak-to-peak value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?

population `property` ¶

population: MeasurementMeasItemResultsHistoryPopulation

Return the MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation command.

Description

This query-only command returns the population value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?

stddev `property` ¶

stddev: MeasurementMeasItemResultsHistoryStddev

Return the MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev command.

Description

This query-only command returns the standard deviation value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?

MeasurementMeasItemResultsHistoryMaximum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum command.

Description

This query-only command returns the maximum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:MAXimum?

MeasurementMeasItemResultsHistoryMean ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN command.

Description

This query-only command returns the mean value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:MEAN?

MeasurementMeasItemResultsHistoryMinimum ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum command.

Description

This query-only command returns the minimum value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:MINimum?

MeasurementMeasItemResultsHistoryPk2pk ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK command.

Description

This query-only command returns the peak-to-peak value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:PK2PK?

MeasurementMeasItemResultsHistoryPopulation ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation command.

Description

This query-only command returns the population value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:POPUlation?

MeasurementMeasItemResultsHistoryStddev ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev command.

Description

This query-only command returns the standard deviation value for the specified measurement for each acquisition in the history. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:RESUlts:HISTory:STDDev?

MeasurementMeasItemRfrequency ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:RFREquency command.

Description

This command sets or returns the center frequency value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RFREquency? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RFREquency? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:RFREquency value command.

SCPI Syntax

- MEASUrement:MEAS<x>:RFREquency <NR3>
- MEASUrement:MEAS<x>:RFREquency?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of center frequency for PSIJ measurement.

MeasurementMeasItemRipplefreqvalItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val command.

Description

Sets or queries the ripple frequency per specified rail for Ripple measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val <NR3>
- MEASUrement:MEAS<x>:RIPPLEFREQ<x>Val?

Info

MEAS<x> is the measurement number.
RIPPLEFREQ<x> is the rail number.
<NR3> is the frequency, in the range of 1 Hz to 4 GHz.

MeasurementMeasItemRrange ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:RRANGE command.

Description

This command sets or returns the span value of PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:RRANGE? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:RRANGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:RRANGE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:RRANGE <NR3>
- MEASUrement:MEAS<x>:RRANGE?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value of span for PSIJ measurement.

MeasurementMeasItemSequence ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SEQuence command.

Description

This command sets or queries the sequence of hall edges. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SEQuence? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SEQuence? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SEQuence value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SEQuence {ABC|ACB}
- MEASUrement:MEAS<x>:SEQuence?

Info

MEAS<x> specifies the measurement number.
ABC specifies the motor Hall edges sequence as ABC.
ACB specifies the motor Hall edges sequence as ACB.

MeasurementMeasItemSignalfrequency ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SIGNALFREQUEncy command.

Description

This command sets or queries line frequency for Harmonics and Ripple line frequency. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SIGNALFREQUEncy? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SIGNALFREQUEncy? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SIGNALFREQUEncy value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SIGNALFREQUEncy {AUTO|FIFTYHZ|SIXTYHZ|FOURHUNDREDHZ|CUSTOM}
- MEASUrement:MEAS<x>:SIGNALFREQUEncy?

Info

MEAS<x> specifies the measurement number.
AUTO specifies the line frequency as auto. Only available for Harmonics line frequency.
FIFTYHZ specifies the line frequency as 50 Hz.
SIXTYHZ specifies the line frequency as 60 Hz.
FOURHUNDREDHZ specifies the line frequency as 400 Hz.
CUSTOM specifies the line frequency as custom.

MeasurementMeasItemSignaltype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SIGNALType command.

Description

This command sets or queries the signal type of source 1 for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SIGNALType? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SIGNALType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SIGNALType value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- MEASUrement:MEAS<x>:SIGNALType?

Info

MEAS<x> specifies the measurement number.
CLOCK specifies a clock signal type.
DATA specifies a data signal type.
AUTO automatically selects the signal type.

MeasurementMeasItemSlabs ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SLABs command.

Description

This command sets or returns the value for the start level in absolute.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SLABs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SLABs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SLABs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SLABs <NR3>
- MEASUrement:MEAS<x>:SLABs?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the start level in absolute.

MeasurementMeasItemSlpct ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SLPCt command.

Description

This command sets or returns the value for the start level in percentage.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SLPCt? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SLPCt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SLPCt value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SLPCt <NR3>
- MEASUrement:MEAS<x>:SLPCt?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the start level in percentage.

MeasurementMeasItemSltype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SLTYpe command.

Description

This command sets or returns the start level source type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SLTYpe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SLTYpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SLTYpe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:SLTYpe?

Info

MEAS<x> specifies the measurement number.
VDS specifies the start level source type as VDS.
ID specifies the start level source type as ID.
VGE specifies the start level source type as VGE.
VCE specifies the start level source type as VCE.
IC specifies the start level source type as IC.

MeasurementMeasItemSmoothingfilter ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:SMOOTHINGFILTER command.

Description

This command sets or queries the status of smoothing filter.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:SMOOTHINGFILTER value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SMOOTHINGFILTER <NR1>

Info

MEAS<x> specifies the measurement number.
<NR1> sets the value to 1 or 0. 1 enables smoothing filter and 0 disables it.

MeasurementMeasItemSource ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:SOURCE command.

Description

This command sets or queries local input source.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:SOURCE value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SOURCE {CH<x>|MATH<x>|REF<x>}

Info

MEAS<x> specifies the measurement number.
CH<x> specifies an analog channel as source.
MATH<x> specifies a math channel as source.
REF<x> specifies a reference waveform as the source.

MeasurementMeasItemSource1 ¶

Bases: SCPICmdWriteNoArguments, SCPICmdRead

The MEASUrement:MEAS<x>:SOUrce1 command.

Description

This command sets or queries the measurement source. The measurement number and source are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SOUrce1? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write() method will send the MEASUrement:MEAS<x>:SOUrce1 command.

SCPI Syntax

- MEASUrement:MEAS<x>:SOUrce1
- MEASUrement:MEAS<x>:SOUrce1?

Info

MEAS<x> specifies the measurement number.
1 specifies the source number.

MeasurementMeasItemSpanvalItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SPAN<x>Val command.

Description

This command sets or returns the span value for PSIJ measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SPAN<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SPAN<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SPAN<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SPAN<x>Val <NR3>
- MEASUrement:MEAS<x>:SPAN<x>Val?

Info

MEAS<x> specifies the measurement number.
SPAN<x> specifies the span number.
<NR3> specifies the span value.

MeasurementMeasItemSrate ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SRATe command.

Description

This command sets or queries the symbol rate for the RRC filter in the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SRATe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SRATe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SRATe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SRATe <NR3>
- MEASUrement:MEAS<x>:SRATe?

Info

<NR3> sets the symbol rate. The default is 3.84e6 and the valid range is 1.0 to 5.0e9.

MeasurementMeasItemSrho ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SRHo command.

Description

This command enables or disables the rho waveform for TDR measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SRHo? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SRHo? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SRHo value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SRHo {ON|OFF}
- MEASUrement:MEAS<x>:SRHo?

Info

ON specifies that rho waveform is enabled for TDR measurement.
OFF specifies that rho waveform is disabled for TDR measurement.

MeasurementMeasItemSsc ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:SSC command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSC? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSC? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.nominalfreq: The MEASUrement:MEAS<x>:SSC:NOMinalfreq command.

nominalfreq `property` ¶

nominalfreq: MeasurementMeasItemSscNominalfreq

Return the MEASUrement:MEAS<x>:SSC:NOMinalfreq command.

Description

This command sets or queries the user-defined frequency for the measurement when the measurement type is SSC. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SSC:NOMinalfreq <NR3>
- MEASUrement:MEAS<x>:SSC:NOMinalfreq?

Info

MEAS<x> specifies the measurement number.
<NR3> is the user-defined nominal frequency type for SSC configurations.

Sub-properties

.selectiontype: The MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

MeasurementMeasItemSscNominalfreq ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SSC:NOMinalfreq command.

Description

This command sets or queries the user-defined frequency for the measurement when the measurement type is SSC. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SSC:NOMinalfreq <NR3>
- MEASUrement:MEAS<x>:SSC:NOMinalfreq?

Info

MEAS<x> specifies the measurement number.
<NR3> is the user-defined nominal frequency type for SSC configurations.

Properties

.selectiontype: The MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

selectiontype `property` ¶

selectiontype: MeasurementMeasItemSscNominalfreqSelectiontype

Return the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

Description

This command sets or queries the frequency detection type for the measurement when the measurement type is SSC. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANual}
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?

Info

MEAS<x> specifies the measurement number.
AUTO automatically sets the detection type.
MANual specifies the manual detection type.

MeasurementMeasItemSscNominalfreqSelectiontype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

Description

This command sets or queries the frequency detection type for the measurement when the measurement type is SSC. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANual}
- MEASUrement:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?

Info

MEAS<x> specifies the measurement number.
AUTO automatically sets the detection type.
MANual specifies the manual detection type.

MeasurementMeasItemSsdirection ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SSDirection command.

Description

This command sets or returns the start search direction for measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SSDirection? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SSDirection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SSDirection value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SSDirection {FORWARD|BACKWARD}
- MEASUrement:MEAS<x>:SSDirection?

Info

FORWARD specifies the start search direction for measurement as forward.
BACKWARD specifies the start search direction for measurement as backward.

MeasurementMeasItemStatus ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:STATUS command.

Description

This command returns the pass fail status, if applicable, for the selected measurement. Measur are specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STATUS? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STATUS? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:STATUS?

Info

PASS specifies that the user specified measurement limit has not been violated.
FAIL specifies that the user specified measurement limit has been violated.

MeasurementMeasItemStlabs ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:STLABs command.

Description

This command sets or returns the value for the stop level in absolute.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STLABs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STLABs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STLABs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STLABs <NR3>
- MEASUrement:MEAS<x>:STLABs?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the stop level in absolute.

MeasurementMeasItemStlpct ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:STLPct command.

Description

This command sets or returns the value for the stop level in percentage.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STLPct? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STLPct? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STLPct value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STLPct <NR3>
- MEASUrement:MEAS<x>:STLPct?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the value for the stop level in percentage.

MeasurementMeasItemStltype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:STLTYpe command.

Description

This command sets or returns the stop level source type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STLTYpe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STLTYpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STLTYpe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STLTYpe {VDS|ID|VGE|VCE|IC}
- MEASUrement:MEAS<x>:STLTYpe?

Info

MEAS<x> specifies the measurement number.
VDS specifies the stop level source type as VDS.
ID specifies the stop level source type as ID.
VGE specifies the stop level source type as VGE.
VCE specifies the stop level source type as VCE.
IC specifies the stop level source type as IC.

MeasurementMeasItemStsdirection ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:STSDirection command.

Description

This command sets or returns the stop search direction for measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STSDirection? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STSDirection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STSDirection value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STSDirection {FORWARD|BACKWARD}
- MEASUrement:MEAS<x>:STSDirection?

Info

FORWARD specifies the stop search direction for measurement as forward.
BACKWARD specifies the stop search direction for measurement as backward.

MeasurementMeasItemStype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:STYPe command.

Description

This command sets or queries the source type.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:STYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:STYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:STYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:STYPe {VOLTage|CURRent|DIFFERENTIAL|SINGLE}
- MEASUrement:MEAS<x>:STYPe?

Info

MEAS<x> specifies the measurement number.
VOLTage sets source type as Voltage.
CURRent sets source type as Current.
DIFFERENTIAL sets source type as Differential.
SINGLE sets source type as Single.

MeasurementMeasItemSubgroup ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:SUBGROUP command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP? query and raise an AssertionError if the returned value does not match value.

Properties

.results: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts command tree.

results `property` ¶

results: MeasurementMeasItemSubgroupResults

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.allacqs: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq command tree.

MeasurementMeasItemSubgroupResults ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts? query and raise an AssertionError if the returned value does not match value.

Properties

.allacqs: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs command tree.
.currentacq: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq command tree.

allacqs `property` ¶

allacqs: MeasurementMeasItemSubgroupResultsAllacqs

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev command.

currentacq `property` ¶

currentacq: MeasurementMeasItemSubgroupResultsCurrentacq

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.maximum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev command.

MeasurementMeasItemSubgroupResultsAllacqs ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum command.
.mean: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN command.
.minimum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK command.
.population: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemSubgroupResultsAllacqsMaximum

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum command.

Description

This query returns the maximum value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

mean `property` ¶

mean: MeasurementMeasItemSubgroupResultsAllacqsMean

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN command.

Description

This query returns the mean value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

minimum `property` ¶

minimum: MeasurementMeasItemSubgroupResultsAllacqsMinimum

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum command.

Description

This query returns the minimum value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

pk2pk `property` ¶

pk2pk: MeasurementMeasItemSubgroupResultsAllacqsPk2pk

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK command.

Description

This query returns the peak-to-peak value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

population `property` ¶

population: MeasurementMeasItemSubgroupResultsAllacqsPopulation

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation command.

Description

This query returns the population value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

stddev `property` ¶

stddev: MeasurementMeasItemSubgroupResultsAllacqsStddev

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev command.

Description

This query returns the standard deviation value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL |TIE|TJBER|RJdd|DJdd|PJ|DDJ|DCD|WIDTHBER.

MeasurementMeasItemSubgroupResultsAllacqsMaximum ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum command.

Description

This query returns the maximum value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MAXimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsAllacqsMean ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN command.

Description

This query returns the mean value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MEAN? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsAllacqsMinimum ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum command.

Description

This query returns the minimum value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:MINimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsAllacqsPk2pk ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK command.

Description

This query returns the peak-to-peak value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:PK2PK? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsAllacqsPopulation ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation command.

Description

This query returns the population value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:POPUlation? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsAllacqsStddev ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev command.

Description

This query returns the standard deviation value of the measurement specified by the string, for all acquisitions.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:ALLAcqs:STDDev? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL |TIE|TJBER|RJdd|DJdd|PJ|DDJ|DCD|WIDTHBER.

MeasurementMeasItemSubgroupResultsCurrentacq ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq? query and raise an AssertionError if the returned value does not match value.

Properties

.maximum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum command.
.mean: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN command.
.minimum: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum command.
.pk2pk: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK command.
.population: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation command.
.stddev: The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev command.

maximum `property` ¶

maximum: MeasurementMeasItemSubgroupResultsCurrentacqMaximum

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum command.

Description

This query returns the maximum value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

mean `property` ¶

mean: MeasurementMeasItemSubgroupResultsCurrentacqMean

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN command.

Description

This query returns the mean value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN? <QString>

Info

<QString> = INPUT |OUTPUT1 |OUTPUT2 |OUTPUT3 |OUTPUT4|OUTPUT5 |OUTPUT6 |OUTPUT7 |RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT |RAIL1FREQUENCY |RAIL1PK2PK|RAIL1RMS |RAIL1RMSFULL |RAIL2FREQUENCY |RAIL2PK2PK|RAIL2RMS |RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS |RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY |RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY |RAIL6PK2PK|RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL |L2LPH1VRMS |L2LPH1VCFactor|L2LPH1TruePwr |L2LPH1RePwr |L2LPH1AppPwr |L2LPH1PwrFactor|L2LPH1PhaseDiff |L2LPH1VPhase |L2LPH2VRMS |L2LPH2VCFactor|L2LPH2TruePwr |L2LPH2RePwr |L2LPH2AppPwr |L2LPH2PwrFactor|L2LPH2PhaseDiff |L2LPH2VPhase |L2LPH3VRMS |L2LPH3VCFactor|L2LPH3TruePwr |L2LPH3RePwr |L2LPH3AppPwr |L2LPH3PwrFactor|L2LPH3PhaseDiff |L2LPH3VPhase |L2NPH1VRMS |L2NPH1VCFactor|L2NPH1TruePwr |L2NPH1RePwr |L2NPH1AppPwr |L2NPH1PwrFactor|L2NPH1PhaseDiff |L2NPH1VPhase |L2NPH2VRMS |L2NPH2VCFactor|L2NPH2TruePwr |L2NPH2RePwr |L2NPH2AppPwr |L2NPH2PwrFactor|L2NPH2PhaseDiff |L2NPH2VPhase |L2NPH3VRMS |L2NPH3VCFactor|L2NPH3TruePwr |L2NPH3RePwr |L2NPH3AppPwr |L2NPH3PwrFactor|L2NPH3PhaseDiff |L2NPH3VPhase |PH1IRMS |PH1IPhase |PH1ICFactor|PH2IRMS |PH2IPhase |PH2ICFactor |PH3IRMS |PH3IPhase |PH3ICFactor|Frequency |L2LPH1F1Mag |L2LPH1F3Mag |L2LPH1THDF |L2LPH1THDR|L2LPH1RMS |L2LPH1IRMS |L2LPH1Status |L2LPH1HarmonicsNumber|L2LPH1Frequency |L2LPH1MagnitudeAbs |L2LPH1MagnitudePct|L2LPH1Phase |L2LPH1Limits |L2LPH1PassFail |L2LPH1Margin|L2LPH2F1Mag |L2LPH2F3Mag |L2LPH2THDF |L2LPH2THDR|L2LPH2RMS |L2LPH2IRMS |L2LPH2Status |L2LPH2HarmonicsNumber|L2LPH2Frequency |L2LPH2MagnitudeAbs |L2LPH2MagnitudePct|L2LPH2Phase |L2LPH2Limits |L2LPH2PassFail |L2LPH2Margin|L2LPH3F1Mag |L2LPH3F3Mag |L2LPH3THDF |L2LPH3THDR |L2LPH3RMS|L2LPH3IRMS |L2LPH3Status |L2LPH3HarmonicsNumber |L2LPH3Frequency|L2LPH3MagnitudeAbs |L2LPH3MagnitudePct |L2LPH3Phase |L2LPH3Limits|L2LPH3PassFail |L2LPH3Margin |L2NPH1F1Mag |L2NPH1F3Mag|L2NPH1THDF |L2NPH1THDR |L2NPH1RMS |L2NPH1IRMS|L2NPH1Status |L2NPH1HarmonicsNumber |L2NPH1Frequency|L2NPH1MagnitudeAbs |L2NPH1MagnitudePct |L2NPH1Phase|L2NPH1Limits|L2NPH1PassFail|L2NPH1Margin |L2NPH2F1Mag|L2NPH2F3Mag|L2NPH2THDF|L2NPH2THDR |L2NPH2RMS|L2NPH2IRMS|L2NPH2Status |L2NPH2HarmonicsNumber |L2NPH2Frequency|L2NPH2MagnitudeAbs |L2NPH2MagnitudePct |L2NPH2Phase|L2NPH2Limits|L2NPH2PassFail|L2NPH2Margin |L2NPH3F1Mag |L2NPH3F3Mag|L2NPH3THDF |L2NPH3THDR |L2NPH3RMS |L2NPH3IRMS |L2NPH3Status|L2NPH3HarmonicsNumber |L2NPH3Frequency |L2NPH3MagnitudeAbs|L2NPH3MagnitudePct |L2NPH3Phase |L2NPH3Limits |L2NPH3PassFail|L2NPH3Margin |ORDER|PH1INPwr |PH1OUTPwr |PH1Efficiency |PH2INPwr|PH2OUTPwr |PH2Efficiency |TotalEfficiency |PH1LRIPRMS |PH1LRIPPK2PK|PH2LRIPRMS |PH2LRIPPK2PK |PH3LRIPRMS |PH3LRIPPK2PK|PH1SWRIPRMS |PH1SWRIPPK2PK |PH2SWRIPRMS |PH2SWRIPPK2PK|PH3SWRIPRMS |PH3SWRIPPK2PK |TruePwrSum |RePwrSum |AppPwrSum|InPwrSum |OutPwrSum |SPEED |ACCELERATION |DIRECTION |ANGLE|TORQUE |POWER |ELECPWR |MECHPWR |SYSTEMEFFICIENCY |EON|EOFF |TDON |TDOFF |startlevel |stoplevel |TRR |QRR |TA |TB |RSF |VPEAK|IPEAK |TR |ERR |TF |TON |TOFF |IRRM |DBYDT |fft |tiespectra |subspectra|beforetie |beforepj |beforeeyeheight |beforeeyewidth |reconst |aftertie |afterpj|aftereyeheight |aftereyewidth |freq |qoss |PH1TDD |PH2TDD |PH3TDD |TDT|zmean |cmean |lmean.

minimum `property` ¶

minimum: MeasurementMeasItemSubgroupResultsCurrentacqMinimum

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum command.

Description

This query returns the minimum value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL |SPEED |ACCELERATION |DIRECTION|ANGLE |TORQUE |POWER |ELECPWR |MECHPWR |SYSTEMEFFICIENCY|EON |EOFF |TDON |TDOFF |startlevel |stoplevel |TRR |QRR |TA |TB |RSF|VPEAK |IPEAK |TR |ERR |TF |TON |TOFF |IRRM |DBYDT |fft |tiespectra|subspectra |beforetie |beforepj |beforeeyeheight |beforeeyewidth |reconst |aftertie|afterpj |aftereyeheight |aftereyewidth |freq |qoss |PH1TDD |PH2TDD |PH3TDD|TDT |zmean |cmean |lmean.

pk2pk `property` ¶

pk2pk: MeasurementMeasItemSubgroupResultsCurrentacqPk2pk

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK command.

Description

This query returns the peak-to-peak value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL is the path and filename, in quotes, of the file containing the data pattern.

population `property` ¶

population: MeasurementMeasItemSubgroupResultsCurrentacqPopulation

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation command.

Description

This query returns the population value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

stddev `property` ¶

stddev: MeasurementMeasItemSubgroupResultsCurrentacqStddev

Return the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev command.

Description

This query returns the standard deviation value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsCurrentacqMaximum ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum command.

Description

This query returns the maximum value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MAXimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsCurrentacqMean ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN command.

Description

This query returns the mean value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MEAN? <QString>

Info

<QString> = INPUT |OUTPUT1 |OUTPUT2 |OUTPUT3 |OUTPUT4|OUTPUT5 |OUTPUT6 |OUTPUT7 |RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT |RAIL1FREQUENCY |RAIL1PK2PK|RAIL1RMS |RAIL1RMSFULL |RAIL2FREQUENCY |RAIL2PK2PK|RAIL2RMS |RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS |RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY |RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY |RAIL6PK2PK|RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL |L2LPH1VRMS |L2LPH1VCFactor|L2LPH1TruePwr |L2LPH1RePwr |L2LPH1AppPwr |L2LPH1PwrFactor|L2LPH1PhaseDiff |L2LPH1VPhase |L2LPH2VRMS |L2LPH2VCFactor|L2LPH2TruePwr |L2LPH2RePwr |L2LPH2AppPwr |L2LPH2PwrFactor|L2LPH2PhaseDiff |L2LPH2VPhase |L2LPH3VRMS |L2LPH3VCFactor|L2LPH3TruePwr |L2LPH3RePwr |L2LPH3AppPwr |L2LPH3PwrFactor|L2LPH3PhaseDiff |L2LPH3VPhase |L2NPH1VRMS |L2NPH1VCFactor|L2NPH1TruePwr |L2NPH1RePwr |L2NPH1AppPwr |L2NPH1PwrFactor|L2NPH1PhaseDiff |L2NPH1VPhase |L2NPH2VRMS |L2NPH2VCFactor|L2NPH2TruePwr |L2NPH2RePwr |L2NPH2AppPwr |L2NPH2PwrFactor|L2NPH2PhaseDiff |L2NPH2VPhase |L2NPH3VRMS |L2NPH3VCFactor|L2NPH3TruePwr |L2NPH3RePwr |L2NPH3AppPwr |L2NPH3PwrFactor|L2NPH3PhaseDiff |L2NPH3VPhase |PH1IRMS |PH1IPhase |PH1ICFactor|PH2IRMS |PH2IPhase |PH2ICFactor |PH3IRMS |PH3IPhase |PH3ICFactor|Frequency |L2LPH1F1Mag |L2LPH1F3Mag |L2LPH1THDF |L2LPH1THDR|L2LPH1RMS |L2LPH1IRMS |L2LPH1Status |L2LPH1HarmonicsNumber|L2LPH1Frequency |L2LPH1MagnitudeAbs |L2LPH1MagnitudePct|L2LPH1Phase |L2LPH1Limits |L2LPH1PassFail |L2LPH1Margin|L2LPH2F1Mag |L2LPH2F3Mag |L2LPH2THDF |L2LPH2THDR|L2LPH2RMS |L2LPH2IRMS |L2LPH2Status |L2LPH2HarmonicsNumber|L2LPH2Frequency |L2LPH2MagnitudeAbs |L2LPH2MagnitudePct|L2LPH2Phase |L2LPH2Limits |L2LPH2PassFail |L2LPH2Margin|L2LPH3F1Mag |L2LPH3F3Mag |L2LPH3THDF |L2LPH3THDR |L2LPH3RMS|L2LPH3IRMS |L2LPH3Status |L2LPH3HarmonicsNumber |L2LPH3Frequency|L2LPH3MagnitudeAbs |L2LPH3MagnitudePct |L2LPH3Phase |L2LPH3Limits|L2LPH3PassFail |L2LPH3Margin |L2NPH1F1Mag |L2NPH1F3Mag|L2NPH1THDF |L2NPH1THDR |L2NPH1RMS |L2NPH1IRMS|L2NPH1Status |L2NPH1HarmonicsNumber |L2NPH1Frequency|L2NPH1MagnitudeAbs |L2NPH1MagnitudePct |L2NPH1Phase|L2NPH1Limits|L2NPH1PassFail|L2NPH1Margin |L2NPH2F1Mag|L2NPH2F3Mag|L2NPH2THDF|L2NPH2THDR |L2NPH2RMS|L2NPH2IRMS|L2NPH2Status |L2NPH2HarmonicsNumber |L2NPH2Frequency|L2NPH2MagnitudeAbs |L2NPH2MagnitudePct |L2NPH2Phase|L2NPH2Limits|L2NPH2PassFail|L2NPH2Margin |L2NPH3F1Mag |L2NPH3F3Mag|L2NPH3THDF |L2NPH3THDR |L2NPH3RMS |L2NPH3IRMS |L2NPH3Status|L2NPH3HarmonicsNumber |L2NPH3Frequency |L2NPH3MagnitudeAbs|L2NPH3MagnitudePct |L2NPH3Phase |L2NPH3Limits |L2NPH3PassFail|L2NPH3Margin |ORDER|PH1INPwr |PH1OUTPwr |PH1Efficiency |PH2INPwr|PH2OUTPwr |PH2Efficiency |TotalEfficiency |PH1LRIPRMS |PH1LRIPPK2PK|PH2LRIPRMS |PH2LRIPPK2PK |PH3LRIPRMS |PH3LRIPPK2PK|PH1SWRIPRMS |PH1SWRIPPK2PK |PH2SWRIPRMS |PH2SWRIPPK2PK|PH3SWRIPRMS |PH3SWRIPPK2PK |TruePwrSum |RePwrSum |AppPwrSum|InPwrSum |OutPwrSum |SPEED |ACCELERATION |DIRECTION |ANGLE|TORQUE |POWER |ELECPWR |MECHPWR |SYSTEMEFFICIENCY |EON|EOFF |TDON |TDOFF |startlevel |stoplevel |TRR |QRR |TA |TB |RSF |VPEAK|IPEAK |TR |ERR |TF |TON |TOFF |IRRM |DBYDT |fft |tiespectra |subspectra|beforetie |beforepj |beforeeyeheight |beforeeyewidth |reconst |aftertie |afterpj|aftereyeheight |aftereyewidth |freq |qoss |PH1TDD |PH2TDD |PH3TDD |TDT|zmean |cmean |lmean.

MeasurementMeasItemSubgroupResultsCurrentacqMinimum ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum command.

Description

This query returns the minimum value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:MINimum? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL |SPEED |ACCELERATION |DIRECTION|ANGLE |TORQUE |POWER |ELECPWR |MECHPWR |SYSTEMEFFICIENCY|EON |EOFF |TDON |TDOFF |startlevel |stoplevel |TRR |QRR |TA |TB |RSF|VPEAK |IPEAK |TR |ERR |TF |TON |TOFF |IRRM |DBYDT |fft |tiespectra|subspectra |beforetie |beforepj |beforeeyeheight |beforeeyewidth |reconst |aftertie|afterpj |aftereyeheight |aftereyewidth |freq |qoss |PH1TDD |PH2TDD |PH3TDD|TDT |zmean |cmean |lmean.

MeasurementMeasItemSubgroupResultsCurrentacqPk2pk ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK command.

Description

This query returns the peak-to-peak value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:PK2PK? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL is the path and filename, in quotes, of the file containing the data pattern.

MeasurementMeasItemSubgroupResultsCurrentacqPopulation ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation command.

Description

This query returns the population value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:POPUlation? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSubgroupResultsCurrentacqStddev ¶

Bases: SCPICmdReadWithArguments

The MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev command.

Description

This query returns the standard deviation value of the measurement specified by the string, for the current acquisition.

Usage

Using the .query(argument) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev? argument query.
Using the .verify(argument, value) method will send the MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev? argument query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:SUBGROUP:RESUlts:CURRentacq:STDDev? <QString>

Info

<QString> = INPUT|OUTPUT1|OUTPUT2|OUTPUT3|OUTPUT4|OUTPUT5|OUTPUT6|OUTPUT7| RAIL1DPMOVERSHOOT|RAIL1DPMUNDERSHOOT|RAIL1FREQUENCY |RAIL1PK2PK |RAIL1RMS|RAIL1RMSFULL|RAIL2FREQUENCY |RAIL2PK2PK |RAIL2RMS|RAIL2RMSFULL |RAIL3FREQUENCY |RAIL3PK2PK|RAIL3RMS|RAIL3RMSFULL |RAIL4FREQUENCY |RAIL4PK2PK|RAIL4RMS |RAIL4RMSFULL |RAIL5FREQUENCY|RAIL5PK2PK|RAIL5RMS |RAIL5RMSFULL |RAIL6FREQUENCY|RAIL6PK2PK |RAIL6RMS |RAIL6RMSFULL |RAIL7DPMOVERSHOOT|RAIL7DPMUNDERSHOOT |RAIL7FREQUENCY |RAIL7PK2PK|RAIL7RMS |RAIL7RMSFULL.

MeasurementMeasItemSunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:SUNits command.

Description

This command sets or queries the speed units for the specific measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:SUNits? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:SUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:SUNits value command.

SCPI Syntax

- MEASUrement:MEAS<x>:SUNits {RPM|HZ}
- MEASUrement:MEAS<x>:SUNits?

Info

MEAS<x> specifies the measurement number.
RPM defines the speed measurement units as RPM.
HZ defines the speed measurement units as HZ.

MeasurementMeasItemTckavg ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TCKAVG command.

Description

This command sets or queries the average clock period value used in DDR measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TCKAVG? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TCKAVG? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TCKAVG value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TCKAVG <NR3>
- MEASUrement:MEAS<x>:TCKAVG?

Info

MEAS<x> specifies the measurement number.
<NR3> is a floating point number that represents the DDR average clock period in seconds.

MeasurementMeasItemTconstant ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TCONstant command.

Description

This command sets or queries the measurement Torque Constant.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TCONstant? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TCONstant? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TCONstant value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TCONstant <NR1>
- MEASUrement:MEAS<x>:TCONstant?

Info

MEAS<x> specifies the measurement number.
NR1 specifies the current multiplier value of the measurement in the range of 0 to 100.

MeasurementMeasItemTdrpreset ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:TDRPreset command.

Description

This command executes the preset for TDR measurement.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:TDRPreset value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TDRPreset {EXECUTE}

Info

MEAS<x> specifies the measurement number.
EXECUTE executes the preset for TDR measurement.

MeasurementMeasItemTimingmode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TIMINGMode command.

Description

This command sets or queries the Timing mode for the specified DDR measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TIMINGMode? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TIMINGMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TIMINGMode value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TIMINGMode {EACHCLOCKCYCLE|TWOCLOCKCYCLES}
- MEASUrement:MEAS<x>:TIMINGMode?

Info

MEAS<x> specifies the measurement number.
EACHCLOCKCYCLE sets the DDR Timing Mode to use each clock cycle at a time.
TWOCLOCKCYCLES sets the DDR Timing Mode to use two cycles at a time.

MeasurementMeasItemTlevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TLEVel command.

Description

This command sets or queries whether histogram center is percentage relative to unit amplitude or an absolute value, for eye height measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TLEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TLEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TLEVel {PERCent|ABSolute}
- MEASUrement:MEAS<x>:TLEVel?

Info

MEAS<x> specifies the measurement number.
PERCent sets the histogram center as a percentage relative to unit amplitude.
ABSolute sets the histogram center as an absolute value.

MeasurementMeasItemTmethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TMEThod command.

Description

This command sets or queries the measurement torque method.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TMEThod? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TMEThod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TMEThod value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TMEThod {SENSOR|CURRENT}
- MEASUrement:MEAS<x>:TMEThod?

Info

MEAS<x> specifies the measurement number.
SENSOR specifies the Torque Method as SENSOR.
CURRENT specifies the Torque Method as CURRENT.

MeasurementMeasItemToedge ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOEdge command.

Description

This command sets or queries the ‘to edge’ type for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEdge? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEdge? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEdge value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEdge {SAMEas|OPPositeas|RISe|FALL|BOTH}
- MEASUrement:MEAS<x>:TOEdge?

Info

MEAS<x> specifies the measurement number.
FALL specifies the falling edge of the waveform.
RISe specifies the rising edge of the waveform.
BOTH specifies both a rising and falling edge of the waveform.
SAMEas specifies that both edges of the waveform are the same.
OPPositeas specifies that the edges of the waveform are not the same.

MeasurementMeasItemToedgesearchdirect ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOEDGESEARCHDIRect command.

Description

This command sets or queries the to edge search direction for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOEDGESEARCHDIRect value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect {FORWard|BACKWard}
- MEASUrement:MEAS<x>:TOEDGESEARCHDIRect?

Info

MEAS<x> specifies the measurement number.
FORWard specifies a forward search to the edge.
BACKWard specifies a backward search to the edge.

MeasurementMeasItemTosymbol ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:TOSYmbol command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.logic2source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce command.
.logic3source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce command.
.logic4source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce command.
.logic5source: The MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce command.
.measureat: The MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT command.

logic2source `property` ¶

logic2source: MeasurementMeasItemTosymbolLogic2source

Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 1 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 1 To Symbol to H (High).
L sets the logic source 1 To Symbol to L (Low).
X sets the logic source 1 To Symbol to X (Don’t care).

logic3source `property` ¶

logic3source: MeasurementMeasItemTosymbolLogic3source

Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 2 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 2 To Symbol to H (High).
L sets the logic source 2 To Symbol to L (Low).
X sets the logic source 2 To Symbol to X (Don’t care).

logic4source `property` ¶

logic4source: MeasurementMeasItemTosymbolLogic4source

Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 3 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 3 To Symbol to H (High).
L sets the logic source 3 To Symbol to L (Low).
X sets the logic source 3 To Symbol to X (Don’t care).

logic5source `property` ¶

logic5source: MeasurementMeasItemTosymbolLogic5source

Return the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 4 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 4 To Symbol to H (High).
L sets the logic source 4 To Symbol to L (Low).
X sets the logic source 4 To Symbol to X (Don’t care).

measureat `property` ¶

measureat: MeasurementMeasItemTosymbolMeasureat

Return the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT command.

Description

This command sets or queries the DDR digital measurement ToSymbol MeasureAT value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?

Info

MEAS<x> specifies the measurement number.
Start sets the ToSymbol MeasureAT to Start.
Stop sets the ToSymbol MeasureAT to Stop.
ClockEdge sets the sets the ToSymbol MeasureAT to ClockEdge.

MeasurementMeasItemTosymbolLogic2source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 1 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC2SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 1 To Symbol to H (High).
L sets the logic source 1 To Symbol to L (Low).
X sets the logic source 1 To Symbol to X (Don’t care).

MeasurementMeasItemTosymbolLogic3source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 2 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC3SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 2 To Symbol to H (High).
L sets the logic source 2 To Symbol to L (Low).
X sets the logic source 2 To Symbol to X (Don’t care).

MeasurementMeasItemTosymbolLogic4source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 3 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC4SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 3 To Symbol to H (High).
L sets the logic source 3 To Symbol to L (Low).
X sets the logic source 3 To Symbol to X (Don’t care).

MeasurementMeasItemTosymbolLogic5source ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce command.

Description

This command sets or queries the DDR digital measurement logic 4 source To Symbol.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce {H|L|X}
- MEASUrement:MEAS<x>:TOSYmbol:LOGIC5SOUrce?

Info

MEAS<x> specifies the measurement number.
H sets the logic source 4 To Symbol to H (High).
L sets the logic source 4 To Symbol to L (Low).
X sets the logic source 4 To Symbol to X (Don’t care).

MeasurementMeasItemTosymbolMeasureat ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT command.

Description

This command sets or queries the DDR digital measurement ToSymbol MeasureAT value.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT {Start|Stop|ClockEdge}
- MEASUrement:MEAS<x>:TOSYmbol:MEASUREAT?

Info

MEAS<x> specifies the measurement number.
Start sets the ToSymbol MeasureAT to Start.
Stop sets the ToSymbol MeasureAT to Stop.
ClockEdge sets the sets the ToSymbol MeasureAT to ClockEdge.

MeasurementMeasItemTransition ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:TRANSition command.

Description

This command sets or queries the transition edges flag for the measurement. The measurement number is specified by x.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:TRANSition value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TRANSition {ON|OFF|<NR1>}

Info

<NR1> = 1, the measurement is computed on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only. If it is set to 0, the measurement is computed on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
OFF computes the measurement on all rising (if measurement type is rise time) or falling (if measurement type is fall time) edges.
ON computes the measurement on rising (if measurement type is rise time) or falling edges (if measurement type is fall time) following a double transition only.

MeasurementMeasItemType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:TYPe command.

Description

This command sets or queries the measurement type for the measurement specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:TYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:TYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:TYPe {ACCOMMONMODE|ACPR|ACRMS|AMPLITUDE|AREA|BASE|BITAMPLITUDE|BITHIGH|BITLOW|BURSTWIDTH|COMMONMODE|CPOWER|DATARATE|DCD|DDJ|DDRAOS|DDRAOSPERTCK|DDRAOSPERUI|DDRAUS|DDRAUSPERTCK|DDRAUSPERUI|DDRHOLDDIFF|DDRSETUPDIFF|DDRTCHABS|DDRTCHAVERAGE|DDRTCKAVERAGE|DDRTCLABS|DDRTCLAVERAGE|DDRTERRMN|DDRTERRN|DDRTJITCC|DDRTJITDUTY|DDRTJITPER|DDRTPST|DDRTRPRE|DDRTWPRE|DDRVIXAC|DDRTDQSCK|DELAY|DJ|DJDIRAC|DPMOVERSHOOT|DPMPSIJ|DPMUNDERSHOOT|DPMRIPPLE|DPMTURNOFFTIME|DPMTURNONTIME|EYEHIGH|EYELOW|FALLSLEWRATE|FALLTIME|FREQUENCY|F2|F4|F8|HIGH|HEIGHT|HEIGHTBER|HIGHTIME|HOLD|IMDAANGLE|IMDADIRECTION|IMDADQ0|IMDAEFFICIENCY|IMDAHARMONICS|IMDAMECHPWR|IMDAPOWERQUALITY|IMDASPEED|IMDASYSEFF|IMDATORQUE|ISI|JITTERSUMMARY|J2|J9|LOW|LOWTIME|MAXIMUM|MEAN|MINIMUM|NDUtY|NPERIOD|NPJ|NOVERSHOOT|NWIDTH|OBW|PATTERNLENGTH|PDUTTY|PERIOD|PHASE|PHASENOISE|PJ|PK2Pk|POVERSHOOT|PWIDTH|QFACTOR|RDSON|RISESLEWRATE|RISETIME|RJ|RJDIRAC|RMS|SRJ|SSCFREQDEV|SSCMODRATE|SSCSLEWRATE|SETUP|SKEW|TDR|TIE|TIMEOUTSIDELEVEL|TJBER|TNTRATIO|TOP|UNITINTERVAL|VDIFFXOVR|WBGDDT|WBGDIODEDDT|WBGEOFF|WBGEON|WBGERR|WBGIPEAK|WBGIRRM|WBGQOSS|WBGQRR|WBGTDOFF|WBGTDON|WBGTF|WBGTON|WBGTOFF|WBGTR|WBGTRR|WBGTDT|WBGVPEAK|WIDTH|WIDTHBER}
- MEASUrement:MEAS<x>:TYPe?

Info

ACCOMMONMODE AC Common Mode (Pk-Pk) is the peak-to-peak of the commonmode voltage of two sources. This measurement is made across the entire record.This measurement requires the DJA option and is not available on a 4 SeriesMSO instrument.
ACPR (Adjacent Channel Power Ratio) is the amount of power that leaks intoadjacent channels. This can be specified in terms of absolute power or a ratio ofadjacent channel power to the main channel power, called adjacent channel powerratio (ACPR) or adjacent channel leakage ratio (ACLR).
ACRMS (AC RMS) is the true Root Mean Square of the data points, about theMean. This measurement can be made across the entire record, or on each cyclein the record.
AMPLITUDE is the difference between the Top value and the Base value. This measurement can be made across the entire record, or on each cycle in the record.
AREA is the area under the curve, calculated by integrating the data points. The area measured above ground is positive. The area measured below ground is negative. This measurement can be made across the entire record, or on each cycle in the record.
BASE is the most common data value below the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
BITAMPLITUDE (Bit Amplitude) is the difference between the amplitudes of the 1 bit and the 0 bit surrounding a transition. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each transition bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITHIGH (Bit High) is the amplitude of a 1 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BITLOW (Bit Low) is the amplitude of a 0 bit. The amplitude is measured over a user specified portion at the center of the recovered unit interval. This measurement is made on each high bit in the record (Mean) or across the entire record (Mode). This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
BURSTWIDTH (Burst Width) is the duration of a series of adjacent crossings of the Mid reference level (RM). Bursts are separated by a user-defined idle time (tI). This measurement is made on each burst in the record.
CCJITTER (Cycle-to-Cycle jitter) measures how much the clock period changes between any two adjacent cycles. Cycle-to-Cycle jitter is measured by applying a first order difference operation to the period jitter.
COMMONMODE (DC Common Mode) is the arithmetic mean of the common mode voltage of two sources. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
CPOWER (Channel Power) is the measurement of integrated power within a specified channel bandwidth for a RF signal. The resulting channel power is an absolute power measurement.
DATARATE (Data Rate) is the reciprocal of Unit Interval. This measurement is made on each bit in the record.
DCD (duty cycle distortion) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the signal polarity. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDJ (data dependent jitter) is the peak-to-peak amplitude of the component of the deterministic jitter correlated with the data pattern in the waveform. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DDRAOS (area above signal) is the total area of the signal above a specified reference level. This measurement is made across the entire record.
DDRAOSPERTCK (area over signal for tCK events) is the total area of the signal above a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAOSPERUI (area over signal for UI events) is the total area of the signal above a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRAUS (area under signal) is the total area of the signal below a specified reference level. This measurement is made across the entire record.
DDRAUSPERTCK (area under signal for tCK events) is the total area of the signal below a specified reference level calculated over consecutive tCK intervals. It is applicable to clock and address/command waveforms.
DDRAUSPERUI (area under signal for UI events) is the total area of the signal below a specified reference level calculated over consecutive unit intervals. It is applicable to data and data strobe waveforms.
DDRHOLDDIFF (hold difference) is the elapsed time between the specified edge of a single-ended clock waveform and the specified edge of a differential data waveform. The measurement uses the closest respective waveform edges that fall within the range limits.This measurement is made across the entire record.
DDRSETUPDIFF (setup difference) is the elapsed time between the specified edge of a single-ended clock waveform and when the specified edge of a differential data waveform crosses a specified level. The measurement uses the closest respective waveform edges that fall within the range limits. This measurement is made across the entire record.
DDRTCHABS (absolute high pulse width) is the absolute value of the high pulse width as measured from one rising edge to the next falling edge.
DDRTCHAVERAGE (average high pulse width) is the average value of the high pulse width as measured from one rising edge to the next falling edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCKAVERAGE (average clock period) is the average clock period calculated from rising edge to rising edge, across 200 consecutive cycles. This measurement is made across the entire record.
DDRTCLABS (absolute low pulse width) is the absolute value of the low pulse width as measured from a falling edge to the next rising edge. This measurement is made across the entire record.
DDRTCLAVERAGE (average low pulse width) is the average value of the low pulse width as measured from one falling edge to the next rising edge, across 200 consecutive cycles.
DDRTERRMN (cumulative error) is the cumulative error across multiple consecutive defined cycles from tCK(avg).
DDRTERRN (cumulative error) is the cumulative error across specified consecutive cycles from tCK(avg). In other words, this measures the time difference between the sum of the clock period from a 200 cycle window and n times tCK(avg).
DDRTJITCC (cycle to cycle jitter period) is the absolute difference in clock period between two consecutive clock cycles. This measurement is made across the entire record.
DDRTJITDUTY (half period jitter) is the largest elapsed time between tCH and tCH(avg), and tCL and tCL(avg), over 200 consecutive cycles.
DDRTJITPER (clock period jitter) is the largest deviation of any tCK signal from tCK(avg). This measurement is made across the entire record.
DDRTPST (read/write burst postamble) is the width of the Read or Write burst postamble, measured from the last falling edge of the mid reference level to the start of an undriven state. This measurement is made across the entire record.
DDRTRPRE (read burst preamble) is the width of the Read burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRTWPRE is the width of theWrite burst preamble, measured from exiting tristate levels to the first driving edge of the differential strobe. This measurement is made across the entire record.
DDRVIXAC is the differential input cross-point voltage measured from the true state transition (and it’s compliment) to a specified reference level, measured on a single-ended signal.
DDRTDQSCK is the strobe output access time, measured between the rising edge of the clock and before or after the differential strobe Read preamble time. Signal edges are determined by the mid-ref threshold level settings.
DELay is the time between the specified Mid reference level (RM) crossing on one source to a specified Mid reference level (RM) crossing on a second source. This measurement is made on the first occurrence in the record.
DJ (deterministic jitter) is the peak-to-peak amplitude of all timing errors that exhibit deterministic behavior. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DJDIRAC (dual-dirac deterministic jitter) is deterministic jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
DPMPSIJ is the Power Supply Induced Jitter. This measurement helps in suppressing the jitter in high speed signals (victim) induced from power rail signals (aggressor).
EYEHIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
EYELOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
FALLSLEWRATE (Falling Slew Rate) is the rate of change in voltage as an edge transitions from the Top reference level (RT) to the Bottom reference level (RB). This measurement is made on each cycle in the record.
FALLTIME (Fall Time) is the time required for an edge to fall from the Top reference level (RT) to the Base reference level (RB). This measurement is made on each cycle in the record.
FREQuency is the reciprocal of Period. This measurement is made on each cycle in the record.
F2 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 2. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F4 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 4. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
F8 is the peak-to-peak amplitude of the periodic jitter occurring at a rate of Fb (data rate) divided by 8. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGH (Eye High) is the amplitude of a high (1) bit measured at a user specified location within the recovered unit interval. This measurement is made on each high bit in the record.
HEIGHT (Eye Height) is the minimum vertical eye opening at the center of the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HEIGHTBER (Eye Height@BER) is the predicted vertical eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
HIGHTIME (High Time) is the time the signal remains above the Top reference level (RT). This measurement is made on each cycle in the record.
HOLD (Hold Time) is the time between the specified Mid reference level crossing (RM) on the Clock source to the closest specified Mid reference level (RM) crossing on the Data source. This measurement is made on each specified Clock edge in the record.
IMDAANGLE (Angle) measures the phase angle. Configure QEI or Hall sensor to.
compute the angle measurement. Requires a IMDA-MECH License.
IMDADIRECTION (Direction) defines the direction of rotation of the motor. Set the direction A-B-C or A-C-B for Hall sensors and CW or CCW for QEI based on the motor configuration. Requires a IMDA-MECH License.
IMDADQ0 measures the DQ0 values of the phasor plot. This measurement requires options IMDA and IMDA-DQ0. Requires a IMDA-MECH License.
IMDAEFFICIENCY (Efficiency) measures the ratio of sum of output power(s) to input power for respective input and output Voltage and Current pairs. Note: the current release cannot support 3V and 3I pairs, since this requires 12 channels. We restrict to 2V and 2I which needs 8 scope channels. Requires a IMDA-MECH License.
IMDAHARMONICS (Harmonics) plots the signal amplitude at the fundamental line frequency and its harmonics and measures the RMS amplitude and Total Harmonic Distortion of the signal. Requires a IMDA-MECH License.
IMDAMECHPWR (Mechanical Power) measures the mechanical power of the motor drive system. It is determined by the Speed and Torque. It is measured in watts. Requires a IMDA-MECH License.
IMDAPOWERQUALITY (Power Quality) measures the Frequency and RMS values of the voltage and current, Crest Factors of the voltage and current, True Power (PTRUE), Reactive Power (PRE), Apparent Power (PAPP), Power Factor, and Phase Angle (θ) of the AC signal. Requires a IMDA-MECH License.
IMDASPEED (Speed) measures the speed and acceleration. Requires a IMDA-MECH License.
IMDASYSEFF (System Efficiency) measures the total efficiency of the motor drive system. Requires a IMDA-MECH License.
IMDATORQUE (Torque) measures the torque of the motor. Configure Sensor (analog) or Current method to measure the torque. Requires a IMDA-MECH License.
ISI (Inter Symbol Interference) is defined as the range (difference between the maximum and minimum value) of DDJ-per-edge values appearing across all rising edges, or the range of DDJ-per-edge values across all falling edges, whichever is greater. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
JITTERSUMMARY (Jitter Summary) is a group consisting of the followingmeasurements: Data Rate, Pattern Length, TIE, TJ@BER, RJ, DJ, DJ-δδ, PJ,DDJ, DCD, Eye Width@BER and RJ-δδ. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
JITTERSUMMARY (Jitter Summary) is a group consisting of the following measurements: TIE, TJ@BER, Eye Width@BER, Eye Height@BER, RJ-δδ, DJ-δδ, PJ, DDJ, DcD, F/2, F/4, F/8. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
J2 is the total jitter at a bit error rate of 2.5e-3 (TJ@2.5e-3). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
J9 is the total jitter at a bit error rate of 2.5e-10 (TJ@2.5e-10). This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
LOW (Eye Low) is the amplitude of a low (0) bit measured at a user specified location within the recovered unit interval. This measurement is made on each low bit in the record.
LOWTIME (Low Time) is the time the signal remains below the Base reference level (RB). This measurement is made on each cycle in the record.
MAXimum is the maximum data point. This measurement can be made across the entire record, or on each cycle in the record.
MEAN is the arithmetic mean of the data points. This measurement can be made across the entire record, or on each cycle in the record.
MINImum is the minimum data point. This measurement can be made across the entire record, or on each cycle in the record.
NDUty (Negative Duty Cycle) is the ratio of the Negative Pulse Width to the Period. This measurement is made on each cycle in the record.
NPERIOD (Duration N-Periods) is the time required to complete N cycles. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
NPJ (non-periodic jitter) is the portion of the BUJ (bounded uncorrelated jitter) that is random. BUJ excludes DDJ, DCD and RJ. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
NOVershoot (Negative Overshoot) is the difference between Minimum and Base, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
NWIDTH (Negative Pulse Width) is the time the signal remains below the Mid reference level (RM). This measurement is made on each cycle in the record.
OBW (Occupied Bandwidth) refers to the bandwidth, including energy of a certain proportion of the total transmitted power, with the center frequency of the specified channel as the center.
PATTERNLENGTH (Pattern Length) is the number of symbols that constitute onefull repetition of a sequence within a signal. This measurement requires the DJAoption and is not available on a 4 Series MSO instrument.
PDUTY (Positive Duty Cycle) is the ratio of the Positive Pulse Width to the Period. This measurement is made on each cycle in the record.
PERIOD is the time required to complete a cycle. A cycle is the time between two adjacent (same direction) crossings of the Mid reference level (RM). This measurement is made on each cycle in the record.
PHASE is the ratio of the Skew between two sources to the Period of the first source. This measurement is made on each cycle in the record.
PHASENOISE (Phase Noise) is the RMS magnitude of all integrated jitter falling within a user specified offset range of the fundamental clock frequency. This measurement is made across the entire record. This measurement is not available on a 4 Series MSO instrument.
PJ (periodic jitter) is the peak-to-peak amplitude of the uncorrelated sinusoidal components of the deterministic jitter. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
PK2Pk (Peak-to-peak) is the difference between Maximum and Minimum. This measurement can be made across the entire record, or on each cycle in the record.
POVERSHOOT (Positive Overshoot) is the difference between Maximum and Top, divided by the Amplitude. This measurement can be made across the entire record, or on each cycle in the record.
PWIDTH (Positive Pulse Width) is the time the signal remains above the Mid reference level (RM). This measurement is made on each cycle in the record.
QFACTOR (Q-Factor) is the ratio of the vertical eye opening to RMS vertical noise measured at a user specified location within the recovered unit interval. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RDSON (Dynamic resistance) is the resistance offered by a switching device whendevice is in ON condition. RDS(on) measurement will provide trend of dynamicresistance on auto created math waveform.
RISESLEWRATE (Rising Slew Rate) is the rate of change in voltage as an edge transitions from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RISETIME Rise Time is the time required for an edge to rise from the Base reference level (RB) to the Top reference level (RT). This measurement is made on each cycle in the record.
RJ (random jitter) is the RMS magnitude of all random timing errors following a Gaussian distribution. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RJDIRAC (dual-dirac random jitter) is random jitter based on a simplifying assumption that the histogram of all deterministic jitter can be modeled as a pair of equal-magnitude Dirac functions. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
RMS is the true Root Mean Square of the data points. This measurement can be made across the entire record, or on each cycle in the record.
SRJ (sub-rate jitter) is the composite jitter due to periodic components at 1/2, 1/4 and 1/8 of the data rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCFREQDEV (SSC Frequency Deviation) is the spread spectrum clock frequency deviation. This measurement enables a time trend plot of the spread spectrum clock modulation profile. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCMODRATE (SSC Modulation Rate) is the modulating frequency of a spread spectrum clock. This measurement is made on each cycle in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
SSCSLEWRATE (SSC Slew Rate) is the rate of change of the modulating frequencyof a spread spectrum clock. This measurement is made on each cycle in therecord. This measurement requires the DJA option and is not available on a 4Series MSO instrument.
SETUP (Setup Time) is the time between the specified Mid reference level (R.
SKEW Skew is the time between the specified Mid reference level (R.
TIE (time interval error) is the difference, in time, between an edge in the source waveform and the corresponding edge in a recovered reference clock. This measurement is made on each edge in the waveform. This measurement is not available on a 4 Series MSO instrument.
TIMEOUTSIDELEVEL Time Outside Level is the time the signal remains above the Top reference level (RT) and/or below the Base reference level (R.
TIMETOMAX Time to Max is the amount of time from the trigger point to the maximum data point. This measurement can be made across the entire record or on each cycle in the record.
TIMETOMIN Time to Min is the amount of time from the trigger point to the minimum data point. This measurement can be made across the entire record or on each cycle in the record.
TJBER (total jitter at a specified bit error rate) is the predicted peak-to-peak amplitude of jitter that will only be exceeded with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TNTRATIO T/nT Ratio is the ratio of a non-transition bit voltage (2nd and subsequent bit voltage after a transition) to its nearest preceding transition bit voltage (1st bit voltage after the transition). Bit voltages are measured at the interpolated midpoint of the recovered unit interval. This measurement is made on each non-transition bit in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
TOP is the most common data value above the midpoint of the waveform. This measurement can be made across the entire record, or on each cycle in the record.
UNITINTERVAL (Unit Interval) is the time difference between two successive bits. This measurement is made on each bit in the record.
VDIFFXOVR (Differential Crossover) is the voltage level of a differential signal pair at the crossover points. This measurement is made at each crossover point in the record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WBGDDT (d/dt) measures the rate of change of voltage or current (slew rate) from the configured start level to the stop level. Requires a WBG-DPT License.
WBGDIODEDDT (Diode d/dt) measures the rate of change of voltage or current (slew rate) during the specified start and stop integration levels. Diode d/dt can be measured during rising or falling edge. Requires a WBG-DPT License.
WBGEOFF (Eoff) measures the energy dissipated in the Power Device during off region using the configured levels. Requires a WBG-DPT License.
WBGEON (Eon) measures the energy dissipated in the Power Device during on region using the configured levels. Requires a WBG-DPT License.
WBGERR (Err) measures the reverse recovery energy dissipated in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGIPEAK (Ipeak) measures the peak current of the Power Device in the on region. Requires a WBG-DPT License.
WBGIRRM (Irrm) measures the maximum current dissipated in the Power Device in the reverse recovery region. Requires a WBG-DPT License.
WBGQOSS (Qoss) is the charge that must be supplied to the output capacitance of the power device during a specified time interval. Requires a WBG-DPT License.
WBGQRR (Qrr) measures the reverse recovery charge in the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDOFF (Td(off)) measures the turn off delay time of the Power Device in the off region using the configured levels. Requires a WBG-DPT License.
WBGTDON (Td(on)) measures the turn on delay time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTF (Tf) measures the fall time of the Power Device in the off region using the configured levels.
WBGTOFF (Toff) measures the turn off time of the Power Device. It is the sum of the turn off delay time and the fall time. Requires a WBG-DPT License.
WBGTON (Ton) measures the turn on time of the Power Device. It is the sum of the turn on delay time and the rise time. Requires a WBG-DPT License.
WBGTR (Tr) measures the rise time of the Power Device in the on region using the configured levels. Requires a WBG-DPT License.
WBGTRR (Trr) measures the reverse recovery time of the Power Device using the configured levels. Requires a WBG-DPT License.
WBGTDT (Tdt) the time delay between turn on time of the high side MOSFET and turn on time of the low side MOSFET during the simultaneous switching. Requires a WBG-DPT License.
WBGVPEAK (Vpeak) measures the peak voltage of the Power Device in the off region. Requires a WBG-DPT License.
WIDTH (Eye Width) is the minimum horizontal eye opening at the user specified reference level. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.
WIDTHBER (Eye Width@BER) is the predicted horizontal eye opening that will be violated with a probability equal to the bit error rate. This measurement is made across the entire record. This measurement requires the DJA option and is not available on a 4 Series MSO instrument.

MeasurementMeasItemVlevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:VLEVel command.

Description

This command sets or queries whether histogram center is percentage relative to unit interval or an absolute value for eye width measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:VLEVel? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:VLEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:VLEVel value command.

SCPI Syntax

- MEASUrement:MEAS<x>:VLEVel {PERCent|ABSolute}
- MEASUrement:MEAS<x>:VLEVel?

Info

MEAS<x> is the measurement number.
PERCent sets the histogram center as a percentage relative to unit interval.
ABSolute sets the histogram center as an absolute value.

MeasurementMeasItemWaittime ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WAITTime command.

Description

Sets or queries the wait time.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WAITTime? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WAITTime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WAITTime value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WAITTime <NR2>
- MEASUrement:MEAS<x>:WAITTime?

Info

MEAS<x> is the measurement number.
<NR2> is the wait time, in the range of 1 s to 500 s.

MeasurementMeasItemWbg ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:WBG command tree.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG? query and raise an AssertionError if the returned value does not match value.

Info

MEAS<x> specifies the measurement number.

Properties

.afgsetup: The MEASUrement:MEAS<x>:WBG:AFGSetup command.
.afgaddress: The MEASUrement:MEAS<x>:WBG:AFGaddress command.
.cstatus: The MEASUrement:MEAS<x>:WBG:CSTatus command.
.gtype: The MEASUrement:MEAS<x>:WBG:GTYPe command.
.high: The MEASUrement:MEAS<x>:WBG:HIGH command.
.load: The MEASUrement:MEAS<x>:WBG:LOAD command.
.low: The MEASUrement:MEAS<x>:WBG:LOW command.
.npuls: The MEASUrement:MEAS<x>:WBG:NPULs command.
.pgval: The MEASUrement:MEAS<x>:WBG:PG<x>Val command.
.pwval: The MEASUrement:MEAS<x>:WBG:PW<x>Val command.
.timer: The MEASUrement:MEAS<x>:WBG:TIMer command.

afgaddress `property` ¶

afgaddress: MeasurementMeasItemWbgAfgaddress

Return the MEASUrement:MEAS<x>:WBG:AFGaddress command.

Description

This command sets or returns the AFG address of external AFG connected for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:AFGaddress? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:AFGaddress? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:AFGaddress value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:AFGaddress <QString>
- MEASUrement:MEAS<x>:WBG:AFGaddress?

Info

MEAS<x> specifies the measurement number.
<QString> specifies the AFG IP address to connect external AFG for WBG measurements.

afgsetup `property` ¶

afgsetup: MeasurementMeasItemWbgAfgsetup

Return the MEASUrement:MEAS<x>:WBG:AFGSetup command.

Description

This command executes AFG test connection or once AFG connection succeeded, Run will setup configuration on connected AFG.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:AFGSetup value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:AFGSetup {CONNECT|RUN}

Info

MEAS<x> specifies the measurement number.
CONNECT executes AFG test connection.
RUN will setup AFG configuration.

cstatus `property` ¶

cstatus: MeasurementMeasItemWbgCstatus

Return the MEASUrement:MEAS<x>:WBG:CSTatus command.

Description

This command queries the AFG test connection status.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:CSTatus? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:CSTatus? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:CSTatus?

Info

MEAS<x> specifies the measurement number.

gtype `property` ¶

gtype: MeasurementMeasItemWbgGtype

Return the MEASUrement:MEAS<x>:WBG:GTYPe command.

Description

This command sets or returns the generator type for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:GTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:GTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:GTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:GTYPe {AFG31000|OTHER}
- MEASUrement:MEAS<x>:WBG:GTYPe?

Info

MEAS<x> specifies the measurement number.
AFG31000 specifies the generator type for WBG measurement as AFG31000.
OTHER specifies the generator type for WBG measurement as OTHER.

high `property` ¶

high: MeasurementMeasItemWbgHigh

Return the MEASUrement:MEAS<x>:WBG:HIGH command.

Description

This command sets or returns the high voltage value of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:HIGH? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:HIGH? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:HIGH value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:HIGH <NR3>
- MEASUrement:MEAS<x>:WBG:HIGH?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the high voltage of AFG for WBG measurements.

load `property` ¶

load: MeasurementMeasItemWbgLoad

Return the MEASUrement:MEAS<x>:WBG:LOAD command.

Description

This command sets or returns the load type of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:LOAD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:LOAD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:LOAD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:LOAD {FIFTY|HIGHZ}
- MEASUrement:MEAS<x>:WBG:LOAD?

Info

MEAS<x> specifies the measurement number.
FIFTY specifies the load type of AFG as Fifty for WBG measurements.
HIGHZ specifies the load type of AFG as High Z for WBG measurements.

low `property` ¶

low: MeasurementMeasItemWbgLow

Return the MEASUrement:MEAS<x>:WBG:LOW command.

Description

This command sets or returns the low voltage value of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:LOW? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:LOW? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:LOW value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:LOW <NR3>
- MEASUrement:MEAS<x>:WBG:LOW?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the low voltage of AFG for WBG measurements.

npuls `property` ¶

npuls: MeasurementMeasItemWbgNpuls

Return the MEASUrement:MEAS<x>:WBG:NPULs command.

Description

This command sets or returns the number of pulse of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:NPULs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:NPULs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:NPULs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:NPULs <NR1>
- MEASUrement:MEAS<x>:WBG:NPULs?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the number of pulse of AFG to generate pulse signal for WBG measurements.

pgval `property` ¶

pgval: dict[int, MeasurementMeasItemWbgPgvalItem]

Return the MEASUrement:MEAS<x>:WBG:PG<x>Val command.

Description

This command sets or returns the pulse gap of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:PG<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:PG<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:PG<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:PG<x>Val <NR3>
- MEASUrement:MEAS<x>:WBG:PG<x>Val?

Info

MEAS<x> specifies the measurement number.
PG<x> specifies the number of pulse. The valid values are 1 to 8.
<NR3> specifies the pulse gap of AFG for WBG measurements.

pwval `property` ¶

pwval: dict[int, MeasurementMeasItemWbgPwvalItem]

Return the MEASUrement:MEAS<x>:WBG:PW<x>Val command.

Description

This command sets or returns the pulse width of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:PW<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:PW<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:PW<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:PW<x>Val <NR3>
- MEASUrement:MEAS<x>:WBG:PW<x>Val?

Info

MEAS<x> specifies the measurement number.
PG<x> specifies the number of pulse. The valid values are 1 to 8.
<NR3> specifies the pulse gap of AFG for WBG measurements.

timer `property` ¶

timer: MeasurementMeasItemWbgTimer

Return the MEASUrement:MEAS<x>:WBG:TIMer command.

Description

This command sets or returns the trigger interval of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:TIMer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:TIMer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:TIMer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:TIMer <NR3>
- MEASUrement:MEAS<x>:WBG:TIMer?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the pulse gap of AFG for WBG measurements.

MeasurementMeasItemWbgAfgaddress ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:AFGaddress command.

Description

This command sets or returns the AFG address of external AFG connected for WBG measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:AFGaddress? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:AFGaddress? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:AFGaddress value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:AFGaddress <QString>
- MEASUrement:MEAS<x>:WBG:AFGaddress?

Info

MEAS<x> specifies the measurement number.
<QString> specifies the AFG IP address to connect external AFG for WBG measurements.

MeasurementMeasItemWbgAfgsetup ¶

Bases: SCPICmdWrite

The MEASUrement:MEAS<x>:WBG:AFGSetup command.

Description

This command executes AFG test connection or once AFG connection succeeded, Run will setup configuration on connected AFG.

Usage

Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:AFGSetup value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:AFGSetup {CONNECT|RUN}

Info

MEAS<x> specifies the measurement number.
CONNECT executes AFG test connection.
RUN will setup AFG configuration.

MeasurementMeasItemWbgCstatus ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:WBG:CSTatus command.

Description

This command queries the AFG test connection status.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:CSTatus? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:CSTatus? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:CSTatus?

Info

MEAS<x> specifies the measurement number.

MeasurementMeasItemWbgGtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:GTYPe command.

Description

This command sets or returns the generator type for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:GTYPe? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:GTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:GTYPe value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:GTYPe {AFG31000|OTHER}
- MEASUrement:MEAS<x>:WBG:GTYPe?

Info

MEAS<x> specifies the measurement number.
AFG31000 specifies the generator type for WBG measurement as AFG31000.
OTHER specifies the generator type for WBG measurement as OTHER.

MeasurementMeasItemWbgHigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:HIGH command.

Description

This command sets or returns the high voltage value of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:HIGH? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:HIGH? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:HIGH value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:HIGH <NR3>
- MEASUrement:MEAS<x>:WBG:HIGH?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the high voltage of AFG for WBG measurements.

MeasurementMeasItemWbgLoad ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:LOAD command.

Description

This command sets or returns the load type of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:LOAD? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:LOAD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:LOAD value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:LOAD {FIFTY|HIGHZ}
- MEASUrement:MEAS<x>:WBG:LOAD?

Info

MEAS<x> specifies the measurement number.
FIFTY specifies the load type of AFG as Fifty for WBG measurements.
HIGHZ specifies the load type of AFG as High Z for WBG measurements.

MeasurementMeasItemWbgLow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:LOW command.

Description

This command sets or returns the low voltage value of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:LOW? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:LOW? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:LOW value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:LOW <NR3>
- MEASUrement:MEAS<x>:WBG:LOW?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the low voltage of AFG for WBG measurements.

MeasurementMeasItemWbgNpuls ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:NPULs command.

Description

This command sets or returns the number of pulse of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:NPULs? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:NPULs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:NPULs value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:NPULs <NR1>
- MEASUrement:MEAS<x>:WBG:NPULs?

Info

MEAS<x> specifies the measurement number.
<NR1> specifies the number of pulse of AFG to generate pulse signal for WBG measurements.

MeasurementMeasItemWbgPgvalItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:PG<x>Val command.

Description

This command sets or returns the pulse gap of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:PG<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:PG<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:PG<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:PG<x>Val <NR3>
- MEASUrement:MEAS<x>:WBG:PG<x>Val?

Info

MEAS<x> specifies the measurement number.
PG<x> specifies the number of pulse. The valid values are 1 to 8.
<NR3> specifies the pulse gap of AFG for WBG measurements.

MeasurementMeasItemWbgPwvalItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:PW<x>Val command.

Description

This command sets or returns the pulse width of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:PW<x>Val? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:PW<x>Val? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:PW<x>Val value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:PW<x>Val <NR3>
- MEASUrement:MEAS<x>:WBG:PW<x>Val?

Info

MEAS<x> specifies the measurement number.
PG<x> specifies the number of pulse. The valid values are 1 to 8.
<NR3> specifies the pulse gap of AFG for WBG measurements.

MeasurementMeasItemWbgTimer ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WBG:TIMer command.

Description

This command sets or returns the trigger interval of AFG for WBG measurements.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WBG:TIMer? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WBG:TIMer? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WBG:TIMer value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WBG:TIMer <NR3>
- MEASUrement:MEAS<x>:WBG:TIMer?

Info

MEAS<x> specifies the measurement number.
<NR3> specifies the pulse gap of AFG for WBG measurements.

MeasurementMeasItemWidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WIDTh command.

Description

This command sets or queries the histogram width in terms of percentage.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WIDTh? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WIDTh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WIDTh value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WIDTh <NR1>
- MEASUrement:MEAS<x>:WIDTh?

Info

MEAS<x> specifies the measurement number.
<NR1> is the value for the width.

MeasurementMeasItemWindowlength ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEAS<x>:WINDOWLENgth command.

Description

This command sets or queries the window length for the measurement. The measurement number is specified by x.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:WINDOWLENgth? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:WINDOWLENgth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEAS<x>:WINDOWLENgth value command.

SCPI Syntax

- MEASUrement:MEAS<x>:WINDOWLENgth <NR3>
- MEASUrement:MEAS<x>:WINDOWLENgth?

Info

<NR3> is the value for the window length.

MeasurementMeasItemXunit ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:XUNIT command.

Description

Returns the horizontal scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:XUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:XUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:XUNIT?

Info

MEAS<x> specifies the measurement number.

MeasurementMeasItemYunit ¶

Bases: SCPICmdRead

The MEASUrement:MEAS<x>:YUNIT command.

Description

Returns the vertical scale units of the specified measurement.

Usage

Using the .query() method will send the MEASUrement:MEAS<x>:YUNIT? query.
Using the .verify(value) method will send the MEASUrement:MEAS<x>:YUNIT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- MEASUrement:MEAS<x>:YUNIT?

Info

MEAS<x> specifies the measurement number.

MeasurementMeasrange ¶

Bases: SCPICmdRead

The MEASUrement:MEASRange command tree.

Usage

Using the .query() method will send the MEASUrement:MEASRange? query.
Using the .verify(value) method will send the MEASUrement:MEASRange? query and raise an AssertionError if the returned value does not match value.

Properties

.max: The MEASUrement:MEASRange:MAX command.
.min: The MEASUrement:MEASRange:MIN command.
.state: The MEASUrement:MEASRange:STATE command.

max `property` ¶

max: MeasurementMeasrangeMax

Return the MEASUrement:MEASRange:MAX command.

Description

This command sets or queries the global range maximum value.

Usage

Using the .query() method will send the MEASUrement:MEASRange:MAX? query.
Using the .verify(value) method will send the MEASUrement:MEASRange:MAX? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEASRange:MAX value command.

SCPI Syntax

- MEASUrement:MEASRange:MAX <NR3>
- MEASUrement:MEASRange:MAX?

Info

<NR3> is the maximum measurement range limit value.

min `property` ¶

min: MeasurementMeasrangeMin

Return the MEASUrement:MEASRange:MIN command.

Description

This command sets or queries the global range minimum value.

Usage

Using the .query() method will send the MEASUrement:MEASRange:MIN? query.
Using the .verify(value) method will send the MEASUrement:MEASRange:MIN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEASRange:MIN value command.

SCPI Syntax

- MEASUrement:MEASRange:MIN <NR3>
- MEASUrement:MEASRange:MIN?

Info

<NR3> is the minimum measurement range limit value.

state `property` ¶

state: MeasurementMeasrangeState

Return the MEASUrement:MEASRange:STATE command.

Description

This command sets or queries the global range state.

Usage

Using the .query() method will send the MEASUrement:MEASRange:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEASRange:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEASRange:STATE value command.

SCPI Syntax

- MEASUrement:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEASRange:STATE?

Info

OFF specifies that the measurement results are not limited.
ON specifies that the measurement results are limited to results with values between the range minimum and maximum.
0 specifies that the measurement results are not limited.
1 specifies that the measurement results are limited to results with values between the range minimum and maximum.

MeasurementMeasrangeMax ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEASRange:MAX command.

Description

This command sets or queries the global range maximum value.

Usage

Using the .query() method will send the MEASUrement:MEASRange:MAX? query.
Using the .verify(value) method will send the MEASUrement:MEASRange:MAX? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEASRange:MAX value command.

SCPI Syntax

- MEASUrement:MEASRange:MAX <NR3>
- MEASUrement:MEASRange:MAX?

Info

<NR3> is the maximum measurement range limit value.

MeasurementMeasrangeMin ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEASRange:MIN command.

Description

This command sets or queries the global range minimum value.

Usage

Using the .query() method will send the MEASUrement:MEASRange:MIN? query.
Using the .verify(value) method will send the MEASUrement:MEASRange:MIN? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEASRange:MIN value command.

SCPI Syntax

- MEASUrement:MEASRange:MIN <NR3>
- MEASUrement:MEASRange:MIN?

Info

<NR3> is the minimum measurement range limit value.

MeasurementMeasrangeState ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MEASRange:STATE command.

Description

This command sets or queries the global range state.

Usage

Using the .query() method will send the MEASUrement:MEASRange:STATE? query.
Using the .verify(value) method will send the MEASUrement:MEASRange:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MEASRange:STATE value command.

SCPI Syntax

- MEASUrement:MEASRange:STATE {ON|OFF|1|0}
- MEASUrement:MEASRange:STATE?

Info

OFF specifies that the measurement results are not limited.
ON specifies that the measurement results are limited to results with values between the range minimum and maximum.
0 specifies that the measurement results are not limited.
1 specifies that the measurement results are limited to results with values between the range minimum and maximum.

MeasurementMech ¶

Bases: SCPICmdRead

The MEASUrement:MECH command tree.

Usage

Using the .query() method will send the MEASUrement:MECH? query.
Using the .verify(value) method will send the MEASUrement:MECH? query and raise an AssertionError if the returned value does not match value.

Properties

.eindexz: The MEASUrement:MECH:EINDexz command.
.gratio: The MEASUrement:MECH:GRATio command.
.munits: The MEASUrement:MECH:MUNits command.
.ppairs: The MEASUrement:MECH:PPAirs command.
.pprotation: The MEASUrement:MECH:PPRotation command.
.source1: The MEASUrement:MECH:SOUrce1 command.
.stype: The MEASUrement:MECH:STYPe command.

eindexz `property` ¶

eindexz: MeasurementMechEindexz

Return the MEASUrement:MECH:EINDexz command.

Description

This command sets or queries the global mechanical Index Z source.

Usage

Using the .query() method will send the MEASUrement:MECH:EINDexz? query.
Using the .verify(value) method will send the MEASUrement:MECH:EINDexz? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:EINDexz value command.

SCPI Syntax

- MEASUrement:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MECH:EINDexz?

Info

ON specifies the Index Z check box state as enabled.
OFF specifies the Index Z check box state as disabled.
1 specifies the Index Z check box state as enabled.
0 specifies the Index Z check box state as disabled.

gratio `property` ¶

gratio: MeasurementMechGratio

Return the MEASUrement:MECH:GRATio command.

Description

This command sets or queries the measurement gear ratio.

Usage

Using the .query() method will send the MEASUrement:MECH:GRATio? query.
Using the .verify(value) method will send the MEASUrement:MECH:GRATio? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:GRATio value command.

SCPI Syntax

- MEASUrement:MECH:GRATio <NR3>
- MEASUrement:MECH:GRATio?

Info

<NR3> specifies the gear ratio value for a specified measurement. The minimum and maximum values are 0.001 to 1000.

munits `property` ¶

munits: MeasurementMechMunits

Return the MEASUrement:MECH:MUNits command.

Description

This command sets or queries the global mechanical measurement results units.

Usage

Using the .query() method will send the MEASUrement:MECH:MUNits? query.
Using the .verify(value) method will send the MEASUrement:MECH:MUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:MUNits value command.

SCPI Syntax

- MEASUrement:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MECH:MUNits?

Info

NM specifies the results units of mechanical Torque measurement as NM.
OZINCH specifies the results units of mechanical Torque measurement as OZINCH.
FTLB specifies the results units of mechanical Torque measurement as FTLB.
INCHLB specifies the results units of mechanical Torque measurement as INCHLB.
DEGREES specifies the results units of mechanical Torque measurement as DEGREES.
RADIANS specifies the results units of mechanical Torque measurement as RADIANS.

ppairs `property` ¶

ppairs: MeasurementMechPpairs

Return the MEASUrement:MECH:PPAirs command.

Description

This command sets or queries the measurement number of pole pairs.

Usage

Using the .query() method will send the MEASUrement:MECH:PPAirs? query.
Using the .verify(value) method will send the MEASUrement:MECH:PPAirs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:PPAirs value command.

SCPI Syntax

- MEASUrement:MECH:PPAirs <NR1>
- MEASUrement:MECH:PPAirs?

Info

<NR1> defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.

pprotation `property` ¶

pprotation: MeasurementMechPprotation

Return the MEASUrement:MECH:PPRotation command.

Description

This command sets or queries the global pulses per rotation of the measurement.

Usage

Using the .query() method will send the MEASUrement:MECH:PPRotation? query.
Using the .verify(value) method will send the MEASUrement:MECH:PPRotation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:PPRotation value command.

SCPI Syntax

- MEASUrement:MECH:PPRotation <NR1>
- MEASUrement:MECH:PPRotation?

Info

<NR1> defines the pulses per rotation of the measurement. The minimum to maximum range is 1 to 100000.

source1 `property` ¶

source1: MeasurementMechSource1

Return the MEASUrement:MECH:SOUrce1 command.

Description

This command sets or queries the global mechanical source of the specified source number.

Usage

Using the .query() method will send the MEASUrement:MECH:SOUrce1? query.
Using the .verify(value) method will send the MEASUrement:MECH:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:SOUrce1 value command.

SCPI Syntax

- MEASUrement:MECH:SOUrce1 {CH<x>|MATH<x>|REF<x>|CH<x>_D<x>}
- MEASUrement:MECH:SOUrce1?

Info

CH<x> specifies an analog channel as the source waveform.
MATH<x> specifies a math waveform as the source waveform.
REF<x> specifies an reference waveform as the source waveform.
CH<x>_D<x> specifies a digital channel as the source waveform.

stype `property` ¶

stype: MeasurementMechStype

Return the MEASUrement:MECH:STYPe command.

Description

This command sets or queries the measurement sensor type.

Usage

Using the .query() method will send the MEASUrement:MECH:STYPe? query.
Using the .verify(value) method will send the MEASUrement:MECH:STYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:STYPe value command.

SCPI Syntax

- MEASUrement:MECH:STYPe {HSENSOR|QEI|RESOLVER}
- MEASUrement:MECH:STYPe?

Info

HSENSOR specifies the sensor type as HSENSOR.
QEI specifies the sensor type as QEI.
RESOLVER specifies the sensor type as RESOLVER.

MeasurementMechEindexz ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MECH:EINDexz command.

Description

This command sets or queries the global mechanical Index Z source.

Usage

Using the .query() method will send the MEASUrement:MECH:EINDexz? query.
Using the .verify(value) method will send the MEASUrement:MECH:EINDexz? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:EINDexz value command.

SCPI Syntax

- MEASUrement:MECH:EINDexz {ON|OFF|1|0}
- MEASUrement:MECH:EINDexz?

Info

ON specifies the Index Z check box state as enabled.
OFF specifies the Index Z check box state as disabled.
1 specifies the Index Z check box state as enabled.
0 specifies the Index Z check box state as disabled.

MeasurementMechGratio ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MECH:GRATio command.

Description

This command sets or queries the measurement gear ratio.

Usage

Using the .query() method will send the MEASUrement:MECH:GRATio? query.
Using the .verify(value) method will send the MEASUrement:MECH:GRATio? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:GRATio value command.

SCPI Syntax

- MEASUrement:MECH:GRATio <NR3>
- MEASUrement:MECH:GRATio?

Info

<NR3> specifies the gear ratio value for a specified measurement. The minimum and maximum values are 0.001 to 1000.

MeasurementMechMunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MECH:MUNits command.

Description

This command sets or queries the global mechanical measurement results units.

Usage

Using the .query() method will send the MEASUrement:MECH:MUNits? query.
Using the .verify(value) method will send the MEASUrement:MECH:MUNits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:MUNits value command.

SCPI Syntax

- MEASUrement:MECH:MUNits {NM|OZINCH|FTLB|INCHLB|DEGREES|RADIANS}
- MEASUrement:MECH:MUNits?

Info

NM specifies the results units of mechanical Torque measurement as NM.
OZINCH specifies the results units of mechanical Torque measurement as OZINCH.
FTLB specifies the results units of mechanical Torque measurement as FTLB.
INCHLB specifies the results units of mechanical Torque measurement as INCHLB.
DEGREES specifies the results units of mechanical Torque measurement as DEGREES.
RADIANS specifies the results units of mechanical Torque measurement as RADIANS.

MeasurementMechPpairs ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MECH:PPAirs command.

Description

This command sets or queries the measurement number of pole pairs.

Usage

Using the .query() method will send the MEASUrement:MECH:PPAirs? query.
Using the .verify(value) method will send the MEASUrement:MECH:PPAirs? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:PPAirs value command.

SCPI Syntax

- MEASUrement:MECH:PPAirs <NR1>
- MEASUrement:MECH:PPAirs?

Info

<NR1> defines the number of pole pairs for the specified measurement. The minimum to maximum range is 1 to 20.

MeasurementMechPprotation ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MECH:PPRotation command.

Description

This command sets or queries the global pulses per rotation of the measurement.

Usage

Using the .query() method will send the MEASUrement:MECH:PPRotation? query.
Using the .verify(value) method will send the MEASUrement:MECH:PPRotation? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:PPRotation value command.

SCPI Syntax

- MEASUrement:MECH:PPRotation <NR1>
- MEASUrement:MECH:PPRotation?

Info

<NR1> defines the pulses per rotation of the measurement. The minimum to maximum range is 1 to 100000.

MeasurementMechSource1 ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MECH:SOUrce1 command.

Description

This command sets or queries the global mechanical source of the specified source number.

Usage

Using the .query() method will send the MEASUrement:MECH:SOUrce1? query.
Using the .verify(value) method will send the MEASUrement:MECH:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:SOUrce1 value command.

SCPI Syntax

- MEASUrement:MECH:SOUrce1 {CH<x>|MATH<x>|REF<x>|CH<x>_D<x>}
- MEASUrement:MECH:SOUrce1?

Info

CH<x> specifies an analog channel as the source waveform.
MATH<x> specifies a math waveform as the source waveform.
REF<x> specifies an reference waveform as the source waveform.
CH<x>_D<x> specifies a digital channel as the source waveform.

MeasurementMechStype ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MECH:STYPe command.

Description

This command sets or queries the measurement sensor type.

Usage

Using the .query() method will send the MEASUrement:MECH:STYPe? query.
Using the .verify(value) method will send the MEASUrement:MECH:STYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MECH:STYPe value command.

SCPI Syntax

- MEASUrement:MECH:STYPe {HSENSOR|QEI|RESOLVER}
- MEASUrement:MECH:STYPe?

Info

HSENSOR specifies the sensor type as HSENSOR.
QEI specifies the sensor type as QEI.
RESOLVER specifies the sensor type as RESOLVER.

MeasurementMinui ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:MINUI command.

Description

This command sets or queries the minimum number of unit intervals required for BUJ analysis.

Usage

Using the .query() method will send the MEASUrement:MINUI? query.
Using the .verify(value) method will send the MEASUrement:MINUI? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:MINUI value command.

SCPI Syntax

- MEASUrement:MINUI <NR3>
- MEASUrement:MINUI?

Info

<NR3> is the minimum number of unit intervals required for BUJ analysis.

MeasurementPopulation ¶

Bases: SCPICmdRead

The MEASUrement:POPUlation command tree.

Usage

Using the .query() method will send the MEASUrement:POPUlation? query.
Using the .verify(value) method will send the MEASUrement:POPUlation? query and raise an AssertionError if the returned value does not match value.

Properties

.limit: The MEASUrement:POPUlation:LIMIT command tree.

limit `property` ¶

limit: MeasurementPopulationLimit

Return the MEASUrement:POPUlation:LIMIT command tree.

Usage

Using the .query() method will send the MEASUrement:POPUlation:LIMIT? query.
Using the .verify(value) method will send the MEASUrement:POPUlation:LIMIT? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.state: The MEASUrement:POPUlation:LIMIT:STATE command.
.value: The MEASUrement:POPUlation:LIMIT:VALue command.

MeasurementPopulationLimit ¶

Bases: SCPICmdRead

The MEASUrement:POPUlation:LIMIT command tree.

Usage

Using the .query() method will send the MEASUrement:POPUlation:LIMIT? query.
Using the .verify(value) method will send the MEASUrement:POPUlation:LIMIT? query and raise an AssertionError if the returned value does not match value.

Properties

.state: The MEASUrement:POPUlation:LIMIT:STATE command.
.value: The MEASUrement:POPUlation:LIMIT:VALue command.

state `property` ¶

state: MeasurementPopulationLimitState

Return the MEASUrement:POPUlation:LIMIT:STATE command.

Description

This command sets or queries the global population limit state for the measurement.

Usage

Using the .query() method will send the MEASUrement:POPUlation:LIMIT:STATE? query.
Using the .verify(value) method will send the MEASUrement:POPUlation:LIMIT:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:POPUlation:LIMIT:STATE value command.

SCPI Syntax

- MEASUrement:POPUlation:LIMIT:STATE {OFF|ON|0|1 }
- MEASUrement:POPUlation:LIMIT:STATE?

Info

OFF turns off the population limit.
ON turns on the population limit.
0 turns off the population limit.
1 turns on the population limit.

value `property` ¶

value: MeasurementPopulationLimitValue

Return the MEASUrement:POPUlation:LIMIT:VALue command.

Description

This command sets or queries the global population limit value for the measurement.

Usage

Using the .query() method will send the MEASUrement:POPUlation:LIMIT:VALue? query.
Using the .verify(value) method will send the MEASUrement:POPUlation:LIMIT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:POPUlation:LIMIT:VALue value command.

SCPI Syntax

- MEASUrement:POPUlation:LIMIT:VALue <NR1>
- MEASUrement:POPUlation:LIMIT:VALue?

Info

<NR1> is the current limit value.

MeasurementPopulationLimitState ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:POPUlation:LIMIT:STATE command.

Description

This command sets or queries the global population limit state for the measurement.

Usage

Using the .query() method will send the MEASUrement:POPUlation:LIMIT:STATE? query.
Using the .verify(value) method will send the MEASUrement:POPUlation:LIMIT:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:POPUlation:LIMIT:STATE value command.

SCPI Syntax

- MEASUrement:POPUlation:LIMIT:STATE {OFF|ON|0|1 }
- MEASUrement:POPUlation:LIMIT:STATE?

Info

OFF turns off the population limit.
ON turns on the population limit.
0 turns off the population limit.
1 turns on the population limit.

MeasurementPopulationLimitValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:POPUlation:LIMIT:VALue command.

Description

This command sets or queries the global population limit value for the measurement.

Usage

Using the .query() method will send the MEASUrement:POPUlation:LIMIT:VALue? query.
Using the .verify(value) method will send the MEASUrement:POPUlation:LIMIT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:POPUlation:LIMIT:VALue value command.

SCPI Syntax

- MEASUrement:POPUlation:LIMIT:VALue <NR1>
- MEASUrement:POPUlation:LIMIT:VALue?

Info

<NR1> is the current limit value.

MeasurementRefItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The MEASUrement:REF<x> command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>? query.
Using the .verify(value) method will send the MEASUrement:REF<x>? query and raise an AssertionError if the returned value does not match value.

Properties

.reflevels: The MEASUrement:REF<x>:REFLevels command tree.

reflevels `property` ¶

reflevels: MeasurementRefItemReflevels

Return the MEASUrement:REF<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.absolute: The MEASUrement:REF<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REF<x>:REFLevels:BASETop command.
.method: The MEASUrement:REF<x>:REFLevels:METHod command.
.percent: The MEASUrement:REF<x>:REFLevels:PERCent command tree.

MeasurementRefItemReflevels ¶

Bases: SCPICmdRead

The MEASUrement:REF<x>:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels? query and raise an AssertionError if the returned value does not match value.

Properties

.absolute: The MEASUrement:REF<x>:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REF<x>:REFLevels:BASETop command.
.method: The MEASUrement:REF<x>:REFLevels:METHod command.
.percent: The MEASUrement:REF<x>:REFLevels:PERCent command tree.

absolute `property` ¶

absolute: MeasurementRefItemReflevelsAbsolute

Return the MEASUrement:REF<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementRefItemReflevelsBasetop

Return the MEASUrement:REF<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REF<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

method `property` ¶

method: MeasurementRefItemReflevelsMethod

Return the MEASUrement:REF<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REF<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REF<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

percent `property` ¶

percent: MeasurementRefItemReflevelsPercent

Return the MEASUrement:REF<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

MeasurementRefItemReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementRefItemReflevelsAbsoluteFallhigh

Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

falllow `property` ¶

falllow: MeasurementRefItemReflevelsAbsoluteFalllow

Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

fallmid `property` ¶

fallmid: MeasurementRefItemReflevelsAbsoluteFallmid

Return the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

hysteresis `property` ¶

hysteresis: MeasurementRefItemReflevelsAbsoluteHysteresis

Return the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

risehigh `property` ¶

risehigh: MeasurementRefItemReflevelsAbsoluteRisehigh

Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

riselow `property` ¶

riselow: MeasurementRefItemReflevelsAbsoluteRiselow

Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

risemid `property` ¶

risemid: MeasurementRefItemReflevelsAbsoluteRisemid

Return the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

type `property` ¶

type: MeasurementRefItemReflevelsAbsoluteType

Return the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementRefItemReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

MeasurementRefItemReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REF<x>:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementRefItemReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REF<x>:REFLevels:BASETop?

Info

AUTO automatically chooses a reference level method.
MINMax specifies that reference levels are relative to the measurement MIN and MAX.
MEANhistogram specifies that reference levels are relative to the histogram mean BASE and TOP.
MODEhistogram specifies that reference levels are relative to the histogram mode BASE and TOP.
EYEhistogram specifies that reverence levels are relative to the eye histogram BASE and TOP.

MeasurementRefItemReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REF<x>:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REF<x>:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REF<x>:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementRefItemReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementRefItemReflevelsPercentFallhigh

Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

falllow `property` ¶

falllow: MeasurementRefItemReflevelsPercentFalllow

Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the low reference level.

fallmid `property` ¶

fallmid: MeasurementRefItemReflevelsPercentFallmid

Return the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

hysteresis `property` ¶

hysteresis: MeasurementRefItemReflevelsPercentHysteresis

Return the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 99% is equal to MAX and 1% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

risehigh `property` ¶

risehigh: MeasurementRefItemReflevelsPercentRisehigh

Return the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

riselow `property` ¶

riselow: MeasurementRefItemReflevelsPercentRiselow

Return the MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

risemid `property` ¶

risemid: MeasurementRefItemReflevelsPercentRisemid

Return the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

type `property` ¶

type: MeasurementRefItemReflevelsPercentType

Return the MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementRefItemReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

MeasurementRefItemReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the low reference level.

MeasurementRefItemReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

MeasurementRefItemReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 99% is equal to MAX and 1% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

MeasurementRefItemReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

MeasurementRefItemReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

MeasurementRefItemReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REF<x>:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

MeasurementRefItemReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REF<x>:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REF<x>:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REF<x>:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REF<x>:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementReflevels ¶

Bases: SCPICmdRead

The MEASUrement:REFLevels command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels? query.
Using the .verify(value) method will send the MEASUrement:REFLevels? query and raise an AssertionError if the returned value does not match value.

Properties

.absolute: The MEASUrement:REFLevels:ABSolute command tree.
.basetop: The MEASUrement:REFLevels:BASETop command.
.jittermode: The MEASUrement:REFLevels:JITTERMODE command.
.method: The MEASUrement:REFLevels:METHod command.
.mode: The MEASUrement:REFLevels:MODE command.
.percent: The MEASUrement:REFLevels:PERCent command tree.
.type: The MEASUrement:REFLevels:TYPE command.

absolute `property` ¶

absolute: MeasurementReflevelsAbsolute

Return the MEASUrement:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REFLevels:ABSolute:TYPE command.

basetop `property` ¶

basetop: MeasurementReflevelsBasetop

Return the MEASUrement:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?

Info

AUTO sets the base top method to AUTO.
MINMax sets the base top method to MINMax.
MEANhistogram sets the base top method to MEANhistogram.
MODEhistogram sets the base top method to MODEhistogram.
EYEhistogram sets the base top method to EYEhistogram.

jittermode `property` ¶

jittermode: MeasurementReflevelsJittermode

Return the MEASUrement:REFLevels:JITTERMODE command.

Description

This command sets or queries how often reference levels are calculated on Jitter measurements. If the mode is set to Latch, ref levels are calculated only on the first acquisition after a statistics reset. If it is set to Continuous, reference levels are calculated on every acquisition.

Usage

Using the .query() method will send the MEASUrement:REFLevels:JITTERMODE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:JITTERMODE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:JITTERMODE value command.

SCPI Syntax

- MEASUrement:REFLevels:JITTERMODE {CONTinuous|LATCh}
- MEASUrement:REFLevels:JITTERMODE?

Info

CONTinuous specifies that reference levels are calculated on every acquisition.
LATCh specifies that reference levels are calculated only on the first acquisition after a statistics reset.

method `property` ¶

method: MeasurementReflevelsMethod

Return the MEASUrement:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REFLevels:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REFLevels:REFLevel:ABSolute commands. This method is useful when precise values are required.

mode `property` ¶

mode: MeasurementReflevelsMode

Return the MEASUrement:REFLevels:MODE command.

Description

This command sets or queries how often reference levels are calculated.

Usage

Using the .query() method will send the MEASUrement:REFLevels:MODE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:MODE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:MODE value command.

SCPI Syntax

- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?

Info

LATCh calculates reference levels only on the first acquisition after a statistics reset.
CONTinuous calculates reference levels on every acquisition.

percent `property` ¶

percent: MeasurementReflevelsPercent

Return the MEASUrement:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.fallhigh: The MEASUrement:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REFLevels:PERCent:TYPE command.

type `property` ¶

type: MeasurementReflevelsType

Return the MEASUrement:REFLevels:TYPE command.

Description

This command sets or queries the shared reference level method used for sources of measurement calculations.

Usage

Using the .query() method will send the MEASUrement:REFLevels:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?

Info

GLOBal shares reference levels across measurements.
PERSource causes reference levels to be used on individual measurements.

MeasurementReflevelsAbsolute ¶

Bases: SCPICmdRead

The MEASUrement:REFLevels:ABSolute command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REFLevels:ABSolute:FALLHigh command.
.falllow: The MEASUrement:REFLevels:ABSolute:FALLLow command.
.fallmid: The MEASUrement:REFLevels:ABSolute:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:ABSolute:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:ABSolute:RISEHigh command.
.riselow: The MEASUrement:REFLevels:ABSolute:RISELow command.
.risemid: The MEASUrement:REFLevels:ABSolute:RISEMid command.
.type: The MEASUrement:REFLevels:ABSolute:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementReflevelsAbsoluteFallhigh

Return the MEASUrement:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

falllow `property` ¶

falllow: MeasurementReflevelsAbsoluteFalllow

Return the MEASUrement:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge.

fallmid `property` ¶

fallmid: MeasurementReflevelsAbsoluteFallmid

Return the MEASUrement:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge.

hysteresis `property` ¶

hysteresis: MeasurementReflevelsAbsoluteHysteresis

Return the MEASUrement:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level.

risehigh `property` ¶

risehigh: MeasurementReflevelsAbsoluteRisehigh

Return the MEASUrement:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge.

riselow `property` ¶

riselow: MeasurementReflevelsAbsoluteRiselow

Return the MEASUrement:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the low reference level of the rising edge.

risemid `property` ¶

risemid: MeasurementReflevelsAbsoluteRisemid

Return the MEASUrement:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge.

type `property` ¶

type: MeasurementReflevelsAbsoluteType

Return the MEASUrement:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementReflevelsAbsoluteFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:FALLHigh command.

Description

This command sets or queries the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLHigh <NR3>
- MEASUrement:REFLevels:ABSolute:FALLHigh?

Info

<NR3> is the value used as the high reference level of the falling edge when the measurement’s ref level method is set to absolute.

MeasurementReflevelsAbsoluteFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:FALLLow command.

Description

This command sets or queries the value used as the low reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLLow <NR3>
- MEASUrement:REFLevels:ABSolute:FALLLow?

Info

<NR3> is the value used as the low reference level of the falling edge.

MeasurementReflevelsAbsoluteFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:FALLMid command.

Description

This command sets or queries the value used as the mid reference level of the falling edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:FALLMid <NR3>
- MEASUrement:REFLevels:ABSolute:FALLMid?

Info

<NR3> is the value used as the mid reference level of the falling edge.

MeasurementReflevelsAbsoluteHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:HYSTeresis command.

Description

This command sets or queries the value of the hysteresis of the reference level when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:HYSTeresis <NR3>
- MEASUrement:REFLevels:ABSolute:HYSTeresis?

Info

<NR3> is the value of the hysteresis of the reference level.

MeasurementReflevelsAbsoluteRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:RISEHigh command.

Description

This command sets or queries the value used as the high reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEHigh <NR3>
- MEASUrement:REFLevels:ABSolute:RISEHigh?

Info

<NR3> is the value used as the high reference level of the rising edge.

MeasurementReflevelsAbsoluteRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:RISELow command.

Description

This command sets or queries the value used as the low reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISELow <NR3>
- MEASUrement:REFLevels:ABSolute:RISELow?

Info

<NR3> is the value used as the low reference level of the rising edge.

MeasurementReflevelsAbsoluteRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:RISEMid command.

Description

This command sets or queries the value used as the mid reference level of the rising edge when the measurement’s ref level method is set to absolute.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:RISEMid <NR3>
- MEASUrement:REFLevels:ABSolute:RISEMid?

Info

<NR3> is the mid reference level of the rising edge.

MeasurementReflevelsAbsoluteType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:ABSolute:TYPE command.

Description

This command sets or queries the reference level type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:ABSolute:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:ABSolute:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:ABSolute:TYPE {SAME|UNIQue}
- MEASUrement:REFLevels:ABSolute:TYPE?

Info

SAME specifies that the absolute levels are set the same.
UNIQue specifies that the absolute levels can be set independently.

MeasurementReflevelsBasetop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:BASETop command.

Description

This command sets or queries the method used to calculate the TOP and BASE, used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:BASETop? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:BASETop? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:BASETop value command.

SCPI Syntax

- MEASUrement:REFLevels:BASETop {AUTO|MINMax|MEANhistogram|MODEhistogram|EYEhistogram}
- MEASUrement:REFLevels:BASETop?

Info

AUTO sets the base top method to AUTO.
MINMax sets the base top method to MINMax.
MEANhistogram sets the base top method to MEANhistogram.
MODEhistogram sets the base top method to MODEhistogram.
EYEhistogram sets the base top method to EYEhistogram.

MeasurementReflevelsJittermode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:JITTERMODE command.

Description

This command sets or queries how often reference levels are calculated on Jitter measurements. If the mode is set to Latch, ref levels are calculated only on the first acquisition after a statistics reset. If it is set to Continuous, reference levels are calculated on every acquisition.

Usage

Using the .query() method will send the MEASUrement:REFLevels:JITTERMODE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:JITTERMODE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:JITTERMODE value command.

SCPI Syntax

- MEASUrement:REFLevels:JITTERMODE {CONTinuous|LATCh}
- MEASUrement:REFLevels:JITTERMODE?

Info

CONTinuous specifies that reference levels are calculated on every acquisition.
LATCh specifies that reference levels are calculated only on the first acquisition after a statistics reset.

MeasurementReflevelsMethod ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:METHod command.

Description

This command sets or queries the method used to calculate reference levels for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:METHod? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:METHod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:METHod value command.

SCPI Syntax

- MEASUrement:REFLevels:METHod {PERCent|ABSolute}
- MEASUrement:REFLevels:METHod?

Info

PERCent specifies that the reference levels are calculated as a percent relative to HIGH and LOW. The percentages are defined using the MEASUrement:REFLevels:REFLevel:PERCent commands.
ABSolute specifies that the reference levels are set explicitly using the MEASUrement:REFLevels:REFLevel:ABSolute commands. This method is useful when precise values are required.

MeasurementReflevelsMode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:MODE command.

Description

This command sets or queries how often reference levels are calculated.

Usage

Using the .query() method will send the MEASUrement:REFLevels:MODE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:MODE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:MODE value command.

SCPI Syntax

- MEASUrement:REFLevels:MODE {LATCh|CONTinuous}
- MEASUrement:REFLevels:MODE?

Info

LATCh calculates reference levels only on the first acquisition after a statistics reset.
CONTinuous calculates reference levels on every acquisition.

MeasurementReflevelsPercent ¶

Bases: SCPICmdRead

The MEASUrement:REFLevels:PERCent command tree.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent? query and raise an AssertionError if the returned value does not match value.

Properties

.fallhigh: The MEASUrement:REFLevels:PERCent:FALLHigh command.
.falllow: The MEASUrement:REFLevels:PERCent:FALLLow command.
.fallmid: The MEASUrement:REFLevels:PERCent:FALLMid command.
.hysteresis: The MEASUrement:REFLevels:PERCent:HYSTeresis command.
.risehigh: The MEASUrement:REFLevels:PERCent:RISEHigh command.
.riselow: The MEASUrement:REFLevels:PERCent:RISELow command.
.risemid: The MEASUrement:REFLevels:PERCent:RISEMid command.
.type: The MEASUrement:REFLevels:PERCent:TYPE command.

fallhigh `property` ¶

fallhigh: MeasurementReflevelsPercentFallhigh

Return the MEASUrement:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

falllow `property` ¶

falllow: MeasurementReflevelsPercentFalllow

Return the MEASUrement:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

fallmid `property` ¶

fallmid: MeasurementReflevelsPercentFallmid

Return the MEASUrement:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

hysteresis `property` ¶

hysteresis: MeasurementReflevelsPercentHysteresis

Return the MEASUrement:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 1% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

risehigh `property` ¶

risehigh: MeasurementReflevelsPercentRisehigh

Return the MEASUrement:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

riselow `property` ¶

riselow: MeasurementReflevelsPercentRiselow

Return the MEASUrement:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

risemid `property` ¶

risemid: MeasurementReflevelsPercentRisemid

Return the MEASUrement:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

type `property` ¶

type: MeasurementReflevelsPercentType

Return the MEASUrement:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementReflevelsPercentFallhigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:FALLHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLHigh <NR3>
- MEASUrement:REFLevels:PERCent:FALLHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the falling edge.

MeasurementReflevelsPercentFalllow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:FALLLow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLLow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLLow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLLow <NR3>
- MEASUrement:REFLevels:PERCent:FALLLow?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

MeasurementReflevelsPercentFallmid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:FALLMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the falling edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:FALLMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:FALLMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:FALLMid <NR3>
- MEASUrement:REFLevels:PERCent:FALLMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the falling edge.

MeasurementReflevelsPercentHysteresis ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:HYSTeresis command.

Description

This command sets or queries the percentage (where 100% is equal to MAX and 1% is equal to MIN) used to calculate the hysteresis of the reference level when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:HYSTeresis value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:HYSTeresis <NR3>
- MEASUrement:REFLevels:PERCent:HYSTeresis?

Info

<NR3> is the percentage used to calculate the hysteresis of the reference level.

MeasurementReflevelsPercentRisehigh ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:RISEHigh command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the high reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEHigh value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEHigh <NR3>
- MEASUrement:REFLevels:PERCent:RISEHigh?

Info

<NR3> is the percentage used to calculate the high reference level of the rising edge.

MeasurementReflevelsPercentRiselow ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:RISELow command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the low reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISELow? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISELow? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISELow value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISELow <NR3>
- MEASUrement:REFLevels:PERCent:RISELow?

Info

<NR3> is the percentage used to calculate the low reference level of the rising edge.

MeasurementReflevelsPercentRisemid ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:RISEMid command.

Description

This command sets or queries the percentage (where 99% is equal to TOP and 1% is equal to BASE) used to calculate the mid reference level of the rising edge when the measurement’s ref level method is set to percent.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:RISEMid? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:RISEMid value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:RISEMid <NR3>
- MEASUrement:REFLevels:PERCent:RISEMid?

Info

<NR3> is the percentage used to calculate the mid reference level of the rising edge.

MeasurementReflevelsPercentType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:PERCent:TYPE command.

Description

This command sets or queries the reference level percent type for the measurement.

Usage

Using the .query() method will send the MEASUrement:REFLevels:PERCent:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:PERCent:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:PERCent:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:PERCent:TYPE {TENNinety|TWENtyeighty|CUSTom}
- MEASUrement:REFLevels:PERCent:TYPE?

Info

TENNinety sets the values for Low, Mid and High Ref to 10%, 50% and 90% respectively.
TWENtyeighty sets the values for Low, Mid and High Ref are set to 20%, 50% and 80% respectively.
CUSTom allows setting other reference level percents.

MeasurementReflevelsType ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:REFLevels:TYPE command.

Description

This command sets or queries the shared reference level method used for sources of measurement calculations.

Usage

Using the .query() method will send the MEASUrement:REFLevels:TYPE? query.
Using the .verify(value) method will send the MEASUrement:REFLevels:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:REFLevels:TYPE value command.

SCPI Syntax

- MEASUrement:REFLevels:TYPE {GLOBal|PERSource}
- MEASUrement:REFLevels:TYPE?

Info

GLOBal shares reference levels across measurements.
PERSource causes reference levels to be used on individual measurements.

MeasurementResults ¶

Bases: SCPICmdRead

The MEASUrement:RESUlts command tree.

Usage

Using the .query() method will send the MEASUrement:RESUlts? query.
Using the .verify(value) method will send the MEASUrement:RESUlts? query and raise an AssertionError if the returned value does not match value.

Properties

.history: The MEASUrement:RESUlts:HISTory command tree.

history `property` ¶

history: MeasurementResultsHistory

Return the MEASUrement:RESUlts:HISTory command tree.

Usage

Using the .query() method will send the MEASUrement:RESUlts:HISTory? query.
Using the .verify(value) method will send the MEASUrement:RESUlts:HISTory? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.start: The MEASUrement:RESUlts:HISTory:STARt command.
.stop: The MEASUrement:RESUlts:HISTory:STOP command.

MeasurementResultsHistory ¶

Bases: SCPICmdRead

The MEASUrement:RESUlts:HISTory command tree.

Usage

Using the .query() method will send the MEASUrement:RESUlts:HISTory? query.
Using the .verify(value) method will send the MEASUrement:RESUlts:HISTory? query and raise an AssertionError if the returned value does not match value.

Properties

.start: The MEASUrement:RESUlts:HISTory:STARt command.
.stop: The MEASUrement:RESUlts:HISTory:STOP command.

start `property` ¶

start: MeasurementResultsHistoryStart

Return the MEASUrement:RESUlts:HISTory:STARt command.

Description

This command sets or queries the starting acquisition number for transferring measurement history results.

Usage

Using the .query() method will send the MEASUrement:RESUlts:HISTory:STARt? query.
Using the .verify(value) method will send the MEASUrement:RESUlts:HISTory:STARt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:RESUlts:HISTory:STARt value command.

SCPI Syntax

- MEASUrement:RESUlts:HISTory:STARt <NR1>
- MEASUrement:RESUlts:HISTory:STARt?

Info

<NR1> is the first acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred from acquisitions to MEASUrement:RESUlts:HISTory:STOP.

stop `property` ¶

stop: MeasurementResultsHistoryStop

Return the MEASUrement:RESUlts:HISTory:STOP command.

Description

This command sets or queries the last acquisition number that will be transferred for measurement history results.

Usage

Using the .query() method will send the MEASUrement:RESUlts:HISTory:STOP? query.
Using the .verify(value) method will send the MEASUrement:RESUlts:HISTory:STOP? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:RESUlts:HISTory:STOP value command.

SCPI Syntax

- MEASUrement:RESUlts:HISTory:STOP <NR1>
- MEASUrement:RESUlts:HISTory:STOP?

Info

<NR1> is the last acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred from MEASUrement:RESUlts:HISTory:STARt to . A special value of 0 for indicates that the stop position is always the last history acquisition.

MeasurementResultsHistoryStart ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:RESUlts:HISTory:STARt command.

Description

This command sets or queries the starting acquisition number for transferring measurement history results.

Usage

Using the .query() method will send the MEASUrement:RESUlts:HISTory:STARt? query.
Using the .verify(value) method will send the MEASUrement:RESUlts:HISTory:STARt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:RESUlts:HISTory:STARt value command.

SCPI Syntax

- MEASUrement:RESUlts:HISTory:STARt <NR1>
- MEASUrement:RESUlts:HISTory:STARt?

Info

<NR1> is the first acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred from acquisitions to MEASUrement:RESUlts:HISTory:STOP.

MeasurementResultsHistoryStop ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:RESUlts:HISTory:STOP command.

Description

This command sets or queries the last acquisition number that will be transferred for measurement history results.

Usage

Using the .query() method will send the MEASUrement:RESUlts:HISTory:STOP? query.
Using the .verify(value) method will send the MEASUrement:RESUlts:HISTory:STOP? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:RESUlts:HISTory:STOP value command.

SCPI Syntax

- MEASUrement:RESUlts:HISTory:STOP <NR1>
- MEASUrement:RESUlts:HISTory:STOP?

Info

<NR1> is the last acquisition that will be transferred, which ranges from 1 to the number of history acquisitions. Results will be transferred from MEASUrement:RESUlts:HISTory:STARt to . A special value of 0 for indicates that the stop position is always the last history acquisition.

MeasurementStatistics ¶

Bases: SCPICmdRead

The MEASUrement:STATIstics command tree.

Usage

Using the .query() method will send the MEASUrement:STATIstics? query.
Using the .verify(value) method will send the MEASUrement:STATIstics? query and raise an AssertionError if the returned value does not match value.

Properties

.cyclemode: The MEASUrement:STATIstics:CYCLEMode command.

cyclemode `property` ¶

cyclemode: MeasurementStatisticsCyclemode

Return the MEASUrement:STATIstics:CYCLEMode command.

Description

This command turns on and off cycle to cycle measurement statistics tracking and affects computation and display of cycle-cycle statistics in the Measurement Result table. It affects measurement statistics after being enabled and after new data is acquired and measured.

Usage

Using the .query() method will send the MEASUrement:STATIstics:CYCLEMode? query.
Using the .verify(value) method will send the MEASUrement:STATIstics:CYCLEMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:STATIstics:CYCLEMode value command.

SCPI Syntax

- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?

Info

OFF turns off statistics for all measurements. This is the default value.
ON turns on statistics and displays all statistics for each measurement.
0 turns off statistics for all measurements.
1 turns on statistics and displays all statistics for each measurement.

MeasurementStatisticsCyclemode ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:STATIstics:CYCLEMode command.

Description

This command turns on and off cycle to cycle measurement statistics tracking and affects computation and display of cycle-cycle statistics in the Measurement Result table. It affects measurement statistics after being enabled and after new data is acquired and measured.

Usage

Using the .query() method will send the MEASUrement:STATIstics:CYCLEMode? query.
Using the .verify(value) method will send the MEASUrement:STATIstics:CYCLEMode? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:STATIstics:CYCLEMode value command.

SCPI Syntax

- MEASUrement:STATIstics:CYCLEMode {ON|OFF|1|0}
- MEASUrement:STATIstics:CYCLEMode?

Info

OFF turns off statistics for all measurements. This is the default value.
ON turns on statistics and displays all statistics for each measurement.
0 turns off statistics for all measurements.
1 turns on statistics and displays all statistics for each measurement.

MeasurementWbg ¶

Bases: SCPICmdRead

The MEASUrement:WBG command tree.

Usage

Using the .query() method will send the MEASUrement:WBG? query.
Using the .verify(value) method will send the MEASUrement:WBG? query and raise an AssertionError if the returned value does not match value.

Properties

.pdevice: The MEASUrement:WBG:PDEVice command.

pdevice `property` ¶

pdevice: MeasurementWbgPdevice

Return the MEASUrement:WBG:PDEVice command.

Description

This command sets or returns the type of the Power device.

Usage

Using the .query() method will send the MEASUrement:WBG:PDEVice? query.
Using the .verify(value) method will send the MEASUrement:WBG:PDEVice? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:WBG:PDEVice value command.

SCPI Syntax

- MEASUrement:WBG:PDEVice {IGBT|MOSFET}
- MEASUrement:WBG:PDEVice?

Info

IGBT specifies the type of the Power device as IGBT.
MOSFET specifies the type of the Power device as MOSFET.

MeasurementWbgPdevice ¶

Bases: SCPICmdWrite, SCPICmdRead

The MEASUrement:WBG:PDEVice command.

Description

This command sets or returns the type of the Power device.

Usage

Using the .query() method will send the MEASUrement:WBG:PDEVice? query.
Using the .verify(value) method will send the MEASUrement:WBG:PDEVice? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the MEASUrement:WBG:PDEVice value command.

SCPI Syntax

- MEASUrement:WBG:PDEVice {IGBT|MOSFET}
- MEASUrement:WBG:PDEVice?

Info

IGBT specifies the type of the Power device as IGBT.
MOSFET specifies the type of the Power device as MOSFET.

measurement ¶

Measurement ¶

addmeas property ¶

addnew property ¶

annotate property ¶

autoset property ¶

ch property ¶

clockrecovery property ¶

ddjmethod property ¶

delete property ¶

deleteall property ¶

diracmodel property ¶

displayunits property ¶

edge property ¶

enablepjitter property ¶

eyerender property ¶

filters property ¶

gating property ¶

highlevel property ¶

interp property ¶

jittermodel property ¶

list property ¶

lockrj property ¶

lockrjvalue property ¶

math property ¶

meas property ¶

measrange property ¶

mech property ¶

minui property ¶

population property ¶

ref property ¶

reflevels property ¶

results property ¶

statistics property ¶

wbg property ¶

MeasurementAddmeas ¶

MeasurementAddnew ¶

MeasurementAnnotate ¶

MeasurementAutoset ¶

MeasurementChannel ¶

reflevels property ¶

MeasurementChannelReflevels ¶

absolute property ¶

basetop property ¶

method property ¶

percent property ¶

MeasurementChannelReflevelsAbsolute ¶

fallhigh property ¶

falllow property ¶

fallmid property ¶

hysteresis property ¶

risehigh property ¶

riselow property ¶

risemid property ¶

type property ¶

MeasurementChannelReflevelsAbsoluteFallhigh ¶

MeasurementChannelReflevelsAbsoluteFalllow ¶

MeasurementChannelReflevelsAbsoluteFallmid ¶

MeasurementChannelReflevelsAbsoluteHysteresis ¶

MeasurementChannelReflevelsAbsoluteRisehigh ¶

MeasurementChannelReflevelsAbsoluteRiselow ¶

MeasurementChannelReflevelsAbsoluteRisemid ¶

MeasurementChannelReflevelsAbsoluteType ¶

MeasurementChannelReflevelsBasetop ¶

MeasurementChannelReflevelsMethod ¶

MeasurementChannelReflevelsPercent ¶

fallhigh property ¶

falllow property ¶

fallmid property ¶

hysteresis property ¶

risehigh property ¶

riselow property ¶

risemid property ¶

type property ¶

MeasurementChannelReflevelsPercentFallhigh ¶

MeasurementChannelReflevelsPercentFalllow ¶

MeasurementChannelReflevelsPercentFallmid ¶

MeasurementChannelReflevelsPercentHysteresis ¶

MeasurementChannelReflevelsPercentRisehigh ¶

MeasurementChannelReflevelsPercentRiselow ¶

addmeas `property` ¶

addnew `property` ¶

annotate `property` ¶

autoset `property` ¶

ch `property` ¶

clockrecovery `property` ¶

ddjmethod `property` ¶

delete `property` ¶

deleteall `property` ¶

diracmodel `property` ¶

displayunits `property` ¶

edge `property` ¶

enablepjitter `property` ¶

eyerender `property` ¶

filters `property` ¶

gating `property` ¶

highlevel `property` ¶

interp `property` ¶

jittermodel `property` ¶

list `property` ¶

lockrj `property` ¶

lockrjvalue `property` ¶

math `property` ¶

meas `property` ¶

measrange `property` ¶

mech `property` ¶

minui `property` ¶

population `property` ¶

ref `property` ¶

reflevels `property` ¶

results `property` ¶

statistics `property` ¶

wbg `property` ¶

reflevels `property` ¶

absolute `property` ¶

basetop `property` ¶

method `property` ¶

percent `property` ¶

fallhigh `property` ¶

falllow `property` ¶

fallmid `property` ¶

hysteresis `property` ¶

risehigh `property` ¶

riselow `property` ¶

risemid `property` ¶

type `property` ¶

fallhigh `property` ¶

falllow `property` ¶

fallmid `property` ¶

hysteresis `property` ¶

risehigh `property` ¶

riselow `property` ¶

risemid `property` ¶

type `property` ¶

advanced `property` ¶

clockfrequency `property` ¶

clockmultiplier `property` ¶

constclockmode `property` ¶

damping `property` ¶

datapath `property` ¶

datarate `property` ¶

explicitclockmode `property` ¶

jtfbandwidth `property` ¶

loopbandwidth `property` ¶

meanautocalculate `property` ¶

method `property` ¶

model `property` ¶

nominaloffset `property` ¶

standard `property` ¶

tdcompensation `property` ¶

method `property` ¶

selectiontype `property` ¶

blankingtime `property` ¶

highpass `property` ¶

lowpass `property` ¶

ramptime `property` ¶

freq `property` ¶

spec `property` ¶

freq `property` ¶

spec `property` ¶