[python source code]

dpojet

The dpojet commands module.

These commands are used in the following models: DPO5KB, DPO70KC, DPO70KD, DPO70KDX, DPO70KSX, DPO7KC, DSA70KC, DSA70KD, MSO5KB, MSO70KC, MSO70KDX

THIS FILE IS AUTO-GENERATED, IT SHOULD NOT BE MANUALLY MODIFIED.

Please report an issue if one is found.

Commands and Queries 
- DPOJET:ACTIVATE
- DPOJET:ADDMeas {PERIod|CCPeriod|FREQuency|NPERiod|PWIdth|NWIdth|PDUTy|NDUTy|PCCDuty|NCCDuty|DATARATE|TIE|RJ|RJDirac|TJber|DJ|DJDirac|PHASENoise|DCD|DDJ|PJ|J2|J9|SRJ|PJrms|SJFREQ|PKPKCLKTJ|PKPKCLKRJ|PKPKCLKDJ|PJRMS|FN|RJH|RJV|PJH|PJV|RN|RNV|RNH|DN|DDN|DDN_1|DDN_0|PN|PNV|PNH|NPN|TNBER|NOISESUMMARY|UNITAMPLITUDE|RISEtime|SETup|HIGHTime|FALLtime|HOLD|LOWTime|SKEW|GATEDSKEW|HEIght|WIDth|MASKHits|WIDTHBer|HEIGHTBer|CYCLEMIN|CYCLEMAX|ACRMS|ACCOMmonmode|COMmonmode|HIGH|TNTratio|HIGHLOW|LOW|VDIFFxovr|RISESLEWrate|FALLSLEWrate|OVERShoot|UNDERShoot|CYCLEPktopk|JITTERSummary|PCIETTXDiffpp|PCIEDEemph|PCIETTx|PCIETTXRise|PCIETTXFall|PCIEUI|PCIETMinpulse|PCIEMEdmxjitter|PCIETRfmismch|PCIESSCFReqdev|PCIEMAXMINratio|PCIESSCPROFile|PCIEVEye|PCIETTXUTJ|PCIETTXUDJDD|PCIETTXUPWTJ|PCIETTXUPWDJDD|PCIETTXDDJ|PCIEVTXBOOST|PCIEVTXNOEQ|PCIEVTXEIEOS|PCIEPS21TX|PCIEACCommonmode|VTXDiffpp|TMINPULSETJ|TCDRslewmax|USBUI|USBACCommonmode|TMINPULSEDJ|QFACTOR|EYELOW|EYEHIGH|TCMDTOCMD|TIMEOUTSIDELEVEL|SSCFREQDEVMAX|SSCFREQDEVMIN|SSCFREQDEV|SSCMODrate|SSCPROfile|USBSSCFREQDEVMAX|USBSSCFREQDEVMIN|USBSSCMODrate|USBSSCPROFile|AUTOFITMaskhits|AOP|EXRATIO|OMA|OPTHIGH|OPTLOW|EYECROSSLEVEL|EYECROSSTIME|EYECROSSPERCENT|DFEEW|DFEEH|DFEEYEDIAGRAM|VWOE|MASKMARGIN|MASKHITRATIO|RIN|RINXOMA|TDEC }
- DPOJET:ADDPlot {TIMEtrend|DATAarray|HISTOgram|SPECtrum|TRANSfer|PHASEnoise|EYE|WAVEform|BATHtub|QBathtub|QPulsewidth|COMPOSITEJitterhist|NOISEBAthtub|BERContour|CORRELATEDEye|PDFEye|BEREye|COMPOSITENoisehist}, MEAS<x>
- DPOJET:ANALYSISMETHOD { JITTEROnly|JITTERNoise }
- DPOJET:ANALYSISMETHOD?
- DPOJET:APPLYAll {FILTers|CLOCKRecovery|RJDJ}, MEAS<x>
- DPOJET:BITRatestate {0|1}
- DPOJET:BITRatestate?
- DPOJET:CLEARALLMeas
- DPOJET:CLEARALLPlots
- DPOJET:DATAratelimits <NR3>
- DPOJET:DATAratelimits?
- DPOJET:DESKEW {EXEcute}
- DPOJET:DESKEW:DESKEWHysteresis <NR3>
- DPOJET:DESKEW:DESKEWHysteresis?
- DPOJET:DESKEW:DESKEWMidlevel <NR3>
- DPOJET:DESKEW:DESKEWMidlevel?
- DPOJET:DESKEW:DESKEWchannel {CH<x>}
- DPOJET:DESKEW:DESKEWchannel?
- DPOJET:DESKEW:EDGE {RISE|FALL|BOTH}
- DPOJET:DESKEW:EDGE?
- DPOJET:DESKEW:MAXimum <NR3>
- DPOJET:DESKEW:MAXimum?
- DPOJET:DESKEW:MINimum <NR3>
- DPOJET:DESKEW:MINimum?
- DPOJET:DESKEW:REFChannel {CH1 - CH4}
- DPOJET:DESKEW:REFChannel?
- DPOJET:DESKEW:REFHysteresis <NR3>
- DPOJET:DESKEW:REFHysteresis?
- DPOJET:DESKEW:REFMidlevel <NR3>
- DPOJET:DESKEW:REFMidlevel?
- DPOJET:DESKEW?
- DPOJET:DIRacmodel {FIBREchannel|PCIExpress}
- DPOJET:DIRacmodel?
- DPOJET:EXPORT {PLOT<x>, <file string>}
- DPOJET:EXPORTRaw {PLOT<x>, <file string>}
- DPOJET:GATING {OFF|ZOOM|CURSOR|MARKS}
- DPOJET:GATING?
- DPOJET:HALTFreerunonlimfail {1|0}
- DPOJET:HALTFreerunonlimfail?
- DPOJET:HIGHPerfrendering <NR1>
- DPOJET:HIGHPerfrendering?
- DPOJET:INTERp {LINear|SINX}
- DPOJET:INTERp?
- DPOJET:JITtermode?
- DPOJET:JITtermodel {BUJ|Legacy}
- DPOJET:JITtermodel?
- DPOJET:LASTError?
- DPOJET:LIMITRise {1|0}
- DPOJET:LIMITRise?
- DPOJET:LIMits:FILEName <string>
- DPOJET:LIMits:FILEName?
- DPOJET:LIMits:STATE {1|0}
- DPOJET:LIMits:STATE?
- DPOJET:LOCKRJ {1|0 }
- DPOJET:LOCKRJ?
- DPOJET:LOCKRJValue <NR3>
- DPOJET:LOCKRJValue?
- DPOJET:LOGging:MEASurements:FOLDer <string>
- DPOJET:LOGging:MEASurements:FOLDer?
- DPOJET:LOGging:MEASurements:STATE {1|0}
- DPOJET:LOGging:MEASurements:STATE?
- DPOJET:LOGging:SNAPshot {STATistics|MEASurements}
- DPOJET:LOGging:STATistics:FILEName <string>
- DPOJET:LOGging:STATistics:FILEName?
- DPOJET:LOGging:STATistics:STATE {1|0}
- DPOJET:LOGging:STATistics:STATE?
- DPOJET:LOGging:WORSTcase:FOLDer <string>
- DPOJET:LOGging:WORSTcase:FOLDer?
- DPOJET:LOGging:WORSTcase:STATE {1|0}
- DPOJET:LOGging:WORSTcase:STATE?
- DPOJET:MEAS<x>:BER:TARGETBER <NR3>
- DPOJET:MEAS<x>:BER:TARGETBER?
- DPOJET:MEAS<x>:BITCfgmethod {MEAN|MODE}
- DPOJET:MEAS<x>:BITCfgmethod?
- DPOJET:MEAS<x>:BITConfig:ABSRELstate {0|1}
- DPOJET:MEAS<x>:BITConfig:ABSRELstate?
- DPOJET:MEAS<x>:BITConfig:ENDPercent <NR3>
- DPOJET:MEAS<x>:BITConfig:ENDPercent?
- DPOJET:MEAS<x>:BITConfig:NUMBins <NR3>
- DPOJET:MEAS<x>:BITConfig:NUMBins?
- DPOJET:MEAS<x>:BITConfig:STARTPercent <NR3>
- DPOJET:MEAS<x>:BITConfig:STARTPercent?
- DPOJET:MEAS<x>:BITPcnt <NR3>
- DPOJET:MEAS<x>:BITPcnt?
- DPOJET:MEAS<x>:BITType {ALLBits|NONTRANsition|TRANsition}
- DPOJET:MEAS<x>:BITType?
- DPOJET:MEAS<x>:BUSState:CLOCKPolarity {RISING|FALLING}
- DPOJET:MEAS<x>:BUSState:CLOCKPolarity?
- DPOJET:MEAS<x>:BUSState:FROMPattern <string>
- DPOJET:MEAS<x>:BUSState:FROMPattern?
- DPOJET:MEAS<x>:BUSState:FROMSymbol <string>
- DPOJET:MEAS<x>:BUSState:FROMSymbol?
- DPOJET:MEAS<x>:BUSState:MEASUREFrom {CLOCKEdge|START|STOP}
- DPOJET:MEAS<x>:BUSState:MEASUREFrom?
- DPOJET:MEAS<x>:BUSState:MEASURETO {START|STOP|CLOCKEdge}
- DPOJET:MEAS<x>:BUSState:MEASURETO?
- DPOJET:MEAS<x>:BUSState:MEASUREType {SYMbol|PATTern}
- DPOJET:MEAS<x>:BUSState:MEASUREType?
- DPOJET:MEAS<x>:BUSState:TOPattern <string>
- DPOJET:MEAS<x>:BUSState:TOPattern?
- DPOJET:MEAS<x>:BUSState:TOSymbol <string>
- DPOJET:MEAS<x>:BUSState:TOSymbol?
- DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard <string>
- DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard?
- DPOJET:MEAS<x>:CLOCKRecovery:BWType {LOOPBW|JTFBW}
- DPOJET:MEAS<x>:CLOCKRecovery:BWType?
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate?
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency?
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath <string>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath?
- DPOJET:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:DAMPing?
- DPOJET:MEAS<x>:CLOCKRecovery:DATARate {1|0}
- DPOJET:MEAS<x>:CLOCKRecovery:DATARate?
- DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth?
- DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?
- DPOJET:MEAS<x>:CLOCKRecovery:METHod {STANDARD|CUSTOM|CONSTMEAN|CONSTFIXED|EXPEDGE|EXPPLL|CONSTMEDIAN|BEHAVIORAL}
- DPOJET:MEAS<x>:CLOCKRecovery:METHod?
- DPOJET:MEAS<x>:CLOCKRecovery:MODel {ONE|TWO}
- DPOJET:MEAS<x>:CLOCKRecovery:MODel?
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO?
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual?
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype {FIRST|EVERY}
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype?
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset?
- DPOJET:MEAS<x>:CLOCKRecovery:PATTern {1|0}
- DPOJET:MEAS<x>:CLOCKRecovery:PATTern?
- DPOJET:MEAS<x>:CLOCKRecovery:STAndard <string>
- DPOJET:MEAS<x>:CLOCKRecovery:STAndard?
- DPOJET:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF}
- DPOJET:MEAS<x>:COMMONMode:FILTers:STATE?
- DPOJET:MEAS<x>:CUSTOMGATING:FROMedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:CUSTOMGATING:FROMedge?
- DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge {FIRST|ALL}
- DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge?
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE {GATE1|GATE2|GATE3 GATE4|GATE5|GATE6|GATE7|GATE8|GATE9|GATE10|GATE11|GATE12|GATE13|GATE14|GATE15|GATE16|NONE}
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE?
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE {GATE1|GATE2|GATE3 GATE4|GATE5|GATE6|GATE7|GATE8|GATE9|GATE10|GATE11|GATE12|GATE13|GATE14|GATE15|GATE16|NONE }
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE?
- DPOJET:MEAS<x>:CUSTOMGATING:TOedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:CUSTOMGATING:TOedge?
- DPOJET:MEAS<x>:CUSTomname <string>
- DPOJET:MEAS<x>:CUSTomname?
- DPOJET:MEAS<x>:DATA?
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState {ON|OFF|1|0}
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState?
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue <NR3>
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue?
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState {ON|OFF|1|0}
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState?
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue <NR3>
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue?
- DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION {MANUAL,AUTO}
- DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION?
- DPOJET:MEAS<x>:DFE:MANUALDELAY <NR3>
- DPOJET:MEAS<x>:DFE:MANUALDELAY?
- DPOJET:MEAS<x>:DFE:MEASatpercent <NR3>
- DPOJET:MEAS<x>:DFE:MEASatpercent?
- DPOJET:MEAS<x>:DFE:RESOlution <NR3>
- DPOJET:MEAS<x>:DFE:RESOlution?
- DPOJET:MEAS<x>:DFE:TAPState {0|1}
- DPOJET:MEAS<x>:DFE:TAPState?
- DPOJET:MEAS<x>:DFE:TAPValue <NR3>
- DPOJET:MEAS<x>:DFE:TAPValue?
- DPOJET:MEAS<x>:DISPLAYNAME?
- DPOJET:MEAS<x>:EDGE1 {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:EDGE1?
- DPOJET:MEAS<x>:EDGE2 {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:EDGE2?
- DPOJET:MEAS<x>:EDGEIncre <NR3>
- DPOJET:MEAS<x>:EDGEIncre?
- DPOJET:MEAS<x>:EDGES:EYEHeightstate {1|0}
- DPOJET:MEAS<x>:EDGES:EYEHeightstate?
- DPOJET:MEAS<x>:EDGES:FROMLevel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:FROMLevel?
- DPOJET:MEAS<x>:EDGES:LEVel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:LEVel?
- DPOJET:MEAS<x>:EDGES:SLEWRATETechnique {NOMinalmethod|DDRmethod}
- DPOJET:MEAS<x>:EDGES:SLEWRATETechnique?
- DPOJET:MEAS<x>:EDGES:SUBRATEDivisor {TWO|FOUR|EIGHT}
- DPOJET:MEAS<x>:EDGES:SUBRATEDivisor?
- DPOJET:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:TOLevel?
- DPOJET:MEAS<x>:EDGES:USERDefinedvoltage <NR3>
- DPOJET:MEAS<x>:EDGES:USERDefinedvoltage?
- DPOJET:MEAS<x>:EDGES:VOLTAGEState {1|0}
- DPOJET:MEAS<x>:EDGES:VOLTAGEState?
- DPOJET:MEAS<x>:FILTers:BLANKingtime <NR3>
- DPOJET:MEAS<x>:FILTers:BLANKingtime?
- DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ?
- DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC?
- DPOJET:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- DPOJET:MEAS<x>:FILTers:LOWPass:FREQ?
- DPOJET:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- DPOJET:MEAS<x>:FILTers:LOWPass:SPEC?
- DPOJET:MEAS<x>:FILTers:RAMPtime <NR3>
- DPOJET:MEAS<x>:FILTers:RAMPtime?
- DPOJET:MEAS<x>:FILTers:SJBAndwidth <NR3>
- DPOJET:MEAS<x>:FILTers:SJBAndwidth?
- DPOJET:MEAS<x>:FILTers:SJFRequency <NR3>
- DPOJET:MEAS<x>:FILTers:SJFRequency?
- DPOJET:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:FROMedge?
- DPOJET:MEAS<x>:HIGHREFVoltage <NR3>
- DPOJET:MEAS<x>:HIGHREFVoltage?
- DPOJET:MEAS<x>:LOGging:MEASurements:FILEname?
- DPOJET:MEAS<x>:LOGging:MEASurements:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:MEASurements:SELect?
- DPOJET:MEAS<x>:LOGging:STATistics:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:STATistics:SELect?
- DPOJET:MEAS<x>:LOGging:WORSTcase:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:WORSTcase:SELect?
- DPOJET:MEAS<x>:LOWREFVoltage <NR3>
- DPOJET:MEAS<x>:LOWREFVoltage?
- DPOJET:MEAS<x>:MARGIN:HITCOUNTValue <NR3>
- DPOJET:MEAS<x>:MARGIN:HITCOUNTValue?
- DPOJET:MEAS<x>:MARGIN:HITRATIOState {1|0}
- DPOJET:MEAS<x>:MARGIN:HITRATIOState?
- DPOJET:MEAS<x>:MARGIN:HITRATIOValue <NR3>
- DPOJET:MEAS<x>:MARGIN:HITRATIOValue?
- DPOJET:MEAS<x>:MARGIN:RESOlution <NR3>
- DPOJET:MEAS<x>:MARGIN:RESOlution?
- DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit?
- DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual <NR3>
- DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual?
- DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype { AUTOFIT|MANUAL}
- DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype?
- DPOJET:MEAS<x>:MASKfile <string>
- DPOJET:MEAS<x>:MASKfile?
- DPOJET:MEAS<x>:MEASRange:MAX <NR3>
- DPOJET:MEAS<x>:MEASRange:MAX?
- DPOJET:MEAS<x>:MEASRange:MIN <NR3>
- DPOJET:MEAS<x>:MEASRange:MIN?
- DPOJET:MEAS<x>:MEASRange:STATE {1|0}
- DPOJET:MEAS<x>:MEASRange:STATE?
- DPOJET:MEAS<x>:MEASStart <NR3>
- DPOJET:MEAS<x>:MEASStart?
- DPOJET:MEAS<x>:N <NR3>
- DPOJET:MEAS<x>:N?
- DPOJET:MEAS<x>:NAME?
- DPOJET:MEAS<x>:OPTIcal:BANDWIDth <NR3>
- DPOJET:MEAS<x>:OPTIcal:BANDWIDth?
- DPOJET:MEAS<x>:OPTIcal:BTFILTEr <string>
- DPOJET:MEAS<x>:OPTIcal:BTFILTEr?
- DPOJET:MEAS<x>:OPTIcal:FFETAPS <string>
- DPOJET:MEAS<x>:OPTIcal:FFETAPS?
- DPOJET:MEAS<x>:OPTIcal:SCOPERN <NR3>
- DPOJET:MEAS<x>:OPTIcal:SCOPERN?
- DPOJET:MEAS<x>:OPTIcal:TARGETBer <NR3>
- DPOJET:MEAS<x>:OPTIcal:TARGETBer?
- DPOJET:MEAS<x>:OPTIcal:WFMTYpe {CONTINUOUS|MODULATED}
- DPOJET:MEAS<x>:OPTIcal:WFMTYpe?
- DPOJET:MEAS<x>:PHASENoise:HIGHLimit <NR3>
- DPOJET:MEAS<x>:PHASENoise:HIGHLimit?
- DPOJET:MEAS<x>:PHASENoise:LOWLimit <NR3>
- DPOJET:MEAS<x>:PHASENoise:LOWLimit?
- DPOJET:MEAS<x>:PLOTFILES?
- DPOJET:MEAS<x>:REFVoltage {100|—100}
- DPOJET:MEAS<x>:REFVoltage?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus?
- DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev?
- DPOJET:MEAS<x>:RESULts:ALLAcqs?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAX?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MIN?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC?
- DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK?
- DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation?
- DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus?
- DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev?
- DPOJET:MEAS<x>:RESULts:GETAll?
- DPOJET:MEAS<x>:RESULts:STATus?
- DPOJET:MEAS<x>:RESULts:VIew?
- DPOJET:MEAS<x>:RESULts?
- DPOJET:MEAS<x>:RJDJ:BER <NR3>
- DPOJET:MEAS<x>:RJDJ:BER?
- DPOJET:MEAS<x>:RJDJ:DETECTPLEN {ON|OFF|1|0}
- DPOJET:MEAS<x>:RJDJ:DETECTPLEN?
- DPOJET:MEAS<x>:RJDJ:NCMODe {1|0}
- DPOJET:MEAS<x>:RJDJ:NCMODe?
- DPOJET:MEAS<x>:RJDJ:PATLen <NR3>
- DPOJET:MEAS<x>:RJDJ:PATLen?
- DPOJET:MEAS<x>:RJDJ:SCOPERN <NR3>
- DPOJET:MEAS<x>:RJDJ:SCOPERN?
- DPOJET:MEAS<x>:RJDJ:SNCREFID <string>
- DPOJET:MEAS<x>:RJDJ:SNCREFID?
- DPOJET:MEAS<x>:RJDJ:TYPe {ARBITrary|REPEating}
- DPOJET:MEAS<x>:RJDJ:TYPe?
- DPOJET:MEAS<x>:RJDJ:WINDOwlength <NR3>
- DPOJET:MEAS<x>:RJDJ:WINDOwlength?
- DPOJET:MEAS<x>:RNDN:AUTODETECTpattern {ON|OFF|1|0}
- DPOJET:MEAS<x>:RNDN:AUTODETECTpattern?
- DPOJET:MEAS<x>:RNDN:BER <NR3>
- DPOJET:MEAS<x>:RNDN:BER?
- DPOJET:MEAS<x>:RNDN:NCMODe {1|0}
- DPOJET:MEAS<x>:RNDN:NCMODe?
- DPOJET:MEAS<x>:RNDN:PATLen <NR3>
- DPOJET:MEAS<x>:RNDN:PATLen?
- DPOJET:MEAS<x>:RNDN:SCOPERN <NR3>
- DPOJET:MEAS<x>:RNDN:SCOPERN?
- DPOJET:MEAS<x>:RNDN:SNCREFID <string>
- DPOJET:MEAS<x>:RNDN:SNCREFID?
- DPOJET:MEAS<x>:RNDN:TYPe {ARBITrary|REPEating}
- DPOJET:MEAS<x>:RNDN:TYPe?
- DPOJET:MEAS<x>:RNDN:WINDOwlength <NR3>
- DPOJET:MEAS<x>:RNDN:WINDOwlength?
- DPOJET:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- DPOJET:MEAS<x>:SIGNALType?
- DPOJET:MEAS<x>:SOUrce1 {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|D0 — D15}
- DPOJET:MEAS<x>:SOUrce1?
- DPOJET:MEAS<x>:SOUrce2 {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|D0 — D15}
- DPOJET:MEAS<x>:SOUrce2?
- DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO?
- DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual <NR3>
- DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual?
- DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANUAL}
- DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?
- DPOJET:MEAS<x>:TIMEDATa?
- DPOJET:MEAS<x>:TOEdge {SAMEas|OPPositeas}
- DPOJET:MEAS<x>:TOEdge?
- DPOJET:MEAS<x>:ZOOMEVENT {MAX|MIN}
- DPOJET:MINBUJUI <NR3>
- DPOJET:MINBUJUI?
- DPOJET:NOISEENABLED {ON|OFF|1|0}
- DPOJET:NUMMeas?
- DPOJET:NUMPlot?
- DPOJET:OPTICALUNITType {WATT|DBM}
- DPOJET:OPTICALUNITType?
- DPOJET:PLOT<x>:BATHtub:BER <NR3>
- DPOJET:PLOT<x>:BATHtub:BER?
- DPOJET:PLOT<x>:BATHtub:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:BATHtub:VERTical:SCALE?
- DPOJET:PLOT<x>:BATHtub:XAXISUnits { UNITIntervals|SECOnds }
- DPOJET:PLOT<x>:BATHtub:XAXISUnits?
- DPOJET:PLOT<x>:BERContour:ALIGNment {AUTO|LEFT|CENter}
- DPOJET:PLOT<x>:BERContour:ALIGNment?
- DPOJET:PLOT<x>:BERContour:BER1E12V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E12V?
- DPOJET:PLOT<x>:BERContour:BER1E15V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E15V?
- DPOJET:PLOT<x>:BERContour:BER1E18V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E18V?
- DPOJET:PLOT<x>:BERContour:BER1E6V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E6V?
- DPOJET:PLOT<x>:BERContour:BER1E9V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E9V?
- DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale?
- DPOJET:PLOT<x>:BERContour:HORizontal:RESolution <NR3>
- DPOJET:PLOT<x>:BERContour:HORizontal:RESolution?
- DPOJET:PLOT<x>:BERContour:MASK {1|0}
- DPOJET:PLOT<x>:BERContour:MASK?
- DPOJET:PLOT<x>:BERContour:MASKFile <string>
- DPOJET:PLOT<x>:BERContour:MASKFile?
- DPOJET:PLOT<x>:BERContour:SUPERImpose {1|0}
- DPOJET:PLOT<x>:BERContour:SUPERImpose?
- DPOJET:PLOT<x>:BERContour:TARGETBER {1|0}
- DPOJET:PLOT<x>:BERContour:TARGETBER?
- DPOJET:PLOT<x>:BEREye:BER1E12V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E12V?
- DPOJET:PLOT<x>:BEREye:BER1E15V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E15V?
- DPOJET:PLOT<x>:BEREye:BER1E18V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E18V?
- DPOJET:PLOT<x>:BEREye:BER1E6V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E6V?
- DPOJET:PLOT<x>:BEREye:BER1E9V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E9V?
- DPOJET:PLOT<x>:BEREye:TARGETBER {1|0}
- DPOJET:PLOT<x>:BEREye:TARGETBER?
- DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD?
- DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins?
- DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ?
- DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ?
- DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ?
- DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE?
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE?
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO?
- DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE?
- DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins { TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins?
- DPOJET:PLOT<x>:COMPOSITENoisehist:PN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:PN?
- DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN?
- DPOJET:PLOT<x>:COMPOSITENoisehist:TN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:TN?
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V?
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V?
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V?
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V?
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V?
- DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT <NR2>
- DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT?
- DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH <NR2>
- DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH?
- DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER?
- DPOJET:PLOT<x>:CURRENTUISACquired?
- DPOJET:PLOT<x>:CURRENTUISANalyzed?
- DPOJET:PLOT<x>:DATA:XDATa:DDJDCD?
- DPOJET:PLOT<x>:DATA:XDATa:DDNONE?
- DPOJET:PLOT<x>:DATA:XDATa:DDNZERO?
- DPOJET:PLOT<x>:DATA:XDATa:PJ?
- DPOJET:PLOT<x>:DATA:XDATa:PN?
- DPOJET:PLOT<x>:DATA:XDATa:RJBUJ?
- DPOJET:PLOT<x>:DATA:XDATa:RNNPN?
- DPOJET:PLOT<x>:DATA:XDATa:TJ?
- DPOJET:PLOT<x>:DATA:XDATa:TN?
- DPOJET:PLOT<x>:DATA:XDATa?
- DPOJET:PLOT<x>:DATA:YDATa:DDJDCD?
- DPOJET:PLOT<x>:DATA:YDATa:DDNONE?
- DPOJET:PLOT<x>:DATA:YDATa:DDNZERO?
- DPOJET:PLOT<x>:DATA:YDATa:PJ?
- DPOJET:PLOT<x>:DATA:YDATa:PN?
- DPOJET:PLOT<x>:DATA:YDATa:RJBUJ?
- DPOJET:PLOT<x>:DATA:YDATa:RNNPN?
- DPOJET:PLOT<x>:DATA:YDATa:TJ?
- DPOJET:PLOT<x>:DATA:YDATa:TN?
- DPOJET:PLOT<x>:DATA:YDATa?
- DPOJET:PLOT<x>:EXPORTRaw?
- DPOJET:PLOT<x>:EYE:ALIGNment {AUTO|LEFT|CENter}
- DPOJET:PLOT<x>:EYE:ALIGNment?
- DPOJET:PLOT<x>:EYE:EYEVerticalscale {SCALETOData, SCALETORefclk}
- DPOJET:PLOT<x>:EYE:EYEVerticalscale?
- DPOJET:PLOT<x>:EYE:HORIZScale {1|0}
- DPOJET:PLOT<x>:EYE:HORIZScale?
- DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale?
- DPOJET:PLOT<x>:EYE:HORizontal:RESolution <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:RESolution?
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx?
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn?
- DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor {AUTO, TWELVEPOINTEIGHT, SIXTEEN}
- DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor?
- DPOJET:PLOT<x>:EYE:INTERPolationtype { INTERPOLATION|NONINTERPOLATION }
- DPOJET:PLOT<x>:EYE:INTERPolationtype?
- DPOJET:PLOT<x>:EYE:MASKfile <string>
- DPOJET:PLOT<x>:EYE:MASKfile?
- DPOJET:PLOT<x>:EYE:STATE {1|0}
- DPOJET:PLOT<x>:EYE:STATE?
- DPOJET:PLOT<x>:EYE:SUPERImpose {1|0}
- DPOJET:PLOT<x>:EYE:SUPERImpose?
- DPOJET:PLOT<x>:EYE:VERTICALAlignment {1|0}
- DPOJET:PLOT<x>:EYE:VERTICALAlignment?
- DPOJET:PLOT<x>:EYE:VERTScale {1|0}
- DPOJET:PLOT<x>:EYE:VERTScale?
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx <NR3>
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx?
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn <NR3>
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn?
- DPOJET:PLOT<x>:HISTOgram:AUTOset {EXECute}
- DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale?
- DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter <NR3>
- DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter?
- DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN <NR3>
- DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN?
- DPOJET:PLOT<x>:HISTOgram:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:HISTOgram:NUMBins?
- DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE?
- DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits { UNITAmplitudes|VOLTs }
- DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits?
- DPOJET:PLOT<x>:PDFEye:BER1E12V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E12V?
- DPOJET:PLOT<x>:PDFEye:BER1E15V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E15V?
- DPOJET:PLOT<x>:PDFEye:BER1E18V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E18V?
- DPOJET:PLOT<x>:PDFEye:BER1E6V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E6V?
- DPOJET:PLOT<x>:PDFEye:BER1E9V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E9V?
- DPOJET:PLOT<x>:PDFEye:TARGETBER {1|0}
- DPOJET:PLOT<x>:PDFEye:TARGETBER?
- DPOJET:PLOT<x>:PHASEnoise:BASEline <NR3>
- DPOJET:PLOT<x>:PHASEnoise:BASEline?
- DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter {ONEBYHUNDREDTHdecade|ONEBYTENTHDECADE|ONEDECADE}
- DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter?
- DPOJET:PLOT<x>:SOUrce?
- DPOJET:PLOT<x>:SPECtrum:BASE <NR3>
- DPOJET:PLOT<x>:SPECtrum:BASE?
- DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE?
- DPOJET:PLOT<x>:SPECtrum:MODE {NORMal|AVErage|PEAKhold}
- DPOJET:PLOT<x>:SPECtrum:MODE?
- DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE?
- DPOJET:PLOT<x>:TOTALUISAcquired?
- DPOJET:PLOT<x>:TOTALUISAnalyzed?
- DPOJET:PLOT<x>:TRANSfer:DENominator {MEAS1 - MEAS99}
- DPOJET:PLOT<x>:TRANSfer:DENominator?
- DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE?
- DPOJET:PLOT<x>:TRANSfer:MODE {NORMal|AVErage}
- DPOJET:PLOT<x>:TRANSfer:MODE?
- DPOJET:PLOT<x>:TRANSfer:NUMerator {MEAS1 - MEAS99}
- DPOJET:PLOT<x>:TRANSfer:NUMerator?
- DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE?
- DPOJET:PLOT<x>:TREND:TYPe {VECTOR|BAR}
- DPOJET:PLOT<x>:TREND:TYPe?
- DPOJET:PLOT<x>:TYPe?
- DPOJET:PLOT<x>:VERTBATHtub:BER <NR3>
- DPOJET:PLOT<x>:VERTBATHtub:BER?
- DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE?
- DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits {VOLTs|UNITAMPLITUDES}
- DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits?
- DPOJET:PLOT<x>:XUnits?
- DPOJET:PLOT<x>:YUnits?
- DPOJET:POPULATION:CONDition {EACHmeas|LASTmeas}
- DPOJET:POPULATION:CONDition?
- DPOJET:POPULATION:LIMIT <NR3>
- DPOJET:POPULATION:LIMIT?
- DPOJET:POPULATION:LIMITBY {ACQuisitions|POPUlation}
- DPOJET:POPULATION:LIMITBY?
- DPOJET:POPULATION:STATE {1|0}
- DPOJET:POPULATION:STATE?
- DPOJET:QUALify:ACTIVE {HIGH|LOW}
- DPOJET:QUALify:ACTIVE?
- DPOJET:QUALify:SOUrce {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|SEARCH0 - SEARCH8}
- DPOJET:QUALify:SOUrce?
- DPOJET:QUALify:STATE {1|0}
- DPOJET:QUALify:STATE?
- DPOJET:REFLevel:CH<x>:MIDZero {1|0}
- DPOJET:REFLevel:CH<x>:MIDZero?
- DPOJET:REFLevels:AUTOset {EXECute}
- DPOJET:REFLevels:AUTOset:STATE?
- DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh?
- DPOJET:REFLevels:CH<x>:ABSolute:FALLLow <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLLow?
- DPOJET:REFLevels:CH<x>:ABSolute:FALLMid <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLMid?
- DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis?
- DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh?
- DPOJET:REFLevels:CH<x>:ABSolute:RISELow <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISELow?
- DPOJET:REFLevels:CH<x>:ABSolute:RISEMid <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISEMid?
- DPOJET:REFLevels:CH<x>:ABSolute?
- DPOJET:REFLevels:CH<x>:AUTOSet {1|0}
- DPOJET:REFLevels:CH<x>:BASETop {MINMax|FULLhistogram|EYEhistogram|AUTO}
- DPOJET:REFLevels:CH<x>:BASETop?
- DPOJET:REFLevels:CH<x>:PERcent:FALLHigh <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLHigh?
- DPOJET:REFLevels:CH<x>:PERcent:FALLLow <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLLow?
- DPOJET:REFLevels:CH<x>:PERcent:FALLMid <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLMid?
- DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis?
- DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel { 1|0 }
- DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel?
- DPOJET:REFLevels:CH<x>:PERcent:RISEHigh <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISEHigh?
- DPOJET:REFLevels:CH<x>:PERcent:RISELow <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISELow?
- DPOJET:REFLevels:CH<x>:PERcent:RISEMid <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISEMid?
- DPOJET:REFLevels:CH<x>:PERcent?
- DPOJET:REPORT {EXECute|APPEnd}
- DPOJET:REPORT:APPlicationconfig {1|0}
- DPOJET:REPORT:APPlicationconfig?
- DPOJET:REPORT:AUTOincrement {1|0}
- DPOJET:REPORT:AUTOincrement?
- DPOJET:REPORT:COMments <string>
- DPOJET:REPORT:COMments?
- DPOJET:REPORT:DETailedresults {1|0}
- DPOJET:REPORT:DETailedresults?
- DPOJET:REPORT:ENABlecomments {1|0}
- DPOJET:REPORT:ENABlecomments?
- DPOJET:REPORT:GETIMAGE?
- DPOJET:REPORT:GETIMAGEName?
- DPOJET:REPORT:GETXMLReport?
- DPOJET:REPORT:PASSFailresults {1|0}
- DPOJET:REPORT:PASSFailresults?
- DPOJET:REPORT:PLOTimages {1|0}
- DPOJET:REPORT:PLOTimages?
- DPOJET:REPORT:REPORTName <string>
- DPOJET:REPORT:REPORTName?
- DPOJET:REPORT:SAVEWaveforms {1|0}
- DPOJET:REPORT:SAVEWaveforms?
- DPOJET:REPORT:SETIMAGEPath <file string>
- DPOJET:REPORT:SETupconfig {1|0}
- DPOJET:REPORT:SETupconfig?
- DPOJET:REPORT:STATE?
- DPOJET:REPORT:TYPe {MHT|PDF}
- DPOJET:REPORT:TYPe?
- DPOJET:REPORT:VIEWreport {1|0}
- DPOJET:REPORT:VIEWreport?
- DPOJET:RESULts:GETALLResults?
- DPOJET:RESULts:STATus?
- DPOJET:RESULts:VIew {SUMmary|DETails}
- DPOJET:RESULts:VIew?
- DPOJET:SAVE {MEAS<x>|REF<x>}
- DPOJET:SAVEALLPLOTS
- DPOJET:SETIMAGETPath <file string>
- DPOJET:SETIMAGETPath?
- DPOJET:SETLOGGINGPath <file string>
- DPOJET:SETLOGGINGPath?
- DPOJET:SETREPORTPath <file string>
- DPOJET:SETREPORTPath?
- DPOJET:SHOWMEASWARNing {1|0}
- DPOJET:SHOWMEASWARNing?
- DPOJET:SNC:ACTIvate
- DPOJET:SNC:CLOse
- DPOJET:SOURCEAutoset {HORizontal|VERTical|BOTH}
- DPOJET:SOURCEAutoset:HORizontal:UICount <NR3>
- DPOJET:SOURCEAutoset:HORizontal:UICount?
- DPOJET:SOURCEAutoset:HORizontal:UIValue <NR3>
- DPOJET:SOURCEAutoset:HORizontal:UIValue?
- DPOJET:SOURCEAutoset:STATE?
- DPOJET:STATE {RUN|SINGLE|RECALC|CLEAR|STOP}
- DPOJET:STATE?
- DPOJET:TDCOMPensation {ON|OFF|1|0}
- DPOJET:TDCOMPensation?
- DPOJET:UNITType {UNITinterval|SEConds}
- DPOJET:UNITType?
- DPOJET:VERTUNITType {UNITamplitude|VOLts}
- DPOJET:VERTUNITType?
- DPOJET:VERsion?

Dpojet

Bases: SCPICmdRead

The DPOJET command tree.

Usage
  • Using the .query() method will send the DPOJET? query.
  • Using the .verify(value) method will send the DPOJET? query and raise an AssertionError if the returned value does not match value.
Properties
  • .activate: The DPOJET:ACTIVATE command.
  • .addmeas: The DPOJET:ADDMeas command.
  • .addplot: The DPOJET:ADDPlot command.
  • .analysismethod: The DPOJET:ANALYSISMETHOD command.
  • .applyall: The DPOJET:APPLYAll command.
  • .bitratestate: The DPOJET:BITRatestate command.
  • .clearallmeas: The DPOJET:CLEARALLMeas command.
  • .clearallplots: The DPOJET:CLEARALLPlots command.
  • .dataratelimits: The DPOJET:DATAratelimits command.
  • .deskew: The DPOJET:DESKEW command.
  • .diracmodel: The DPOJET:DIRacmodel command.
  • .export: The DPOJET:EXPORT command.
  • .exportraw: The DPOJET:EXPORTRaw command.
  • .gating: The DPOJET:GATING command.
  • .haltfreerunonlimfail: The DPOJET:HALTFreerunonlimfail command.
  • .highperfrendering: The DPOJET:HIGHPerfrendering command.
  • .interp: The DPOJET:INTERp command.
  • .jittermode: The DPOJET:JITtermode command.
  • .jittermodel: The DPOJET:JITtermodel command.
  • .lasterror: The DPOJET:LASTError command.
  • .limitrise: The DPOJET:LIMITRise command.
  • .limits: The DPOJET:LIMits command tree.
  • .lockrj: The DPOJET:LOCKRJ command.
  • .lockrjvalue: The DPOJET:LOCKRJValue command.
  • .logging: The DPOJET:LOGging command tree.
  • .meas: The DPOJET:MEAS<x> command tree.
  • .minbujui: The DPOJET:MINBUJUI command.
  • .noiseenabled: The DPOJET:NOISEENABLED command.
  • .nummeas: The DPOJET:NUMMeas command.
  • .numplot: The DPOJET:NUMPlot command.
  • .opticalunittype: The DPOJET:OPTICALUNITType command.
  • .plot: The DPOJET:PLOT<x> command tree.
  • .population: The DPOJET:POPULATION command tree.
  • .qualify: The DPOJET:QUALify command tree.
  • .reflevel: The DPOJET:REFLevel command tree.
  • .reflevels: The DPOJET:REFLevels command tree.
  • .report: The DPOJET:REPORT command.
  • .results: The DPOJET:RESULts command tree.
  • .save: The DPOJET:SAVE command.
  • .saveallplots: The DPOJET:SAVEALLPLOTS command.
  • .setimagetpath: The DPOJET:SETIMAGETPath command.
  • .setloggingpath: The DPOJET:SETLOGGINGPath command.
  • .setreportpath: The DPOJET:SETREPORTPath command.
  • .showmeaswarning: The DPOJET:SHOWMEASWARNing command.
  • .snc: The DPOJET:SNC command tree.
  • .sourceautoset: The DPOJET:SOURCEAutoset command.
  • .state: The DPOJET:STATE command.
  • .tdcompensation: The DPOJET:TDCOMPensation command.
  • .unittype: The DPOJET:UNITType command.
  • .vertunittype: The DPOJET:VERTUNITType command.
  • .version: The DPOJET:VERsion command.

activate property 

activate: DpojetActivate

Return the DPOJET:ACTIVATE command.

Description
  • This command launches the DPOJET to active state.
Usage
  • Using the .write() method will send the DPOJET:ACTIVATE command.
SCPI Syntax 
- DPOJET:ACTIVATE

addmeas property 

addmeas: DpojetAddmeas

Return the DPOJET:ADDMeas command.

Description
  • This set-only command adds the specified measurement to the bottom of the current DPOJET list of measurements and will appear in the results summary page.
Usage
  • Using the .write(value) method will send the DPOJET:ADDMeas value command.
SCPI Syntax 
- DPOJET:ADDMeas {PERIod|CCPeriod|FREQuency|NPERiod|PWIdth|NWIdth|PDUTy|NDUTy|PCCDuty|NCCDuty|DATARATE|TIE|RJ|RJDirac|TJber|DJ|DJDirac|PHASENoise|DCD|DDJ|PJ|J2|J9|SRJ|PJrms|SJFREQ|PKPKCLKTJ|PKPKCLKRJ|PKPKCLKDJ|PJRMS|FN|RJH|RJV|PJH|PJV|RN|RNV|RNH|DN|DDN|DDN_1|DDN_0|PN|PNV|PNH|NPN|TNBER|NOISESUMMARY|UNITAMPLITUDE|RISEtime|SETup|HIGHTime|FALLtime|HOLD|LOWTime|SKEW|GATEDSKEW|HEIght|WIDth|MASKHits|WIDTHBer|HEIGHTBer|CYCLEMIN|CYCLEMAX|ACRMS|ACCOMmonmode|COMmonmode|HIGH|TNTratio|HIGHLOW|LOW|VDIFFxovr|RISESLEWrate|FALLSLEWrate|OVERShoot|UNDERShoot|CYCLEPktopk|JITTERSummary|PCIETTXDiffpp|PCIEDEemph|PCIETTx|PCIETTXRise|PCIETTXFall|PCIEUI|PCIETMinpulse|PCIEMEdmxjitter|PCIETRfmismch|PCIESSCFReqdev|PCIEMAXMINratio|PCIESSCPROFile|PCIEVEye|PCIETTXUTJ|PCIETTXUDJDD|PCIETTXUPWTJ|PCIETTXUPWDJDD|PCIETTXDDJ|PCIEVTXBOOST|PCIEVTXNOEQ|PCIEVTXEIEOS|PCIEPS21TX|PCIEACCommonmode|VTXDiffpp|TMINPULSETJ|TCDRslewmax|USBUI|USBACCommonmode|TMINPULSEDJ|QFACTOR|EYELOW|EYEHIGH|TCMDTOCMD|TIMEOUTSIDELEVEL|SSCFREQDEVMAX|SSCFREQDEVMIN|SSCFREQDEV|SSCMODrate|SSCPROfile|USBSSCFREQDEVMAX|USBSSCFREQDEVMIN|USBSSCMODrate|USBSSCPROFile|AUTOFITMaskhits|AOP|EXRATIO|OMA|OPTHIGH|OPTLOW|EYECROSSLEVEL|EYECROSSTIME|EYECROSSPERCENT|DFEEW|DFEEH|DFEEYEDIAGRAM|VWOE|MASKMARGIN|MASKHITRATIO|RIN|RINXOMA|TDEC }

addplot property 

addplot: DpojetAddplot

Return the DPOJET:ADDPlot command.

Description
  • This set-only command creates a plot of the specified type on the specified DPOJET measurement. Up to four plots can be created.
Usage
  • Using the .write(value) method will send the DPOJET:ADDPlot value command.
SCPI Syntax 
- DPOJET:ADDPlot {TIMEtrend|DATAarray|HISTOgram|SPECtrum|TRANSfer|PHASEnoise|EYE|WAVEform|BATHtub|QBathtub|QPulsewidth|COMPOSITEJitterhist|NOISEBAthtub|BERContour|CORRELATEDEye|PDFEye|BEREye|COMPOSITENoisehist}, MEAS<x>

analysismethod property 

analysismethod: DpojetAnalysismethod

Return the DPOJET:ANALYSISMETHOD command.

Description
  • This command sets or queries the current analysis method value.
Usage
  • Using the .query() method will send the DPOJET:ANALYSISMETHOD? query.
  • Using the .verify(value) method will send the DPOJET:ANALYSISMETHOD? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:ANALYSISMETHOD value command.
SCPI Syntax 
- DPOJET:ANALYSISMETHOD { JITTEROnly|JITTERNoise }
- DPOJET:ANALYSISMETHOD?

applyall property 

applyall: DpojetApplyall

Return the DPOJET:APPLYAll command.

Description
  • This command applies configuration of specified type of the specified DPOJET measurement to all other DPOJET measurements.
Usage
  • Using the .write(value) method will send the DPOJET:APPLYAll value command.
SCPI Syntax 
- DPOJET:APPLYAll {FILTers|CLOCKRecovery|RJDJ}, MEAS<x>

bitratestate property 

bitratestate: DpojetBitratestate

Return the DPOJET:BITRatestate command.

Description
  • This command sets or queries the user bitrate state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:BITRatestate? query.
  • Using the .verify(value) method will send the DPOJET:BITRatestate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:BITRatestate value command.
SCPI Syntax 
- DPOJET:BITRatestate {0|1}
- DPOJET:BITRatestate?

clearallmeas property 

clearallmeas: DpojetClearallmeas

Return the DPOJET:CLEARALLMeas command.

Description
  • This set-only command clears the entire current list of defined measurements in DPOJET.
Usage
  • Using the .write() method will send the DPOJET:CLEARALLMeas command.
SCPI Syntax 
- DPOJET:CLEARALLMeas

clearallplots property 

clearallplots: DpojetClearallplots

Return the DPOJET:CLEARALLPlots command.

Description
  • This set-only command clears the entire current list of defined plots in DPOJET.
Usage
  • Using the .write() method will send the DPOJET:CLEARALLPlots command.
SCPI Syntax 
- DPOJET:CLEARALLPlots

dataratelimits property 

dataratelimits: DpojetDataratelimits

Return the DPOJET:DATAratelimits command.

Description
  • This command sets or queries the reference bitrate for measurement limits.
Usage
  • Using the .query() method will send the DPOJET:DATAratelimits? query.
  • Using the .verify(value) method will send the DPOJET:DATAratelimits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DATAratelimits value command.
SCPI Syntax 
- DPOJET:DATAratelimits <NR3>
- DPOJET:DATAratelimits?

deskew property 

deskew: DpojetDeskew

Return the DPOJET:DESKEW command.

Description
  • This command performs a DPOJET deskew operation with the settings specified in DPOJET:DESKEW.
Usage
  • Using the .query() method will send the DPOJET:DESKEW? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW value command.
SCPI Syntax 
- DPOJET:DESKEW {EXEcute}
- DPOJET:DESKEW?
Sub-properties
  • .deskewhysteresis: The DPOJET:DESKEW:DESKEWHysteresis command.
  • .deskewmidlevel: The DPOJET:DESKEW:DESKEWMidlevel command.
  • .deskewchannel: The DPOJET:DESKEW:DESKEWchannel command.
  • .edge: The DPOJET:DESKEW:EDGE command.
  • .maximum: The DPOJET:DESKEW:MAXimum command.
  • .minimum: The DPOJET:DESKEW:MINimum command.
  • .refchannel: The DPOJET:DESKEW:REFChannel command.
  • .refhysteresis: The DPOJET:DESKEW:REFHysteresis command.
  • .refmidlevel: The DPOJET:DESKEW:REFMidlevel command.

diracmodel property 

diracmodel: DpojetDiracmodel

Return the DPOJET:DIRacmodel command.

Description
  • This command sets or queries the current dirac model.
Usage
  • Using the .query() method will send the DPOJET:DIRacmodel? query.
  • Using the .verify(value) method will send the DPOJET:DIRacmodel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DIRacmodel value command.
SCPI Syntax 
- DPOJET:DIRacmodel {FIBREchannel|PCIExpress}
- DPOJET:DIRacmodel?

export property 

export: DpojetExport

Return the DPOJET:EXPORT command.

Description
  • This set-only command saves the specified DPOJET plot to the specified file path. The Format is determined through the filename extension, with a default of png if no extension is specified. Supported extensions include jpeg, jpg, tif, tiff, bmp, emf,.mat,.csv and png.
Usage
  • Using the .write(value) method will send the DPOJET:EXPORT value command.
SCPI Syntax 
- DPOJET:EXPORT {PLOT<x>, <file string>}

exportraw property 

exportraw: DpojetExportraw

Return the DPOJET:EXPORTRaw command.

Description
  • This set-only command saves the raw Eye diagram 2d histogram data to the specified file path. The format is determined through the filename extension. Supported extension include.csv Note: Ensure that the Plot window is open while sending this PI command; else a file will be not generated.
Usage
  • Using the .write(value) method will send the DPOJET:EXPORTRaw value command.
SCPI Syntax 
- DPOJET:EXPORTRaw {PLOT<x>, <file string>}

gating property 

gating: DpojetGating

Return the DPOJET:GATING command.

Description
  • This command sets or queries the gating state.
Usage
  • Using the .query() method will send the DPOJET:GATING? query.
  • Using the .verify(value) method will send the DPOJET:GATING? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:GATING value command.
SCPI Syntax 
- DPOJET:GATING {OFF|ZOOM|CURSOR|MARKS}
- DPOJET:GATING?

haltfreerunonlimfail property 

haltfreerunonlimfail: DpojetHaltfreerunonlimfail

Return the DPOJET:HALTFreerunonlimfail command.

Description
  • This command sets or queries the halt free-run on limit failure (On or Off).
Usage
  • Using the .query() method will send the DPOJET:HALTFreerunonlimfail? query.
  • Using the .verify(value) method will send the DPOJET:HALTFreerunonlimfail? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:HALTFreerunonlimfail value command.
SCPI Syntax 
- DPOJET:HALTFreerunonlimfail {1|0}
- DPOJET:HALTFreerunonlimfail?

highperfrendering property 

highperfrendering: DpojetHighperfrendering

Return the DPOJET:HIGHPerfrendering command.

Description
  • This command sets or queries the current high-performance eye rendering setting.
Usage
  • Using the .query() method will send the DPOJET:HIGHPerfrendering? query.
  • Using the .verify(value) method will send the DPOJET:HIGHPerfrendering? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:HIGHPerfrendering value command.
SCPI Syntax 
- DPOJET:HIGHPerfrendering <NR1>
- DPOJET:HIGHPerfrendering?

interp property 

interp: DpojetInterp

Return the DPOJET:INTERp command.

Description
  • This command sets or queries the current interpolation model.
Usage
  • Using the .query() method will send the DPOJET:INTERp? query.
  • Using the .verify(value) method will send the DPOJET:INTERp? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:INTERp value command.
SCPI Syntax 
- DPOJET:INTERp {LINear|SINX}
- DPOJET:INTERp?

jittermode property 

jittermode: DpojetJittermode

Return the DPOJET:JITtermode command.

Description
  • This command queries the current jitter mode.
Usage
  • Using the .query() method will send the DPOJET:JITtermode? query.
  • Using the .verify(value) method will send the DPOJET:JITtermode? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:JITtermode?

jittermodel property 

jittermodel: DpojetJittermodel

Return the DPOJET:JITtermodel command.

Description
  • This command sets the current jitter model.
Usage
  • Using the .query() method will send the DPOJET:JITtermodel? query.
  • Using the .verify(value) method will send the DPOJET:JITtermodel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:JITtermodel value command.
SCPI Syntax 
- DPOJET:JITtermodel {BUJ|Legacy}
- DPOJET:JITtermodel?

lasterror property 

lasterror: DpojetLasterror

Return the DPOJET:LASTError command.

Description
  • This query-only command returns the contents of the last pop-up warning dialog box. If no errors have occurred since startup, or since the last call to DPOJET:LASTError?, this command returns an empty string.
Usage
  • Using the .query() method will send the DPOJET:LASTError? query.
  • Using the .verify(value) method will send the DPOJET:LASTError? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:LASTError?

limitrise property 

limitrise: DpojetLimitrise

Return the DPOJET:LIMITRise command.

Description
  • This command turns on or off the ability to limit Rise/Fall measurements to transition bits only.
Usage
  • Using the .query() method will send the DPOJET:LIMITRise? query.
  • Using the .verify(value) method will send the DPOJET:LIMITRise? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LIMITRise value command.
SCPI Syntax 
- DPOJET:LIMITRise {1|0}
- DPOJET:LIMITRise?

limits property 

limits: DpojetLimits

Return the DPOJET:LIMits command tree.

Usage
  • Using the .query() method will send the DPOJET:LIMits? query.
  • Using the .verify(value) method will send the DPOJET:LIMits? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .filename: The DPOJET:LIMits:FILEName command.
  • .state: The DPOJET:LIMits:STATE command.

lockrj property 

lockrj: DpojetLockrj

Return the DPOJET:LOCKRJ command.

Description
  • This command sets or queries the Lock RJ Value.
Usage
  • Using the .query() method will send the DPOJET:LOCKRJ? query.
  • Using the .verify(value) method will send the DPOJET:LOCKRJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOCKRJ value command.
SCPI Syntax 
- DPOJET:LOCKRJ {1|0 }
- DPOJET:LOCKRJ?

lockrjvalue property 

lockrjvalue: DpojetLockrjvalue

Return the DPOJET:LOCKRJValue command.

Description
  • This command sets or queries the LockRJValue. Inorder to set LockRJValue to be effective, LOCKRJ to be 1 (enabled).
Usage
  • Using the .query() method will send the DPOJET:LOCKRJValue? query.
  • Using the .verify(value) method will send the DPOJET:LOCKRJValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOCKRJValue value command.
SCPI Syntax 
- DPOJET:LOCKRJValue <NR3>
- DPOJET:LOCKRJValue?

logging property 

logging: DpojetLogging

Return the DPOJET:LOGging command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging? query.
  • Using the .verify(value) method will send the DPOJET:LOGging? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .measurements: The DPOJET:LOGging:MEASurements command tree.
  • .snapshot: The DPOJET:LOGging:SNAPshot command.
  • .statistics: The DPOJET:LOGging:STATistics command tree.
  • .worstcase: The DPOJET:LOGging:WORSTcase command tree.

meas property 

meas: dict[int, DpojetMeasItem]

Return the DPOJET:MEAS<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ber: The DPOJET:MEAS<x>:BER command tree.
  • .bitcfgmethod: The DPOJET:MEAS<x>:BITCfgmethod command.
  • .bitconfig: The DPOJET:MEAS<x>:BITConfig command tree.
  • .bitpcnt: The DPOJET:MEAS<x>:BITPcnt command.
  • .bittype: The DPOJET:MEAS<x>:BITType command.
  • .busstate: The DPOJET:MEAS<x>:BUSState command tree.
  • .clockrecovery: The DPOJET:MEAS<x>:CLOCKRecovery command tree.
  • .commonmode: The DPOJET:MEAS<x>:COMMONMode command tree.
  • .customgating: The DPOJET:MEAS<x>:CUSTOMGATING command tree.
  • .customname: The DPOJET:MEAS<x>:CUSTomname command.
  • .data: The DPOJET:MEAS<x>:DATA command.
  • .dfe: The DPOJET:MEAS<x>:DFE command tree.
  • .displayname: The DPOJET:MEAS<x>:DISPLAYNAME command.
  • .edge1: The DPOJET:MEAS<x>:EDGE1 command.
  • .edge2: The DPOJET:MEAS<x>:EDGE2 command.
  • .edgeincre: The DPOJET:MEAS<x>:EDGEIncre command.
  • .edges: The DPOJET:MEAS<x>:EDGES command tree.
  • .filters: The DPOJET:MEAS<x>:FILTers command tree.
  • .fromedge: The DPOJET:MEAS<x>:FROMedge command.
  • .highrefvoltage: The DPOJET:MEAS<x>:HIGHREFVoltage command.
  • .logging: The DPOJET:MEAS<x>:LOGging command tree.
  • .lowrefvoltage: The DPOJET:MEAS<x>:LOWREFVoltage command.
  • .margin: The DPOJET:MEAS<x>:MARGIN command tree.
  • .maskoffset: The DPOJET:MEAS<x>:MASKOffset command tree.
  • .maskfile: The DPOJET:MEAS<x>:MASKfile command.
  • .measrange: The DPOJET:MEAS<x>:MEASRange command tree.
  • .measstart: The DPOJET:MEAS<x>:MEASStart command.
  • .n: The DPOJET:MEAS<x>:N command.
  • .name: The DPOJET:MEAS<x>:NAME command.
  • .optical: The DPOJET:MEAS<x>:OPTIcal command tree.
  • .phasenoise: The DPOJET:MEAS<x>:PHASENoise command tree.
  • .plotfiles: The DPOJET:MEAS<x>:PLOTFILES command.
  • .refvoltage: The DPOJET:MEAS<x>:REFVoltage command.
  • .results: The DPOJET:MEAS<x>:RESULts command.
  • .rjdj: The DPOJET:MEAS<x>:RJDJ command tree.
  • .rndn: The DPOJET:MEAS<x>:RNDN command tree.
  • .signaltype: The DPOJET:MEAS<x>:SIGNALType command.
  • .source1: The DPOJET:MEAS<x>:SOUrce1 command.
  • .source2: The DPOJET:MEAS<x>:SOUrce2 command.
  • .ssc: The DPOJET:MEAS<x>:SSC command tree.
  • .timedata: The DPOJET:MEAS<x>:TIMEDATa command.
  • .toedge: The DPOJET:MEAS<x>:TOEdge command.
  • .zoomevent: The DPOJET:MEAS<x>:ZOOMEVENT command.

minbujui property 

minbujui: DpojetMinbujui

Return the DPOJET:MINBUJUI command.

Description
  • This command sets or queries the minimum number of UI for BUJ analysis.
Usage
  • Using the .query() method will send the DPOJET:MINBUJUI? query.
  • Using the .verify(value) method will send the DPOJET:MINBUJUI? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MINBUJUI value command.
SCPI Syntax 
- DPOJET:MINBUJUI <NR3>
- DPOJET:MINBUJUI?

noiseenabled property 

noiseenabled: DpojetNoiseenabled

Return the DPOJET:NOISEENABLED command.

Description
  • This set-only command turns on or off the Noise measurements. Note: Configure
Usage
  • Using the .write(value) method will send the DPOJET:NOISEENABLED value command.
SCPI Syntax 
- DPOJET:NOISEENABLED {ON|OFF|1|0}

nummeas property 

nummeas: DpojetNummeas

Return the DPOJET:NUMMeas command.

Description
  • This query-only command returns the current number of defined measurements.
Usage
  • Using the .query() method will send the DPOJET:NUMMeas? query.
  • Using the .verify(value) method will send the DPOJET:NUMMeas? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:NUMMeas?

numplot property 

numplot: DpojetNumplot

Return the DPOJET:NUMPlot command.

Description
  • This query-only command returns the current number of plots added. If no plots are added, then it returns 0, else returns the total number of plots added between value 1 to 4.
Usage
  • Using the .query() method will send the DPOJET:NUMPlot? query.
  • Using the .verify(value) method will send the DPOJET:NUMPlot? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:NUMPlot?

opticalunittype property 

opticalunittype: DpojetOpticalunittype

Return the DPOJET:OPTICALUNITType command.

Description
  • This command sets or queries the current optical unit-type setting for DPOJET, either Watt, or dBm.
Usage
  • Using the .query() method will send the DPOJET:OPTICALUNITType? query.
  • Using the .verify(value) method will send the DPOJET:OPTICALUNITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:OPTICALUNITType value command.
SCPI Syntax 
- DPOJET:OPTICALUNITType {WATT|DBM}
- DPOJET:OPTICALUNITType?

plot property 

plot: dict[int, DpojetPlotItem]

Return the DPOJET:PLOT<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .bathtub: The DPOJET:PLOT<x>:BATHtub command tree.
  • .bercontour: The DPOJET:PLOT<x>:BERContour command tree.
  • .bereye: The DPOJET:PLOT<x>:BEREye command tree.
  • .compositejitterhist: The DPOJET:PLOT<x>:COMPOSITEJitterhist command tree.
  • .compositenoisehist: The DPOJET:PLOT<x>:COMPOSITENoisehist command tree.
  • .correlatedeye: The DPOJET:PLOT<x>:CORRELATEDEye command tree.
  • .currentuisacquired: The DPOJET:PLOT<x>:CURRENTUISACquired command.
  • .currentuisanalyzed: The DPOJET:PLOT<x>:CURRENTUISANalyzed command.
  • .data: The DPOJET:PLOT<x>:DATA command tree.
  • .exportraw: The DPOJET:PLOT<x>:EXPORTRaw command.
  • .eye: The DPOJET:PLOT<x>:EYE command tree.
  • .histogram: The DPOJET:PLOT<x>:HISTOgram command tree.
  • .noisebathtub: The DPOJET:PLOT<x>:NOISEBATHtub command tree.
  • .pdfeye: The DPOJET:PLOT<x>:PDFEye command tree.
  • .phasenoise: The DPOJET:PLOT<x>:PHASEnoise command tree.
  • .source: The DPOJET:PLOT<x>:SOUrce command.
  • .spectrum: The DPOJET:PLOT<x>:SPECtrum command tree.
  • .totaluisacquired: The DPOJET:PLOT<x>:TOTALUISAcquired command.
  • .totaluisanalyzed: The DPOJET:PLOT<x>:TOTALUISAnalyzed command.
  • .transfer: The DPOJET:PLOT<x>:TRANSfer command tree.
  • .trend: The DPOJET:PLOT<x>:TREND command tree.
  • .type: The DPOJET:PLOT<x>:TYPe command.
  • .vertbathtub: The DPOJET:PLOT<x>:VERTBATHtub command tree.
  • .xunits: The DPOJET:PLOT<x>:XUnits command.
  • .yunits: The DPOJET:PLOT<x>:YUnits command.

population property 

population: DpojetPopulation

Return the DPOJET:POPULATION command tree.

Usage
  • Using the .query() method will send the DPOJET:POPULATION? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .condition: The DPOJET:POPULATION:CONDition command.
  • .limit: The DPOJET:POPULATION:LIMIT command.
  • .limitby: The DPOJET:POPULATION:LIMITBY command.
  • .state: The DPOJET:POPULATION:STATE command.

qualify property 

qualify: DpojetQualify

Return the DPOJET:QUALify command tree.

Usage
  • Using the .query() method will send the DPOJET:QUALify? query.
  • Using the .verify(value) method will send the DPOJET:QUALify? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .active: The DPOJET:QUALify:ACTIVE command.
  • .source: The DPOJET:QUALify:SOUrce command.
  • .state: The DPOJET:QUALify:STATE command.

reflevel property 

reflevel: DpojetReflevel

Return the DPOJET:REFLevel command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevel? query.
  • Using the .verify(value) method will send the DPOJET:REFLevel? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ch: The DPOJET:REFLevel:CH<x> command tree.

reflevels property 

reflevels: DpojetReflevels

Return the DPOJET:REFLevels command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevels? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .autoset: The DPOJET:REFLevels:AUTOset command.
  • .ch: The DPOJET:REFLevels:CH<x> command tree.

report property 

report: DpojetReport

Return the DPOJET:REPORT command.

Description
  • These are set-only commands. EXECute executes a DPOJET report save operation for the currently defined report configuration. APPEnd appends new data to the selected report. Note: Ensure to close the PDF report before append.
Usage
  • Using the .write(value) method will send the DPOJET:REPORT value command.
SCPI Syntax 
- DPOJET:REPORT {EXECute|APPEnd}
Sub-properties
  • .applicationconfig: The DPOJET:REPORT:APPlicationconfig command.
  • .autoincrement: The DPOJET:REPORT:AUTOincrement command.
  • .comments: The DPOJET:REPORT:COMments command.
  • .detailedresults: The DPOJET:REPORT:DETailedresults command.
  • .enablecomments: The DPOJET:REPORT:ENABlecomments command.
  • .getimage: The DPOJET:REPORT:GETIMAGE command.
  • .getimagename: The DPOJET:REPORT:GETIMAGEName command.
  • .getxmlreport: The DPOJET:REPORT:GETXMLReport command.
  • .passfailresults: The DPOJET:REPORT:PASSFailresults command.
  • .plotimages: The DPOJET:REPORT:PLOTimages command.
  • .reportname: The DPOJET:REPORT:REPORTName command.
  • .savewaveforms: The DPOJET:REPORT:SAVEWaveforms command.
  • .setimagepath: The DPOJET:REPORT:SETIMAGEPath command.
  • .setupconfig: The DPOJET:REPORT:SETupconfig command.
  • .state: The DPOJET:REPORT:STATE command.
  • .type: The DPOJET:REPORT:TYPe command.
  • .viewreport: The DPOJET:REPORT:VIEWreport command.

results property 

results: DpojetResults

Return the DPOJET:RESULts command tree.

Usage
  • Using the .query() method will send the DPOJET:RESULts? query.
  • Using the .verify(value) method will send the DPOJET:RESULts? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .getallresults: The DPOJET:RESULts:GETALLResults command.
  • .status: The DPOJET:RESULts:STATus command.
  • .view: The DPOJET:RESULts:VIew command.

save property 

save: DpojetSave

Return the DPOJET:SAVE command.

Description
  • This set-only command saves the specified DPOJET measurement result to the specified ref. For Example: DPOJET:SAVE MEAS4, REF2.
Usage
  • Using the .write(value) method will send the DPOJET:SAVE value command.
SCPI Syntax 
- DPOJET:SAVE {MEAS<x>|REF<x>}

saveallplots property 

saveallplots: DpojetSaveallplots

Return the DPOJET:SAVEALLPLOTS command.

Description
  • Saves all the plots to Reports/Resource folder.
Usage
  • Using the .write() method will send the DPOJET:SAVEALLPLOTS command.
SCPI Syntax 
- DPOJET:SAVEALLPLOTS

setimagetpath property 

setimagetpath: DpojetSetimagetpath

Return the DPOJET:SETIMAGETPath command.

Description
  • This command sets or queries the image path of the DPOJET application.
Usage
  • Using the .query() method will send the DPOJET:SETIMAGETPath? query.
  • Using the .verify(value) method will send the DPOJET:SETIMAGETPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SETIMAGETPath value command.
SCPI Syntax 
- DPOJET:SETIMAGETPath <file string>
- DPOJET:SETIMAGETPath?

setloggingpath property 

setloggingpath: DpojetSetloggingpath

Return the DPOJET:SETLOGGINGPath command.

Description
  • This command sets or queries the Logging path of the DPOJET application.
Usage
  • Using the .query() method will send the DPOJET:SETLOGGINGPath? query.
  • Using the .verify(value) method will send the DPOJET:SETLOGGINGPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SETLOGGINGPath value command.
SCPI Syntax 
- DPOJET:SETLOGGINGPath <file string>
- DPOJET:SETLOGGINGPath?

setreportpath property 

setreportpath: DpojetSetreportpath

Return the DPOJET:SETREPORTPath command.

Description
  • This command sets or queries the Report path of the DPOJET application.
Usage
  • Using the .query() method will send the DPOJET:SETREPORTPath? query.
  • Using the .verify(value) method will send the DPOJET:SETREPORTPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SETREPORTPath value command.
SCPI Syntax 
- DPOJET:SETREPORTPath <file string>
- DPOJET:SETREPORTPath?

showmeaswarning property 

showmeaswarning: DpojetShowmeaswarning

Return the DPOJET:SHOWMEASWARNing command.

Description
  • This sets or queries the visibility of Reference Level Autoset warnings, either on or off.
Usage
  • Using the .query() method will send the DPOJET:SHOWMEASWARNing? query.
  • Using the .verify(value) method will send the DPOJET:SHOWMEASWARNing? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SHOWMEASWARNing value command.
SCPI Syntax 
- DPOJET:SHOWMEASWARNing {1|0}
- DPOJET:SHOWMEASWARNing?

snc property 

snc: DpojetSnc

Return the DPOJET:SNC command tree.

Usage
  • Using the .query() method will send the DPOJET:SNC? query.
  • Using the .verify(value) method will send the DPOJET:SNC? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .activate: The DPOJET:SNC:ACTIvate command.
  • .close: The DPOJET:SNC:CLOse command.

sourceautoset property 

sourceautoset: DpojetSourceautoset

Return the DPOJET:SOURCEAutoset command.

Description
  • This command performs a DPOJET horizontal, vertical, or autoset on both horizontal and vertical for any sources used in current measurements.
Usage
  • Using the .write(value) method will send the DPOJET:SOURCEAutoset value command.
SCPI Syntax 
- DPOJET:SOURCEAutoset {HORizontal|VERTical|BOTH}
Sub-properties
  • .horizontal: The DPOJET:SOURCEAutoset:HORizontal command tree.
  • .state: The DPOJET:SOURCEAutoset:STATE command.

state property 

state: DpojetState

Return the DPOJET:STATE command.

Description
  • This command sets or queries the current measurement state of DPOJET.
Usage
  • Using the .query() method will send the DPOJET:STATE? query.
  • Using the .verify(value) method will send the DPOJET:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:STATE value command.
SCPI Syntax 
- DPOJET:STATE {RUN|SINGLE|RECALC|CLEAR|STOP}
- DPOJET:STATE?

tdcompensation property 

tdcompensation: DpojetTdcompensation

Return the DPOJET:TDCOMPensation command.

Description
  • This command sets or queries the TD compensation state.
Usage
  • Using the .query() method will send the DPOJET:TDCOMPensation? query.
  • Using the .verify(value) method will send the DPOJET:TDCOMPensation? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:TDCOMPensation value command.
SCPI Syntax 
- DPOJET:TDCOMPensation {ON|OFF|1|0}
- DPOJET:TDCOMPensation?

unittype property 

unittype: DpojetUnittype

Return the DPOJET:UNITType command.

Description
  • This command sets or queries the current unit-type setting for DPOJET, either Unit Interval, or seconds.
Usage
  • Using the .query() method will send the DPOJET:UNITType? query.
  • Using the .verify(value) method will send the DPOJET:UNITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:UNITType value command.
SCPI Syntax 
- DPOJET:UNITType {UNITinterval|SEConds}
- DPOJET:UNITType?

version property 

version: DpojetVersion

Return the DPOJET:VERsion command.

Description
  • This query-only command returns the current DPOJET version string.
Usage
  • Using the .query() method will send the DPOJET:VERsion? query.
  • Using the .verify(value) method will send the DPOJET:VERsion? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:VERsion?

vertunittype property 

vertunittype: DpojetVertunittype

Return the DPOJET:VERTUNITType command.

Description
  • This command sets or queries the vertical Unit.
Usage
  • Using the .query() method will send the DPOJET:VERTUNITType? query.
  • Using the .verify(value) method will send the DPOJET:VERTUNITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:VERTUNITType value command.
SCPI Syntax 
- DPOJET:VERTUNITType {UNITamplitude|VOLts}
- DPOJET:VERTUNITType?

DpojetActivate

Bases: SCPICmdWriteNoArguments

The DPOJET:ACTIVATE command.

Description
  • This command launches the DPOJET to active state.
Usage
  • Using the .write() method will send the DPOJET:ACTIVATE command.
SCPI Syntax 
- DPOJET:ACTIVATE

DpojetAddmeas

Bases: SCPICmdWrite

The DPOJET:ADDMeas command.

Description
  • This set-only command adds the specified measurement to the bottom of the current DPOJET list of measurements and will appear in the results summary page.
Usage
  • Using the .write(value) method will send the DPOJET:ADDMeas value command.
SCPI Syntax 
- DPOJET:ADDMeas {PERIod|CCPeriod|FREQuency|NPERiod|PWIdth|NWIdth|PDUTy|NDUTy|PCCDuty|NCCDuty|DATARATE|TIE|RJ|RJDirac|TJber|DJ|DJDirac|PHASENoise|DCD|DDJ|PJ|J2|J9|SRJ|PJrms|SJFREQ|PKPKCLKTJ|PKPKCLKRJ|PKPKCLKDJ|PJRMS|FN|RJH|RJV|PJH|PJV|RN|RNV|RNH|DN|DDN|DDN_1|DDN_0|PN|PNV|PNH|NPN|TNBER|NOISESUMMARY|UNITAMPLITUDE|RISEtime|SETup|HIGHTime|FALLtime|HOLD|LOWTime|SKEW|GATEDSKEW|HEIght|WIDth|MASKHits|WIDTHBer|HEIGHTBer|CYCLEMIN|CYCLEMAX|ACRMS|ACCOMmonmode|COMmonmode|HIGH|TNTratio|HIGHLOW|LOW|VDIFFxovr|RISESLEWrate|FALLSLEWrate|OVERShoot|UNDERShoot|CYCLEPktopk|JITTERSummary|PCIETTXDiffpp|PCIEDEemph|PCIETTx|PCIETTXRise|PCIETTXFall|PCIEUI|PCIETMinpulse|PCIEMEdmxjitter|PCIETRfmismch|PCIESSCFReqdev|PCIEMAXMINratio|PCIESSCPROFile|PCIEVEye|PCIETTXUTJ|PCIETTXUDJDD|PCIETTXUPWTJ|PCIETTXUPWDJDD|PCIETTXDDJ|PCIEVTXBOOST|PCIEVTXNOEQ|PCIEVTXEIEOS|PCIEPS21TX|PCIEACCommonmode|VTXDiffpp|TMINPULSETJ|TCDRslewmax|USBUI|USBACCommonmode|TMINPULSEDJ|QFACTOR|EYELOW|EYEHIGH|TCMDTOCMD|TIMEOUTSIDELEVEL|SSCFREQDEVMAX|SSCFREQDEVMIN|SSCFREQDEV|SSCMODrate|SSCPROfile|USBSSCFREQDEVMAX|USBSSCFREQDEVMIN|USBSSCMODrate|USBSSCPROFile|AUTOFITMaskhits|AOP|EXRATIO|OMA|OPTHIGH|OPTLOW|EYECROSSLEVEL|EYECROSSTIME|EYECROSSPERCENT|DFEEW|DFEEH|DFEEYEDIAGRAM|VWOE|MASKMARGIN|MASKHITRATIO|RIN|RINXOMA|TDEC }

DpojetAddplot

Bases: SCPICmdWrite

The DPOJET:ADDPlot command.

Description
  • This set-only command creates a plot of the specified type on the specified DPOJET measurement. Up to four plots can be created.
Usage
  • Using the .write(value) method will send the DPOJET:ADDPlot value command.
SCPI Syntax 
- DPOJET:ADDPlot {TIMEtrend|DATAarray|HISTOgram|SPECtrum|TRANSfer|PHASEnoise|EYE|WAVEform|BATHtub|QBathtub|QPulsewidth|COMPOSITEJitterhist|NOISEBAthtub|BERContour|CORRELATEDEye|PDFEye|BEREye|COMPOSITENoisehist}, MEAS<x>

DpojetAnalysismethod

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:ANALYSISMETHOD command.

Description
  • This command sets or queries the current analysis method value.
Usage
  • Using the .query() method will send the DPOJET:ANALYSISMETHOD? query.
  • Using the .verify(value) method will send the DPOJET:ANALYSISMETHOD? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:ANALYSISMETHOD value command.
SCPI Syntax 
- DPOJET:ANALYSISMETHOD { JITTEROnly|JITTERNoise }
- DPOJET:ANALYSISMETHOD?

DpojetApplyall

Bases: SCPICmdWrite

The DPOJET:APPLYAll command.

Description
  • This command applies configuration of specified type of the specified DPOJET measurement to all other DPOJET measurements.
Usage
  • Using the .write(value) method will send the DPOJET:APPLYAll value command.
SCPI Syntax 
- DPOJET:APPLYAll {FILTers|CLOCKRecovery|RJDJ}, MEAS<x>

DpojetBitratestate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:BITRatestate command.

Description
  • This command sets or queries the user bitrate state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:BITRatestate? query.
  • Using the .verify(value) method will send the DPOJET:BITRatestate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:BITRatestate value command.
SCPI Syntax 
- DPOJET:BITRatestate {0|1}
- DPOJET:BITRatestate?

DpojetClearallmeas

Bases: SCPICmdWriteNoArguments

The DPOJET:CLEARALLMeas command.

Description
  • This set-only command clears the entire current list of defined measurements in DPOJET.
Usage
  • Using the .write() method will send the DPOJET:CLEARALLMeas command.
SCPI Syntax 
- DPOJET:CLEARALLMeas

DpojetClearallplots

Bases: SCPICmdWriteNoArguments

The DPOJET:CLEARALLPlots command.

Description
  • This set-only command clears the entire current list of defined plots in DPOJET.
Usage
  • Using the .write() method will send the DPOJET:CLEARALLPlots command.
SCPI Syntax 
- DPOJET:CLEARALLPlots

DpojetDataratelimits

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DATAratelimits command.

Description
  • This command sets or queries the reference bitrate for measurement limits.
Usage
  • Using the .query() method will send the DPOJET:DATAratelimits? query.
  • Using the .verify(value) method will send the DPOJET:DATAratelimits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DATAratelimits value command.
SCPI Syntax 
- DPOJET:DATAratelimits <NR3>
- DPOJET:DATAratelimits?

DpojetDeskew

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW command.

Description
  • This command performs a DPOJET deskew operation with the settings specified in DPOJET:DESKEW.
Usage
  • Using the .query() method will send the DPOJET:DESKEW? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW value command.
SCPI Syntax 
- DPOJET:DESKEW {EXEcute}
- DPOJET:DESKEW?
Properties
  • .deskewhysteresis: The DPOJET:DESKEW:DESKEWHysteresis command.
  • .deskewmidlevel: The DPOJET:DESKEW:DESKEWMidlevel command.
  • .deskewchannel: The DPOJET:DESKEW:DESKEWchannel command.
  • .edge: The DPOJET:DESKEW:EDGE command.
  • .maximum: The DPOJET:DESKEW:MAXimum command.
  • .minimum: The DPOJET:DESKEW:MINimum command.
  • .refchannel: The DPOJET:DESKEW:REFChannel command.
  • .refhysteresis: The DPOJET:DESKEW:REFHysteresis command.
  • .refmidlevel: The DPOJET:DESKEW:REFMidlevel command.

deskewchannel property 

deskewchannel: DpojetDeskewDeskewchannel

Return the DPOJET:DESKEW:DESKEWchannel command.

Description
  • This command sets or queries the channel to be deskewed.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:DESKEWchannel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:DESKEWchannel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:DESKEWchannel value command.
SCPI Syntax 
- DPOJET:DESKEW:DESKEWchannel {CH<x>}
- DPOJET:DESKEW:DESKEWchannel?

deskewhysteresis property 

deskewhysteresis: DpojetDeskewDeskewhysteresis

Return the DPOJET:DESKEW:DESKEWHysteresis command.

Description
  • This command sets or queries the deskew channel hysteresis value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:DESKEWHysteresis? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:DESKEWHysteresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:DESKEWHysteresis value command.
SCPI Syntax 
- DPOJET:DESKEW:DESKEWHysteresis <NR3>
- DPOJET:DESKEW:DESKEWHysteresis?

deskewmidlevel property 

deskewmidlevel: DpojetDeskewDeskewmidlevel

Return the DPOJET:DESKEW:DESKEWMidlevel command.

Description
  • This command sets or queries the deskew channel midlevel value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:DESKEWMidlevel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:DESKEWMidlevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:DESKEWMidlevel value command.
SCPI Syntax 
- DPOJET:DESKEW:DESKEWMidlevel <NR3>
- DPOJET:DESKEW:DESKEWMidlevel?

edge property 

edge: DpojetDeskewEdge

Return the DPOJET:DESKEW:EDGE command.

Description
  • This command sets or queries the edge types used when calculating deskew.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:EDGE? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:EDGE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:EDGE value command.
SCPI Syntax 
- DPOJET:DESKEW:EDGE {RISE|FALL|BOTH}
- DPOJET:DESKEW:EDGE?

maximum property 

maximum: DpojetDeskewMaximum

Return the DPOJET:DESKEW:MAXimum command.

Description
  • This command sets or queries the maximum deskew value possible.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:MAXimum? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:MAXimum? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:MAXimum value command.
SCPI Syntax 
- DPOJET:DESKEW:MAXimum <NR3>
- DPOJET:DESKEW:MAXimum?

minimum property 

minimum: DpojetDeskewMinimum

Return the DPOJET:DESKEW:MINimum command.

Description
  • This command sets or queries the minimum deskew value possible.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:MINimum? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:MINimum? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:MINimum value command.
SCPI Syntax 
- DPOJET:DESKEW:MINimum <NR3>
- DPOJET:DESKEW:MINimum?

refchannel property 

refchannel: DpojetDeskewRefchannel

Return the DPOJET:DESKEW:REFChannel command.

Description
  • This command sets or queries the reference channel used for deskew operation.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:REFChannel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:REFChannel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:REFChannel value command.
SCPI Syntax 
- DPOJET:DESKEW:REFChannel {CH1 - CH4}
- DPOJET:DESKEW:REFChannel?

refhysteresis property 

refhysteresis: DpojetDeskewRefhysteresis

Return the DPOJET:DESKEW:REFHysteresis command.

Description
  • This command sets or queries the reference channel hysteresis value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:REFHysteresis? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:REFHysteresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:REFHysteresis value command.
SCPI Syntax 
- DPOJET:DESKEW:REFHysteresis <NR3>
- DPOJET:DESKEW:REFHysteresis?

refmidlevel property 

refmidlevel: DpojetDeskewRefmidlevel

Return the DPOJET:DESKEW:REFMidlevel command.

Description
  • This command sets or queries the reference channel midlevel value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:REFMidlevel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:REFMidlevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:REFMidlevel value command.
SCPI Syntax 
- DPOJET:DESKEW:REFMidlevel <NR3>
- DPOJET:DESKEW:REFMidlevel?

DpojetDeskewDeskewchannel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:DESKEWchannel command.

Description
  • This command sets or queries the channel to be deskewed.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:DESKEWchannel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:DESKEWchannel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:DESKEWchannel value command.
SCPI Syntax 
- DPOJET:DESKEW:DESKEWchannel {CH<x>}
- DPOJET:DESKEW:DESKEWchannel?

DpojetDeskewDeskewhysteresis

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:DESKEWHysteresis command.

Description
  • This command sets or queries the deskew channel hysteresis value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:DESKEWHysteresis? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:DESKEWHysteresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:DESKEWHysteresis value command.
SCPI Syntax 
- DPOJET:DESKEW:DESKEWHysteresis <NR3>
- DPOJET:DESKEW:DESKEWHysteresis?

DpojetDeskewDeskewmidlevel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:DESKEWMidlevel command.

Description
  • This command sets or queries the deskew channel midlevel value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:DESKEWMidlevel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:DESKEWMidlevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:DESKEWMidlevel value command.
SCPI Syntax 
- DPOJET:DESKEW:DESKEWMidlevel <NR3>
- DPOJET:DESKEW:DESKEWMidlevel?

DpojetDeskewEdge

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:EDGE command.

Description
  • This command sets or queries the edge types used when calculating deskew.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:EDGE? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:EDGE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:EDGE value command.
SCPI Syntax 
- DPOJET:DESKEW:EDGE {RISE|FALL|BOTH}
- DPOJET:DESKEW:EDGE?

DpojetDeskewMaximum

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:MAXimum command.

Description
  • This command sets or queries the maximum deskew value possible.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:MAXimum? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:MAXimum? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:MAXimum value command.
SCPI Syntax 
- DPOJET:DESKEW:MAXimum <NR3>
- DPOJET:DESKEW:MAXimum?

DpojetDeskewMinimum

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:MINimum command.

Description
  • This command sets or queries the minimum deskew value possible.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:MINimum? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:MINimum? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:MINimum value command.
SCPI Syntax 
- DPOJET:DESKEW:MINimum <NR3>
- DPOJET:DESKEW:MINimum?

DpojetDeskewRefchannel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:REFChannel command.

Description
  • This command sets or queries the reference channel used for deskew operation.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:REFChannel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:REFChannel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:REFChannel value command.
SCPI Syntax 
- DPOJET:DESKEW:REFChannel {CH1 - CH4}
- DPOJET:DESKEW:REFChannel?

DpojetDeskewRefhysteresis

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:REFHysteresis command.

Description
  • This command sets or queries the reference channel hysteresis value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:REFHysteresis? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:REFHysteresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:REFHysteresis value command.
SCPI Syntax 
- DPOJET:DESKEW:REFHysteresis <NR3>
- DPOJET:DESKEW:REFHysteresis?

DpojetDeskewRefmidlevel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DESKEW:REFMidlevel command.

Description
  • This command sets or queries the reference channel midlevel value.
Usage
  • Using the .query() method will send the DPOJET:DESKEW:REFMidlevel? query.
  • Using the .verify(value) method will send the DPOJET:DESKEW:REFMidlevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DESKEW:REFMidlevel value command.
SCPI Syntax 
- DPOJET:DESKEW:REFMidlevel <NR3>
- DPOJET:DESKEW:REFMidlevel?

DpojetDiracmodel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:DIRacmodel command.

Description
  • This command sets or queries the current dirac model.
Usage
  • Using the .query() method will send the DPOJET:DIRacmodel? query.
  • Using the .verify(value) method will send the DPOJET:DIRacmodel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:DIRacmodel value command.
SCPI Syntax 
- DPOJET:DIRacmodel {FIBREchannel|PCIExpress}
- DPOJET:DIRacmodel?

DpojetExport

Bases: SCPICmdWrite

The DPOJET:EXPORT command.

Description
  • This set-only command saves the specified DPOJET plot to the specified file path. The Format is determined through the filename extension, with a default of png if no extension is specified. Supported extensions include jpeg, jpg, tif, tiff, bmp, emf,.mat,.csv and png.
Usage
  • Using the .write(value) method will send the DPOJET:EXPORT value command.
SCPI Syntax 
- DPOJET:EXPORT {PLOT<x>, <file string>}

DpojetExportraw

Bases: SCPICmdWrite

The DPOJET:EXPORTRaw command.

Description
  • This set-only command saves the raw Eye diagram 2d histogram data to the specified file path. The format is determined through the filename extension. Supported extension include.csv Note: Ensure that the Plot window is open while sending this PI command; else a file will be not generated.
Usage
  • Using the .write(value) method will send the DPOJET:EXPORTRaw value command.
SCPI Syntax 
- DPOJET:EXPORTRaw {PLOT<x>, <file string>}

DpojetGating

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:GATING command.

Description
  • This command sets or queries the gating state.
Usage
  • Using the .query() method will send the DPOJET:GATING? query.
  • Using the .verify(value) method will send the DPOJET:GATING? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:GATING value command.
SCPI Syntax 
- DPOJET:GATING {OFF|ZOOM|CURSOR|MARKS}
- DPOJET:GATING?

DpojetHaltfreerunonlimfail

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:HALTFreerunonlimfail command.

Description
  • This command sets or queries the halt free-run on limit failure (On or Off).
Usage
  • Using the .query() method will send the DPOJET:HALTFreerunonlimfail? query.
  • Using the .verify(value) method will send the DPOJET:HALTFreerunonlimfail? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:HALTFreerunonlimfail value command.
SCPI Syntax 
- DPOJET:HALTFreerunonlimfail {1|0}
- DPOJET:HALTFreerunonlimfail?

DpojetHighperfrendering

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:HIGHPerfrendering command.

Description
  • This command sets or queries the current high-performance eye rendering setting.
Usage
  • Using the .query() method will send the DPOJET:HIGHPerfrendering? query.
  • Using the .verify(value) method will send the DPOJET:HIGHPerfrendering? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:HIGHPerfrendering value command.
SCPI Syntax 
- DPOJET:HIGHPerfrendering <NR1>
- DPOJET:HIGHPerfrendering?

DpojetInterp

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:INTERp command.

Description
  • This command sets or queries the current interpolation model.
Usage
  • Using the .query() method will send the DPOJET:INTERp? query.
  • Using the .verify(value) method will send the DPOJET:INTERp? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:INTERp value command.
SCPI Syntax 
- DPOJET:INTERp {LINear|SINX}
- DPOJET:INTERp?

DpojetJittermode

Bases: SCPICmdRead

The DPOJET:JITtermode command.

Description
  • This command queries the current jitter mode.
Usage
  • Using the .query() method will send the DPOJET:JITtermode? query.
  • Using the .verify(value) method will send the DPOJET:JITtermode? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:JITtermode?

DpojetJittermodel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:JITtermodel command.

Description
  • This command sets the current jitter model.
Usage
  • Using the .query() method will send the DPOJET:JITtermodel? query.
  • Using the .verify(value) method will send the DPOJET:JITtermodel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:JITtermodel value command.
SCPI Syntax 
- DPOJET:JITtermodel {BUJ|Legacy}
- DPOJET:JITtermodel?

DpojetLasterror

Bases: SCPICmdRead

The DPOJET:LASTError command.

Description
  • This query-only command returns the contents of the last pop-up warning dialog box. If no errors have occurred since startup, or since the last call to DPOJET:LASTError?, this command returns an empty string.
Usage
  • Using the .query() method will send the DPOJET:LASTError? query.
  • Using the .verify(value) method will send the DPOJET:LASTError? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:LASTError?

DpojetLimitrise

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LIMITRise command.

Description
  • This command turns on or off the ability to limit Rise/Fall measurements to transition bits only.
Usage
  • Using the .query() method will send the DPOJET:LIMITRise? query.
  • Using the .verify(value) method will send the DPOJET:LIMITRise? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LIMITRise value command.
SCPI Syntax 
- DPOJET:LIMITRise {1|0}
- DPOJET:LIMITRise?

DpojetLimits

Bases: SCPICmdRead

The DPOJET:LIMits command tree.

Usage
  • Using the .query() method will send the DPOJET:LIMits? query.
  • Using the .verify(value) method will send the DPOJET:LIMits? query and raise an AssertionError if the returned value does not match value.
Properties
  • .filename: The DPOJET:LIMits:FILEName command.
  • .state: The DPOJET:LIMits:STATE command.

filename property 

filename: DpojetLimitsFilename

Return the DPOJET:LIMits:FILEName command.

Description
  • This command sets or queries the current limits filename.
Usage
  • Using the .query() method will send the DPOJET:LIMits:FILEName? query.
  • Using the .verify(value) method will send the DPOJET:LIMits:FILEName? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LIMits:FILEName value command.
SCPI Syntax 
- DPOJET:LIMits:FILEName <string>
- DPOJET:LIMits:FILEName?

state property 

state: DpojetLimitsState

Return the DPOJET:LIMits:STATE command.

Description
  • This command turns on or off the pass-fail limit system. Pass-fail status can be queried using the DPOJET:MEAS <x>:RESULTS node.
Usage
  • Using the .query() method will send the DPOJET:LIMits:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LIMits:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LIMits:STATE value command.
SCPI Syntax 
- DPOJET:LIMits:STATE {1|0}
- DPOJET:LIMits:STATE?

DpojetLimitsFilename

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LIMits:FILEName command.

Description
  • This command sets or queries the current limits filename.
Usage
  • Using the .query() method will send the DPOJET:LIMits:FILEName? query.
  • Using the .verify(value) method will send the DPOJET:LIMits:FILEName? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LIMits:FILEName value command.
SCPI Syntax 
- DPOJET:LIMits:FILEName <string>
- DPOJET:LIMits:FILEName?

DpojetLimitsState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LIMits:STATE command.

Description
  • This command turns on or off the pass-fail limit system. Pass-fail status can be queried using the DPOJET:MEAS <x>:RESULTS node.
Usage
  • Using the .query() method will send the DPOJET:LIMits:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LIMits:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LIMits:STATE value command.
SCPI Syntax 
- DPOJET:LIMits:STATE {1|0}
- DPOJET:LIMits:STATE?

DpojetLockrj

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOCKRJ command.

Description
  • This command sets or queries the Lock RJ Value.
Usage
  • Using the .query() method will send the DPOJET:LOCKRJ? query.
  • Using the .verify(value) method will send the DPOJET:LOCKRJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOCKRJ value command.
SCPI Syntax 
- DPOJET:LOCKRJ {1|0 }
- DPOJET:LOCKRJ?

DpojetLockrjvalue

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOCKRJValue command.

Description
  • This command sets or queries the LockRJValue. Inorder to set LockRJValue to be effective, LOCKRJ to be 1 (enabled).
Usage
  • Using the .query() method will send the DPOJET:LOCKRJValue? query.
  • Using the .verify(value) method will send the DPOJET:LOCKRJValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOCKRJValue value command.
SCPI Syntax 
- DPOJET:LOCKRJValue <NR3>
- DPOJET:LOCKRJValue?

DpojetLogging

Bases: SCPICmdRead

The DPOJET:LOGging command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging? query.
  • Using the .verify(value) method will send the DPOJET:LOGging? query and raise an AssertionError if the returned value does not match value.
Properties
  • .measurements: The DPOJET:LOGging:MEASurements command tree.
  • .snapshot: The DPOJET:LOGging:SNAPshot command.
  • .statistics: The DPOJET:LOGging:STATistics command tree.
  • .worstcase: The DPOJET:LOGging:WORSTcase command tree.

measurements property 

measurements: DpojetLoggingMeasurements

Return the DPOJET:LOGging:MEASurements command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging:MEASurements? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:MEASurements? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .folder: The DPOJET:LOGging:MEASurements:FOLDer command.
  • .state: The DPOJET:LOGging:MEASurements:STATE command.

snapshot property 

snapshot: DpojetLoggingSnapshot

Return the DPOJET:LOGging:SNAPshot command.

Description
  • This command performs a DPOJET export of the specified type, either for statistics or measurements.
Usage
  • Using the .write(value) method will send the DPOJET:LOGging:SNAPshot value command.
SCPI Syntax 
- DPOJET:LOGging:SNAPshot {STATistics|MEASurements}

statistics property 

statistics: DpojetLoggingStatistics

Return the DPOJET:LOGging:STATistics command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging:STATistics? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:STATistics? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .filename: The DPOJET:LOGging:STATistics:FILEName command.
  • .state: The DPOJET:LOGging:STATistics:STATE command.

worstcase property 

worstcase: DpojetLoggingWorstcase

Return the DPOJET:LOGging:WORSTcase command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging:WORSTcase? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:WORSTcase? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .folder: The DPOJET:LOGging:WORSTcase:FOLDer command.
  • .state: The DPOJET:LOGging:WORSTcase:STATE command.

DpojetLoggingMeasurements

Bases: SCPICmdRead

The DPOJET:LOGging:MEASurements command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging:MEASurements? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:MEASurements? query and raise an AssertionError if the returned value does not match value.
Properties
  • .folder: The DPOJET:LOGging:MEASurements:FOLDer command.
  • .state: The DPOJET:LOGging:MEASurements:STATE command.

folder property 

folder: DpojetLoggingMeasurementsFolder

Return the DPOJET:LOGging:MEASurements:FOLDer command.

Description
  • This command sets or queries the current folder used for measurement logging.
Usage
  • Using the .query() method will send the DPOJET:LOGging:MEASurements:FOLDer? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:MEASurements:FOLDer? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:MEASurements:FOLDer value command.
SCPI Syntax 
- DPOJET:LOGging:MEASurements:FOLDer <string>
- DPOJET:LOGging:MEASurements:FOLDer?

state property 

state: DpojetLoggingMeasurementsState

Return the DPOJET:LOGging:MEASurements:STATE command.

Description
  • This command turns on or off the future logging of measurements. Individual measurements included in the logging are selected using the DPOJET:MEAS<x>:LOGging node. This parameter turns on or off the entire set of included measurements.
Usage
  • Using the .query() method will send the DPOJET:LOGging:MEASurements:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:MEASurements:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:MEASurements:STATE value command.
SCPI Syntax 
- DPOJET:LOGging:MEASurements:STATE {1|0}
- DPOJET:LOGging:MEASurements:STATE?

DpojetLoggingMeasurementsFolder

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOGging:MEASurements:FOLDer command.

Description
  • This command sets or queries the current folder used for measurement logging.
Usage
  • Using the .query() method will send the DPOJET:LOGging:MEASurements:FOLDer? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:MEASurements:FOLDer? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:MEASurements:FOLDer value command.
SCPI Syntax 
- DPOJET:LOGging:MEASurements:FOLDer <string>
- DPOJET:LOGging:MEASurements:FOLDer?

DpojetLoggingMeasurementsState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOGging:MEASurements:STATE command.

Description
  • This command turns on or off the future logging of measurements. Individual measurements included in the logging are selected using the DPOJET:MEAS<x>:LOGging node. This parameter turns on or off the entire set of included measurements.
Usage
  • Using the .query() method will send the DPOJET:LOGging:MEASurements:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:MEASurements:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:MEASurements:STATE value command.
SCPI Syntax 
- DPOJET:LOGging:MEASurements:STATE {1|0}
- DPOJET:LOGging:MEASurements:STATE?

DpojetLoggingSnapshot

Bases: SCPICmdWrite

The DPOJET:LOGging:SNAPshot command.

Description
  • This command performs a DPOJET export of the specified type, either for statistics or measurements.
Usage
  • Using the .write(value) method will send the DPOJET:LOGging:SNAPshot value command.
SCPI Syntax 
- DPOJET:LOGging:SNAPshot {STATistics|MEASurements}

DpojetLoggingStatistics

Bases: SCPICmdRead

The DPOJET:LOGging:STATistics command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging:STATistics? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:STATistics? query and raise an AssertionError if the returned value does not match value.
Properties
  • .filename: The DPOJET:LOGging:STATistics:FILEName command.
  • .state: The DPOJET:LOGging:STATistics:STATE command.

filename property 

filename: DpojetLoggingStatisticsFilename

Return the DPOJET:LOGging:STATistics:FILEName command.

Description
  • This command sets or queries the current file used for statistics logging.
Usage
  • Using the .query() method will send the DPOJET:LOGging:STATistics:FILEName? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:STATistics:FILEName? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:STATistics:FILEName value command.
SCPI Syntax 
- DPOJET:LOGging:STATistics:FILEName <string>
- DPOJET:LOGging:STATistics:FILEName?

state property 

state: DpojetLoggingStatisticsState

Return the DPOJET:LOGging:STATistics:STATE command.

Description
  • This command turns on or off the future logging of statistics. Individual measurements included in the logging are selected using the DPOJET:MEAS<x>:LOGging node. This parameter turns on or off the entire set of included measurements.
Usage
  • Using the .query() method will send the DPOJET:LOGging:STATistics:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:STATistics:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:STATistics:STATE value command.
SCPI Syntax 
- DPOJET:LOGging:STATistics:STATE {1|0}
- DPOJET:LOGging:STATistics:STATE?

DpojetLoggingStatisticsFilename

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOGging:STATistics:FILEName command.

Description
  • This command sets or queries the current file used for statistics logging.
Usage
  • Using the .query() method will send the DPOJET:LOGging:STATistics:FILEName? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:STATistics:FILEName? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:STATistics:FILEName value command.
SCPI Syntax 
- DPOJET:LOGging:STATistics:FILEName <string>
- DPOJET:LOGging:STATistics:FILEName?

DpojetLoggingStatisticsState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOGging:STATistics:STATE command.

Description
  • This command turns on or off the future logging of statistics. Individual measurements included in the logging are selected using the DPOJET:MEAS<x>:LOGging node. This parameter turns on or off the entire set of included measurements.
Usage
  • Using the .query() method will send the DPOJET:LOGging:STATistics:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:STATistics:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:STATistics:STATE value command.
SCPI Syntax 
- DPOJET:LOGging:STATistics:STATE {1|0}
- DPOJET:LOGging:STATistics:STATE?

DpojetLoggingWorstcase

Bases: SCPICmdRead

The DPOJET:LOGging:WORSTcase command tree.

Usage
  • Using the .query() method will send the DPOJET:LOGging:WORSTcase? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:WORSTcase? query and raise an AssertionError if the returned value does not match value.
Properties
  • .folder: The DPOJET:LOGging:WORSTcase:FOLDer command.
  • .state: The DPOJET:LOGging:WORSTcase:STATE command.

folder property 

folder: DpojetLoggingWorstcaseFolder

Return the DPOJET:LOGging:WORSTcase:FOLDer command.

Description
  • This command sets or queries the current folder used for worst case logging. Note: Waveform filenames generated while worst case logging is on will follow the syntax of ‘Measurement Name’-‘Source’_Min1.wfm and ‘Measurement Name’-‘Source’_Max1.wfm, For example: Period1-Ch1_Max1.wfm, Period1-Ch1_Min1.wfm, Rise Time1-Ch1_Max1.wfm, Rise Time1-Ch1_Min1.wfm.
Usage
  • Using the .query() method will send the DPOJET:LOGging:WORSTcase:FOLDer? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:WORSTcase:FOLDer? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:WORSTcase:FOLDer value command.
SCPI Syntax 
- DPOJET:LOGging:WORSTcase:FOLDer <string>
- DPOJET:LOGging:WORSTcase:FOLDer?

state property 

state: DpojetLoggingWorstcaseState

Return the DPOJET:LOGging:WORSTcase:STATE command.

Description
  • This command turns on or off the future logging of worst case waveforms. Individual measurements included in the logging are selected using the DPOJET:MEAS<x>:LOGging node. This parameter turns on or off the entire set of included measurements.
Usage
  • Using the .query() method will send the DPOJET:LOGging:WORSTcase:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:WORSTcase:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:WORSTcase:STATE value command.
SCPI Syntax 
- DPOJET:LOGging:WORSTcase:STATE {1|0}
- DPOJET:LOGging:WORSTcase:STATE?

DpojetLoggingWorstcaseFolder

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOGging:WORSTcase:FOLDer command.

Description
  • This command sets or queries the current folder used for worst case logging. Note: Waveform filenames generated while worst case logging is on will follow the syntax of ‘Measurement Name’-‘Source’_Min1.wfm and ‘Measurement Name’-‘Source’_Max1.wfm, For example: Period1-Ch1_Max1.wfm, Period1-Ch1_Min1.wfm, Rise Time1-Ch1_Max1.wfm, Rise Time1-Ch1_Min1.wfm.
Usage
  • Using the .query() method will send the DPOJET:LOGging:WORSTcase:FOLDer? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:WORSTcase:FOLDer? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:WORSTcase:FOLDer value command.
SCPI Syntax 
- DPOJET:LOGging:WORSTcase:FOLDer <string>
- DPOJET:LOGging:WORSTcase:FOLDer?

DpojetLoggingWorstcaseState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:LOGging:WORSTcase:STATE command.

Description
  • This command turns on or off the future logging of worst case waveforms. Individual measurements included in the logging are selected using the DPOJET:MEAS<x>:LOGging node. This parameter turns on or off the entire set of included measurements.
Usage
  • Using the .query() method will send the DPOJET:LOGging:WORSTcase:STATE? query.
  • Using the .verify(value) method will send the DPOJET:LOGging:WORSTcase:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:LOGging:WORSTcase:STATE value command.
SCPI Syntax 
- DPOJET:LOGging:WORSTcase:STATE {1|0}
- DPOJET:LOGging:WORSTcase:STATE?

DpojetMeasItem

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The DPOJET:MEAS<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ber: The DPOJET:MEAS<x>:BER command tree.
  • .bitcfgmethod: The DPOJET:MEAS<x>:BITCfgmethod command.
  • .bitconfig: The DPOJET:MEAS<x>:BITConfig command tree.
  • .bitpcnt: The DPOJET:MEAS<x>:BITPcnt command.
  • .bittype: The DPOJET:MEAS<x>:BITType command.
  • .busstate: The DPOJET:MEAS<x>:BUSState command tree.
  • .clockrecovery: The DPOJET:MEAS<x>:CLOCKRecovery command tree.
  • .commonmode: The DPOJET:MEAS<x>:COMMONMode command tree.
  • .customgating: The DPOJET:MEAS<x>:CUSTOMGATING command tree.
  • .customname: The DPOJET:MEAS<x>:CUSTomname command.
  • .data: The DPOJET:MEAS<x>:DATA command.
  • .dfe: The DPOJET:MEAS<x>:DFE command tree.
  • .displayname: The DPOJET:MEAS<x>:DISPLAYNAME command.
  • .edge1: The DPOJET:MEAS<x>:EDGE1 command.
  • .edge2: The DPOJET:MEAS<x>:EDGE2 command.
  • .edgeincre: The DPOJET:MEAS<x>:EDGEIncre command.
  • .edges: The DPOJET:MEAS<x>:EDGES command tree.
  • .filters: The DPOJET:MEAS<x>:FILTers command tree.
  • .fromedge: The DPOJET:MEAS<x>:FROMedge command.
  • .highrefvoltage: The DPOJET:MEAS<x>:HIGHREFVoltage command.
  • .logging: The DPOJET:MEAS<x>:LOGging command tree.
  • .lowrefvoltage: The DPOJET:MEAS<x>:LOWREFVoltage command.
  • .margin: The DPOJET:MEAS<x>:MARGIN command tree.
  • .maskoffset: The DPOJET:MEAS<x>:MASKOffset command tree.
  • .maskfile: The DPOJET:MEAS<x>:MASKfile command.
  • .measrange: The DPOJET:MEAS<x>:MEASRange command tree.
  • .measstart: The DPOJET:MEAS<x>:MEASStart command.
  • .n: The DPOJET:MEAS<x>:N command.
  • .name: The DPOJET:MEAS<x>:NAME command.
  • .optical: The DPOJET:MEAS<x>:OPTIcal command tree.
  • .phasenoise: The DPOJET:MEAS<x>:PHASENoise command tree.
  • .plotfiles: The DPOJET:MEAS<x>:PLOTFILES command.
  • .refvoltage: The DPOJET:MEAS<x>:REFVoltage command.
  • .results: The DPOJET:MEAS<x>:RESULts command.
  • .rjdj: The DPOJET:MEAS<x>:RJDJ command tree.
  • .rndn: The DPOJET:MEAS<x>:RNDN command tree.
  • .signaltype: The DPOJET:MEAS<x>:SIGNALType command.
  • .source1: The DPOJET:MEAS<x>:SOUrce1 command.
  • .source2: The DPOJET:MEAS<x>:SOUrce2 command.
  • .ssc: The DPOJET:MEAS<x>:SSC command tree.
  • .timedata: The DPOJET:MEAS<x>:TIMEDATa command.
  • .toedge: The DPOJET:MEAS<x>:TOEdge command.
  • .zoomevent: The DPOJET:MEAS<x>:ZOOMEVENT command.

ber property 

ber: DpojetMeasItemBer

Return the DPOJET:MEAS<x>:BER command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BER? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .targetber: The DPOJET:MEAS<x>:BER:TARGETBER command.

bitcfgmethod property 

bitcfgmethod: DpojetMeasItemBitcfgmethod

Return the DPOJET:MEAS<x>:BITCfgmethod command.

Description
  • This command sets or queries the measurement bit configure method.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITCfgmethod? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITCfgmethod? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITCfgmethod value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITCfgmethod {MEAN|MODE}
- DPOJET:MEAS<x>:BITCfgmethod?

bitconfig property 

bitconfig: DpojetMeasItemBitconfig

Return the DPOJET:MEAS<x>:BITConfig command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .absrelstate: The DPOJET:MEAS<x>:BITConfig:ABSRELstate command.
  • .endpercent: The DPOJET:MEAS<x>:BITConfig:ENDPercent command.
  • .numbins: The DPOJET:MEAS<x>:BITConfig:NUMBins command.
  • .startpercent: The DPOJET:MEAS<x>:BITConfig:STARTPercent command.

bitpcnt property 

bitpcnt: DpojetMeasItemBitpcnt

Return the DPOJET:MEAS<x>:BITPcnt command.

Description
  • This command sets or queries the percentage value to be measured for the Bit type selected.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITPcnt? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITPcnt? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITPcnt value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITPcnt <NR3>
- DPOJET:MEAS<x>:BITPcnt?

bittype property 

bittype: DpojetMeasItemBittype

Return the DPOJET:MEAS<x>:BITType command.

Description
  • This command sets or queries the measurement bit type setting.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITType {ALLBits|NONTRANsition|TRANsition}
- DPOJET:MEAS<x>:BITType?

busstate property 

busstate: DpojetMeasItemBusstate

Return the DPOJET:MEAS<x>:BUSState command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .clockpolarity: The DPOJET:MEAS<x>:BUSState:CLOCKPolarity command.
  • .frompattern: The DPOJET:MEAS<x>:BUSState:FROMPattern command.
  • .fromsymbol: The DPOJET:MEAS<x>:BUSState:FROMSymbol command.
  • .measurefrom: The DPOJET:MEAS<x>:BUSState:MEASUREFrom command.
  • .measureto: The DPOJET:MEAS<x>:BUSState:MEASURETO command.
  • .measuretype: The DPOJET:MEAS<x>:BUSState:MEASUREType command.
  • .topattern: The DPOJET:MEAS<x>:BUSState:TOPattern command.
  • .tosymbol: The DPOJET:MEAS<x>:BUSState:TOSymbol command.

clockrecovery property 

clockrecovery: DpojetMeasItemClockrecovery

Return the DPOJET:MEAS<x>:CLOCKRecovery command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .bhvrstandard: The DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard command.
  • .bwtype: The DPOJET:MEAS<x>:CLOCKRecovery:BWType command.
  • .clockbitrate: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate command.
  • .clockfrequency: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.
  • .clockmultiplier: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.
  • .clockpath: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath command.
  • .damping: The DPOJET:MEAS<x>:CLOCKRecovery:DAMPing command.
  • .datarate: The DPOJET:MEAS<x>:CLOCKRecovery:DATARate command.
  • .loopbandwidth: The DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.
  • .meanautocalculate: The DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.
  • .method: The DPOJET:MEAS<x>:CLOCKRecovery:METHod command.
  • .model: The DPOJET:MEAS<x>:CLOCKRecovery:MODel command.
  • .nominaloffset: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.
  • .pattern: The DPOJET:MEAS<x>:CLOCKRecovery:PATTern command.
  • .standard: The DPOJET:MEAS<x>:CLOCKRecovery:STAndard command.

commonmode property 

commonmode: DpojetMeasItemCommonmode

Return the DPOJET:MEAS<x>:COMMONMode command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:COMMONMode? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:COMMONMode? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .filters: The DPOJET:MEAS<x>:COMMONMode:FILTers command tree.

customgating property 

customgating: DpojetMeasItemCustomgating

Return the DPOJET:MEAS<x>:CUSTOMGATING command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .fromedge: The DPOJET:MEAS<x>:CUSTOMGATING:FROMedge command.
  • .measurementedge: The DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge command.
  • .source1gate: The DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE command.
  • .source2gate: The DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE command.
  • .toedge: The DPOJET:MEAS<x>:CUSTOMGATING:TOedge command.

customname property 

customname: DpojetMeasItemCustomname

Return the DPOJET:MEAS<x>:CUSTomname command.

Description
  • This command sets or queries the custom measurement name for the measurement in slot x.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTomname? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTomname? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTomname value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTomname <string>
- DPOJET:MEAS<x>:CUSTomname?

data property 

data: DpojetMeasItemData

Return the DPOJET:MEAS<x>:DATA command.

Description
  • This query-only command returns the measurement data. This is similar to the curve query, where the output is in the format #, where is the number of bytes. For Example: If =500, =3 is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DATA? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DATA? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:DATA?

dfe property 

dfe: DpojetMeasItemDfe

Return the DPOJET:MEAS<x>:DFE command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .absolutetimestate: The DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState command.
  • .absolutetimevalue: The DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue command.
  • .absolutevoltagestate: The DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState command.
  • .absolutevoltagevalue: The DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue command.
  • .delaycompensation: The DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION command.
  • .manualdelay: The DPOJET:MEAS<x>:DFE:MANUALDELAY command.
  • .measatpercent: The DPOJET:MEAS<x>:DFE:MEASatpercent command.
  • .resolution: The DPOJET:MEAS<x>:DFE:RESOlution command.
  • .tapstate: The DPOJET:MEAS<x>:DFE:TAPState command.
  • .tapvalue: The DPOJET:MEAS<x>:DFE:TAPValue command.

displayname property 

displayname: DpojetMeasItemDisplayname

Return the DPOJET:MEAS<x>:DISPLAYNAME command.

Description
  • This command queries the UI name of the measurement x in the measurement table. Note: If the measurement UI name has special character δ, then it is displayed as d.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DISPLAYNAME? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DISPLAYNAME? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:DISPLAYNAME?

edge1 property 

edge1: DpojetMeasItemEdge1

Return the DPOJET:MEAS<x>:EDGE1 command.

Description
  • This command sets or queries the Source1 edge type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGE1? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGE1? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGE1 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGE1 {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:EDGE1?

edge2 property 

edge2: DpojetMeasItemEdge2

Return the DPOJET:MEAS<x>:EDGE2 command.

Description
  • This command sets or queries the Source2 edge type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGE2? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGE2? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGE2 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGE2 {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:EDGE2?

edgeincre property 

edgeincre: DpojetMeasItemEdgeincre

Return the DPOJET:MEAS<x>:EDGEIncre command.

Description
  • This command sets or queries the measurement edge increment value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGEIncre? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGEIncre? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGEIncre value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGEIncre <NR3>
- DPOJET:MEAS<x>:EDGEIncre?

edges property 

edges: DpojetMeasItemEdges

Return the DPOJET:MEAS<x>:EDGES command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .eyeheightstate: The DPOJET:MEAS<x>:EDGES:EYEHeightstate command.
  • .fromlevel: The DPOJET:MEAS<x>:EDGES:FROMLevel command.
  • .level: The DPOJET:MEAS<x>:EDGES:LEVel command.
  • .slewratetechnique: The DPOJET:MEAS<x>:EDGES:SLEWRATETechnique command.
  • .subratedivisor: The DPOJET:MEAS<x>:EDGES:SUBRATEDivisor command.
  • .tolevel: The DPOJET:MEAS<x>:EDGES:TOLevel command.
  • .userdefinedvoltage: The DPOJET:MEAS<x>:EDGES:USERDefinedvoltage command.
  • .voltagestate: The DPOJET:MEAS<x>:EDGES:VOLTAGEState command.

filters property 

filters: DpojetMeasItemFilters

Return the DPOJET:MEAS<x>:FILTers command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .blankingtime: The DPOJET:MEAS<x>:FILTers:BLANKingtime command.
  • .highpass: The DPOJET:MEAS<x>:FILTers:HIGHPass command tree.
  • .lowpass: The DPOJET:MEAS<x>:FILTers:LOWPass command tree.
  • .ramptime: The DPOJET:MEAS<x>:FILTers:RAMPtime command.
  • .sjbandwidth: The DPOJET:MEAS<x>:FILTers:SJBAndwidth command.
  • .sjfrequency: The DPOJET:MEAS<x>:FILTers:SJFRequency command.

fromedge property 

fromedge: DpojetMeasItemFromedge

Return the DPOJET:MEAS<x>:FROMedge command.

Description
  • This command sets the FROMedge value for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FROMedge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FROMedge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FROMedge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:FROMedge?

highrefvoltage property 

highrefvoltage: DpojetMeasItemHighrefvoltage

Return the DPOJET:MEAS<x>:HIGHREFVoltage command.

Description
  • This command sets or queries the high reference voltage value for the selected configuration.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:HIGHREFVoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:HIGHREFVoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:HIGHREFVoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:HIGHREFVoltage <NR3>
- DPOJET:MEAS<x>:HIGHREFVoltage?

logging property 

logging: DpojetMeasItemLogging

Return the DPOJET:MEAS<x>:LOGging command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .measurements: The DPOJET:MEAS<x>:LOGging:MEASurements command tree.
  • .statistics: The DPOJET:MEAS<x>:LOGging:STATistics command tree.
  • .worstcase: The DPOJET:MEAS<x>:LOGging:WORSTcase command tree.

lowrefvoltage property 

lowrefvoltage: DpojetMeasItemLowrefvoltage

Return the DPOJET:MEAS<x>:LOWREFVoltage command.

Description
  • This command sets or queries the low reference voltage value for the selected configuration.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOWREFVoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOWREFVoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOWREFVoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOWREFVoltage <NR3>
- DPOJET:MEAS<x>:LOWREFVoltage?

margin property 

margin: DpojetMeasItemMargin

Return the DPOJET:MEAS<x>:MARGIN command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .hitcountvalue: The DPOJET:MEAS<x>:MARGIN:HITCOUNTValue command.
  • .hitratiostate: The DPOJET:MEAS<x>:MARGIN:HITRATIOState command.
  • .hitratiovalue: The DPOJET:MEAS<x>:MARGIN:HITRATIOValue command.
  • .resolution: The DPOJET:MEAS<x>:MARGIN:RESOlution command.

maskfile property 

maskfile: DpojetMeasItemMaskfile

Return the DPOJET:MEAS<x>:MASKfile command.

Description
  • This command sets or queries the current mask file name.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKfile? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKfile? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MASKfile value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKfile <string>
- DPOJET:MEAS<x>:MASKfile?

maskoffset property 

maskoffset: DpojetMeasItemMaskoffset

Return the DPOJET:MEAS<x>:MASKOffset command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .horizontal: The DPOJET:MEAS<x>:MASKOffset:HORizontal command tree.

measrange property 

measrange: DpojetMeasItemMeasrange

Return the DPOJET:MEAS<x>:MEASRange command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .max: The DPOJET:MEAS<x>:MEASRange:MAX command.
  • .min: The DPOJET:MEAS<x>:MEASRange:MIN command.
  • .state: The DPOJET:MEAS<x>:MEASRange:STATE command.

measstart property 

measstart: DpojetMeasItemMeasstart

Return the DPOJET:MEAS<x>:MEASStart command.

Description
  • This command sets or queries the measurement start value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASStart? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASStart? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASStart value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASStart <NR3>
- DPOJET:MEAS<x>:MEASStart?

n property 

n: DpojetMeasItemN

Return the DPOJET:MEAS<x>:N command.

Description
  • This command sets or queries the measurement N value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:N? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:N? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:N value command.
SCPI Syntax 
- DPOJET:MEAS<x>:N <NR3>
- DPOJET:MEAS<x>:N?

name property 

name: DpojetMeasItemName

Return the DPOJET:MEAS<x>:NAME command.

Description
  • This query-only command returns the measurement name for the measurement in slot x. For measurements that include 16-bit characters in their UI names, such as DJDirac, the string returned will contain question marks where the UI contains nontext characters.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:NAME? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:NAME? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:NAME?

optical property 

optical: DpojetMeasItemOptical

Return the DPOJET:MEAS<x>:OPTIcal command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .bandwidth: The DPOJET:MEAS<x>:OPTIcal:BANDWIDth command.
  • .btfilter: The DPOJET:MEAS<x>:OPTIcal:BTFILTEr command.
  • .ffetaps: The DPOJET:MEAS<x>:OPTIcal:FFETAPS command.
  • .scopern: The DPOJET:MEAS<x>:OPTIcal:SCOPERN command.
  • .targetber: The DPOJET:MEAS<x>:OPTIcal:TARGETBer command.
  • .wfmtype: The DPOJET:MEAS<x>:OPTIcal:WFMTYpe command.

phasenoise property 

phasenoise: DpojetMeasItemPhasenoise

Return the DPOJET:MEAS<x>:PHASENoise command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PHASENoise? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PHASENoise? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .highlimit: The DPOJET:MEAS<x>:PHASENoise:HIGHLimit command.
  • .lowlimit: The DPOJET:MEAS<x>:PHASENoise:LOWLimit command.

plotfiles property 

plotfiles: DpojetMeasItemPlotfiles

Return the DPOJET:MEAS<x>:PLOTFILES command.

Description
  • The query-only command returns plot file paths of a given measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PLOTFILES? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PLOTFILES? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:PLOTFILES?

refvoltage property 

refvoltage: DpojetMeasItemRefvoltage

Return the DPOJET:MEAS<x>:REFVoltage command.

Description
  • This command sets or queries the reference voltage for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:REFVoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:REFVoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:REFVoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:REFVoltage {100|—100}
- DPOJET:MEAS<x>:REFVoltage?

results property 

results: DpojetMeasItemResults

Return the DPOJET:MEAS<x>:RESULts command.

Description
  • This query-only command returns the measurement branch for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts?
Sub-properties
  • .allacqs: The DPOJET:MEAS<x>:RESULts:ALLAcqs command.
  • .currentacq: The DPOJET:MEAS<x>:RESULts:CURRentacq command tree.
  • .getall: The DPOJET:MEAS<x>:RESULts:GETAll command.
  • .status: The DPOJET:MEAS<x>:RESULts:STATus command.
  • .view: The DPOJET:MEAS<x>:RESULts:VIew command.

rjdj property 

rjdj: DpojetMeasItemRjdj

Return the DPOJET:MEAS<x>:RJDJ command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ber: The DPOJET:MEAS<x>:RJDJ:BER command.
  • .detectplen: The DPOJET:MEAS<x>:RJDJ:DETECTPLEN command.
  • .ncmode: The DPOJET:MEAS<x>:RJDJ:NCMODe command.
  • .patlen: The DPOJET:MEAS<x>:RJDJ:PATLen command.
  • .scopern: The DPOJET:MEAS<x>:RJDJ:SCOPERN command.
  • .sncrefid: The DPOJET:MEAS<x>:RJDJ:SNCREFID command.
  • .type: The DPOJET:MEAS<x>:RJDJ:TYPe command.
  • .windowlength: The DPOJET:MEAS<x>:RJDJ:WINDOwlength command.

rndn property 

rndn: DpojetMeasItemRndn

Return the DPOJET:MEAS<x>:RNDN command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .autodetectpattern: The DPOJET:MEAS<x>:RNDN:AUTODETECTpattern command.
  • .ber: The DPOJET:MEAS<x>:RNDN:BER command.
  • .ncmode: The DPOJET:MEAS<x>:RNDN:NCMODe command.
  • .patlen: The DPOJET:MEAS<x>:RNDN:PATLen command.
  • .scopern: The DPOJET:MEAS<x>:RNDN:SCOPERN command.
  • .sncrefid: The DPOJET:MEAS<x>:RNDN:SNCREFID command.
  • .type: The DPOJET:MEAS<x>:RNDN:TYPe command.
  • .windowlength: The DPOJET:MEAS<x>:RNDN:WINDOwlength command.

signaltype property 

signaltype: DpojetMeasItemSignaltype

Return the DPOJET:MEAS<x>:SIGNALType command.

Description
  • This command sets the signal type for various measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SIGNALType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SIGNALType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SIGNALType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- DPOJET:MEAS<x>:SIGNALType?

source1 property 

source1: DpojetMeasItemSource1

Return the DPOJET:MEAS<x>:SOUrce1 command.

Description
  • This command sets or queries the Source1 value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SOUrce1? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SOUrce1 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SOUrce1 {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|D0 — D15}
- DPOJET:MEAS<x>:SOUrce1?

source2 property 

source2: DpojetMeasItemSource2

Return the DPOJET:MEAS<x>:SOUrce2 command.

Description
  • This command sets or queries the Source2 value. May return NONE for single-source measurement. Source2 may be the second source used in dual-source measurements, or the clock source in others. In either case, it is always the same as the rightmost displayed source on the UI.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SOUrce2? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SOUrce2? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SOUrce2 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SOUrce2 {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|D0 — D15}
- DPOJET:MEAS<x>:SOUrce2?

ssc property 

ssc: DpojetMeasItemSsc

Return the DPOJET:MEAS<x>:SSC command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .nominalfreq: The DPOJET:MEAS<x>:SSC:NOMinalfreq command tree.

timedata property 

timedata: DpojetMeasItemTimedata

Return the DPOJET:MEAS<x>:TIMEDATa command.

Description
  • This query-only command returns the measurement time data. It is similar to the curve query, where the output is in the format #, where is the number of bytes. For Example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: Time data is not available for all measurements. For Example: Scalar measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:TIMEDATa? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:TIMEDATa? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:TIMEDATa?

toedge property 

toedge: DpojetMeasItemToedge

Return the DPOJET:MEAS<x>:TOEdge command.

Description
  • This command sets the TOEdge value for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:TOEdge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:TOEdge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:TOEdge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:TOEdge {SAMEas|OPPositeas}
- DPOJET:MEAS<x>:TOEdge?

zoomevent property 

zoomevent: DpojetMeasItemZoomevent

Return the DPOJET:MEAS<x>:ZOOMEVENT command.

Description
  • This command zooms into the waveform where a max/min value occurs in a measurement.
Usage
  • Using the .write(value) method will send the DPOJET:MEAS<x>:ZOOMEVENT value command.
SCPI Syntax 
- DPOJET:MEAS<x>:ZOOMEVENT {MAX|MIN}

DpojetMeasItemBer

Bases: SCPICmdRead

The DPOJET:MEAS<x>:BER command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BER? query and raise an AssertionError if the returned value does not match value.
Properties
  • .targetber: The DPOJET:MEAS<x>:BER:TARGETBER command.

targetber property 

targetber: DpojetMeasItemBerTargetber

Return the DPOJET:MEAS<x>:BER:TARGETBER command.

Description
  • This command sets or queries the BER value. Note: This command is different from DPOJET:MEAS:RJDJ:BER whose configuration parameter exist in RJDJ tab.This command is different from DPOJET:MEAS:RNDN:BER whose configuration parameter exist in RNDN tab.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BER:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BER:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BER:TARGETBER value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BER:TARGETBER <NR3>
- DPOJET:MEAS<x>:BER:TARGETBER?

DpojetMeasItemBerTargetber

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BER:TARGETBER command.

Description
  • This command sets or queries the BER value. Note: This command is different from DPOJET:MEAS:RJDJ:BER whose configuration parameter exist in RJDJ tab.This command is different from DPOJET:MEAS:RNDN:BER whose configuration parameter exist in RNDN tab.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BER:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BER:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BER:TARGETBER value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BER:TARGETBER <NR3>
- DPOJET:MEAS<x>:BER:TARGETBER?

DpojetMeasItemBitcfgmethod

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BITCfgmethod command.

Description
  • This command sets or queries the measurement bit configure method.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITCfgmethod? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITCfgmethod? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITCfgmethod value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITCfgmethod {MEAN|MODE}
- DPOJET:MEAS<x>:BITCfgmethod?

DpojetMeasItemBitconfig

Bases: SCPICmdRead

The DPOJET:MEAS<x>:BITConfig command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig? query and raise an AssertionError if the returned value does not match value.
Properties
  • .absrelstate: The DPOJET:MEAS<x>:BITConfig:ABSRELstate command.
  • .endpercent: The DPOJET:MEAS<x>:BITConfig:ENDPercent command.
  • .numbins: The DPOJET:MEAS<x>:BITConfig:NUMBins command.
  • .startpercent: The DPOJET:MEAS<x>:BITConfig:STARTPercent command.

absrelstate property 

absrelstate: DpojetMeasItemBitconfigAbsrelstate

Return the DPOJET:MEAS<x>:BITConfig:ABSRELstate command.

Description
  • This command sets or queries the user absolute/relative state, either on or off. 0-> sets the Absolute 1-> sets the Relative
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:ABSRELstate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:ABSRELstate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:ABSRELstate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:ABSRELstate {0|1}
- DPOJET:MEAS<x>:BITConfig:ABSRELstate?

endpercent property 

endpercent: DpojetMeasItemBitconfigEndpercent

Return the DPOJET:MEAS<x>:BITConfig:ENDPercent command.

Description
  • This command sets or queries the ending percentage of the bit to measure.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:ENDPercent? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:ENDPercent? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:ENDPercent value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:ENDPercent <NR3>
- DPOJET:MEAS<x>:BITConfig:ENDPercent?

numbins property 

numbins: DpojetMeasItemBitconfigNumbins

Return the DPOJET:MEAS<x>:BITConfig:NUMBins command.

Description
  • This command sets or queries the number of bins per window.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:NUMBins value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:NUMBins <NR3>
- DPOJET:MEAS<x>:BITConfig:NUMBins?

startpercent property 

startpercent: DpojetMeasItemBitconfigStartpercent

Return the DPOJET:MEAS<x>:BITConfig:STARTPercent command.

Description
  • This command sets or queries the starting percentage of the bit to measure.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:STARTPercent? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:STARTPercent? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:STARTPercent value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:STARTPercent <NR3>
- DPOJET:MEAS<x>:BITConfig:STARTPercent?

DpojetMeasItemBitconfigAbsrelstate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BITConfig:ABSRELstate command.

Description
  • This command sets or queries the user absolute/relative state, either on or off. 0-> sets the Absolute 1-> sets the Relative
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:ABSRELstate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:ABSRELstate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:ABSRELstate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:ABSRELstate {0|1}
- DPOJET:MEAS<x>:BITConfig:ABSRELstate?

DpojetMeasItemBitconfigEndpercent

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BITConfig:ENDPercent command.

Description
  • This command sets or queries the ending percentage of the bit to measure.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:ENDPercent? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:ENDPercent? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:ENDPercent value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:ENDPercent <NR3>
- DPOJET:MEAS<x>:BITConfig:ENDPercent?

DpojetMeasItemBitconfigNumbins

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BITConfig:NUMBins command.

Description
  • This command sets or queries the number of bins per window.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:NUMBins value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:NUMBins <NR3>
- DPOJET:MEAS<x>:BITConfig:NUMBins?

DpojetMeasItemBitconfigStartpercent

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BITConfig:STARTPercent command.

Description
  • This command sets or queries the starting percentage of the bit to measure.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITConfig:STARTPercent? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITConfig:STARTPercent? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITConfig:STARTPercent value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITConfig:STARTPercent <NR3>
- DPOJET:MEAS<x>:BITConfig:STARTPercent?

DpojetMeasItemBitpcnt

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BITPcnt command.

Description
  • This command sets or queries the percentage value to be measured for the Bit type selected.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITPcnt? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITPcnt? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITPcnt value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITPcnt <NR3>
- DPOJET:MEAS<x>:BITPcnt?

DpojetMeasItemBittype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BITType command.

Description
  • This command sets or queries the measurement bit type setting.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BITType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BITType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BITType {ALLBits|NONTRANsition|TRANsition}
- DPOJET:MEAS<x>:BITType?

DpojetMeasItemBusstate

Bases: SCPICmdRead

The DPOJET:MEAS<x>:BUSState command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState? query and raise an AssertionError if the returned value does not match value.
Properties
  • .clockpolarity: The DPOJET:MEAS<x>:BUSState:CLOCKPolarity command.
  • .frompattern: The DPOJET:MEAS<x>:BUSState:FROMPattern command.
  • .fromsymbol: The DPOJET:MEAS<x>:BUSState:FROMSymbol command.
  • .measurefrom: The DPOJET:MEAS<x>:BUSState:MEASUREFrom command.
  • .measureto: The DPOJET:MEAS<x>:BUSState:MEASURETO command.
  • .measuretype: The DPOJET:MEAS<x>:BUSState:MEASUREType command.
  • .topattern: The DPOJET:MEAS<x>:BUSState:TOPattern command.
  • .tosymbol: The DPOJET:MEAS<x>:BUSState:TOSymbol command.

clockpolarity property 

clockpolarity: DpojetMeasItemBusstateClockpolarity

Return the DPOJET:MEAS<x>:BUSState:CLOCKPolarity command.

Description
  • This command sets or queries the clock polarity for the clock edge.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:CLOCKPolarity? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:CLOCKPolarity? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:CLOCKPolarity value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:CLOCKPolarity {RISING|FALLING}
- DPOJET:MEAS<x>:BUSState:CLOCKPolarity?

frompattern property 

frompattern: DpojetMeasItemBusstateFrompattern

Return the DPOJET:MEAS<x>:BUSState:FROMPattern command.

Description
  • This command sets or queries the Pattern from which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:FROMPattern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:FROMPattern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:FROMPattern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:FROMPattern <string>
- DPOJET:MEAS<x>:BUSState:FROMPattern?

fromsymbol property 

fromsymbol: DpojetMeasItemBusstateFromsymbol

Return the DPOJET:MEAS<x>:BUSState:FROMSymbol command.

Description
  • This command sets or queries the symbol from which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:FROMSymbol? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:FROMSymbol? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:FROMSymbol value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:FROMSymbol <string>
- DPOJET:MEAS<x>:BUSState:FROMSymbol?

measurefrom property 

measurefrom: DpojetMeasItemBusstateMeasurefrom

Return the DPOJET:MEAS<x>:BUSState:MEASUREFrom command.

Description
  • This command sets or queries where the bus is measured from.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:MEASUREFrom? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREFrom? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREFrom value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:MEASUREFrom {CLOCKEdge|START|STOP}
- DPOJET:MEAS<x>:BUSState:MEASUREFrom?

measureto property 

measureto: DpojetMeasItemBusstateMeasureto

Return the DPOJET:MEAS<x>:BUSState:MEASURETO command.

Description
  • This command sets or queries from where the bus is measured to.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:MEASURETO? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:MEASURETO? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:MEASURETO value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:MEASURETO {START|STOP|CLOCKEdge}
- DPOJET:MEAS<x>:BUSState:MEASURETO?

measuretype property 

measuretype: DpojetMeasItemBusstateMeasuretype

Return the DPOJET:MEAS<x>:BUSState:MEASUREType command.

Description
  • This command sets or queries the type for which the bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:MEASUREType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:MEASUREType {SYMbol|PATTern}
- DPOJET:MEAS<x>:BUSState:MEASUREType?

topattern property 

topattern: DpojetMeasItemBusstateTopattern

Return the DPOJET:MEAS<x>:BUSState:TOPattern command.

Description
  • This command sets or queries the Pattern to which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:TOPattern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:TOPattern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:TOPattern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:TOPattern <string>
- DPOJET:MEAS<x>:BUSState:TOPattern?

tosymbol property 

tosymbol: DpojetMeasItemBusstateTosymbol

Return the DPOJET:MEAS<x>:BUSState:TOSymbol command.

Description
  • This command sets or queries the symbol to which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:TOSymbol? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:TOSymbol? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:TOSymbol value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:TOSymbol <string>
- DPOJET:MEAS<x>:BUSState:TOSymbol?

DpojetMeasItemBusstateClockpolarity

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:CLOCKPolarity command.

Description
  • This command sets or queries the clock polarity for the clock edge.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:CLOCKPolarity? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:CLOCKPolarity? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:CLOCKPolarity value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:CLOCKPolarity {RISING|FALLING}
- DPOJET:MEAS<x>:BUSState:CLOCKPolarity?

DpojetMeasItemBusstateFrompattern

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:FROMPattern command.

Description
  • This command sets or queries the Pattern from which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:FROMPattern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:FROMPattern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:FROMPattern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:FROMPattern <string>
- DPOJET:MEAS<x>:BUSState:FROMPattern?

DpojetMeasItemBusstateFromsymbol

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:FROMSymbol command.

Description
  • This command sets or queries the symbol from which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:FROMSymbol? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:FROMSymbol? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:FROMSymbol value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:FROMSymbol <string>
- DPOJET:MEAS<x>:BUSState:FROMSymbol?

DpojetMeasItemBusstateMeasurefrom

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:MEASUREFrom command.

Description
  • This command sets or queries where the bus is measured from.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:MEASUREFrom? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREFrom? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREFrom value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:MEASUREFrom {CLOCKEdge|START|STOP}
- DPOJET:MEAS<x>:BUSState:MEASUREFrom?

DpojetMeasItemBusstateMeasureto

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:MEASURETO command.

Description
  • This command sets or queries from where the bus is measured to.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:MEASURETO? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:MEASURETO? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:MEASURETO value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:MEASURETO {START|STOP|CLOCKEdge}
- DPOJET:MEAS<x>:BUSState:MEASURETO?

DpojetMeasItemBusstateMeasuretype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:MEASUREType command.

Description
  • This command sets or queries the type for which the bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:MEASUREType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:MEASUREType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:MEASUREType {SYMbol|PATTern}
- DPOJET:MEAS<x>:BUSState:MEASUREType?

DpojetMeasItemBusstateTopattern

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:TOPattern command.

Description
  • This command sets or queries the Pattern to which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:TOPattern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:TOPattern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:TOPattern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:TOPattern <string>
- DPOJET:MEAS<x>:BUSState:TOPattern?

DpojetMeasItemBusstateTosymbol

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:BUSState:TOSymbol command.

Description
  • This command sets or queries the symbol to which the Bus state is configured.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:BUSState:TOSymbol? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:BUSState:TOSymbol? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:BUSState:TOSymbol value command.
SCPI Syntax 
- DPOJET:MEAS<x>:BUSState:TOSymbol <string>
- DPOJET:MEAS<x>:BUSState:TOSymbol?

DpojetMeasItemClockrecovery

Bases: SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery? query and raise an AssertionError if the returned value does not match value.
Properties
  • .bhvrstandard: The DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard command.
  • .bwtype: The DPOJET:MEAS<x>:CLOCKRecovery:BWType command.
  • .clockbitrate: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate command.
  • .clockfrequency: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.
  • .clockmultiplier: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.
  • .clockpath: The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath command.
  • .damping: The DPOJET:MEAS<x>:CLOCKRecovery:DAMPing command.
  • .datarate: The DPOJET:MEAS<x>:CLOCKRecovery:DATARate command.
  • .loopbandwidth: The DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.
  • .meanautocalculate: The DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.
  • .method: The DPOJET:MEAS<x>:CLOCKRecovery:METHod command.
  • .model: The DPOJET:MEAS<x>:CLOCKRecovery:MODel command.
  • .nominaloffset: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.
  • .pattern: The DPOJET:MEAS<x>:CLOCKRecovery:PATTern command.
  • .standard: The DPOJET:MEAS<x>:CLOCKRecovery:STAndard command.

bhvrstandard property 

bhvrstandard: DpojetMeasItemClockrecoveryBhvrstandard

Return the DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard command.

Description
  • This command sets or queries the current behavioral standard, as specified in the user interface.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard <string>
- DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard?

bwtype property 

bwtype: DpojetMeasItemClockrecoveryBwtype

Return the DPOJET:MEAS<x>:CLOCKRecovery:BWType command.

Description
  • This command sets or queries the clock recovery bandwidth type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:BWType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BWType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BWType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:BWType {LOOPBW|JTFBW}
- DPOJET:MEAS<x>:CLOCKRecovery:BWType?

clockbitrate property 

clockbitrate: DpojetMeasItemClockrecoveryClockbitrate

Return the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate command.

Description
  • This command sets or queries the clock bit rate. Used if DATARate is 1.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate?

clockfrequency property 

clockfrequency: DpojetMeasItemClockrecoveryClockfrequency

Return the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.

Description
  • This command sets or queries the clock frequency. Used with Constant Clock - Fixed clock recovery method.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency?

clockmultiplier property 

clockmultiplier: DpojetMeasItemClockrecoveryClockmultiplier

Return the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.

Description
  • This command sets or queries the clock multiplier.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?

clockpath property 

clockpath: DpojetMeasItemClockrecoveryClockpath

Return the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath command.

Description
  • This command sets or queries the current known clock pattern path.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath <string>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath?

damping property 

damping: DpojetMeasItemClockrecoveryDamping

Return the DPOJET:MEAS<x>:CLOCKRecovery:DAMPing command.

Description
  • This command sets or queries the clock recovery damping value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:DAMPing? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DAMPing? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DAMPing value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:DAMPing?

datarate property 

datarate: DpojetMeasItemClockrecoveryDatarate

Return the DPOJET:MEAS<x>:CLOCKRecovery:DATARate command.

Description
  • This command turns on or off DATArate usage.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:DATARate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DATARate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DATARate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:DATARate {1|0}
- DPOJET:MEAS<x>:CLOCKRecovery:DATARate?

loopbandwidth property 

loopbandwidth: DpojetMeasItemClockrecoveryLoopbandwidth

Return the DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.

Description
  • This command sets or queries the clock recovery loop bandwidth.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth?

meanautocalculate property 

meanautocalculate: DpojetMeasItemClockrecoveryMeanautocalculate

Return the DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.

Description
  • This command sets or queries how often the clock is calculated, either FIRST, or on EVERY acquisition.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?

method property 

method: DpojetMeasItemClockrecoveryMethod

Return the DPOJET:MEAS<x>:CLOCKRecovery:METHod command.

Description
  • This command sets or queries the current Clock recovery method.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:METHod? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:METHod? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:METHod value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:METHod {STANDARD|CUSTOM|CONSTMEAN|CONSTFIXED|EXPEDGE|EXPPLL|CONSTMEDIAN|BEHAVIORAL}
- DPOJET:MEAS<x>:CLOCKRecovery:METHod?

model property 

model: DpojetMeasItemClockrecoveryModel

Return the DPOJET:MEAS<x>:CLOCKRecovery:MODel command.

Description
  • This command sets or queries the current clock recovery model.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:MODel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MODel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MODel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:MODel {ONE|TWO}
- DPOJET:MEAS<x>:CLOCKRecovery:MODel?

nominaloffset property 

nominaloffset: DpojetMeasItemClockrecoveryNominaloffset

Return the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.

Description
  • This command sets or queries the clock offset.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset?
Sub-properties
  • .auto: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO command.
  • .manual: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual command.
  • .recalctype: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype command.
  • .selectiontype: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

pattern property 

pattern: DpojetMeasItemClockrecoveryPattern

Return the DPOJET:MEAS<x>:CLOCKRecovery:PATTern command.

Description
  • This command turns on or off the usage of CLOCKPath to a specific known data pattern.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:PATTern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:PATTern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:PATTern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:PATTern {1|0}
- DPOJET:MEAS<x>:CLOCKRecovery:PATTern?

standard property 

standard: DpojetMeasItemClockrecoveryStandard

Return the DPOJET:MEAS<x>:CLOCKRecovery:STAndard command.

Description
  • This command sets or queries the current clock recovery standard, as specified in the user interface.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:STAndard? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:STAndard? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:STAndard value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:STAndard <string>
- DPOJET:MEAS<x>:CLOCKRecovery:STAndard?

DpojetMeasItemClockrecoveryBhvrstandard

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard command.

Description
  • This command sets or queries the current behavioral standard, as specified in the user interface.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard <string>
- DPOJET:MEAS<x>:CLOCKRecovery:BHVRSTANdard?

DpojetMeasItemClockrecoveryBwtype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:BWType command.

Description
  • This command sets or queries the clock recovery bandwidth type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:BWType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BWType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:BWType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:BWType {LOOPBW|JTFBW}
- DPOJET:MEAS<x>:CLOCKRecovery:BWType?

DpojetMeasItemClockrecoveryClockbitrate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate command.

Description
  • This command sets or queries the clock bit rate. Used if DATARate is 1.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKBitrate?

DpojetMeasItemClockrecoveryClockfrequency

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency command.

Description
  • This command sets or queries the clock frequency. Used with Constant Clock - Fixed clock recovery method.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKFrequency?

DpojetMeasItemClockrecoveryClockmultiplier

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier command.

Description
  • This command sets or queries the clock multiplier.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKMultiplier?

DpojetMeasItemClockrecoveryClockpath

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath command.

Description
  • This command sets or queries the current known clock pattern path.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath <string>
- DPOJET:MEAS<x>:CLOCKRecovery:CLOCKPath?

DpojetMeasItemClockrecoveryDamping

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:DAMPing command.

Description
  • This command sets or queries the clock recovery damping value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:DAMPing? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DAMPing? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DAMPing value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:DAMPing <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:DAMPing?

DpojetMeasItemClockrecoveryDatarate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:DATARate command.

Description
  • This command turns on or off DATArate usage.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:DATARate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DATARate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:DATARate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:DATARate {1|0}
- DPOJET:MEAS<x>:CLOCKRecovery:DATARate?

DpojetMeasItemClockrecoveryLoopbandwidth

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth command.

Description
  • This command sets or queries the clock recovery loop bandwidth.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:LOOPBandwidth?

DpojetMeasItemClockrecoveryMeanautocalculate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate command.

Description
  • This command sets or queries how often the clock is calculated, either FIRST, or on EVERY acquisition.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate {FIRST|EVERY}
- DPOJET:MEAS<x>:CLOCKRecovery:MEANAUTOCalculate?

DpojetMeasItemClockrecoveryMethod

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:METHod command.

Description
  • This command sets or queries the current Clock recovery method.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:METHod? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:METHod? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:METHod value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:METHod {STANDARD|CUSTOM|CONSTMEAN|CONSTFIXED|EXPEDGE|EXPPLL|CONSTMEDIAN|BEHAVIORAL}
- DPOJET:MEAS<x>:CLOCKRecovery:METHod?

DpojetMeasItemClockrecoveryModel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:MODel command.

Description
  • This command sets or queries the current clock recovery model.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:MODel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MODel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:MODel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:MODel {ONE|TWO}
- DPOJET:MEAS<x>:CLOCKRecovery:MODel?

DpojetMeasItemClockrecoveryNominaloffset

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset command.

Description
  • This command sets or queries the clock offset.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset?
Properties
  • .auto: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO command.
  • .manual: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual command.
  • .recalctype: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype command.
  • .selectiontype: The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

auto property 

auto: DpojetMeasItemClockrecoveryNominaloffsetAuto

Return the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO command.

Description
  • This query-only command returns the value in the Auto text box for the Nominal Clock Offset controls. If the nominal clock offset method selection type is set to Auto and an acquisition cycle has been completed, this field shows the clock-to-data offset that was automatically determined. A positive value means that the clock leads the data (precedes it in time). If the offset has not been determined, the returned string is TBD.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO?

manual property 

manual: DpojetMeasItemClockrecoveryNominaloffsetManual

Return the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual command.

Description
  • This command sets or queries the value for Manual text box.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual?

recalctype property 

recalctype: DpojetMeasItemClockrecoveryNominaloffsetRecalctype

Return the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype command.

Description
  • This command sets or queries the recalculation list box.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype {FIRST|EVERY}
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype?

selectiontype property 

selectiontype: DpojetMeasItemClockrecoveryNominaloffsetSelectiontype

Return the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

Description
  • This command sets or queries the selection type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?

DpojetMeasItemClockrecoveryNominaloffsetAuto

Bases: SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO command.

Description
  • This query-only command returns the value in the Auto text box for the Nominal Clock Offset controls. If the nominal clock offset method selection type is set to Auto and an acquisition cycle has been completed, this field shows the clock-to-data offset that was automatically determined. A positive value means that the clock leads the data (precedes it in time). If the offset has not been determined, the returned string is TBD.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:AUTO?

DpojetMeasItemClockrecoveryNominaloffsetManual

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual command.

Description
  • This command sets or queries the value for Manual text box.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual <NR3>
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:MANual?

DpojetMeasItemClockrecoveryNominaloffsetRecalctype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype command.

Description
  • This command sets or queries the recalculation list box.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype {FIRST|EVERY}
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:Recalctype?

DpojetMeasItemClockrecoveryNominaloffsetSelectiontype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype command.

Description
  • This command sets or queries the selection type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype {AUTO|MANUAL}
- DPOJET:MEAS<x>:CLOCKRecovery:NOMINALOFFset:SELECTIONtype?

DpojetMeasItemClockrecoveryPattern

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:PATTern command.

Description
  • This command turns on or off the usage of CLOCKPath to a specific known data pattern.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:PATTern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:PATTern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:PATTern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:PATTern {1|0}
- DPOJET:MEAS<x>:CLOCKRecovery:PATTern?

DpojetMeasItemClockrecoveryStandard

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CLOCKRecovery:STAndard command.

Description
  • This command sets or queries the current clock recovery standard, as specified in the user interface.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CLOCKRecovery:STAndard? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:STAndard? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CLOCKRecovery:STAndard value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CLOCKRecovery:STAndard <string>
- DPOJET:MEAS<x>:CLOCKRecovery:STAndard?

DpojetMeasItemCommonmode

Bases: SCPICmdRead

The DPOJET:MEAS<x>:COMMONMode command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:COMMONMode? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:COMMONMode? query and raise an AssertionError if the returned value does not match value.
Properties
  • .filters: The DPOJET:MEAS<x>:COMMONMode:FILTers command tree.

filters property 

filters: DpojetMeasItemCommonmodeFilters

Return the DPOJET:MEAS<x>:COMMONMode:FILTers command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:COMMONMode:FILTers? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:COMMONMode:FILTers? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .state: The DPOJET:MEAS<x>:COMMONMode:FILTers:STATE command.

DpojetMeasItemCommonmodeFilters

Bases: SCPICmdRead

The DPOJET:MEAS<x>:COMMONMode:FILTers command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:COMMONMode:FILTers? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:COMMONMode:FILTers? query and raise an AssertionError if the returned value does not match value.
Properties
  • .state: The DPOJET:MEAS<x>:COMMONMode:FILTers:STATE command.

state property 

state: DpojetMeasItemCommonmodeFiltersState

Return the DPOJET:MEAS<x>:COMMONMode:FILTers:STATE command.

Description
  • This command sets or queries the state of the common mode filter frequency.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:COMMONMode:FILTers:STATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:COMMONMode:FILTers:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:COMMONMode:FILTers:STATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF}
- DPOJET:MEAS<x>:COMMONMode:FILTers:STATE?

DpojetMeasItemCommonmodeFiltersState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:COMMONMode:FILTers:STATE command.

Description
  • This command sets or queries the state of the common mode filter frequency.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:COMMONMode:FILTers:STATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:COMMONMode:FILTers:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:COMMONMode:FILTers:STATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:COMMONMode:FILTers:STATE {ON|OFF}
- DPOJET:MEAS<x>:COMMONMode:FILTers:STATE?

DpojetMeasItemCustomgating

Bases: SCPICmdRead

The DPOJET:MEAS<x>:CUSTOMGATING command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING? query and raise an AssertionError if the returned value does not match value.
Properties
  • .fromedge: The DPOJET:MEAS<x>:CUSTOMGATING:FROMedge command.
  • .measurementedge: The DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge command.
  • .source1gate: The DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE command.
  • .source2gate: The DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE command.
  • .toedge: The DPOJET:MEAS<x>:CUSTOMGATING:TOedge command.

fromedge property 

fromedge: DpojetMeasItemCustomgatingFromedge

Return the DPOJET:MEAS<x>:CUSTOMGATING:FROMedge command.

Description
  • This commands sets or queries the edge type for source1.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:FROMedge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:FROMedge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:FROMedge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:FROMedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:CUSTOMGATING:FROMedge?

measurementedge property 

measurementedge: DpojetMeasItemCustomgatingMeasurementedge

Return the DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge command.

Description
  • This command sets or queries the current measurement edge.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge {FIRST|ALL}
- DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge?

source1gate property 

source1gate: DpojetMeasItemCustomgatingSource1gate

Return the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE command.

Description
  • This commands sets or queries the gate associated with source1.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE {GATE1|GATE2|GATE3 GATE4|GATE5|GATE6|GATE7|GATE8|GATE9|GATE10|GATE11|GATE12|GATE13|GATE14|GATE15|GATE16|NONE}
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE?

source2gate property 

source2gate: DpojetMeasItemCustomgatingSource2gate

Return the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE command.

Description
  • This commands sets or queries the gate associated with source2.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE {GATE1|GATE2|GATE3 GATE4|GATE5|GATE6|GATE7|GATE8|GATE9|GATE10|GATE11|GATE12|GATE13|GATE14|GATE15|GATE16|NONE }
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE?

toedge property 

toedge: DpojetMeasItemCustomgatingToedge

Return the DPOJET:MEAS<x>:CUSTOMGATING:TOedge command.

Description
  • This commands sets or queries the edge type for source2.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:TOedge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:TOedge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:TOedge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:TOedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:CUSTOMGATING:TOedge?

DpojetMeasItemCustomgatingFromedge

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CUSTOMGATING:FROMedge command.

Description
  • This commands sets or queries the edge type for source1.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:FROMedge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:FROMedge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:FROMedge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:FROMedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:CUSTOMGATING:FROMedge?

DpojetMeasItemCustomgatingMeasurementedge

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge command.

Description
  • This command sets or queries the current measurement edge.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge {FIRST|ALL}
- DPOJET:MEAS<x>:CUSTOMGATING:MEASUREMENTEdge?

DpojetMeasItemCustomgatingSource1gate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE command.

Description
  • This commands sets or queries the gate associated with source1.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE {GATE1|GATE2|GATE3 GATE4|GATE5|GATE6|GATE7|GATE8|GATE9|GATE10|GATE11|GATE12|GATE13|GATE14|GATE15|GATE16|NONE}
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE1GATE?

DpojetMeasItemCustomgatingSource2gate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE command.

Description
  • This commands sets or queries the gate associated with source2.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE {GATE1|GATE2|GATE3 GATE4|GATE5|GATE6|GATE7|GATE8|GATE9|GATE10|GATE11|GATE12|GATE13|GATE14|GATE15|GATE16|NONE }
- DPOJET:MEAS<x>:CUSTOMGATING:SOURCE2GATE?

DpojetMeasItemCustomgatingToedge

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CUSTOMGATING:TOedge command.

Description
  • This commands sets or queries the edge type for source2.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTOMGATING:TOedge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:TOedge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTOMGATING:TOedge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTOMGATING:TOedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:CUSTOMGATING:TOedge?

DpojetMeasItemCustomname

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:CUSTomname command.

Description
  • This command sets or queries the custom measurement name for the measurement in slot x.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:CUSTomname? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:CUSTomname? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:CUSTomname value command.
SCPI Syntax 
- DPOJET:MEAS<x>:CUSTomname <string>
- DPOJET:MEAS<x>:CUSTomname?

DpojetMeasItemData

Bases: SCPICmdRead

The DPOJET:MEAS<x>:DATA command.

Description
  • This query-only command returns the measurement data. This is similar to the curve query, where the output is in the format #, where is the number of bytes. For Example: If =500, =3 is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DATA? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DATA? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:DATA?

DpojetMeasItemDfe

Bases: SCPICmdRead

The DPOJET:MEAS<x>:DFE command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE? query and raise an AssertionError if the returned value does not match value.
Properties
  • .absolutetimestate: The DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState command.
  • .absolutetimevalue: The DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue command.
  • .absolutevoltagestate: The DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState command.
  • .absolutevoltagevalue: The DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue command.
  • .delaycompensation: The DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION command.
  • .manualdelay: The DPOJET:MEAS<x>:DFE:MANUALDELAY command.
  • .measatpercent: The DPOJET:MEAS<x>:DFE:MEASatpercent command.
  • .resolution: The DPOJET:MEAS<x>:DFE:RESOlution command.
  • .tapstate: The DPOJET:MEAS<x>:DFE:TAPState command.
  • .tapvalue: The DPOJET:MEAS<x>:DFE:TAPValue command.

absolutetimestate property 

absolutetimestate: DpojetMeasItemDfeAbsolutetimestate

Return the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState command.

Description
  • This command sets or queries DFE absolute time state for DFE_EyeHeight measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState {ON|OFF|1|0}
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState?

absolutetimevalue property 

absolutetimevalue: DpojetMeasItemDfeAbsolutetimevalue

Return the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue command.

Description
  • This command sets or queries DFE absolute time value for DFE_EyeHeight measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue <NR3>
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue?

absolutevoltagestate property 

absolutevoltagestate: DpojetMeasItemDfeAbsolutevoltagestate

Return the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState command.

Description
  • This command sets or queries DFE absolute voltage state for DFE_EyeWidth measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState {ON|OFF|1|0}
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState?

absolutevoltagevalue property 

absolutevoltagevalue: DpojetMeasItemDfeAbsolutevoltagevalue

Return the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue command.

Description
  • This command sets or queries DFE absolute voltage value for DFE_EyeWidth measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue <NR3>
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue?

delaycompensation property 

delaycompensation: DpojetMeasItemDfeDelaycompensation

Return the DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION command.

Description
  • This command sets or queries the DFE delay compensation.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION {MANUAL,AUTO}
- DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION?

manualdelay property 

manualdelay: DpojetMeasItemDfeManualdelay

Return the DPOJET:MEAS<x>:DFE:MANUALDELAY command.

Description
  • This command sets or queries the manual delay value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:MANUALDELAY? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:MANUALDELAY? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:MANUALDELAY value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:MANUALDELAY <NR3>
- DPOJET:MEAS<x>:DFE:MANUALDELAY?

measatpercent property 

measatpercent: DpojetMeasItemDfeMeasatpercent

Return the DPOJET:MEAS<x>:DFE:MEASatpercent command.

Description
  • This command sets or queries the measure at X% value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:MEASatpercent? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:MEASatpercent? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:MEASatpercent value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:MEASatpercent <NR3>
- DPOJET:MEAS<x>:DFE:MEASatpercent?

resolution property 

resolution: DpojetMeasItemDfeResolution

Return the DPOJET:MEAS<x>:DFE:RESOlution command.

Description
  • This command sets or queries the resolution.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:RESOlution? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:RESOlution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:RESOlution value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:RESOlution <NR3>
- DPOJET:MEAS<x>:DFE:RESOlution?

tapstate property 

tapstate: DpojetMeasItemDfeTapstate

Return the DPOJET:MEAS<x>:DFE:TAPState command.

Description
  • This command sets or queries the tap value state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:TAPState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:TAPState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:TAPState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:TAPState {0|1}
- DPOJET:MEAS<x>:DFE:TAPState?

tapvalue property 

tapvalue: DpojetMeasItemDfeTapvalue

Return the DPOJET:MEAS<x>:DFE:TAPValue command.

Description
  • This command sets or queries the tap value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:TAPValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:TAPValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:TAPValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:TAPValue <NR3>
- DPOJET:MEAS<x>:DFE:TAPValue?

DpojetMeasItemDfeAbsolutetimestate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState command.

Description
  • This command sets or queries DFE absolute time state for DFE_EyeHeight measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState {ON|OFF|1|0}
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEState?

DpojetMeasItemDfeAbsolutetimevalue

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue command.

Description
  • This command sets or queries DFE absolute time value for DFE_EyeHeight measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue <NR3>
- DPOJET:MEAS<x>:DFE:ABSOLUTETIMEValue?

DpojetMeasItemDfeAbsolutevoltagestate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState command.

Description
  • This command sets or queries DFE absolute voltage state for DFE_EyeWidth measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState {ON|OFF|1|0}
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEState?

DpojetMeasItemDfeAbsolutevoltagevalue

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue command.

Description
  • This command sets or queries DFE absolute voltage value for DFE_EyeWidth measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue <NR3>
- DPOJET:MEAS<x>:DFE:ABSOLUTEVOLTAGEValue?

DpojetMeasItemDfeDelaycompensation

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION command.

Description
  • This command sets or queries the DFE delay compensation.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION {MANUAL,AUTO}
- DPOJET:MEAS<x>:DFE:DELAYCOMPENSATION?

DpojetMeasItemDfeManualdelay

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:MANUALDELAY command.

Description
  • This command sets or queries the manual delay value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:MANUALDELAY? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:MANUALDELAY? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:MANUALDELAY value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:MANUALDELAY <NR3>
- DPOJET:MEAS<x>:DFE:MANUALDELAY?

DpojetMeasItemDfeMeasatpercent

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:MEASatpercent command.

Description
  • This command sets or queries the measure at X% value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:MEASatpercent? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:MEASatpercent? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:MEASatpercent value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:MEASatpercent <NR3>
- DPOJET:MEAS<x>:DFE:MEASatpercent?

DpojetMeasItemDfeResolution

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:RESOlution command.

Description
  • This command sets or queries the resolution.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:RESOlution? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:RESOlution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:RESOlution value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:RESOlution <NR3>
- DPOJET:MEAS<x>:DFE:RESOlution?

DpojetMeasItemDfeTapstate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:TAPState command.

Description
  • This command sets or queries the tap value state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:TAPState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:TAPState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:TAPState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:TAPState {0|1}
- DPOJET:MEAS<x>:DFE:TAPState?

DpojetMeasItemDfeTapvalue

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:DFE:TAPValue command.

Description
  • This command sets or queries the tap value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DFE:TAPValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DFE:TAPValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:DFE:TAPValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:DFE:TAPValue <NR3>
- DPOJET:MEAS<x>:DFE:TAPValue?

DpojetMeasItemDisplayname

Bases: SCPICmdRead

The DPOJET:MEAS<x>:DISPLAYNAME command.

Description
  • This command queries the UI name of the measurement x in the measurement table. Note: If the measurement UI name has special character δ, then it is displayed as d.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:DISPLAYNAME? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:DISPLAYNAME? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:DISPLAYNAME?

DpojetMeasItemEdge1

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGE1 command.

Description
  • This command sets or queries the Source1 edge type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGE1? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGE1? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGE1 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGE1 {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:EDGE1?

DpojetMeasItemEdge2

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGE2 command.

Description
  • This command sets or queries the Source2 edge type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGE2? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGE2? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGE2 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGE2 {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:EDGE2?

DpojetMeasItemEdgeincre

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGEIncre command.

Description
  • This command sets or queries the measurement edge increment value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGEIncre? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGEIncre? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGEIncre value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGEIncre <NR3>
- DPOJET:MEAS<x>:EDGEIncre?

DpojetMeasItemEdges

Bases: SCPICmdRead

The DPOJET:MEAS<x>:EDGES command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES? query and raise an AssertionError if the returned value does not match value.
Properties
  • .eyeheightstate: The DPOJET:MEAS<x>:EDGES:EYEHeightstate command.
  • .fromlevel: The DPOJET:MEAS<x>:EDGES:FROMLevel command.
  • .level: The DPOJET:MEAS<x>:EDGES:LEVel command.
  • .slewratetechnique: The DPOJET:MEAS<x>:EDGES:SLEWRATETechnique command.
  • .subratedivisor: The DPOJET:MEAS<x>:EDGES:SUBRATEDivisor command.
  • .tolevel: The DPOJET:MEAS<x>:EDGES:TOLevel command.
  • .userdefinedvoltage: The DPOJET:MEAS<x>:EDGES:USERDefinedvoltage command.
  • .voltagestate: The DPOJET:MEAS<x>:EDGES:VOLTAGEState command.

eyeheightstate property 

eyeheightstate: DpojetMeasItemEdgesEyeheightstate

Return the DPOJET:MEAS<x>:EDGES:EYEHeightstate command.

Description
  • This command sets or queries the automated eye height state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:EYEHeightstate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:EYEHeightstate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:EYEHeightstate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:EYEHeightstate {1|0}
- DPOJET:MEAS<x>:EDGES:EYEHeightstate?

fromlevel property 

fromlevel: DpojetMeasItemEdgesFromlevel

Return the DPOJET:MEAS<x>:EDGES:FROMLevel command.

Description
  • This command sets or queries the FromLevel edge for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:FROMLevel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:FROMLevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:FROMLevel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:FROMLevel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:FROMLevel?

level property 

level: DpojetMeasItemEdgesLevel

Return the DPOJET:MEAS<x>:EDGES:LEVel command.

Description
  • This command sets or queries the level used for the edges configuration.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:LEVel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:LEVel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:LEVel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:LEVel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:LEVel?

slewratetechnique property 

slewratetechnique: DpojetMeasItemEdgesSlewratetechnique

Return the DPOJET:MEAS<x>:EDGES:SLEWRATETechnique command.

Description
  • This command sets or queries the slew rate technique for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:SLEWRATETechnique? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:SLEWRATETechnique? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:SLEWRATETechnique value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:SLEWRATETechnique {NOMinalmethod|DDRmethod}
- DPOJET:MEAS<x>:EDGES:SLEWRATETechnique?

subratedivisor property 

subratedivisor: DpojetMeasItemEdgesSubratedivisor

Return the DPOJET:MEAS<x>:EDGES:SUBRATEDivisor command.

Description
  • This command sets or queries the subrate divisor value for the application measurement slot with index .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:SUBRATEDivisor? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:SUBRATEDivisor? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:SUBRATEDivisor value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:SUBRATEDivisor {TWO|FOUR|EIGHT}
- DPOJET:MEAS<x>:EDGES:SUBRATEDivisor?

tolevel property 

tolevel: DpojetMeasItemEdgesTolevel

Return the DPOJET:MEAS<x>:EDGES:TOLevel command.

Description
  • This command sets or queries the ToLevel edge for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:TOLevel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:TOLevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:TOLevel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:TOLevel?

userdefinedvoltage property 

userdefinedvoltage: DpojetMeasItemEdgesUserdefinedvoltage

Return the DPOJET:MEAS<x>:EDGES:USERDefinedvoltage command.

Description
  • This command sets or queries the user defined voltage.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:USERDefinedvoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:USERDefinedvoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:USERDefinedvoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:USERDefinedvoltage <NR3>
- DPOJET:MEAS<x>:EDGES:USERDefinedvoltage?

voltagestate property 

voltagestate: DpojetMeasItemEdgesVoltagestate

Return the DPOJET:MEAS<x>:EDGES:VOLTAGEState command.

Description
  • This command sets or queries the user defined voltage state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:VOLTAGEState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:VOLTAGEState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:VOLTAGEState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:VOLTAGEState {1|0}
- DPOJET:MEAS<x>:EDGES:VOLTAGEState?

DpojetMeasItemEdgesEyeheightstate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:EYEHeightstate command.

Description
  • This command sets or queries the automated eye height state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:EYEHeightstate? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:EYEHeightstate? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:EYEHeightstate value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:EYEHeightstate {1|0}
- DPOJET:MEAS<x>:EDGES:EYEHeightstate?

DpojetMeasItemEdgesFromlevel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:FROMLevel command.

Description
  • This command sets or queries the FromLevel edge for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:FROMLevel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:FROMLevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:FROMLevel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:FROMLevel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:FROMLevel?

DpojetMeasItemEdgesLevel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:LEVel command.

Description
  • This command sets or queries the level used for the edges configuration.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:LEVel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:LEVel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:LEVel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:LEVel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:LEVel?

DpojetMeasItemEdgesSlewratetechnique

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:SLEWRATETechnique command.

Description
  • This command sets or queries the slew rate technique for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:SLEWRATETechnique? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:SLEWRATETechnique? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:SLEWRATETechnique value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:SLEWRATETechnique {NOMinalmethod|DDRmethod}
- DPOJET:MEAS<x>:EDGES:SLEWRATETechnique?

DpojetMeasItemEdgesSubratedivisor

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:SUBRATEDivisor command.

Description
  • This command sets or queries the subrate divisor value for the application measurement slot with index .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:SUBRATEDivisor? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:SUBRATEDivisor? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:SUBRATEDivisor value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:SUBRATEDivisor {TWO|FOUR|EIGHT}
- DPOJET:MEAS<x>:EDGES:SUBRATEDivisor?

DpojetMeasItemEdgesTolevel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:TOLevel command.

Description
  • This command sets or queries the ToLevel edge for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:TOLevel? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:TOLevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:TOLevel value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:TOLevel {HIGH|MID|LOW}
- DPOJET:MEAS<x>:EDGES:TOLevel?

DpojetMeasItemEdgesUserdefinedvoltage

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:USERDefinedvoltage command.

Description
  • This command sets or queries the user defined voltage.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:USERDefinedvoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:USERDefinedvoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:USERDefinedvoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:USERDefinedvoltage <NR3>
- DPOJET:MEAS<x>:EDGES:USERDefinedvoltage?

DpojetMeasItemEdgesVoltagestate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:EDGES:VOLTAGEState command.

Description
  • This command sets or queries the user defined voltage state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:EDGES:VOLTAGEState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:EDGES:VOLTAGEState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:EDGES:VOLTAGEState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:EDGES:VOLTAGEState {1|0}
- DPOJET:MEAS<x>:EDGES:VOLTAGEState?

DpojetMeasItemFilters

Bases: SCPICmdRead

The DPOJET:MEAS<x>:FILTers command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers? query and raise an AssertionError if the returned value does not match value.
Properties
  • .blankingtime: The DPOJET:MEAS<x>:FILTers:BLANKingtime command.
  • .highpass: The DPOJET:MEAS<x>:FILTers:HIGHPass command tree.
  • .lowpass: The DPOJET:MEAS<x>:FILTers:LOWPass command tree.
  • .ramptime: The DPOJET:MEAS<x>:FILTers:RAMPtime command.
  • .sjbandwidth: The DPOJET:MEAS<x>:FILTers:SJBAndwidth command.
  • .sjfrequency: The DPOJET:MEAS<x>:FILTers:SJFRequency command.

blankingtime property 

blankingtime: DpojetMeasItemFiltersBlankingtime

Return the DPOJET:MEAS<x>:FILTers:BLANKingtime command.

Description
  • This command sets or queries the current filter blanking time.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:BLANKingtime? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:BLANKingtime? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:BLANKingtime value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:BLANKingtime <NR3>
- DPOJET:MEAS<x>:FILTers:BLANKingtime?

highpass property 

highpass: DpojetMeasItemFiltersHighpass

Return the DPOJET:MEAS<x>:FILTers:HIGHPass command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:HIGHPass? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .freq: The DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ command.
  • .spec: The DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC command.

lowpass property 

lowpass: DpojetMeasItemFiltersLowpass

Return the DPOJET:MEAS<x>:FILTers:LOWPass command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:LOWPass? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .freq: The DPOJET:MEAS<x>:FILTers:LOWPass:FREQ command.
  • .spec: The DPOJET:MEAS<x>:FILTers:LOWPass:SPEC command.

ramptime property 

ramptime: DpojetMeasItemFiltersRamptime

Return the DPOJET:MEAS<x>:FILTers:RAMPtime command.

Description
  • This command sets or queries the current filter ramp time.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:RAMPtime? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:RAMPtime? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:RAMPtime value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:RAMPtime <NR3>
- DPOJET:MEAS<x>:FILTers:RAMPtime?

sjbandwidth property 

sjbandwidth: DpojetMeasItemFiltersSjbandwidth

Return the DPOJET:MEAS<x>:FILTers:SJBAndwidth command.

Description
  • This command sets or queries the SJ Bandwidth of SJ@FREQ measurement for the application measurement slot with index .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:SJBAndwidth? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:SJBAndwidth? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:SJBAndwidth value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:SJBAndwidth <NR3>
- DPOJET:MEAS<x>:FILTers:SJBAndwidth?

sjfrequency property 

sjfrequency: DpojetMeasItemFiltersSjfrequency

Return the DPOJET:MEAS<x>:FILTers:SJFRequency command.

Description
  • This command sets or queries the SJ Frequency of SJ@FREQ measurement for the application measurement slot with index .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:SJFRequency? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:SJFRequency? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:SJFRequency value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:SJFRequency <NR3>
- DPOJET:MEAS<x>:FILTers:SJFRequency?

DpojetMeasItemFiltersBlankingtime

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:BLANKingtime command.

Description
  • This command sets or queries the current filter blanking time.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:BLANKingtime? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:BLANKingtime? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:BLANKingtime value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:BLANKingtime <NR3>
- DPOJET:MEAS<x>:FILTers:BLANKingtime?

DpojetMeasItemFiltersHighpass

Bases: SCPICmdRead

The DPOJET:MEAS<x>:FILTers:HIGHPass command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:HIGHPass? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass? query and raise an AssertionError if the returned value does not match value.
Properties
  • .freq: The DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ command.
  • .spec: The DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC command.

freq property 

freq: DpojetMeasItemFiltersHighpassFreq

Return the DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ command.

Description
  • This command sets or queries the current high pass filter frequency.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ?

spec property 

spec: DpojetMeasItemFiltersHighpassSpec

Return the DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC command.

Description
  • This command sets or queries the current high pass filter specification.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC?

DpojetMeasItemFiltersHighpassFreq

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ command.

Description
  • This command sets or queries the current high pass filter frequency.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ <NR3>
- DPOJET:MEAS<x>:FILTers:HIGHPass:FREQ?

DpojetMeasItemFiltersHighpassSpec

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC command.

Description
  • This command sets or queries the current high pass filter specification.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC {NONE|FIRST|SECOND|THIRD}
- DPOJET:MEAS<x>:FILTers:HIGHPass:SPEC?

DpojetMeasItemFiltersLowpass

Bases: SCPICmdRead

The DPOJET:MEAS<x>:FILTers:LOWPass command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:LOWPass? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass? query and raise an AssertionError if the returned value does not match value.
Properties
  • .freq: The DPOJET:MEAS<x>:FILTers:LOWPass:FREQ command.
  • .spec: The DPOJET:MEAS<x>:FILTers:LOWPass:SPEC command.

freq property 

freq: DpojetMeasItemFiltersLowpassFreq

Return the DPOJET:MEAS<x>:FILTers:LOWPass:FREQ command.

Description
  • This command sets or queries the current low pass filter frequency.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:LOWPass:FREQ? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:FREQ value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- DPOJET:MEAS<x>:FILTers:LOWPass:FREQ?

spec property 

spec: DpojetMeasItemFiltersLowpassSpec

Return the DPOJET:MEAS<x>:FILTers:LOWPass:SPEC command.

Description
  • This command sets or queries the current low pass filter specification.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:LOWPass:SPEC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:SPEC value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- DPOJET:MEAS<x>:FILTers:LOWPass:SPEC?

DpojetMeasItemFiltersLowpassFreq

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:LOWPass:FREQ command.

Description
  • This command sets or queries the current low pass filter frequency.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:LOWPass:FREQ? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:FREQ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:FREQ value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:LOWPass:FREQ <NR3>
- DPOJET:MEAS<x>:FILTers:LOWPass:FREQ?

DpojetMeasItemFiltersLowpassSpec

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:LOWPass:SPEC command.

Description
  • This command sets or queries the current low pass filter specification.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:LOWPass:SPEC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:SPEC? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:LOWPass:SPEC value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:LOWPass:SPEC {NONE|FIRST|SECOND|THIRD}
- DPOJET:MEAS<x>:FILTers:LOWPass:SPEC?

DpojetMeasItemFiltersRamptime

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:RAMPtime command.

Description
  • This command sets or queries the current filter ramp time.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:RAMPtime? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:RAMPtime? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:RAMPtime value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:RAMPtime <NR3>
- DPOJET:MEAS<x>:FILTers:RAMPtime?

DpojetMeasItemFiltersSjbandwidth

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:SJBAndwidth command.

Description
  • This command sets or queries the SJ Bandwidth of SJ@FREQ measurement for the application measurement slot with index .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:SJBAndwidth? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:SJBAndwidth? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:SJBAndwidth value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:SJBAndwidth <NR3>
- DPOJET:MEAS<x>:FILTers:SJBAndwidth?

DpojetMeasItemFiltersSjfrequency

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FILTers:SJFRequency command.

Description
  • This command sets or queries the SJ Frequency of SJ@FREQ measurement for the application measurement slot with index .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FILTers:SJFRequency? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FILTers:SJFRequency? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FILTers:SJFRequency value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FILTers:SJFRequency <NR3>
- DPOJET:MEAS<x>:FILTers:SJFRequency?

DpojetMeasItemFromedge

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:FROMedge command.

Description
  • This command sets the FROMedge value for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:FROMedge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:FROMedge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:FROMedge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:FROMedge {RISe|FALL|BOTH}
- DPOJET:MEAS<x>:FROMedge?

DpojetMeasItemHighrefvoltage

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:HIGHREFVoltage command.

Description
  • This command sets or queries the high reference voltage value for the selected configuration.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:HIGHREFVoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:HIGHREFVoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:HIGHREFVoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:HIGHREFVoltage <NR3>
- DPOJET:MEAS<x>:HIGHREFVoltage?

DpojetMeasItemLogging

Bases: SCPICmdRead

The DPOJET:MEAS<x>:LOGging command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging? query and raise an AssertionError if the returned value does not match value.
Properties
  • .measurements: The DPOJET:MEAS<x>:LOGging:MEASurements command tree.
  • .statistics: The DPOJET:MEAS<x>:LOGging:STATistics command tree.
  • .worstcase: The DPOJET:MEAS<x>:LOGging:WORSTcase command tree.

measurements property 

measurements: DpojetMeasItemLoggingMeasurements

Return the DPOJET:MEAS<x>:LOGging:MEASurements command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:MEASurements? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .filename: The DPOJET:MEAS<x>:LOGging:MEASurements:FILEname command.
  • .select: The DPOJET:MEAS<x>:LOGging:MEASurements:SELect command.

statistics property 

statistics: DpojetMeasItemLoggingStatistics

Return the DPOJET:MEAS<x>:LOGging:STATistics command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:STATistics? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:STATistics? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .select: The DPOJET:MEAS<x>:LOGging:STATistics:SELect command.

worstcase property 

worstcase: DpojetMeasItemLoggingWorstcase

Return the DPOJET:MEAS<x>:LOGging:WORSTcase command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:WORSTcase? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:WORSTcase? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .select: The DPOJET:MEAS<x>:LOGging:WORSTcase:SELect command.

DpojetMeasItemLoggingMeasurements

Bases: SCPICmdRead

The DPOJET:MEAS<x>:LOGging:MEASurements command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:MEASurements? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements? query and raise an AssertionError if the returned value does not match value.
Properties
  • .filename: The DPOJET:MEAS<x>:LOGging:MEASurements:FILEname command.
  • .select: The DPOJET:MEAS<x>:LOGging:MEASurements:SELect command.

filename property 

filename: DpojetMeasItemLoggingMeasurementsFilename

Return the DPOJET:MEAS<x>:LOGging:MEASurements:FILEname command.

Description
  • This command queries the current file name that will be used for the measurement when measurement logging is turned on.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:MEASurements:FILEname? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements:FILEname? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:MEASurements:FILEname?

select property 

select: DpojetMeasItemLoggingMeasurementsSelect

Return the DPOJET:MEAS<x>:LOGging:MEASurements:SELect command.

Description
  • This command sets or queries the given measurement to be included in any measurement logging. Statistic logging is turned on or off as a whole, using the DPOJET:LOGging branch.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:MEASurements:SELect? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements:SELect? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements:SELect value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:MEASurements:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:MEASurements:SELect?

DpojetMeasItemLoggingMeasurementsFilename

Bases: SCPICmdRead

The DPOJET:MEAS<x>:LOGging:MEASurements:FILEname command.

Description
  • This command queries the current file name that will be used for the measurement when measurement logging is turned on.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:MEASurements:FILEname? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements:FILEname? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:MEASurements:FILEname?

DpojetMeasItemLoggingMeasurementsSelect

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:LOGging:MEASurements:SELect command.

Description
  • This command sets or queries the given measurement to be included in any measurement logging. Statistic logging is turned on or off as a whole, using the DPOJET:LOGging branch.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:MEASurements:SELect? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements:SELect? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOGging:MEASurements:SELect value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:MEASurements:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:MEASurements:SELect?

DpojetMeasItemLoggingStatistics

Bases: SCPICmdRead

The DPOJET:MEAS<x>:LOGging:STATistics command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:STATistics? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:STATistics? query and raise an AssertionError if the returned value does not match value.
Properties
  • .select: The DPOJET:MEAS<x>:LOGging:STATistics:SELect command.

select property 

select: DpojetMeasItemLoggingStatisticsSelect

Return the DPOJET:MEAS<x>:LOGging:STATistics:SELect command.

Description
  • This command sets or queries the given measurement for inclusion in any statistic logging. Statistic logging is turned on or off as a whole, using the DPOJET:LOGging branch.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:STATistics:SELect? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:STATistics:SELect? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOGging:STATistics:SELect value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:STATistics:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:STATistics:SELect?

DpojetMeasItemLoggingStatisticsSelect

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:LOGging:STATistics:SELect command.

Description
  • This command sets or queries the given measurement for inclusion in any statistic logging. Statistic logging is turned on or off as a whole, using the DPOJET:LOGging branch.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:STATistics:SELect? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:STATistics:SELect? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOGging:STATistics:SELect value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:STATistics:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:STATistics:SELect?

DpojetMeasItemLoggingWorstcase

Bases: SCPICmdRead

The DPOJET:MEAS<x>:LOGging:WORSTcase command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:WORSTcase? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:WORSTcase? query and raise an AssertionError if the returned value does not match value.
Properties
  • .select: The DPOJET:MEAS<x>:LOGging:WORSTcase:SELect command.

select property 

select: DpojetMeasItemLoggingWorstcaseSelect

Return the DPOJET:MEAS<x>:LOGging:WORSTcase:SELect command.

Description
  • This command sets or queries the given measurement for inclusion in any worst-case logging. Statistic logging is turned on or off as a whole, using the DPOJET:LOGging branch.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:WORSTcase:SELect? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:WORSTcase:SELect? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOGging:WORSTcase:SELect value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:WORSTcase:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:WORSTcase:SELect?

DpojetMeasItemLoggingWorstcaseSelect

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:LOGging:WORSTcase:SELect command.

Description
  • This command sets or queries the given measurement for inclusion in any worst-case logging. Statistic logging is turned on or off as a whole, using the DPOJET:LOGging branch.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOGging:WORSTcase:SELect? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOGging:WORSTcase:SELect? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOGging:WORSTcase:SELect value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOGging:WORSTcase:SELect {1|0}
- DPOJET:MEAS<x>:LOGging:WORSTcase:SELect?

DpojetMeasItemLowrefvoltage

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:LOWREFVoltage command.

Description
  • This command sets or queries the low reference voltage value for the selected configuration.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:LOWREFVoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:LOWREFVoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:LOWREFVoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:LOWREFVoltage <NR3>
- DPOJET:MEAS<x>:LOWREFVoltage?

DpojetMeasItemMargin

Bases: SCPICmdRead

The DPOJET:MEAS<x>:MARGIN command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN? query and raise an AssertionError if the returned value does not match value.
Properties
  • .hitcountvalue: The DPOJET:MEAS<x>:MARGIN:HITCOUNTValue command.
  • .hitratiostate: The DPOJET:MEAS<x>:MARGIN:HITRATIOState command.
  • .hitratiovalue: The DPOJET:MEAS<x>:MARGIN:HITRATIOValue command.
  • .resolution: The DPOJET:MEAS<x>:MARGIN:RESOlution command.

hitcountvalue property 

hitcountvalue: DpojetMeasItemMarginHitcountvalue

Return the DPOJET:MEAS<x>:MARGIN:HITCOUNTValue command.

Description
  • This command sets or queries the HitCount value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:HITCOUNTValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:HITCOUNTValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:HITCOUNTValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:HITCOUNTValue <NR3>
- DPOJET:MEAS<x>:MARGIN:HITCOUNTValue?

hitratiostate property 

hitratiostate: DpojetMeasItemMarginHitratiostate

Return the DPOJET:MEAS<x>:MARGIN:HITRATIOState command.

Description
  • This command sets or queries the HitRatio state.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:HITRATIOState {1|0}
- DPOJET:MEAS<x>:MARGIN:HITRATIOState?

hitratiovalue property 

hitratiovalue: DpojetMeasItemMarginHitratiovalue

Return the DPOJET:MEAS<x>:MARGIN:HITRATIOValue command.

Description
  • This command sets or queries the HitRatio value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:HITRATIOValue <NR3>
- DPOJET:MEAS<x>:MARGIN:HITRATIOValue?

resolution property 

resolution: DpojetMeasItemMarginResolution

Return the DPOJET:MEAS<x>:MARGIN:RESOlution command.

Description
  • This command sets or queries the resolution value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:RESOlution? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:RESOlution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:RESOlution value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:RESOlution <NR3>
- DPOJET:MEAS<x>:MARGIN:RESOlution?

DpojetMeasItemMarginHitcountvalue

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MARGIN:HITCOUNTValue command.

Description
  • This command sets or queries the HitCount value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:HITCOUNTValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:HITCOUNTValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:HITCOUNTValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:HITCOUNTValue <NR3>
- DPOJET:MEAS<x>:MARGIN:HITCOUNTValue?

DpojetMeasItemMarginHitratiostate

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MARGIN:HITRATIOState command.

Description
  • This command sets or queries the HitRatio state.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOState? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOState? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOState value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:HITRATIOState {1|0}
- DPOJET:MEAS<x>:MARGIN:HITRATIOState?

DpojetMeasItemMarginHitratiovalue

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MARGIN:HITRATIOValue command.

Description
  • This command sets or queries the HitRatio value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOValue? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:HITRATIOValue value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:HITRATIOValue <NR3>
- DPOJET:MEAS<x>:MARGIN:HITRATIOValue?

DpojetMeasItemMarginResolution

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MARGIN:RESOlution command.

Description
  • This command sets or queries the resolution value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MARGIN:RESOlution? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MARGIN:RESOlution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MARGIN:RESOlution value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MARGIN:RESOlution <NR3>
- DPOJET:MEAS<x>:MARGIN:RESOlution?

DpojetMeasItemMaskfile

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MASKfile command.

Description
  • This command sets or queries the current mask file name.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKfile? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKfile? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MASKfile value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKfile <string>
- DPOJET:MEAS<x>:MASKfile?

DpojetMeasItemMaskoffset

Bases: SCPICmdRead

The DPOJET:MEAS<x>:MASKOffset command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset? query and raise an AssertionError if the returned value does not match value.
Properties
  • .horizontal: The DPOJET:MEAS<x>:MASKOffset:HORizontal command tree.

horizontal property 

horizontal: DpojetMeasItemMaskoffsetHorizontal

Return the DPOJET:MEAS<x>:MASKOffset:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .autofit: The DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit command.
  • .manual: The DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual command.
  • .selectiontype: The DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype command.

DpojetMeasItemMaskoffsetHorizontal

Bases: SCPICmdRead

The DPOJET:MEAS<x>:MASKOffset:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .autofit: The DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit command.
  • .manual: The DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual command.
  • .selectiontype: The DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype command.

autofit property 

autofit: DpojetMeasItemMaskoffsetHorizontalAutofit

Return the DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit command.

Description
  • This query-only command returns the value in the Autofit text box for the Mask Offset controls. If the mask offset method selection type is set to Autofit and an acquisition cycle has been completed, this field shows the displacement of the mask offset that was automatically determined. A positive value means that the mask has moved to the right. If the offset has not been determined, the returned string is TBD.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit?

manual property 

manual: DpojetMeasItemMaskoffsetHorizontalManual

Return the DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual command.

Description
  • This command sets or queries the value for Manual text box.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual <NR3>
- DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual?

selectiontype property 

selectiontype: DpojetMeasItemMaskoffsetHorizontalSelectiontype

Return the DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype command.

Description
  • This command sets or queries the selection type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype { AUTOFIT|MANUAL}
- DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype?

DpojetMeasItemMaskoffsetHorizontalAutofit

Bases: SCPICmdRead

The DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit command.

Description
  • This query-only command returns the value in the Autofit text box for the Mask Offset controls. If the mask offset method selection type is set to Autofit and an acquisition cycle has been completed, this field shows the displacement of the mask offset that was automatically determined. A positive value means that the mask has moved to the right. If the offset has not been determined, the returned string is TBD.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKOffset:HORizontal:AUTOfit?

DpojetMeasItemMaskoffsetHorizontalManual

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual command.

Description
  • This command sets or queries the value for Manual text box.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual <NR3>
- DPOJET:MEAS<x>:MASKOffset:HORizontal:MANual?

DpojetMeasItemMaskoffsetHorizontalSelectiontype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype command.

Description
  • This command sets or queries the selection type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype { AUTOFIT|MANUAL}
- DPOJET:MEAS<x>:MASKOffset:HORizontal:SELECTIONtype?

DpojetMeasItemMeasrange

Bases: SCPICmdRead

The DPOJET:MEAS<x>:MEASRange command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange? query and raise an AssertionError if the returned value does not match value.
Properties
  • .max: The DPOJET:MEAS<x>:MEASRange:MAX command.
  • .min: The DPOJET:MEAS<x>:MEASRange:MIN command.
  • .state: The DPOJET:MEAS<x>:MEASRange:STATE command.

max property 

max: DpojetMeasItemMeasrangeMax

Return the DPOJET:MEAS<x>:MEASRange:MAX command.

Description
  • This command sets or queries the maximum measurement range limit value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange:MAX? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange:MAX? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASRange:MAX value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASRange:MAX <NR3>
- DPOJET:MEAS<x>:MEASRange:MAX?

min property 

min: DpojetMeasItemMeasrangeMin

Return the DPOJET:MEAS<x>:MEASRange:MIN command.

Description
  • This command sets or queries the minimum measurement range limit value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange:MIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange:MIN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASRange:MIN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASRange:MIN <NR3>
- DPOJET:MEAS<x>:MEASRange:MIN?

state property 

state: DpojetMeasItemMeasrangeState

Return the DPOJET:MEAS<x>:MEASRange:STATE command.

Description
  • This command turns on or off the measurement range limits.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange:STATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASRange:STATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASRange:STATE {1|0}
- DPOJET:MEAS<x>:MEASRange:STATE?

DpojetMeasItemMeasrangeMax

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MEASRange:MAX command.

Description
  • This command sets or queries the maximum measurement range limit value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange:MAX? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange:MAX? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASRange:MAX value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASRange:MAX <NR3>
- DPOJET:MEAS<x>:MEASRange:MAX?

DpojetMeasItemMeasrangeMin

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MEASRange:MIN command.

Description
  • This command sets or queries the minimum measurement range limit value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange:MIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange:MIN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASRange:MIN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASRange:MIN <NR3>
- DPOJET:MEAS<x>:MEASRange:MIN?

DpojetMeasItemMeasrangeState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MEASRange:STATE command.

Description
  • This command turns on or off the measurement range limits.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASRange:STATE? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASRange:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASRange:STATE value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASRange:STATE {1|0}
- DPOJET:MEAS<x>:MEASRange:STATE?

DpojetMeasItemMeasstart

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:MEASStart command.

Description
  • This command sets or queries the measurement start value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:MEASStart? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:MEASStart? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:MEASStart value command.
SCPI Syntax 
- DPOJET:MEAS<x>:MEASStart <NR3>
- DPOJET:MEAS<x>:MEASStart?

DpojetMeasItemN

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:N command.

Description
  • This command sets or queries the measurement N value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:N? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:N? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:N value command.
SCPI Syntax 
- DPOJET:MEAS<x>:N <NR3>
- DPOJET:MEAS<x>:N?

DpojetMeasItemName

Bases: SCPICmdRead

The DPOJET:MEAS<x>:NAME command.

Description
  • This query-only command returns the measurement name for the measurement in slot x. For measurements that include 16-bit characters in their UI names, such as DJDirac, the string returned will contain question marks where the UI contains nontext characters.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:NAME? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:NAME? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:NAME?

DpojetMeasItemOptical

Bases: SCPICmdRead

The DPOJET:MEAS<x>:OPTIcal command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .bandwidth: The DPOJET:MEAS<x>:OPTIcal:BANDWIDth command.
  • .btfilter: The DPOJET:MEAS<x>:OPTIcal:BTFILTEr command.
  • .ffetaps: The DPOJET:MEAS<x>:OPTIcal:FFETAPS command.
  • .scopern: The DPOJET:MEAS<x>:OPTIcal:SCOPERN command.
  • .targetber: The DPOJET:MEAS<x>:OPTIcal:TARGETBer command.
  • .wfmtype: The DPOJET:MEAS<x>:OPTIcal:WFMTYpe command.

bandwidth property 

bandwidth: DpojetMeasItemOpticalBandwidth

Return the DPOJET:MEAS<x>:OPTIcal:BANDWIDth command.

Description
  • This command sets or queries the optical to electrical converted bandwidth value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:BANDWIDth? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:BANDWIDth? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:BANDWIDth value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:BANDWIDth <NR3>
- DPOJET:MEAS<x>:OPTIcal:BANDWIDth?

btfilter property 

btfilter: DpojetMeasItemOpticalBtfilter

Return the DPOJET:MEAS<x>:OPTIcal:BTFILTEr command.

Description
  • This command sets or queries current BT Filter file with absolute path.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:BTFILTEr? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:BTFILTEr? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:BTFILTEr value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:BTFILTEr <string>
- DPOJET:MEAS<x>:OPTIcal:BTFILTEr?

ffetaps property 

ffetaps: DpojetMeasItemOpticalFfetaps

Return the DPOJET:MEAS<x>:OPTIcal:FFETAPS command.

Description
  • This command sets or queries current FFE tap file with absolute path.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:FFETAPS? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:FFETAPS? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:FFETAPS value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:FFETAPS <string>
- DPOJET:MEAS<x>:OPTIcal:FFETAPS?

scopern property 

scopern: DpojetMeasItemOpticalScopern

Return the DPOJET:MEAS<x>:OPTIcal:SCOPERN command.

Description
  • This command sets or queries the Scope RN(rms) value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:SCOPERN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:SCOPERN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:SCOPERN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:SCOPERN <NR3>
- DPOJET:MEAS<x>:OPTIcal:SCOPERN?

targetber property 

targetber: DpojetMeasItemOpticalTargetber

Return the DPOJET:MEAS<x>:OPTIcal:TARGETBer command.

Description
  • This command sets or queries the Target BER value display. The 1E-Value = 10 -Value will be considered as Target BER for the TDEC computation.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:TARGETBer? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:TARGETBer? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:TARGETBer value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:TARGETBer <NR3>
- DPOJET:MEAS<x>:OPTIcal:TARGETBer?

wfmtype property 

wfmtype: DpojetMeasItemOpticalWfmtype

Return the DPOJET:MEAS<x>:OPTIcal:WFMTYpe command.

Description
  • This command sets or queries the optical waveform type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:WFMTYpe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:WFMTYpe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:WFMTYpe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:WFMTYpe {CONTINUOUS|MODULATED}
- DPOJET:MEAS<x>:OPTIcal:WFMTYpe?

DpojetMeasItemOpticalBandwidth

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:OPTIcal:BANDWIDth command.

Description
  • This command sets or queries the optical to electrical converted bandwidth value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:BANDWIDth? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:BANDWIDth? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:BANDWIDth value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:BANDWIDth <NR3>
- DPOJET:MEAS<x>:OPTIcal:BANDWIDth?

DpojetMeasItemOpticalBtfilter

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:OPTIcal:BTFILTEr command.

Description
  • This command sets or queries current BT Filter file with absolute path.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:BTFILTEr? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:BTFILTEr? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:BTFILTEr value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:BTFILTEr <string>
- DPOJET:MEAS<x>:OPTIcal:BTFILTEr?

DpojetMeasItemOpticalFfetaps

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:OPTIcal:FFETAPS command.

Description
  • This command sets or queries current FFE tap file with absolute path.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:FFETAPS? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:FFETAPS? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:FFETAPS value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:FFETAPS <string>
- DPOJET:MEAS<x>:OPTIcal:FFETAPS?

DpojetMeasItemOpticalScopern

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:OPTIcal:SCOPERN command.

Description
  • This command sets or queries the Scope RN(rms) value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:SCOPERN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:SCOPERN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:SCOPERN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:SCOPERN <NR3>
- DPOJET:MEAS<x>:OPTIcal:SCOPERN?

DpojetMeasItemOpticalTargetber

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:OPTIcal:TARGETBer command.

Description
  • This command sets or queries the Target BER value display. The 1E-Value = 10 -Value will be considered as Target BER for the TDEC computation.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:TARGETBer? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:TARGETBer? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:TARGETBer value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:TARGETBer <NR3>
- DPOJET:MEAS<x>:OPTIcal:TARGETBer?

DpojetMeasItemOpticalWfmtype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:OPTIcal:WFMTYpe command.

Description
  • This command sets or queries the optical waveform type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:OPTIcal:WFMTYpe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:OPTIcal:WFMTYpe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:OPTIcal:WFMTYpe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:OPTIcal:WFMTYpe {CONTINUOUS|MODULATED}
- DPOJET:MEAS<x>:OPTIcal:WFMTYpe?

DpojetMeasItemPhasenoise

Bases: SCPICmdRead

The DPOJET:MEAS<x>:PHASENoise command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PHASENoise? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PHASENoise? query and raise an AssertionError if the returned value does not match value.
Properties
  • .highlimit: The DPOJET:MEAS<x>:PHASENoise:HIGHLimit command.
  • .lowlimit: The DPOJET:MEAS<x>:PHASENoise:LOWLimit command.

highlimit property 

highlimit: DpojetMeasItemPhasenoiseHighlimit

Return the DPOJET:MEAS<x>:PHASENoise:HIGHLimit command.

Description
  • This command sets or queries the upper phase noise integration limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PHASENoise:HIGHLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PHASENoise:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:PHASENoise:HIGHLimit value command.
SCPI Syntax 
- DPOJET:MEAS<x>:PHASENoise:HIGHLimit <NR3>
- DPOJET:MEAS<x>:PHASENoise:HIGHLimit?

lowlimit property 

lowlimit: DpojetMeasItemPhasenoiseLowlimit

Return the DPOJET:MEAS<x>:PHASENoise:LOWLimit command.

Description
  • This command sets or queries the lower phase noise integration limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PHASENoise:LOWLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PHASENoise:LOWLimit? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:PHASENoise:LOWLimit value command.
SCPI Syntax 
- DPOJET:MEAS<x>:PHASENoise:LOWLimit <NR3>
- DPOJET:MEAS<x>:PHASENoise:LOWLimit?

DpojetMeasItemPhasenoiseHighlimit

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:PHASENoise:HIGHLimit command.

Description
  • This command sets or queries the upper phase noise integration limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PHASENoise:HIGHLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PHASENoise:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:PHASENoise:HIGHLimit value command.
SCPI Syntax 
- DPOJET:MEAS<x>:PHASENoise:HIGHLimit <NR3>
- DPOJET:MEAS<x>:PHASENoise:HIGHLimit?

DpojetMeasItemPhasenoiseLowlimit

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:PHASENoise:LOWLimit command.

Description
  • This command sets or queries the lower phase noise integration limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PHASENoise:LOWLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PHASENoise:LOWLimit? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:PHASENoise:LOWLimit value command.
SCPI Syntax 
- DPOJET:MEAS<x>:PHASENoise:LOWLimit <NR3>
- DPOJET:MEAS<x>:PHASENoise:LOWLimit?

DpojetMeasItemPlotfiles

Bases: SCPICmdRead

The DPOJET:MEAS<x>:PLOTFILES command.

Description
  • The query-only command returns plot file paths of a given measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:PLOTFILES? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:PLOTFILES? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:PLOTFILES?

DpojetMeasItemRefvoltage

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:REFVoltage command.

Description
  • This command sets or queries the reference voltage for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:REFVoltage? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:REFVoltage? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:REFVoltage value command.
SCPI Syntax 
- DPOJET:MEAS<x>:REFVoltage {100|—100}
- DPOJET:MEAS<x>:REFVoltage?

DpojetMeasItemResults

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts command.

Description
  • This query-only command returns the measurement branch for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts?
Properties
  • .allacqs: The DPOJET:MEAS<x>:RESULts:ALLAcqs command.
  • .currentacq: The DPOJET:MEAS<x>:RESULts:CURRentacq command tree.
  • .getall: The DPOJET:MEAS<x>:RESULts:GETAll command.
  • .status: The DPOJET:MEAS<x>:RESULts:STATus command.
  • .view: The DPOJET:MEAS<x>:RESULts:VIew command.

allacqs property 

allacqs: DpojetMeasItemResultsAllacqs

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs command.

Description
  • This query-only command returns the measurement results from all acquisitions.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs?
Sub-properties
  • .hitpopulation: The DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation command.
  • .hits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS command.
  • .limits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits command tree.
  • .max: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX command.
  • .maxcc: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC command.
  • .maxhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits command.
  • .mean: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN command.
  • .min: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN command.
  • .mincc: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC command.
  • .minhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits command.
  • .pk2pk: The DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK command.
  • .population: The DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation command.
  • .seg: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x> command tree.
  • .stddev: The DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev command.

currentacq property 

currentacq: DpojetMeasItemResultsCurrentacq

Return the DPOJET:MEAS<x>:RESULts:CURRentacq command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .max: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAX command.
  • .maxcc: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC command.
  • .mean: The DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN command.
  • .min: The DPOJET:MEAS<x>:RESULts:CURRentacq:MIN command.
  • .mincc: The DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC command.
  • .pk2pk: The DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK command.
  • .population: The DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation command.
  • .stddev: The DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev command.

getall property 

getall: DpojetMeasItemResultsGetall

Return the DPOJET:MEAS<x>:RESULts:GETAll command.

Description
  • The query-only command returns results of given measurement in xml format with units.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:GETAll? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:GETAll? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:GETAll?

status property 

status: DpojetMeasItemResultsStatus

Return the DPOJET:MEAS<x>:RESULts:STATus command.

Description
  • This query-only command returns the status of the given measurement values in slot MEAS. Valid for currently valid measurements, or the error status such as ‘Not enough edges’.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:STATus?

view property 

view: DpojetMeasItemResultsView

Return the DPOJET:MEAS<x>:RESULts:VIew command.

Description
  • This query-only command returns the results view type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:VIew? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:VIew? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:VIew?

DpojetMeasItemResultsAllacqs

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs command.

Description
  • This query-only command returns the measurement results from all acquisitions.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs?
Properties
  • .hitpopulation: The DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation command.
  • .hits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS command.
  • .limits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits command tree.
  • .max: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX command.
  • .maxcc: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC command.
  • .maxhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits command.
  • .mean: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN command.
  • .min: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN command.
  • .mincc: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC command.
  • .minhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits command.
  • .pk2pk: The DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK command.
  • .population: The DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation command.
  • .seg: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x> command tree.
  • .stddev: The DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev command.

hitpopulation property 

hitpopulation: DpojetMeasItemResultsAllacqsHitpopulation

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation command.

Description
  • This query-only command returns the mask hit population.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation?

hits property 

hits: DpojetMeasItemResultsAllacqsHits

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS command.

Description
  • This query-only command returns the mask hits measurement for all segments.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS?

limits property 

limits: DpojetMeasItemResultsAllacqsLimits

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .high: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh command tree.
  • .low: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw command tree.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus command.

max property 

max: DpojetMeasItemResultsAllacqsMax

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX command.

Description
  • This query-only command returns the maximum value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX?
Sub-properties
  • .highlimit: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit command.
  • .highmargin: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin command.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus command.

maxcc property 

maxcc: DpojetMeasItemResultsAllacqsMaxcc

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC command.

Description
  • This query-only command returns the maximum positive cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus command.

maxhits property 

maxhits: DpojetMeasItemResultsAllacqsMaxhits

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits command.

Description
  • This query-only command returns the maximum mask hits measurement for all segments.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits?

mean property 

mean: DpojetMeasItemResultsAllacqsMean

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN command.

Description
  • This query-only command returns the mean value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN?
Sub-properties
  • .highlimit: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit command.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus command.

min property 

min: DpojetMeasItemResultsAllacqsMin

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN command.

Description
  • This query-only command returns the minimum value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN?
Sub-properties
  • .lowlimit: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit command.
  • .lowmargin: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin command.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus command.

mincc property 

mincc: DpojetMeasItemResultsAllacqsMincc

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC command.

Description
  • This query-only command returns the maximum negative cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus command.

minhits property 

minhits: DpojetMeasItemResultsAllacqsMinhits

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits command.

Description
  • This query-only command returns the minimum mask hits measurement for all segments.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits?

pk2pk property 

pk2pk: DpojetMeasItemResultsAllacqsPk2pk

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK command.

Description
  • This query-only command returns the peak-to-peak value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus command.

population property 

population: DpojetMeasItemResultsAllacqsPopulation

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation command.

Description
  • This query-only command returns the mean measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus command.

seg property 

seg: dict[int, DpojetMeasItemResultsAllacqsSegItem]

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .hits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits command.
  • .maxhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits command.
  • .minhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits command.

stddev property 

stddev: DpojetMeasItemResultsAllacqsStddev

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev command.

Description
  • This query-only command returns the standard deviation for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus command.

DpojetMeasItemResultsAllacqsHitpopulation

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation command.

Description
  • This query-only command returns the mask hit population.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:HITPopulation?

DpojetMeasItemResultsAllacqsHits

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS command.

Description
  • This query-only command returns the mask hits measurement for all segments.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:HITS?

DpojetMeasItemResultsAllacqsLimits

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits? query and raise an AssertionError if the returned value does not match value.
Properties
  • .high: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh command tree.
  • .low: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw command tree.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus command.

high property 

high: DpojetMeasItemResultsAllacqsLimitsHigh

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus command.

low property 

low: DpojetMeasItemResultsAllacqsLimitsLow

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsLimitsStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus command.

Description
  • This query-only command returns the pass/fail status per measurement. If any of the statistics fails, the cumulative result is fail, otherwise pass.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus?

DpojetMeasItemResultsAllacqsLimitsHigh

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh? query and raise an AssertionError if the returned value does not match value.
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsLimitsHighStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus command.

Description
  • This query-only command returns the pass/fail status for high limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus?

DpojetMeasItemResultsAllacqsLimitsHighStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus command.

Description
  • This query-only command returns the pass/fail status for high limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:HIgh:STATus?

DpojetMeasItemResultsAllacqsLimitsLow

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw? query and raise an AssertionError if the returned value does not match value.
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsLimitsLowStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus command.

Description
  • This query-only command returns the pass/fail status for low limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus?

DpojetMeasItemResultsAllacqsLimitsLowStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus command.

Description
  • This query-only command returns the pass/fail status for low limit.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:LOw:STATus?

DpojetMeasItemResultsAllacqsLimitsStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus command.

Description
  • This query-only command returns the pass/fail status per measurement. If any of the statistics fails, the cumulative result is fail, otherwise pass.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:LIMits:STATus?

DpojetMeasItemResultsAllacqsMax

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX command.

Description
  • This query-only command returns the maximum value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX?
Properties
  • .highlimit: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit command.
  • .highmargin: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin command.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus command.

highlimit property 

highlimit: DpojetMeasItemResultsAllacqsMaxHighlimit

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit command.

Description
  • This query-only command returns the high limit value of Max for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit?

highmargin property 

highmargin: DpojetMeasItemResultsAllacqsMaxHighmargin

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin command.

Description
  • This query-only command returns the high margin value of Max for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin?

status property 

status: DpojetMeasItemResultsAllacqsMaxStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus command.

Description
  • This query-only command returns the pass/fail status for the max measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus?

DpojetMeasItemResultsAllacqsMaxHighlimit

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit command.

Description
  • This query-only command returns the high limit value of Max for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHLimit?

DpojetMeasItemResultsAllacqsMaxHighmargin

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin command.

Description
  • This query-only command returns the high margin value of Max for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:HIGHMArgin?

DpojetMeasItemResultsAllacqsMaxStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus command.

Description
  • This query-only command returns the pass/fail status for the max measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAX:STATus?

DpojetMeasItemResultsAllacqsMaxcc

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC command.

Description
  • This query-only command returns the maximum positive cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsMaxccStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the maximum positive cycle-to-cycle delta of the selected measurement (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus?

DpojetMeasItemResultsAllacqsMaxccStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the maximum positive cycle-to-cycle delta of the selected measurement (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXCC:STATus?

DpojetMeasItemResultsAllacqsMaxhits

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits command.

Description
  • This query-only command returns the maximum mask hits measurement for all segments.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MAXHits?

DpojetMeasItemResultsAllacqsMean

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN command.

Description
  • This query-only command returns the mean value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN?
Properties
  • .highlimit: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit command.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus command.

highlimit property 

highlimit: DpojetMeasItemResultsAllacqsMeanHighlimit

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit command.

Description
  • This query-only command returns the high limit value of Mean for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit?

status property 

status: DpojetMeasItemResultsAllacqsMeanStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus command.

Description
  • This query-only command returns the pass/fail status for the mean measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus?

DpojetMeasItemResultsAllacqsMeanHighlimit

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit command.

Description
  • This query-only command returns the high limit value of Mean for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:HIGHLimit?

DpojetMeasItemResultsAllacqsMeanStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus command.

Description
  • This query-only command returns the pass/fail status for the mean measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MEAN:STATus?

DpojetMeasItemResultsAllacqsMin

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN command.

Description
  • This query-only command returns the minimum value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN?
Properties
  • .lowlimit: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit command.
  • .lowmargin: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin command.
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus command.

lowlimit property 

lowlimit: DpojetMeasItemResultsAllacqsMinLowlimit

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit command.

Description
  • This query-only command returns the low limit value of Min for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit?

lowmargin property 

lowmargin: DpojetMeasItemResultsAllacqsMinLowmargin

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin command.

Description
  • This query-only command returns the low margin value of Min for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin?

status property 

status: DpojetMeasItemResultsAllacqsMinStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus command.

Description
  • This query-only command returns the pass/fail status for the minimum measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus?

DpojetMeasItemResultsAllacqsMinLowlimit

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit command.

Description
  • This query-only command returns the low limit value of Min for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWLimit?

DpojetMeasItemResultsAllacqsMinLowmargin

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin command.

Description
  • This query-only command returns the low margin value of Min for measurement .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:LOWMArgin?

DpojetMeasItemResultsAllacqsMinStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus command.

Description
  • This query-only command returns the pass/fail status for the minimum measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MIN:STATus?

DpojetMeasItemResultsAllacqsMincc

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC command.

Description
  • This query-only command returns the maximum negative cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsMinccStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the negative cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus?

DpojetMeasItemResultsAllacqsMinccStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the negative cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINCC:STATus?

DpojetMeasItemResultsAllacqsMinhits

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits command.

Description
  • This query-only command returns the minimum mask hits measurement for all segments.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:MINHits?

DpojetMeasItemResultsAllacqsPk2pk

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK command.

Description
  • This query-only command returns the peak-to-peak value for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsPk2pkStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus command.

Description
  • This query-only command returns the pass/fail status for the peak-to-peak measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus?

DpojetMeasItemResultsAllacqsPk2pkStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus command.

Description
  • This query-only command returns the pass/fail status for the peak-to-peak measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:PK2PK:STATus?

DpojetMeasItemResultsAllacqsPopulation

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation command.

Description
  • This query-only command returns the mean measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsPopulationStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus command.

Description
  • This query-only command returns the pass/fail status for the population measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus?

DpojetMeasItemResultsAllacqsPopulationStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus command.

Description
  • This query-only command returns the pass/fail status for the population measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:POPUlation:STATus?

DpojetMeasItemResultsAllacqsSegItem

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>? query and raise an AssertionError if the returned value does not match value.
Properties
  • .hits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits command.
  • .maxhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits command.
  • .minhits: The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits command.

hits property 

hits: DpojetMeasItemResultsAllacqsSegItemHits

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits command.

Description
  • This query-only command returns the mask hits measurement for the given segment, either SEG1, SEG2 or SEG3.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits?

maxhits property 

maxhits: DpojetMeasItemResultsAllacqsSegItemMaxhits

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits command.

Description
  • This query-only command returnseturns the maximum mask hits measurement for the given segment, either SEG1, SEG2 or SEG3.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits?

minhits property 

minhits: DpojetMeasItemResultsAllacqsSegItemMinhits

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits command.

Description
  • This query-only command returns the minimum mask hits measurement for the given segment, either SEG1, SEG2 or SEG3.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits?

DpojetMeasItemResultsAllacqsSegItemHits

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits command.

Description
  • This query-only command returns the mask hits measurement for the given segment, either SEG1, SEG2 or SEG3.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:Hits?

DpojetMeasItemResultsAllacqsSegItemMaxhits

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits command.

Description
  • This query-only command returnseturns the maximum mask hits measurement for the given segment, either SEG1, SEG2 or SEG3.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MAXHits?

DpojetMeasItemResultsAllacqsSegItemMinhits

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits command.

Description
  • This query-only command returns the minimum mask hits measurement for the given segment, either SEG1, SEG2 or SEG3.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:SEG<x>:MINHits?

DpojetMeasItemResultsAllacqsStddev

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev command.

Description
  • This query-only command returns the standard deviation for all accumulated measurement acquisitions for slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus command.

status property 

status: DpojetMeasItemResultsAllacqsStddevStatus

Return the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus command.

Description
  • This query-only command returns the pass/fail status for the standard deviation measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus?

DpojetMeasItemResultsAllacqsStddevStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus command.

Description
  • This query-only command returns the pass/fail status for the standard deviation measurement for the currently loaded limit file (set via :DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:ALLAcqs:STDDev:STATus?

DpojetMeasItemResultsCurrentacq

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq? query and raise an AssertionError if the returned value does not match value.
Properties
  • .max: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAX command.
  • .maxcc: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC command.
  • .mean: The DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN command.
  • .min: The DPOJET:MEAS<x>:RESULts:CURRentacq:MIN command.
  • .mincc: The DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC command.
  • .pk2pk: The DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK command.
  • .population: The DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation command.
  • .stddev: The DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev command.

max property 

max: DpojetMeasItemResultsCurrentacqMax

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX command.

Description
  • This query-only command returns the maximum value of the measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAX?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus command.

maxcc property 

maxcc: DpojetMeasItemResultsCurrentacqMaxcc

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC command.

Description
  • This query-only command returns the maximum positive cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus command.

mean property 

mean: DpojetMeasItemResultsCurrentacqMean

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN command.

Description
  • This query-only command returns the mean value of the measurement for the current acquisition or for the most recent processing cycle.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus command.

min property 

min: DpojetMeasItemResultsCurrentacqMin

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN command.

Description
  • This query-only command returns the minimum value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MIN?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus command.

mincc property 

mincc: DpojetMeasItemResultsCurrentacqMincc

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC command.

Description
  • This query-only command returns the maximum negative cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus command.

pk2pk property 

pk2pk: DpojetMeasItemResultsCurrentacqPk2pk

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK command.

Description
  • This query-only command returns the peak-to-peak value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus command.

population property 

population: DpojetMeasItemResultsCurrentacqPopulation

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation command.

Description
  • This query-only command returns the population measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus command.

stddev property 

stddev: DpojetMeasItemResultsCurrentacqStddev

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev command.

Description
  • This query-only command returns the standard deviation of the measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev?
Sub-properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus command.

DpojetMeasItemResultsCurrentacqMax

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MAX command.

Description
  • This query-only command returns the maximum value of the measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAX?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqMaxStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus command.

Description
  • This query-only command returns the pass/fail status for the max measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus?

DpojetMeasItemResultsCurrentacqMaxStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus command.

Description
  • This query-only command returns the pass/fail status for the max measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAX:STATus?

DpojetMeasItemResultsCurrentacqMaxcc

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC command.

Description
  • This query-only command returns the maximum positive cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqMaxccStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the Max cycle-to-cycle measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus?

DpojetMeasItemResultsCurrentacqMaxccStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the Max cycle-to-cycle measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MAXCC:STATus?

DpojetMeasItemResultsCurrentacqMean

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN command.

Description
  • This query-only command returns the mean value of the measurement for the current acquisition or for the most recent processing cycle.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqMeanStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus command.

Description
  • This query-only command returns the pass/fail status for the mean measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus?

DpojetMeasItemResultsCurrentacqMeanStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus command.

Description
  • This query-only command returns the pass/fail status for the mean measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MEAN:STATus?

DpojetMeasItemResultsCurrentacqMin

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MIN command.

Description
  • This query-only command returns the minimum value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MIN?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqMinStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus command.

Description
  • This query-only command returns the pass/fail status for the minimum measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus?

DpojetMeasItemResultsCurrentacqMinStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus command.

Description
  • This query-only command returns the pass/fail status for the minimum measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MIN:STATus?

DpojetMeasItemResultsCurrentacqMincc

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC command.

Description
  • This query-only command returns the maximum negative cycle-to-cycle delta of the selected measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqMinccStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the min cycle-to-cycle measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus?

DpojetMeasItemResultsCurrentacqMinccStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus command.

Description
  • This query-only command returns the pass/fail status for the min cycle-to-cycle measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:MINCC:STATus?

DpojetMeasItemResultsCurrentacqPk2pk

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK command.

Description
  • This query-only command returns the peak-to-peak value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqPk2pkStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus command.

Description
  • This query-only command returns the pass/fail status for the peak-to-peak measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus?

DpojetMeasItemResultsCurrentacqPk2pkStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus command.

Description
  • This query-only command returns the pass/fail status for the peak-to-peak measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:PK2PK:STATus?

DpojetMeasItemResultsCurrentacqPopulation

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation command.

Description
  • This query-only command returns the population measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqPopulationStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus command.

Description
  • This query-only command returns the pass/fail status for the population measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus?

DpojetMeasItemResultsCurrentacqPopulationStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus command.

Description
  • This query-only command returns the pass/fail status for the population measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:POPUlation:STATus?

DpojetMeasItemResultsCurrentacqStddev

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev command.

Description
  • This query-only command returns the standard deviation of the measurement value for the currently selected measurement for measurement slot .
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev?
Properties
  • .status: The DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus command.

status property 

status: DpojetMeasItemResultsCurrentacqStddevStatus

Return the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus command.

Description
  • This query-only command returns the pass/fail status for the standard deviation measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus?

DpojetMeasItemResultsCurrentacqStddevStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus command.

Description
  • This query-only command returns the pass/fail status for the standard deviation measurement for the currently loaded limit file. (Set using DPOJET:LIMits:FILEName).
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:CURRentacq:STDDev:STATus?

DpojetMeasItemResultsGetall

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:GETAll command.

Description
  • The query-only command returns results of given measurement in xml format with units.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:GETAll? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:GETAll? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:GETAll?

DpojetMeasItemResultsStatus

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:STATus command.

Description
  • This query-only command returns the status of the given measurement values in slot MEAS. Valid for currently valid measurements, or the error status such as ‘Not enough edges’.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:STATus? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:STATus?

DpojetMeasItemResultsView

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RESULts:VIew command.

Description
  • This query-only command returns the results view type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RESULts:VIew? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RESULts:VIew? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:RESULts:VIew?

DpojetMeasItemRjdj

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RJDJ command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ber: The DPOJET:MEAS<x>:RJDJ:BER command.
  • .detectplen: The DPOJET:MEAS<x>:RJDJ:DETECTPLEN command.
  • .ncmode: The DPOJET:MEAS<x>:RJDJ:NCMODe command.
  • .patlen: The DPOJET:MEAS<x>:RJDJ:PATLen command.
  • .scopern: The DPOJET:MEAS<x>:RJDJ:SCOPERN command.
  • .sncrefid: The DPOJET:MEAS<x>:RJDJ:SNCREFID command.
  • .type: The DPOJET:MEAS<x>:RJDJ:TYPe command.
  • .windowlength: The DPOJET:MEAS<x>:RJDJ:WINDOwlength command.

ber property 

ber: DpojetMeasItemRjdjBer

Return the DPOJET:MEAS<x>:RJDJ:BER command.

Description
  • This command sets or queries the RJDJ Target BER value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:BER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:BER value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:BER <NR3>
- DPOJET:MEAS<x>:RJDJ:BER?

detectplen property 

detectplen: DpojetMeasItemRjdjDetectplen

Return the DPOJET:MEAS<x>:RJDJ:DETECTPLEN command.

Description
  • This command sets or queries the current detect plan.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:DETECTPLEN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:DETECTPLEN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:DETECTPLEN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:DETECTPLEN {ON|OFF|1|0}
- DPOJET:MEAS<x>:RJDJ:DETECTPLEN?

ncmode property 

ncmode: DpojetMeasItemRjdjNcmode

Return the DPOJET:MEAS<x>:RJDJ:NCMODe command.

Description
  • This command sets or queries the noise compensation mode, Auto or Manual.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:NCMODe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:NCMODe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:NCMODe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:NCMODe {1|0}
- DPOJET:MEAS<x>:RJDJ:NCMODe?

patlen property 

patlen: DpojetMeasItemRjdjPatlen

Return the DPOJET:MEAS<x>:RJDJ:PATLen command.

Description
  • This command sets or queries the current RJDJ pattern length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:PATLen? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:PATLen? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:PATLen value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:PATLen <NR3>
- DPOJET:MEAS<x>:RJDJ:PATLen?

scopern property 

scopern: DpojetMeasItemRjdjScopern

Return the DPOJET:MEAS<x>:RJDJ:SCOPERN command.

Description
  • This command to sets or queries the scope noise value from the applicable measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:SCOPERN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:SCOPERN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:SCOPERN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:SCOPERN <NR3>
- DPOJET:MEAS<x>:RJDJ:SCOPERN?

sncrefid property 

sncrefid: DpojetMeasItemRjdjSncrefid

Return the DPOJET:MEAS<x>:RJDJ:SNCREFID command.

Description
  • This command sets or queries the reference id which is used for fetching the noise value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:SNCREFID? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:SNCREFID? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:SNCREFID value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:SNCREFID <string>
- DPOJET:MEAS<x>:RJDJ:SNCREFID?

type property 

type: DpojetMeasItemRjdjType

Return the DPOJET:MEAS<x>:RJDJ:TYPe command.

Description
  • This command sets or queries the current RJDJ measurement type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:TYPe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:TYPe {ARBITrary|REPEating}
- DPOJET:MEAS<x>:RJDJ:TYPe?

windowlength property 

windowlength: DpojetMeasItemRjdjWindowlength

Return the DPOJET:MEAS<x>:RJDJ:WINDOwlength command.

Description
  • This command sets or queries the current RJDJ window length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:WINDOwlength? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:WINDOwlength? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:WINDOwlength value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:WINDOwlength <NR3>
- DPOJET:MEAS<x>:RJDJ:WINDOwlength?

DpojetMeasItemRjdjBer

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:BER command.

Description
  • This command sets or queries the RJDJ Target BER value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:BER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:BER value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:BER <NR3>
- DPOJET:MEAS<x>:RJDJ:BER?

DpojetMeasItemRjdjDetectplen

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:DETECTPLEN command.

Description
  • This command sets or queries the current detect plan.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:DETECTPLEN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:DETECTPLEN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:DETECTPLEN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:DETECTPLEN {ON|OFF|1|0}
- DPOJET:MEAS<x>:RJDJ:DETECTPLEN?

DpojetMeasItemRjdjNcmode

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:NCMODe command.

Description
  • This command sets or queries the noise compensation mode, Auto or Manual.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:NCMODe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:NCMODe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:NCMODe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:NCMODe {1|0}
- DPOJET:MEAS<x>:RJDJ:NCMODe?

DpojetMeasItemRjdjPatlen

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:PATLen command.

Description
  • This command sets or queries the current RJDJ pattern length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:PATLen? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:PATLen? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:PATLen value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:PATLen <NR3>
- DPOJET:MEAS<x>:RJDJ:PATLen?

DpojetMeasItemRjdjScopern

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:SCOPERN command.

Description
  • This command to sets or queries the scope noise value from the applicable measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:SCOPERN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:SCOPERN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:SCOPERN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:SCOPERN <NR3>
- DPOJET:MEAS<x>:RJDJ:SCOPERN?

DpojetMeasItemRjdjSncrefid

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:SNCREFID command.

Description
  • This command sets or queries the reference id which is used for fetching the noise value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:SNCREFID? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:SNCREFID? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:SNCREFID value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:SNCREFID <string>
- DPOJET:MEAS<x>:RJDJ:SNCREFID?

DpojetMeasItemRjdjType

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:TYPe command.

Description
  • This command sets or queries the current RJDJ measurement type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:TYPe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:TYPe {ARBITrary|REPEating}
- DPOJET:MEAS<x>:RJDJ:TYPe?

DpojetMeasItemRjdjWindowlength

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RJDJ:WINDOwlength command.

Description
  • This command sets or queries the current RJDJ window length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RJDJ:WINDOwlength? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RJDJ:WINDOwlength? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RJDJ:WINDOwlength value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RJDJ:WINDOwlength <NR3>
- DPOJET:MEAS<x>:RJDJ:WINDOwlength?

DpojetMeasItemRndn

Bases: SCPICmdRead

The DPOJET:MEAS<x>:RNDN command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN? query and raise an AssertionError if the returned value does not match value.
Properties
  • .autodetectpattern: The DPOJET:MEAS<x>:RNDN:AUTODETECTpattern command.
  • .ber: The DPOJET:MEAS<x>:RNDN:BER command.
  • .ncmode: The DPOJET:MEAS<x>:RNDN:NCMODe command.
  • .patlen: The DPOJET:MEAS<x>:RNDN:PATLen command.
  • .scopern: The DPOJET:MEAS<x>:RNDN:SCOPERN command.
  • .sncrefid: The DPOJET:MEAS<x>:RNDN:SNCREFID command.
  • .type: The DPOJET:MEAS<x>:RNDN:TYPe command.
  • .windowlength: The DPOJET:MEAS<x>:RNDN:WINDOwlength command.

autodetectpattern property 

autodetectpattern: DpojetMeasItemRndnAutodetectpattern

Return the DPOJET:MEAS<x>:RNDN:AUTODETECTpattern command.

Description
  • This command sets or queries the current pattern detection control plan.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:AUTODETECTpattern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:AUTODETECTpattern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:AUTODETECTpattern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:AUTODETECTpattern {ON|OFF|1|0}
- DPOJET:MEAS<x>:RNDN:AUTODETECTpattern?

ber property 

ber: DpojetMeasItemRndnBer

Return the DPOJET:MEAS<x>:RNDN:BER command.

Description
  • This command sets or queries the RNDN Target BER value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:BER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:BER value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:BER <NR3>
- DPOJET:MEAS<x>:RNDN:BER?

ncmode property 

ncmode: DpojetMeasItemRndnNcmode

Return the DPOJET:MEAS<x>:RNDN:NCMODe command.

Description
  • This command sets or queries the noise compensation mode.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:NCMODe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:NCMODe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:NCMODe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:NCMODe {1|0}
- DPOJET:MEAS<x>:RNDN:NCMODe?

patlen property 

patlen: DpojetMeasItemRndnPatlen

Return the DPOJET:MEAS<x>:RNDN:PATLen command.

Description
  • This command sets or queries the current RNDN pattern length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:PATLen? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:PATLen? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:PATLen value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:PATLen <NR3>
- DPOJET:MEAS<x>:RNDN:PATLen?

scopern property 

scopern: DpojetMeasItemRndnScopern

Return the DPOJET:MEAS<x>:RNDN:SCOPERN command.

Description
  • This command to sets or queries the scope noise value from the applicable measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:SCOPERN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:SCOPERN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:SCOPERN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:SCOPERN <NR3>
- DPOJET:MEAS<x>:RNDN:SCOPERN?

sncrefid property 

sncrefid: DpojetMeasItemRndnSncrefid

Return the DPOJET:MEAS<x>:RNDN:SNCREFID command.

Description
  • This command sets or queries the reference id which is used for fetching the noise value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:SNCREFID? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:SNCREFID? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:SNCREFID value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:SNCREFID <string>
- DPOJET:MEAS<x>:RNDN:SNCREFID?

type property 

type: DpojetMeasItemRndnType

Return the DPOJET:MEAS<x>:RNDN:TYPe command.

Description
  • This command sets or queries the current RNDN measurement type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:TYPe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:TYPe {ARBITrary|REPEating}
- DPOJET:MEAS<x>:RNDN:TYPe?

windowlength property 

windowlength: DpojetMeasItemRndnWindowlength

Return the DPOJET:MEAS<x>:RNDN:WINDOwlength command.

Description
  • This command sets or queries the current RNDN window length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:WINDOwlength? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:WINDOwlength? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:WINDOwlength value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:WINDOwlength <NR3>
- DPOJET:MEAS<x>:RNDN:WINDOwlength?

DpojetMeasItemRndnAutodetectpattern

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:AUTODETECTpattern command.

Description
  • This command sets or queries the current pattern detection control plan.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:AUTODETECTpattern? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:AUTODETECTpattern? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:AUTODETECTpattern value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:AUTODETECTpattern {ON|OFF|1|0}
- DPOJET:MEAS<x>:RNDN:AUTODETECTpattern?

DpojetMeasItemRndnBer

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:BER command.

Description
  • This command sets or queries the RNDN Target BER value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:BER? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:BER value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:BER <NR3>
- DPOJET:MEAS<x>:RNDN:BER?

DpojetMeasItemRndnNcmode

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:NCMODe command.

Description
  • This command sets or queries the noise compensation mode.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:NCMODe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:NCMODe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:NCMODe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:NCMODe {1|0}
- DPOJET:MEAS<x>:RNDN:NCMODe?

DpojetMeasItemRndnPatlen

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:PATLen command.

Description
  • This command sets or queries the current RNDN pattern length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:PATLen? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:PATLen? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:PATLen value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:PATLen <NR3>
- DPOJET:MEAS<x>:RNDN:PATLen?

DpojetMeasItemRndnScopern

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:SCOPERN command.

Description
  • This command to sets or queries the scope noise value from the applicable measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:SCOPERN? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:SCOPERN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:SCOPERN value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:SCOPERN <NR3>
- DPOJET:MEAS<x>:RNDN:SCOPERN?

DpojetMeasItemRndnSncrefid

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:SNCREFID command.

Description
  • This command sets or queries the reference id which is used for fetching the noise value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:SNCREFID? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:SNCREFID? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:SNCREFID value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:SNCREFID <string>
- DPOJET:MEAS<x>:RNDN:SNCREFID?

DpojetMeasItemRndnType

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:TYPe command.

Description
  • This command sets or queries the current RNDN measurement type.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:TYPe value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:TYPe {ARBITrary|REPEating}
- DPOJET:MEAS<x>:RNDN:TYPe?

DpojetMeasItemRndnWindowlength

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:RNDN:WINDOwlength command.

Description
  • This command sets or queries the current RNDN window length.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:RNDN:WINDOwlength? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:RNDN:WINDOwlength? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:RNDN:WINDOwlength value command.
SCPI Syntax 
- DPOJET:MEAS<x>:RNDN:WINDOwlength <NR3>
- DPOJET:MEAS<x>:RNDN:WINDOwlength?

DpojetMeasItemSignaltype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:SIGNALType command.

Description
  • This command sets the signal type for various measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SIGNALType? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SIGNALType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SIGNALType value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SIGNALType {CLOCK|DATA|AUTO}
- DPOJET:MEAS<x>:SIGNALType?

DpojetMeasItemSource1

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:SOUrce1 command.

Description
  • This command sets or queries the Source1 value.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SOUrce1? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SOUrce1 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SOUrce1 {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|D0 — D15}
- DPOJET:MEAS<x>:SOUrce1?

DpojetMeasItemSource2

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:SOUrce2 command.

Description
  • This command sets or queries the Source2 value. May return NONE for single-source measurement. Source2 may be the second source used in dual-source measurements, or the clock source in others. In either case, it is always the same as the rightmost displayed source on the UI.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SOUrce2? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SOUrce2? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SOUrce2 value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SOUrce2 {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|D0 — D15}
- DPOJET:MEAS<x>:SOUrce2?

DpojetMeasItemSsc

Bases: SCPICmdRead

The DPOJET:MEAS<x>:SSC command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC? query and raise an AssertionError if the returned value does not match value.
Properties
  • .nominalfreq: The DPOJET:MEAS<x>:SSC:NOMinalfreq command tree.

nominalfreq property 

nominalfreq: DpojetMeasItemSscNominalfreq

Return the DPOJET:MEAS<x>:SSC:NOMinalfreq command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .auto: The DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO command.
  • .manual: The DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual command.
  • .selectiontype: The DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

DpojetMeasItemSscNominalfreq

Bases: SCPICmdRead

The DPOJET:MEAS<x>:SSC:NOMinalfreq command tree.

Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq? query and raise an AssertionError if the returned value does not match value.
Properties
  • .auto: The DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO command.
  • .manual: The DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual command.
  • .selectiontype: The DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

auto property 

auto: DpojetMeasItemSscNominalfreqAuto

Return the DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO command.

Description
  • This query-only command returns the automatically-calculated nominal frequency value for SSC configurations.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO?

manual property 

manual: DpojetMeasItemSscNominalfreqManual

Return the DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual command.

Description
  • This command sets or queries the user-defined nominal frequency value for SSC configurations.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual <NR3>
- DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual?

selectiontype property 

selectiontype: DpojetMeasItemSscNominalfreqSelectiontype

Return the DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

Description
  • This command sets or queries the Nominal frequency selection type for the SSC configurations.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANUAL}
- DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?

DpojetMeasItemSscNominalfreqAuto

Bases: SCPICmdRead

The DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO command.

Description
  • This query-only command returns the automatically-calculated nominal frequency value for SSC configurations.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:SSC:NOMinalfreq:AUTO?

DpojetMeasItemSscNominalfreqManual

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual command.

Description
  • This command sets or queries the user-defined nominal frequency value for SSC configurations.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual <NR3>
- DPOJET:MEAS<x>:SSC:NOMinalfreq:MANual?

DpojetMeasItemSscNominalfreqSelectiontype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype command.

Description
  • This command sets or queries the Nominal frequency selection type for the SSC configurations.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype value command.
SCPI Syntax 
- DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype {AUTO|MANUAL}
- DPOJET:MEAS<x>:SSC:NOMinalfreq:SELECTIONtype?

DpojetMeasItemTimedata

Bases: SCPICmdRead

The DPOJET:MEAS<x>:TIMEDATa command.

Description
  • This query-only command returns the measurement time data. It is similar to the curve query, where the output is in the format #, where is the number of bytes. For Example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: Time data is not available for all measurements. For Example: Scalar measurements.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:TIMEDATa? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:TIMEDATa? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:MEAS<x>:TIMEDATa?

DpojetMeasItemToedge

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MEAS<x>:TOEdge command.

Description
  • This command sets the TOEdge value for the measurement.
Usage
  • Using the .query() method will send the DPOJET:MEAS<x>:TOEdge? query.
  • Using the .verify(value) method will send the DPOJET:MEAS<x>:TOEdge? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MEAS<x>:TOEdge value command.
SCPI Syntax 
- DPOJET:MEAS<x>:TOEdge {SAMEas|OPPositeas}
- DPOJET:MEAS<x>:TOEdge?

DpojetMeasItemZoomevent

Bases: SCPICmdWrite

The DPOJET:MEAS<x>:ZOOMEVENT command.

Description
  • This command zooms into the waveform where a max/min value occurs in a measurement.
Usage
  • Using the .write(value) method will send the DPOJET:MEAS<x>:ZOOMEVENT value command.
SCPI Syntax 
- DPOJET:MEAS<x>:ZOOMEVENT {MAX|MIN}

DpojetMinbujui

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:MINBUJUI command.

Description
  • This command sets or queries the minimum number of UI for BUJ analysis.
Usage
  • Using the .query() method will send the DPOJET:MINBUJUI? query.
  • Using the .verify(value) method will send the DPOJET:MINBUJUI? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:MINBUJUI value command.
SCPI Syntax 
- DPOJET:MINBUJUI <NR3>
- DPOJET:MINBUJUI?

DpojetNoiseenabled

Bases: SCPICmdWrite

The DPOJET:NOISEENABLED command.

Description
  • This set-only command turns on or off the Noise measurements. Note: Configure
Usage
  • Using the .write(value) method will send the DPOJET:NOISEENABLED value command.
SCPI Syntax 
- DPOJET:NOISEENABLED {ON|OFF|1|0}

DpojetNummeas

Bases: SCPICmdRead

The DPOJET:NUMMeas command.

Description
  • This query-only command returns the current number of defined measurements.
Usage
  • Using the .query() method will send the DPOJET:NUMMeas? query.
  • Using the .verify(value) method will send the DPOJET:NUMMeas? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:NUMMeas?

DpojetNumplot

Bases: SCPICmdRead

The DPOJET:NUMPlot command.

Description
  • This query-only command returns the current number of plots added. If no plots are added, then it returns 0, else returns the total number of plots added between value 1 to 4.
Usage
  • Using the .query() method will send the DPOJET:NUMPlot? query.
  • Using the .verify(value) method will send the DPOJET:NUMPlot? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:NUMPlot?

DpojetOpticalunittype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:OPTICALUNITType command.

Description
  • This command sets or queries the current optical unit-type setting for DPOJET, either Watt, or dBm.
Usage
  • Using the .query() method will send the DPOJET:OPTICALUNITType? query.
  • Using the .verify(value) method will send the DPOJET:OPTICALUNITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:OPTICALUNITType value command.
SCPI Syntax 
- DPOJET:OPTICALUNITType {WATT|DBM}
- DPOJET:OPTICALUNITType?

DpojetPlotItem

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The DPOJET:PLOT<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>? query and raise an AssertionError if the returned value does not match value.
Properties
  • .bathtub: The DPOJET:PLOT<x>:BATHtub command tree.
  • .bercontour: The DPOJET:PLOT<x>:BERContour command tree.
  • .bereye: The DPOJET:PLOT<x>:BEREye command tree.
  • .compositejitterhist: The DPOJET:PLOT<x>:COMPOSITEJitterhist command tree.
  • .compositenoisehist: The DPOJET:PLOT<x>:COMPOSITENoisehist command tree.
  • .correlatedeye: The DPOJET:PLOT<x>:CORRELATEDEye command tree.
  • .currentuisacquired: The DPOJET:PLOT<x>:CURRENTUISACquired command.
  • .currentuisanalyzed: The DPOJET:PLOT<x>:CURRENTUISANalyzed command.
  • .data: The DPOJET:PLOT<x>:DATA command tree.
  • .exportraw: The DPOJET:PLOT<x>:EXPORTRaw command.
  • .eye: The DPOJET:PLOT<x>:EYE command tree.
  • .histogram: The DPOJET:PLOT<x>:HISTOgram command tree.
  • .noisebathtub: The DPOJET:PLOT<x>:NOISEBATHtub command tree.
  • .pdfeye: The DPOJET:PLOT<x>:PDFEye command tree.
  • .phasenoise: The DPOJET:PLOT<x>:PHASEnoise command tree.
  • .source: The DPOJET:PLOT<x>:SOUrce command.
  • .spectrum: The DPOJET:PLOT<x>:SPECtrum command tree.
  • .totaluisacquired: The DPOJET:PLOT<x>:TOTALUISAcquired command.
  • .totaluisanalyzed: The DPOJET:PLOT<x>:TOTALUISAnalyzed command.
  • .transfer: The DPOJET:PLOT<x>:TRANSfer command tree.
  • .trend: The DPOJET:PLOT<x>:TREND command tree.
  • .type: The DPOJET:PLOT<x>:TYPe command.
  • .vertbathtub: The DPOJET:PLOT<x>:VERTBATHtub command tree.
  • .xunits: The DPOJET:PLOT<x>:XUnits command.
  • .yunits: The DPOJET:PLOT<x>:YUnits command.

bathtub property 

bathtub: DpojetPlotItemBathtub

Return the DPOJET:PLOT<x>:BATHtub command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ber: The DPOJET:PLOT<x>:BATHtub:BER command.
  • .vertical: The DPOJET:PLOT<x>:BATHtub:VERTical command tree.
  • .xaxisunits: The DPOJET:PLOT<x>:BATHtub:XAXISUnits command.

bercontour property 

bercontour: DpojetPlotItemBercontour

Return the DPOJET:PLOT<x>:BERContour command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .alignment: The DPOJET:PLOT<x>:BERContour:ALIGNment command.
  • .ber1e12v: The DPOJET:PLOT<x>:BERContour:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:BERContour:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:BERContour:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:BERContour:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:BERContour:BER1E9V command.
  • .horizontal: The DPOJET:PLOT<x>:BERContour:HORizontal command tree.
  • .mask: The DPOJET:PLOT<x>:BERContour:MASK command.
  • .maskfile: The DPOJET:PLOT<x>:BERContour:MASKFile command.
  • .superimpose: The DPOJET:PLOT<x>:BERContour:SUPERImpose command.
  • .targetber: The DPOJET:PLOT<x>:BERContour:TARGETBER command.

bereye property 

bereye: DpojetPlotItemBereye

Return the DPOJET:PLOT<x>:BEREye command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ber1e12v: The DPOJET:PLOT<x>:BEREye:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:BEREye:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:BEREye:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:BEREye:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:BEREye:BER1E9V command.
  • .targetber: The DPOJET:PLOT<x>:BEREye:TARGETBER command.

compositejitterhist property 

compositejitterhist: DpojetPlotItemCompositejitterhist

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ddjdcd: The DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD command.
  • .numbins: The DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins command.
  • .pj: The DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ command.
  • .rjnpj: The DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ command.
  • .tj: The DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ command.
  • .vertical: The DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical command tree.

compositenoisehist property 

compositenoisehist: DpojetPlotItemCompositenoisehist

Return the DPOJET:PLOT<x>:COMPOSITENoisehist command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ddnone: The DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE command.
  • .ddnzero: The DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO command.
  • .horizontal: The DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal command tree.
  • .numbins: The DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins command.
  • .pn: The DPOJET:PLOT<x>:COMPOSITENoisehist:PN command.
  • .rnnpn: The DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN command.
  • .tn: The DPOJET:PLOT<x>:COMPOSITENoisehist:TN command.

correlatedeye property 

correlatedeye: DpojetPlotItemCorrelatedeye

Return the DPOJET:PLOT<x>:CORRELATEDEye command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ber1e12v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V command.
  • .eyeheight: The DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT command.
  • .eyewidth: The DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH command.
  • .targetber: The DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER command.

currentuisacquired property 

currentuisacquired: DpojetPlotItemCurrentuisacquired

Return the DPOJET:PLOT<x>:CURRENTUISACquired command.

Description
  • This command queries the current UIs acquired for eye diagram plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CURRENTUISACquired? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CURRENTUISACquired? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:CURRENTUISACquired?

currentuisanalyzed property 

currentuisanalyzed: DpojetPlotItemCurrentuisanalyzed

Return the DPOJET:PLOT<x>:CURRENTUISANalyzed command.

Description
  • This command queries the current UIs analyzed for Eye Diagram plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CURRENTUISANalyzed? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CURRENTUISANalyzed? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:CURRENTUISANalyzed?

data property 

data: DpojetPlotItemData

Return the DPOJET:PLOT<x>:DATA command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .xdata: The DPOJET:PLOT<x>:DATA:XDATa command.
  • .ydata: The DPOJET:PLOT<x>:DATA:YDATa command.

exportraw property 

exportraw: DpojetPlotItemExportraw

Return the DPOJET:PLOT<x>:EXPORTRaw command.

Description
  • This query command returns the raw Eye diagram 2d histogram data in binary format. This command is similar to curve query
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EXPORTRaw? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EXPORTRaw? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:EXPORTRaw?

eye property 

eye: DpojetPlotItemEye

Return the DPOJET:PLOT<x>:EYE command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .alignment: The DPOJET:PLOT<x>:EYE:ALIGNment command.
  • .eyeverticalscale: The DPOJET:PLOT<x>:EYE:EYEVerticalscale command.
  • .horizscale: The DPOJET:PLOT<x>:EYE:HORIZScale command.
  • .horizontal: The DPOJET:PLOT<x>:EYE:HORizontal command tree.
  • .interpolationfactor: The DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor command.
  • .interpolationtype: The DPOJET:PLOT<x>:EYE:INTERPolationtype command.
  • .maskfile: The DPOJET:PLOT<x>:EYE:MASKfile command.
  • .state: The DPOJET:PLOT<x>:EYE:STATE command.
  • .superimpose: The DPOJET:PLOT<x>:EYE:SUPERImpose command.
  • .verticalalignment: The DPOJET:PLOT<x>:EYE:VERTICALAlignment command.
  • .vertscale: The DPOJET:PLOT<x>:EYE:VERTScale command.
  • .vertical: The DPOJET:PLOT<x>:EYE:VERTical command tree.

histogram property 

histogram: DpojetPlotItemHistogram

Return the DPOJET:PLOT<x>:HISTOgram command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .autoset: The DPOJET:PLOT<x>:HISTOgram:AUTOset command.
  • .horizontal: The DPOJET:PLOT<x>:HISTOgram:HORizontal command tree.
  • .numbins: The DPOJET:PLOT<x>:HISTOgram:NUMBins command.
  • .vertical: The DPOJET:PLOT<x>:HISTOgram:VERTical command tree.

noisebathtub property 

noisebathtub: DpojetPlotItemNoisebathtub

Return the DPOJET:PLOT<x>:NOISEBATHtub command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:NOISEBATHtub? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:NOISEBATHtub? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .yaxisunits: The DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits command.

pdfeye property 

pdfeye: DpojetPlotItemPdfeye

Return the DPOJET:PLOT<x>:PDFEye command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ber1e12v: The DPOJET:PLOT<x>:PDFEye:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:PDFEye:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:PDFEye:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:PDFEye:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:PDFEye:BER1E9V command.
  • .targetber: The DPOJET:PLOT<x>:PDFEye:TARGETBER command.

phasenoise property 

phasenoise: DpojetPlotItemPhasenoise

Return the DPOJET:PLOT<x>:PHASEnoise command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PHASEnoise? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PHASEnoise? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .baseline: The DPOJET:PLOT<x>:PHASEnoise:BASEline command.
  • .smootheningfilter: The DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter command.

source property 

source: DpojetPlotItemSource

Return the DPOJET:PLOT<x>:SOUrce command.

Description
  • This query-only command returns the source measurement for the selected plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SOUrce? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SOUrce? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:SOUrce?

spectrum property 

spectrum: DpojetPlotItemSpectrum

Return the DPOJET:PLOT<x>:SPECtrum command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .base: The DPOJET:PLOT<x>:SPECtrum:BASE command.
  • .horizontal: The DPOJET:PLOT<x>:SPECtrum:HORizontal command tree.
  • .mode: The DPOJET:PLOT<x>:SPECtrum:MODE command.
  • .vertical: The DPOJET:PLOT<x>:SPECtrum:VERTical command tree.

totaluisacquired property 

totaluisacquired: DpojetPlotItemTotaluisacquired

Return the DPOJET:PLOT<x>:TOTALUISAcquired command.

Description
  • This command queries the total UIs acquired for Eye Diagram plot
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TOTALUISAcquired? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TOTALUISAcquired? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:TOTALUISAcquired?

totaluisanalyzed property 

totaluisanalyzed: DpojetPlotItemTotaluisanalyzed

Return the DPOJET:PLOT<x>:TOTALUISAnalyzed command.

Description
  • This command queries the total UIs analysed for Eye Diagram plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TOTALUISAnalyzed? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TOTALUISAnalyzed? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:TOTALUISAnalyzed?

transfer property 

transfer: DpojetPlotItemTransfer

Return the DPOJET:PLOT<x>:TRANSfer command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .denominator: The DPOJET:PLOT<x>:TRANSfer:DENominator command.
  • .horizontal: The DPOJET:PLOT<x>:TRANSfer:HORizontal command tree.
  • .mode: The DPOJET:PLOT<x>:TRANSfer:MODE command.
  • .numerator: The DPOJET:PLOT<x>:TRANSfer:NUMerator command.
  • .vertical: The DPOJET:PLOT<x>:TRANSfer:VERTical command tree.

trend property 

trend: DpojetPlotItemTrend

Return the DPOJET:PLOT<x>:TREND command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TREND? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TREND? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .type: The DPOJET:PLOT<x>:TREND:TYPe command.

type property 

type: DpojetPlotItemType

Return the DPOJET:PLOT<x>:TYPe command.

Description
  • This query-only command returns the current plot type for the selected plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TYPe? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:TYPe?

vertbathtub property 

vertbathtub: DpojetPlotItemVertbathtub

Return the DPOJET:PLOT<x>:VERTBATHtub command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .ber: The DPOJET:PLOT<x>:VERTBATHtub:BER command.
  • .horizontal: The DPOJET:PLOT<x>:VERTBATHtub:HORizontal command tree.
  • .yaxisunits: The DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits command.

xunits property 

xunits: DpojetPlotItemXunits

Return the DPOJET:PLOT<x>:XUnits command.

Description
  • This query-only command returns X units of the plot as a string. Note: Plot units depends on the measurement type.Click here to see the possible
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:XUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:XUnits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:XUnits?

yunits property 

yunits: DpojetPlotItemYunits

Return the DPOJET:PLOT<x>:YUnits command.

Description
  • This query-only command returns Y units of the plot as a string. Note: Plot units depends on the measurement type.Click here to see the possible
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:YUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:YUnits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:YUnits?

DpojetPlotItemBathtub

Bases: SCPICmdRead

The DPOJET:PLOT<x>:BATHtub command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ber: The DPOJET:PLOT<x>:BATHtub:BER command.
  • .vertical: The DPOJET:PLOT<x>:BATHtub:VERTical command tree.
  • .xaxisunits: The DPOJET:PLOT<x>:BATHtub:XAXISUnits command.

ber property 

ber: DpojetPlotItemBathtubBer

Return the DPOJET:PLOT<x>:BATHtub:BER command.

Description
  • This command sets or queries the bathtub BER value. Note: Undefined for nonbathtub plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:BER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BATHtub:BER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BATHtub:BER <NR3>
- DPOJET:PLOT<x>:BATHtub:BER?

vertical property 

vertical: DpojetPlotItemBathtubVertical

Return the DPOJET:PLOT<x>:BATHtub:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:VERTical? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:BATHtub:VERTical:SCALE command.

xaxisunits property 

xaxisunits: DpojetPlotItemBathtubXaxisunits

Return the DPOJET:PLOT<x>:BATHtub:XAXISUnits command.

Description
  • This command sets or queries the X-Axis Units of Bathtub.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:XAXISUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:XAXISUnits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BATHtub:XAXISUnits value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BATHtub:XAXISUnits { UNITIntervals|SECOnds }
- DPOJET:PLOT<x>:BATHtub:XAXISUnits?

DpojetPlotItemBathtubBer

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BATHtub:BER command.

Description
  • This command sets or queries the bathtub BER value. Note: Undefined for nonbathtub plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:BER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BATHtub:BER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BATHtub:BER <NR3>
- DPOJET:PLOT<x>:BATHtub:BER?

DpojetPlotItemBathtubVertical

Bases: SCPICmdRead

The DPOJET:PLOT<x>:BATHtub:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:VERTical? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:BATHtub:VERTical:SCALE command.

scale property 

scale: DpojetPlotItemBathtubVerticalScale

Return the DPOJET:PLOT<x>:BATHtub:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for nonbathtub plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BATHtub:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BATHtub:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:BATHtub:VERTical:SCALE?

DpojetPlotItemBathtubVerticalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BATHtub:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for nonbathtub plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BATHtub:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BATHtub:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:BATHtub:VERTical:SCALE?

DpojetPlotItemBathtubXaxisunits

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BATHtub:XAXISUnits command.

Description
  • This command sets or queries the X-Axis Units of Bathtub.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BATHtub:XAXISUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BATHtub:XAXISUnits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BATHtub:XAXISUnits value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BATHtub:XAXISUnits { UNITIntervals|SECOnds }
- DPOJET:PLOT<x>:BATHtub:XAXISUnits?

DpojetPlotItemBercontour

Bases: SCPICmdRead

The DPOJET:PLOT<x>:BERContour command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour? query and raise an AssertionError if the returned value does not match value.
Properties
  • .alignment: The DPOJET:PLOT<x>:BERContour:ALIGNment command.
  • .ber1e12v: The DPOJET:PLOT<x>:BERContour:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:BERContour:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:BERContour:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:BERContour:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:BERContour:BER1E9V command.
  • .horizontal: The DPOJET:PLOT<x>:BERContour:HORizontal command tree.
  • .mask: The DPOJET:PLOT<x>:BERContour:MASK command.
  • .maskfile: The DPOJET:PLOT<x>:BERContour:MASKFile command.
  • .superimpose: The DPOJET:PLOT<x>:BERContour:SUPERImpose command.
  • .targetber: The DPOJET:PLOT<x>:BERContour:TARGETBER command.

alignment property 

alignment: DpojetPlotItemBercontourAlignment

Return the DPOJET:PLOT<x>:BERContour:ALIGNment command.

Description
  • This command sets or queries the BER contour alighment.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:ALIGNment? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:ALIGNment? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:ALIGNment value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:ALIGNment {AUTO|LEFT|CENter}
- DPOJET:PLOT<x>:BERContour:ALIGNment?

ber1e12v property 

ber1e12v: DpojetPlotItemBercontourBer1e12v

Return the DPOJET:PLOT<x>:BERContour:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E12V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E12V?

ber1e15v property 

ber1e15v: DpojetPlotItemBercontourBer1e15v

Return the DPOJET:PLOT<x>:BERContour:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E15V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E15V?

ber1e18v property 

ber1e18v: DpojetPlotItemBercontourBer1e18v

Return the DPOJET:PLOT<x>:BERContour:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E18V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E18V?

ber1e6v property 

ber1e6v: DpojetPlotItemBercontourBer1e6v

Return the DPOJET:PLOT<x>:BERContour:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E6V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E6V?

ber1e9v property 

ber1e9v: DpojetPlotItemBercontourBer1e9v

Return the DPOJET:PLOT<x>:BERContour:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E9V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E9V?

horizontal property 

horizontal: DpojetPlotItemBercontourHorizontal

Return the DPOJET:PLOT<x>:BERContour:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .autoscale: The DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale command.
  • .resolution: The DPOJET:PLOT<x>:BERContour:HORizontal:RESolution command.

mask property 

mask: DpojetPlotItemBercontourMask

Return the DPOJET:PLOT<x>:BERContour:MASK command.

Description
  • This command sets or queries the eye state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:MASK? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:MASK? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:MASK value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:MASK {1|0}
- DPOJET:PLOT<x>:BERContour:MASK?

maskfile property 

maskfile: DpojetPlotItemBercontourMaskfile

Return the DPOJET:PLOT<x>:BERContour:MASKFile command.

Description
  • This command sets or queries the mask file.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:MASKFile? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:MASKFile? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:MASKFile value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:MASKFile <string>
- DPOJET:PLOT<x>:BERContour:MASKFile?

superimpose property 

superimpose: DpojetPlotItemBercontourSuperimpose

Return the DPOJET:PLOT<x>:BERContour:SUPERImpose command.

Description
  • This command sets or queries whether superimposed eyes are generated in eye diagrams.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:SUPERImpose? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:SUPERImpose? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:SUPERImpose value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:SUPERImpose {1|0}
- DPOJET:PLOT<x>:BERContour:SUPERImpose?

targetber property 

targetber: DpojetPlotItemBercontourTargetber

Return the DPOJET:PLOT<x>:BERContour:TARGETBER command.

Description
  • This command sets or queries the Target BER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:TARGETBER {1|0}
- DPOJET:PLOT<x>:BERContour:TARGETBER?

DpojetPlotItemBercontourAlignment

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:ALIGNment command.

Description
  • This command sets or queries the BER contour alighment.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:ALIGNment? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:ALIGNment? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:ALIGNment value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:ALIGNment {AUTO|LEFT|CENter}
- DPOJET:PLOT<x>:BERContour:ALIGNment?

DpojetPlotItemBercontourBer1e12v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E12V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E12V?

DpojetPlotItemBercontourBer1e15v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E15V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E15V?

DpojetPlotItemBercontourBer1e18v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E18V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E18V?

DpojetPlotItemBercontourBer1e6v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E6V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E6V?

DpojetPlotItemBercontourBer1e9v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:BER1E9V {1|0}
- DPOJET:PLOT<x>:BERContour:BER1E9V?

DpojetPlotItemBercontourHorizontal

Bases: SCPICmdRead

The DPOJET:PLOT<x>:BERContour:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .autoscale: The DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale command.
  • .resolution: The DPOJET:PLOT<x>:BERContour:HORizontal:RESolution command.

autoscale property 

autoscale: DpojetPlotItemBercontourHorizontalAutoscale

Return the DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale command.

Description
  • This command sets or queries the horizontal auto scale setting.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale?

resolution property 

resolution: DpojetPlotItemBercontourHorizontalResolution

Return the DPOJET:PLOT<x>:BERContour:HORizontal:RESolution command.

Description
  • This command sets or queries the Horizontal Eye resolution.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:HORizontal:RESolution? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:RESolution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:RESolution value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:HORizontal:RESolution <NR3>
- DPOJET:PLOT<x>:BERContour:HORizontal:RESolution?

DpojetPlotItemBercontourHorizontalAutoscale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale command.

Description
  • This command sets or queries the horizontal auto scale setting.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:BERContour:HORizontal:AUTOscale?

DpojetPlotItemBercontourHorizontalResolution

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:HORizontal:RESolution command.

Description
  • This command sets or queries the Horizontal Eye resolution.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:HORizontal:RESolution? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:RESolution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:HORizontal:RESolution value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:HORizontal:RESolution <NR3>
- DPOJET:PLOT<x>:BERContour:HORizontal:RESolution?

DpojetPlotItemBercontourMask

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:MASK command.

Description
  • This command sets or queries the eye state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:MASK? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:MASK? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:MASK value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:MASK {1|0}
- DPOJET:PLOT<x>:BERContour:MASK?

DpojetPlotItemBercontourMaskfile

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:MASKFile command.

Description
  • This command sets or queries the mask file.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:MASKFile? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:MASKFile? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:MASKFile value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:MASKFile <string>
- DPOJET:PLOT<x>:BERContour:MASKFile?

DpojetPlotItemBercontourSuperimpose

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:SUPERImpose command.

Description
  • This command sets or queries whether superimposed eyes are generated in eye diagrams.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:SUPERImpose? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:SUPERImpose? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:SUPERImpose value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:SUPERImpose {1|0}
- DPOJET:PLOT<x>:BERContour:SUPERImpose?

DpojetPlotItemBercontourTargetber

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BERContour:TARGETBER command.

Description
  • This command sets or queries the Target BER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BERContour:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BERContour:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BERContour:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BERContour:TARGETBER {1|0}
- DPOJET:PLOT<x>:BERContour:TARGETBER?

DpojetPlotItemBereye

Bases: SCPICmdRead

The DPOJET:PLOT<x>:BEREye command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ber1e12v: The DPOJET:PLOT<x>:BEREye:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:BEREye:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:BEREye:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:BEREye:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:BEREye:BER1E9V command.
  • .targetber: The DPOJET:PLOT<x>:BEREye:TARGETBER command.

ber1e12v property 

ber1e12v: DpojetPlotItemBereyeBer1e12v

Return the DPOJET:PLOT<x>:BEREye:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E12V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E12V?

ber1e15v property 

ber1e15v: DpojetPlotItemBereyeBer1e15v

Return the DPOJET:PLOT<x>:BEREye:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E15V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E15V?

ber1e18v property 

ber1e18v: DpojetPlotItemBereyeBer1e18v

Return the DPOJET:PLOT<x>:BEREye:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E18V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E18V?

ber1e6v property 

ber1e6v: DpojetPlotItemBereyeBer1e6v

Return the DPOJET:PLOT<x>:BEREye:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E6V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E6V?

ber1e9v property 

ber1e9v: DpojetPlotItemBereyeBer1e9v

Return the DPOJET:PLOT<x>:BEREye:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E9V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E9V?

targetber property 

targetber: DpojetPlotItemBereyeTargetber

Return the DPOJET:PLOT<x>:BEREye:TARGETBER command.

Description
  • This command sets or queries the TARGETBER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:TARGETBER {1|0}
- DPOJET:PLOT<x>:BEREye:TARGETBER?

DpojetPlotItemBereyeBer1e12v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BEREye:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E12V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E12V?

DpojetPlotItemBereyeBer1e15v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BEREye:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E15V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E15V?

DpojetPlotItemBereyeBer1e18v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BEREye:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E18V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E18V?

DpojetPlotItemBereyeBer1e6v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BEREye:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E6V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E6V?

DpojetPlotItemBereyeBer1e9v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BEREye:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:BER1E9V {1|0}
- DPOJET:PLOT<x>:BEREye:BER1E9V?

DpojetPlotItemBereyeTargetber

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:BEREye:TARGETBER command.

Description
  • This command sets or queries the TARGETBER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:BEREye:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:BEREye:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:BEREye:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:BEREye:TARGETBER {1|0}
- DPOJET:PLOT<x>:BEREye:TARGETBER?

DpojetPlotItemCompositejitterhist

Bases: SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ddjdcd: The DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD command.
  • .numbins: The DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins command.
  • .pj: The DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ command.
  • .rjnpj: The DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ command.
  • .tj: The DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ command.
  • .vertical: The DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical command tree.

ddjdcd property 

ddjdcd: DpojetPlotItemCompositejitterhistDdjdcd

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD command.

Description
  • This command sets or queries the DDJ+DCD Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD?

numbins property 

numbins: DpojetPlotItemCompositejitterhistNumbins

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins command.

Description
  • This command sets or queries the current composite jitter histogram resolution. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins?

pj property 

pj: DpojetPlotItemCompositejitterhistPj

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ command.

Description
  • This command sets or queries the PJ Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ?

rjnpj property 

rjnpj: DpojetPlotItemCompositejitterhistRjnpj

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ command.

Description
  • This command sets or queries the RJ+NPJ Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ?

tj property 

tj: DpojetPlotItemCompositejitterhistTj

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ command.

Description
  • This command sets or queries the TJ Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ?

vertical property 

vertical: DpojetPlotItemCompositejitterhistVertical

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE command.

DpojetPlotItemCompositejitterhistDdjdcd

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD command.

Description
  • This command sets or queries the DDJ+DCD Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:DDJDCD?

DpojetPlotItemCompositejitterhistNumbins

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins command.

Description
  • This command sets or queries the current composite jitter histogram resolution. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:NUMBins?

DpojetPlotItemCompositejitterhistPj

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ command.

Description
  • This command sets or queries the PJ Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:PJ?

DpojetPlotItemCompositejitterhistRjnpj

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ command.

Description
  • This command sets or queries the RJ+NPJ Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:RJNPJ?

DpojetPlotItemCompositejitterhistTj

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ command.

Description
  • This command sets or queries the TJ Jitter component settings. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ {1|0}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:TJ?

DpojetPlotItemCompositejitterhistVertical

Bases: SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE command.

scale property 

scale: DpojetPlotItemCompositejitterhistVerticalScale

Return the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE?

DpojetPlotItemCompositejitterhistVerticalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for non-composite jitter histogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:COMPOSITEJitterhist:VERTical:SCALE?

DpojetPlotItemCompositenoisehist

Bases: SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ddnone: The DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE command.
  • .ddnzero: The DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO command.
  • .horizontal: The DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal command tree.
  • .numbins: The DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins command.
  • .pn: The DPOJET:PLOT<x>:COMPOSITENoisehist:PN command.
  • .rnnpn: The DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN command.
  • .tn: The DPOJET:PLOT<x>:COMPOSITENoisehist:TN command.

ddnone property 

ddnone: DpojetPlotItemCompositenoisehistDdnone

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE command.

Description
  • This command sets or queries the DDN(1) Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE?

ddnzero property 

ddnzero: DpojetPlotItemCompositenoisehistDdnzero

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO command.

Description
  • This command sets or queries the DDN(0) Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO?

horizontal property 

horizontal: DpojetPlotItemCompositenoisehistHorizontal

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE command.

numbins property 

numbins: DpojetPlotItemCompositenoisehistNumbins

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins command.

Description
  • This command sets or queries the current composite noise histogram resolution.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins { TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins?

pn property 

pn: DpojetPlotItemCompositenoisehistPn

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:PN command.

Description
  • This command sets or queries the PN Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:PN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:PN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:PN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:PN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:PN?

rnnpn property 

rnnpn: DpojetPlotItemCompositenoisehistRnnpn

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN command.

Description
  • This command sets or queries the RN+NPN Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN?

tn property 

tn: DpojetPlotItemCompositenoisehistTn

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:TN command.

Description
  • This command sets or queries the TN Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:TN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:TN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:TN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:TN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:TN?

DpojetPlotItemCompositenoisehistDdnone

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE command.

Description
  • This command sets or queries the DDN(1) Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNONE?

DpojetPlotItemCompositenoisehistDdnzero

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO command.

Description
  • This command sets or queries the DDN(0) Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:DDNZERO?

DpojetPlotItemCompositenoisehistHorizontal

Bases: SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE command.

scale property 

scale: DpojetPlotItemCompositenoisehistHorizontalScale

Return the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE command.

Description
  • This command sets or queries the Horizontal scale setting for applicable plots, either Linear or Log.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE?

DpojetPlotItemCompositenoisehistHorizontalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE command.

Description
  • This command sets or queries the Horizontal scale setting for applicable plots, either Linear or Log.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:COMPOSITENoisehist:HORizontal:SCALE?

DpojetPlotItemCompositenoisehistNumbins

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins command.

Description
  • This command sets or queries the current composite noise histogram resolution.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins { TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:COMPOSITENoisehist:NUMBins?

DpojetPlotItemCompositenoisehistPn

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:PN command.

Description
  • This command sets or queries the PN Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:PN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:PN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:PN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:PN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:PN?

DpojetPlotItemCompositenoisehistRnnpn

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN command.

Description
  • This command sets or queries the RN+NPN Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:RNNPN?

DpojetPlotItemCompositenoisehistTn

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:COMPOSITENoisehist:TN command.

Description
  • This command sets or queries the TN Noise component settings.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:TN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:TN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:COMPOSITENoisehist:TN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:COMPOSITENoisehist:TN {1|0}
- DPOJET:PLOT<x>:COMPOSITENoisehist:TN?

DpojetPlotItemCorrelatedeye

Bases: SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ber1e12v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V command.
  • .eyeheight: The DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT command.
  • .eyewidth: The DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH command.
  • .targetber: The DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER command.

ber1e12v property 

ber1e12v: DpojetPlotItemCorrelatedeyeBer1e12v

Return the DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V?

ber1e15v property 

ber1e15v: DpojetPlotItemCorrelatedeyeBer1e15v

Return the DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V?

ber1e18v property 

ber1e18v: DpojetPlotItemCorrelatedeyeBer1e18v

Return the DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V?

ber1e6v property 

ber1e6v: DpojetPlotItemCorrelatedeyeBer1e6v

Return the DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V?

ber1e9v property 

ber1e9v: DpojetPlotItemCorrelatedeyeBer1e9v

Return the DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V?

eyeheight property 

eyeheight: DpojetPlotItemCorrelatedeyeEyeheight

Return the DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT command.

Description
  • This command sets or queries the eye height of correlated eye diagram.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT <NR2>
- DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT?

eyewidth property 

eyewidth: DpojetPlotItemCorrelatedeyeEyewidth

Return the DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH command.

Description
  • This command sets or queries the eye width of correlated eye diagram.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH <NR2>
- DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH?

targetber property 

targetber: DpojetPlotItemCorrelatedeyeTargetber

Return the DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER command.

Description
  • This command sets or queries the TARGETBER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER?

DpojetPlotItemCorrelatedeyeBer1e12v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E12V?

DpojetPlotItemCorrelatedeyeBer1e15v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E15V?

DpojetPlotItemCorrelatedeyeBer1e18v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E18V?

DpojetPlotItemCorrelatedeyeBer1e6v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E6V?

DpojetPlotItemCorrelatedeyeBer1e9v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:BER1E9V?

DpojetPlotItemCorrelatedeyeEyeheight

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT command.

Description
  • This command sets or queries the eye height of correlated eye diagram.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT <NR2>
- DPOJET:PLOT<x>:CORRELATEDEye:EYEHEIGHT?

DpojetPlotItemCorrelatedeyeEyewidth

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH command.

Description
  • This command sets or queries the eye width of correlated eye diagram.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH <NR2>
- DPOJET:PLOT<x>:CORRELATEDEye:EYEWIDTH?

DpojetPlotItemCorrelatedeyeTargetber

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER command.

Description
  • This command sets or queries the TARGETBER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER {1|0}
- DPOJET:PLOT<x>:CORRELATEDEye:TARGETBER?

DpojetPlotItemCurrentuisacquired

Bases: SCPICmdRead

The DPOJET:PLOT<x>:CURRENTUISACquired command.

Description
  • This command queries the current UIs acquired for eye diagram plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CURRENTUISACquired? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CURRENTUISACquired? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:CURRENTUISACquired?

DpojetPlotItemCurrentuisanalyzed

Bases: SCPICmdRead

The DPOJET:PLOT<x>:CURRENTUISANalyzed command.

Description
  • This command queries the current UIs analyzed for Eye Diagram plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:CURRENTUISANalyzed? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:CURRENTUISANalyzed? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:CURRENTUISANalyzed?

DpojetPlotItemData

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA? query and raise an AssertionError if the returned value does not match value.
Properties
  • .xdata: The DPOJET:PLOT<x>:DATA:XDATa command.
  • .ydata: The DPOJET:PLOT<x>:DATA:YDATa command.

xdata property 

xdata: DpojetPlotItemDataXdata

Return the DPOJET:PLOT<x>:DATA:XDATa command.

Description
  • This command returns the plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: This command does not support plots such as the Eye Diagram Height plot, Waveform Plot and Eye diagram with mask hits.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa?
Sub-properties
  • .ddjdcd: The DPOJET:PLOT<x>:DATA:XDATa:DDJDCD command.
  • .ddnone: The DPOJET:PLOT<x>:DATA:XDATa:DDNONE command.
  • .ddnzero: The DPOJET:PLOT<x>:DATA:XDATa:DDNZERO command.
  • .pj: The DPOJET:PLOT<x>:DATA:XDATa:PJ command.
  • .pn: The DPOJET:PLOT<x>:DATA:XDATa:PN command.
  • .rjbuj: The DPOJET:PLOT<x>:DATA:XDATa:RJBUJ command.
  • .rnnpn: The DPOJET:PLOT<x>:DATA:XDATa:RNNPN command.
  • .tj: The DPOJET:PLOT<x>:DATA:XDATa:TJ command.
  • .tn: The DPOJET:PLOT<x>:DATA:XDATa:TN command.

ydata property 

ydata: DpojetPlotItemDataYdata

Return the DPOJET:PLOT<x>:DATA:YDATa command.

Description
  • This command returns the plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: This command does not support plots such as the Eye Diagram Height plot, Waveform Plot and Eye diagram with mask hits.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa?
Sub-properties
  • .ddjdcd: The DPOJET:PLOT<x>:DATA:YDATa:DDJDCD command.
  • .ddnone: The DPOJET:PLOT<x>:DATA:YDATa:DDNONE command.
  • .ddnzero: The DPOJET:PLOT<x>:DATA:YDATa:DDNZERO command.
  • .pj: The DPOJET:PLOT<x>:DATA:YDATa:PJ command.
  • .pn: The DPOJET:PLOT<x>:DATA:YDATa:PN command.
  • .rjbuj: The DPOJET:PLOT<x>:DATA:YDATa:RJBUJ command.
  • .rnnpn: The DPOJET:PLOT<x>:DATA:YDATa:RNNPN command.
  • .tj: The DPOJET:PLOT<x>:DATA:YDATa:TJ command.
  • .tn: The DPOJET:PLOT<x>:DATA:YDATa:TN command.

DpojetPlotItemDataXdata

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa command.

Description
  • This command returns the plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: This command does not support plots such as the Eye Diagram Height plot, Waveform Plot and Eye diagram with mask hits.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa?
Properties
  • .ddjdcd: The DPOJET:PLOT<x>:DATA:XDATa:DDJDCD command.
  • .ddnone: The DPOJET:PLOT<x>:DATA:XDATa:DDNONE command.
  • .ddnzero: The DPOJET:PLOT<x>:DATA:XDATa:DDNZERO command.
  • .pj: The DPOJET:PLOT<x>:DATA:XDATa:PJ command.
  • .pn: The DPOJET:PLOT<x>:DATA:XDATa:PN command.
  • .rjbuj: The DPOJET:PLOT<x>:DATA:XDATa:RJBUJ command.
  • .rnnpn: The DPOJET:PLOT<x>:DATA:XDATa:RNNPN command.
  • .tj: The DPOJET:PLOT<x>:DATA:XDATa:TJ command.
  • .tn: The DPOJET:PLOT<x>:DATA:XDATa:TN command.

ddjdcd property 

ddjdcd: DpojetPlotItemDataXdataDdjdcd

Return the DPOJET:PLOT<x>:DATA:XDATa:DDJDCD command.

Description
  • This command returns the DDJ+DCD plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:DDJDCD? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:DDJDCD? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:DDJDCD?

ddnone property 

ddnone: DpojetPlotItemDataXdataDdnone

Return the DPOJET:PLOT<x>:DATA:XDATa:DDNONE command.

Description
  • This command returns the DDNONE plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNONE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNONE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:DDNONE?

ddnzero property 

ddnzero: DpojetPlotItemDataXdataDdnzero

Return the DPOJET:PLOT<x>:DATA:XDATa:DDNZERO command.

Description
  • This command returns the DDNZERO plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNZERO? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNZERO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:DDNZERO?

pj property 

pj: DpojetPlotItemDataXdataPj

Return the DPOJET:PLOT<x>:DATA:XDATa:PJ command.

Description
  • This command returns the PJ plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:PJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:PJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:PJ?

pn property 

pn: DpojetPlotItemDataXdataPn

Return the DPOJET:PLOT<x>:DATA:XDATa:PN command.

Description
  • This command returns the PN plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:PN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:PN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:PN?

rjbuj property 

rjbuj: DpojetPlotItemDataXdataRjbuj

Return the DPOJET:PLOT<x>:DATA:XDATa:RJBUJ command.

Description
  • This command returns the RJ+BUJ plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:RJBUJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:RJBUJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:RJBUJ?

rnnpn property 

rnnpn: DpojetPlotItemDataXdataRnnpn

Return the DPOJET:PLOT<x>:DATA:XDATa:RNNPN command.

Description
  • This command returns the RNNPN plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:RNNPN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:RNNPN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:RNNPN?

tj property 

tj: DpojetPlotItemDataXdataTj

Return the DPOJET:PLOT<x>:DATA:XDATa:TJ command.

Description
  • This command returns the TJ plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:TJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:TJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:TJ?

tn property 

tn: DpojetPlotItemDataXdataTn

Return the DPOJET:PLOT<x>:DATA:XDATa:TN command.

Description
  • This command returns the TN plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:TN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:TN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:TN?

DpojetPlotItemDataXdataDdjdcd

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:DDJDCD command.

Description
  • This command returns the DDJ+DCD plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:DDJDCD? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:DDJDCD? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:DDJDCD?

DpojetPlotItemDataXdataDdnone

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:DDNONE command.

Description
  • This command returns the DDNONE plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNONE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNONE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:DDNONE?

DpojetPlotItemDataXdataDdnzero

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:DDNZERO command.

Description
  • This command returns the DDNZERO plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNZERO? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:DDNZERO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:DDNZERO?

DpojetPlotItemDataXdataPj

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:PJ command.

Description
  • This command returns the PJ plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:PJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:PJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:PJ?

DpojetPlotItemDataXdataPn

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:PN command.

Description
  • This command returns the PN plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:PN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:PN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:PN?

DpojetPlotItemDataXdataRjbuj

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:RJBUJ command.

Description
  • This command returns the RJ+BUJ plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:RJBUJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:RJBUJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:RJBUJ?

DpojetPlotItemDataXdataRnnpn

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:RNNPN command.

Description
  • This command returns the RNNPN plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:RNNPN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:RNNPN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:RNNPN?

DpojetPlotItemDataXdataTj

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:TJ command.

Description
  • This command returns the TJ plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:TJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:TJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:TJ?

DpojetPlotItemDataXdataTn

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:XDATa:TN command.

Description
  • This command returns the TN plot X data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:XDATa:TN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:XDATa:TN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:XDATa:TN?

DpojetPlotItemDataYdata

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa command.

Description
  • This command returns the plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data. Note: This command does not support plots such as the Eye Diagram Height plot, Waveform Plot and Eye diagram with mask hits.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa?
Properties
  • .ddjdcd: The DPOJET:PLOT<x>:DATA:YDATa:DDJDCD command.
  • .ddnone: The DPOJET:PLOT<x>:DATA:YDATa:DDNONE command.
  • .ddnzero: The DPOJET:PLOT<x>:DATA:YDATa:DDNZERO command.
  • .pj: The DPOJET:PLOT<x>:DATA:YDATa:PJ command.
  • .pn: The DPOJET:PLOT<x>:DATA:YDATa:PN command.
  • .rjbuj: The DPOJET:PLOT<x>:DATA:YDATa:RJBUJ command.
  • .rnnpn: The DPOJET:PLOT<x>:DATA:YDATa:RNNPN command.
  • .tj: The DPOJET:PLOT<x>:DATA:YDATa:TJ command.
  • .tn: The DPOJET:PLOT<x>:DATA:YDATa:TN command.

ddjdcd property 

ddjdcd: DpojetPlotItemDataYdataDdjdcd

Return the DPOJET:PLOT<x>:DATA:YDATa:DDJDCD command.

Description
  • This command returns the DDJ+DCD plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:DDJDCD? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:DDJDCD? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:DDJDCD?

ddnone property 

ddnone: DpojetPlotItemDataYdataDdnone

Return the DPOJET:PLOT<x>:DATA:YDATa:DDNONE command.

Description
  • This command returns the DDNONE plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNONE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNONE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:DDNONE?

ddnzero property 

ddnzero: DpojetPlotItemDataYdataDdnzero

Return the DPOJET:PLOT<x>:DATA:YDATa:DDNZERO command.

Description
  • This command returns the DDNZERO plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNZERO? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNZERO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:DDNZERO?

pj property 

pj: DpojetPlotItemDataYdataPj

Return the DPOJET:PLOT<x>:DATA:YDATa:PJ command.

Description
  • This command returns the PJ plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:PJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:PJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:PJ?

pn property 

pn: DpojetPlotItemDataYdataPn

Return the DPOJET:PLOT<x>:DATA:YDATa:PN command.

Description
  • This command returns the PN plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:PN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:PN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:PN?

rjbuj property 

rjbuj: DpojetPlotItemDataYdataRjbuj

Return the DPOJET:PLOT<x>:DATA:YDATa:RJBUJ command.

Description
  • This command returns the RJ+BUJ plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:RJBUJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:RJBUJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:RJBUJ?

rnnpn property 

rnnpn: DpojetPlotItemDataYdataRnnpn

Return the DPOJET:PLOT<x>:DATA:YDATa:RNNPN command.

Description
  • This command returns the RNNPN plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:RNNPN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:RNNPN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:RNNPN?

tj property 

tj: DpojetPlotItemDataYdataTj

Return the DPOJET:PLOT<x>:DATA:YDATa:TJ command.

Description
  • This command returns the TJ plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:TJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:TJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:TJ?

tn property 

tn: DpojetPlotItemDataYdataTn

Return the DPOJET:PLOT<x>:DATA:YDATa:TN command.

Description
  • This command returns the TN plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:TN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:TN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:TN?

DpojetPlotItemDataYdataDdjdcd

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:DDJDCD command.

Description
  • This command returns the DDJ+DCD plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:DDJDCD? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:DDJDCD? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:DDJDCD?

DpojetPlotItemDataYdataDdnone

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:DDNONE command.

Description
  • This command returns the DDNONE plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNONE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNONE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:DDNONE?

DpojetPlotItemDataYdataDdnzero

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:DDNZERO command.

Description
  • This command returns the DDNZERO plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNZERO? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:DDNZERO? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:DDNZERO?

DpojetPlotItemDataYdataPj

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:PJ command.

Description
  • This command returns the PJ plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:PJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:PJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:PJ?

DpojetPlotItemDataYdataPn

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:PN command.

Description
  • This command returns the PN plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:PN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:PN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:PN?

DpojetPlotItemDataYdataRjbuj

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:RJBUJ command.

Description
  • This command returns the RJ+BUJ plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:RJBUJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:RJBUJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:RJBUJ?

DpojetPlotItemDataYdataRnnpn

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:RNNPN command.

Description
  • This command returns the RNNPN plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:RNNPN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:RNNPN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:RNNPN?

DpojetPlotItemDataYdataTj

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:TJ command.

Description
  • This command returns the TJ plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:TJ? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:TJ? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:TJ?

DpojetPlotItemDataYdataTn

Bases: SCPICmdRead

The DPOJET:PLOT<x>:DATA:YDATa:TN command.

Description
  • This command returns the TN plot Y data values. This command is similar to the curve query, where the output is in the format #, where is the number of bytes. For example: If =500, =3 is hexadecimal format. The letters A-F denote the number of y bytes between 10 and 15 digits. is the number of bytes to transfer. is curve data. is a single-byte new line character at the end of the data.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:DATA:YDATa:TN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:DATA:YDATa:TN? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:DATA:YDATa:TN?

DpojetPlotItemExportraw

Bases: SCPICmdRead

The DPOJET:PLOT<x>:EXPORTRaw command.

Description
  • This query command returns the raw Eye diagram 2d histogram data in binary format. This command is similar to curve query
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EXPORTRaw? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EXPORTRaw? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:EXPORTRaw?

DpojetPlotItemEye

Bases: SCPICmdRead

The DPOJET:PLOT<x>:EYE command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE? query and raise an AssertionError if the returned value does not match value.
Properties
  • .alignment: The DPOJET:PLOT<x>:EYE:ALIGNment command.
  • .eyeverticalscale: The DPOJET:PLOT<x>:EYE:EYEVerticalscale command.
  • .horizscale: The DPOJET:PLOT<x>:EYE:HORIZScale command.
  • .horizontal: The DPOJET:PLOT<x>:EYE:HORizontal command tree.
  • .interpolationfactor: The DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor command.
  • .interpolationtype: The DPOJET:PLOT<x>:EYE:INTERPolationtype command.
  • .maskfile: The DPOJET:PLOT<x>:EYE:MASKfile command.
  • .state: The DPOJET:PLOT<x>:EYE:STATE command.
  • .superimpose: The DPOJET:PLOT<x>:EYE:SUPERImpose command.
  • .verticalalignment: The DPOJET:PLOT<x>:EYE:VERTICALAlignment command.
  • .vertscale: The DPOJET:PLOT<x>:EYE:VERTScale command.
  • .vertical: The DPOJET:PLOT<x>:EYE:VERTical command tree.

alignment property 

alignment: DpojetPlotItemEyeAlignment

Return the DPOJET:PLOT<x>:EYE:ALIGNment command.

Description
  • This command sets or queries eye alignment state for eye plots. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:ALIGNment? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:ALIGNment? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:ALIGNment value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:ALIGNment {AUTO|LEFT|CENter}
- DPOJET:PLOT<x>:EYE:ALIGNment?

eyeverticalscale property 

eyeverticalscale: DpojetPlotItemEyeEyeverticalscale

Return the DPOJET:PLOT<x>:EYE:EYEVerticalscale command.

Description
  • This command sets or queries eye diagram vertical scale when superimpose reference clock eye is checked.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:EYEVerticalscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:EYEVerticalscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:EYEVerticalscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:EYEVerticalscale {SCALETOData, SCALETORefclk}
- DPOJET:PLOT<x>:EYE:EYEVerticalscale?

horizontal property 

horizontal: DpojetPlotItemEyeHorizontal

Return the DPOJET:PLOT<x>:EYE:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .autoscale: The DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale command.
  • .resolution: The DPOJET:PLOT<x>:EYE:HORizontal:RESolution command.
  • .xaxismax: The DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx command.
  • .xaxismin: The DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn command.

horizscale property 

horizscale: DpojetPlotItemEyeHorizscale

Return the DPOJET:PLOT<x>:EYE:HORIZScale command.

Description
  • This command sets or queries the horizontal scale state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORIZScale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORIZScale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORIZScale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORIZScale {1|0}
- DPOJET:PLOT<x>:EYE:HORIZScale?

interpolationfactor property 

interpolationfactor: DpojetPlotItemEyeInterpolationfactor

Return the DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor command.

Description
  • This command sets or queries eye diagram interpolation factor.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor {AUTO, TWELVEPOINTEIGHT, SIXTEEN}
- DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor?

interpolationtype property 

interpolationtype: DpojetPlotItemEyeInterpolationtype

Return the DPOJET:PLOT<x>:EYE:INTERPolationtype command.

Description
  • This command sets or queries the interpolation type.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:INTERPolationtype? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:INTERPolationtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:INTERPolationtype value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:INTERPolationtype { INTERPOLATION|NONINTERPOLATION }
- DPOJET:PLOT<x>:EYE:INTERPolationtype?

maskfile property 

maskfile: DpojetPlotItemEyeMaskfile

Return the DPOJET:PLOT<x>:EYE:MASKfile command.

Description
  • This command sets or queries the mask file. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:MASKfile? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:MASKfile? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:MASKfile value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:MASKfile <string>
- DPOJET:PLOT<x>:EYE:MASKfile?

state property 

state: DpojetPlotItemEyeState

Return the DPOJET:PLOT<x>:EYE:STATE command.

Description
  • This command sets or queries the eye state, either on or off. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:STATE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:STATE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:STATE {1|0}
- DPOJET:PLOT<x>:EYE:STATE?

superimpose property 

superimpose: DpojetPlotItemEyeSuperimpose

Return the DPOJET:PLOT<x>:EYE:SUPERImpose command.

Description
  • This command sets or queries whether superimposed eyes are generated in eye diagrams. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:SUPERImpose? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:SUPERImpose? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:SUPERImpose value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:SUPERImpose {1|0}
- DPOJET:PLOT<x>:EYE:SUPERImpose?

vertical property 

vertical: DpojetPlotItemEyeVertical

Return the DPOJET:PLOT<x>:EYE:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTical? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .yaxismax: The DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx command.
  • .yaxismin: The DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn command.

verticalalignment property 

verticalalignment: DpojetPlotItemEyeVerticalalignment

Return the DPOJET:PLOT<x>:EYE:VERTICALAlignment command.

Description
  • This command sets or queries the vertical alignment state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTICALAlignment? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTICALAlignment? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTICALAlignment value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTICALAlignment {1|0}
- DPOJET:PLOT<x>:EYE:VERTICALAlignment?

vertscale property 

vertscale: DpojetPlotItemEyeVertscale

Return the DPOJET:PLOT<x>:EYE:VERTScale command.

Description
  • This command sets or queries the vertical scale state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTScale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTScale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTScale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTScale {1|0}
- DPOJET:PLOT<x>:EYE:VERTScale?

DpojetPlotItemEyeAlignment

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:ALIGNment command.

Description
  • This command sets or queries eye alignment state for eye plots. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:ALIGNment? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:ALIGNment? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:ALIGNment value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:ALIGNment {AUTO|LEFT|CENter}
- DPOJET:PLOT<x>:EYE:ALIGNment?

DpojetPlotItemEyeEyeverticalscale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:EYEVerticalscale command.

Description
  • This command sets or queries eye diagram vertical scale when superimpose reference clock eye is checked.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:EYEVerticalscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:EYEVerticalscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:EYEVerticalscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:EYEVerticalscale {SCALETOData, SCALETORefclk}
- DPOJET:PLOT<x>:EYE:EYEVerticalscale?

DpojetPlotItemEyeHorizontal

Bases: SCPICmdRead

The DPOJET:PLOT<x>:EYE:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .autoscale: The DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale command.
  • .resolution: The DPOJET:PLOT<x>:EYE:HORizontal:RESolution command.
  • .xaxismax: The DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx command.
  • .xaxismin: The DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn command.

autoscale property 

autoscale: DpojetPlotItemEyeHorizontalAutoscale

Return the DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale command.

Description
  • This command sets or queries the horizontal auto scale setting. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale?

resolution property 

resolution: DpojetPlotItemEyeHorizontalResolution

Return the DPOJET:PLOT<x>:EYE:HORizontal:RESolution command.

Description
  • This command sets or queries the Horizontal Eye resolution. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:RESolution? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:RESolution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:RESolution value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:RESolution <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:RESolution?

xaxismax property 

xaxismax: DpojetPlotItemEyeHorizontalXaxismax

Return the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx command.

Description
  • This command sets or queries the X-Axis maximum value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx?

xaxismin property 

xaxismin: DpojetPlotItemEyeHorizontalXaxismin

Return the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn command.

Description
  • This command sets or queries the X-Axis minimum value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn?

DpojetPlotItemEyeHorizontalAutoscale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale command.

Description
  • This command sets or queries the horizontal auto scale setting. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:EYE:HORizontal:AUTOscale?

DpojetPlotItemEyeHorizontalResolution

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:HORizontal:RESolution command.

Description
  • This command sets or queries the Horizontal Eye resolution. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:RESolution? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:RESolution? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:RESolution value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:RESolution <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:RESolution?

DpojetPlotItemEyeHorizontalXaxismax

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx command.

Description
  • This command sets or queries the X-Axis maximum value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMAx?

DpojetPlotItemEyeHorizontalXaxismin

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn command.

Description
  • This command sets or queries the X-Axis minimum value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn <NR3>
- DPOJET:PLOT<x>:EYE:HORizontal:XAXISMIn?

DpojetPlotItemEyeHorizscale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:HORIZScale command.

Description
  • This command sets or queries the horizontal scale state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:HORIZScale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:HORIZScale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:HORIZScale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:HORIZScale {1|0}
- DPOJET:PLOT<x>:EYE:HORIZScale?

DpojetPlotItemEyeInterpolationfactor

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor command.

Description
  • This command sets or queries eye diagram interpolation factor.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor {AUTO, TWELVEPOINTEIGHT, SIXTEEN}
- DPOJET:PLOT<x>:EYE:INTERPOLATIONFactor?

DpojetPlotItemEyeInterpolationtype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:INTERPolationtype command.

Description
  • This command sets or queries the interpolation type.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:INTERPolationtype? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:INTERPolationtype? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:INTERPolationtype value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:INTERPolationtype { INTERPOLATION|NONINTERPOLATION }
- DPOJET:PLOT<x>:EYE:INTERPolationtype?

DpojetPlotItemEyeMaskfile

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:MASKfile command.

Description
  • This command sets or queries the mask file. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:MASKfile? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:MASKfile? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:MASKfile value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:MASKfile <string>
- DPOJET:PLOT<x>:EYE:MASKfile?

DpojetPlotItemEyeState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:STATE command.

Description
  • This command sets or queries the eye state, either on or off. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:STATE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:STATE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:STATE {1|0}
- DPOJET:PLOT<x>:EYE:STATE?

DpojetPlotItemEyeSuperimpose

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:SUPERImpose command.

Description
  • This command sets or queries whether superimposed eyes are generated in eye diagrams. Note: Undefined for noneye plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:SUPERImpose? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:SUPERImpose? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:SUPERImpose value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:SUPERImpose {1|0}
- DPOJET:PLOT<x>:EYE:SUPERImpose?

DpojetPlotItemEyeVertical

Bases: SCPICmdRead

The DPOJET:PLOT<x>:EYE:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTical? query and raise an AssertionError if the returned value does not match value.
Properties
  • .yaxismax: The DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx command.
  • .yaxismin: The DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn command.

yaxismax property 

yaxismax: DpojetPlotItemEyeVerticalYaxismax

Return the DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx command.

Description
  • This command sets or queries the Y-Axis maximum value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx <NR3>
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx?

yaxismin property 

yaxismin: DpojetPlotItemEyeVerticalYaxismin

Return the DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn command.

Description
  • This command sets or queries the Y-Axis minimum value
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn <NR3>
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn?

DpojetPlotItemEyeVerticalYaxismax

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx command.

Description
  • This command sets or queries the Y-Axis maximum value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx <NR3>
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMAx?

DpojetPlotItemEyeVerticalYaxismin

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn command.

Description
  • This command sets or queries the Y-Axis minimum value
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn <NR3>
- DPOJET:PLOT<x>:EYE:VERTical:YAXISMIn?

DpojetPlotItemEyeVerticalalignment

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:VERTICALAlignment command.

Description
  • This command sets or queries the vertical alignment state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTICALAlignment? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTICALAlignment? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTICALAlignment value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTICALAlignment {1|0}
- DPOJET:PLOT<x>:EYE:VERTICALAlignment?

DpojetPlotItemEyeVertscale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:EYE:VERTScale command.

Description
  • This command sets or queries the vertical scale state, either on or off.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:EYE:VERTScale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:EYE:VERTScale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:EYE:VERTScale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:EYE:VERTScale {1|0}
- DPOJET:PLOT<x>:EYE:VERTScale?

DpojetPlotItemHistogram

Bases: SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram? query and raise an AssertionError if the returned value does not match value.
Properties
  • .autoset: The DPOJET:PLOT<x>:HISTOgram:AUTOset command.
  • .horizontal: The DPOJET:PLOT<x>:HISTOgram:HORizontal command tree.
  • .numbins: The DPOJET:PLOT<x>:HISTOgram:NUMBins command.
  • .vertical: The DPOJET:PLOT<x>:HISTOgram:VERTical command tree.

autoset property 

autoset: DpojetPlotItemHistogramAutoset

Return the DPOJET:PLOT<x>:HISTOgram:AUTOset command.

Description
  • This command runs a histogram autoset for the specified slot. Note: Undefined for nonhistogram plots.
Usage
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:AUTOset value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:AUTOset {EXECute}

horizontal property 

horizontal: DpojetPlotItemHistogramHorizontal

Return the DPOJET:PLOT<x>:HISTOgram:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .autoscale: The DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale command.
  • .center: The DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter command.
  • .span: The DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN command.

numbins property 

numbins: DpojetPlotItemHistogramNumbins

Return the DPOJET:PLOT<x>:HISTOgram:NUMBins command.

Description
  • This command sets or queries the current histogram resolution. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:NUMBins value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:HISTOgram:NUMBins?

vertical property 

vertical: DpojetPlotItemHistogramVertical

Return the DPOJET:PLOT<x>:HISTOgram:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:VERTical? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE command.

DpojetPlotItemHistogramAutoset

Bases: SCPICmdWrite

The DPOJET:PLOT<x>:HISTOgram:AUTOset command.

Description
  • This command runs a histogram autoset for the specified slot. Note: Undefined for nonhistogram plots.
Usage
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:AUTOset value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:AUTOset {EXECute}

DpojetPlotItemHistogramHorizontal

Bases: SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .autoscale: The DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale command.
  • .center: The DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter command.
  • .span: The DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN command.

autoscale property 

autoscale: DpojetPlotItemHistogramHorizontalAutoscale

Return the DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale command.

Description
  • This command sets or queries the horizontal auto scale settings. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale?

center property 

center: DpojetPlotItemHistogramHorizontalCenter

Return the DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter command.

Description
  • This command sets or queries the histogram center. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter <NR3>
- DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter?

span property 

span: DpojetPlotItemHistogramHorizontalSpan

Return the DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN command.

Description
  • This command sets or queries the histogram span. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN <NR3>
- DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN?

DpojetPlotItemHistogramHorizontalAutoscale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale command.

Description
  • This command sets or queries the horizontal auto scale settings. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale {1|0}
- DPOJET:PLOT<x>:HISTOgram:HORizontal:AUTOscale?

DpojetPlotItemHistogramHorizontalCenter

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter command.

Description
  • This command sets or queries the histogram center. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter <NR3>
- DPOJET:PLOT<x>:HISTOgram:HORizontal:CENter?

DpojetPlotItemHistogramHorizontalSpan

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN command.

Description
  • This command sets or queries the histogram span. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN <NR3>
- DPOJET:PLOT<x>:HISTOgram:HORizontal:SPAN?

DpojetPlotItemHistogramNumbins

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram:NUMBins command.

Description
  • This command sets or queries the current histogram resolution. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:NUMBins? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:NUMBins? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:NUMBins value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- DPOJET:PLOT<x>:HISTOgram:NUMBins?

DpojetPlotItemHistogramVertical

Bases: SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:VERTical? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE command.

scale property 

scale: DpojetPlotItemHistogramVerticalScale

Return the DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE?

DpojetPlotItemHistogramVerticalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for nonhistogram plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:HISTOgram:VERTical:SCALE?

DpojetPlotItemNoisebathtub

Bases: SCPICmdRead

The DPOJET:PLOT<x>:NOISEBATHtub command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:NOISEBATHtub? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:NOISEBATHtub? query and raise an AssertionError if the returned value does not match value.
Properties
  • .yaxisunits: The DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits command.

yaxisunits property 

yaxisunits: DpojetPlotItemNoisebathtubYaxisunits

Return the DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits command.

Description
  • This command sets or queries the Y-Axis Units of Noise Bathtub.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits value command.
SCPI Syntax 
- DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits { UNITAmplitudes|VOLTs }
- DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits?

DpojetPlotItemNoisebathtubYaxisunits

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits command.

Description
  • This command sets or queries the Y-Axis Units of Noise Bathtub.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits value command.
SCPI Syntax 
- DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits { UNITAmplitudes|VOLTs }
- DPOJET:PLOT<x>:NOISEBATHtub:YAXISUnits?

DpojetPlotItemPdfeye

Bases: SCPICmdRead

The DPOJET:PLOT<x>:PDFEye command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ber1e12v: The DPOJET:PLOT<x>:PDFEye:BER1E12V command.
  • .ber1e15v: The DPOJET:PLOT<x>:PDFEye:BER1E15V command.
  • .ber1e18v: The DPOJET:PLOT<x>:PDFEye:BER1E18V command.
  • .ber1e6v: The DPOJET:PLOT<x>:PDFEye:BER1E6V command.
  • .ber1e9v: The DPOJET:PLOT<x>:PDFEye:BER1E9V command.
  • .targetber: The DPOJET:PLOT<x>:PDFEye:TARGETBER command.

ber1e12v property 

ber1e12v: DpojetPlotItemPdfeyeBer1e12v

Return the DPOJET:PLOT<x>:PDFEye:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E12V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E12V?

ber1e15v property 

ber1e15v: DpojetPlotItemPdfeyeBer1e15v

Return the DPOJET:PLOT<x>:PDFEye:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E15V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E15V?

ber1e18v property 

ber1e18v: DpojetPlotItemPdfeyeBer1e18v

Return the DPOJET:PLOT<x>:PDFEye:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E18V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E18V?

ber1e6v property 

ber1e6v: DpojetPlotItemPdfeyeBer1e6v

Return the DPOJET:PLOT<x>:PDFEye:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E6V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E6V?

ber1e9v property 

ber1e9v: DpojetPlotItemPdfeyeBer1e9v

Return the DPOJET:PLOT<x>:PDFEye:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E9V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E9V?

targetber property 

targetber: DpojetPlotItemPdfeyeTargetber

Return the DPOJET:PLOT<x>:PDFEye:TARGETBER command.

Description
  • This command sets or queries the TARGETBER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:TARGETBER {1|0}
- DPOJET:PLOT<x>:PDFEye:TARGETBER?

DpojetPlotItemPdfeyeBer1e12v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PDFEye:BER1E12V command.

Description
  • This command sets or queries the BER1E12 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E12V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E12V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E12V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E12V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E12V?

DpojetPlotItemPdfeyeBer1e15v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PDFEye:BER1E15V command.

Description
  • This command sets or queries the BER1E15 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E15V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E15V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E15V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E15V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E15V?

DpojetPlotItemPdfeyeBer1e18v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PDFEye:BER1E18V command.

Description
  • This command sets or queries the BER1E18 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E18V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E18V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E18V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E18V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E18V?

DpojetPlotItemPdfeyeBer1e6v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PDFEye:BER1E6V command.

Description
  • This command sets or queries the BER1E6 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E6V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E6V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E6V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E6V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E6V?

DpojetPlotItemPdfeyeBer1e9v

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PDFEye:BER1E9V command.

Description
  • This command sets or queries the BER1E9 Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:BER1E9V? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E9V? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:BER1E9V value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:BER1E9V {1|0}
- DPOJET:PLOT<x>:PDFEye:BER1E9V?

DpojetPlotItemPdfeyeTargetber

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PDFEye:TARGETBER command.

Description
  • This command sets or queries the TARGETBER Contour display.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PDFEye:TARGETBER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PDFEye:TARGETBER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PDFEye:TARGETBER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PDFEye:TARGETBER {1|0}
- DPOJET:PLOT<x>:PDFEye:TARGETBER?

DpojetPlotItemPhasenoise

Bases: SCPICmdRead

The DPOJET:PLOT<x>:PHASEnoise command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PHASEnoise? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PHASEnoise? query and raise an AssertionError if the returned value does not match value.
Properties
  • .baseline: The DPOJET:PLOT<x>:PHASEnoise:BASEline command.
  • .smootheningfilter: The DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter command.

baseline property 

baseline: DpojetPlotItemPhasenoiseBaseline

Return the DPOJET:PLOT<x>:PHASEnoise:BASEline command.

Description
  • This command sets or queries the phase noise baseline. Note: Undefined for nonphase-noise plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PHASEnoise:BASEline? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PHASEnoise:BASEline? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PHASEnoise:BASEline value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PHASEnoise:BASEline <NR3>
- DPOJET:PLOT<x>:PHASEnoise:BASEline?

smootheningfilter property 

smootheningfilter: DpojetPlotItemPhasenoiseSmootheningfilter

Return the DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter command.

Description
  • This command sets or queries the phase noise plot smoothing filter.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter {ONEBYHUNDREDTHdecade|ONEBYTENTHDECADE|ONEDECADE}
- DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter?

DpojetPlotItemPhasenoiseBaseline

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PHASEnoise:BASEline command.

Description
  • This command sets or queries the phase noise baseline. Note: Undefined for nonphase-noise plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PHASEnoise:BASEline? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PHASEnoise:BASEline? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PHASEnoise:BASEline value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PHASEnoise:BASEline <NR3>
- DPOJET:PLOT<x>:PHASEnoise:BASEline?

DpojetPlotItemPhasenoiseSmootheningfilter

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter command.

Description
  • This command sets or queries the phase noise plot smoothing filter.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter value command.
SCPI Syntax 
- DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter {ONEBYHUNDREDTHdecade|ONEBYTENTHDECADE|ONEDECADE}
- DPOJET:PLOT<x>:PHASEnoise:SMOOTHENINGFilter?

DpojetPlotItemSource

Bases: SCPICmdRead

The DPOJET:PLOT<x>:SOUrce command.

Description
  • This query-only command returns the source measurement for the selected plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SOUrce? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SOUrce? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:SOUrce?

DpojetPlotItemSpectrum

Bases: SCPICmdRead

The DPOJET:PLOT<x>:SPECtrum command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum? query and raise an AssertionError if the returned value does not match value.
Properties
  • .base: The DPOJET:PLOT<x>:SPECtrum:BASE command.
  • .horizontal: The DPOJET:PLOT<x>:SPECtrum:HORizontal command tree.
  • .mode: The DPOJET:PLOT<x>:SPECtrum:MODE command.
  • .vertical: The DPOJET:PLOT<x>:SPECtrum:VERTical command tree.

base property 

base: DpojetPlotItemSpectrumBase

Return the DPOJET:PLOT<x>:SPECtrum:BASE command.

Description
  • This command sets or queries the spectrum base. Undefined for non-spectrum plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:BASE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:BASE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:BASE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:BASE <NR3>
- DPOJET:PLOT<x>:SPECtrum:BASE?

horizontal property 

horizontal: DpojetPlotItemSpectrumHorizontal

Return the DPOJET:PLOT<x>:SPECtrum:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE command.

mode property 

mode: DpojetPlotItemSpectrumMode

Return the DPOJET:PLOT<x>:SPECtrum:MODE command.

Description
  • This command sets or queries the spectrum mode.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:MODE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:MODE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:MODE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:MODE {NORMal|AVErage|PEAKhold}
- DPOJET:PLOT<x>:SPECtrum:MODE?

vertical property 

vertical: DpojetPlotItemSpectrumVertical

Return the DPOJET:PLOT<x>:SPECtrum:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:VERTical? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE command.

DpojetPlotItemSpectrumBase

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:SPECtrum:BASE command.

Description
  • This command sets or queries the spectrum base. Undefined for non-spectrum plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:BASE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:BASE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:BASE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:BASE <NR3>
- DPOJET:PLOT<x>:SPECtrum:BASE?

DpojetPlotItemSpectrumHorizontal

Bases: SCPICmdRead

The DPOJET:PLOT<x>:SPECtrum:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE command.

scale property 

scale: DpojetPlotItemSpectrumHorizontalScale

Return the DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE command.

Description
  • This command sets or queries the horizontal scale setting for applicable plots, either Linear or Log. Note: Undefined for nonspectrum plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE?

DpojetPlotItemSpectrumHorizontalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE command.

Description
  • This command sets or queries the horizontal scale setting for applicable plots, either Linear or Log. Note: Undefined for nonspectrum plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:SPECtrum:HORizontal:SCALE?

DpojetPlotItemSpectrumMode

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:SPECtrum:MODE command.

Description
  • This command sets or queries the spectrum mode.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:MODE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:MODE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:MODE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:MODE {NORMal|AVErage|PEAKhold}
- DPOJET:PLOT<x>:SPECtrum:MODE?

DpojetPlotItemSpectrumVertical

Bases: SCPICmdRead

The DPOJET:PLOT<x>:SPECtrum:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:VERTical? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE command.

scale property 

scale: DpojetPlotItemSpectrumVerticalScale

Return the DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for nonspectrum plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE?

DpojetPlotItemSpectrumVerticalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Note: Undefined for nonspectrum plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:SPECtrum:VERTical:SCALE?

DpojetPlotItemTotaluisacquired

Bases: SCPICmdRead

The DPOJET:PLOT<x>:TOTALUISAcquired command.

Description
  • This command queries the total UIs acquired for Eye Diagram plot
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TOTALUISAcquired? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TOTALUISAcquired? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:TOTALUISAcquired?

DpojetPlotItemTotaluisanalyzed

Bases: SCPICmdRead

The DPOJET:PLOT<x>:TOTALUISAnalyzed command.

Description
  • This command queries the total UIs analysed for Eye Diagram plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TOTALUISAnalyzed? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TOTALUISAnalyzed? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:TOTALUISAnalyzed?

DpojetPlotItemTransfer

Bases: SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer? query and raise an AssertionError if the returned value does not match value.
Properties
  • .denominator: The DPOJET:PLOT<x>:TRANSfer:DENominator command.
  • .horizontal: The DPOJET:PLOT<x>:TRANSfer:HORizontal command tree.
  • .mode: The DPOJET:PLOT<x>:TRANSfer:MODE command.
  • .numerator: The DPOJET:PLOT<x>:TRANSfer:NUMerator command.
  • .vertical: The DPOJET:PLOT<x>:TRANSfer:VERTical command tree.

denominator property 

denominator: DpojetPlotItemTransferDenominator

Return the DPOJET:PLOT<x>:TRANSfer:DENominator command.

Description
  • This command sets or queries the transfer plot denominator. Note: Undefined for non-transfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:DENominator? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:DENominator? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:DENominator value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:DENominator {MEAS1 - MEAS99}
- DPOJET:PLOT<x>:TRANSfer:DENominator?

horizontal property 

horizontal: DpojetPlotItemTransferHorizontal

Return the DPOJET:PLOT<x>:TRANSfer:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE command.

mode property 

mode: DpojetPlotItemTransferMode

Return the DPOJET:PLOT<x>:TRANSfer:MODE command.

Description
  • This command sets or queries the transfer plot mode.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:MODE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:MODE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:MODE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:MODE {NORMal|AVErage}
- DPOJET:PLOT<x>:TRANSfer:MODE?

numerator property 

numerator: DpojetPlotItemTransferNumerator

Return the DPOJET:PLOT<x>:TRANSfer:NUMerator command.

Description
  • This command sets or queries the transfer plot numerator. Note: Undefined for nontransfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:NUMerator? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:NUMerator? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:NUMerator value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:NUMerator {MEAS1 - MEAS99}
- DPOJET:PLOT<x>:TRANSfer:NUMerator?

vertical property 

vertical: DpojetPlotItemTransferVertical

Return the DPOJET:PLOT<x>:TRANSfer:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:VERTical? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE command.

DpojetPlotItemTransferDenominator

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer:DENominator command.

Description
  • This command sets or queries the transfer plot denominator. Note: Undefined for non-transfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:DENominator? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:DENominator? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:DENominator value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:DENominator {MEAS1 - MEAS99}
- DPOJET:PLOT<x>:TRANSfer:DENominator?

DpojetPlotItemTransferHorizontal

Bases: SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE command.

scale property 

scale: DpojetPlotItemTransferHorizontalScale

Return the DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE command.

Description
  • This command sets or queries the horizontal scale setting for applicable plots, either Linear or Log. Undefined for nontransfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE?

DpojetPlotItemTransferHorizontalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE command.

Description
  • This command sets or queries the horizontal scale setting for applicable plots, either Linear or Log. Undefined for nontransfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:TRANSfer:HORizontal:SCALE?

DpojetPlotItemTransferMode

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer:MODE command.

Description
  • This command sets or queries the transfer plot mode.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:MODE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:MODE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:MODE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:MODE {NORMal|AVErage}
- DPOJET:PLOT<x>:TRANSfer:MODE?

DpojetPlotItemTransferNumerator

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer:NUMerator command.

Description
  • This command sets or queries the transfer plot numerator. Note: Undefined for nontransfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:NUMerator? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:NUMerator? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:NUMerator value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:NUMerator {MEAS1 - MEAS99}
- DPOJET:PLOT<x>:TRANSfer:NUMerator?

DpojetPlotItemTransferVertical

Bases: SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer:VERTical command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:VERTical? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:VERTical? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE command.

scale property 

scale: DpojetPlotItemTransferVerticalScale

Return the DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Undefined for non-transfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE?

DpojetPlotItemTransferVerticalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE command.

Description
  • This command sets or queries the vertical scale setting for applicable plots, either Linear or Log. Undefined for non-transfer plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:TRANSfer:VERTical:SCALE?

DpojetPlotItemTrend

Bases: SCPICmdRead

The DPOJET:PLOT<x>:TREND command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TREND? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TREND? query and raise an AssertionError if the returned value does not match value.
Properties
  • .type: The DPOJET:PLOT<x>:TREND:TYPe command.

type property 

type: DpojetPlotItemTrendType

Return the DPOJET:PLOT<x>:TREND:TYPe command.

Description
  • This command sets or queries the trend type setting for Trend plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TREND:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TREND:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TREND:TYPe value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TREND:TYPe {VECTOR|BAR}
- DPOJET:PLOT<x>:TREND:TYPe?

DpojetPlotItemTrendType

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:TREND:TYPe command.

Description
  • This command sets or queries the trend type setting for Trend plots.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TREND:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TREND:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:TREND:TYPe value command.
SCPI Syntax 
- DPOJET:PLOT<x>:TREND:TYPe {VECTOR|BAR}
- DPOJET:PLOT<x>:TREND:TYPe?

DpojetPlotItemType

Bases: SCPICmdRead

The DPOJET:PLOT<x>:TYPe command.

Description
  • This query-only command returns the current plot type for the selected plot.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:TYPe? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:TYPe?

DpojetPlotItemVertbathtub

Bases: SCPICmdRead

The DPOJET:PLOT<x>:VERTBATHtub command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ber: The DPOJET:PLOT<x>:VERTBATHtub:BER command.
  • .horizontal: The DPOJET:PLOT<x>:VERTBATHtub:HORizontal command tree.
  • .yaxisunits: The DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits command.

ber property 

ber: DpojetPlotItemVertbathtubBer

Return the DPOJET:PLOT<x>:VERTBATHtub:BER command.

Description
  • This command sets or queries the noise bathtub BER value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:BER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:BER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:VERTBATHtub:BER <NR3>
- DPOJET:PLOT<x>:VERTBATHtub:BER?

horizontal property 

horizontal: DpojetPlotItemVertbathtubHorizontal

Return the DPOJET:PLOT<x>:VERTBATHtub:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .scale: The DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE command.

yaxisunits property 

yaxisunits: DpojetPlotItemVertbathtubYaxisunits

Return the DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits command.

Description
  • This command sets or queries the Y-axis unit for noise bathtube.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits value command.
SCPI Syntax 
- DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits {VOLTs|UNITAMPLITUDES}
- DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits?

DpojetPlotItemVertbathtubBer

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:VERTBATHtub:BER command.

Description
  • This command sets or queries the noise bathtub BER value.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:BER? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:BER? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:BER value command.
SCPI Syntax 
- DPOJET:PLOT<x>:VERTBATHtub:BER <NR3>
- DPOJET:PLOT<x>:VERTBATHtub:BER?

DpojetPlotItemVertbathtubHorizontal

Bases: SCPICmdRead

The DPOJET:PLOT<x>:VERTBATHtub:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .scale: The DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE command.

scale property 

scale: DpojetPlotItemVertbathtubHorizontalScale

Return the DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE command.

Description
  • This command sets or queries the horizontal scale setting for applicable plots, either Linear or Log.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE?

DpojetPlotItemVertbathtubHorizontalScale

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE command.

Description
  • This command sets or queries the horizontal scale setting for applicable plots, either Linear or Log.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE value command.
SCPI Syntax 
- DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE {LINEAR|LOG}
- DPOJET:PLOT<x>:VERTBATHtub:HORizontal:SCALE?

DpojetPlotItemVertbathtubYaxisunits

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits command.

Description
  • This command sets or queries the Y-axis unit for noise bathtube.
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits value command.
SCPI Syntax 
- DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits {VOLTs|UNITAMPLITUDES}
- DPOJET:PLOT<x>:VERTBATHtub:YAXISUnits?

DpojetPlotItemXunits

Bases: SCPICmdRead

The DPOJET:PLOT<x>:XUnits command.

Description
  • This query-only command returns X units of the plot as a string. Note: Plot units depends on the measurement type.Click here to see the possible
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:XUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:XUnits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:XUnits?

DpojetPlotItemYunits

Bases: SCPICmdRead

The DPOJET:PLOT<x>:YUnits command.

Description
  • This query-only command returns Y units of the plot as a string. Note: Plot units depends on the measurement type.Click here to see the possible
Usage
  • Using the .query() method will send the DPOJET:PLOT<x>:YUnits? query.
  • Using the .verify(value) method will send the DPOJET:PLOT<x>:YUnits? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:PLOT<x>:YUnits?

DpojetPopulation

Bases: SCPICmdRead

The DPOJET:POPULATION command tree.

Usage
  • Using the .query() method will send the DPOJET:POPULATION? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION? query and raise an AssertionError if the returned value does not match value.
Properties
  • .condition: The DPOJET:POPULATION:CONDition command.
  • .limit: The DPOJET:POPULATION:LIMIT command.
  • .limitby: The DPOJET:POPULATION:LIMITBY command.
  • .state: The DPOJET:POPULATION:STATE command.

condition property 

condition: DpojetPopulationCondition

Return the DPOJET:POPULATION:CONDition command.

Description
  • This command sets or queries the current population limit condition.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:CONDition? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:CONDition? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:CONDition value command.
SCPI Syntax 
- DPOJET:POPULATION:CONDition {EACHmeas|LASTmeas}
- DPOJET:POPULATION:CONDition?

limit property 

limit: DpojetPopulationLimit

Return the DPOJET:POPULATION:LIMIT command.

Description
  • This command sets or queries the current limit value.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:LIMIT? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:LIMIT? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:LIMIT value command.
SCPI Syntax 
- DPOJET:POPULATION:LIMIT <NR3>
- DPOJET:POPULATION:LIMIT?

limitby property 

limitby: DpojetPopulationLimitby

Return the DPOJET:POPULATION:LIMITBY command.

Description
  • This command sets or queries the mechanism by limits, either acquisition or population.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:LIMITBY? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:LIMITBY? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:LIMITBY value command.
SCPI Syntax 
- DPOJET:POPULATION:LIMITBY {ACQuisitions|POPUlation}
- DPOJET:POPULATION:LIMITBY?

state property 

state: DpojetPopulationState

Return the DPOJET:POPULATION:STATE command.

Description
  • This command turns on or off population limits.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:STATE? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:STATE value command.
SCPI Syntax 
- DPOJET:POPULATION:STATE {1|0}
- DPOJET:POPULATION:STATE?

DpojetPopulationCondition

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:POPULATION:CONDition command.

Description
  • This command sets or queries the current population limit condition.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:CONDition? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:CONDition? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:CONDition value command.
SCPI Syntax 
- DPOJET:POPULATION:CONDition {EACHmeas|LASTmeas}
- DPOJET:POPULATION:CONDition?

DpojetPopulationLimit

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:POPULATION:LIMIT command.

Description
  • This command sets or queries the current limit value.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:LIMIT? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:LIMIT? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:LIMIT value command.
SCPI Syntax 
- DPOJET:POPULATION:LIMIT <NR3>
- DPOJET:POPULATION:LIMIT?

DpojetPopulationLimitby

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:POPULATION:LIMITBY command.

Description
  • This command sets or queries the mechanism by limits, either acquisition or population.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:LIMITBY? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:LIMITBY? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:LIMITBY value command.
SCPI Syntax 
- DPOJET:POPULATION:LIMITBY {ACQuisitions|POPUlation}
- DPOJET:POPULATION:LIMITBY?

DpojetPopulationState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:POPULATION:STATE command.

Description
  • This command turns on or off population limits.
Usage
  • Using the .query() method will send the DPOJET:POPULATION:STATE? query.
  • Using the .verify(value) method will send the DPOJET:POPULATION:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:POPULATION:STATE value command.
SCPI Syntax 
- DPOJET:POPULATION:STATE {1|0}
- DPOJET:POPULATION:STATE?

DpojetQualify

Bases: SCPICmdRead

The DPOJET:QUALify command tree.

Usage
  • Using the .query() method will send the DPOJET:QUALify? query.
  • Using the .verify(value) method will send the DPOJET:QUALify? query and raise an AssertionError if the returned value does not match value.
Properties
  • .active: The DPOJET:QUALify:ACTIVE command.
  • .source: The DPOJET:QUALify:SOUrce command.
  • .state: The DPOJET:QUALify:STATE command.

active property 

active: DpojetQualifyActive

Return the DPOJET:QUALify:ACTIVE command.

Description
  • This command sets the active state for the qualifier source, either HIGH or LOW.
Usage
  • Using the .query() method will send the DPOJET:QUALify:ACTIVE? query.
  • Using the .verify(value) method will send the DPOJET:QUALify:ACTIVE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:QUALify:ACTIVE value command.
SCPI Syntax 
- DPOJET:QUALify:ACTIVE {HIGH|LOW}
- DPOJET:QUALify:ACTIVE?

source property 

source: DpojetQualifySource

Return the DPOJET:QUALify:SOUrce command.

Description
  • This command sets the qualifier source.
Usage
  • Using the .query() method will send the DPOJET:QUALify:SOUrce? query.
  • Using the .verify(value) method will send the DPOJET:QUALify:SOUrce? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:QUALify:SOUrce value command.
SCPI Syntax 
- DPOJET:QUALify:SOUrce {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|SEARCH0 - SEARCH8}
- DPOJET:QUALify:SOUrce?

state property 

state: DpojetQualifyState

Return the DPOJET:QUALify:STATE command.

Description
  • This command turns on or off measurement qualification.
Usage
  • Using the .query() method will send the DPOJET:QUALify:STATE? query.
  • Using the .verify(value) method will send the DPOJET:QUALify:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:QUALify:STATE value command.
SCPI Syntax 
- DPOJET:QUALify:STATE {1|0}
- DPOJET:QUALify:STATE?

DpojetQualifyActive

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:QUALify:ACTIVE command.

Description
  • This command sets the active state for the qualifier source, either HIGH or LOW.
Usage
  • Using the .query() method will send the DPOJET:QUALify:ACTIVE? query.
  • Using the .verify(value) method will send the DPOJET:QUALify:ACTIVE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:QUALify:ACTIVE value command.
SCPI Syntax 
- DPOJET:QUALify:ACTIVE {HIGH|LOW}
- DPOJET:QUALify:ACTIVE?

DpojetQualifySource

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:QUALify:SOUrce command.

Description
  • This command sets the qualifier source.
Usage
  • Using the .query() method will send the DPOJET:QUALify:SOUrce? query.
  • Using the .verify(value) method will send the DPOJET:QUALify:SOUrce? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:QUALify:SOUrce value command.
SCPI Syntax 
- DPOJET:QUALify:SOUrce {CH1 - CH4|MATH1 - MATH4|REF1 - REF4|SEARCH0 - SEARCH8}
- DPOJET:QUALify:SOUrce?

DpojetQualifyState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:QUALify:STATE command.

Description
  • This command turns on or off measurement qualification.
Usage
  • Using the .query() method will send the DPOJET:QUALify:STATE? query.
  • Using the .verify(value) method will send the DPOJET:QUALify:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:QUALify:STATE value command.
SCPI Syntax 
- DPOJET:QUALify:STATE {1|0}
- DPOJET:QUALify:STATE?

DpojetReflevel

Bases: SCPICmdRead

The DPOJET:REFLevel command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevel? query.
  • Using the .verify(value) method will send the DPOJET:REFLevel? query and raise an AssertionError if the returned value does not match value.
Properties
  • .ch: The DPOJET:REFLevel:CH<x> command tree.

ch property 

ch: dict[int, DpojetReflevelChannel]

Return the DPOJET:REFLevel:CH<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevel:CH<x>? query.
  • Using the .verify(value) method will send the DPOJET:REFLevel:CH<x>? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .midzero: The DPOJET:REFLevel:CH<x>:MIDZero command.

DpojetReflevelChannel

Bases: ValidatedChannel, SCPICmdRead

The DPOJET:REFLevel:CH<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevel:CH<x>? query.
  • Using the .verify(value) method will send the DPOJET:REFLevel:CH<x>? query and raise an AssertionError if the returned value does not match value.
Properties
  • .midzero: The DPOJET:REFLevel:CH<x>:MIDZero command.

midzero property 

midzero: DpojetReflevelChannelMidzero

Return the DPOJET:REFLevel:CH<x>:MIDZero command.

Description
  • This command turns on or off the mid reference level voltage setting.
Usage
  • Using the .query() method will send the DPOJET:REFLevel:CH<x>:MIDZero? query.
  • Using the .verify(value) method will send the DPOJET:REFLevel:CH<x>:MIDZero? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevel:CH<x>:MIDZero value command.
SCPI Syntax 
- DPOJET:REFLevel:CH<x>:MIDZero {1|0}
- DPOJET:REFLevel:CH<x>:MIDZero?

DpojetReflevelChannelMidzero

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevel:CH<x>:MIDZero command.

Description
  • This command turns on or off the mid reference level voltage setting.
Usage
  • Using the .query() method will send the DPOJET:REFLevel:CH<x>:MIDZero? query.
  • Using the .verify(value) method will send the DPOJET:REFLevel:CH<x>:MIDZero? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevel:CH<x>:MIDZero value command.
SCPI Syntax 
- DPOJET:REFLevel:CH<x>:MIDZero {1|0}
- DPOJET:REFLevel:CH<x>:MIDZero?

DpojetReflevels

Bases: SCPICmdRead

The DPOJET:REFLevels command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevels? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels? query and raise an AssertionError if the returned value does not match value.
Properties
  • .autoset: The DPOJET:REFLevels:AUTOset command.
  • .ch: The DPOJET:REFLevels:CH<x> command tree.

autoset property 

autoset: DpojetReflevelsAutoset

Return the DPOJET:REFLevels:AUTOset command.

Description
  • This command performs a DPOJET ref level autoset on any sources selected using DPOJET:REFLevels:CH<x>:AUTOSet. Note: All pieces of the reflevel branch have the ability to set ref levels for CH1-CH4, MATH1-MATH4, and REF1-Ref4. Only the CH portion is shown in this OLH, but it exists and matches exactly for MATH (DPOJET:REFLevels:MATH<x> and REF (DPOJET:REFLevels:REF<x>).
Usage
  • Using the .write(value) method will send the DPOJET:REFLevels:AUTOset value command.
SCPI Syntax 
- DPOJET:REFLevels:AUTOset {EXECute}
Sub-properties
  • .state: The DPOJET:REFLevels:AUTOset:STATE command.

ch property 

ch: dict[int, DpojetReflevelsChannel]

Return the DPOJET:REFLevels:CH<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .absolute: The DPOJET:REFLevels:CH<x>:ABSolute command.
  • .autoset: The DPOJET:REFLevels:CH<x>:AUTOSet command.
  • .basetop: The DPOJET:REFLevels:CH<x>:BASETop command.
  • .percent: The DPOJET:REFLevels:CH<x>:PERcent command.

DpojetReflevelsAutoset

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:AUTOset command.

Description
  • This command performs a DPOJET ref level autoset on any sources selected using DPOJET:REFLevels:CH<x>:AUTOSet. Note: All pieces of the reflevel branch have the ability to set ref levels for CH1-CH4, MATH1-MATH4, and REF1-Ref4. Only the CH portion is shown in this OLH, but it exists and matches exactly for MATH (DPOJET:REFLevels:MATH<x> and REF (DPOJET:REFLevels:REF<x>).
Usage
  • Using the .write(value) method will send the DPOJET:REFLevels:AUTOset value command.
SCPI Syntax 
- DPOJET:REFLevels:AUTOset {EXECute}
Properties
  • .state: The DPOJET:REFLevels:AUTOset:STATE command.

state property 

state: DpojetReflevelsAutosetState

Return the DPOJET:REFLevels:AUTOset:STATE command.

Description
  • This query-only command provides the Ref Level Autoset status.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:AUTOset:STATE? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:AUTOset:STATE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REFLevels:AUTOset:STATE?

DpojetReflevelsAutosetState

Bases: SCPICmdRead

The DPOJET:REFLevels:AUTOset:STATE command.

Description
  • This query-only command provides the Ref Level Autoset status.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:AUTOset:STATE? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:AUTOset:STATE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REFLevels:AUTOset:STATE?

DpojetReflevelsChannel

Bases: ValidatedChannel, SCPICmdRead

The DPOJET:REFLevels:CH<x> command tree.

Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>? query and raise an AssertionError if the returned value does not match value.
Properties
  • .absolute: The DPOJET:REFLevels:CH<x>:ABSolute command.
  • .autoset: The DPOJET:REFLevels:CH<x>:AUTOSet command.
  • .basetop: The DPOJET:REFLevels:CH<x>:BASETop command.
  • .percent: The DPOJET:REFLevels:CH<x>:PERcent command.

absolute property 

absolute: DpojetReflevelsChannelAbsolute

Return the DPOJET:REFLevels:CH<x>:ABSolute command.

Description
  • This query only command provide the reference level parameters in absolute voltage values such as set hysteresis, Rise High Level, Rise Mid-Level, Rise Low Level, Fall High Level, Fall Mid-Level, Fall Low Level, each separated by comma in NR3 values.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute?
Sub-properties
  • .fallhigh: The DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh command.
  • .falllow: The DPOJET:REFLevels:CH<x>:ABSolute:FALLLow command.
  • .fallmid: The DPOJET:REFLevels:CH<x>:ABSolute:FALLMid command.
  • .hysteresis: The DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis command.
  • .risehigh: The DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh command.
  • .riselow: The DPOJET:REFLevels:CH<x>:ABSolute:RISELow command.
  • .risemid: The DPOJET:REFLevels:CH<x>:ABSolute:RISEMid command.

autoset property 

autoset: DpojetReflevelsChannelAutoset

Return the DPOJET:REFLevels:CH<x>:AUTOSet command.

Description
  • This command sets or clears the reflevel autoset state of the given source. When set to 1, the given source will have a ref level autoset acted on it during the next acquisition. Note: The Ref Level Autoset state is shown only for Ch1-Ch4 sources. It is the same for MATH and Ref waveforms. For example: DPOJET:REFLevels: MATH, DPOJET:REFLevels:REF<x>.
Usage
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:AUTOSet value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:AUTOSet {1|0}

basetop property 

basetop: DpojetReflevelsChannelBasetop

Return the DPOJET:REFLevels:CH<x>:BASETop command.

Description
  • This command sets the base-top method for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:BASETop? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:BASETop? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:BASETop value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:BASETop {MINMax|FULLhistogram|EYEhistogram|AUTO}
- DPOJET:REFLevels:CH<x>:BASETop?

percent property 

percent: DpojetReflevelsChannelPercent

Return the DPOJET:REFLevels:CH<x>:PERcent command.

Description
  • This query only command provide the reference level parameters in percentage such as set hysteresis values, Rise High Level, Rise Mid-Level, Rise Low Level, Fall High Level, Fall Mid-Level, Fall Low Level values each separated by comma in NR3 values. It also indicates the values are in percentage or absolute.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent?
Sub-properties
  • .fallhigh: The DPOJET:REFLevels:CH<x>:PERcent:FALLHigh command.
  • .falllow: The DPOJET:REFLevels:CH<x>:PERcent:FALLLow command.
  • .fallmid: The DPOJET:REFLevels:CH<x>:PERcent:FALLMid command.
  • .hysteresis: The DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis command.
  • .percentreflevel: The DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel command.
  • .risehigh: The DPOJET:REFLevels:CH<x>:PERcent:RISEHigh command.
  • .riselow: The DPOJET:REFLevels:CH<x>:PERcent:RISELow command.
  • .risemid: The DPOJET:REFLevels:CH<x>:PERcent:RISEMid command.

DpojetReflevelsChannelAbsolute

Bases: SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute command.

Description
  • This query only command provide the reference level parameters in absolute voltage values such as set hysteresis, Rise High Level, Rise Mid-Level, Rise Low Level, Fall High Level, Fall Mid-Level, Fall Low Level, each separated by comma in NR3 values.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute?
Properties
  • .fallhigh: The DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh command.
  • .falllow: The DPOJET:REFLevels:CH<x>:ABSolute:FALLLow command.
  • .fallmid: The DPOJET:REFLevels:CH<x>:ABSolute:FALLMid command.
  • .hysteresis: The DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis command.
  • .risehigh: The DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh command.
  • .riselow: The DPOJET:REFLevels:CH<x>:ABSolute:RISELow command.
  • .risemid: The DPOJET:REFLevels:CH<x>:ABSolute:RISEMid command.

fallhigh property 

fallhigh: DpojetReflevelsChannelAbsoluteFallhigh

Return the DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 1.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh?

falllow property 

falllow: DpojetReflevelsChannelAbsoluteFalllow

Return the DPOJET:REFLevels:CH<x>:ABSolute:FALLLow command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is -1.1.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLLow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLLow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:FALLLow <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLLow?

fallmid property 

fallmid: DpojetReflevelsChannelAbsoluteFallmid

Return the DPOJET:REFLevels:CH<x>:ABSolute:FALLMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 0.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:FALLMid <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLMid?

hysteresis property 

hysteresis: DpojetReflevelsChannelAbsoluteHysteresis

Return the DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis command.

Description
  • This command sets the hysteresis value used for autoset. The default is 0.03.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis?

risehigh property 

risehigh: DpojetReflevelsChannelAbsoluteRisehigh

Return the DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 1.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh?

riselow property 

riselow: DpojetReflevelsChannelAbsoluteRiselow

Return the DPOJET:REFLevels:CH<x>:ABSolute:RISELow command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is -1.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISELow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISELow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:RISELow <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISELow?

risemid property 

risemid: DpojetReflevelsChannelAbsoluteRisemid

Return the DPOJET:REFLevels:CH<x>:ABSolute:RISEMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 0.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:RISEMid <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISEMid?

DpojetReflevelsChannelAbsoluteFallhigh

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 1.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLHigh?

DpojetReflevelsChannelAbsoluteFalllow

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute:FALLLow command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is -1.1.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLLow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLLow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLLow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:FALLLow <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLLow?

DpojetReflevelsChannelAbsoluteFallmid

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute:FALLMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 0.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:FALLMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:FALLMid <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:FALLMid?

DpojetReflevelsChannelAbsoluteHysteresis

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis command.

Description
  • This command sets the hysteresis value used for autoset. The default is 0.03.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:HYSTeresis?

DpojetReflevelsChannelAbsoluteRisehigh

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 1.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISEHigh?

DpojetReflevelsChannelAbsoluteRiselow

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute:RISELow command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is -1.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISELow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISELow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISELow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:RISELow <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISELow?

DpojetReflevelsChannelAbsoluteRisemid

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:ABSolute:RISEMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset. The default is 0.0.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:ABSolute:RISEMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:ABSolute:RISEMid <NR3>
- DPOJET:REFLevels:CH<x>:ABSolute:RISEMid?

DpojetReflevelsChannelAutoset

Bases: SCPICmdWrite

The DPOJET:REFLevels:CH<x>:AUTOSet command.

Description
  • This command sets or clears the reflevel autoset state of the given source. When set to 1, the given source will have a ref level autoset acted on it during the next acquisition. Note: The Ref Level Autoset state is shown only for Ch1-Ch4 sources. It is the same for MATH and Ref waveforms. For example: DPOJET:REFLevels: MATH, DPOJET:REFLevels:REF<x>.
Usage
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:AUTOSet value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:AUTOSet {1|0}

DpojetReflevelsChannelBasetop

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:BASETop command.

Description
  • This command sets the base-top method for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:BASETop? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:BASETop? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:BASETop value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:BASETop {MINMax|FULLhistogram|EYEhistogram|AUTO}
- DPOJET:REFLevels:CH<x>:BASETop?

DpojetReflevelsChannelPercent

Bases: SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent command.

Description
  • This query only command provide the reference level parameters in percentage such as set hysteresis values, Rise High Level, Rise Mid-Level, Rise Low Level, Fall High Level, Fall Mid-Level, Fall Low Level values each separated by comma in NR3 values. It also indicates the values are in percentage or absolute.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent?
Properties
  • .fallhigh: The DPOJET:REFLevels:CH<x>:PERcent:FALLHigh command.
  • .falllow: The DPOJET:REFLevels:CH<x>:PERcent:FALLLow command.
  • .fallmid: The DPOJET:REFLevels:CH<x>:PERcent:FALLMid command.
  • .hysteresis: The DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis command.
  • .percentreflevel: The DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel command.
  • .risehigh: The DPOJET:REFLevels:CH<x>:PERcent:RISEHigh command.
  • .riselow: The DPOJET:REFLevels:CH<x>:PERcent:RISELow command.
  • .risemid: The DPOJET:REFLevels:CH<x>:PERcent:RISEMid command.

fallhigh property 

fallhigh: DpojetReflevelsChannelPercentFallhigh

Return the DPOJET:REFLevels:CH<x>:PERcent:FALLHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:FALLHigh <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLHigh?

falllow property 

falllow: DpojetReflevelsChannelPercentFalllow

Return the DPOJET:REFLevels:CH<x>:PERcent:FALLLow command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLLow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLLow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLLow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:FALLLow <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLLow?

fallmid property 

fallmid: DpojetReflevelsChannelPercentFallmid

Return the DPOJET:REFLevels:CH<x>:PERcent:FALLMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:FALLMid <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLMid?

hysteresis property 

hysteresis: DpojetReflevelsChannelPercentHysteresis

Return the DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis command.

Description
  • This command sets the hysteresis value used for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis?

percentreflevel property 

percentreflevel: DpojetReflevelsChannelPercentPercentreflevel

Return the DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel command.

Description
  • This command sets or gets the Reference Levels to Percentage or Absolute. Note: The reflevel commands can be used to set ref levels for CH1-CH4, MATH1-MATH4, and REF1-REF4. The command syntax in OLH is shown only for CH. Use MATH and REF for MATH1-MATH4, and REF1-REF4 (DPOJET:REFLevels:MATH<x> and REF (DPOJET:REFLevels:REF<x>).
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel { 1|0 }
- DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel?

risehigh property 

risehigh: DpojetReflevelsChannelPercentRisehigh

Return the DPOJET:REFLevels:CH<x>:PERcent:RISEHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:RISEHigh <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISEHigh?

riselow property 

riselow: DpojetReflevelsChannelPercentRiselow

Return the DPOJET:REFLevels:CH<x>:PERcent:RISELow command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:RISELow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISELow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISELow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:RISELow <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISELow?

risemid property 

risemid: DpojetReflevelsChannelPercentRisemid

Return the DPOJET:REFLevels:CH<x>:PERcent:RISEMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:RISEMid <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISEMid?

DpojetReflevelsChannelPercentFallhigh

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:FALLHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:FALLHigh <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLHigh?

DpojetReflevelsChannelPercentFalllow

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:FALLLow command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLLow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLLow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLLow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:FALLLow <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLLow?

DpojetReflevelsChannelPercentFallmid

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:FALLMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:FALLMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:FALLMid <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:FALLMid?

DpojetReflevelsChannelPercentHysteresis

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis command.

Description
  • This command sets the hysteresis value used for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:HYSTeresis?

DpojetReflevelsChannelPercentPercentreflevel

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel command.

Description
  • This command sets or gets the Reference Levels to Percentage or Absolute. Note: The reflevel commands can be used to set ref levels for CH1-CH4, MATH1-MATH4, and REF1-REF4. The command syntax in OLH is shown only for CH. Use MATH and REF for MATH1-MATH4, and REF1-REF4 (DPOJET:REFLevels:MATH<x> and REF (DPOJET:REFLevels:REF<x>).
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel { 1|0 }
- DPOJET:REFLevels:CH<x>:PERcent:PERCENTReflevel?

DpojetReflevelsChannelPercentRisehigh

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:RISEHigh command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEHigh? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEHigh? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEHigh value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:RISEHigh <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISEHigh?

DpojetReflevelsChannelPercentRiselow

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:RISELow command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:RISELow? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISELow? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISELow value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:RISELow <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISELow?

DpojetReflevelsChannelPercentRisemid

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REFLevels:CH<x>:PERcent:RISEMid command.

Description
  • This command sets the ref level voltage relative to base top for autoset.
Usage
  • Using the .query() method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEMid? query.
  • Using the .verify(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEMid? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REFLevels:CH<x>:PERcent:RISEMid value command.
SCPI Syntax 
- DPOJET:REFLevels:CH<x>:PERcent:RISEMid <NR3>
- DPOJET:REFLevels:CH<x>:PERcent:RISEMid?

DpojetReport

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT command.

Description
  • These are set-only commands. EXECute executes a DPOJET report save operation for the currently defined report configuration. APPEnd appends new data to the selected report. Note: Ensure to close the PDF report before append.
Usage
  • Using the .write(value) method will send the DPOJET:REPORT value command.
SCPI Syntax 
- DPOJET:REPORT {EXECute|APPEnd}
Properties
  • .applicationconfig: The DPOJET:REPORT:APPlicationconfig command.
  • .autoincrement: The DPOJET:REPORT:AUTOincrement command.
  • .comments: The DPOJET:REPORT:COMments command.
  • .detailedresults: The DPOJET:REPORT:DETailedresults command.
  • .enablecomments: The DPOJET:REPORT:ENABlecomments command.
  • .getimage: The DPOJET:REPORT:GETIMAGE command.
  • .getimagename: The DPOJET:REPORT:GETIMAGEName command.
  • .getxmlreport: The DPOJET:REPORT:GETXMLReport command.
  • .passfailresults: The DPOJET:REPORT:PASSFailresults command.
  • .plotimages: The DPOJET:REPORT:PLOTimages command.
  • .reportname: The DPOJET:REPORT:REPORTName command.
  • .savewaveforms: The DPOJET:REPORT:SAVEWaveforms command.
  • .setimagepath: The DPOJET:REPORT:SETIMAGEPath command.
  • .setupconfig: The DPOJET:REPORT:SETupconfig command.
  • .state: The DPOJET:REPORT:STATE command.
  • .type: The DPOJET:REPORT:TYPe command.
  • .viewreport: The DPOJET:REPORT:VIEWreport command.

applicationconfig property 

applicationconfig: DpojetReportApplicationconfig

Return the DPOJET:REPORT:APPlicationconfig command.

Description
  • This command turns on or off including complete application configuration in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:APPlicationconfig? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:APPlicationconfig? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:APPlicationconfig value command.
SCPI Syntax 
- DPOJET:REPORT:APPlicationconfig {1|0}
- DPOJET:REPORT:APPlicationconfig?

autoincrement property 

autoincrement: DpojetReportAutoincrement

Return the DPOJET:REPORT:AUTOincrement command.

Description
  • This command turns on or off auto increment of report file names.
Usage
  • Using the .query() method will send the DPOJET:REPORT:AUTOincrement? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:AUTOincrement? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:AUTOincrement value command.
SCPI Syntax 
- DPOJET:REPORT:AUTOincrement {1|0}
- DPOJET:REPORT:AUTOincrement?

comments property 

comments: DpojetReportComments

Return the DPOJET:REPORT:COMments command.

Description
  • This command sets or queries the comments.
Usage
  • Using the .query() method will send the DPOJET:REPORT:COMments? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:COMments? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:COMments value command.
SCPI Syntax 
- DPOJET:REPORT:COMments <string>
- DPOJET:REPORT:COMments?

detailedresults property 

detailedresults: DpojetReportDetailedresults

Return the DPOJET:REPORT:DETailedresults command.

Description
  • This command turns on or off including detailed results in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:DETailedresults? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:DETailedresults? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:DETailedresults value command.
SCPI Syntax 
- DPOJET:REPORT:DETailedresults {1|0}
- DPOJET:REPORT:DETailedresults?

enablecomments property 

enablecomments: DpojetReportEnablecomments

Return the DPOJET:REPORT:ENABlecomments command.

Description
  • This command sets or queries the comments enable or disable settings.
Usage
  • Using the .query() method will send the DPOJET:REPORT:ENABlecomments? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:ENABlecomments? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:ENABlecomments value command.
SCPI Syntax 
- DPOJET:REPORT:ENABlecomments {1|0}
- DPOJET:REPORT:ENABlecomments?

getimage property 

getimage: DpojetReportGetimage

Return the DPOJET:REPORT:GETIMAGE command.

Description
  • This command returns the image which is set using DPOJET:REPORT:SETIMAGEPath command in binary format.
Usage
  • Using the .query() method will send the DPOJET:REPORT:GETIMAGE? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:GETIMAGE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:GETIMAGE?

getimagename property 

getimagename: DpojetReportGetimagename

Return the DPOJET:REPORT:GETIMAGEName command.

Description
  • This query only commands gets all the PNG format image names from this directory C:UsersTektronixTekApplicationsDPOJETReportsResources.
Usage
  • Using the .query() method will send the DPOJET:REPORT:GETIMAGEName? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:GETIMAGEName? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:GETIMAGEName?

getxmlreport property 

getxmlreport: DpojetReportGetxmlreport

Return the DPOJET:REPORT:GETXMLReport command.

Description
  • This query only command retrieve the report in binary format
Usage
  • Using the .query() method will send the DPOJET:REPORT:GETXMLReport? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:GETXMLReport? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:GETXMLReport?

passfailresults property 

passfailresults: DpojetReportPassfailresults

Return the DPOJET:REPORT:PASSFailresults command.

Description
  • This command turns on or off including pass/fail results in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:PASSFailresults? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:PASSFailresults? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:PASSFailresults value command.
SCPI Syntax 
- DPOJET:REPORT:PASSFailresults {1|0}
- DPOJET:REPORT:PASSFailresults?

plotimages property 

plotimages: DpojetReportPlotimages

Return the DPOJET:REPORT:PLOTimages command.

Description
  • This command turns on or off including detailed plot images in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:PLOTimages? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:PLOTimages? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:PLOTimages value command.
SCPI Syntax 
- DPOJET:REPORT:PLOTimages {1|0}
- DPOJET:REPORT:PLOTimages?

reportname property 

reportname: DpojetReportReportname

Return the DPOJET:REPORT:REPORTName command.

Description
  • This command sets the current report file name.
Usage
  • Using the .query() method will send the DPOJET:REPORT:REPORTName? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:REPORTName? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:REPORTName value command.
SCPI Syntax 
- DPOJET:REPORT:REPORTName <string>
- DPOJET:REPORT:REPORTName?

savewaveforms property 

savewaveforms: DpojetReportSavewaveforms

Return the DPOJET:REPORT:SAVEWaveforms command.

Description
  • This command turns on or off saving waveforms when a report save/append is invoked.
Usage
  • Using the .query() method will send the DPOJET:REPORT:SAVEWaveforms? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:SAVEWaveforms? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:SAVEWaveforms value command.
SCPI Syntax 
- DPOJET:REPORT:SAVEWaveforms {1|0}
- DPOJET:REPORT:SAVEWaveforms?

setimagepath property 

setimagepath: DpojetReportSetimagepath

Return the DPOJET:REPORT:SETIMAGEPath command.

Description
  • This command sets the path of the image which you want to retreive using DPOJET:REPORT:GETIMAGE command.
Usage
  • Using the .write(value) method will send the DPOJET:REPORT:SETIMAGEPath value command.
SCPI Syntax 
- DPOJET:REPORT:SETIMAGEPath <file string>

setupconfig property 

setupconfig: DpojetReportSetupconfig

Return the DPOJET:REPORT:SETupconfig command.

Description
  • This command turns on or off including setup configuration in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:SETupconfig? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:SETupconfig? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:SETupconfig value command.
SCPI Syntax 
- DPOJET:REPORT:SETupconfig {1|0}
- DPOJET:REPORT:SETupconfig?

state property 

state: DpojetReportState

Return the DPOJET:REPORT:STATE command.

Description
  • This query-only command provides the report status.
Usage
  • Using the .query() method will send the DPOJET:REPORT:STATE? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:STATE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:STATE?

type property 

type: DpojetReportType

Return the DPOJET:REPORT:TYPe command.

Description
  • This command sets or queries the report type.
Usage
  • Using the .query() method will send the DPOJET:REPORT:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:TYPe value command.
SCPI Syntax 
- DPOJET:REPORT:TYPe {MHT|PDF}
- DPOJET:REPORT:TYPe?

viewreport property 

viewreport: DpojetReportViewreport

Return the DPOJET:REPORT:VIEWreport command.

Description
  • This command turns on or off viewing report after generation.
Usage
  • Using the .query() method will send the DPOJET:REPORT:VIEWreport? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:VIEWreport? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:VIEWreport value command.
SCPI Syntax 
- DPOJET:REPORT:VIEWreport {1|0}
- DPOJET:REPORT:VIEWreport?

DpojetReportApplicationconfig

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:APPlicationconfig command.

Description
  • This command turns on or off including complete application configuration in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:APPlicationconfig? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:APPlicationconfig? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:APPlicationconfig value command.
SCPI Syntax 
- DPOJET:REPORT:APPlicationconfig {1|0}
- DPOJET:REPORT:APPlicationconfig?

DpojetReportAutoincrement

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:AUTOincrement command.

Description
  • This command turns on or off auto increment of report file names.
Usage
  • Using the .query() method will send the DPOJET:REPORT:AUTOincrement? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:AUTOincrement? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:AUTOincrement value command.
SCPI Syntax 
- DPOJET:REPORT:AUTOincrement {1|0}
- DPOJET:REPORT:AUTOincrement?

DpojetReportComments

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:COMments command.

Description
  • This command sets or queries the comments.
Usage
  • Using the .query() method will send the DPOJET:REPORT:COMments? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:COMments? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:COMments value command.
SCPI Syntax 
- DPOJET:REPORT:COMments <string>
- DPOJET:REPORT:COMments?

DpojetReportDetailedresults

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:DETailedresults command.

Description
  • This command turns on or off including detailed results in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:DETailedresults? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:DETailedresults? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:DETailedresults value command.
SCPI Syntax 
- DPOJET:REPORT:DETailedresults {1|0}
- DPOJET:REPORT:DETailedresults?

DpojetReportEnablecomments

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:ENABlecomments command.

Description
  • This command sets or queries the comments enable or disable settings.
Usage
  • Using the .query() method will send the DPOJET:REPORT:ENABlecomments? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:ENABlecomments? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:ENABlecomments value command.
SCPI Syntax 
- DPOJET:REPORT:ENABlecomments {1|0}
- DPOJET:REPORT:ENABlecomments?

DpojetReportGetimage

Bases: SCPICmdRead

The DPOJET:REPORT:GETIMAGE command.

Description
  • This command returns the image which is set using DPOJET:REPORT:SETIMAGEPath command in binary format.
Usage
  • Using the .query() method will send the DPOJET:REPORT:GETIMAGE? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:GETIMAGE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:GETIMAGE?

DpojetReportGetimagename

Bases: SCPICmdRead

The DPOJET:REPORT:GETIMAGEName command.

Description
  • This query only commands gets all the PNG format image names from this directory C:UsersTektronixTekApplicationsDPOJETReportsResources.
Usage
  • Using the .query() method will send the DPOJET:REPORT:GETIMAGEName? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:GETIMAGEName? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:GETIMAGEName?

DpojetReportGetxmlreport

Bases: SCPICmdRead

The DPOJET:REPORT:GETXMLReport command.

Description
  • This query only command retrieve the report in binary format
Usage
  • Using the .query() method will send the DPOJET:REPORT:GETXMLReport? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:GETXMLReport? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:GETXMLReport?

DpojetReportPassfailresults

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:PASSFailresults command.

Description
  • This command turns on or off including pass/fail results in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:PASSFailresults? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:PASSFailresults? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:PASSFailresults value command.
SCPI Syntax 
- DPOJET:REPORT:PASSFailresults {1|0}
- DPOJET:REPORT:PASSFailresults?

DpojetReportPlotimages

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:PLOTimages command.

Description
  • This command turns on or off including detailed plot images in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:PLOTimages? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:PLOTimages? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:PLOTimages value command.
SCPI Syntax 
- DPOJET:REPORT:PLOTimages {1|0}
- DPOJET:REPORT:PLOTimages?

DpojetReportReportname

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:REPORTName command.

Description
  • This command sets the current report file name.
Usage
  • Using the .query() method will send the DPOJET:REPORT:REPORTName? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:REPORTName? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:REPORTName value command.
SCPI Syntax 
- DPOJET:REPORT:REPORTName <string>
- DPOJET:REPORT:REPORTName?

DpojetReportSavewaveforms

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:SAVEWaveforms command.

Description
  • This command turns on or off saving waveforms when a report save/append is invoked.
Usage
  • Using the .query() method will send the DPOJET:REPORT:SAVEWaveforms? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:SAVEWaveforms? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:SAVEWaveforms value command.
SCPI Syntax 
- DPOJET:REPORT:SAVEWaveforms {1|0}
- DPOJET:REPORT:SAVEWaveforms?

DpojetReportSetimagepath

Bases: SCPICmdWrite

The DPOJET:REPORT:SETIMAGEPath command.

Description
  • This command sets the path of the image which you want to retreive using DPOJET:REPORT:GETIMAGE command.
Usage
  • Using the .write(value) method will send the DPOJET:REPORT:SETIMAGEPath value command.
SCPI Syntax 
- DPOJET:REPORT:SETIMAGEPath <file string>

DpojetReportSetupconfig

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:SETupconfig command.

Description
  • This command turns on or off including setup configuration in reports.
Usage
  • Using the .query() method will send the DPOJET:REPORT:SETupconfig? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:SETupconfig? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:SETupconfig value command.
SCPI Syntax 
- DPOJET:REPORT:SETupconfig {1|0}
- DPOJET:REPORT:SETupconfig?

DpojetReportState

Bases: SCPICmdRead

The DPOJET:REPORT:STATE command.

Description
  • This query-only command provides the report status.
Usage
  • Using the .query() method will send the DPOJET:REPORT:STATE? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:STATE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:REPORT:STATE?

DpojetReportType

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:TYPe command.

Description
  • This command sets or queries the report type.
Usage
  • Using the .query() method will send the DPOJET:REPORT:TYPe? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:TYPe? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:TYPe value command.
SCPI Syntax 
- DPOJET:REPORT:TYPe {MHT|PDF}
- DPOJET:REPORT:TYPe?

DpojetReportViewreport

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:REPORT:VIEWreport command.

Description
  • This command turns on or off viewing report after generation.
Usage
  • Using the .query() method will send the DPOJET:REPORT:VIEWreport? query.
  • Using the .verify(value) method will send the DPOJET:REPORT:VIEWreport? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:REPORT:VIEWreport value command.
SCPI Syntax 
- DPOJET:REPORT:VIEWreport {1|0}
- DPOJET:REPORT:VIEWreport?

DpojetResults

Bases: SCPICmdRead

The DPOJET:RESULts command tree.

Usage
  • Using the .query() method will send the DPOJET:RESULts? query.
  • Using the .verify(value) method will send the DPOJET:RESULts? query and raise an AssertionError if the returned value does not match value.
Properties
  • .getallresults: The DPOJET:RESULts:GETALLResults command.
  • .status: The DPOJET:RESULts:STATus command.
  • .view: The DPOJET:RESULts:VIew command.

getallresults property 

getallresults: DpojetResultsGetallresults

Return the DPOJET:RESULts:GETALLResults command.

Description
  • The query only command returns all the measurement results in binary format. This command is similar to curve query.
Usage
  • Using the .query() method will send the DPOJET:RESULts:GETALLResults? query.
  • Using the .verify(value) method will send the DPOJET:RESULts:GETALLResults? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:RESULts:GETALLResults?

status property 

status: DpojetResultsStatus

Return the DPOJET:RESULts:STATus command.

Description
  • This query-only command returns the overall pass/fail status.
Usage
  • Using the .query() method will send the DPOJET:RESULts:STATus? query.
  • Using the .verify(value) method will send the DPOJET:RESULts:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:RESULts:STATus?

view property 

view: DpojetResultsView

Return the DPOJET:RESULts:VIew command.

Description
  • This command sets or queries the results view type.
Usage
  • Using the .query() method will send the DPOJET:RESULts:VIew? query.
  • Using the .verify(value) method will send the DPOJET:RESULts:VIew? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:RESULts:VIew value command.
SCPI Syntax 
- DPOJET:RESULts:VIew {SUMmary|DETails}
- DPOJET:RESULts:VIew?

DpojetResultsGetallresults

Bases: SCPICmdRead

The DPOJET:RESULts:GETALLResults command.

Description
  • The query only command returns all the measurement results in binary format. This command is similar to curve query.
Usage
  • Using the .query() method will send the DPOJET:RESULts:GETALLResults? query.
  • Using the .verify(value) method will send the DPOJET:RESULts:GETALLResults? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:RESULts:GETALLResults?

DpojetResultsStatus

Bases: SCPICmdRead

The DPOJET:RESULts:STATus command.

Description
  • This query-only command returns the overall pass/fail status.
Usage
  • Using the .query() method will send the DPOJET:RESULts:STATus? query.
  • Using the .verify(value) method will send the DPOJET:RESULts:STATus? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:RESULts:STATus?

DpojetResultsView

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:RESULts:VIew command.

Description
  • This command sets or queries the results view type.
Usage
  • Using the .query() method will send the DPOJET:RESULts:VIew? query.
  • Using the .verify(value) method will send the DPOJET:RESULts:VIew? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:RESULts:VIew value command.
SCPI Syntax 
- DPOJET:RESULts:VIew {SUMmary|DETails}
- DPOJET:RESULts:VIew?

DpojetSave

Bases: SCPICmdWrite

The DPOJET:SAVE command.

Description
  • This set-only command saves the specified DPOJET measurement result to the specified ref. For Example: DPOJET:SAVE MEAS4, REF2.
Usage
  • Using the .write(value) method will send the DPOJET:SAVE value command.
SCPI Syntax 
- DPOJET:SAVE {MEAS<x>|REF<x>}

DpojetSaveallplots

Bases: SCPICmdWriteNoArguments

The DPOJET:SAVEALLPLOTS command.

Description
  • Saves all the plots to Reports/Resource folder.
Usage
  • Using the .write() method will send the DPOJET:SAVEALLPLOTS command.
SCPI Syntax 
- DPOJET:SAVEALLPLOTS

DpojetSetimagetpath

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:SETIMAGETPath command.

Description
  • This command sets or queries the image path of the DPOJET application.
Usage
  • Using the .query() method will send the DPOJET:SETIMAGETPath? query.
  • Using the .verify(value) method will send the DPOJET:SETIMAGETPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SETIMAGETPath value command.
SCPI Syntax 
- DPOJET:SETIMAGETPath <file string>
- DPOJET:SETIMAGETPath?

DpojetSetloggingpath

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:SETLOGGINGPath command.

Description
  • This command sets or queries the Logging path of the DPOJET application.
Usage
  • Using the .query() method will send the DPOJET:SETLOGGINGPath? query.
  • Using the .verify(value) method will send the DPOJET:SETLOGGINGPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SETLOGGINGPath value command.
SCPI Syntax 
- DPOJET:SETLOGGINGPath <file string>
- DPOJET:SETLOGGINGPath?

DpojetSetreportpath

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:SETREPORTPath command.

Description
  • This command sets or queries the Report path of the DPOJET application.
Usage
  • Using the .query() method will send the DPOJET:SETREPORTPath? query.
  • Using the .verify(value) method will send the DPOJET:SETREPORTPath? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SETREPORTPath value command.
SCPI Syntax 
- DPOJET:SETREPORTPath <file string>
- DPOJET:SETREPORTPath?

DpojetShowmeaswarning

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:SHOWMEASWARNing command.

Description
  • This sets or queries the visibility of Reference Level Autoset warnings, either on or off.
Usage
  • Using the .query() method will send the DPOJET:SHOWMEASWARNing? query.
  • Using the .verify(value) method will send the DPOJET:SHOWMEASWARNing? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SHOWMEASWARNing value command.
SCPI Syntax 
- DPOJET:SHOWMEASWARNing {1|0}
- DPOJET:SHOWMEASWARNing?

DpojetSnc

Bases: SCPICmdRead

The DPOJET:SNC command tree.

Usage
  • Using the .query() method will send the DPOJET:SNC? query.
  • Using the .verify(value) method will send the DPOJET:SNC? query and raise an AssertionError if the returned value does not match value.
Properties
  • .activate: The DPOJET:SNC:ACTIvate command.
  • .close: The DPOJET:SNC:CLOse command.

activate property 

activate: DpojetSncActivate

Return the DPOJET:SNC:ACTIvate command.

Description
  • This set only command activates Scope Noise Characterization application.
Usage
  • Using the .write() method will send the DPOJET:SNC:ACTIvate command.
SCPI Syntax 
- DPOJET:SNC:ACTIvate

close property 

close: DpojetSncClose

Return the DPOJET:SNC:CLOse command.

Description
  • This set only command closes Scope Noise Characterization application. Note: When the Scope Noise Characterization application is launched using the
Usage
  • Using the .write() method will send the DPOJET:SNC:CLOse command.
SCPI Syntax 
- DPOJET:SNC:CLOse

DpojetSncActivate

Bases: SCPICmdWriteNoArguments

The DPOJET:SNC:ACTIvate command.

Description
  • This set only command activates Scope Noise Characterization application.
Usage
  • Using the .write() method will send the DPOJET:SNC:ACTIvate command.
SCPI Syntax 
- DPOJET:SNC:ACTIvate

DpojetSncClose

Bases: SCPICmdWriteNoArguments

The DPOJET:SNC:CLOse command.

Description
  • This set only command closes Scope Noise Characterization application. Note: When the Scope Noise Characterization application is launched using the
Usage
  • Using the .write() method will send the DPOJET:SNC:CLOse command.
SCPI Syntax 
- DPOJET:SNC:CLOse

DpojetSourceautoset

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:SOURCEAutoset command.

Description
  • This command performs a DPOJET horizontal, vertical, or autoset on both horizontal and vertical for any sources used in current measurements.
Usage
  • Using the .write(value) method will send the DPOJET:SOURCEAutoset value command.
SCPI Syntax 
- DPOJET:SOURCEAutoset {HORizontal|VERTical|BOTH}
Properties
  • .horizontal: The DPOJET:SOURCEAutoset:HORizontal command tree.
  • .state: The DPOJET:SOURCEAutoset:STATE command.

horizontal property 

horizontal: DpojetSourceautosetHorizontal

Return the DPOJET:SOURCEAutoset:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:HORizontal? query and raise an AssertionError if the returned value does not match value.
Sub-properties
  • .uicount: The DPOJET:SOURCEAutoset:HORizontal:UICount command.
  • .uivalue: The DPOJET:SOURCEAutoset:HORizontal:UIValue command.

state property 

state: DpojetSourceautosetState

Return the DPOJET:SOURCEAutoset:STATE command.

Description
  • This query-only command provides the Source Autoset status.
Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:STATE? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:STATE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:SOURCEAutoset:STATE?

DpojetSourceautosetHorizontal

Bases: SCPICmdRead

The DPOJET:SOURCEAutoset:HORizontal command tree.

Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:HORizontal? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:HORizontal? query and raise an AssertionError if the returned value does not match value.
Properties
  • .uicount: The DPOJET:SOURCEAutoset:HORizontal:UICount command.
  • .uivalue: The DPOJET:SOURCEAutoset:HORizontal:UIValue command.

uicount property 

uicount: DpojetSourceautosetHorizontalUicount

Return the DPOJET:SOURCEAutoset:HORizontal:UICount command.

Description
  • This command sets or queries the UICount for horizontal autoset.
Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:HORizontal:UICount? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UICount? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UICount value command.
SCPI Syntax 
- DPOJET:SOURCEAutoset:HORizontal:UICount <NR3>
- DPOJET:SOURCEAutoset:HORizontal:UICount?

uivalue property 

uivalue: DpojetSourceautosetHorizontalUivalue

Return the DPOJET:SOURCEAutoset:HORizontal:UIValue command.

Description
  • This command sets or queries the UI value for horizontal autoset.
Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:HORizontal:UIValue? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UIValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UIValue value command.
SCPI Syntax 
- DPOJET:SOURCEAutoset:HORizontal:UIValue <NR3>
- DPOJET:SOURCEAutoset:HORizontal:UIValue?

DpojetSourceautosetHorizontalUicount

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:SOURCEAutoset:HORizontal:UICount command.

Description
  • This command sets or queries the UICount for horizontal autoset.
Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:HORizontal:UICount? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UICount? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UICount value command.
SCPI Syntax 
- DPOJET:SOURCEAutoset:HORizontal:UICount <NR3>
- DPOJET:SOURCEAutoset:HORizontal:UICount?

DpojetSourceautosetHorizontalUivalue

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:SOURCEAutoset:HORizontal:UIValue command.

Description
  • This command sets or queries the UI value for horizontal autoset.
Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:HORizontal:UIValue? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UIValue? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:SOURCEAutoset:HORizontal:UIValue value command.
SCPI Syntax 
- DPOJET:SOURCEAutoset:HORizontal:UIValue <NR3>
- DPOJET:SOURCEAutoset:HORizontal:UIValue?

DpojetSourceautosetState

Bases: SCPICmdRead

The DPOJET:SOURCEAutoset:STATE command.

Description
  • This query-only command provides the Source Autoset status.
Usage
  • Using the .query() method will send the DPOJET:SOURCEAutoset:STATE? query.
  • Using the .verify(value) method will send the DPOJET:SOURCEAutoset:STATE? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:SOURCEAutoset:STATE?

DpojetState

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:STATE command.

Description
  • This command sets or queries the current measurement state of DPOJET.
Usage
  • Using the .query() method will send the DPOJET:STATE? query.
  • Using the .verify(value) method will send the DPOJET:STATE? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:STATE value command.
SCPI Syntax 
- DPOJET:STATE {RUN|SINGLE|RECALC|CLEAR|STOP}
- DPOJET:STATE?

DpojetTdcompensation

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:TDCOMPensation command.

Description
  • This command sets or queries the TD compensation state.
Usage
  • Using the .query() method will send the DPOJET:TDCOMPensation? query.
  • Using the .verify(value) method will send the DPOJET:TDCOMPensation? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:TDCOMPensation value command.
SCPI Syntax 
- DPOJET:TDCOMPensation {ON|OFF|1|0}
- DPOJET:TDCOMPensation?

DpojetUnittype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:UNITType command.

Description
  • This command sets or queries the current unit-type setting for DPOJET, either Unit Interval, or seconds.
Usage
  • Using the .query() method will send the DPOJET:UNITType? query.
  • Using the .verify(value) method will send the DPOJET:UNITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:UNITType value command.
SCPI Syntax 
- DPOJET:UNITType {UNITinterval|SEConds}
- DPOJET:UNITType?

DpojetVersion

Bases: SCPICmdRead

The DPOJET:VERsion command.

Description
  • This query-only command returns the current DPOJET version string.
Usage
  • Using the .query() method will send the DPOJET:VERsion? query.
  • Using the .verify(value) method will send the DPOJET:VERsion? query and raise an AssertionError if the returned value does not match value.
SCPI Syntax 
- DPOJET:VERsion?

DpojetVertunittype

Bases: SCPICmdWrite, SCPICmdRead

The DPOJET:VERTUNITType command.

Description
  • This command sets or queries the vertical Unit.
Usage
  • Using the .query() method will send the DPOJET:VERTUNITType? query.
  • Using the .verify(value) method will send the DPOJET:VERTUNITType? query and raise an AssertionError if the returned value does not match value.
  • Using the .write(value) method will send the DPOJET:VERTUNITType value command.
SCPI Syntax 
- DPOJET:VERTUNITType {UNITamplitude|VOLts}
- DPOJET:VERTUNITType?