plot ¶

The plot commands module.

These commands are used in the following models: TekScopePC

THIS FILE IS AUTO-GENERATED, IT SHOULD NOT BE MANUALLY MODIFIED.

Please report an issue if one is found.

Commands and Queries

- PLOT:ADDNew <QString>
- PLOT:DELete <QString>
- PLOT:LIST?
- PLOT:PLOT<x>:BATHtub:BER <NR1>
- PLOT:PLOT<x>:BATHtub:BER?
- PLOT:PLOT<x>:BATHtub:XAXISUnits {UNITIntervals|SECOnds}
- PLOT:PLOT<x>:BATHtub:XAXISUnits?
- PLOT:PLOT<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- PLOT:PLOT<x>:BITType?
- PLOT:PLOT<x>:EXPORTRaw?
- PLOT:PLOT<x>:EXTENDuis <NR1>
- PLOT:PLOT<x>:EXTENDuis?
- PLOT:PLOT<x>:EYERender {FAst|COMPlete}
- PLOT:PLOT<x>:EYERender?
- PLOT:PLOT<x>:IMDA:MEAS {VRMS|IRMS|PHASE|FREQuency|TRPWR|REPWR|APPPWR|TRPWRSUM|REPWRSUM|APPPWRSUM|DCPWR|INPWR|OUTPWR|EFFiciency|TOTALEFFiciency|INPWRSUM|OUTPWRSUM}
- PLOT:PLOT<x>:IMDA:MEAS?
- PLOT:PLOT<x>:IMDAPLOTDisplay {ALL|ONEPAIRVI|ONEPAIRV|ONEPAIRI|PHASEONE|PHASETWO|PHASETHREE|ABC|DQ0}
- PLOT:PLOT<x>:IMDAPLOTDisplay?
- PLOT:PLOT<x>:LABel:COLor <QString>
- PLOT:PLOT<x>:LABel:COLor?
- PLOT:PLOT<x>:LABel:FONT:BOLD {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:BOLD?
- PLOT:PLOT<x>:LABel:FONT:ITALic {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:ITALic?
- PLOT:PLOT<x>:LABel:FONT:SIZE <NR1>
- PLOT:PLOT<x>:LABel:FONT:SIZE?
- PLOT:PLOT<x>:LABel:FONT:TYPE <QString>
- PLOT:PLOT<x>:LABel:FONT:TYPE?
- PLOT:PLOT<x>:LABel:FONT:UNDERline {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:UNDERline?
- PLOT:PLOT<x>:LABel:NAMe <QString>
- PLOT:PLOT<x>:LABel:NAMe?
- PLOT:PLOT<x>:LABel:XPOS <NR3>
- PLOT:PLOT<x>:LABel:XPOS?
- PLOT:PLOT<x>:LABel:YPOS <NR3>
- PLOT:PLOT<x>:LABel:YPOS?
- PLOT:PLOT<x>:MASK?
- PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit {ON|OFF}
- PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit?
- PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM <NR3>
- PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM?
- PLOT:PLOT<x>:MASKOffset:PERCENTui:TO <NR3>
- PLOT:PLOT<x>:MASKOffset:PERCENTui:TO?
- PLOT:PLOT<x>:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- PLOT:PLOT<x>:NUMBins?
- PLOT:PLOT<x>:PTYPe {RMS|MAGNITUDE}
- PLOT:PLOT<x>:PTYPe?
- PLOT:PLOT<x>:RAILNUM RAIL<x>
- PLOT:PLOT<x>:RAILNUM?
- PLOT:PLOT<x>:SOUrce1 MEAS<x>
- PLOT:PLOT<x>:SOUrce1?
- PLOT:PLOT<x>:SPECtrum:BASE <NR1>
- PLOT:PLOT<x>:SPECtrum:BASE?
- PLOT:PLOT<x>:SPECtrum:DYNRange <NR3>
- PLOT:PLOT<x>:SPECtrum:DYNRange?
- PLOT:PLOT<x>:TYPe {NONE|BATHTUB|EYEDIAGRAM|HARMONICS|HISTOGRAM|IMDATIMETREND|IMDAACQTREND|INDUCTANCE|IVSINTEGRALV|MAGPROPERTY|PHASENOISE|PHASOR|SOA|SPECTRUM|SSCPROFILE|SWL|TIEHISTOGRAM|TIETIMETREND|TIESPECTRUM|TIMETREND|XY|XYZ}

Plot ¶

Bases: SCPICmdRead

The PLOT command tree.

Usage

Using the .query() method will send the PLOT? query.
Using the .verify(value) method will send the PLOT? query and raise an AssertionError if the returned value does not match value.

Properties

.addnew: The PLOT:ADDNew command.
.delete: The PLOT:DELete command.
.list: The PLOT:LIST command.
.plot: The PLOT:PLOT<x> command tree.

addnew `property` ¶

addnew: PlotAddnew

Return the PLOT:ADDNew command.

Description

This command adds the specified plot.

Usage

Using the .write(value) method will send the PLOT:ADDNew value command.

SCPI Syntax

- PLOT:ADDNew <QString>

Info

<QString> is the specified plot. The argument is of the form ‘PLOT‘, where ≥ 1.

delete `property` ¶

delete: PlotDelete

Return the PLOT:DELete command.

Description

This command deletes the specified plot.

Usage

Using the .write(value) method will send the PLOT:DELete value command.

SCPI Syntax

- PLOT:DELete <QString>

Info

<QString> is the specified plot. Argument is of the form ‘PLOT, where is ≥ 1).

list `property` ¶

list: PlotList

Return the PLOT:LIST command.

Description

This command lists all currently defined plots.

Usage

Using the .query() method will send the PLOT:LIST? query.
Using the .verify(value) method will send the PLOT:LIST? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- PLOT:LIST?

plot `property` ¶

plot: dict[int, PlotPlotItem]

Return the PLOT:PLOT<x> command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>? query.
Using the .verify(value) method will send the PLOT:PLOT<x>? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.bathtub: The PLOT:PLOT<x>:BATHtub command tree.
.bittype: The PLOT:PLOT<x>:BITType command.
.exportraw: The PLOT:PLOT<x>:EXPORTRaw command.
.extenduis: The PLOT:PLOT<x>:EXTENDuis command.
.eyerender: The PLOT:PLOT<x>:EYERender command.
.imda: The PLOT:PLOT<x>:IMDA command tree.
.imdaplotdisplay: The PLOT:PLOT<x>:IMDAPLOTDisplay command.
.label: The PLOT:PLOT<x>:LABel command tree.
.mask: The PLOT:PLOT<x>:MASK command.
.maskoffset: The PLOT:PLOT<x>:MASKOffset command tree.
.numbins: The PLOT:PLOT<x>:NUMBins command.
.ptype: The PLOT:PLOT<x>:PTYPe command.
.railnum: The PLOT:PLOT<x>:RAILNUM command.
.source1: The PLOT:PLOT<x>:SOUrce1 command.
.spectrum: The PLOT:PLOT<x>:SPECtrum command tree.
.type: The PLOT:PLOT<x>:TYPe command.

PlotAddnew ¶

Bases: SCPICmdWrite

The PLOT:ADDNew command.

Description

This command adds the specified plot.

Usage

Using the .write(value) method will send the PLOT:ADDNew value command.

SCPI Syntax

- PLOT:ADDNew <QString>

Info

<QString> is the specified plot. The argument is of the form ‘PLOT‘, where ≥ 1.

PlotDelete ¶

Bases: SCPICmdWrite

The PLOT:DELete command.

Description

This command deletes the specified plot.

Usage

Using the .write(value) method will send the PLOT:DELete value command.

SCPI Syntax

- PLOT:DELete <QString>

Info

<QString> is the specified plot. Argument is of the form ‘PLOT, where is ≥ 1).

PlotList ¶

Bases: SCPICmdRead

The PLOT:LIST command.

Description

This command lists all currently defined plots.

Usage

Using the .query() method will send the PLOT:LIST? query.
Using the .verify(value) method will send the PLOT:LIST? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- PLOT:LIST?

PlotPlotItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The PLOT:PLOT<x> command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>? query.
Using the .verify(value) method will send the PLOT:PLOT<x>? query and raise an AssertionError if the returned value does not match value.

Properties

.bathtub: The PLOT:PLOT<x>:BATHtub command tree.
.bittype: The PLOT:PLOT<x>:BITType command.
.exportraw: The PLOT:PLOT<x>:EXPORTRaw command.
.extenduis: The PLOT:PLOT<x>:EXTENDuis command.
.eyerender: The PLOT:PLOT<x>:EYERender command.
.imda: The PLOT:PLOT<x>:IMDA command tree.
.imdaplotdisplay: The PLOT:PLOT<x>:IMDAPLOTDisplay command.
.label: The PLOT:PLOT<x>:LABel command tree.
.mask: The PLOT:PLOT<x>:MASK command.
.maskoffset: The PLOT:PLOT<x>:MASKOffset command tree.
.numbins: The PLOT:PLOT<x>:NUMBins command.
.ptype: The PLOT:PLOT<x>:PTYPe command.
.railnum: The PLOT:PLOT<x>:RAILNUM command.
.source1: The PLOT:PLOT<x>:SOUrce1 command.
.spectrum: The PLOT:PLOT<x>:SPECtrum command tree.
.type: The PLOT:PLOT<x>:TYPe command.

bathtub `property` ¶

bathtub: PlotPlotItemBathtub

Return the PLOT:PLOT<x>:BATHtub command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BATHtub? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BATHtub? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.ber: The PLOT:PLOT<x>:BATHtub:BER command.
.xaxisunits: The PLOT:PLOT<x>:BATHtub:XAXISUnits command.

bittype `property` ¶

bittype: PlotPlotItemBittype

Return the PLOT:PLOT<x>:BITType command.

Description

This command sets or queries the bit type to display for the specified eye diagram plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BITType? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BITType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:BITType value command.

SCPI Syntax

- PLOT:PLOT<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- PLOT:PLOT<x>:BITType?

Info

PLOT<x> is the plot number.
ALLBits sets the eye diagram plot to show both transition and nontransition bits.
TRANSition sets the eye diagram plot to show only bits where a logic level transition occurs.
NONTRANsition sets the eye diagram plot to show only bits where no logic level transition occurs.

exportraw `property` ¶

exportraw: PlotPlotItemExportraw

Return the PLOT:PLOT<x>:EXPORTRaw command.

Description

This command returns a binary stream of double values containing the x,y and hits value. Use this command along with MEASUREMENT:ADDMEAS TIE, PLOT:PLOT1:TYPE EYEDIAGRAM, DISplay:SELect:VIEW plotview1 to export the eye diagram plot data.

Usage

Using the .query() method will send the PLOT:PLOT<x>:EXPORTRaw? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:EXPORTRaw? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- PLOT:PLOT<x>:EXPORTRaw?

extenduis `property` ¶

extenduis: PlotPlotItemExtenduis

Return the PLOT:PLOT<x>:EXTENDuis command.

Description

This command sets or queries number of UIs surrounding the eye boundary UIs that are used for fast eye rendering.

Usage

Using the .query() method will send the PLOT:PLOT<x>:EXTENDuis? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:EXTENDuis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:EXTENDuis value command.

SCPI Syntax

- PLOT:PLOT<x>:EXTENDuis <NR1>
- PLOT:PLOT<x>:EXTENDuis?

Info

PLOT<x> is the plot number.
<NR1> is the number of surrounding UIs.

eyerender `property` ¶

eyerender: PlotPlotItemEyerender

Return the PLOT:PLOT<x>:EYERender command.

Description

This command sets or queries the eye rendering method for the specified plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:EYERender? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:EYERender? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:EYERender value command.

SCPI Syntax

- PLOT:PLOT<x>:EYERender {FAst|COMPlete}
- PLOT:PLOT<x>:EYERender?

Info

PLOT<x> is the plot number.
FAst sets the eye rendering method to fast.
COMPlete sets the eye rendering method to complete.

imda `property` ¶

imda: PlotPlotItemImda

Return the PLOT:PLOT<x>:IMDA command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:IMDA? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:IMDA? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Sub-properties

.meas: The PLOT:PLOT<x>:IMDA:MEAS command.

imdaplotdisplay `property` ¶

imdaplotdisplay: PlotPlotItemImdaplotdisplay

Return the PLOT:PLOT<x>:IMDAPLOTDisplay command.

Description

This command sets or returns the IMDA time trend and acq trend plot display configuration.

Usage

Using the .query() method will send the PLOT:PLOT<x>:IMDAPLOTDisplay? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:IMDAPLOTDisplay? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:IMDAPLOTDisplay value command.

SCPI Syntax

- PLOT:PLOT<x>:IMDAPLOTDisplay {ALL|ONEPAIRVI|ONEPAIRV|ONEPAIRI|PHASEONE|PHASETWO|PHASETHREE|ABC|DQ0}
- PLOT:PLOT<x>:IMDAPLOTDisplay?

Info

PLOT<x> is the plot number.
ALL sets the IMDA time trend and acq trend plot display configuration to ALL.
ONEPAIRVI sets the IMDA time trend and acq trend plot display configuration to ONEPAIRVI.
ONEPAIRV sets the IMDA time trend and acq trend plot display configuration to ONEPAIRV.
ONEPAIRI sets the IMDA time trend and acq trend plot display configuration to ONEPAIRI.
PHASEONE sets the IMDA time trend and acq trend plot display configuration to PHASEONE.
PHASETWO sets the IMDA time trend and acq trend plot display configuration to PHASETWO.
PHASETHREE sets the IMDA time trend and acq trend plot display configuration to PHASETHREE.
ABC sets the IMDA time trend plot display to ABC.
DQ0 sets the IMDA time trend plot display to DQ0.

label `property` ¶

label: PlotPlotItemLabel

Return the PLOT:PLOT<x>:LABel command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.color: The PLOT:PLOT<x>:LABel:COLor command.
.font: The PLOT:PLOT<x>:LABel:FONT command tree.
.name: The PLOT:PLOT<x>:LABel:NAMe command.
.xpos: The PLOT:PLOT<x>:LABel:XPOS command.
.ypos: The PLOT:PLOT<x>:LABel:YPOS command.

mask `property` ¶

mask: PlotPlotItemMask

Return the PLOT:PLOT<x>:MASK command.

Description

This command returns the name of the mask test associated with the specified eye diagram plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASK? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- PLOT:PLOT<x>:MASK?

Info

PLOT<x> is the plot number.

maskoffset `property` ¶

maskoffset: PlotPlotItemMaskoffset

Return the PLOT:PLOT<x>:MASKOffset command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Sub-properties

.horizontal: The PLOT:PLOT<x>:MASKOffset:HORizontal command tree.
.percentui: The PLOT:PLOT<x>:MASKOffset:PERCENTui command tree.

numbins `property` ¶

numbins: PlotPlotItemNumbins

Return the PLOT:PLOT<x>:NUMBins command.

Description

This command sets or queries the current histogram resolution.

Usage

Using the .query() method will send the PLOT:PLOT<x>:NUMBins? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:NUMBins? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:NUMBins value command.

SCPI Syntax

- PLOT:PLOT<x>:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- PLOT:PLOT<x>:NUMBins?

Info

TWENtyfive sets the number of bins to 25.
FIFTY sets the number of bins to 50.
HUNdred sets the number of bins to 100.
TWOFifty sets the number of bins to 250.
FIVEHundred sets the number of bins to 500.
TWOThousand sets the number of bins to 2000.
MAXimum sets the number of bins to the maximum value.

ptype `property` ¶

ptype: PlotPlotItemPtype

Return the PLOT:PLOT<x>:PTYPe command.

Description

This command sets or returns the phasor type of the phasor diagram plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:PTYPe? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:PTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:PTYPe value command.

SCPI Syntax

- PLOT:PLOT<x>:PTYPe {RMS|MAGNITUDE}
- PLOT:PLOT<x>:PTYPe?

Info

PLOT<x> is the plot number.
RMS sets the phasor type to RMS.
MAGNITUDE sets the phasor type to MAGNITUDE.

railnum `property` ¶

railnum: PlotPlotItemRailnum

Return the PLOT:PLOT<x>:RAILNUM command.

Description

Sets the DPM histogram source.

Usage

Using the .query() method will send the PLOT:PLOT<x>:RAILNUM? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:RAILNUM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:RAILNUM value command.

SCPI Syntax

- PLOT:PLOT<x>:RAILNUM RAIL<x>
- PLOT:PLOT<x>:RAILNUM?

Info

PLOT<x> is the plot number.
Rail<x> is the rail number. x has a minimum of 1 and a maximum of 7.

source1 `property` ¶

source1: PlotPlotItemSource1

Return the PLOT:PLOT<x>:SOUrce1 command.

Description

This command sets or queries the plot source.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SOUrce1? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:SOUrce1 value command.

SCPI Syntax

- PLOT:PLOT<x>:SOUrce1 MEAS<x>
- PLOT:PLOT<x>:SOUrce1?

Info

MEAS<x> is the specified measurement source for the specified plot.

spectrum `property` ¶

spectrum: PlotPlotItemSpectrum

Return the PLOT:PLOT<x>:SPECtrum command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SPECtrum? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SPECtrum? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.base: The PLOT:PLOT<x>:SPECtrum:BASE command.
.dynrange: The PLOT:PLOT<x>:SPECtrum:DYNRange command.

type `property` ¶

type: PlotPlotItemType

Return the PLOT:PLOT<x>:TYPe command.

Description

This command sets or returns the current plot type of the specified plot.

Usage

Using the .write(value) method will send the PLOT:PLOT<x>:TYPe value command.

SCPI Syntax

- PLOT:PLOT<x>:TYPe {NONE|BATHTUB|EYEDIAGRAM|HARMONICS|HISTOGRAM|IMDATIMETREND|IMDAACQTREND|INDUCTANCE|IVSINTEGRALV|MAGPROPERTY|PHASENOISE|PHASOR|SOA|SPECTRUM|SSCPROFILE|SWL|TIEHISTOGRAM|TIETIMETREND|TIESPECTRUM|TIMETREND|XY|XYZ}

Info

<x> is the plot number. This is the equivalent of the number shown on a plot heading in the UI.
NONE does not create a plot.
BATHTUB creates a bathtub plot.
EYEDIAGRAM creates an eye diagram. This plot type is not available on a 4 Series MSO instrument.
HARMONICS creates a harmonics bar graph.
HISTOGRAM creates a histogram plot.
IMDATIMETREND creates a IMDA time trend plot. This plot type requires option IMDA.
IMDAACQTREND creates a IMDA acq trend plot. This plot type requires option IMDA.
INDUCTANCE creates a inductance plot.
IVSINTEGRALV creates a I vs. ∫V plot.
PHASENOISE creates a phase noise plot.
PHASOR creates the Phasor Diagram. This plot type requires option 5-DPM on MSO58/56 series instruments.
MAGPROPERTY creates a BH curve.
SOA creates an SOA plot.
SPECTRUM creates a spectrum plot.
SSCPROFILE creates a SSC profile plot.
SWL creates a Switching Loss plot.
TIEHISTOGRAM creates a TIE histogram plot.
TIESPECTRUM creates a TIE spectrum plot.
TIETIMETREND creates a TIE time trend plot.
TIMETREND creates a time trend plot.
XY creates a XY plot.
XYZ creates a XYZ plot.

PlotPlotItemBathtub ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:BATHtub command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BATHtub? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BATHtub? query and raise an AssertionError if the returned value does not match value.

Properties

.ber: The PLOT:PLOT<x>:BATHtub:BER command.
.xaxisunits: The PLOT:PLOT<x>:BATHtub:XAXISUnits command.

ber `property` ¶

ber: PlotPlotItemBathtubBer

Return the PLOT:PLOT<x>:BATHtub:BER command.

Description

This command sets or queries the bathtub BER value.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BATHtub:BER? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BATHtub:BER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:BATHtub:BER value command.

SCPI Syntax

- PLOT:PLOT<x>:BATHtub:BER <NR1>
- PLOT:PLOT<x>:BATHtub:BER?

Info

<NR1> is the bathtub BER value.

xaxisunits `property` ¶

xaxisunits: PlotPlotItemBathtubXaxisunits

Return the PLOT:PLOT<x>:BATHtub:XAXISUnits command.

Description

This command sets or queries the X-Axis unit, either unit intervals or seconds.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BATHtub:XAXISUnits? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BATHtub:XAXISUnits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:BATHtub:XAXISUnits value command.

SCPI Syntax

- PLOT:PLOT<x>:BATHtub:XAXISUnits {UNITIntervals|SECOnds}
- PLOT:PLOT<x>:BATHtub:XAXISUnits?

Info

UNITIntervals specifies units as unit intervals.
SECOnds specifies units as seconds.

PlotPlotItemBathtubBer ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:BATHtub:BER command.

Description

This command sets or queries the bathtub BER value.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BATHtub:BER? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BATHtub:BER? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:BATHtub:BER value command.

SCPI Syntax

- PLOT:PLOT<x>:BATHtub:BER <NR1>
- PLOT:PLOT<x>:BATHtub:BER?

Info

<NR1> is the bathtub BER value.

PlotPlotItemBathtubXaxisunits ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:BATHtub:XAXISUnits command.

Description

This command sets or queries the X-Axis unit, either unit intervals or seconds.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BATHtub:XAXISUnits? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BATHtub:XAXISUnits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:BATHtub:XAXISUnits value command.

SCPI Syntax

- PLOT:PLOT<x>:BATHtub:XAXISUnits {UNITIntervals|SECOnds}
- PLOT:PLOT<x>:BATHtub:XAXISUnits?

Info

UNITIntervals specifies units as unit intervals.
SECOnds specifies units as seconds.

PlotPlotItemBittype ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:BITType command.

Description

This command sets or queries the bit type to display for the specified eye diagram plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:BITType? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:BITType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:BITType value command.

SCPI Syntax

- PLOT:PLOT<x>:BITType {ALLBits|TRANSition|NONTRANsition}
- PLOT:PLOT<x>:BITType?

Info

PLOT<x> is the plot number.
ALLBits sets the eye diagram plot to show both transition and nontransition bits.
TRANSition sets the eye diagram plot to show only bits where a logic level transition occurs.
NONTRANsition sets the eye diagram plot to show only bits where no logic level transition occurs.

PlotPlotItemExportraw ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:EXPORTRaw command.

Description

This command returns a binary stream of double values containing the x,y and hits value. Use this command along with MEASUREMENT:ADDMEAS TIE, PLOT:PLOT1:TYPE EYEDIAGRAM, DISplay:SELect:VIEW plotview1 to export the eye diagram plot data.

Usage

Using the .query() method will send the PLOT:PLOT<x>:EXPORTRaw? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:EXPORTRaw? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- PLOT:PLOT<x>:EXPORTRaw?

PlotPlotItemExtenduis ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:EXTENDuis command.

Description

This command sets or queries number of UIs surrounding the eye boundary UIs that are used for fast eye rendering.

Usage

Using the .query() method will send the PLOT:PLOT<x>:EXTENDuis? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:EXTENDuis? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:EXTENDuis value command.

SCPI Syntax

- PLOT:PLOT<x>:EXTENDuis <NR1>
- PLOT:PLOT<x>:EXTENDuis?

Info

PLOT<x> is the plot number.
<NR1> is the number of surrounding UIs.

PlotPlotItemEyerender ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:EYERender command.

Description

This command sets or queries the eye rendering method for the specified plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:EYERender? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:EYERender? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:EYERender value command.

SCPI Syntax

- PLOT:PLOT<x>:EYERender {FAst|COMPlete}
- PLOT:PLOT<x>:EYERender?

Info

PLOT<x> is the plot number.
FAst sets the eye rendering method to fast.
COMPlete sets the eye rendering method to complete.

PlotPlotItemImda ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:IMDA command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:IMDA? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:IMDA? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Properties

.meas: The PLOT:PLOT<x>:IMDA:MEAS command.

meas `property` ¶

meas: PlotPlotItemImdaMeas

Return the PLOT:PLOT<x>:IMDA:MEAS command.

Description

This command sets or returns the measurement selection of trend plot and acq trend plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:IMDA:MEAS? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:IMDA:MEAS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:IMDA:MEAS value command.

SCPI Syntax

- PLOT:PLOT<x>:IMDA:MEAS {VRMS|IRMS|PHASE|FREQuency|TRPWR|REPWR|APPPWR|TRPWRSUM|REPWRSUM|APPPWRSUM|DCPWR|INPWR|OUTPWR|EFFiciency|TOTALEFFiciency|INPWRSUM|OUTPWRSUM}
- PLOT:PLOT<x>:IMDA:MEAS?

Info

PLOT<x> is the plot number.
VRMS sets the IMDA measurement selection to VRMS.
IRMS sets the IMDA measurement selection to IRMS.
PHASE sets the IMDA measurement selection to PHASE.
FREQuency sets the IMDA measurement selection to FREQuency.
TRPWR sets the IMDA measurement selection to TRPWR.
REPWR sets the IMDA measurement selection to REPWR.
APPPWR sets the IMDA measurement selection to APPPWR.
TRPWRSUM sets the IMDA measurement selection to TRPWRSUM.
REPWRSUM sets the IMDA measurement selection to REPWRSUM.
APPPWRSUM sets the IMDA measurement selection to APPPWRSUM.
DCPWR sets the IMDA measurement selection to DCPWR. This selection is applicable only for acq trend plots.
INPWR sets the IMDA measurement selection to INPWR. This selection is applicable only for acq trend plots.
OUTPWR sets the IMDA measurement selection to OUTPWR. This selection is applicable only for acq trend plots.
EFFiciency sets the IMDA measurement selection to EFFiciency.
TOTALEFFiciency sets the IMDA measurement selection to TOTALEFFiciency. This selection is applicable only for acq trend plots.
INPWRSUM sets the IMDA measurement selection to INPWRSUM. This selection is applicable only for acq trend plots.
OUTPWRSUM sets the IMDA measurement selection to OUTPWRSUM. This selection is applicable only for acq trend plots.

PlotPlotItemImdaMeas ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:IMDA:MEAS command.

Description

This command sets or returns the measurement selection of trend plot and acq trend plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:IMDA:MEAS? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:IMDA:MEAS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:IMDA:MEAS value command.

SCPI Syntax

- PLOT:PLOT<x>:IMDA:MEAS {VRMS|IRMS|PHASE|FREQuency|TRPWR|REPWR|APPPWR|TRPWRSUM|REPWRSUM|APPPWRSUM|DCPWR|INPWR|OUTPWR|EFFiciency|TOTALEFFiciency|INPWRSUM|OUTPWRSUM}
- PLOT:PLOT<x>:IMDA:MEAS?

Info

PLOT<x> is the plot number.
VRMS sets the IMDA measurement selection to VRMS.
IRMS sets the IMDA measurement selection to IRMS.
PHASE sets the IMDA measurement selection to PHASE.
FREQuency sets the IMDA measurement selection to FREQuency.
TRPWR sets the IMDA measurement selection to TRPWR.
REPWR sets the IMDA measurement selection to REPWR.
APPPWR sets the IMDA measurement selection to APPPWR.
TRPWRSUM sets the IMDA measurement selection to TRPWRSUM.
REPWRSUM sets the IMDA measurement selection to REPWRSUM.
APPPWRSUM sets the IMDA measurement selection to APPPWRSUM.
DCPWR sets the IMDA measurement selection to DCPWR. This selection is applicable only for acq trend plots.
INPWR sets the IMDA measurement selection to INPWR. This selection is applicable only for acq trend plots.
OUTPWR sets the IMDA measurement selection to OUTPWR. This selection is applicable only for acq trend plots.
EFFiciency sets the IMDA measurement selection to EFFiciency.
TOTALEFFiciency sets the IMDA measurement selection to TOTALEFFiciency. This selection is applicable only for acq trend plots.
INPWRSUM sets the IMDA measurement selection to INPWRSUM. This selection is applicable only for acq trend plots.
OUTPWRSUM sets the IMDA measurement selection to OUTPWRSUM. This selection is applicable only for acq trend plots.

PlotPlotItemImdaplotdisplay ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:IMDAPLOTDisplay command.

Description

This command sets or returns the IMDA time trend and acq trend plot display configuration.

Usage

Using the .query() method will send the PLOT:PLOT<x>:IMDAPLOTDisplay? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:IMDAPLOTDisplay? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:IMDAPLOTDisplay value command.

SCPI Syntax

- PLOT:PLOT<x>:IMDAPLOTDisplay {ALL|ONEPAIRVI|ONEPAIRV|ONEPAIRI|PHASEONE|PHASETWO|PHASETHREE|ABC|DQ0}
- PLOT:PLOT<x>:IMDAPLOTDisplay?

Info

PLOT<x> is the plot number.
ALL sets the IMDA time trend and acq trend plot display configuration to ALL.
ONEPAIRVI sets the IMDA time trend and acq trend plot display configuration to ONEPAIRVI.
ONEPAIRV sets the IMDA time trend and acq trend plot display configuration to ONEPAIRV.
ONEPAIRI sets the IMDA time trend and acq trend plot display configuration to ONEPAIRI.
PHASEONE sets the IMDA time trend and acq trend plot display configuration to PHASEONE.
PHASETWO sets the IMDA time trend and acq trend plot display configuration to PHASETWO.
PHASETHREE sets the IMDA time trend and acq trend plot display configuration to PHASETHREE.
ABC sets the IMDA time trend plot display to ABC.
DQ0 sets the IMDA time trend plot display to DQ0.

PlotPlotItemLabel ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:LABel command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel? query and raise an AssertionError if the returned value does not match value.

Properties

.color: The PLOT:PLOT<x>:LABel:COLor command.
.font: The PLOT:PLOT<x>:LABel:FONT command tree.
.name: The PLOT:PLOT<x>:LABel:NAMe command.
.xpos: The PLOT:PLOT<x>:LABel:XPOS command.
.ypos: The PLOT:PLOT<x>:LABel:YPOS command.

color `property` ¶

color: PlotPlotItemLabelColor

Return the PLOT:PLOT<x>:LABel:COLor command.

Description

This command sets or queries the color of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:COLor? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:COLor? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:COLor value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:COLor <QString>
- PLOT:PLOT<x>:LABel:COLor?

Info

<QString> is the label color. The default color is specified by a quoted empty string, and is the only available color.

font `property` ¶

font: PlotPlotItemLabelFont

Return the PLOT:PLOT<x>:LABel:FONT command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.bold: The PLOT:PLOT<x>:LABel:FONT:BOLD command.
.italic: The PLOT:PLOT<x>:LABel:FONT:ITALic command.
.size: The PLOT:PLOT<x>:LABel:FONT:SIZE command.
.type: The PLOT:PLOT<x>:LABel:FONT:TYPE command.
.underline: The PLOT:PLOT<x>:LABel:FONT:UNDERline command.

name `property` ¶

name: PlotPlotItemLabelName

Return the PLOT:PLOT<x>:LABel:NAMe command.

Description

This command sets or queries the specified trend’s label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:NAMe? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:NAMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:NAMe value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:NAMe <QString>
- PLOT:PLOT<x>:LABel:NAMe?

Info

<QString> is the label.

xpos `property` ¶

xpos: PlotPlotItemLabelXpos

Return the PLOT:PLOT<x>:LABel:XPOS command.

Description

This command sets or queries the x-position of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:XPOS? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:XPOS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:XPOS value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:XPOS <NR3>
- PLOT:PLOT<x>:LABel:XPOS?

Info

<NR3> is the y-position, in pixels relative to the left edge of the display, of the label.

ypos `property` ¶

ypos: PlotPlotItemLabelYpos

Return the PLOT:PLOT<x>:LABel:YPOS command.

Description

This command sets or queries the y-position of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:YPOS? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:YPOS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:YPOS value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:YPOS <NR3>
- PLOT:PLOT<x>:LABel:YPOS?

Info

<NR3> is the x-position, in pixels relative to the baseline of the waveform, of the label.

PlotPlotItemLabelColor ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:COLor command.

Description

This command sets or queries the color of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:COLor? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:COLor? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:COLor value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:COLor <QString>
- PLOT:PLOT<x>:LABel:COLor?

Info

<QString> is the label color. The default color is specified by a quoted empty string, and is the only available color.

PlotPlotItemLabelFont ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:LABel:FONT command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT? query and raise an AssertionError if the returned value does not match value.

Properties

.bold: The PLOT:PLOT<x>:LABel:FONT:BOLD command.
.italic: The PLOT:PLOT<x>:LABel:FONT:ITALic command.
.size: The PLOT:PLOT<x>:LABel:FONT:SIZE command.
.type: The PLOT:PLOT<x>:LABel:FONT:TYPE command.
.underline: The PLOT:PLOT<x>:LABel:FONT:UNDERline command.

bold `property` ¶

bold: PlotPlotItemLabelFontBold

Return the PLOT:PLOT<x>:LABel:FONT:BOLD command.

Description

This command sets or queries the bold state of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:BOLD? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:BOLD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:BOLD value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:BOLD {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:BOLD?

Info

<NR1> = 0 disables bold font; any other value turns this feature on.
OFF disables bold font.
ON enables bold font.

italic `property` ¶

italic: PlotPlotItemLabelFontItalic

Return the PLOT:PLOT<x>:LABel:FONT:ITALic command.

Description

This command sets or queries the italic state of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:ITALic? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:ITALic? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:ITALic value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:ITALic {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:ITALic?

Info

<NR1> = 0 disables italic font; any other value turns this feature on.
OFF disables italic font.
ON enables italic font.

size `property` ¶

size: PlotPlotItemLabelFontSize

Return the PLOT:PLOT<x>:LABel:FONT:SIZE command.

Description

This command sets or queries the font size of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:SIZE? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:SIZE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:SIZE value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:SIZE <NR1>
- PLOT:PLOT<x>:LABel:FONT:SIZE?

Info

<NR1> is the font size.

type `property` ¶

type: PlotPlotItemLabelFontType

Return the PLOT:PLOT<x>:LABel:FONT:TYPE command.

Description

This command sets or queries the font type of the specified trend label, such as Arial or Times New Roman. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:TYPE? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:TYPE value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:TYPE <QString>
- PLOT:PLOT<x>:LABel:FONT:TYPE?

Info

<QString> is the font type: Times New Roman, Arial, Frutiger LT Std 55 Roman, DejaVu Sans, DejaVu Sans Mono, Frutiger LT Std, Monospace, Sans Serif, Serif, Ubuntu, Ubuntu Condensed, and Ubuntu Mono.

underline `property` ¶

underline: PlotPlotItemLabelFontUnderline

Return the PLOT:PLOT<x>:LABel:FONT:UNDERline command.

Description

This command sets or queries the underline state of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:UNDERline? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:UNDERline? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:UNDERline value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:UNDERline {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:UNDERline?

Info

<NR1> = 0 disables underline font; any other value turns this feature on.
OFF disables underline font.
ON enables underline font.

PlotPlotItemLabelFontBold ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:FONT:BOLD command.

Description

This command sets or queries the bold state of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:BOLD? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:BOLD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:BOLD value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:BOLD {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:BOLD?

Info

<NR1> = 0 disables bold font; any other value turns this feature on.
OFF disables bold font.
ON enables bold font.

PlotPlotItemLabelFontItalic ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:FONT:ITALic command.

Description

This command sets or queries the italic state of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:ITALic? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:ITALic? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:ITALic value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:ITALic {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:ITALic?

Info

<NR1> = 0 disables italic font; any other value turns this feature on.
OFF disables italic font.
ON enables italic font.

PlotPlotItemLabelFontSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:FONT:SIZE command.

Description

This command sets or queries the font size of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:SIZE? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:SIZE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:SIZE value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:SIZE <NR1>
- PLOT:PLOT<x>:LABel:FONT:SIZE?

Info

<NR1> is the font size.

PlotPlotItemLabelFontType ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:FONT:TYPE command.

Description

This command sets or queries the font type of the specified trend label, such as Arial or Times New Roman. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:TYPE? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:TYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:TYPE value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:TYPE <QString>
- PLOT:PLOT<x>:LABel:FONT:TYPE?

Info

<QString> is the font type: Times New Roman, Arial, Frutiger LT Std 55 Roman, DejaVu Sans, DejaVu Sans Mono, Frutiger LT Std, Monospace, Sans Serif, Serif, Ubuntu, Ubuntu Condensed, and Ubuntu Mono.

PlotPlotItemLabelFontUnderline ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:FONT:UNDERline command.

Description

This command sets or queries the underline state of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:FONT:UNDERline? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:FONT:UNDERline? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:FONT:UNDERline value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:FONT:UNDERline {ON|OFF|<NR1>}
- PLOT:PLOT<x>:LABel:FONT:UNDERline?

Info

<NR1> = 0 disables underline font; any other value turns this feature on.
OFF disables underline font.
ON enables underline font.

PlotPlotItemLabelName ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:NAMe command.

Description

This command sets or queries the specified trend’s label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:NAMe? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:NAMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:NAMe value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:NAMe <QString>
- PLOT:PLOT<x>:LABel:NAMe?

Info

<QString> is the label.

PlotPlotItemLabelXpos ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:XPOS command.

Description

This command sets or queries the x-position of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:XPOS? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:XPOS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:XPOS value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:XPOS <NR3>
- PLOT:PLOT<x>:LABel:XPOS?

Info

<NR3> is the y-position, in pixels relative to the left edge of the display, of the label.

PlotPlotItemLabelYpos ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:LABel:YPOS command.

Description

This command sets or queries the y-position of the specified trend label. This command/query only applies to Time Trend plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:LABel:YPOS? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:LABel:YPOS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:LABel:YPOS value command.

SCPI Syntax

- PLOT:PLOT<x>:LABel:YPOS <NR3>
- PLOT:PLOT<x>:LABel:YPOS?

Info

<NR3> is the x-position, in pixels relative to the baseline of the waveform, of the label.

PlotPlotItemMask ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:MASK command.

Description

This command returns the name of the mask test associated with the specified eye diagram plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASK? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASK? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- PLOT:PLOT<x>:MASK?

Info

PLOT<x> is the plot number.

PlotPlotItemMaskoffset ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:MASKOffset command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Properties

.horizontal: The PLOT:PLOT<x>:MASKOffset:HORizontal command tree.
.percentui: The PLOT:PLOT<x>:MASKOffset:PERCENTui command tree.

horizontal `property` ¶

horizontal: PlotPlotItemMaskoffsetHorizontal

Return the PLOT:PLOT<x>:MASKOffset:HORizontal command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:HORizontal? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:HORizontal? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Sub-properties

.autofit: The PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit command.

percentui `property` ¶

percentui: PlotPlotItemMaskoffsetPercentui

Return the PLOT:PLOT<x>:MASKOffset:PERCENTui command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Sub-properties

.from: The PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM command.
.to: The PLOT:PLOT<x>:MASKOffset:PERCENTui:TO command.

PlotPlotItemMaskoffsetHorizontal ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:MASKOffset:HORizontal command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:HORizontal? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:HORizontal? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Properties

.autofit: The PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit command.

autofit `property` ¶

autofit: PlotPlotItemMaskoffsetHorizontalAutofit

Return the PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit command.

Description

This command enables or disables eye mask autofit in the specified plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit value command.

SCPI Syntax

- PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit {ON|OFF}
- PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit?

Info

PLOT<x> is the plot number.
ON enables eye mask autofit.
OFF disables eye mask autofit.

PlotPlotItemMaskoffsetHorizontalAutofit ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit command.

Description

This command enables or disables eye mask autofit in the specified plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit value command.

SCPI Syntax

- PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit {ON|OFF}
- PLOT:PLOT<x>:MASKOffset:HORizontal:AUTOfit?

Info

PLOT<x> is the plot number.
ON enables eye mask autofit.
OFF disables eye mask autofit.

PlotPlotItemMaskoffsetPercentui ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:MASKOffset:PERCENTui command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui? query and raise an AssertionError if the returned value does not match value.

Info

PLOT<x> is the plot number.

Properties

.from: The PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM command.
.to: The PLOT:PLOT<x>:MASKOffset:PERCENTui:TO command.

from_ `property` ¶

from_: PlotPlotItemMaskoffsetPercentuiFrom

Return the PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM command.

Description

This command sets or queries the allowed range for the mask to move in the left direction. Only applies to eye diagram plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM value command.

SCPI Syntax

- PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM <NR3>
- PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM?

Info

PLOT<x> is the plot number.
<NR3> is the allowed range in percentage for the mask to move in the left direction.

to `property` ¶

to: PlotPlotItemMaskoffsetPercentuiTo

Return the PLOT:PLOT<x>:MASKOffset:PERCENTui:TO command.

Description

This command sets or queries the allowed range for the mask to move in the right direction. Only applies to eye diagram plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:TO? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:TO? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:TO value command.

SCPI Syntax

- PLOT:PLOT<x>:MASKOffset:PERCENTui:TO <NR3>
- PLOT:PLOT<x>:MASKOffset:PERCENTui:TO?

Info

PLOT<x> is the plot number.
<NR3> is the allowed range in percentage for the mask to move in the right direction.

PlotPlotItemMaskoffsetPercentuiFrom ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM command.

Description

This command sets or queries the allowed range for the mask to move in the left direction. Only applies to eye diagram plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM value command.

SCPI Syntax

- PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM <NR3>
- PLOT:PLOT<x>:MASKOffset:PERCENTui:FROM?

Info

PLOT<x> is the plot number.
<NR3> is the allowed range in percentage for the mask to move in the left direction.

PlotPlotItemMaskoffsetPercentuiTo ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:MASKOffset:PERCENTui:TO command.

Description

This command sets or queries the allowed range for the mask to move in the right direction. Only applies to eye diagram plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:TO? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:TO? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:MASKOffset:PERCENTui:TO value command.

SCPI Syntax

- PLOT:PLOT<x>:MASKOffset:PERCENTui:TO <NR3>
- PLOT:PLOT<x>:MASKOffset:PERCENTui:TO?

Info

PLOT<x> is the plot number.
<NR3> is the allowed range in percentage for the mask to move in the right direction.

PlotPlotItemNumbins ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:NUMBins command.

Description

This command sets or queries the current histogram resolution.

Usage

Using the .query() method will send the PLOT:PLOT<x>:NUMBins? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:NUMBins? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:NUMBins value command.

SCPI Syntax

- PLOT:PLOT<x>:NUMBins {TWENtyfive|FIFTY|HUNdred|TWOFifty|FIVEHundred|TWOThousand|MAXimum}
- PLOT:PLOT<x>:NUMBins?

Info

TWENtyfive sets the number of bins to 25.
FIFTY sets the number of bins to 50.
HUNdred sets the number of bins to 100.
TWOFifty sets the number of bins to 250.
FIVEHundred sets the number of bins to 500.
TWOThousand sets the number of bins to 2000.
MAXimum sets the number of bins to the maximum value.

PlotPlotItemPtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:PTYPe command.

Description

This command sets or returns the phasor type of the phasor diagram plot.

Usage

Using the .query() method will send the PLOT:PLOT<x>:PTYPe? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:PTYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:PTYPe value command.

SCPI Syntax

- PLOT:PLOT<x>:PTYPe {RMS|MAGNITUDE}
- PLOT:PLOT<x>:PTYPe?

Info

PLOT<x> is the plot number.
RMS sets the phasor type to RMS.
MAGNITUDE sets the phasor type to MAGNITUDE.

PlotPlotItemRailnum ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:RAILNUM command.

Description

Sets the DPM histogram source.

Usage

Using the .query() method will send the PLOT:PLOT<x>:RAILNUM? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:RAILNUM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:RAILNUM value command.

SCPI Syntax

- PLOT:PLOT<x>:RAILNUM RAIL<x>
- PLOT:PLOT<x>:RAILNUM?

Info

PLOT<x> is the plot number.
Rail<x> is the rail number. x has a minimum of 1 and a maximum of 7.

PlotPlotItemSource1 ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:SOUrce1 command.

Description

This command sets or queries the plot source.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SOUrce1? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SOUrce1? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:SOUrce1 value command.

SCPI Syntax

- PLOT:PLOT<x>:SOUrce1 MEAS<x>
- PLOT:PLOT<x>:SOUrce1?

Info

MEAS<x> is the specified measurement source for the specified plot.

PlotPlotItemSpectrum ¶

Bases: SCPICmdRead

The PLOT:PLOT<x>:SPECtrum command tree.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SPECtrum? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SPECtrum? query and raise an AssertionError if the returned value does not match value.

Properties

.base: The PLOT:PLOT<x>:SPECtrum:BASE command.
.dynrange: The PLOT:PLOT<x>:SPECtrum:DYNRange command.

base `property` ¶

base: PlotPlotItemSpectrumBase

Return the PLOT:PLOT<x>:SPECtrum:BASE command.

Description

This command sets or queries the spectrum base. Undefined for non-spectrum plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SPECtrum:BASE? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SPECtrum:BASE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:SPECtrum:BASE value command.

SCPI Syntax

- PLOT:PLOT<x>:SPECtrum:BASE <NR1>
- PLOT:PLOT<x>:SPECtrum:BASE?

Info

<NR1> is the spectrum base.

dynrange `property` ¶

dynrange: PlotPlotItemSpectrumDynrange

Return the PLOT:PLOT<x>:SPECtrum:DYNRange command.

Description

This command sets or queries the dynamic range value.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SPECtrum:DYNRange? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SPECtrum:DYNRange? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:SPECtrum:DYNRange value command.

SCPI Syntax

- PLOT:PLOT<x>:SPECtrum:DYNRange <NR3>
- PLOT:PLOT<x>:SPECtrum:DYNRange?

Info

<NR3> is the dynamic range value.

PlotPlotItemSpectrumBase ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:SPECtrum:BASE command.

Description

This command sets or queries the spectrum base. Undefined for non-spectrum plots.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SPECtrum:BASE? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SPECtrum:BASE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:SPECtrum:BASE value command.

SCPI Syntax

- PLOT:PLOT<x>:SPECtrum:BASE <NR1>
- PLOT:PLOT<x>:SPECtrum:BASE?

Info

<NR1> is the spectrum base.

PlotPlotItemSpectrumDynrange ¶

Bases: SCPICmdWrite, SCPICmdRead

The PLOT:PLOT<x>:SPECtrum:DYNRange command.

Description

This command sets or queries the dynamic range value.

Usage

Using the .query() method will send the PLOT:PLOT<x>:SPECtrum:DYNRange? query.
Using the .verify(value) method will send the PLOT:PLOT<x>:SPECtrum:DYNRange? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the PLOT:PLOT<x>:SPECtrum:DYNRange value command.

SCPI Syntax

- PLOT:PLOT<x>:SPECtrum:DYNRange <NR3>
- PLOT:PLOT<x>:SPECtrum:DYNRange?

Info

<NR3> is the dynamic range value.

PlotPlotItemType ¶

Bases: SCPICmdWrite

The PLOT:PLOT<x>:TYPe command.

Description

This command sets or returns the current plot type of the specified plot.

Usage

Using the .write(value) method will send the PLOT:PLOT<x>:TYPe value command.

SCPI Syntax

- PLOT:PLOT<x>:TYPe {NONE|BATHTUB|EYEDIAGRAM|HARMONICS|HISTOGRAM|IMDATIMETREND|IMDAACQTREND|INDUCTANCE|IVSINTEGRALV|MAGPROPERTY|PHASENOISE|PHASOR|SOA|SPECTRUM|SSCPROFILE|SWL|TIEHISTOGRAM|TIETIMETREND|TIESPECTRUM|TIMETREND|XY|XYZ}

Info

<x> is the plot number. This is the equivalent of the number shown on a plot heading in the UI.
NONE does not create a plot.
BATHTUB creates a bathtub plot.
EYEDIAGRAM creates an eye diagram. This plot type is not available on a 4 Series MSO instrument.
HARMONICS creates a harmonics bar graph.
HISTOGRAM creates a histogram plot.
IMDATIMETREND creates a IMDA time trend plot. This plot type requires option IMDA.
IMDAACQTREND creates a IMDA acq trend plot. This plot type requires option IMDA.
INDUCTANCE creates a inductance plot.
IVSINTEGRALV creates a I vs. ∫V plot.
PHASENOISE creates a phase noise plot.
PHASOR creates the Phasor Diagram. This plot type requires option 5-DPM on MSO58/56 series instruments.
MAGPROPERTY creates a BH curve.
SOA creates an SOA plot.
SPECTRUM creates a spectrum plot.
SSCPROFILE creates a SSC profile plot.
SWL creates a Switching Loss plot.
TIEHISTOGRAM creates a TIE histogram plot.
TIESPECTRUM creates a TIE spectrum plot.
TIETIMETREND creates a TIE time trend plot.
TIMETREND creates a time trend plot.
XY creates a XY plot.
XYZ creates a XYZ plot.

plot ¶

Plot ¶

addnew property ¶

delete property ¶

list property ¶

plot property ¶

PlotAddnew ¶

PlotDelete ¶

PlotList ¶

PlotPlotItem ¶

bathtub property ¶

bittype property ¶

exportraw property ¶

extenduis property ¶

eyerender property ¶

imda property ¶

imdaplotdisplay property ¶

label property ¶

mask property ¶

maskoffset property ¶

numbins property ¶

ptype property ¶

railnum property ¶

source1 property ¶

spectrum property ¶

type property ¶

PlotPlotItemBathtub ¶

ber property ¶

xaxisunits property ¶

PlotPlotItemBathtubBer ¶

PlotPlotItemBathtubXaxisunits ¶

PlotPlotItemBittype ¶

PlotPlotItemExportraw ¶

PlotPlotItemExtenduis ¶

PlotPlotItemEyerender ¶

PlotPlotItemImda ¶

meas property ¶

PlotPlotItemImdaMeas ¶

PlotPlotItemImdaplotdisplay ¶

PlotPlotItemLabel ¶

color property ¶

font property ¶

name property ¶

xpos property ¶

ypos property ¶

PlotPlotItemLabelColor ¶

PlotPlotItemLabelFont ¶

bold property ¶

italic property ¶

size property ¶

type property ¶

underline property ¶

PlotPlotItemLabelFontBold ¶

PlotPlotItemLabelFontItalic ¶

PlotPlotItemLabelFontSize ¶

PlotPlotItemLabelFontType ¶

PlotPlotItemLabelFontUnderline ¶

PlotPlotItemLabelName ¶

PlotPlotItemLabelXpos ¶

PlotPlotItemLabelYpos ¶

PlotPlotItemMask ¶

PlotPlotItemMaskoffset ¶

horizontal property ¶

percentui property ¶

PlotPlotItemMaskoffsetHorizontal ¶

autofit property ¶

PlotPlotItemMaskoffsetHorizontalAutofit ¶

PlotPlotItemMaskoffsetPercentui ¶

from_ property ¶

to property ¶

PlotPlotItemMaskoffsetPercentuiFrom ¶

PlotPlotItemMaskoffsetPercentuiTo ¶

PlotPlotItemNumbins ¶

PlotPlotItemPtype ¶

PlotPlotItemRailnum ¶

PlotPlotItemSource1 ¶

PlotPlotItemSpectrum ¶

base property ¶

dynrange property ¶

PlotPlotItemSpectrumBase ¶

addnew `property` ¶

delete `property` ¶

list `property` ¶

plot `property` ¶

bathtub `property` ¶

bittype `property` ¶

exportraw `property` ¶

extenduis `property` ¶

eyerender `property` ¶

imda `property` ¶

imdaplotdisplay `property` ¶

label `property` ¶

mask `property` ¶

maskoffset `property` ¶

numbins `property` ¶

ptype `property` ¶

railnum `property` ¶

source1 `property` ¶

spectrum `property` ¶

type `property` ¶

ber `property` ¶

xaxisunits `property` ¶

meas `property` ¶

color `property` ¶

font `property` ¶

name `property` ¶

xpos `property` ¶

ypos `property` ¶

bold `property` ¶

italic `property` ¶

size `property` ¶

type `property` ¶

underline `property` ¶

horizontal `property` ¶

percentui `property` ¶

autofit `property` ¶

from_ `property` ¶

to `property` ¶

base `property` ¶

dynrange `property` ¶