trigger ¶

The trigger commands module.

These commands are used in the following models: DPO4KB, MDO4K, MSO4K, MSO4KB

THIS FILE IS AUTO-GENERATED, IT SHOULD NOT BE MANUALLY MODIFIED.

Please report an issue if one is found.

Commands and Queries

- TRIGger FORCe
- TRIGger:A SETLevel
- TRIGger:A:BANDWidth:RF:HIGH?
- TRIGger:A:BANDWidth:RF:LOW?
- TRIGger:A:BUS {I2C|SPI|CAN|RS232C|PARallel|USB|LIN|FLEXRay|AUDio|ETHERnet|MIL1553B}
- TRIGger:A:BUS:B<x>:ARINC429A:CONDition {STARt|END|LABel|DATA|LABELANDDATA|ERRor}
- TRIGger:A:BUS:B<x>:ARINC429A:CONDition?
- TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE {ANY|GAP|WORD|PARity}
- TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE?
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue?
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier {LESSthan|MOREthan|Equal|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier?
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue?
- TRIGger:A:BUS:B<x>:ARINC429A:SDI <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:SDI?
- TRIGger:A:BUS:B<x>:ARINC429A:SSM <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:SSM?
- TRIGger:A:BUS:B<x>:AUDio:CONDition {SOF|DATA}
- TRIGger:A:BUS:B<x>:AUDio:CONDition?
- TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue <String>
- TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue?
- TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet?
- TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier?
- TRIGger:A:BUS:B<x>:AUDio:DATa:VALue <String>
- TRIGger:A:BUS:B<x>:AUDio:DATa:VALue?
- TRIGger:A:BUS:B<x>:AUDio:DATa:WORD {EITher|LEFt|RIGht}
- TRIGger:A:BUS:B<x>:AUDio:DATa:WORD?
- TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe {STandard|EXTENDed}
- TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe?
- TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue?
- TRIGger:A:BUS:B<x>:CAN:CONDition {SOF|FRAMEtype|IDentifier|DATA|IDANDDATA|EOF|ACKMISS|ERROR|FORMERRor|ANYERRor|FDBRS|FDESI}
- TRIGger:A:BUS:B<x>:CAN:CONDition?
- TRIGger:A:BUS:B<x>:CAN:DATa:DIRection {READ|WRITE|NOCARE}
- TRIGger:A:BUS:B<x>:CAN:DATa:DIRection?
- TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet?
- TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier {LESSthan|Than|EQual|UNEQual|LESSEQual|EQual}
- TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier?
- TRIGger:A:BUS:B<x>:CAN:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:CAN:DATa:SIZe?
- TRIGger:A:BUS:B<x>:CAN:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:DATa:VALue?
- TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT {ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
- TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT?
- TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT {ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
- TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT?
- TRIGger:A:BUS:B<x>:CAN:FRAMEtype {DATA|REMote|ERRor|OVERLoad}
- TRIGger:A:BUS:B<x>:CAN:FRAMEtype?
- TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe {STandard|EXTENDed}
- TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe?
- TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:CONDition {SFD|MACADDRess|MACLENgth|IPHeader|TCPHeader|DATa|EOP|IDLe|FCSError|QTAG}
- TRIGger:A:BUS:B<x>:ETHERnet:CONDition?
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue?
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet?
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe?
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe {BASic|QTAG}
- TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe?
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue?
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue?
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:ETHERnet:QUALifier?
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue?
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue?
- TRIGger:A:BUS:B<x>:FLEXray:CONDition {SOF|FRAMEType|IDentifier|CYCLEcount|HEADer|DATA|IDANDDATA|EOF|ERROR}
- TRIGger:A:BUS:B<x>:FLEXray:CONDition?
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue?
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier?
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue?
- TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue?
- TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet?
- TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier?
- TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe?
- TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue?
- TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE {STATic|DYNAMic|ANY}
- TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE?
- TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE {CRCHeader|CRCTrailer|SYNCFrame|STARTupnosync|NULLFRStatic|NULLFRDynamic}
- TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE?
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue?
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier?
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue?
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEType {NORMal|PAYLoad|NULL|SYNC|STARTup}
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEType?
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC?
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount?
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID?
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits?
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength?
- TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe {ADDR7|ADDR10}
- TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe?
- TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe {GENeralcall|STARtbyte|HSmode|EEPROM|USER}
- TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe?
- TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue?
- TRIGger:A:BUS:B<x>:I2C:CONDition {STARt|STOP|REPEATstart|ACKMISS|ADDRess|DATA|ADDRANDDATA}
- TRIGger:A:BUS:B<x>:I2C:CONDition?
- TRIGger:A:BUS:B<x>:I2C:DATa:DIRection {READ|WRITE|NOCARE}
- TRIGger:A:BUS:B<x>:I2C:DATa:DIRection?
- TRIGger:A:BUS:B<x>:I2C:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:I2C:DATa:SIZe?
- TRIGger:A:BUS:B<x>:I2C:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:I2C:DATa:VALue?
- TRIGger:A:BUS:B<x>:LIN:CONDition {SYNCField|IDentifier|DATA|IDANDDATA|WAKEup|SLEEP|ERROR}
- TRIGger:A:BUS:B<x>:LIN:CONDition?
- TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue?
- TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier?
- TRIGger:A:BUS:B<x>:LIN:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:LIN:DATa:SIZe?
- TRIGger:A:BUS:B<x>:LIN:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:LIN:DATa:VALue?
- TRIGger:A:BUS:B<x>:LIN:ERRTYPE {SYNC|PARity|CHecksum|HEADertime|RESPtime|FRAMetime}
- TRIGger:A:BUS:B<x>:LIN:ERRTYPE?
- TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue <QString>
- TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue?
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue?
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier?
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue?
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt?
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity?
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress?
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit {RX|TX|X}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit?
- TRIGger:A:BUS:B<x>:MIL1553B:CONDition {SYNC|COMMAND|STATus|DATA|TIMe|ERRor}
- TRIGger:A:BUS:B<x>:MIL1553B:CONDition?
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity?
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue?
- TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE {PARity|SYNC|MANCHester|DATA}
- TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF?
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity?
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit <NR3>
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit?
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit <NR3>
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit?
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier {LESSthan|MOREthan|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier?
- TRIGger:A:BUS:B<x>:PARallel:VALue <QString>
- TRIGger:A:BUS:B<x>:PARallel:VALue?
- TRIGger:A:BUS:B<x>:RS232C:CONDition {RXSTArt|RXDATA|RXENDPacket|TXSTArt|TXDATA|TXENDPacket}
- TRIGger:A:BUS:B<x>:RS232C:CONDition?
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe?
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue?
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe?
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue?
- TRIGger:A:BUS:B<x>:SPI:CONDition {SS|STARTofframe|MISO|MOSI|MISOMOSI}
- TRIGger:A:BUS:B<x>:SPI:CONDition?
- TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue?
- TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue?
- TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue?
- TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue?
- TRIGger:A:BUS:B<x>:SPI:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:SPI:DATa:SIZe?
- TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue?
- TRIGger:A:BUS:B<x>:USB:ADDRess:VALue <Qstring>
- TRIGger:A:BUS:B<x>:USB:ADDRess:VALue?
- TRIGger:A:BUS:B<x>:USB:CONDition {SYNC|RESET|SUSPEND|RESUME|EOP|TOKENPacket|DATAPacket|HANDSHAKEPacket|SPECIALPacket|ERRor}
- TRIGger:A:BUS:B<x>:USB:CONDition?
- TRIGger:A:BUS:B<x>:USB:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:USB:DATa:HIVALue?
- TRIGger:A:BUS:B<x>:USB:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:USB:DATa:OFFSet?
- TRIGger:A:BUS:B<x>:USB:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:USB:DATa:SIZe?
- TRIGger:A:BUS:B<x>:USB:DATa:TYPe {ANY|DATA<x>}
- TRIGger:A:BUS:B<x>:USB:DATa:TYPe?
- TRIGger:A:BUS:B<x>:USB:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:DATa:VALue?
- TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue?
- TRIGger:A:BUS:B<x>:USB:ERRTYPE {PID|CRC5|CRC16|BITSTUFFing}
- TRIGger:A:BUS:B<x>:USB:ERRTYPE?
- TRIGger:A:BUS:B<x>:USB:HANDSHAKEType {ANY|NAK|ACK|STALL}
- TRIGger:A:BUS:B<x>:USB:HANDSHAKEType?
- TRIGger:A:BUS:B<x>:USB:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:USB:QUALifier?
- TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber <QString>
- TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber?
- TRIGger:A:BUS:B<x>:USB:SPECIALType {ANY|PREamble|RESERVed}
- TRIGger:A:BUS:B<x>:USB:SPECIALType?
- TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue {NOCARE|CONTRol|ISOchronous|BULK|INTERRUPT}
- TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue?
- TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue?
- TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue?
- TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue {NOCARE|SSPLIT|CSPLIT}
- TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue?
- TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue {NOCARE|FULLSPeed|LOWSPeed|ISOSTART|ISOMID|ISOEND|ISOALL}
- TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue?
- TRIGger:A:BUS:B<x>:USB:TOKENType {ANY|SOF|OUT|IN|SETUP}
- TRIGger:A:BUS:B<x>:USB:TOKENType?
- TRIGger:A:BUS:SOUrce {B<x>}
- TRIGger:A:BUS:SOUrce?
- TRIGger:A:BUS?
- TRIGger:A:EDGE:COUPling {AC|DC|HFRej|LFRej|NOISErej}
- TRIGger:A:EDGE:COUPling?
- TRIGger:A:EDGE:SLOpe {RISe|FALL|EITHer}
- TRIGger:A:EDGE:SLOpe?
- TRIGger:A:EDGE:SOUrce {AUX|CH<x>|D<x>|LINE|RF}
- TRIGger:A:EDGE:SOUrce?
- TRIGger:A:EDGE?
- TRIGger:A:HOLDoff:TIMe <NR3>
- TRIGger:A:HOLDoff:TIMe?
- TRIGger:A:HOLDoff?
- TRIGger:A:LEVel:AUXin {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:AUXin?
- TRIGger:A:LEVel:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:CH<x>?
- TRIGger:A:LEVel:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:D<x>?
- TRIGger:A:LOGIc:CLAss {LOGIC|SETHold}
- TRIGger:A:LOGIc:CLAss?
- TRIGger:A:LOGIc:FUNCtion {AND|NANd|NOR|OR}
- TRIGger:A:LOGIc:FUNCtion?
- TRIGger:A:LOGIc:INPut:CH<x> {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:CH<x>?
- TRIGger:A:LOGIc:INPut:CLOCk:EDGE {FALL|RISe}
- TRIGger:A:LOGIc:INPut:CLOCk:EDGE?
- TRIGger:A:LOGIc:INPut:CLOCk:SOUrce {CH<x>|D<x>|RF|NONE}
- TRIGger:A:LOGIc:INPut:CLOCk:SOUrce?
- TRIGger:A:LOGIc:INPut:D<x> {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:D<x>?
- TRIGger:A:LOGIc:INPut:RF {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:RF?
- TRIGger:A:LOGIc:INPut?
- TRIGger:A:LOGIc:PATtern:DELTatime <NR3>
- TRIGger:A:LOGIc:PATtern:DELTatime?
- TRIGger:A:LOGIc:PATtern:WHEn {TRUe|FALSe|LESSthan|MOREthan|EQual|UNEQual}
- TRIGger:A:LOGIc:PATtern:WHEn?
- TRIGger:A:LOGIc:PATtern?
- TRIGger:A:LOGIc:THReshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOGIc:THReshold:CH<x>?
- TRIGger:A:LOGIc:THReshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOGIc:THReshold:D<x>?
- TRIGger:A:LOGIc:THReshold:RF {<NR3>}
- TRIGger:A:LOGIc:THReshold:RF?
- TRIGger:A:LOGIc?
- TRIGger:A:LOWerthreshold:AUX {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:AUX?
- TRIGger:A:LOWerthreshold:CH<x> {ECL|TTL|<NR3>}
- TRIGger:A:LOWerthreshold:CH<x>?
- TRIGger:A:LOWerthreshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:D<x>?
- TRIGger:A:LOWerthreshold:EXT {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:EXT?
- TRIGger:A:LOWerthreshold:RF {<NR3>}
- TRIGger:A:LOWerthreshold:RF?
- TRIGger:A:MODe {AUTO|NORMal}
- TRIGger:A:MODe?
- TRIGger:A:PULSEWidth:HIGHLimit <NR3>
- TRIGger:A:PULSEWidth:HIGHLimit?
- TRIGger:A:PULSEWidth:LOWLimit <NR3>
- TRIGger:A:PULSEWidth:LOWLimit?
- TRIGger:A:PULSEWidth:POLarity {NEGative|POSitive}
- TRIGger:A:PULSEWidth:POLarity?
- TRIGger:A:PULSEWidth:SOUrce {CH<x>|LINE|AUX|D<x>|RF}
- TRIGger:A:PULSEWidth:SOUrce?
- TRIGger:A:PULSEWidth:WHEn {LESSthan|MOREthan|EQual|UNEQual|WIThin|OUTside}
- TRIGger:A:PULSEWidth:WHEn?
- TRIGger:A:PULSEWidth:WIDth <NR3>
- TRIGger:A:PULSEWidth:WIDth?
- TRIGger:A:PULse:CLAss {RUNt|WIDth|TRANsition|TIMEOut}
- TRIGger:A:PULse:CLAss?
- TRIGger:A:RISEFall:DELTatime <NR3>
- TRIGger:A:RISEFall:DELTatime?
- TRIGger:A:RISEFall:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:RISEFall:POLarity?
- TRIGger:A:RISEFall:SOUrce {CH<x>}
- TRIGger:A:RISEFall:SOUrce?
- TRIGger:A:RISEFall:WHEn {SLOWer|FASTer|EQual|UNEQual}
- TRIGger:A:RISEFall:WHEn?
- TRIGger:A:RISEFall?
- TRIGger:A:RUNT:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:RUNT:POLarity?
- TRIGger:A:RUNT:SOUrce {CH<x>|RF}
- TRIGger:A:RUNT:SOUrce?
- TRIGger:A:RUNT:WHEn {LESSthan|MOREthan|EQual|UNEQual|OCCURS}
- TRIGger:A:RUNT:WHEn?
- TRIGger:A:RUNT:WIDth <NR3>
- TRIGger:A:RUNT:WIDth?
- TRIGger:A:RUNT?
- TRIGger:A:SETHold:CLOCk:EDGE {FALL|RISe}
- TRIGger:A:SETHold:CLOCk:EDGE?
- TRIGger:A:SETHold:CLOCk:SOUrce {CH<x>|D<x>|AUX}
- TRIGger:A:SETHold:CLOCk:SOUrce?
- TRIGger:A:SETHold:CLOCk:THReshold {<NR3>|TTL}
- TRIGger:A:SETHold:CLOCk:THReshold?
- TRIGger:A:SETHold:CLOCk?
- TRIGger:A:SETHold:DATa:SOUrce {CH<x>|D<x>|AUX}
- TRIGger:A:SETHold:DATa:SOUrce?
- TRIGger:A:SETHold:DATa:THReshold {<NR3>|TTL}
- TRIGger:A:SETHold:DATa:THReshold?
- TRIGger:A:SETHold:DATa?
- TRIGger:A:SETHold:HOLDTime <NR3>
- TRIGger:A:SETHold:HOLDTime?
- TRIGger:A:SETHold:SETTime <NR3>
- TRIGger:A:SETHold:SETTime?
- TRIGger:A:SETHold:THReshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:SETHold:THReshold:CH<x>?
- TRIGger:A:SETHold:THReshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:SETHold:THReshold:D<x>?
- TRIGger:A:SETHold?
- TRIGger:A:TIMEOut:POLarity {STAYSHigh|STAYSLow|EITher}
- TRIGger:A:TIMEOut:POLarity?
- TRIGger:A:TIMEOut:SOUrce {CH<x>|LINE|AUX|D<x>|RF}
- TRIGger:A:TIMEOut:SOUrce?
- TRIGger:A:TIMEOut:TIMe <NR3>
- TRIGger:A:TIMEOut:TIMe?
- TRIGger:A:TRANsition:DELTatime <NR3>
- TRIGger:A:TRANsition:DELTatime?
- TRIGger:A:TRANsition:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:TRANsition:POLarity?
- TRIGger:A:TRANsition:SOUrce {CH<x>}
- TRIGger:A:TRANsition:SOUrce?
- TRIGger:A:TRANsition:WHEn {SLOWer|FASTer|EQual|UNEQual}
- TRIGger:A:TRANsition:WHEn?
- TRIGger:A:TRANsition?
- TRIGger:A:TYPe {EDGe|LOGIc|PULSe|BUS|VIDeo}
- TRIGger:A:TYPe?
- TRIGger:A:UPPerthreshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:UPPerthreshold:CH<x>?
- TRIGger:A:UPPerthreshold:RF {<NR3>}
- TRIGger:A:UPPerthreshold:RF?
- TRIGger:A:VIDeo:CUSTom:FORMat {INTERLAced|PROGressive}
- TRIGger:A:VIDeo:CUSTom:FORMat?
- TRIGger:A:VIDeo:CUSTom:LINEPeriod <NR3>
- TRIGger:A:VIDeo:CUSTom:LINEPeriod?
- TRIGger:A:VIDeo:CUSTom:SYNCInterval <NR3>
- TRIGger:A:VIDeo:CUSTom:SYNCInterval?
- TRIGger:A:VIDeo:CUSTom:TYPe {INTERLAced|PROGressive}
- TRIGger:A:VIDeo:CUSTom:TYPe?
- TRIGger:A:VIDeo:FIELD {ODD|EVEN|ALLFields|ALLLines|NUMERic}
- TRIGger:A:VIDeo:FIELD?
- TRIGger:A:VIDeo:HOLDoff:FIELD <NR3>
- TRIGger:A:VIDeo:HOLDoff:FIELD?
- TRIGger:A:VIDeo:LINE <NR1>
- TRIGger:A:VIDeo:LINE?
- TRIGger:A:VIDeo:POLarity {NEGative|POSitive}
- TRIGger:A:VIDeo:POLarity?
- TRIGger:A:VIDeo:SOUrce {CH<x>}
- TRIGger:A:VIDeo:SOUrce?
- TRIGger:A:VIDeo:STANdard {NTSc|PAL|SECAM|BILevelcustom|TRILevelcustom|HD480P60|HD576P50|HD720P30|HD720P50|HD720P60|HD875I60|HD1080P24|HD1080SF24|HD1080I50|HD1080I60|HD1080P25|HD1080P30|HD1080P50|HD1080P60}
- TRIGger:A:VIDeo:STANdard?
- TRIGger:A:VIDeo:SYNC {ODD|EVEN|ALLFields|ALLLines|NUMERic}
- TRIGger:A:VIDeo:SYNC?
- TRIGger:A:VIDeo?
- TRIGger:A?
- TRIGger:B SETLevel
- TRIGger:B:BY {EVENTS|TIMe}
- TRIGger:B:BY?
- TRIGger:B:EDGE:COUPling {DC|HFRej|LFRej|NOISErej}
- TRIGger:B:EDGE:COUPling?
- TRIGger:B:EDGE:SLOpe {RISe|FALL}
- TRIGger:B:EDGE:SLOpe?
- TRIGger:B:EDGE:SOUrce {CH<x>|AUX|LINE|RF}
- TRIGger:B:EDGE:SOUrce?
- TRIGger:B:EDGE?
- TRIGger:B:EVENTS:COUNt <NR1>
- TRIGger:B:EVENTS:COUNt?
- TRIGger:B:EVENTS?
- TRIGger:B:LEVel {TTL|<NR3>}
- TRIGger:B:LEVel:CH<x> {ECL|TTL|<NR3>}
- TRIGger:B:LEVel:CH<x>?
- TRIGger:B:LEVel:D<x> {ECL|TTL|<NR3>}
- TRIGger:B:LEVel:D<x>?
- TRIGger:B:LEVel?
- TRIGger:B:LOWerthreshold:CH<x> {ECL|TTL|<NR3>}
- TRIGger:B:LOWerthreshold:CH<x>?
- TRIGger:B:LOWerthreshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:B:LOWerthreshold:D<x>?
- TRIGger:B:STATE {ON|OFF|<NR1>}
- TRIGger:B:STATE?
- TRIGger:B:TIMe <NR3>
- TRIGger:B:TIMe?
- TRIGger:B:TYPe EDGE
- TRIGger:B:TYPe?
- TRIGger:B?
- TRIGger:EXTernal:PRObe <NR3>
- TRIGger:EXTernal:PRObe?
- TRIGger:EXTernal:YUNIts?
- TRIGger:EXTernal?
- TRIGger:FREQuency?
- TRIGger:STATE?
- TRIGger?

Trigger ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger command.

Description

This command forces a trigger event to occur. The query returns the current trigger parameters for the instrument.

Usage

Using the .query() method will send the TRIGger? query.
Using the .verify(value) method will send the TRIGger? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger value command.

SCPI Syntax

- TRIGger FORCe
- TRIGger?

Info

FORCe creates a trigger event. If TRIGger:STATE is set to READy, the acquisition will complete. Otherwise, this command will be ignored. This is equivalent to pressing the Force button on the front panel.

Properties

.a: The TRIGger:A command.
.b: The TRIGger:B command.
.external: The TRIGger:EXTernal command.
.frequency: The TRIGger:FREQuency command.
.state: The TRIGger:STATE command.

a `property` ¶

a: TriggerA

Return the TRIGger:A command.

Description

This command sets the A trigger level automatically to 50% of the range of the minimum and maximum values of the trigger input signal. The query returns current trigger parameters. The trigger level is the voltage threshold through which the trigger source signal must pass to generate a trigger event. This command is equivalent to pushing the LEVEL knob on the front panel.

Usage

Using the .query() method will send the TRIGger:A? query.
Using the .verify(value) method will send the TRIGger:A? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A value command.

SCPI Syntax

- TRIGger:A SETLevel
- TRIGger:A?

Info

SETLevel sets the trigger level to 50% of the range of the minimum and maximum values of the trigger input signal.

Sub-properties

.bandwidth: The TRIGger:A:BANDWidth command tree.
.bus: The TRIGger:A:BUS command.
.edge: The TRIGger:A:EDGE command.
.holdoff: The TRIGger:A:HOLDoff command.
.level: The TRIGger:A:LEVel command tree.
.logic: The TRIGger:A:LOGIc command.
.lowerthreshold: The TRIGger:A:LOWerthreshold command tree.
.mode: The TRIGger:A:MODe command.
.pulsewidth: The TRIGger:A:PULSEWidth command tree.
.pulse: The TRIGger:A:PULse command tree.
.runt: The TRIGger:A:RUNT command.
.sethold: The TRIGger:A:SETHold command.
.timeout: The TRIGger:A:TIMEOut command tree.
.type: The TRIGger:A:TYPe command.
.upperthreshold: The TRIGger:A:UPPerthreshold command tree.
.video: The TRIGger:A:VIDeo command.
.transition: The TRIGger:A:TRANsition command.
.risefall: The TRIGger:A:RISEFall command.

b `property` ¶

b: TriggerB

Return the TRIGger:B command.

Description

Sets the B trigger level to 50% of minimum and maximum. The query form of this command returns the B trigger parameters. This command is similar to selecting B Event (Delayed) Trigger Setup from the Trigger menu and then viewing the current setups.

Usage

Using the .query() method will send the TRIGger:B? query.
Using the .verify(value) method will send the TRIGger:B? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B value command.

SCPI Syntax

- TRIGger:B SETLevel
- TRIGger:B?

Info

SETLevel sets the B trigger level to 50% of MIN and MAX.

Sub-properties

.by: The TRIGger:B:BY command.
.edge: The TRIGger:B:EDGE command.
.events: The TRIGger:B:EVENTS command.
.level: The TRIGger:B:LEVel command.
.lowerthreshold: The TRIGger:B:LOWerthreshold command tree.
.state: The TRIGger:B:STATE command.
.time: The TRIGger:B:TIMe command.
.type: The TRIGger:B:TYPe command.

external `property` ¶

external: TriggerExternal

Return the TRIGger:EXTernal command.

Description

Returns all external trigger-related parameters for the probe attached to the Aux Input connector.

Usage

Using the .query() method will send the TRIGger:EXTernal? query.
Using the .verify(value) method will send the TRIGger:EXTernal? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:EXTernal?

Sub-properties

.probe: The TRIGger:EXTernal:PRObe command.
.yunits: The TRIGger:EXTernal:YUNIts command.

frequency `property` ¶

frequency: TriggerFrequency

Return the TRIGger:FREQuency command.

Description

Returns the trigger frequency in hertz if available. If the trigger frequency is not currently available, the IEEE Not A Number (NaN = 99.10E+36) value is returned. The maximum precision of the returned frequency is 12 digits. Use the DISPLAY:TRIGFREQUENCY command to enable/disable the calculation of the trigger frequency.

Usage

Using the .query() method will send the TRIGger:FREQuency? query.
Using the .verify(value) method will send the TRIGger:FREQuency? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:FREQuency?

state `property` ¶

state: TriggerState

Return the TRIGger:STATE command.

Description

This query-only command returns the current state of the triggering system.

Usage

Using the .query() method will send the TRIGger:STATE? query.
Using the .verify(value) method will send the TRIGger:STATE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:STATE?

TriggerA ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A command.

Description

This command sets the A trigger level automatically to 50% of the range of the minimum and maximum values of the trigger input signal. The query returns current trigger parameters. The trigger level is the voltage threshold through which the trigger source signal must pass to generate a trigger event. This command is equivalent to pushing the LEVEL knob on the front panel.

Usage

Using the .query() method will send the TRIGger:A? query.
Using the .verify(value) method will send the TRIGger:A? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A value command.

SCPI Syntax

- TRIGger:A SETLevel
- TRIGger:A?

Info

SETLevel sets the trigger level to 50% of the range of the minimum and maximum values of the trigger input signal.

Properties

.bandwidth: The TRIGger:A:BANDWidth command tree.
.bus: The TRIGger:A:BUS command.
.edge: The TRIGger:A:EDGE command.
.holdoff: The TRIGger:A:HOLDoff command.
.level: The TRIGger:A:LEVel command tree.
.logic: The TRIGger:A:LOGIc command.
.lowerthreshold: The TRIGger:A:LOWerthreshold command tree.
.mode: The TRIGger:A:MODe command.
.pulsewidth: The TRIGger:A:PULSEWidth command tree.
.pulse: The TRIGger:A:PULse command tree.
.runt: The TRIGger:A:RUNT command.
.sethold: The TRIGger:A:SETHold command.
.timeout: The TRIGger:A:TIMEOut command tree.
.type: The TRIGger:A:TYPe command.
.upperthreshold: The TRIGger:A:UPPerthreshold command tree.
.video: The TRIGger:A:VIDeo command.
.transition: The TRIGger:A:TRANsition command.
.risefall: The TRIGger:A:RISEFall command.

bandwidth `property` ¶

bandwidth: TriggerABandwidth

Return the TRIGger:A:BANDWidth command tree.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.rf: The TRIGger:A:BANDWidth:RF command tree.

bus `property` ¶

bus: TriggerABus

Return the TRIGger:A:BUS command.

Description

This command specifies the bus type to trigger on. It supports CAN, I 2 C, SPI, RS-232, Ethernet, MIL-STD-1553, LIN, USB, audio, FlexRay buses (with the appropriate application module installed) as well as parallel signals (with option 3-MSO only.). There are two buses, B1-B2. Each bus can be independently set to one of the serial trigger types.

Usage

Using the .query() method will send the TRIGger:A:BUS? query.
Using the .verify(value) method will send the TRIGger:A:BUS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS value command.

SCPI Syntax

- TRIGger:A:BUS {I2C|SPI|CAN|RS232C|PARallel|USB|LIN|FLEXRay|AUDio|ETHERnet|MIL1553B}
- TRIGger:A:BUS?

Info

I2C specifies the Inter-IC bus.
SPI specifies the Serial Peripheral Interface bus (not available on two-channel models).
CAN specifies the Controller Area Network bus.
RS232C specifies the RS-232C bus.
PARallel specifies the Parallel bus.
USB specifies the USB bus.
LIN specifies the LIN bus.
FLEXRay specifies the FLexRay bus.
AUDio specifies the audio bus.
ETHERnet specifies the Ethernet bus.
MIL1553B specifies the MIL-STD-1553 bus.

Sub-properties

.b: The TRIGger:A:BUS:B<x> command tree.
.source: The TRIGger:A:BUS:SOUrce command.

edge `property` ¶

edge: TriggerAEdge

Return the TRIGger:A:EDGE command.

Description

Returns the trigger source, coupling, and slope for the A edge trigger.

Usage

Using the .query() method will send the TRIGger:A:EDGE? query.
Using the .verify(value) method will send the TRIGger:A:EDGE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:EDGE?

Sub-properties

.coupling: The TRIGger:A:EDGE:COUPling command.
.slope: The TRIGger:A:EDGE:SLOpe command.
.source: The TRIGger:A:EDGE:SOUrce command.

holdoff `property` ¶

holdoff: TriggerAHoldoff

Return the TRIGger:A:HOLDoff command.

Description

Returns the A trigger holdoff parameters. These parameters specify the time period during which the trigger circuitry is not looking to generate a trigger event.

Usage

Using the .query() method will send the TRIGger:A:HOLDoff? query.
Using the .verify(value) method will send the TRIGger:A:HOLDoff? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:HOLDoff?

Sub-properties

.time: The TRIGger:A:HOLDoff:TIMe command.

level `property` ¶

level: TriggerALevel

Return the TRIGger:A:LEVel command tree.

Usage

Using the .query() method will send the TRIGger:A:LEVel? query.
Using the .verify(value) method will send the TRIGger:A:LEVel? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.auxin: The TRIGger:A:LEVel:AUXin command.
.ch: The TRIGger:A:LEVel:CH<x> command.
.d: The TRIGger:A:LEVel:D<x> command.

logic `property` ¶

logic: TriggerALogic

Return the TRIGger:A:LOGIc command.

Description

Returns all of the A logic trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:LOGIc? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:LOGIc?

Sub-properties

.class: The TRIGger:A:LOGIc:CLAss command.
.function: The TRIGger:A:LOGIc:FUNCtion command.
.input: The TRIGger:A:LOGIc:INPut command.
.pattern: The TRIGger:A:LOGIc:PATtern command.
.threshold: The TRIGger:A:LOGIc:THReshold command tree.

lowerthreshold `property` ¶

lowerthreshold: TriggerALowerthreshold

Return the TRIGger:A:LOWerthreshold command tree.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.ch: The TRIGger:A:LOWerthreshold:CH<x> command.
.d: The TRIGger:A:LOWerthreshold:D<x> command.
.rf: The TRIGger:A:LOWerthreshold:RF command.
.aux: The TRIGger:A:LOWerthreshold:AUX command.
.ext: The TRIGger:A:LOWerthreshold:EXT command.

mode `property` ¶

mode: TriggerAMode

Return the TRIGger:A:MODe command.

Description

This command sets or queries the A trigger mode. This command is equivalent to pushing the Mode button on the front panel.

Usage

Using the .query() method will send the TRIGger:A:MODe? query.
Using the .verify(value) method will send the TRIGger:A:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:MODe value command.

SCPI Syntax

- TRIGger:A:MODe {AUTO|NORMal}
- TRIGger:A:MODe?

Info

AUTO generates a trigger if one is not detected within a specified time period.
NORMal waits for a valid trigger event.

pulse `property` ¶

pulse: TriggerAPulse

Return the TRIGger:A:PULse command tree.

Usage

Using the .query() method will send the TRIGger:A:PULse? query.
Using the .verify(value) method will send the TRIGger:A:PULse? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.class: The TRIGger:A:PULse:CLAss command.

pulsewidth `property` ¶

pulsewidth: TriggerAPulsewidth

Return the TRIGger:A:PULSEWidth command tree.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.highlimit: The TRIGger:A:PULSEWidth:HIGHLimit command.
.lowlimit: The TRIGger:A:PULSEWidth:LOWLimit command.
.polarity: The TRIGger:A:PULSEWidth:POLarity command.
.source: The TRIGger:A:PULSEWidth:SOUrce command.
.when: The TRIGger:A:PULSEWidth:WHEn command.
.width: The TRIGger:A:PULSEWidth:WIDth command.

risefall `property` ¶

risefall: TriggerARisefall

Return the TRIGger:A:RISEFall command.

Description

Returns transition time trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:RISEFall? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:RISEFall?

Sub-properties

.deltatime: The TRIGger:A:RISEFall:DELTatime command.
.polarity: The TRIGger:A:RISEFall:POLarity command.
.source: The TRIGger:A:RISEFall:SOUrce command.
.when: The TRIGger:A:RISEFall:WHEn command.

runt `property` ¶

runt: TriggerARunt

Return the TRIGger:A:RUNT command.

Description

Returns the current A runt trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:RUNT? query.
Using the .verify(value) method will send the TRIGger:A:RUNT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:RUNT?

Sub-properties

.polarity: The TRIGger:A:RUNT:POLarity command.
.source: The TRIGger:A:RUNT:SOUrce command.
.when: The TRIGger:A:RUNT:WHEn command.
.width: The TRIGger:A:RUNT:WIDth command.

sethold `property` ¶

sethold: TriggerASethold

Return the TRIGger:A:SETHold command.

Description

Returns the clock edge polarity, voltage threshold and source input; data voltage threshold and source; and both setup and hold times for setup and hold violation triggering.

Usage

Using the .query() method will send the TRIGger:A:SETHold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:SETHold?

Sub-properties

.clock: The TRIGger:A:SETHold:CLOCk command.
.data: The TRIGger:A:SETHold:DATa command.
.holdtime: The TRIGger:A:SETHold:HOLDTime command.
.settime: The TRIGger:A:SETHold:SETTime command.
.threshold: The TRIGger:A:SETHold:THReshold command tree.

timeout `property` ¶

timeout: TriggerATimeout

Return the TRIGger:A:TIMEOut command tree.

Usage

Using the .query() method will send the TRIGger:A:TIMEOut? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.polarity: The TRIGger:A:TIMEOut:POLarity command.
.source: The TRIGger:A:TIMEOut:SOUrce command.
.time: The TRIGger:A:TIMEOut:TIMe command.

transition `property` ¶

transition: TriggerATransition

Return the TRIGger:A:TRANsition command.

Description

Returns transition time trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:TRANsition? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:TRANsition?

Sub-properties

.deltatime: The TRIGger:A:TRANsition:DELTatime command.
.polarity: The TRIGger:A:TRANsition:POLarity command.
.source: The TRIGger:A:TRANsition:SOUrce command.
.when: The TRIGger:A:TRANsition:WHEn command.

type `property` ¶

type: TriggerAType

Return the TRIGger:A:TYPe command.

Description

This command sets the type of A trigger (either edge, logic, pulse, bus or video). If you set the trigger type to LOGIc, you also need to set the logic trigger class (logic or setup/hold) using the command TRIGGER:A:LOGIC:CLASS. If you set the trigger type to PULSe, you also need to set the pulse trigger class (either runt, width, transition or timeout), using the command TRIGGER:A:PULSE:CLASS. If you set the trigger type to BUS, you also need to set the bus type (CAN, I 2 C, SPI, RS-232, Ethernet, MIL-STD-1553, LIN, USB, audio, FlexRay, or parallel) using the command TRIGGER:A:BUS.

Usage

Using the .query() method will send the TRIGger:A:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TYPe value command.

SCPI Syntax

- TRIGger:A:TYPe {EDGe|LOGIc|PULSe|BUS|VIDeo}
- TRIGger:A:TYPe?

Info

EDGe is the default trigger. A trigger event occurs when a signal passes through a specified voltage level in a specified direction and is controlled by the TRIGGER:A:EDGE commands.
LOGIc specifies that a trigger occurs when specified conditions are met and is controlled by the TRIGGER:A:LOGIC commands. This trigger type is equivalent to the logic and setup/hold triggers found in the user interface. Use TRIGGER:A:LOGIC:CLASS to further select the logic trigger class (either LOGIC or SETHOLD).
PULSe specifies that a trigger occurs when a specified pulse is found. Use TRIGGER:A:PULSE:CLASS to further select the pulse trigger class (either runt, width, transition or timeout).
BUS specifies that a trigger occurs when a bus signal is found. Supports CAN, I2C, SPI, RS-232, Ethernet, MIL-STD-1553, LIN, USB, audio, FlexRay buses (with the appropriate application module installed) as well as parallel buses. Requires the installation of option 3-MSO. Use TRIGGER:A:BUS to set the bus type.
VIDeo specifies that the trigger occurs when a video signal is found.

upperthreshold `property` ¶

upperthreshold: TriggerAUpperthreshold

Return the TRIGger:A:UPPerthreshold command tree.

Usage

Using the .query() method will send the TRIGger:A:UPPerthreshold? query.
Using the .verify(value) method will send the TRIGger:A:UPPerthreshold? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.ch: The TRIGger:A:UPPerthreshold:CH<x> command.
.rf: The TRIGger:A:UPPerthreshold:RF command.

video `property` ¶

video: TriggerAVideo

Return the TRIGger:A:VIDeo command.

Description

Returns the A trigger video parameters.

Usage

Using the .query() method will send the TRIGger:A:VIDeo? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:VIDeo?

Sub-properties

.custom: The TRIGger:A:VIDeo:CUSTom command tree.
.holdoff: The TRIGger:A:VIDeo:HOLDoff command tree.
.line: The TRIGger:A:VIDeo:LINE command.
.polarity: The TRIGger:A:VIDeo:POLarity command.
.source: The TRIGger:A:VIDeo:SOUrce command.
.standard: The TRIGger:A:VIDeo:STANdard command.
.sync: The TRIGger:A:VIDeo:SYNC command.
.field: The TRIGger:A:VIDeo:FIELD command.

TriggerABandwidth ¶

Bases: SCPICmdRead

The TRIGger:A:BANDWidth command tree.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth? query and raise an AssertionError if the returned value does not match value.

Properties

.rf: The TRIGger:A:BANDWidth:RF command tree.

rf `property` ¶

rf: TriggerABandwidthRf

Return the TRIGger:A:BANDWidth:RF command tree.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth:RF? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth:RF? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.high: The TRIGger:A:BANDWidth:RF:HIGH command.
.low: The TRIGger:A:BANDWidth:RF:LOW command.

TriggerABandwidthRf ¶

Bases: SCPICmdRead

The TRIGger:A:BANDWidth:RF command tree.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth:RF? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth:RF? query and raise an AssertionError if the returned value does not match value.

Properties

.high: The TRIGger:A:BANDWidth:RF:HIGH command.
.low: The TRIGger:A:BANDWidth:RF:LOW command.

high `property` ¶

high: TriggerABandwidthRfHigh

Return the TRIGger:A:BANDWidth:RF:HIGH command.

Description

Returns the high end of the power level trigger bandwidth range as an NR3 value in hertz. This is the value that is displayed in the user interface when the trigger source is RF. This command requires the MDO4TRIG advanced trigger feature to be enabled.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth:RF:HIGH? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth:RF:HIGH? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:BANDWidth:RF:HIGH?

low `property` ¶

low: TriggerABandwidthRfLow

Return the TRIGger:A:BANDWidth:RF:LOW command.

Description

Returns the low end of the power level trigger bandwidth range as an NR3 value in hertz. This is the value that is displayed in the user interface when the trigger source is RF. This command requires the MDO4TRIG advanced trigger feature to be enabled.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth:RF:LOW? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth:RF:LOW? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:BANDWidth:RF:LOW?

TriggerABandwidthRfHigh ¶

Bases: SCPICmdRead

The TRIGger:A:BANDWidth:RF:HIGH command.

Description

Returns the high end of the power level trigger bandwidth range as an NR3 value in hertz. This is the value that is displayed in the user interface when the trigger source is RF. This command requires the MDO4TRIG advanced trigger feature to be enabled.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth:RF:HIGH? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth:RF:HIGH? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:BANDWidth:RF:HIGH?

TriggerABandwidthRfLow ¶

Bases: SCPICmdRead

The TRIGger:A:BANDWidth:RF:LOW command.

Description

Returns the low end of the power level trigger bandwidth range as an NR3 value in hertz. This is the value that is displayed in the user interface when the trigger source is RF. This command requires the MDO4TRIG advanced trigger feature to be enabled.

Usage

Using the .query() method will send the TRIGger:A:BANDWidth:RF:LOW? query.
Using the .verify(value) method will send the TRIGger:A:BANDWidth:RF:LOW? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:BANDWidth:RF:LOW?

TriggerABus ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS command.

Description

This command specifies the bus type to trigger on. It supports CAN, I 2 C, SPI, RS-232, Ethernet, MIL-STD-1553, LIN, USB, audio, FlexRay buses (with the appropriate application module installed) as well as parallel signals (with option 3-MSO only.). There are two buses, B1-B2. Each bus can be independently set to one of the serial trigger types.

Usage

Using the .query() method will send the TRIGger:A:BUS? query.
Using the .verify(value) method will send the TRIGger:A:BUS? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS value command.

SCPI Syntax

- TRIGger:A:BUS {I2C|SPI|CAN|RS232C|PARallel|USB|LIN|FLEXRay|AUDio|ETHERnet|MIL1553B}
- TRIGger:A:BUS?

Info

I2C specifies the Inter-IC bus.
SPI specifies the Serial Peripheral Interface bus (not available on two-channel models).
CAN specifies the Controller Area Network bus.
RS232C specifies the RS-232C bus.
PARallel specifies the Parallel bus.
USB specifies the USB bus.
LIN specifies the LIN bus.
FLEXRay specifies the FLexRay bus.
AUDio specifies the audio bus.
ETHERnet specifies the Ethernet bus.
MIL1553B specifies the MIL-STD-1553 bus.

Properties

.b: The TRIGger:A:BUS:B<x> command tree.
.source: The TRIGger:A:BUS:SOUrce command.

b `property` ¶

b: dict[int, TriggerABusBItem]

Return the TRIGger:A:BUS:B<x> command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.arinc429a: The TRIGger:A:BUS:B<x>:ARINC429A command tree.
.audio: The TRIGger:A:BUS:B<x>:AUDio command tree.
.can: The TRIGger:A:BUS:B<x>:CAN command tree.
.ethernet: The TRIGger:A:BUS:B<x>:ETHERnet command tree.
.flexray: The TRIGger:A:BUS:B<x>:FLEXray command tree.
.i2c: The TRIGger:A:BUS:B<x>:I2C command tree.
.lin: The TRIGger:A:BUS:B<x>:LIN command tree.
.mil1553b: The TRIGger:A:BUS:B<x>:MIL1553B command tree.
.parallel: The TRIGger:A:BUS:B<x>:PARallel command tree.
.rs232c: The TRIGger:A:BUS:B<x>:RS232C command tree.
.spi: The TRIGger:A:BUS:B<x>:SPI command tree.
.usb: The TRIGger:A:BUS:B<x>:USB command tree.

source `property` ¶

source: TriggerABusSource

Return the TRIGger:A:BUS:SOUrce command.

Description

This command specifies the source for a serial or parallel bus trigger, with the appropriate application module installed.

Usage

Using the .query() method will send the TRIGger:A:BUS:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:BUS:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:SOUrce value command.

SCPI Syntax

- TRIGger:A:BUS:SOUrce {B<x>}
- TRIGger:A:BUS:SOUrce?

Info

B1 specifies the Bus 1 source.
B2 specifies the Bus 2 source.
B3 specifies the Bus 3 source.
B4 specifies the Bus 4 source.

TriggerABusBItem ¶

Bases: ValidatedDynamicNumberCmd, SCPICmdRead

The TRIGger:A:BUS:B<x> command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>? query and raise an AssertionError if the returned value does not match value.

Properties

.arinc429a: The TRIGger:A:BUS:B<x>:ARINC429A command tree.
.audio: The TRIGger:A:BUS:B<x>:AUDio command tree.
.can: The TRIGger:A:BUS:B<x>:CAN command tree.
.ethernet: The TRIGger:A:BUS:B<x>:ETHERnet command tree.
.flexray: The TRIGger:A:BUS:B<x>:FLEXray command tree.
.i2c: The TRIGger:A:BUS:B<x>:I2C command tree.
.lin: The TRIGger:A:BUS:B<x>:LIN command tree.
.mil1553b: The TRIGger:A:BUS:B<x>:MIL1553B command tree.
.parallel: The TRIGger:A:BUS:B<x>:PARallel command tree.
.rs232c: The TRIGger:A:BUS:B<x>:RS232C command tree.
.spi: The TRIGger:A:BUS:B<x>:SPI command tree.
.usb: The TRIGger:A:BUS:B<x>:USB command tree.

arinc429a `property` ¶

arinc429a: TriggerABusBItemArinc429a

Return the TRIGger:A:BUS:B<x>:ARINC429A command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:ARINC429A:CONDition command.
.errtype: The TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE command.
.label: The TRIGger:A:BUS:B<x>:ARINC429A:LABel command tree.
.sdi: The TRIGger:A:BUS:B<x>:ARINC429A:SDI command.
.ssm: The TRIGger:A:BUS:B<x>:ARINC429A:SSM command.

audio `property` ¶

audio: TriggerABusBItemAudio

Return the TRIGger:A:BUS:B<x>:AUDio command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:AUDio:CONDition command.
.data: The TRIGger:A:BUS:B<x>:AUDio:DATa command tree.

can `property` ¶

can: TriggerABusBItemCan

Return the TRIGger:A:BUS:B<x>:CAN command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:CAN:CONDition command.
.data: The TRIGger:A:BUS:B<x>:CAN:DATa command tree.
.fd: The TRIGger:A:BUS:B<x>:CAN:FD command tree.
.frametype: The TRIGger:A:BUS:B<x>:CAN:FRAMEtype command.
.identifier: The TRIGger:A:BUS:B<x>:CAN:IDentifier command tree.
.address: The TRIGger:A:BUS:B<x>:CAN:ADDRess command tree.

ethernet `property` ¶

ethernet: TriggerABusBItemEthernet

Return the TRIGger:A:BUS:B<x>:ETHERnet command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:ETHERnet:CONDition command.
.data: The TRIGger:A:BUS:B<x>:ETHERnet:DATa command tree.
.frametype: The TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe command.
.ipheader: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader command tree.
.mac: The TRIGger:A:BUS:B<x>:ETHERnet:MAC command tree.
.qtag: The TRIGger:A:BUS:B<x>:ETHERnet:QTAG command tree.
.qualifier: The TRIGger:A:BUS:B<x>:ETHERnet:QUALifier command.
.tcpheader: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader command tree.

flexray `property` ¶

flexray: TriggerABusBItemFlexray

Return the TRIGger:A:BUS:B<x>:FLEXray command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:FLEXray:CONDition command.
.cyclecount: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount command tree.
.data: The TRIGger:A:BUS:B<x>:FLEXray:DATa command tree.
.eoftype: The TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE command.
.errtype: The TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE command.
.frameid: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID command tree.
.frametype: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEType command.
.header: The TRIGger:A:BUS:B<x>:FLEXray:HEADER command tree.

i2c `property` ¶

i2c: TriggerABusBItemI2c

Return the TRIGger:A:BUS:B<x>:I2C command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.address: The TRIGger:A:BUS:B<x>:I2C:ADDRess command tree.
.condition: The TRIGger:A:BUS:B<x>:I2C:CONDition command.
.data: The TRIGger:A:BUS:B<x>:I2C:DATa command tree.

lin `property` ¶

lin: TriggerABusBItemLin

Return the TRIGger:A:BUS:B<x>:LIN command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:LIN:CONDition command.
.data: The TRIGger:A:BUS:B<x>:LIN:DATa command tree.
.errtype: The TRIGger:A:BUS:B<x>:LIN:ERRTYPE command.
.identifier: The TRIGger:A:BUS:B<x>:LIN:IDentifier command tree.

mil1553b `property` ¶

mil1553b: TriggerABusBItemMil1553b

Return the TRIGger:A:BUS:B<x>:MIL1553B command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.command: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND command tree.
.condition: The TRIGger:A:BUS:B<x>:MIL1553B:CONDition command.
.data: The TRIGger:A:BUS:B<x>:MIL1553B:DATa command tree.
.errtype: The TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE command.
.status: The TRIGger:A:BUS:B<x>:MIL1553B:STATus command tree.
.time: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe command tree.

parallel `property` ¶

parallel: TriggerABusBItemParallel

Return the TRIGger:A:BUS:B<x>:PARallel command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:PARallel? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:PARallel? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:PARallel:VALue command.

rs232c `property` ¶

rs232c: TriggerABusBItemRs232c

Return the TRIGger:A:BUS:B<x>:RS232C command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:RS232C:CONDition command.
.rx: The TRIGger:A:BUS:B<x>:RS232C:RX command tree.
.tx: The TRIGger:A:BUS:B<x>:RS232C:TX command tree.

spi `property` ¶

spi: TriggerABusBItemSpi

Return the TRIGger:A:BUS:B<x>:SPI command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.condition: The TRIGger:A:BUS:B<x>:SPI:CONDition command.
.data: The TRIGger:A:BUS:B<x>:SPI:DATa command tree.

usb `property` ¶

usb: TriggerABusBItemUsb

Return the TRIGger:A:BUS:B<x>:USB command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.address: The TRIGger:A:BUS:B<x>:USB:ADDRess command tree.
.condition: The TRIGger:A:BUS:B<x>:USB:CONDition command.
.data: The TRIGger:A:BUS:B<x>:USB:DATa command tree.
.endpoint: The TRIGger:A:BUS:B<x>:USB:ENDPoint command tree.
.errtype: The TRIGger:A:BUS:B<x>:USB:ERRTYPE command.
.handshaketype: The TRIGger:A:BUS:B<x>:USB:HANDSHAKEType command.
.qualifier: The TRIGger:A:BUS:B<x>:USB:QUALifier command.
.sofframenumber: The TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber command.
.specialtype: The TRIGger:A:BUS:B<x>:USB:SPECIALType command.
.split: The TRIGger:A:BUS:B<x>:USB:SPLit command tree.
.tokentype: The TRIGger:A:BUS:B<x>:USB:TOKENType command.

TriggerABusBItemArinc429a ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:ARINC429A:CONDition command.
.errtype: The TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE command.
.label: The TRIGger:A:BUS:B<x>:ARINC429A:LABel command tree.
.sdi: The TRIGger:A:BUS:B<x>:ARINC429A:SDI command.
.ssm: The TRIGger:A:BUS:B<x>:ARINC429A:SSM command.

condition `property` ¶

condition: TriggerABusBItemArinc429aCondition

Return the TRIGger:A:BUS:B<x>:ARINC429A:CONDition command.

Description

This command sets the condition (word start, label, matching data, word end, or error) to be used to trigger on CAN bus data. B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:CONDition {STARt|END|LABel|DATA|LABELANDDATA|ERRor}
- TRIGger:A:BUS:B<x>:ARINC429A:CONDition?

Info

STARt enables triggering on the first bit of a word.
END enables triggering on the 32nd bit of a word.
LABel enables trigger on a matching label.
DATA enables triggering on matching packet data field(s).
LABELANDDATA enables triggering on matching label and matching packet data field(s).
ERROR enables triggering on a specified packet error.

errtype `property` ¶

errtype: TriggerABusBItemArinc429aErrtype

Return the TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE command.

Description

This command specifies the error type when triggering on an ARINC429 bus signal. The trigger condition needs to be set to ERROR (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE {ANY|GAP|WORD|PARity}
- TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE?

Info

ANY sets the error type to match any of the other available error types.
GAP sets the error type to match on gap violations (less than 4 bits idle time between two packets on the bus).
WORD sets the error type to match on word errors (incorrect number of bits in a word or bits that violate return to zero transmission).
PARity sets the error type to match on parity errors (parity value results in even parity count for a word).

label `property` ¶

label: TriggerABusBItemArinc429aLabel

Return the TRIGger:A:BUS:B<x>:ARINC429A:LABel command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue command.

sdi `property` ¶

sdi: TriggerABusBItemArinc429aSdi

Return the TRIGger:A:BUS:B<x>:ARINC429A:SDI command.

Description

This command specifies the value for the SDI field to be used when triggering on the ARINC429 bus data field(s). The trigger condition must be set to DATA or LABELANDDATA (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:SDI? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SDI? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SDI value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:SDI <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:SDI?

ssm `property` ¶

ssm: TriggerABusBItemArinc429aSsm

Return the TRIGger:A:BUS:B<x>:ARINC429A:SSM command.

Description

This command specifies the value for the SSM field to be used when triggering on the ARINC429 bus data field(s). The trigger condition must be set to DATA or LABELANDDATA (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:SSM? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SSM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SSM value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:SSM <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:SSM?

TriggerABusBItemArinc429aCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:CONDition command.

Description

This command sets the condition (word start, label, matching data, word end, or error) to be used to trigger on CAN bus data. B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:CONDition {STARt|END|LABel|DATA|LABELANDDATA|ERRor}
- TRIGger:A:BUS:B<x>:ARINC429A:CONDition?

Info

STARt enables triggering on the first bit of a word.
END enables triggering on the 32nd bit of a word.
LABel enables trigger on a matching label.
DATA enables triggering on matching packet data field(s).
LABELANDDATA enables triggering on matching label and matching packet data field(s).
ERROR enables triggering on a specified packet error.

TriggerABusBItemArinc429aErrtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE command.

Description

This command specifies the error type when triggering on an ARINC429 bus signal. The trigger condition needs to be set to ERROR (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE {ANY|GAP|WORD|PARity}
- TRIGger:A:BUS:B<x>:ARINC429A:ERRTYPE?

Info

ANY sets the error type to match any of the other available error types.
GAP sets the error type to match on gap violations (less than 4 bits idle time between two packets on the bus).
WORD sets the error type to match on word errors (incorrect number of bits in a word or bits that violate return to zero transmission).
PARity sets the error type to match on parity errors (parity value results in even parity count for a word).

TriggerABusBItemArinc429aLabel ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:LABel command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemArinc429aLabelHivalue

Return the TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue command.

Description

When the trigger condition is set to LABel, and the qualifier is set to either INrange or OUTrange, this command specifies the upper value of the range for a trigger on the label field. (Use the command TRIGGER:A:BUS:BX:ARINC429A:LABEL:VALUE to specify the lower value of the range). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue?

qualifier `property` ¶

qualifier: TriggerABusBItemArinc429aLabelQualifier

Return the TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier command.

Description

This command specifies the qualifier to be used when triggering on the ARINC429 label field. The trigger condition must be set to LABel or LABELANDDATA. The default qualifier is ‘Equal to’. B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier {LESSthan|MOREthan|Equal|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier?

Info

LESSthan sets label qualifier to less than.
MOREthan sets the label qualifier to greater than.
EQual sets the label qualifier to equal.
UNEQual sets the label qualifier to not equal.
LESSEQual sets the label qualifier to less than or equal.
MOREEQual sets the label qualifier to greater than or equal.
INrange sets the label qualifier to in range.
OUTrange sets the label qualifier to out of range.

value `property` ¶

value: TriggerABusBItemArinc429aLabelValue

Return the TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue command.

Description

This command specifies the low value to be used when triggering on the ARINC429 bus label field. The trigger condition must be set to LABel or LABELANDDATA (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue?

TriggerABusBItemArinc429aLabelHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue command.

Description

When the trigger condition is set to LABel, and the qualifier is set to either INrange or OUTrange, this command specifies the upper value of the range for a trigger on the label field. (Use the command TRIGGER:A:BUS:BX:ARINC429A:LABEL:VALUE to specify the lower value of the range). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:HIVALue?

TriggerABusBItemArinc429aLabelQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier command.

Description

This command specifies the qualifier to be used when triggering on the ARINC429 label field. The trigger condition must be set to LABel or LABELANDDATA. The default qualifier is ‘Equal to’. B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier {LESSthan|MOREthan|Equal|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:QUALifier?

Info

LESSthan sets label qualifier to less than.
MOREthan sets the label qualifier to greater than.
EQual sets the label qualifier to equal.
UNEQual sets the label qualifier to not equal.
LESSEQual sets the label qualifier to less than or equal.
MOREEQual sets the label qualifier to greater than or equal.
INrange sets the label qualifier to in range.
OUTrange sets the label qualifier to out of range.

TriggerABusBItemArinc429aLabelValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue command.

Description

This command specifies the low value to be used when triggering on the ARINC429 bus label field. The trigger condition must be set to LABel or LABELANDDATA (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:LABel:VALue?

TriggerABusBItemArinc429aSdi ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:SDI command.

Description

This command specifies the value for the SDI field to be used when triggering on the ARINC429 bus data field(s). The trigger condition must be set to DATA or LABELANDDATA (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:SDI? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SDI? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SDI value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:SDI <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:SDI?

TriggerABusBItemArinc429aSsm ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ARINC429A:SSM command.

Description

This command specifies the value for the SSM field to be used when triggering on the ARINC429 bus data field(s). The trigger condition must be set to DATA or LABELANDDATA (using TRIGGER:A:BUS:BX:ARINC429A:CONDITION). The default is all X’s (don’t care). B is the bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ARINC429A:SSM? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SSM? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ARINC429A:SSM value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ARINC429A:SSM <QString>
- TRIGger:A:BUS:B<x>:ARINC429A:SSM?

TriggerABusBItemAudio ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:AUDio:CONDition command.
.data: The TRIGger:A:BUS:B<x>:AUDio:DATa command tree.

condition `property` ¶

condition: TriggerABusBItemAudioCondition

Return the TRIGger:A:BUS:B<x>:AUDio:CONDition command.

Description

This command sets the condition (start of frame or matching data) to be used when triggering on an audio bus signal. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:CONDition {SOF|DATA}
- TRIGger:A:BUS:B<x>:AUDio:CONDition?

Info

SOF enables triggering on the start of frame.
DATA enables triggering on matching data.

data `property` ¶

data: TriggerABusBItemAudioData

Return the TRIGger:A:BUS:B<x>:AUDio:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet command.
.qualifier: The TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:AUDio:DATa:VALue command.
.word: The TRIGger:A:BUS:B<x>:AUDio:DATa:WORD command.

TriggerABusBItemAudioCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio:CONDition command.

Description

This command sets the condition (start of frame or matching data) to be used when triggering on an audio bus signal. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:CONDition {SOF|DATA}
- TRIGger:A:BUS:B<x>:AUDio:CONDition?

Info

SOF enables triggering on the start of frame.
DATA enables triggering on matching data.

TriggerABusBItemAudioData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet command.
.qualifier: The TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:AUDio:DATa:VALue command.
.word: The TRIGger:A:BUS:B<x>:AUDio:DATa:WORD command.

hivalue `property` ¶

hivalue: TriggerABusBItemAudioDataHivalue

Return the TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue command.

Description

This command sets the upper word value to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue <String>
- TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue?

offset `property` ¶

offset: TriggerABusBItemAudioDataOffset

Return the TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet command.

Description

This command sets the data offset value to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet?

Info

<NR1> is the data offset value.

qualifier `property` ¶

qualifier: TriggerABusBItemAudioDataQualifier

Return the TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier command.

Description

This command sets the qualifier (<, >, =, <=, >=, not =, in range, out of range) to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier?

Info

LESSthan sets the qualifier to less than.
MOREthan sets the qualifier to greater than.
EQual sets the qualifier to equal.
UNEQual sets the qualifier to not equal.
LESSEQual sets the qualifier to less than or equal.
MOREEQual sets the qualifier to greater than or equal.
INrange sets the qualifier to in range.
OUTrange sets the qualifier to out of range.

value `property` ¶

value: TriggerABusBItemAudioDataValue

Return the TRIGger:A:BUS:B<x>:AUDio:DATa:VALue command.

Description

This command sets the lower word value to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:VALue <String>
- TRIGger:A:BUS:B<x>:AUDio:DATa:VALue?

Info

<String> specifies the trigger data lower word.

word `property` ¶

word: TriggerABusBItemAudioDataWord

Return the TRIGger:A:BUS:B<x>:AUDio:DATa:WORD command.

Description

This command sets the alignment of the data (left, right or either) to be used to trigger on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:WORD? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:WORD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:WORD value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:WORD {EITher|LEFt|RIGht}
- TRIGger:A:BUS:B<x>:AUDio:DATa:WORD?

Info

EITher aligns the trigger data to either left or right.
LEFt aligns the trigger data to the left.
RIGht aligns the trigger data to the right.

TriggerABusBItemAudioDataHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue command.

Description

This command sets the upper word value to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue <String>
- TRIGger:A:BUS:B<x>:AUDio:DATa:HIVALue?

TriggerABusBItemAudioDataOffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet command.

Description

This command sets the data offset value to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:AUDio:DATa:OFFSet?

Info

<NR1> is the data offset value.

TriggerABusBItemAudioDataQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier command.

Description

This command sets the qualifier (<, >, =, <=, >=, not =, in range, out of range) to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:AUDio:DATa:QUALifier?

Info

LESSthan sets the qualifier to less than.
MOREthan sets the qualifier to greater than.
EQual sets the qualifier to equal.
UNEQual sets the qualifier to not equal.
LESSEQual sets the qualifier to less than or equal.
MOREEQual sets the qualifier to greater than or equal.
INrange sets the qualifier to in range.
OUTrange sets the qualifier to out of range.

TriggerABusBItemAudioDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio:DATa:VALue command.

Description

This command sets the lower word value to be used when triggering on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:VALue <String>
- TRIGger:A:BUS:B<x>:AUDio:DATa:VALue?

Info

<String> specifies the trigger data lower word.

TriggerABusBItemAudioDataWord ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:AUDio:DATa:WORD command.

Description

This command sets the alignment of the data (left, right or either) to be used to trigger on an audio bus signal. The trigger condition must be set to DATA using TRIGGER:A:BUS:BX:AUDIO:CONDITION. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:WORD? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:WORD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:AUDio:DATa:WORD value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:AUDio:DATa:WORD {EITher|LEFt|RIGht}
- TRIGger:A:BUS:B<x>:AUDio:DATa:WORD?

Info

EITher aligns the trigger data to either left or right.
LEFt aligns the trigger data to the left.
RIGht aligns the trigger data to the right.

TriggerABusBItemCan ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:CAN:CONDition command.
.data: The TRIGger:A:BUS:B<x>:CAN:DATa command tree.
.fd: The TRIGger:A:BUS:B<x>:CAN:FD command tree.
.frametype: The TRIGger:A:BUS:B<x>:CAN:FRAMEtype command.
.identifier: The TRIGger:A:BUS:B<x>:CAN:IDentifier command tree.
.address: The TRIGger:A:BUS:B<x>:CAN:ADDRess command tree.

address `property` ¶

address: TriggerABusBItemCanAddress

Return the TRIGger:A:BUS:B<x>:CAN:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.mode: The TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe command.
.value: The TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue command.

condition `property` ¶

condition: TriggerABusBItemCanCondition

Return the TRIGger:A:BUS:B<x>:CAN:CONDition command.

Description

This command sets the condition (start of frame, frame type, identifier, matching data, end of frame, missing ACK field, bit-stuffing error, form error, any error, CAN FD BRS bit, or CAN FD ESI bit) to be used to search on CAN bus data. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:CONDition {SOF|FRAMEtype|IDentifier|DATA|IDANDDATA|EOF|ACKMISS|ERROR|FORMERRor|ANYERRor|FDBRS|FDESI}
- TRIGger:A:BUS:B<x>:CAN:CONDition?

Info

SOF enables triggering on the start of frame.
FRAMEtype enables triggering on the type of frame.
IDentifier enables triggering on a matching identifier.
DATA enables triggering on matching data.
IDANDDATA enables triggering on a matching identifier and matching data.
EOF enables triggering on the end of frame.
ACKMISS enables triggering on a missing acknowledge.
ERROR enables triggering on bit stuffing errors.
FORMERRor enables triggering on packet form errors.
ANYERRor enables triggering on any packet error (missing ACK, bit stuffing error, or form error).
FDBRS enables triggering on a CAN FD frame’s BRS bit.
FDESI enables triggering on a CAN FD frame’s ESI bit.

data `property` ¶

data: TriggerABusBItemCanData

Return the TRIGger:A:BUS:B<x>:CAN:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.direction: The TRIGger:A:BUS:B<x>:CAN:DATa:DIRection command.
.offset: The TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet command.
.qualifier: The TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier command.
.size: The TRIGger:A:BUS:B<x>:CAN:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:CAN:DATa:VALue command.

fd `property` ¶

fd: TriggerABusBItemCanFd

Return the TRIGger:A:BUS:B<x>:CAN:FD command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FD? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.brsbit: The TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT command.
.esibit: The TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT command.

frametype `property` ¶

frametype: TriggerABusBItemCanFrametype

Return the TRIGger:A:BUS:B<x>:CAN:FRAMEtype command.

Description

This command sets the frame type (data, remote, error or overload) to be used when triggering on a CAN bus signal. The trigger condition must be set to FRAMEtype (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FRAMEtype? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FRAMEtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:FRAMEtype value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:FRAMEtype {DATA|REMote|ERRor|OVERLoad}
- TRIGger:A:BUS:B<x>:CAN:FRAMEtype?

Info

DATA specifies a data frame type.
REMote specifies a remote frame type.
ERRor specifies an error frame type.
OVERLold specifies an overload frame type.

identifier `property` ¶

identifier: TriggerABusBItemCanIdentifier

Return the TRIGger:A:BUS:B<x>:CAN:IDentifier command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.mode: The TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe command.
.value: The TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue command.

TriggerABusBItemCanAddress ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess? query and raise an AssertionError if the returned value does not match value.

Properties

.mode: The TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe command.
.value: The TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue command.

mode `property` ¶

mode: TriggerABusBItemCanAddressMode

Return the TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe command.

Description

This command sets the addressing mode (standard or extended format) to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe {STandard|EXTENDed}
- TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe?

Info

STandard specifies the standard addressing mode.
EXTENDed specifies the extended addressing mode.

value `property` ¶

value: TriggerABusBItemCanAddressValue

Return the TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue command.

Description

This command sets the binary address value to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue?

Info

<QString> is up to 29 bits specifying the binary identifier value. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemCanAddressMode ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe command.

Description

This command sets the addressing mode (standard or extended format) to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe {STandard|EXTENDed}
- TRIGger:A:BUS:B<x>:CAN:ADDRess:MODe?

Info

STandard specifies the standard addressing mode.
EXTENDed specifies the extended addressing mode.

TriggerABusBItemCanAddressValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue command.

Description

This command sets the binary address value to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:ADDRess:VALue?

Info

<QString> is up to 29 bits specifying the binary identifier value. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemCanCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:CONDition command.

Description

This command sets the condition (start of frame, frame type, identifier, matching data, end of frame, missing ACK field, bit-stuffing error, form error, any error, CAN FD BRS bit, or CAN FD ESI bit) to be used to search on CAN bus data. B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:CONDition {SOF|FRAMEtype|IDentifier|DATA|IDANDDATA|EOF|ACKMISS|ERROR|FORMERRor|ANYERRor|FDBRS|FDESI}
- TRIGger:A:BUS:B<x>:CAN:CONDition?

Info

SOF enables triggering on the start of frame.
FRAMEtype enables triggering on the type of frame.
IDentifier enables triggering on a matching identifier.
DATA enables triggering on matching data.
IDANDDATA enables triggering on a matching identifier and matching data.
EOF enables triggering on the end of frame.
ACKMISS enables triggering on a missing acknowledge.
ERROR enables triggering on bit stuffing errors.
FORMERRor enables triggering on packet form errors.
ANYERRor enables triggering on any packet error (missing ACK, bit stuffing error, or form error).
FDBRS enables triggering on a CAN FD frame’s BRS bit.
FDESI enables triggering on a CAN FD frame’s ESI bit.

TriggerABusBItemCanData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.direction: The TRIGger:A:BUS:B<x>:CAN:DATa:DIRection command.
.offset: The TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet command.
.qualifier: The TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier command.
.size: The TRIGger:A:BUS:B<x>:CAN:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:CAN:DATa:VALue command.

direction `property` ¶

direction: TriggerABusBItemCanDataDirection

Return the TRIGger:A:BUS:B<x>:CAN:DATa:DIRection command.

Description

This command sets the data direction (read, write or ‘nocare’) to be used to search on a CAN bus signal. The trigger condition must be set to IDentifier (using TRIGGER:A:BUS:BX:CAN:CONDITION). The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:DIRection? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:DIRection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:DIRection value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:DIRection {READ|WRITE|NOCARE}
- TRIGger:A:BUS:B<x>:CAN:DATa:DIRection?

Info

READ sets the CAN data direction to READ.
WRITE sets the CAN data direction to WRITE.
NOCARE sets the CAN data direction to either.

offset `property` ¶

offset: TriggerABusBItemCanDataOffset

Return the TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet command.

Description

This command sets or queries the data offset value, in bytes, to use when triggering on the CAN data field. The bus number is specified by x. The trigger condition must be set to DATA or IDANDDATA.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet?

Info

<NR1> is an integer whose minimum and default values are -1 (don’t care), and the maximum is up to 7 (for CAN 2.0) or up to 63 (for ISO CAN FD and Non-ISO CAN FD).

qualifier `property` ¶

qualifier: TriggerABusBItemCanDataQualifier

Return the TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier command.

Description

This command sets the qualifier (<, >, =, not =, <=) to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier {LESSthan|Than|EQual|UNEQual|LESSEQual|EQual}
- TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier?

Info

LESSthan sets the oscilloscope to trigger when the data is less than the qualifier value.
Than sets the oscilloscope to trigger when the data is than the qualifier value.
EQual sets the oscilloscope to trigger when the data is equal to the qualifier value.
UNEQual sets the oscilloscope to trigger when the data is not equal to the qualifier value.
LESSEQual sets the oscilloscope to trigger when the data is less than or equal to the qualifier value.
EQual sets the oscilloscope to trigger when the data is than or equal to the qualifier value.

size `property` ¶

size: TriggerABusBItemCanDataSize

Return the TRIGger:A:BUS:B<x>:CAN:DATa:SIZe command.

Description

This command sets the length of the data string, in bytes, to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA or DATa (using TRIGGER:A:BUS:BX:CAN:CONDITION). The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:CAN:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

value `property` ¶

value: TriggerABusBItemCanDataValue

Return the TRIGger:A:BUS:B<x>:CAN:DATa:VALue command.

Description

This command sets the binary data value to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA or DATa (using TRIGGER:A:BUS:BX:CAN:CONDITION). The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:DATa:VALue?

Info

<QString> is the data value in binary format. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemCanDataDirection ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:DATa:DIRection command.

Description

This command sets the data direction (read, write or ‘nocare’) to be used to search on a CAN bus signal. The trigger condition must be set to IDentifier (using TRIGGER:A:BUS:BX:CAN:CONDITION). The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:DIRection? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:DIRection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:DIRection value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:DIRection {READ|WRITE|NOCARE}
- TRIGger:A:BUS:B<x>:CAN:DATa:DIRection?

Info

READ sets the CAN data direction to READ.
WRITE sets the CAN data direction to WRITE.
NOCARE sets the CAN data direction to either.

TriggerABusBItemCanDataOffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet command.

Description

This command sets or queries the data offset value, in bytes, to use when triggering on the CAN data field. The bus number is specified by x. The trigger condition must be set to DATA or IDANDDATA.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet?

Info

<NR1> is an integer whose minimum and default values are -1 (don’t care), and the maximum is up to 7 (for CAN 2.0) or up to 63 (for ISO CAN FD and Non-ISO CAN FD).

TriggerABusBItemCanDataQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier command.

Description

This command sets the qualifier (<, >, =, not =, <=) to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier {LESSthan|Than|EQual|UNEQual|LESSEQual|EQual}
- TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier?

Info

LESSthan sets the oscilloscope to trigger when the data is less than the qualifier value.
Than sets the oscilloscope to trigger when the data is than the qualifier value.
EQual sets the oscilloscope to trigger when the data is equal to the qualifier value.
UNEQual sets the oscilloscope to trigger when the data is not equal to the qualifier value.
LESSEQual sets the oscilloscope to trigger when the data is less than or equal to the qualifier value.
EQual sets the oscilloscope to trigger when the data is than or equal to the qualifier value.

TriggerABusBItemCanDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:DATa:SIZe command.

Description

This command sets the length of the data string, in bytes, to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA or DATa (using TRIGGER:A:BUS:BX:CAN:CONDITION). The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:CAN:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

TriggerABusBItemCanDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:DATa:VALue command.

Description

This command sets the binary data value to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA or DATa (using TRIGGER:A:BUS:BX:CAN:CONDITION). The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:DATa:VALue?

Info

<QString> is the data value in binary format. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemCanFd ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:FD command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FD? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD? query and raise an AssertionError if the returned value does not match value.

Properties

.brsbit: The TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT command.
.esibit: The TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT command.

brsbit `property` ¶

brsbit: TriggerABusBItemCanFdBrsbit

Return the TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT command.

Description

This command specifies the binary data value to be used to search on CAN FD BRS bits. This only applies if the search condition has been set to FDBRSBIT (using TRIGger:A:BUS:B<x>:CAN:CONDition ). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT {ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
- TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT?

Info

ZERo , OFF, and 0 specify that the BRS bit must have value 0. If queried, the command will always return 0 if set with these arguments.
ONE , ON, and 1 specify that the BRS bit must have value 1. If queried, the command will always return 1 if set with these arguments.
NOCARE , X, and x specify that the BRS bit may be either 1 or 0. If queried, the command will always return X if set with these arguments.

esibit `property` ¶

esibit: TriggerABusBItemCanFdEsibit

Return the TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT command.

Description

This command specifies the binary data value to be used to search on CAN FD ESI bits. This only applies if the search condition has been set to FDESIBIT (using TRIGger:A:BUS:B<x>:CAN:CONDition ). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT {ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
- TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT?

Info

ZERo , OFF, and 0 specify that the BRS bit must have value 0. If queried, the command will always return 0 if set with these arguments.
ONE , ON, and 1 specify that the BRS bit must have value 1. If queried, the command will always return 1 if set with these arguments.
NOCARE , X, and x specify that the BRS bit may be either 1 or 0. If queried, the command will always return X if set with these arguments.

TriggerABusBItemCanFdBrsbit ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT command.

Description

This command specifies the binary data value to be used to search on CAN FD BRS bits. This only applies if the search condition has been set to FDBRSBIT (using TRIGger:A:BUS:B<x>:CAN:CONDition ). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT {ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
- TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT?

Info

ZERo , OFF, and 0 specify that the BRS bit must have value 0. If queried, the command will always return 0 if set with these arguments.
ONE , ON, and 1 specify that the BRS bit must have value 1. If queried, the command will always return 1 if set with these arguments.
NOCARE , X, and x specify that the BRS bit may be either 1 or 0. If queried, the command will always return X if set with these arguments.

TriggerABusBItemCanFdEsibit ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT command.

Description

This command specifies the binary data value to be used to search on CAN FD ESI bits. This only applies if the search condition has been set to FDESIBIT (using TRIGger:A:BUS:B<x>:CAN:CONDition ). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT {ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
- TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT?

Info

ZERo , OFF, and 0 specify that the BRS bit must have value 0. If queried, the command will always return 0 if set with these arguments.
ONE , ON, and 1 specify that the BRS bit must have value 1. If queried, the command will always return 1 if set with these arguments.
NOCARE , X, and x specify that the BRS bit may be either 1 or 0. If queried, the command will always return X if set with these arguments.

TriggerABusBItemCanFrametype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:FRAMEtype command.

Description

This command sets the frame type (data, remote, error or overload) to be used when triggering on a CAN bus signal. The trigger condition must be set to FRAMEtype (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:FRAMEtype? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:FRAMEtype? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:FRAMEtype value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:FRAMEtype {DATA|REMote|ERRor|OVERLoad}
- TRIGger:A:BUS:B<x>:CAN:FRAMEtype?

Info

DATA specifies a data frame type.
REMote specifies a remote frame type.
ERRor specifies an error frame type.
OVERLold specifies an overload frame type.

TriggerABusBItemCanIdentifier ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:IDentifier command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier? query and raise an AssertionError if the returned value does not match value.

Properties

.mode: The TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe command.
.value: The TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue command.

mode `property` ¶

mode: TriggerABusBItemCanIdentifierMode

Return the TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe command.

Description

This command sets the addressing mode (standard or extended format) to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe {STandard|EXTENDed}
- TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe?

Info

STandard specifies the standard addressing mode.
EXTENDed specifies the extended addressing mode.

value `property` ¶

value: TriggerABusBItemCanIdentifierValue

Return the TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue command.

Description

This command sets the binary address value to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue?

Info

<QString> is up to 29 bits specifying the binary identifier value. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemCanIdentifierMode ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe command.

Description

This command sets the addressing mode (standard or extended format) to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe {STandard|EXTENDed}
- TRIGger:A:BUS:B<x>:CAN:IDentifier:MODe?

Info

STandard specifies the standard addressing mode.
EXTENDed specifies the extended addressing mode.

TriggerABusBItemCanIdentifierValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue command.

Description

This command sets the binary address value to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDATA OR DATA (using TRIGGER:A:BUS:BX:CAN:CONDITION). B is the bus number (1-2).

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue <QString>
- TRIGger:A:BUS:B<x>:CAN:IDentifier:VALue?

Info

<QString> is up to 29 bits specifying the binary identifier value. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemEthernet ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:ETHERnet:CONDition command.
.data: The TRIGger:A:BUS:B<x>:ETHERnet:DATa command tree.
.frametype: The TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe command.
.ipheader: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader command tree.
.mac: The TRIGger:A:BUS:B<x>:ETHERnet:MAC command tree.
.qtag: The TRIGger:A:BUS:B<x>:ETHERnet:QTAG command tree.
.qualifier: The TRIGger:A:BUS:B<x>:ETHERnet:QUALifier command.
.tcpheader: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader command tree.

condition `property` ¶

condition: TriggerABusBItemEthernetCondition

Return the TRIGger:A:BUS:B<x>:ETHERnet:CONDition command.

Description

This command specifies a field or condition within an Ethernet frame to trigger on. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:CONDition {SFD|MACADDRess|MACLENgth|IPHeader|TCPHeader|DATa|EOP|IDLe|FCSError|QTAG}
- TRIGger:A:BUS:B<x>:ETHERnet:CONDition?

Info

SFD - Start of frame delimiter.
MACADDRess - MAC addresses field.
MACLENgth - MAC length/type field.
IPHeader - IP header field. This argument is only available when PROTOCOL is set to IPv4 (using the command BUS:BX:ETHERNET:PROTOCOL).
TCPHeader - TCP header field. This argument is only available when PROTOCOL is set to IPv4 (using the command BUS:BX:ETHERNET:PROTOCOL).
DATa - TCP/IPv4 or MAC protocol client data field. Use the command BUS:BX:ETHERNET:PROTOCOL to specify either TCP/IPv4 or OTHER. If the protocol is set to OTHER, then DATa refers to the MAC client data.
EOP - End of Packet field.
IDLe - Idle field.
FCSError - Frame Check Sequence Error (CRC) field.
QTAG - IEEE 802.1Q (VLAN) control information field. In order to use QTAG as a trigger condition, the frame type must be set to QTAG (using TRIGGER:A:BUS:BX:ETHERNET:FRAMETYPE ).

data `property` ¶

data: TriggerABusBItemEthernetData

Return the TRIGger:A:BUS:B<x>:ETHERnet:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet command.
.size: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue command.

frametype `property` ¶

frametype: TriggerABusBItemEthernetFrametype

Return the TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe command.

Description

This command specifies the Ethernet frame type: either Basic or QTag (IEEE 802.1Q, or VLAN tagging). The default is Basic. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe {BASic|QTAG}
- TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe?

Info

BASic is the standard Ethernet frame.
QTAG is the Q-Tag Ethernet frame (also called VLAN tagging.).

ipheader `property` ¶

ipheader: TriggerABusBItemEthernetIpheader

Return the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.destinationaddr: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr command tree.
.protocol: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol command tree.
.sourceaddr: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr command tree.

mac `property` ¶

mac: TriggerABusBItemEthernetMac

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.address: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess command tree.
.length: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth command tree.
.type: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe command tree.

qtag `property` ¶

qtag: TriggerABusBItemEthernetQtag

Return the TRIGger:A:BUS:B<x>:ETHERnet:QTAG command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue command.

qualifier `property` ¶

qualifier: TriggerABusBItemEthernetQualifier

Return the TRIGger:A:BUS:B<x>:ETHERnet:QUALifier command.

Description

This command specifies the qualifier to be used when the Ethernet trigger condition is set to MACLENgth or DATa. Normally, the Ethernet qualifier is set to ‘Equal to’. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:ETHERnet:QUALifier?

tcpheader `property` ¶

tcpheader: TriggerABusBItemEthernetTcpheader

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.acknum: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum command tree.
.destinationport: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport command tree.
.seqnum: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum command tree.
.sourceport: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport command tree.

TriggerABusBItemEthernetCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:CONDition command.

Description

This command specifies a field or condition within an Ethernet frame to trigger on. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:CONDition {SFD|MACADDRess|MACLENgth|IPHeader|TCPHeader|DATa|EOP|IDLe|FCSError|QTAG}
- TRIGger:A:BUS:B<x>:ETHERnet:CONDition?

Info

SFD - Start of frame delimiter.
MACADDRess - MAC addresses field.
MACLENgth - MAC length/type field.
IPHeader - IP header field. This argument is only available when PROTOCOL is set to IPv4 (using the command BUS:BX:ETHERNET:PROTOCOL).
TCPHeader - TCP header field. This argument is only available when PROTOCOL is set to IPv4 (using the command BUS:BX:ETHERNET:PROTOCOL).
DATa - TCP/IPv4 or MAC protocol client data field. Use the command BUS:BX:ETHERNET:PROTOCOL to specify either TCP/IPv4 or OTHER. If the protocol is set to OTHER, then DATa refers to the MAC client data.
EOP - End of Packet field.
IDLe - Idle field.
FCSError - Frame Check Sequence Error (CRC) field.
QTAG - IEEE 802.1Q (VLAN) control information field. In order to use QTAG as a trigger condition, the frame type must be set to QTAG (using TRIGGER:A:BUS:BX:ETHERNET:FRAMETYPE ).

TriggerABusBItemEthernetData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet command.
.size: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemEthernetDataHivalue

Return the TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue command.

Description

When the Ethernet trigger condition is set to DATa, and the qualifier is set to either INrange or OUTrange, this command specifies the upper data value of the range. (Use the command TRIGGER:A:BUS:BX:ETHERNET:DATA:VALUE to specify the lower limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue?

offset `property` ¶

offset: TriggerABusBItemEthernetDataOffset

Return the TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet command.

Description

When the Ethernet trigger condition is set to DATa, this command specifies where in the data field to look for the data trigger value. It specifies the offset into the data field, in bytes, where the value will be matched. The default is -1 (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet?

Info

<NR1> is an integer whose minimum and default values are -1 (don’t care) and maximum is 1,499.

size `property` ¶

size: TriggerABusBItemEthernetDataSize

Return the TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe command.

Description

When the Ethernet trigger condition is set to DATa, this command specifies the number of contiguous TCP/IPv4/MAC client data bytes to trigger on. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe?

value `property` ¶

value: TriggerABusBItemEthernetDataValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue command.

Description

When the Ethernet trigger condition is set to DATa, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the value to trigger on. When the Ethernet trigger condition is set to DATa, and the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command TRIGGER:A:BUS:BX:ETHERNET:DATA:HIVALUE to set the upper limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue?

TriggerABusBItemEthernetDataHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue command.

Description

When the Ethernet trigger condition is set to DATa, and the qualifier is set to either INrange or OUTrange, this command specifies the upper data value of the range. (Use the command TRIGGER:A:BUS:BX:ETHERNET:DATA:VALUE to specify the lower limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:HIVALue?

TriggerABusBItemEthernetDataOffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet command.

Description

When the Ethernet trigger condition is set to DATa, this command specifies where in the data field to look for the data trigger value. It specifies the offset into the data field, in bytes, where the value will be matched. The default is -1 (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:OFFSet?

Info

<NR1> is an integer whose minimum and default values are -1 (don’t care) and maximum is 1,499.

TriggerABusBItemEthernetDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe command.

Description

When the Ethernet trigger condition is set to DATa, this command specifies the number of contiguous TCP/IPv4/MAC client data bytes to trigger on. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:SIZe?

TriggerABusBItemEthernetDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue command.

Description

When the Ethernet trigger condition is set to DATa, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the value to trigger on. When the Ethernet trigger condition is set to DATa, and the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command TRIGGER:A:BUS:BX:ETHERNET:DATA:HIVALUE to set the upper limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:DATa:VALue?

TriggerABusBItemEthernetFrametype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe command.

Description

This command specifies the Ethernet frame type: either Basic or QTag (IEEE 802.1Q, or VLAN tagging). The default is Basic. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe {BASic|QTAG}
- TRIGger:A:BUS:B<x>:ETHERnet:FRAMETYPe?

Info

BASic is the standard Ethernet frame.
QTAG is the Q-Tag Ethernet frame (also called VLAN tagging.).

TriggerABusBItemEthernetIpheader ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader? query and raise an AssertionError if the returned value does not match value.

Properties

.destinationaddr: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr command tree.
.protocol: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol command tree.
.sourceaddr: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr command tree.

destinationaddr `property` ¶

destinationaddr: TriggerABusBItemEthernetIpheaderDestinationaddr

Return the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue command.

protocol `property` ¶

protocol: TriggerABusBItemEthernetIpheaderProtocol

Return the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue command.

sourceaddr `property` ¶

sourceaddr: TriggerABusBItemEthernetIpheaderSourceaddr

Return the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue command.

TriggerABusBItemEthernetIpheaderDestinationaddr ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetIpheaderDestinationaddrValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue command.

Description

When the Ethernet trigger condition is set to IPHeader, this command specifies the value of the 32-bit destination address that is to be used in the trigger (along with the source address and protocol value). The IP destination address is a standard IP address such as 192.168.0.1. The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue?

TriggerABusBItemEthernetIpheaderDestinationaddrValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue command.

Description

When the Ethernet trigger condition is set to IPHeader, this command specifies the value of the 32-bit destination address that is to be used in the trigger (along with the source address and protocol value). The IP destination address is a standard IP address such as 192.168.0.1. The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:DESTinationaddr:VALue?

TriggerABusBItemEthernetIpheaderProtocol ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetIpheaderProtocolValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue command.

Description

When the Ethernet trigger condition is set to IPHeader, this command specifies the value of the 8-bit protocol field that is to be used in the trigger (along with the source and destination addresses). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue?

TriggerABusBItemEthernetIpheaderProtocolValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue command.

Description

When the Ethernet trigger condition is set to IPHeader, this command specifies the value of the 8-bit protocol field that is to be used in the trigger (along with the source and destination addresses). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:PROTOcol:VALue?

TriggerABusBItemEthernetIpheaderSourceaddr ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetIpheaderSourceaddrValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue command.

Description

When the Ethernet trigger condition is set to IPHeader, this command specifies the value of the 32-bit source address that is to be used in the trigger (along with the destination address and protocol value). The IP source address is a standard IP address such as 192.168.0.1. The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue?

TriggerABusBItemEthernetIpheaderSourceaddrValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue command.

Description

When the Ethernet trigger condition is set to IPHeader, this command specifies the value of the 32-bit source address that is to be used in the trigger (along with the destination address and protocol value). The IP source address is a standard IP address such as 192.168.0.1. The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:IPHeader:SOUrceaddr:VALue?

TriggerABusBItemEthernetMac ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC? query and raise an AssertionError if the returned value does not match value.

Properties

.address: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess command tree.
.length: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth command tree.
.type: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe command tree.

address `property` ¶

address: TriggerABusBItemEthernetMacAddress

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.destination: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination command tree.
.source: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce command tree.

length `property` ¶

length: TriggerABusBItemEthernetMacLength

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue command.
.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue command.

type `property` ¶

type: TriggerABusBItemEthernetMacType

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue command.
.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue command.

TriggerABusBItemEthernetMacAddress ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess? query and raise an AssertionError if the returned value does not match value.

Properties

.destination: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination command tree.
.source: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce command tree.

destination `property` ¶

destination: TriggerABusBItemEthernetMacAddressDestination

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue command.

source `property` ¶

source: TriggerABusBItemEthernetMacAddressSource

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue command.

TriggerABusBItemEthernetMacAddressDestination ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetMacAddressDestinationValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue command.

Description

When the Ethernet trigger condition is set to MACADDress, this command specifies the 48-bit MAC destination address that is to be used in the trigger (along with the source address value). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue?

TriggerABusBItemEthernetMacAddressDestinationValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue command.

Description

When the Ethernet trigger condition is set to MACADDress, this command specifies the 48-bit MAC destination address that is to be used in the trigger (along with the source address value). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:DESTination:VALue?

TriggerABusBItemEthernetMacAddressSource ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetMacAddressSourceValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue command.

Description

When the Ethernet trigger condition is set to MACADDress, this command specifies the 48-bit MAC source address value that is to be used in the trigger (along with the destination address value). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue?

TriggerABusBItemEthernetMacAddressSourceValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue command.

Description

When the Ethernet trigger condition is set to MACADDress, this command specifies the 48-bit MAC source address value that is to be used in the trigger (along with the destination address value). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:ADDRess:SOUrce:VALue?

TriggerABusBItemEthernetMacLength ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue command.
.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemEthernetMacLengthHivalue

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to INrange or OUTrange, this command specifies the upper data value of the range. (Use the command to specify the lower limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue?

value `property` ¶

value: TriggerABusBItemEthernetMacLengthValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the 16-bit value to trigger on. When the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command to set the upper limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue?

TriggerABusBItemEthernetMacLengthHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to INrange or OUTrange, this command specifies the upper data value of the range. (Use the command to specify the lower limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:HIVALue?

TriggerABusBItemEthernetMacLengthValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the 16-bit value to trigger on. When the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command to set the upper limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:LENgth:VALue?

TriggerABusBItemEthernetMacType ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue command.
.value: The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemEthernetMacTypeHivalue

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to INrange or OUTrange, this command specifies the upper data value of the range. (Use the command to specify the lower limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue?

value `property` ¶

value: TriggerABusBItemEthernetMacTypeValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the 16-bit value to trigger on. When the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command to set the upper limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue?

TriggerABusBItemEthernetMacTypeHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to INrange or OUTrange, this command specifies the upper data value of the range. (Use the command to specify the lower limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:HIVALue?

TriggerABusBItemEthernetMacTypeValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue command.

Description

When the Ethernet trigger condition is set to MACLENgth, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the 16-bit value to trigger on. When the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command to set the upper limit of the range.) The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:MAC:TYPe:VALue?

TriggerABusBItemEthernetQtag ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:QTAG command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetQtagValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue command.

Description

When the Ethernet trigger condition is set to QTAG, this command specifies the 32-bit Q-Tag value to trigger on. The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue?

TriggerABusBItemEthernetQtagValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue command.

Description

When the Ethernet trigger condition is set to QTAG, this command specifies the 32-bit Q-Tag value to trigger on. The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:QTAG:VALue?

TriggerABusBItemEthernetQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:QUALifier command.

Description

This command specifies the qualifier to be used when the Ethernet trigger condition is set to MACLENgth or DATa. Normally, the Ethernet qualifier is set to ‘Equal to’. B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:ETHERnet:QUALifier?

TriggerABusBItemEthernetTcpheader ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader? query and raise an AssertionError if the returned value does not match value.

Properties

.acknum: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum command tree.
.destinationport: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport command tree.
.seqnum: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum command tree.
.sourceport: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport command tree.

acknum `property` ¶

acknum: TriggerABusBItemEthernetTcpheaderAcknum

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue command.

destinationport `property` ¶

destinationport: TriggerABusBItemEthernetTcpheaderDestinationport

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue command.

seqnum `property` ¶

seqnum: TriggerABusBItemEthernetTcpheaderSeqnum

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue command.

sourceport `property` ¶

sourceport: TriggerABusBItemEthernetTcpheaderSourceport

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue command.

TriggerABusBItemEthernetTcpheaderAcknum ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetTcpheaderAcknumValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue command.

Description

When the Ethernet trigger condition is set to TCPHeader, this command specifies the 32-bit acknowledgement number that is to be used in the trigger (along with the destination and source port addresses and the sequence number). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue?

TriggerABusBItemEthernetTcpheaderAcknumValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue command.

Description

When the Ethernet trigger condition is set to TCPHeader, this command specifies the 32-bit acknowledgement number that is to be used in the trigger (along with the destination and source port addresses and the sequence number). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:ACKnum:VALue?

TriggerABusBItemEthernetTcpheaderDestinationport ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetTcpheaderDestinationportValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue command.

Description

When the Ethernet trigger condition is set TCPHeader, this command specifies the 16-bit destination port address value that is to be used in the trigger (along with the acknowledgement value, source port address and the sequence number). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue?

TriggerABusBItemEthernetTcpheaderDestinationportValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue command.

Description

When the Ethernet trigger condition is set TCPHeader, this command specifies the 16-bit destination port address value that is to be used in the trigger (along with the acknowledgement value, source port address and the sequence number). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:DESTinationport:VALue?

TriggerABusBItemEthernetTcpheaderSeqnum ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetTcpheaderSeqnumValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue command.

Description

When the Ethernet trigger condition is set to TCPHeader, this command specifies the 32-bit sequence number that is to be used in the trigger (along with the destination and source port addresses and the acknowledgement value). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue?

TriggerABusBItemEthernetTcpheaderSeqnumValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue command.

Description

When the Ethernet trigger condition is set to TCPHeader, this command specifies the 32-bit sequence number that is to be used in the trigger (along with the destination and source port addresses and the acknowledgement value). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SEQnum:VALue?

TriggerABusBItemEthernetTcpheaderSourceport ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue command.

value `property` ¶

value: TriggerABusBItemEthernetTcpheaderSourceportValue

Return the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue command.

Description

When the Ethernet trigger condition is set to TCPHeader, this command specifies the 16-bit source port address that is to be used in the trigger (along with the destination port address, the sequence number and the acknowledgement number). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue?

TriggerABusBItemEthernetTcpheaderSourceportValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue command.

Description

When the Ethernet trigger condition is set to TCPHeader, this command specifies the 16-bit source port address that is to be used in the trigger (along with the destination port address, the sequence number and the acknowledgement number). The default is all X’s (don’t care). B is the bus number B1-B4.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue <QString>
- TRIGger:A:BUS:B<x>:ETHERnet:TCPHeader:SOUrceport:VALue?

TriggerABusBItemFlexray ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:FLEXray:CONDition command.
.cyclecount: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount command tree.
.data: The TRIGger:A:BUS:B<x>:FLEXray:DATa command tree.
.eoftype: The TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE command.
.errtype: The TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE command.
.frameid: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID command tree.
.frametype: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEType command.
.header: The TRIGger:A:BUS:B<x>:FLEXray:HEADER command tree.

condition `property` ¶

condition: TriggerABusBItemFlexrayCondition

Return the TRIGger:A:BUS:B<x>:FLEXray:CONDition command.

Description

This command specifies the condition to use when triggering on a FlexRay bus signal (start of frame, frame type, ID, cycle count, header, data, ID and data, EOF, error). B is the bus number B1-B2.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CONDition {SOF|FRAMEType|IDentifier|CYCLEcount|HEADer|DATA|IDANDDATA|EOF|ERROR}
- TRIGger:A:BUS:B<x>:FLEXray:CONDition?

Info

SOF sets the trigger condition to start of frame.
FRAMEType sets the trigger condition to frame type.
IDentifier sets the trigger condition to identifier.
CYCLEcount sets the trigger condition to cycle count.
HEADer sets the trigger condition to header.
DATA sets the trigger condition to data.
IDANDDATA sets the trigger condition to id and data.
EOF sets the trigger condition to end of frame.
ERROR sets the trigger condition to error.

cyclecount `property` ¶

cyclecount: TriggerABusBItemFlexrayCyclecount

Return the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue command.

data `property` ¶

data: TriggerABusBItemFlexrayData

Return the TRIGger:A:BUS:B<x>:FLEXray:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet command.
.qualifier: The TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier command.
.size: The TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue command.

eoftype `property` ¶

eoftype: TriggerABusBItemFlexrayEoftype

Return the TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE command.

Description

This command specifies the end of file type (static, dynamic or any) when triggering on the FlexRay bus EOF field. The trigger condition needs to be set to EOF (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE {STATic|DYNAMic|ANY}
- TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE?

Info

STATic specifies triggering on the STATIC end of file type.
DYNAMic specifies triggering on the DYNAMIC end of file type.
ANY specifies triggering on a STATIC or DYNAMIC end of file type.

errtype `property` ¶

errtype: TriggerABusBItemFlexrayErrtype

Return the TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE command.

Description

This command specifies the error type when triggering on the FlexRay bus signal. The trigger condition needs to be set to ERROR (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE {CRCHeader|CRCTrailer|SYNCFrame|STARTupnosync|NULLFRStatic|NULLFRDynamic}
- TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE?

Info

CRCHeader sets the error type to CRCHeader.
CRCTrailer sets the error type to CRCTrailer.
SYNCFrame sets the error type to SYNCFrame.
STARTupnosync sets the error type to STARTupnosync.
NULLFRStatic sets the error type to NULLFRStatic.
NULLFRDynamic sets the error type to NULLFRDynamic.

frameid `property` ¶

frameid: TriggerABusBItemFlexrayFrameid

Return the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue command.

frametype `property` ¶

frametype: TriggerABusBItemFlexrayFrametype

Return the TRIGger:A:BUS:B<x>:FLEXray:FRAMEType command.

Description

This command specifies the frame type (normal, payload, null, sync or startup) when triggering on the FlexRay bus signal. The trigger condition needs to be set to FRAMEType (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEType {NORMal|PAYLoad|NULL|SYNC|STARTup}
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEType?

Info

NORMal specifies the normal frame type.
PAYLoad specifies the payload frame type.
NULL specifies the null frame type.
SYNC specifies the sync frame type.
STARTup specifies the startup frame type.

header `property` ¶

header: TriggerABusBItemFlexrayHeader

Return the TRIGger:A:BUS:B<x>:FLEXray:HEADER command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.crc: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC command.
.cyclecount: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount command.
.frameid: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID command.
.indbits: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits command.
.paylength: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength command.

TriggerABusBItemFlexrayCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:CONDition command.

Description

This command specifies the condition to use when triggering on a FlexRay bus signal (start of frame, frame type, ID, cycle count, header, data, ID and data, EOF, error). B is the bus number B1-B2.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CONDition {SOF|FRAMEType|IDentifier|CYCLEcount|HEADer|DATA|IDANDDATA|EOF|ERROR}
- TRIGger:A:BUS:B<x>:FLEXray:CONDition?

Info

SOF sets the trigger condition to start of frame.
FRAMEType sets the trigger condition to frame type.
IDentifier sets the trigger condition to identifier.
CYCLEcount sets the trigger condition to cycle count.
HEADer sets the trigger condition to header.
DATA sets the trigger condition to data.
IDANDDATA sets the trigger condition to id and data.
EOF sets the trigger condition to end of frame.
ERROR sets the trigger condition to error.

TriggerABusBItemFlexrayCyclecount ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemFlexrayCyclecountHivalue

Return the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue command.

Description

This command specifies the high value when triggering on a FlexRay bus cycle count field. (Use TRIGGER:A:BUS:BX:FLEXRAY:CYCLECOUNT:VALUE to set the low value.) The trigger condition must be set to CYCLEcount (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue?

Info

<QString> is a quoted string that is the cycle count high value.

qualifier `property` ¶

qualifier: TriggerABusBItemFlexrayCyclecountQualifier

Return the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier command.

Description

This command specifies the qualifier (<, >, =, <=, >=, not =, in range, out of range) to use when triggering on the FlexRay bus cycle count field. The trigger condition must be set to CYCLEcount (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier?

Info

LESSthan sets the cycle count qualifier to less than.
MOREthan sets the cycle count qualifier to more than.
EQual sets the cycle count qualifier to equal.
UNEQual sets the cycle count qualifier to not equal.
LESSEQual sets the cycle count qualifier to less than or equal.
MOREEQual sets the cycle count qualifier to greater than or equal.
INrange sets the cycle count qualifier to in range.
OUTrange sets the cycle count qualifier to out of range.

value `property` ¶

value: TriggerABusBItemFlexrayCyclecountValue

Return the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue command.

Description

This command specifies the low value when triggering on the FlexRay bus cycle count field. (Use TRIGGER:A:BUS:BX:FLEXRAY:CYCLECOUNT:HIVALUE to set the upper value.) The trigger condition must be set to CYCLEcount (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue?

Info

<QString> is a quoted binary data string that represents the cycle count low value.

TriggerABusBItemFlexrayCyclecountHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue command.

Description

This command specifies the high value when triggering on a FlexRay bus cycle count field. (Use TRIGGER:A:BUS:BX:FLEXRAY:CYCLECOUNT:VALUE to set the low value.) The trigger condition must be set to CYCLEcount (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue?

Info

<QString> is a quoted string that is the cycle count high value.

TriggerABusBItemFlexrayCyclecountQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier command.

Description

This command specifies the qualifier (<, >, =, <=, >=, not =, in range, out of range) to use when triggering on the FlexRay bus cycle count field. The trigger condition must be set to CYCLEcount (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier?

Info

LESSthan sets the cycle count qualifier to less than.
MOREthan sets the cycle count qualifier to more than.
EQual sets the cycle count qualifier to equal.
UNEQual sets the cycle count qualifier to not equal.
LESSEQual sets the cycle count qualifier to less than or equal.
MOREEQual sets the cycle count qualifier to greater than or equal.
INrange sets the cycle count qualifier to in range.
OUTrange sets the cycle count qualifier to out of range.

TriggerABusBItemFlexrayCyclecountValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue command.

Description

This command specifies the low value when triggering on the FlexRay bus cycle count field. (Use TRIGGER:A:BUS:BX:FLEXRAY:CYCLECOUNT:HIVALUE to set the upper value.) The trigger condition must be set to CYCLEcount (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue?

Info

<QString> is a quoted binary data string that represents the cycle count low value.

TriggerABusBItemFlexrayData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet command.
.qualifier: The TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier command.
.size: The TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemFlexrayDataHivalue

Return the TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue command.

Description

This command specifies the high value when triggering on the FlexRay bus data field. (Use TRIGGER:A:BUS:BX:FLEXRAY:DATA:VALUE to set the lower value.) The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue?

Info

<QString> is a quoted string that is the binary data high value.

offset `property` ¶

offset: TriggerABusBItemFlexrayDataOffset

Return the TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet command.

Description

This command specifies the offset of the data string, in bytes, when triggering on the FlexRay bus data field. The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet?

Info

<NR1> is the offset of the data string in bytes. A byte offset of -1 signifies ‘don’t care’, and no byte offset is used. The instrument will trigger on or match any byte value that fits.

qualifier `property` ¶

qualifier: TriggerABusBItemFlexrayDataQualifier

Return the TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier command.

Description

This command specifies the qualifier (<, >, =, <=, >=, not =, in range, out of range) to use when triggering on the FlexRay bus data field. The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier?

Info

LESSthan sets the data qualifier to less than.
MOREthan sets the data qualifier to greater than.
EQual sets the data qualifier to eqaual.
UNEQual sets the data qualifier to not equal.
LESSEQual sets the data qualifier to less than or equal.
MOREEQual sets the data qualifier to greater than or equal.
INrange sets the data qualifier to in range.
OUTrange sets the data qualifier to out of range.

size `property` ¶

size: TriggerABusBItemFlexrayDataSize

Return the TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe command.

Description

This command specifies the length of the data string, in bytes, when triggering on the FlexRay bus data field. The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe?

Info

<NR1> is the FlexRay data string length, in bytes.

value `property` ¶

value: TriggerABusBItemFlexrayDataValue

Return the TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue command.

Description

This command specifies the low value when triggering on the FlexRay bus data field. (Use TRIGGER:A:BUS:BX:FLEXRAY:DATA:HIVALUE to set the upper value.) The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue?

Info

<QString> is a quoted string.

TriggerABusBItemFlexrayDataHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue command.

Description

This command specifies the high value when triggering on the FlexRay bus data field. (Use TRIGGER:A:BUS:BX:FLEXRAY:DATA:VALUE to set the lower value.) The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue?

Info

<QString> is a quoted string that is the binary data high value.

TriggerABusBItemFlexrayDataOffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet command.

Description

This command specifies the offset of the data string, in bytes, when triggering on the FlexRay bus data field. The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:OFFSet?

Info

<NR1> is the offset of the data string in bytes. A byte offset of -1 signifies ‘don’t care’, and no byte offset is used. The instrument will trigger on or match any byte value that fits.

TriggerABusBItemFlexrayDataQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier command.

Description

This command specifies the qualifier (<, >, =, <=, >=, not =, in range, out of range) to use when triggering on the FlexRay bus data field. The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:DATa:QUALifier?

Info

LESSthan sets the data qualifier to less than.
MOREthan sets the data qualifier to greater than.
EQual sets the data qualifier to eqaual.
UNEQual sets the data qualifier to not equal.
LESSEQual sets the data qualifier to less than or equal.
MOREEQual sets the data qualifier to greater than or equal.
INrange sets the data qualifier to in range.
OUTrange sets the data qualifier to out of range.

TriggerABusBItemFlexrayDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe command.

Description

This command specifies the length of the data string, in bytes, when triggering on the FlexRay bus data field. The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:SIZe?

Info

<NR1> is the FlexRay data string length, in bytes.

TriggerABusBItemFlexrayDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue command.

Description

This command specifies the low value when triggering on the FlexRay bus data field. (Use TRIGGER:A:BUS:BX:FLEXRAY:DATA:HIVALUE to set the upper value.) The trigger condition needs to be set to ID or IDANDDATA (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue?

Info

<QString> is a quoted string.

TriggerABusBItemFlexrayEoftype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE command.

Description

This command specifies the end of file type (static, dynamic or any) when triggering on the FlexRay bus EOF field. The trigger condition needs to be set to EOF (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE {STATic|DYNAMic|ANY}
- TRIGger:A:BUS:B<x>:FLEXray:EOFTYPE?

Info

STATic specifies triggering on the STATIC end of file type.
DYNAMic specifies triggering on the DYNAMIC end of file type.
ANY specifies triggering on a STATIC or DYNAMIC end of file type.

TriggerABusBItemFlexrayErrtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE command.

Description

This command specifies the error type when triggering on the FlexRay bus signal. The trigger condition needs to be set to ERROR (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE {CRCHeader|CRCTrailer|SYNCFrame|STARTupnosync|NULLFRStatic|NULLFRDynamic}
- TRIGger:A:BUS:B<x>:FLEXray:ERRTYPE?

Info

CRCHeader sets the error type to CRCHeader.
CRCTrailer sets the error type to CRCTrailer.
SYNCFrame sets the error type to SYNCFrame.
STARTupnosync sets the error type to STARTupnosync.
NULLFRStatic sets the error type to NULLFRStatic.
NULLFRDynamic sets the error type to NULLFRDynamic.

TriggerABusBItemFlexrayFrameid ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemFlexrayFrameidHivalue

Return the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue command.

Description

This command specifies the high value when triggering on the FlexRay bus frame ID field. (Use TRIGGER:A:BUS:BX:FLEXRAY:FRAMEID:VALUE to set the low value.) The trigger condition needs to be set to IDentifier (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue?

Info

<QString> is a quoted string that is the binary frame ID high value.

qualifier `property` ¶

qualifier: TriggerABusBItemFlexrayFrameidQualifier

Return the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier command.

Description

This command specifies the qualifier to use when triggering on the FlexRay bus frame ID field. The trigger condition needs to be set to IDentifier (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier?

Info

LESSthan sets the frame ID qualifier to less than.
MOREthan sets the frame ID qualifier to greater than.
EQual sets the frame ID qualifier to equal.
UNEQual sets the frame ID qualifier to not equal.
LESSEQual sets the frame ID qualifier to less than or equal.
MOREEQual sets the frame ID qualifier to greater than or equal.
INrange sets the frame ID qualifier to in range.
OUTrange sets the frame ID qualifier to out of range.

value `property` ¶

value: TriggerABusBItemFlexrayFrameidValue

Return the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue command.

Description

This command specifies the low value when triggering on the FlexRay bus frame ID field. (Use TRIGGER:A:BUS:BX:FLEXRAY:FRAMEID:HIVALUE to set the high value.) The trigger condition needs to be set to IDentifier (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue?

Info

<QString> is a quoted string that is the FlexRay frame ID low value.

TriggerABusBItemFlexrayFrameidHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue command.

Description

This command specifies the high value when triggering on the FlexRay bus frame ID field. (Use TRIGGER:A:BUS:BX:FLEXRAY:FRAMEID:VALUE to set the low value.) The trigger condition needs to be set to IDentifier (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:HIVALue?

Info

<QString> is a quoted string that is the binary frame ID high value.

TriggerABusBItemFlexrayFrameidQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier command.

Description

This command specifies the qualifier to use when triggering on the FlexRay bus frame ID field. The trigger condition needs to be set to IDentifier (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:QUALifier?

Info

LESSthan sets the frame ID qualifier to less than.
MOREthan sets the frame ID qualifier to greater than.
EQual sets the frame ID qualifier to equal.
UNEQual sets the frame ID qualifier to not equal.
LESSEQual sets the frame ID qualifier to less than or equal.
MOREEQual sets the frame ID qualifier to greater than or equal.
INrange sets the frame ID qualifier to in range.
OUTrange sets the frame ID qualifier to out of range.

TriggerABusBItemFlexrayFrameidValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue command.

Description

This command specifies the low value when triggering on the FlexRay bus frame ID field. (Use TRIGGER:A:BUS:BX:FLEXRAY:FRAMEID:HIVALUE to set the high value.) The trigger condition needs to be set to IDentifier (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue <QString>
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEID:VALue?

Info

<QString> is a quoted string that is the FlexRay frame ID low value.

TriggerABusBItemFlexrayFrametype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:FRAMEType command.

Description

This command specifies the frame type (normal, payload, null, sync or startup) when triggering on the FlexRay bus signal. The trigger condition needs to be set to FRAMEType (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:FRAMEType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:FRAMEType {NORMal|PAYLoad|NULL|SYNC|STARTup}
- TRIGger:A:BUS:B<x>:FLEXray:FRAMEType?

Info

NORMal specifies the normal frame type.
PAYLoad specifies the payload frame type.
NULL specifies the null frame type.
SYNC specifies the sync frame type.
STARTup specifies the startup frame type.

TriggerABusBItemFlexrayHeader ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:HEADER command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER? query and raise an AssertionError if the returned value does not match value.

Properties

.crc: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC command.
.cyclecount: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount command.
.frameid: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID command.
.indbits: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits command.
.paylength: The TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength command.

crc `property` ¶

crc: TriggerABusBItemFlexrayHeaderCrc

Return the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC command.

Description

This command specifies the CRC portion of the binary header string when triggering on the FlexRay bus signal. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC?

Info

<QString> is a quoted string that is the CRC portion of the binary header string.

cyclecount `property` ¶

cyclecount: TriggerABusBItemFlexrayHeaderCyclecount

Return the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount command.

Description

This command specifies the cycle count portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount?

Info

<QString> is a quoted string that is the cycle count portion of the binary header string.

frameid `property` ¶

frameid: TriggerABusBItemFlexrayHeaderFrameid

Return the TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID command.

Description

This command specifies the frame ID portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID?

Info

<QString> is a quoted string that represents the frame ID portion of the binary header string.

indbits `property` ¶

indbits: TriggerABusBItemFlexrayHeaderIndbits

Return the TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits command.

Description

This command specifies the indicator bits portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits?

Info

<QString> is a quoted string that is the indicator bits portion of the binary header string.

paylength `property` ¶

paylength: TriggerABusBItemFlexrayHeaderPaylength

Return the TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength command.

Description

This command specifies the payload length portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength?

Info

<QString> is the length of the payload portion of the Binary header string.

TriggerABusBItemFlexrayHeaderCrc ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC command.

Description

This command specifies the CRC portion of the binary header string when triggering on the FlexRay bus signal. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CRC?

Info

<QString> is a quoted string that is the CRC portion of the binary header string.

TriggerABusBItemFlexrayHeaderCyclecount ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount command.

Description

This command specifies the cycle count portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:CYCLEcount?

Info

<QString> is a quoted string that is the cycle count portion of the binary header string.

TriggerABusBItemFlexrayHeaderFrameid ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID command.

Description

This command specifies the frame ID portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:FRAMEID?

Info

<QString> is a quoted string that represents the frame ID portion of the binary header string.

TriggerABusBItemFlexrayHeaderIndbits ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits command.

Description

This command specifies the indicator bits portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:INDBits?

Info

<QString> is a quoted string that is the indicator bits portion of the binary header string.

TriggerABusBItemFlexrayHeaderPaylength ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength command.

Description

This command specifies the payload length portion of the binary header string when triggering on the FlexRay bus header. The trigger condition needs to be set to HEADer (using TRIGGER:A:BUS:BX:FLEXRAY:CONDITION). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength <QString>
- TRIGger:A:BUS:B<x>:FLEXray:HEADER:PAYLength?

Info

<QString> is the length of the payload portion of the Binary header string.

TriggerABusBItemI2c ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C? query and raise an AssertionError if the returned value does not match value.

Properties

.address: The TRIGger:A:BUS:B<x>:I2C:ADDRess command tree.
.condition: The TRIGger:A:BUS:B<x>:I2C:CONDition command.
.data: The TRIGger:A:BUS:B<x>:I2C:DATa command tree.

address `property` ¶

address: TriggerABusBItemI2cAddress

Return the TRIGger:A:BUS:B<x>:I2C:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.mode: The TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe command.
.type: The TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe command.
.value: The TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue command.

condition `property` ¶

condition: TriggerABusBItemI2cCondition

Return the TRIGger:A:BUS:B<x>:I2C:CONDition command.

Description

This command specifies the trigger condition for an I 2 C trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:CONDition {STARt|STOP|REPEATstart|ACKMISS|ADDRess|DATA|ADDRANDDATA}
- TRIGger:A:BUS:B<x>:I2C:CONDition?

Info

STARt specifies a search based on start condition.
STOP specifies a search based on stop condition.
REPEATstart specifies a search based on repeat of start condition.
ACKMISS specifies a search based on missing acknowledgement condition.
ADDRess specifies a search based on address.
DATA specifies a search based on data.
ADDRANDDATA specifies a search based on address and data.

data `property` ¶

data: TriggerABusBItemI2cData

Return the TRIGger:A:BUS:B<x>:I2C:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.direction: The TRIGger:A:BUS:B<x>:I2C:DATa:DIRection command.
.size: The TRIGger:A:BUS:B<x>:I2C:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:I2C:DATa:VALue command.

TriggerABusBItemI2cAddress ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess? query and raise an AssertionError if the returned value does not match value.

Properties

.mode: The TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe command.
.type: The TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe command.
.value: The TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue command.

mode `property` ¶

mode: TriggerABusBItemI2cAddressMode

Return the TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe command.

Description

This command specifies the I 2 C address mode to 7 or 10-bit. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe {ADDR7|ADDR10}
- TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe?

Info

ADDR7 specifies the 7-bit I2C address mode.
ADDR10 specifies the 10-bit I2C address mode.

type `property` ¶

type: TriggerABusBItemI2cAddressType

Return the TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe command.

Description

This command specifies the I 2 C address type. The only supported address type is USER. Applies to bus , where x

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe {GENeralcall|STARtbyte|HSmode|EEPROM|USER}
- TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe?

Info

GENeralcall specifies a general call address.
STARtbyte specifies a start byte address.
HSmode specifies a high-speed mode address.
EEPROM specifies an EEPROM address.
USER specifies a user address.

value `property` ¶

value: TriggerABusBItemI2cAddressValue

Return the TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue command.

Description

This command specifies the binary address string used for the I 2 C trigger if the trigger condition is ADDRESS or ADDRANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue?

Info

<QString> is up to 7 or 10-bits depending on the address mode that specifies the address. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemI2cAddressMode ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe command.

Description

This command specifies the I 2 C address mode to 7 or 10-bit. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe {ADDR7|ADDR10}
- TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe?

Info

ADDR7 specifies the 7-bit I2C address mode.
ADDR10 specifies the 10-bit I2C address mode.

TriggerABusBItemI2cAddressType ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe command.

Description

This command specifies the I 2 C address type. The only supported address type is USER. Applies to bus , where x

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe {GENeralcall|STARtbyte|HSmode|EEPROM|USER}
- TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe?

Info

GENeralcall specifies a general call address.
STARtbyte specifies a start byte address.
HSmode specifies a high-speed mode address.
EEPROM specifies an EEPROM address.
USER specifies a user address.

TriggerABusBItemI2cAddressValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue command.

Description

This command specifies the binary address string used for the I 2 C trigger if the trigger condition is ADDRESS or ADDRANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue?

Info

<QString> is up to 7 or 10-bits depending on the address mode that specifies the address. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemI2cCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:CONDition command.

Description

This command specifies the trigger condition for an I 2 C trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:CONDition {STARt|STOP|REPEATstart|ACKMISS|ADDRess|DATA|ADDRANDDATA}
- TRIGger:A:BUS:B<x>:I2C:CONDition?

Info

STARt specifies a search based on start condition.
STOP specifies a search based on stop condition.
REPEATstart specifies a search based on repeat of start condition.
ACKMISS specifies a search based on missing acknowledgement condition.
ADDRess specifies a search based on address.
DATA specifies a search based on data.
ADDRANDDATA specifies a search based on address and data.

TriggerABusBItemI2cData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.direction: The TRIGger:A:BUS:B<x>:I2C:DATa:DIRection command.
.size: The TRIGger:A:BUS:B<x>:I2C:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:I2C:DATa:VALue command.

direction `property` ¶

direction: TriggerABusBItemI2cDataDirection

Return the TRIGger:A:BUS:B<x>:I2C:DATa:DIRection command.

Description

This command specifies the I 2 C trigger type to be valid on a Read, Write, or Either condition. Read or write is indicated by the R/W bit in the I 2 C protocol. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa:DIRection? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:DIRection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:DIRection value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:DATa:DIRection {READ|WRITE|NOCARE}
- TRIGger:A:BUS:B<x>:I2C:DATa:DIRection?

Info

READ specifies read as the data direction.
WRITE specifies write as the data direction.
NOCARE specifies either as the data direction.

size `property` ¶

size: TriggerABusBItemI2cDataSize

Return the TRIGger:A:BUS:B<x>:I2C:DATa:SIZe command.

Description

This command specifies the length of the data string in bytes to be used for an I2C trigger if the trigger condition is DATA or ADDRANDDATA. Applies to bus , where the bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:I2C:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

value `property` ¶

value: TriggerABusBItemI2cDataValue

Return the TRIGger:A:BUS:B<x>:I2C:DATa:VALue command.

Description

This command specifies the binary data string used for I2C triggering if the trigger condition is DATA or ADDRANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:I2C:DATa:VALue?

Info

<QString> is the binary data string, where the number of bits is 8 times the number of bytes specified. The only allowed characters in the string are 0, 1, and X.

TriggerABusBItemI2cDataDirection ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:DATa:DIRection command.

Description

This command specifies the I 2 C trigger type to be valid on a Read, Write, or Either condition. Read or write is indicated by the R/W bit in the I 2 C protocol. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa:DIRection? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:DIRection? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:DIRection value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:DATa:DIRection {READ|WRITE|NOCARE}
- TRIGger:A:BUS:B<x>:I2C:DATa:DIRection?

Info

READ specifies read as the data direction.
WRITE specifies write as the data direction.
NOCARE specifies either as the data direction.

TriggerABusBItemI2cDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:DATa:SIZe command.

Description

This command specifies the length of the data string in bytes to be used for an I2C trigger if the trigger condition is DATA or ADDRANDDATA. Applies to bus , where the bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:I2C:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

TriggerABusBItemI2cDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:I2C:DATa:VALue command.

Description

This command specifies the binary data string used for I2C triggering if the trigger condition is DATA or ADDRANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:I2C:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:I2C:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:I2C:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:I2C:DATa:VALue?

Info

<QString> is the binary data string, where the number of bits is 8 times the number of bytes specified. The only allowed characters in the string are 0, 1, and X.

TriggerABusBItemLin ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:LIN:CONDition command.
.data: The TRIGger:A:BUS:B<x>:LIN:DATa command tree.
.errtype: The TRIGger:A:BUS:B<x>:LIN:ERRTYPE command.
.identifier: The TRIGger:A:BUS:B<x>:LIN:IDentifier command tree.

condition `property` ¶

condition: TriggerABusBItemLinCondition

Return the TRIGger:A:BUS:B<x>:LIN:CONDition command.

Description

This command specifies the trigger condition for LIN. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:CONDition {SYNCField|IDentifier|DATA|IDANDDATA|WAKEup|SLEEP|ERROR}
- TRIGger:A:BUS:B<x>:LIN:CONDition?

Info

SYNCField sets the LIN trigger condition to sync field.
IDentifier sets the LIN trigger condition to identifier.
DATA sets the LIN trigger condition to data.
IDANDDATA sets the LIN trigger condition to id and data.
WAKEup sets the LIN trigger condition to wake up.
SLEEP sets the LIN trigger condition to sleep.
ERROR sets the LIN trigger condition to error.

data `property` ¶

data: TriggerABusBItemLinData

Return the TRIGger:A:BUS:B<x>:LIN:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier command.
.size: The TRIGger:A:BUS:B<x>:LIN:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:LIN:DATa:VALue command.

errtype `property` ¶

errtype: TriggerABusBItemLinErrtype

Return the TRIGger:A:BUS:B<x>:LIN:ERRTYPE command.

Description

This command specifies the error type be used for LIN trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:ERRTYPE {SYNC|PARity|CHecksum|HEADertime|RESPtime|FRAMetime}
- TRIGger:A:BUS:B<x>:LIN:ERRTYPE?

Info

SYNC sets the LIN error type to SYNC.
PARity sets the LIN error type to parity.
CHecksum sets the LIN error type to checksum.
HEADertime sets the LIN error type to header time.
RESPtime sets the LIN error type to response time.
FRAMetime sets the LIN error type to frame time.

identifier `property` ¶

identifier: TriggerABusBItemLinIdentifier

Return the TRIGger:A:BUS:B<x>:LIN:IDentifier command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue command.

TriggerABusBItemLinCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:CONDition command.

Description

This command specifies the trigger condition for LIN. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:CONDition {SYNCField|IDentifier|DATA|IDANDDATA|WAKEup|SLEEP|ERROR}
- TRIGger:A:BUS:B<x>:LIN:CONDition?

Info

SYNCField sets the LIN trigger condition to sync field.
IDentifier sets the LIN trigger condition to identifier.
DATA sets the LIN trigger condition to data.
IDANDDATA sets the LIN trigger condition to id and data.
WAKEup sets the LIN trigger condition to wake up.
SLEEP sets the LIN trigger condition to sleep.
ERROR sets the LIN trigger condition to error.

TriggerABusBItemLinData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier command.
.size: The TRIGger:A:BUS:B<x>:LIN:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:LIN:DATa:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemLinDataHivalue

Return the TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue command.

Description

This command specifies the high data value string used for a LIN bus trigger when the trigger condition is DATA or IDANDDATA and the data qualifier is INRANGE or OUTRANGE. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue?

Info

<QString> is a quoted string that is the binary data string used for LIN trigger if the trigger condition is ID or IDANDDATA.

qualifier `property` ¶

qualifier: TriggerABusBItemLinDataQualifier

Return the TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier command.

Description

This command specifies the LIN data qualifier. This only applies if the trigger condition is IDANDDATA or DATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier?

Info

LESSthan sets the LIN data qualifier to less than.
MOREthan sets the LIN data qualifier to greater than.
EQual sets the LIN data qualifier to equal.
UNEQual sets the LIN data qualifier to not equal.
LESSEQual sets the LIN data qualifier to less than or equal.
MOREEQual sets the LIN data qualifier to greater than or equal.
INrange sets the LIN data qualifier to in range.
OUTrange sets the LIN data qualifier to out of range.

size `property` ¶

size: TriggerABusBItemLinDataSize

Return the TRIGger:A:BUS:B<x>:LIN:DATa:SIZe command.

Description

This command specifies the length of the data string in bytes to be used for LIN trigger. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:LIN:DATa:SIZe?

Info

<NR1> is the size of the data string in bytes.

value `property` ¶

value: TriggerABusBItemLinDataValue

Return the TRIGger:A:BUS:B<x>:LIN:DATa:VALue command.

Description

This command specifies the binary data string to be used for LIN trigger condition if trigger condition is ID or IDANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:LIN:DATa:VALue?

Info

<QString> is a quoted string that is the LIN trigger data value.

TriggerABusBItemLinDataHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue command.

Description

This command specifies the high data value string used for a LIN bus trigger when the trigger condition is DATA or IDANDDATA and the data qualifier is INRANGE or OUTRANGE. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:LIN:DATa:HIVALue?

Info

<QString> is a quoted string that is the binary data string used for LIN trigger if the trigger condition is ID or IDANDDATA.

TriggerABusBItemLinDataQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier command.

Description

This command specifies the LIN data qualifier. This only applies if the trigger condition is IDANDDATA or DATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:LIN:DATa:QUALifier?

Info

LESSthan sets the LIN data qualifier to less than.
MOREthan sets the LIN data qualifier to greater than.
EQual sets the LIN data qualifier to equal.
UNEQual sets the LIN data qualifier to not equal.
LESSEQual sets the LIN data qualifier to less than or equal.
MOREEQual sets the LIN data qualifier to greater than or equal.
INrange sets the LIN data qualifier to in range.
OUTrange sets the LIN data qualifier to out of range.

TriggerABusBItemLinDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:DATa:SIZe command.

Description

This command specifies the length of the data string in bytes to be used for LIN trigger. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:LIN:DATa:SIZe?

Info

<NR1> is the size of the data string in bytes.

TriggerABusBItemLinDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:DATa:VALue command.

Description

This command specifies the binary data string to be used for LIN trigger condition if trigger condition is ID or IDANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:LIN:DATa:VALue?

Info

<QString> is a quoted string that is the LIN trigger data value.

TriggerABusBItemLinErrtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:ERRTYPE command.

Description

This command specifies the error type be used for LIN trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:ERRTYPE {SYNC|PARity|CHecksum|HEADertime|RESPtime|FRAMetime}
- TRIGger:A:BUS:B<x>:LIN:ERRTYPE?

Info

SYNC sets the LIN error type to SYNC.
PARity sets the LIN error type to parity.
CHecksum sets the LIN error type to checksum.
HEADertime sets the LIN error type to header time.
RESPtime sets the LIN error type to response time.
FRAMetime sets the LIN error type to frame time.

TriggerABusBItemLinIdentifier ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:IDentifier command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue command.

value `property` ¶

value: TriggerABusBItemLinIdentifierValue

Return the TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue command.

Description

This command specifies the binary address string used for LIN bus trigger if the trigger condition is ID or IDANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue <QString>
- TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue?

Info

<QString> is the binary address string used for LIN trigger if the trigger condition is ID or IDANDDATA.

TriggerABusBItemLinIdentifierValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue command.

Description

This command specifies the binary address string used for LIN bus trigger if the trigger condition is ID or IDANDDATA. The bus number is specified by x.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue <QString>
- TRIGger:A:BUS:B<x>:LIN:IDentifier:VALue?

Info

<QString> is the binary address string used for LIN trigger if the trigger condition is ID or IDANDDATA.

TriggerABusBItemMil1553b ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B? query and raise an AssertionError if the returned value does not match value.

Properties

.command: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND command tree.
.condition: The TRIGger:A:BUS:B<x>:MIL1553B:CONDition command.
.data: The TRIGger:A:BUS:B<x>:MIL1553B:DATa command tree.
.errtype: The TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE command.
.status: The TRIGger:A:BUS:B<x>:MIL1553B:STATus command tree.
.time: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe command tree.

command `property` ¶

command: TriggerABusBItemMil1553bCommand

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.address: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess command tree.
.count: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt command.
.parity: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity command.
.subaddress: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress command.
.trbit: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit command.

condition `property` ¶

condition: TriggerABusBItemMil1553bCondition

Return the TRIGger:A:BUS:B<x>:MIL1553B:CONDition command.

Description

This command specifies a word type or condition within a MIL-STD-1553 bus word to trigger on. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:CONDition {SYNC|COMMAND|STATus|DATA|TIMe|ERRor}
- TRIGger:A:BUS:B<x>:MIL1553B:CONDition?

Info

SYNC refers to the 3-bit sync pulse that precedes each word.
COMMAND is one of 3 16-bit word types. It specifies the function that a remote terminal is to perform.
STATus is one of 3 16-bit word types. Remote terminals respond to valid message transmissions via status words.
DATA is one of 3 16-bit word types.
TIMe specifies to trigger on either the RT (remote terminal response time), or the IMG (Inter-message Gap). Use the commands TRIGGER:A:BUS:BX:MIL1553B:TIME:QUALIFIER, TRIGGER:A:BUS:BX:MIL1553B:TIME:LESSLIMIT, and TRIGGER:A:BUS:BX:MIL1553B:TIME:MORELIMIT to specify the time parameters.
ERRor specifies to trigger upon a signaling error. (You can specify which type of error - Parity, Sync, Manchester or Non-contiguous Data - by using the TRIGGER:A:BUS:BX:MIL1553B:ERRTYPE command.).

data `property` ¶

data: TriggerABusBItemMil1553bData

Return the TRIGger:A:BUS:B<x>:MIL1553B:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.parity: The TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity command.
.value: The TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue command.

errtype `property` ¶

errtype: TriggerABusBItemMil1553bErrtype

Return the TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE command.

Description

When the MIL-STD-1553 bus trigger condition is set to ERRor, this command specifies the signaling error type to be used in the trigger: Parity, Sync, Manchester or Data. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE {PARity|SYNC|MANCHester|DATA}
- TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE?

status `property` ¶

status: TriggerABusBItemMil1553bStatus

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.address: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess command tree.
.bit: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT command tree.
.parity: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity command.

time `property` ¶

time: TriggerABusBItemMil1553bTime

Return the TRIGger:A:BUS:B<x>:MIL1553B:TIMe command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.lesslimit: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit command.
.morelimit: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit command.
.qualifier: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier command.

TriggerABusBItemMil1553bCommand ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND? query and raise an AssertionError if the returned value does not match value.

Properties

.address: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess command tree.
.count: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt command.
.parity: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity command.
.subaddress: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress command.
.trbit: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit command.

address `property` ¶

address: TriggerABusBItemMil1553bCommandAddress

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue command.

count `property` ¶

count: TriggerABusBItemMil1553bCommandCount

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the bit pattern for the 5-bit Word Count/Mode Code sub-address field that is to be used in the trigger. (Use the command TRIGGER:A:BUS:BX:MIL1553B:COMMAND:SUBADDRESS to specify Word Count or Mode Code.) In Word Count mode, this field defines the number of data words that is to be transmitted, or received, depending on the T/R bit setting. (Use the command TRIGGER:A:BUS:BX:MIL1553B:COMMAND:TRBIT to set the T/R bit.) A word count value of 0 actually indicates a transfer of 32 data words. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt?

Info

QString is a quoted string of up to 5 characters, where the allowable characters are 0, 1 and X. The bits specified in the quoted string replace the least significant bits, leaving any unspecified upper bits unchanged.

parity `property` ¶

parity: TriggerABusBItemMil1553bCommandParity

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the Command word parity that is to be used in the trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

subaddress `property` ¶

subaddress: TriggerABusBItemMil1553bCommandSubaddress

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the 5 bit sub-address that is to be used in the trigger. When the sub-address value is set to 00000 or 11111 binary, it specifies that the command is a ‘Mode Code’ command. Any other value specifies that it is a ‘Word Count’ command. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress?

trbit `property` ¶

trbit: TriggerABusBItemMil1553bCommandTrbit

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies that the transmit/receive bit (bit 9) is to be used in the trigger. The transmit/receive bit defines the direction of information flow, and is always from the point of view of the remote terminal. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit {RX|TX|X}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit?

Info

RX (logic 0) directs the instrument to trigger on a TX or ‘transmit’ from a remote terminal .
TX (logic 1) directs the instrument to trigger on an RX or ‘receive’ from a remote terminal.
X indicates ‘don’t care’.

TriggerABusBItemMil1553bCommandAddress ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemMil1553bCommandAddressHivalue

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, and the qualifier is set to INrange or OUTrange, this command specifies the upper limit of the range for the remote terminal address field. (Use the command TRIGGER:A:BUS:BX:MIL1553B:COMMAND:ADDRESS:VALUE to specify the lower limit of the range.) The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue?

qualifier `property` ¶

qualifier: TriggerABusBItemMil1553bCommandAddressQualifier

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the qualifier to be used with the remote terminal address field. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier?

Info

LESSthan sets the Command Address qualifier to less than.
MOREthan sets the Command Address qualifier to greater than.
EQual sets the Command Address qualifier to equal.
UNEQual sets the Command Address qualifier to not equal.
LESSEQual sets the Command Address qualifier to less than or equal.
MOREEQual sets the Command Address qualifier to greater than or equal.
INrange sets the Command Address qualifier to in range.
OUTrange sets the Command Address qualifier to out of range.

value `property` ¶

value: TriggerABusBItemMil1553bCommandAddressValue

Return the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the value of the 5-bit remote terminal address to be used in the trigger. When the MIL-STD-1553 bus trigger condition is set to COMMAND, and the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the remote terminal address range. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue?

TriggerABusBItemMil1553bCommandAddressHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, and the qualifier is set to INrange or OUTrange, this command specifies the upper limit of the range for the remote terminal address field. (Use the command TRIGGER:A:BUS:BX:MIL1553B:COMMAND:ADDRESS:VALUE to specify the lower limit of the range.) The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:HIVALue?

TriggerABusBItemMil1553bCommandAddressQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the qualifier to be used with the remote terminal address field. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:QUALifier?

Info

LESSthan sets the Command Address qualifier to less than.
MOREthan sets the Command Address qualifier to greater than.
EQual sets the Command Address qualifier to equal.
UNEQual sets the Command Address qualifier to not equal.
LESSEQual sets the Command Address qualifier to less than or equal.
MOREEQual sets the Command Address qualifier to greater than or equal.
INrange sets the Command Address qualifier to in range.
OUTrange sets the Command Address qualifier to out of range.

TriggerABusBItemMil1553bCommandAddressValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the value of the 5-bit remote terminal address to be used in the trigger. When the MIL-STD-1553 bus trigger condition is set to COMMAND, and the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the remote terminal address range. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:ADDRess:VALue?

TriggerABusBItemMil1553bCommandCount ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the bit pattern for the 5-bit Word Count/Mode Code sub-address field that is to be used in the trigger. (Use the command TRIGGER:A:BUS:BX:MIL1553B:COMMAND:SUBADDRESS to specify Word Count or Mode Code.) In Word Count mode, this field defines the number of data words that is to be transmitted, or received, depending on the T/R bit setting. (Use the command TRIGGER:A:BUS:BX:MIL1553B:COMMAND:TRBIT to set the T/R bit.) A word count value of 0 actually indicates a transfer of 32 data words. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:COUNt?

Info

QString is a quoted string of up to 5 characters, where the allowable characters are 0, 1 and X. The bits specified in the quoted string replace the least significant bits, leaving any unspecified upper bits unchanged.

TriggerABusBItemMil1553bCommandParity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the Command word parity that is to be used in the trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:PARity?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bCommandSubaddress ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies the 5 bit sub-address that is to be used in the trigger. When the sub-address value is set to 00000 or 11111 binary, it specifies that the command is a ‘Mode Code’ command. Any other value specifies that it is a ‘Word Count’ command. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:SUBADdress?

TriggerABusBItemMil1553bCommandTrbit ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit command.

Description

When the MIL-STD-1553 bus trigger condition is set to COMMAND, this command specifies that the transmit/receive bit (bit 9) is to be used in the trigger. The transmit/receive bit defines the direction of information flow, and is always from the point of view of the remote terminal. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit {RX|TX|X}
- TRIGger:A:BUS:B<x>:MIL1553B:COMMAND:TRBit?

Info

RX (logic 0) directs the instrument to trigger on a TX or ‘transmit’ from a remote terminal .
TX (logic 1) directs the instrument to trigger on an RX or ‘receive’ from a remote terminal.
X indicates ‘don’t care’.

TriggerABusBItemMil1553bCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:CONDition command.

Description

This command specifies a word type or condition within a MIL-STD-1553 bus word to trigger on. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:CONDition {SYNC|COMMAND|STATus|DATA|TIMe|ERRor}
- TRIGger:A:BUS:B<x>:MIL1553B:CONDition?

Info

SYNC refers to the 3-bit sync pulse that precedes each word.
COMMAND is one of 3 16-bit word types. It specifies the function that a remote terminal is to perform.
STATus is one of 3 16-bit word types. Remote terminals respond to valid message transmissions via status words.
DATA is one of 3 16-bit word types.
TIMe specifies to trigger on either the RT (remote terminal response time), or the IMG (Inter-message Gap). Use the commands TRIGGER:A:BUS:BX:MIL1553B:TIME:QUALIFIER, TRIGGER:A:BUS:BX:MIL1553B:TIME:LESSLIMIT, and TRIGGER:A:BUS:BX:MIL1553B:TIME:MORELIMIT to specify the time parameters.
ERRor specifies to trigger upon a signaling error. (You can specify which type of error - Parity, Sync, Manchester or Non-contiguous Data - by using the TRIGGER:A:BUS:BX:MIL1553B:ERRTYPE command.).

TriggerABusBItemMil1553bData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.parity: The TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity command.
.value: The TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue command.

parity `property` ¶

parity: TriggerABusBItemMil1553bDataParity

Return the TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity command.

Description

When the MIL-STD-1553 bus trigger condition is set to DATa, this command specifies the data parity bit to be used in the trigger. Returned values are 0, 1, or X (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

value `property` ¶

value: TriggerABusBItemMil1553bDataValue

Return the TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to DATa, this command specifies the data binary pattern to be used in the trigger. This is a 16-bit field. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue?

TriggerABusBItemMil1553bDataParity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity command.

Description

When the MIL-STD-1553 bus trigger condition is set to DATa, this command specifies the data parity bit to be used in the trigger. Returned values are 0, 1, or X (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:PARity?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to DATa, this command specifies the data binary pattern to be used in the trigger. This is a 16-bit field. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:DATa:VALue?

TriggerABusBItemMil1553bErrtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE command.

Description

When the MIL-STD-1553 bus trigger condition is set to ERRor, this command specifies the signaling error type to be used in the trigger: Parity, Sync, Manchester or Data. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE {PARity|SYNC|MANCHester|DATA}
- TRIGger:A:BUS:B<x>:MIL1553B:ERRTYPE?

TriggerABusBItemMil1553bStatus ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus? query and raise an AssertionError if the returned value does not match value.

Properties

.address: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess command tree.
.bit: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT command tree.
.parity: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity command.

address `property` ¶

address: TriggerABusBItemMil1553bStatusAddress

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue command.

bit `property` ¶

bit: TriggerABusBItemMil1553bStatusBit

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.bcr: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR command.
.busy: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY command.
.dbca: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA command.
.instr: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR command.
.me: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME command.
.srq: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ command.
.subsf: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF command.
.tf: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF command.

parity `property` ¶

parity: TriggerABusBItemMil1553bStatusParity

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status parity bit value to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusAddress ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue command.
.qualifier: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier command.
.value: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemMil1553bStatusAddressHivalue

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, and the qualifier is set to INrange or OUTrange, this command specifies the upper limit for the 5 bit remote terminal address field of the Status word. (Use the command TRIGGER:A:BUS:BX:MIL1553B:STATUS:ADDRESS:VALUE to specify the lower limit.) The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue?

qualifier `property` ¶

qualifier: TriggerABusBItemMil1553bStatusAddressQualifier

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the qualifier to be used with the address field. The default is EQUAL. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier?

Info

LESSthan sets the Status Address qualifier to less than.
MOREthan sets the Status Address qualifier to greater than.
EQual sets the Status Address qualifier to equal.
UNEQual sets the Status Address qualifier to not equal.
LESSEQual sets the Status Address qualifier to less than or equal.
MOREEQual sets the Status Address qualifier to greater than or equal.
INrange sets the Status Address qualifier to in range.
OUTrange sets the Status Address qualifier to out of range.

value `property` ¶

value: TriggerABusBItemMil1553bStatusAddressValue

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the value of the 5-bit remote terminal address to be used in the trigger. When the MIL-STD-1553 bus trigger condition is set to STATus, and the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command TRIGGER:A:BUS:BX:MIL1553B:STATUS:ADDRESS:HIVALUE to specify the upper limit of the range.) The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue?

TriggerABusBItemMil1553bStatusAddressHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, and the qualifier is set to INrange or OUTrange, this command specifies the upper limit for the 5 bit remote terminal address field of the Status word. (Use the command TRIGGER:A:BUS:BX:MIL1553B:STATUS:ADDRESS:VALUE to specify the lower limit.) The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:HIVALue?

TriggerABusBItemMil1553bStatusAddressQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the qualifier to be used with the address field. The default is EQUAL. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:QUALifier?

Info

LESSthan sets the Status Address qualifier to less than.
MOREthan sets the Status Address qualifier to greater than.
EQual sets the Status Address qualifier to equal.
UNEQual sets the Status Address qualifier to not equal.
LESSEQual sets the Status Address qualifier to less than or equal.
MOREEQual sets the Status Address qualifier to greater than or equal.
INrange sets the Status Address qualifier to in range.
OUTrange sets the Status Address qualifier to out of range.

TriggerABusBItemMil1553bStatusAddressValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, and the qualifier is set to LESSthan, MOREthan, EQual, UNEQual, LESSEQual or MOREEQual, this command specifies the value of the 5-bit remote terminal address to be used in the trigger. When the MIL-STD-1553 bus trigger condition is set to STATus, and the qualifier is set to INrange or OUTrange, this command specifies the lower limit of the range. (Use the command TRIGGER:A:BUS:BX:MIL1553B:STATUS:ADDRESS:HIVALUE to specify the upper limit of the range.) The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue <QString>
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:ADDRess:VALue?

TriggerABusBItemMil1553bStatusBit ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT? query and raise an AssertionError if the returned value does not match value.

Properties

.bcr: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR command.
.busy: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY command.
.dbca: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA command.
.instr: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR command.
.me: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME command.
.srq: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ command.
.subsf: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF command.
.tf: The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF command.

bcr `property` ¶

bcr: TriggerABusBItemMil1553bStatusBitBcr

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word broadcast command received (BCR) bit value (bit 15) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

busy `property` ¶

busy: TriggerABusBItemMil1553bStatusBitBusy

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word busy bit value (bit 16) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

dbca `property` ¶

dbca: TriggerABusBItemMil1553bStatusBitDbca

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word dynamic bus control acceptance (DBCA) bit value (bit 18) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

instr `property` ¶

instr: TriggerABusBItemMil1553bStatusBitInstr

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word instrumentation bit value (bit 10) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

me `property` ¶

me: TriggerABusBItemMil1553bStatusBitMe

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word message error bit value (bit 9) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

srq `property` ¶

srq: TriggerABusBItemMil1553bStatusBitSrq

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word service request (SRQ) bit value (bit 11) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

subsf `property` ¶

subsf: TriggerABusBItemMil1553bStatusBitSubsf

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word subsystem flag bit value (bit 17) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

tf `property` ¶

tf: TriggerABusBItemMil1553bStatusBitTf

Return the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word terminal flag bit value (bit 19) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitBcr ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word broadcast command received (BCR) bit value (bit 15) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BCR?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitBusy ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word busy bit value (bit 16) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:BUSY?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitDbca ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word dynamic bus control acceptance (DBCA) bit value (bit 18) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:DBCA?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitInstr ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word instrumentation bit value (bit 10) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:INSTR?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitMe ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word message error bit value (bit 9) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:ME?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitSrq ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word service request (SRQ) bit value (bit 11) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SRQ?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitSubsf ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word subsystem flag bit value (bit 17) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:SUBSF?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusBitTf ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status word terminal flag bit value (bit 19) to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:BIT:TF?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bStatusParity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity command.

Description

When the MIL-STD-1553 bus trigger condition is set to STATus, this command specifies the status parity bit value to be used in the trigger. Returned values are 0, 1, or X (don’t care, which is the default). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity {0|1|X|ZERo|ONE|NOCARE|OFF|ON}
- TRIGger:A:BUS:B<x>:MIL1553B:STATus:PARity?

Info

0
1
X sets the value to X (‘don’t care’) which is the default.
ZERO sets the value to 0.
ONE sets the value to 1.
NOCARE sets the value to X (‘don’t care’) which is the default.
OFF sets the value to 0.
ON sets the value to 1.

TriggerABusBItemMil1553bTime ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:TIMe command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe? query and raise an AssertionError if the returned value does not match value.

Properties

.lesslimit: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit command.
.morelimit: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit command.
.qualifier: The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier command.

lesslimit `property` ¶

lesslimit: TriggerABusBItemMil1553bTimeLesslimit

Return the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit command.

Description

When the MIL-STD-1553 bus trigger condition is set to TIMe, this command specifies either the minimum remote terminal response time (RT) limit for the amount of time the terminal has to transmit, or it specifies the minimum inter-message gap (IMG). (You can specify RT or IMG using the TRIGGER:A:BUS:BX:MIL1553B:CONDITION TIMe command.) B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit <NR3>
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit?

Info

<NR3> is a floating point number that specifies either the minimum remote terminal response time (RT) or the inter-message gap (IMG) in seconds.

morelimit `property` ¶

morelimit: TriggerABusBItemMil1553bTimeMorelimit

Return the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit command.

Description

When the MIL-STD-1553 bus trigger condition is set to TIMe, this command specifies either the maximum remote terminal response time (RT) limit for the amount of time the terminal has to transmit, or it specifies the maximum inter-message gap (IMG). (You can specify the RT and IMG using the TRIGGER:A:BUS:BX:MIL1553B:CONDITION TIMe command.)

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit <NR3>
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit?

Info

<NR3> is a floating point number that specifies either the maximum remote terminal response time (RT) or the inter-message gap (IMG) in seconds.

qualifier `property` ¶

qualifier: TriggerABusBItemMil1553bTimeQualifier

Return the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier command.

Description

When the MIL-STD-1553 bus trigger condition is set to TIMe, this command specifies the trigger data time qualifier. (This includes a smaller set of arguments than other qualifier commands.) B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier {LESSthan|MOREthan|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier?

Info

LESSthan sets the Time qualifier to less than minimum.
MOREthan sets the Time qualifier to greater than maximum.
INrange sets the Time qualifier to inside range.
OUTrange sets the Time qualifier to out of range.

TriggerABusBItemMil1553bTimeLesslimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit command.

Description

When the MIL-STD-1553 bus trigger condition is set to TIMe, this command specifies either the minimum remote terminal response time (RT) limit for the amount of time the terminal has to transmit, or it specifies the minimum inter-message gap (IMG). (You can specify RT or IMG using the TRIGGER:A:BUS:BX:MIL1553B:CONDITION TIMe command.) B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit <NR3>
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit?

Info

<NR3> is a floating point number that specifies either the minimum remote terminal response time (RT) or the inter-message gap (IMG) in seconds.

TriggerABusBItemMil1553bTimeMorelimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit command.

Description

When the MIL-STD-1553 bus trigger condition is set to TIMe, this command specifies either the maximum remote terminal response time (RT) limit for the amount of time the terminal has to transmit, or it specifies the maximum inter-message gap (IMG). (You can specify the RT and IMG using the TRIGGER:A:BUS:BX:MIL1553B:CONDITION TIMe command.)

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit <NR3>
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit?

Info

<NR3> is a floating point number that specifies either the maximum remote terminal response time (RT) or the inter-message gap (IMG) in seconds.

TriggerABusBItemMil1553bTimeQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier command.

Description

When the MIL-STD-1553 bus trigger condition is set to TIMe, this command specifies the trigger data time qualifier. (This includes a smaller set of arguments than other qualifier commands.) B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier {LESSthan|MOREthan|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier?

Info

LESSthan sets the Time qualifier to less than minimum.
MOREthan sets the Time qualifier to greater than maximum.
INrange sets the Time qualifier to inside range.
OUTrange sets the Time qualifier to out of range.

TriggerABusBItemParallel ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:PARallel command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:PARallel? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:PARallel? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:PARallel:VALue command.

value `property` ¶

value: TriggerABusBItemParallelValue

Return the TRIGger:A:BUS:B<x>:PARallel:VALue command.

Description

This command specifies the binary data string to be used for a Parallel trigger. Applies to bus , where x

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:PARallel:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:PARallel:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:PARallel:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:PARallel:VALue <QString>
- TRIGger:A:BUS:B<x>:PARallel:VALue?

Info

<QString> is the binary data string.

TriggerABusBItemParallelValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:PARallel:VALue command.

Description

This command specifies the binary data string to be used for a Parallel trigger. Applies to bus , where x

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:PARallel:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:PARallel:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:PARallel:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:PARallel:VALue <QString>
- TRIGger:A:BUS:B<x>:PARallel:VALue?

Info

<QString> is the binary data string.

TriggerABusBItemRs232c ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:RS232C:CONDition command.
.rx: The TRIGger:A:BUS:B<x>:RS232C:RX command tree.
.tx: The TRIGger:A:BUS:B<x>:RS232C:TX command tree.

condition `property` ¶

condition: TriggerABusBItemRs232cCondition

Return the TRIGger:A:BUS:B<x>:RS232C:CONDition command.

Description

This command specifies the condition for an RS-232C trigger, where x B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:RS232C:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:CONDition {RXSTArt|RXDATA|RXENDPacket|TXSTArt|TXDATA|TXENDPacket}
- TRIGger:A:BUS:B<x>:RS232C:CONDition?

Info

RXSTArt specifies a search based on the RX Start Bit.
RXDATA specifies a search based on RX Data.
RXENDPacket specifies a search based on the RX End of Packet condition.
TXSTArt specifies a search base on the TX Start Bit.
TXDATA specifies a search based on TX Data.
TXENDPacket specifies a search based on the TX End of Packet condition.

rx `property` ¶

rx: TriggerABusBItemRs232cRx

Return the TRIGger:A:BUS:B<x>:RS232C:RX command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.data: The TRIGger:A:BUS:B<x>:RS232C:RX:DATa command tree.

tx `property` ¶

tx: TriggerABusBItemRs232cTx

Return the TRIGger:A:BUS:B<x>:RS232C:TX command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.data: The TRIGger:A:BUS:B<x>:RS232C:TX:DATa command tree.

TriggerABusBItemRs232cCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:CONDition command.

Description

This command specifies the condition for an RS-232C trigger, where x B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:RS232C:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:CONDition {RXSTArt|RXDATA|RXENDPacket|TXSTArt|TXDATA|TXENDPacket}
- TRIGger:A:BUS:B<x>:RS232C:CONDition?

Info

RXSTArt specifies a search based on the RX Start Bit.
RXDATA specifies a search based on RX Data.
RXENDPacket specifies a search based on the RX End of Packet condition.
TXSTArt specifies a search base on the TX Start Bit.
TXDATA specifies a search based on TX Data.
TXENDPacket specifies a search based on the TX End of Packet condition.

TriggerABusBItemRs232cRx ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:RX command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX? query and raise an AssertionError if the returned value does not match value.

Properties

.data: The TRIGger:A:BUS:B<x>:RS232C:RX:DATa command tree.

data `property` ¶

data: TriggerABusBItemRs232cRxData

Return the TRIGger:A:BUS:B<x>:RS232C:RX:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.size: The TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue command.

TriggerABusBItemRs232cRxData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:RX:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.size: The TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue command.

size `property` ¶

size: TriggerABusBItemRs232cRxDataSize

Return the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe command.

Description

This command specifies the length of the data string in Bytes for an RS-232 Trigger if the trigger condition is RXDATA. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

value `property` ¶

value: TriggerABusBItemRs232cRxDataValue

Return the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue command.

Description

This command specifies the binary data string for an RS-232 trigger if the trigger condition involves RX. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue?

Info

<Qstring> is the binary data string to be used for the trigger.

TriggerABusBItemRs232cRxDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe command.

Description

This command specifies the length of the data string in Bytes for an RS-232 Trigger if the trigger condition is RXDATA. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

TriggerABusBItemRs232cRxDataValue ¶

Bases: SCPICmdWriteNoArguments, SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue command.

Description

This command specifies the binary data string for an RS-232 trigger if the trigger condition involves RX. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write() method will send the TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue
- TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue?

Info

<Qstring> is the binary data string to be used for the trigger.

TriggerABusBItemRs232cTx ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:TX command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX? query and raise an AssertionError if the returned value does not match value.

Properties

.data: The TRIGger:A:BUS:B<x>:RS232C:TX:DATa command tree.

data `property` ¶

data: TriggerABusBItemRs232cTxData

Return the TRIGger:A:BUS:B<x>:RS232C:TX:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.size: The TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue command.

TriggerABusBItemRs232cTxData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:TX:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.size: The TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe command.
.value: The TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue command.

size `property` ¶

size: TriggerABusBItemRs232cTxDataSize

Return the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe command.

Description

This command specifies the length of the data string for an RS-232 trigger if the trigger condition is TXDATA. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe?

Info

<NR1> is the length of the data string in Bytes.

value `property` ¶

value: TriggerABusBItemRs232cTxDataValue

Return the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue command.

Description

This command specifies the binary data string for an RS-232 trigger if the condition involves TX. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue?

Info

<Qstring> is the binary data string to be used for the trigger.

TriggerABusBItemRs232cTxDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe command.

Description

This command specifies the length of the data string for an RS-232 trigger if the trigger condition is TXDATA. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe?

Info

<NR1> is the length of the data string in Bytes.

TriggerABusBItemRs232cTxDataValue ¶

Bases: SCPICmdWriteNoArguments, SCPICmdRead

The TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue command.

Description

This command specifies the binary data string for an RS-232 trigger if the condition involves TX. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write() method will send the TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue
- TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue?

Info

<Qstring> is the binary data string to be used for the trigger.

TriggerABusBItemSpi ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI? query and raise an AssertionError if the returned value does not match value.

Properties

.condition: The TRIGger:A:BUS:B<x>:SPI:CONDition command.
.data: The TRIGger:A:BUS:B<x>:SPI:DATa command tree.

condition `property` ¶

condition: TriggerABusBItemSpiCondition

Return the TRIGger:A:BUS:B<x>:SPI:CONDition command.

Description

This command specifies the trigger condition for a SPI trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:CONDition {SS|STARTofframe|MISO|MOSI|MISOMOSI}
- TRIGger:A:BUS:B<x>:SPI:CONDition?

Info

SS specifies the Slave Selection condition.
STARTofframe is applicable when BUS:B<x>:SPI:FRAMING is set to IDLEtime. When the trigger condition is set to STARTofframe, the instrument triggers on the first SPI clock after an idle time when there are no clocks.
MISO specifies the Master-In Slave-Out condition.
MOSI specifies the Master-Out Slave-In condition.
MISOMOSI specifies the Master-In Slave-Out and Master-Out Slave-In conditions.

data `property` ¶

data: TriggerABusBItemSpiData

Return the TRIGger:A:BUS:B<x>:SPI:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.size: The TRIGger:A:BUS:B<x>:SPI:DATa:SIZe command.
.in: The TRIGger:A:BUS:B<x>:SPI:DATa:IN command tree.
.miso: The TRIGger:A:BUS:B<x>:SPI:DATa:MISO command tree.
.out: The TRIGger:A:BUS:B<x>:SPI:DATa:OUT command tree.
.mosi: The TRIGger:A:BUS:B<x>:SPI:DATa:MOSI command tree.

TriggerABusBItemSpiCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:CONDition command.

Description

This command specifies the trigger condition for a SPI trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:CONDition {SS|STARTofframe|MISO|MOSI|MISOMOSI}
- TRIGger:A:BUS:B<x>:SPI:CONDition?

Info

SS specifies the Slave Selection condition.
STARTofframe is applicable when BUS:B<x>:SPI:FRAMING is set to IDLEtime. When the trigger condition is set to STARTofframe, the instrument triggers on the first SPI clock after an idle time when there are no clocks.
MISO specifies the Master-In Slave-Out condition.
MOSI specifies the Master-Out Slave-In condition.
MISOMOSI specifies the Master-In Slave-Out and Master-Out Slave-In conditions.

TriggerABusBItemSpiData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.size: The TRIGger:A:BUS:B<x>:SPI:DATa:SIZe command.
.in: The TRIGger:A:BUS:B<x>:SPI:DATa:IN command tree.
.miso: The TRIGger:A:BUS:B<x>:SPI:DATa:MISO command tree.
.out: The TRIGger:A:BUS:B<x>:SPI:DATa:OUT command tree.
.mosi: The TRIGger:A:BUS:B<x>:SPI:DATa:MOSI command tree.

in_ `property` ¶

in_: TriggerABusBItemSpiDataIn

Return the TRIGger:A:BUS:B<x>:SPI:DATa:IN command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue command.

miso `property` ¶

miso: TriggerABusBItemSpiDataMiso

Return the TRIGger:A:BUS:B<x>:SPI:DATa:MISO command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue command.

mosi `property` ¶

mosi: TriggerABusBItemSpiDataMosi

Return the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue command.

out `property` ¶

out: TriggerABusBItemSpiDataOut

Return the TRIGger:A:BUS:B<x>:SPI:DATa:OUT command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue command.

size `property` ¶

size: TriggerABusBItemSpiDataSize

Return the TRIGger:A:BUS:B<x>:SPI:DATa:SIZe command.

Description

This command specifies the length of the data string to be used for a SPI trigger if the trigger condition is DATa. B is the specified bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:SPI:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

TriggerABusBItemSpiDataIn ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:IN command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue command.

value `property` ¶

value: TriggerABusBItemSpiDataInValue

Return the TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MISO or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue?

Info

<QString> is the binary data string, where the number of bits is 8 times the number of bytes specified. The only allowed characters in the string are 0, 1, and X.

TriggerABusBItemSpiDataInValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MISO or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:IN:VALue?

Info

<QString> is the binary data string, where the number of bits is 8 times the number of bytes specified. The only allowed characters in the string are 0, 1, and X.

TriggerABusBItemSpiDataMiso ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:MISO command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue command.

value `property` ¶

value: TriggerABusBItemSpiDataMisoValue

Return the TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MISO or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue?

Info

<QString> is the binary data string, where the number of bits is 8 times the number of bytes specified. The only allowed characters in the string are 0, 1, and X.

TriggerABusBItemSpiDataMisoValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MISO or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:MISO:VALue?

Info

<QString> is the binary data string, where the number of bits is 8 times the number of bytes specified. The only allowed characters in the string are 0, 1, and X.

TriggerABusBItemSpiDataMosi ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:MOSI command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue command.

value `property` ¶

value: TriggerABusBItemSpiDataMosiValue

Return the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MOSI or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue?

Info

<QString> is the binary data string with the number of bits specified by the TRIGGER:A:BUS:BX:SPI:DATA:SIZE command. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemSpiDataMosiValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MOSI or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:MOSI:VALue?

Info

<QString> is the binary data string with the number of bits specified by the TRIGGER:A:BUS:BX:SPI:DATA:SIZE command. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemSpiDataOut ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:OUT command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue command.

value `property` ¶

value: TriggerABusBItemSpiDataOutValue

Return the TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MOSI or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue?

Info

<QString> is the binary data string with the number of bits specified by the TRIGGER:A:BUS:BX:SPI:DATA:SIZE command. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemSpiDataOutValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue command.

Description

This command specifies the binary data string to be used for a SPI trigger if the trigger condition is MOSI or MISOMOSI. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue <QString>
- TRIGger:A:BUS:B<x>:SPI:DATa:OUT:VALue?

Info

<QString> is the binary data string with the number of bits specified by the TRIGGER:A:BUS:BX:SPI:DATA:SIZE command. The only allowed characters in the QString are 0, 1, and X.

TriggerABusBItemSpiDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:SPI:DATa:SIZe command.

Description

This command specifies the length of the data string to be used for a SPI trigger if the trigger condition is DATa. B is the specified bus number.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:SPI:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:SPI:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:SPI:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:SPI:DATa:SIZe?

Info

<NR1> is the length of the data string in bytes.

TriggerABusBItemUsb ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB? query and raise an AssertionError if the returned value does not match value.

Properties

.address: The TRIGger:A:BUS:B<x>:USB:ADDRess command tree.
.condition: The TRIGger:A:BUS:B<x>:USB:CONDition command.
.data: The TRIGger:A:BUS:B<x>:USB:DATa command tree.
.endpoint: The TRIGger:A:BUS:B<x>:USB:ENDPoint command tree.
.errtype: The TRIGger:A:BUS:B<x>:USB:ERRTYPE command.
.handshaketype: The TRIGger:A:BUS:B<x>:USB:HANDSHAKEType command.
.qualifier: The TRIGger:A:BUS:B<x>:USB:QUALifier command.
.sofframenumber: The TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber command.
.specialtype: The TRIGger:A:BUS:B<x>:USB:SPECIALType command.
.split: The TRIGger:A:BUS:B<x>:USB:SPLit command tree.
.tokentype: The TRIGger:A:BUS:B<x>:USB:TOKENType command.

address `property` ¶

address: TriggerABusBItemUsbAddress

Return the TRIGger:A:BUS:B<x>:USB:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue command.
.value: The TRIGger:A:BUS:B<x>:USB:ADDRess:VALue command.

condition `property` ¶

condition: TriggerABusBItemUsbCondition

Return the TRIGger:A:BUS:B<x>:USB:CONDition command.

Description

This command specifies the trigger condition for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:CONDition {SYNC|RESET|SUSPEND|RESUME|EOP|TOKENPacket|DATAPacket|HANDSHAKEPacket|SPECIALPacket|ERRor}
- TRIGger:A:BUS:B<x>:USB:CONDition?

Info

SYNC indicates triggering on a Sync field of a packet.
RESET sets triggering on a reset condition.
SUSPEND sets triggering on a suspend condition.
RESUME sets triggering on a resume condition.
EOP indicates triggering on an end-of-packet signal.
TOKENPacket indicates triggering on a token packet.
DATAPacket indicates triggering on a data packet.
HANDSHAKEPacket indicates triggering on a handshake packet.
SPECIALPacket indicates triggering on a special status packet.
ERRor indicates triggering on an error condition.

data `property` ¶

data: TriggerABusBItemUsbData

Return the TRIGger:A:BUS:B<x>:USB:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.hivalue: The TRIGger:A:BUS:B<x>:USB:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:USB:DATa:OFFSet command.
.size: The TRIGger:A:BUS:B<x>:USB:DATa:SIZe command.
.type: The TRIGger:A:BUS:B<x>:USB:DATa:TYPe command.
.value: The TRIGger:A:BUS:B<x>:USB:DATa:VALue command.

endpoint `property` ¶

endpoint: TriggerABusBItemUsbEndpoint

Return the TRIGger:A:BUS:B<x>:USB:ENDPoint command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue command.

errtype `property` ¶

errtype: TriggerABusBItemUsbErrtype

Return the TRIGger:A:BUS:B<x>:USB:ERRTYPE command.

Description

This command specifies the error type to be used when the trigger condition is set to ERRor. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ERRTYPE {PID|CRC5|CRC16|BITSTUFFing}
- TRIGger:A:BUS:B<x>:USB:ERRTYPE?

Info

PID indicates the error type is set to packet ID.
CRC5 indicates the error type is set to 5-bit CRC.
CRC16 indicates the error type is set to 16-bit CRC.
BITSTUFFing indicates the error type is set to bit stuffing.

handshaketype `property` ¶

handshaketype: TriggerABusBItemUsbHandshaketype

Return the TRIGger:A:BUS:B<x>:USB:HANDSHAKEType command.

Description

This command specifies the handshake type for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:HANDSHAKEType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:HANDSHAKEType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:HANDSHAKEType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:HANDSHAKEType {ANY|NAK|ACK|STALL}
- TRIGger:A:BUS:B<x>:USB:HANDSHAKEType?

Info

ANY indicates the oscilloscope will trigger on any handshake type.
NAK indicates the oscilloscope will trigger when a device cannot send or receive data.
ACK indicates the oscilloscope will trigger when a packet is successfully received.
STALL indicates the oscilloscope will trigger when a device requires intervention from the host.

qualifier `property` ¶

qualifier: TriggerABusBItemUsbQualifier

Return the TRIGger:A:BUS:B<x>:USB:QUALifier command.

Description

This command specifies the USB trigger qualifier for address, endpoint and data. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:USB:QUALifier?

Info

LESSthan triggers on an input value that is less than a set value.
MOREthan triggers on an input value that is greater than a set value.
EQual triggers on an input value that is equal to a set value.
UNEQual triggers on an input value that is not equal to a set value.
LESSEQual triggers on an input value that is less than or equal to a set value.
MOREEQual triggers on an input value that is more than or equal to a set value.
INrange triggers on an input value that is within a range set by two values.
OUTrange triggers on an input value that is outside of a range set by two values.

sofframenumber `property` ¶

sofframenumber: TriggerABusBItemUsbSofframenumber

Return the TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber command.

Description

This command specifies the binary data string to be used for start of frame number, when the trigger condition is Token Packet and the token type is Start of Frame. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber <QString>
- TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber?

Info

<QString> within the range 000 0000 0000 to 111 1111 1111 (000 hex to 7FF hex).

specialtype `property` ¶

specialtype: TriggerABusBItemUsbSpecialtype

Return the TRIGger:A:BUS:B<x>:USB:SPECIALType command.

Description

This command specifies the packet ID (PID) for the special packet. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPECIALType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPECIALType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPECIALType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPECIALType {ANY|PREamble|RESERVed}
- TRIGger:A:BUS:B<x>:USB:SPECIALType?

Info

ANY indicates any type of special packet.
PREamble indicates a preamble special packet.
RESERVed indicates a reserved special packet.

split `property` ¶

split: TriggerABusBItemUsbSplit

Return the TRIGger:A:BUS:B<x>:USB:SPLit command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.et: The TRIGger:A:BUS:B<x>:USB:SPLit:ET command tree.
.hub: The TRIGger:A:BUS:B<x>:USB:SPLit:HUB command tree.
.port: The TRIGger:A:BUS:B<x>:USB:SPLit:PORT command tree.
.sc: The TRIGger:A:BUS:B<x>:USB:SPLit:SC command tree.
.se: The TRIGger:A:BUS:B<x>:USB:SPLit:SE command tree.

tokentype `property` ¶

tokentype: TriggerABusBItemUsbTokentype

Return the TRIGger:A:BUS:B<x>:USB:TOKENType command.

Description

This command specifies the token type for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:TOKENType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:TOKENType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:TOKENType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:TOKENType {ANY|SOF|OUT|IN|SETUP}
- TRIGger:A:BUS:B<x>:USB:TOKENType?

Info

ANY
SOF indicates a SOF (start-of-frame) token type.
OUT indicates an OUT token type.
IN indicates an IN token type.
SETUP indicates a SETUP token type.

TriggerABusBItemUsbAddress ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:ADDRess command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ADDRess? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue command.
.value: The TRIGger:A:BUS:B<x>:USB:ADDRess:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemUsbAddressHivalue

Return the TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue command.

Description

This command specifies the binary address string for the upper limit for inside-of-range and outside-of-range qualifiers for the USB trigger. Use the command TRIGGER:A:BUS:BX:USB:ADDRESS:VALUE to set the lower limit. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue?

Info

<QString> within the range 0000000 to 1111111 (00 hex to 7F hex).

value `property` ¶

value: TriggerABusBItemUsbAddressValue

Return the TRIGger:A:BUS:B<x>:USB:ADDRess:VALue command.

Description

This command specifies the binary address string to be used for USB trigger. This command also specifies the binary address string for the lower limit for inside-of-range and outside-of-range qualifiers for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ADDRess:VALue <Qstring>
- TRIGger:A:BUS:B<x>:USB:ADDRess:VALue?

Info

<QString> within the range 0000000 to 1111111 (00 hex to 7F hex).

TriggerABusBItemUsbAddressHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue command.

Description

This command specifies the binary address string for the upper limit for inside-of-range and outside-of-range qualifiers for the USB trigger. Use the command TRIGGER:A:BUS:BX:USB:ADDRESS:VALUE to set the lower limit. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue <QString>
- TRIGger:A:BUS:B<x>:USB:ADDRess:HIVALue?

Info

<QString> within the range 0000000 to 1111111 (00 hex to 7F hex).

TriggerABusBItemUsbAddressValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:ADDRess:VALue command.

Description

This command specifies the binary address string to be used for USB trigger. This command also specifies the binary address string for the lower limit for inside-of-range and outside-of-range qualifiers for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ADDRess:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ADDRess:VALue <Qstring>
- TRIGger:A:BUS:B<x>:USB:ADDRess:VALue?

Info

<QString> within the range 0000000 to 1111111 (00 hex to 7F hex).

TriggerABusBItemUsbCondition ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:CONDition command.

Description

This command specifies the trigger condition for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:CONDition? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:CONDition? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:CONDition value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:CONDition {SYNC|RESET|SUSPEND|RESUME|EOP|TOKENPacket|DATAPacket|HANDSHAKEPacket|SPECIALPacket|ERRor}
- TRIGger:A:BUS:B<x>:USB:CONDition?

Info

SYNC indicates triggering on a Sync field of a packet.
RESET sets triggering on a reset condition.
SUSPEND sets triggering on a suspend condition.
RESUME sets triggering on a resume condition.
EOP indicates triggering on an end-of-packet signal.
TOKENPacket indicates triggering on a token packet.
DATAPacket indicates triggering on a data packet.
HANDSHAKEPacket indicates triggering on a handshake packet.
SPECIALPacket indicates triggering on a special status packet.
ERRor indicates triggering on an error condition.

TriggerABusBItemUsbData ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:DATa command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa? query and raise an AssertionError if the returned value does not match value.

Properties

.hivalue: The TRIGger:A:BUS:B<x>:USB:DATa:HIVALue command.
.offset: The TRIGger:A:BUS:B<x>:USB:DATa:OFFSet command.
.size: The TRIGger:A:BUS:B<x>:USB:DATa:SIZe command.
.type: The TRIGger:A:BUS:B<x>:USB:DATa:TYPe command.
.value: The TRIGger:A:BUS:B<x>:USB:DATa:VALue command.

hivalue `property` ¶

hivalue: TriggerABusBItemUsbDataHivalue

Return the TRIGger:A:BUS:B<x>:USB:DATa:HIVALue command.

Description

This command specifies the binary data string for the upper limit for inside-of-range and outside-of-range qualifiers for the USB trigger when the trigger condition is DATAPacket. Use the command TRIGGER:A:BUS:BX:USB:DATA:VALUE to set the lower limit. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:USB:DATa:HIVALue?

Info

<QString> within the range 00000000 to 11111111 (00 hex to FF hex).

offset `property` ¶

offset: TriggerABusBItemUsbDataOffset

Return the TRIGger:A:BUS:B<x>:USB:DATa:OFFSet command.

Description

This command specifies the data offset in bytes to trigger on. The minimum and default values are 0 and the maximum is 1024. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:USB:DATa:OFFSet?

size `property` ¶

size: TriggerABusBItemUsbDataSize

Return the TRIGger:A:BUS:B<x>:USB:DATa:SIZe command.

Description

This command specifies the number of contiguous data bytes to trigger on. The minimum and default values are 1 and maximum is 16. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:USB:DATa:SIZe?

type `property` ¶

type: TriggerABusBItemUsbDataType

Return the TRIGger:A:BUS:B<x>:USB:DATa:TYPe command.

Description

This command specifies the data type for when the trigger condition is set to DATAPacket. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:TYPe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:TYPe {ANY|DATA<x>}
- TRIGger:A:BUS:B<x>:USB:DATa:TYPe?

Info

ANY indicates either a DATA0 or DATA1 data packet type.
DATA0 indicates a DATA0 data packet type.
DATA1 indicates a DATA1 data packet type.

value `property` ¶

value: TriggerABusBItemUsbDataValue

Return the TRIGger:A:BUS:B<x>:USB:DATa:VALue command.

Description

This command specifies the binary data string to be used for the USB trigger when the trigger condition is DATAPacket. This command also specifies the binary data string for the lower limit for inside-of-range and outside-of-range qualifiers for the USB trigger when trigger condition is DATAPacket. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:DATa:VALue?

Info

<QString> within the range 00000000 to 11111111 (00 hex to FF hex).

TriggerABusBItemUsbDataHivalue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:DATa:HIVALue command.

Description

This command specifies the binary data string for the upper limit for inside-of-range and outside-of-range qualifiers for the USB trigger when the trigger condition is DATAPacket. Use the command TRIGGER:A:BUS:BX:USB:DATA:VALUE to set the lower limit. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:HIVALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:HIVALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:HIVALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:HIVALue <QString>
- TRIGger:A:BUS:B<x>:USB:DATa:HIVALue?

Info

<QString> within the range 00000000 to 11111111 (00 hex to FF hex).

TriggerABusBItemUsbDataOffset ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:DATa:OFFSet command.

Description

This command specifies the data offset in bytes to trigger on. The minimum and default values are 0 and the maximum is 1024. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:OFFSet? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:OFFSet? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:OFFSet value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:OFFSet <NR1>
- TRIGger:A:BUS:B<x>:USB:DATa:OFFSet?

TriggerABusBItemUsbDataSize ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:DATa:SIZe command.

Description

This command specifies the number of contiguous data bytes to trigger on. The minimum and default values are 1 and maximum is 16. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:SIZe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:SIZe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:SIZe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:SIZe <NR1>
- TRIGger:A:BUS:B<x>:USB:DATa:SIZe?

TriggerABusBItemUsbDataType ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:DATa:TYPe command.

Description

This command specifies the data type for when the trigger condition is set to DATAPacket. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:TYPe value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:TYPe {ANY|DATA<x>}
- TRIGger:A:BUS:B<x>:USB:DATa:TYPe?

Info

ANY indicates either a DATA0 or DATA1 data packet type.
DATA0 indicates a DATA0 data packet type.
DATA1 indicates a DATA1 data packet type.

TriggerABusBItemUsbDataValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:DATa:VALue command.

Description

This command specifies the binary data string to be used for the USB trigger when the trigger condition is DATAPacket. This command also specifies the binary data string for the lower limit for inside-of-range and outside-of-range qualifiers for the USB trigger when trigger condition is DATAPacket. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:DATa:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:DATa:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:DATa:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:DATa:VALue?

Info

<QString> within the range 00000000 to 11111111 (00 hex to FF hex).

TriggerABusBItemUsbEndpoint ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:ENDPoint command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue command.

value `property` ¶

value: TriggerABusBItemUsbEndpointValue

Return the TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue command.

Description

This command specifies the binary endpoint string to be used for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue?

Info

<QString> within the range 0000 to 1111 (00 hex to 0F hex).

TriggerABusBItemUsbEndpointValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue command.

Description

This command specifies the binary endpoint string to be used for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:ENDPoint:VALue?

Info

<QString> within the range 0000 to 1111 (00 hex to 0F hex).

TriggerABusBItemUsbErrtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:ERRTYPE command.

Description

This command specifies the error type to be used when the trigger condition is set to ERRor. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:ERRTYPE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:ERRTYPE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:ERRTYPE value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:ERRTYPE {PID|CRC5|CRC16|BITSTUFFing}
- TRIGger:A:BUS:B<x>:USB:ERRTYPE?

Info

PID indicates the error type is set to packet ID.
CRC5 indicates the error type is set to 5-bit CRC.
CRC16 indicates the error type is set to 16-bit CRC.
BITSTUFFing indicates the error type is set to bit stuffing.

TriggerABusBItemUsbHandshaketype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:HANDSHAKEType command.

Description

This command specifies the handshake type for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:HANDSHAKEType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:HANDSHAKEType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:HANDSHAKEType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:HANDSHAKEType {ANY|NAK|ACK|STALL}
- TRIGger:A:BUS:B<x>:USB:HANDSHAKEType?

Info

ANY indicates the oscilloscope will trigger on any handshake type.
NAK indicates the oscilloscope will trigger when a device cannot send or receive data.
ACK indicates the oscilloscope will trigger when a packet is successfully received.
STALL indicates the oscilloscope will trigger when a device requires intervention from the host.

TriggerABusBItemUsbQualifier ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:QUALifier command.

Description

This command specifies the USB trigger qualifier for address, endpoint and data. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:QUALifier? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:QUALifier? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:QUALifier value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:QUALifier {LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|INrange|OUTrange}
- TRIGger:A:BUS:B<x>:USB:QUALifier?

Info

LESSthan triggers on an input value that is less than a set value.
MOREthan triggers on an input value that is greater than a set value.
EQual triggers on an input value that is equal to a set value.
UNEQual triggers on an input value that is not equal to a set value.
LESSEQual triggers on an input value that is less than or equal to a set value.
MOREEQual triggers on an input value that is more than or equal to a set value.
INrange triggers on an input value that is within a range set by two values.
OUTrange triggers on an input value that is outside of a range set by two values.

TriggerABusBItemUsbSofframenumber ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber command.

Description

This command specifies the binary data string to be used for start of frame number, when the trigger condition is Token Packet and the token type is Start of Frame. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber <QString>
- TRIGger:A:BUS:B<x>:USB:SOFFRAMENUMber?

Info

<QString> within the range 000 0000 0000 to 111 1111 1111 (000 hex to 7FF hex).

TriggerABusBItemUsbSpecialtype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPECIALType command.

Description

This command specifies the packet ID (PID) for the special packet. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPECIALType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPECIALType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPECIALType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPECIALType {ANY|PREamble|RESERVed}
- TRIGger:A:BUS:B<x>:USB:SPECIALType?

Info

ANY indicates any type of special packet.
PREamble indicates a preamble special packet.
RESERVed indicates a reserved special packet.

TriggerABusBItemUsbSplit ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit? query and raise an AssertionError if the returned value does not match value.

Properties

.et: The TRIGger:A:BUS:B<x>:USB:SPLit:ET command tree.
.hub: The TRIGger:A:BUS:B<x>:USB:SPLit:HUB command tree.
.port: The TRIGger:A:BUS:B<x>:USB:SPLit:PORT command tree.
.sc: The TRIGger:A:BUS:B<x>:USB:SPLit:SC command tree.
.se: The TRIGger:A:BUS:B<x>:USB:SPLit:SE command tree.

et `property` ¶

et: TriggerABusBItemUsbSplitEt

Return the TRIGger:A:BUS:B<x>:USB:SPLit:ET command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue command.

hub `property` ¶

hub: TriggerABusBItemUsbSplitHub

Return the TRIGger:A:BUS:B<x>:USB:SPLit:HUB command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue command.

port `property` ¶

port: TriggerABusBItemUsbSplitPort

Return the TRIGger:A:BUS:B<x>:USB:SPLit:PORT command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue command.

sc `property` ¶

sc: TriggerABusBItemUsbSplitSc

Return the TRIGger:A:BUS:B<x>:USB:SPLit:SC command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue command.

se `property` ¶

se: TriggerABusBItemUsbSplitSe

Return the TRIGger:A:BUS:B<x>:USB:SPLit:SE command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue command.

TriggerABusBItemUsbSplitEt ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:ET command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue command.

value `property` ¶

value: TriggerABusBItemUsbSplitEtValue

Return the TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction endpoint type value to trigger on. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue {NOCARE|CONTRol|ISOchronous|BULK|INTERRUPT}
- TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue?

Info

NOCARE - any endpoint type.
CONTRol - control endpoint type.
ISOchronous - isochronous endpoint type.
BULK - bulk endpoint type (BULK-IN or BULK-OUT).
INTERRUPT - interrupt endpoint type (Interrupt-IN).

TriggerABusBItemUsbSplitEtValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction endpoint type value to trigger on. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue {NOCARE|CONTRol|ISOchronous|BULK|INTERRUPT}
- TRIGger:A:BUS:B<x>:USB:SPLit:ET:VALue?

Info

NOCARE - any endpoint type.
CONTRol - control endpoint type.
ISOchronous - isochronous endpoint type.
BULK - bulk endpoint type (BULK-IN or BULK-OUT).
INTERRUPT - interrupt endpoint type (Interrupt-IN).

TriggerABusBItemUsbSplitHub ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:HUB command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue command.

value `property` ¶

value: TriggerABusBItemUsbSplitHubValue

Return the TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction hub address value to trigger on. The value can be up to 7 characters long. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue?

Info

QString is a quoted string of up to 7 characters. The valid characters are 0 and 1.

TriggerABusBItemUsbSplitHubValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction hub address value to trigger on. The value can be up to 7 characters long. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:SPLit:HUB:VALue?

Info

QString is a quoted string of up to 7 characters. The valid characters are 0 and 1.

TriggerABusBItemUsbSplitPort ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:PORT command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue command.

value `property` ¶

value: TriggerABusBItemUsbSplitPortValue

Return the TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction port address value to trigger on. The value can be up to 7 characters long. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue?

Info

QString is a quoted string of up to 7 characters. The valid characters are 0 and 1.

TriggerABusBItemUsbSplitPortValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction port address value to trigger on. The value can be up to 7 characters long. The default is all X’s (don’t care). B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue <QString>
- TRIGger:A:BUS:B<x>:USB:SPLit:PORT:VALue?

Info

QString is a quoted string of up to 7 characters. The valid characters are 0 and 1.

TriggerABusBItemUsbSplitSc ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:SC command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue command.

value `property` ¶

value: TriggerABusBItemUsbSplitScValue

Return the TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies whether to trigger on the start or complete phase of the split transaction, based on the Start/Complete bit field value. (0 = Start, 1 = Complete). The default is NOCARE. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue {NOCARE|SSPLIT|CSPLIT}
- TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue?

Info

NOCARE - trigger on either the start or complete phase of the split transaction.
SSPLIT - trigger on the start phase of the split transaction.
CSPLIT - trigger on the complete phase of the split transaction.

TriggerABusBItemUsbSplitScValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies whether to trigger on the start or complete phase of the split transaction, based on the Start/Complete bit field value. (0 = Start, 1 = Complete). The default is NOCARE. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue {NOCARE|SSPLIT|CSPLIT}
- TRIGger:A:BUS:B<x>:USB:SPLit:SC:VALue?

Info

NOCARE - trigger on either the start or complete phase of the split transaction.
SSPLIT - trigger on the start phase of the split transaction.
CSPLIT - trigger on the complete phase of the split transaction.

TriggerABusBItemUsbSplitSe ¶

Bases: SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:SE command tree.

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE? query and raise an AssertionError if the returned value does not match value.

Properties

.value: The TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue command.

value `property` ¶

value: TriggerABusBItemUsbSplitSeValue

Return the TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction start/end bit value to trigger on. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue {NOCARE|FULLSPeed|LOWSPeed|ISOSTART|ISOMID|ISOEND|ISOALL}
- TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue?

Info

NOCARE - any combination of S and E bits.
FULLSPeed - S bit = 0, E bit = 0.
LOWSPeed - S bit = 1, E bit = 0.
ISOSTART - S bit = 1, E bit = 0.
ISOMID - see note above.
ISOEND - see note above.
ISOALL - see note above.

TriggerABusBItemUsbSplitSeValue ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue command.

Description

When triggering on a high-speed USB split transaction, this command specifies the split transaction start/end bit value to trigger on. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue {NOCARE|FULLSPeed|LOWSPeed|ISOSTART|ISOMID|ISOEND|ISOALL}
- TRIGger:A:BUS:B<x>:USB:SPLit:SE:VALue?

Info

NOCARE - any combination of S and E bits.
FULLSPeed - S bit = 0, E bit = 0.
LOWSPeed - S bit = 1, E bit = 0.
ISOSTART - S bit = 1, E bit = 0.
ISOMID - see note above.
ISOEND - see note above.
ISOALL - see note above.

TriggerABusBItemUsbTokentype ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:B<x>:USB:TOKENType command.

Description

This command specifies the token type for the USB trigger. B

Usage

Using the .query() method will send the TRIGger:A:BUS:B<x>:USB:TOKENType? query.
Using the .verify(value) method will send the TRIGger:A:BUS:B<x>:USB:TOKENType? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:B<x>:USB:TOKENType value command.

SCPI Syntax

- TRIGger:A:BUS:B<x>:USB:TOKENType {ANY|SOF|OUT|IN|SETUP}
- TRIGger:A:BUS:B<x>:USB:TOKENType?

Info

ANY
SOF indicates a SOF (start-of-frame) token type.
OUT indicates an OUT token type.
IN indicates an IN token type.
SETUP indicates a SETUP token type.

TriggerABusSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:BUS:SOUrce command.

Description

This command specifies the source for a serial or parallel bus trigger, with the appropriate application module installed.

Usage

Using the .query() method will send the TRIGger:A:BUS:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:BUS:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:BUS:SOUrce value command.

SCPI Syntax

- TRIGger:A:BUS:SOUrce {B<x>}
- TRIGger:A:BUS:SOUrce?

Info

B1 specifies the Bus 1 source.
B2 specifies the Bus 2 source.
B3 specifies the Bus 3 source.
B4 specifies the Bus 4 source.

TriggerAEdge ¶

Bases: SCPICmdRead

The TRIGger:A:EDGE command.

Description

Returns the trigger source, coupling, and slope for the A edge trigger.

Usage

Using the .query() method will send the TRIGger:A:EDGE? query.
Using the .verify(value) method will send the TRIGger:A:EDGE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:EDGE?

Properties

.coupling: The TRIGger:A:EDGE:COUPling command.
.slope: The TRIGger:A:EDGE:SLOpe command.
.source: The TRIGger:A:EDGE:SOUrce command.

coupling `property` ¶

coupling: TriggerAEdgeCoupling

Return the TRIGger:A:EDGE:COUPling command.

Description

This command specifies the type of coupling for the A edge trigger.

Usage

Using the .query() method will send the TRIGger:A:EDGE:COUPling? query.
Using the .verify(value) method will send the TRIGger:A:EDGE:COUPling? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:EDGE:COUPling value command.

SCPI Syntax

- TRIGger:A:EDGE:COUPling {AC|DC|HFRej|LFRej|NOISErej}
- TRIGger:A:EDGE:COUPling?

Info

AC specifies AC trigger coupling.
DC specifies DC trigger coupling, which passes all input signals to the trigger circuitry.
HFRej specifies high-frequency rejection coupling, which attenuates signals above 50 kHz before passing the signals to the trigger circuitry.
LFRej specifies low-frequency rejection coupling, which attenuates signals below 50 kHz before passing the signals to the trigger circuitry.
NOISErej specifies noise-rejection coupling, which provides stable triggering by increasing the trigger hysteresis. Increased hysteresis reduces the trigger sensitivity to noise but may require greater trigger signal amplitude.

slope `property` ¶

slope: TriggerAEdgeSlope

Return the TRIGger:A:EDGE:SLOpe command.

Description

This command specifies the slope for the A edge trigger: rising, falling or either.

Usage

Using the .query() method will send the TRIGger:A:EDGE:SLOpe? query.
Using the .verify(value) method will send the TRIGger:A:EDGE:SLOpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:EDGE:SLOpe value command.

SCPI Syntax

- TRIGger:A:EDGE:SLOpe {RISe|FALL|EITHer}
- TRIGger:A:EDGE:SLOpe?

Info

RISe specifies to trigger on the rising or positive edge of a signal.
FALL specifies to trigger on the falling or negative edge of a signal.
EITHer specifies to trigger on either the rising or falling edge of a signal.

source `property` ¶

source: TriggerAEdgeSource

Return the TRIGger:A:EDGE:SOUrce command.

Description

This command specifies the source for the A edge trigger.

Usage

Using the .query() method will send the TRIGger:A:EDGE:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:EDGE:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:EDGE:SOUrce value command.

SCPI Syntax

- TRIGger:A:EDGE:SOUrce {AUX|CH<x>|D<x>|LINE|RF}
- TRIGger:A:EDGE:SOUrce?

Info

AUX specifies an external trigger using the auxiliary input connector located on the front panel of the oscilloscope. (For 2-channel MDO32 model only.).
CH<x> specifies an analog input channel as the A edge trigger source.
D<x> specifies a digital channel as the source (only with option 3-MSO installed).
LINE specifies the AC power line as the trigger source.

TriggerAEdgeCoupling ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:EDGE:COUPling command.

Description

This command specifies the type of coupling for the A edge trigger.

Usage

Using the .query() method will send the TRIGger:A:EDGE:COUPling? query.
Using the .verify(value) method will send the TRIGger:A:EDGE:COUPling? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:EDGE:COUPling value command.

SCPI Syntax

- TRIGger:A:EDGE:COUPling {AC|DC|HFRej|LFRej|NOISErej}
- TRIGger:A:EDGE:COUPling?

Info

AC specifies AC trigger coupling.
DC specifies DC trigger coupling, which passes all input signals to the trigger circuitry.
HFRej specifies high-frequency rejection coupling, which attenuates signals above 50 kHz before passing the signals to the trigger circuitry.
LFRej specifies low-frequency rejection coupling, which attenuates signals below 50 kHz before passing the signals to the trigger circuitry.
NOISErej specifies noise-rejection coupling, which provides stable triggering by increasing the trigger hysteresis. Increased hysteresis reduces the trigger sensitivity to noise but may require greater trigger signal amplitude.

TriggerAEdgeSlope ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:EDGE:SLOpe command.

Description

This command specifies the slope for the A edge trigger: rising, falling or either.

Usage

Using the .query() method will send the TRIGger:A:EDGE:SLOpe? query.
Using the .verify(value) method will send the TRIGger:A:EDGE:SLOpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:EDGE:SLOpe value command.

SCPI Syntax

- TRIGger:A:EDGE:SLOpe {RISe|FALL|EITHer}
- TRIGger:A:EDGE:SLOpe?

Info

RISe specifies to trigger on the rising or positive edge of a signal.
FALL specifies to trigger on the falling or negative edge of a signal.
EITHer specifies to trigger on either the rising or falling edge of a signal.

TriggerAEdgeSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:EDGE:SOUrce command.

Description

This command specifies the source for the A edge trigger.

Usage

Using the .query() method will send the TRIGger:A:EDGE:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:EDGE:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:EDGE:SOUrce value command.

SCPI Syntax

- TRIGger:A:EDGE:SOUrce {AUX|CH<x>|D<x>|LINE|RF}
- TRIGger:A:EDGE:SOUrce?

Info

AUX specifies an external trigger using the auxiliary input connector located on the front panel of the oscilloscope. (For 2-channel MDO32 model only.).
CH<x> specifies an analog input channel as the A edge trigger source.
D<x> specifies a digital channel as the source (only with option 3-MSO installed).
LINE specifies the AC power line as the trigger source.

TriggerAHoldoff ¶

Bases: SCPICmdRead

The TRIGger:A:HOLDoff command.

Description

Returns the A trigger holdoff parameters. These parameters specify the time period during which the trigger circuitry is not looking to generate a trigger event.

Usage

Using the .query() method will send the TRIGger:A:HOLDoff? query.
Using the .verify(value) method will send the TRIGger:A:HOLDoff? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:HOLDoff?

Properties

.time: The TRIGger:A:HOLDoff:TIMe command.

time `property` ¶

time: TriggerAHoldoffTime

Return the TRIGger:A:HOLDoff:TIMe command.

Description

This command sets or queries the A trigger holdoff time. This command is equivalent to selecting Mode & Holdoff from the Trig menu, selecting Time, and then setting the desired Holdoff Time.

Usage

Using the .query() method will send the TRIGger:A:HOLDoff:TIMe? query.
Using the .verify(value) method will send the TRIGger:A:HOLDoff:TIMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:HOLDoff:TIMe value command.

SCPI Syntax

- TRIGger:A:HOLDoff:TIMe <NR3>
- TRIGger:A:HOLDoff:TIMe?

Info

<NR3> specifies the holdoff time in seconds. The range is from 0 seconds through 10 seconds.

TriggerAHoldoffTime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:HOLDoff:TIMe command.

Description

This command sets or queries the A trigger holdoff time. This command is equivalent to selecting Mode & Holdoff from the Trig menu, selecting Time, and then setting the desired Holdoff Time.

Usage

Using the .query() method will send the TRIGger:A:HOLDoff:TIMe? query.
Using the .verify(value) method will send the TRIGger:A:HOLDoff:TIMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:HOLDoff:TIMe value command.

SCPI Syntax

- TRIGger:A:HOLDoff:TIMe <NR3>
- TRIGger:A:HOLDoff:TIMe?

Info

<NR3> specifies the holdoff time in seconds. The range is from 0 seconds through 10 seconds.

TriggerALevel ¶

Bases: SCPICmdRead

The TRIGger:A:LEVel command tree.

Usage

Using the .query() method will send the TRIGger:A:LEVel? query.
Using the .verify(value) method will send the TRIGger:A:LEVel? query and raise an AssertionError if the returned value does not match value.

Properties

.auxin: The TRIGger:A:LEVel:AUXin command.
.ch: The TRIGger:A:LEVel:CH<x> command.
.d: The TRIGger:A:LEVel:D<x> command.

auxin `property` ¶

auxin: TriggerALevelAuxin

Return the TRIGger:A:LEVel:AUXin command.

Description

This command sets the threshold voltage level to use for an Edge, Pulse Width, Runt or Rise/Fall (aka Transition, aka Slew Rate) trigger when triggering on the Aux Input connector signal.

Usage

Using the .query() method will send the TRIGger:A:LEVel:AUXin? query.
Using the .verify(value) method will send the TRIGger:A:LEVel:AUXin? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LEVel:AUXin value command.

SCPI Syntax

- TRIGger:A:LEVel:AUXin {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:AUXin?

Info

<NR3> is a floating point number that sets the trigger threshold level, in Volts, for the Aux Input connector.
ECL sets the threshold level to a preset ECL high level of -1.3V.
TTL sets the threshold level to a preset TTL high level of 1.4V.

ch `property` ¶

ch: dict[int, TriggerALevelChannel]

Return the TRIGger:A:LEVel:CH<x> command.

Description

This command sets the threshold voltage level to use for an Edge, Pulse Width, Runt or Rise/Fall (aka Transition, aka Slew Rate) trigger when triggering on an analog channel waveform. x can be 1 - 4. Each channel can have an independent trigger level.

Usage

Using the .query() method will send the TRIGger:A:LEVel:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LEVel:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LEVel:CH<x> value command.

SCPI Syntax

- TRIGger:A:LEVel:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:CH<x>?

Info

<NR3> is a floating point number that sets the trigger threshold level, in Volts, for the specified analog channel.
ECL sets the threshold level to a preset ECL high level of -1.3V.
TTL sets the threshold level to a preset TTL high level of 1.4V.

d `property` ¶

d: dict[int, TriggerALevelDigitalBit]

Return the TRIGger:A:LEVel:D<x> command.

Description

This command sets the threshold voltage level to use for an Edge or Pulse Width trigger when triggering on a digital channel waveform. can be 1 - 16. Each channel can have an independent trigger level.

Usage

Using the .query() method will send the TRIGger:A:LEVel:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LEVel:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LEVel:D<x> value command.

SCPI Syntax

- TRIGger:A:LEVel:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:D<x>?

Info

<NR3> is a floating point number that sets the trigger threshold level, in Volts, for the specified digital channel.
ECL sets the threshold level to a preset ECL high level of -1.3V.
TTL sets the threshold level to a preset TTL high level of 1.4V.

TriggerALevelAuxin ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LEVel:AUXin command.

Description

This command sets the threshold voltage level to use for an Edge, Pulse Width, Runt or Rise/Fall (aka Transition, aka Slew Rate) trigger when triggering on the Aux Input connector signal.

Usage

Using the .query() method will send the TRIGger:A:LEVel:AUXin? query.
Using the .verify(value) method will send the TRIGger:A:LEVel:AUXin? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LEVel:AUXin value command.

SCPI Syntax

- TRIGger:A:LEVel:AUXin {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:AUXin?

Info

<NR3> is a floating point number that sets the trigger threshold level, in Volts, for the Aux Input connector.
ECL sets the threshold level to a preset ECL high level of -1.3V.
TTL sets the threshold level to a preset TTL high level of 1.4V.

TriggerALevelChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LEVel:CH<x> command.

Description

This command sets the threshold voltage level to use for an Edge, Pulse Width, Runt or Rise/Fall (aka Transition, aka Slew Rate) trigger when triggering on an analog channel waveform. x can be 1 - 4. Each channel can have an independent trigger level.

Usage

Using the .query() method will send the TRIGger:A:LEVel:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LEVel:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LEVel:CH<x> value command.

SCPI Syntax

- TRIGger:A:LEVel:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:CH<x>?

Info

<NR3> is a floating point number that sets the trigger threshold level, in Volts, for the specified analog channel.
ECL sets the threshold level to a preset ECL high level of -1.3V.
TTL sets the threshold level to a preset TTL high level of 1.4V.

TriggerALevelDigitalBit ¶

Bases: ValidatedDigitalBit, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LEVel:D<x> command.

Description

This command sets the threshold voltage level to use for an Edge or Pulse Width trigger when triggering on a digital channel waveform. can be 1 - 16. Each channel can have an independent trigger level.

Usage

Using the .query() method will send the TRIGger:A:LEVel:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LEVel:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LEVel:D<x> value command.

SCPI Syntax

- TRIGger:A:LEVel:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LEVel:D<x>?

Info

<NR3> is a floating point number that sets the trigger threshold level, in Volts, for the specified digital channel.
ECL sets the threshold level to a preset ECL high level of -1.3V.
TTL sets the threshold level to a preset TTL high level of 1.4V.

TriggerALogic ¶

Bases: SCPICmdRead

The TRIGger:A:LOGIc command.

Description

Returns all of the A logic trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:LOGIc? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:LOGIc?

Properties

.class: The TRIGger:A:LOGIc:CLAss command.
.function: The TRIGger:A:LOGIc:FUNCtion command.
.input: The TRIGger:A:LOGIc:INPut command.
.pattern: The TRIGger:A:LOGIc:PATtern command.
.threshold: The TRIGger:A:LOGIc:THReshold command tree.

class_ `property` ¶

class_: TriggerALogicClass

Return the TRIGger:A:LOGIc:CLAss command.

Description

This command specifies what kind of logic trigger to use (either logic or setup/hold). You also need to set the trigger type to LOGIC using the command TRIGGER:A:TYPE. The LOGIC argument sets the oscilloscope to trigger on logical combinations of the channels (set using the TRIGger:A:LOGIc:INPut commands as well as TRIGGER:A:LOGIC:FUNCTION). You can use up to 20 channels for a logic trigger (4 analog and 16 digital). You can perform logic triggering using a clock; when TRIGGER:A:LOGIC:INPUT:CLOCK:SOURCE is set to one of the channels, the oscilloscope triggers when the specified logical combination of the remaining channels is true during a transition on the clock channel. You can also perform logic triggering without using a clock (by setting TRIGGER:A:LOGIC:INPUT:CLOCK:SOURCE to NONE ), so that the oscilloscope triggers when the specified logical combination of data channels is met. Without a clock, you can also use the command TRIGGER:A:LOGIC:PATTERN:DELTATIME. The SETHold argument sets the oscilloscope to trigger on setup and hold violations between a data source and a clock source. The clocking and data levels are used to determine if a clock or data transition has occurred. You can use up to 20 channels as Setup and Hold trigger data sources (4 analog and 16 digital) using TRIGGER:A:SETHOLD:DATA:SOURCE. You can use one channel input as the clock signal (TRIGGER:A:SETHOLD:CLOCK:SOURCE). The data sources cannot include the waveform specified for the clock source.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:CLAss? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:CLAss? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:CLAss value command.

SCPI Syntax

- TRIGger:A:LOGIc:CLAss {LOGIC|SETHold}
- TRIGger:A:LOGIc:CLAss?

Info

LOGIC - Use with the commands TRIGGER:A:LOGIC:FUNCTION, TRIGGER:A:LOGIC:INPUT:CHX, TRIGGER:A:LOGIC:INPUT:CLOCK:EDGE, TRIGGER:A:LOGIC:INPUT:CLOCK:SOURCE, TRIGGER:A:LOGIC:INPUT:DX, and TRIGGER:A:LOGIC:INPUT:RF. If you would like to use the logic trigger without a clock, you can also use the command TRIGGER:A:LOGIC:PATTERN:DELTATIME.
SETHold - Use with the commands TRIGGER:A:SETHOLD:CLOCK:EDGE, TRIGGER:A:SETHOLD:CLOCK:SOURCE, TRIGGER:A:SETHOLD:CLOCK:THRESHOLD, TRIGGER:A:SETHOLD:DATA:SOURCE.

function `property` ¶

function: TriggerALogicFunction

Return the TRIGger:A:LOGIc:FUNCtion command.

Description

This command sets or queries the logical combination of the input channels for logic triggers. This command is equivalent to selecting Logic for the Trigger Type, and setting or viewing the Define Logic.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:FUNCtion? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:FUNCtion? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:FUNCtion value command.

SCPI Syntax

- TRIGger:A:LOGIc:FUNCtion {AND|NANd|NOR|OR}
- TRIGger:A:LOGIc:FUNCtion?

Info

AND specifies to trigger if all conditions are true.
NANd specifies to trigger if any of the conditions are false.
NOR specifies to trigger if all conditions are false.
OR specifies to trigger if any of the conditions are true.

input `property` ¶

input: TriggerALogicInput

Return the TRIGger:A:LOGIc:INPut command.

Description

Returns the logic input values for all channels. If a clock channel is defined, it returns the clock source and edge.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:LOGIc:INPut?

Sub-properties

.ch: The TRIGger:A:LOGIc:INPut:CH<x> command.
.clock: The TRIGger:A:LOGIc:INPut:CLOCk command tree.
.d: The TRIGger:A:LOGIc:INPut:D<x> command.
.rf: The TRIGger:A:LOGIc:INPut:RF command.

pattern `property` ¶

pattern: TriggerALogicPattern

Return the TRIGger:A:LOGIc:PATtern command.

Description

Returns the conditions used for generating an A logic pattern trigger, with respect to the defined input pattern, and identifies the time that the selected pattern may be true and still generate the trigger.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:PATtern? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:PATtern? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:LOGIc:PATtern?

Sub-properties

.deltatime: The TRIGger:A:LOGIc:PATtern:DELTatime command.
.when: The TRIGger:A:LOGIc:PATtern:WHEn command.

threshold `property` ¶

threshold: TriggerALogicThreshold

Return the TRIGger:A:LOGIc:THReshold command tree.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.ch: The TRIGger:A:LOGIc:THReshold:CH<x> command.
.d: The TRIGger:A:LOGIc:THReshold:D<x> command.
.rf: The TRIGger:A:LOGIc:THReshold:RF command.

TriggerALogicClass ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:CLAss command.

Description

This command specifies what kind of logic trigger to use (either logic or setup/hold). You also need to set the trigger type to LOGIC using the command TRIGGER:A:TYPE. The LOGIC argument sets the oscilloscope to trigger on logical combinations of the channels (set using the TRIGger:A:LOGIc:INPut commands as well as TRIGGER:A:LOGIC:FUNCTION). You can use up to 20 channels for a logic trigger (4 analog and 16 digital). You can perform logic triggering using a clock; when TRIGGER:A:LOGIC:INPUT:CLOCK:SOURCE is set to one of the channels, the oscilloscope triggers when the specified logical combination of the remaining channels is true during a transition on the clock channel. You can also perform logic triggering without using a clock (by setting TRIGGER:A:LOGIC:INPUT:CLOCK:SOURCE to NONE ), so that the oscilloscope triggers when the specified logical combination of data channels is met. Without a clock, you can also use the command TRIGGER:A:LOGIC:PATTERN:DELTATIME. The SETHold argument sets the oscilloscope to trigger on setup and hold violations between a data source and a clock source. The clocking and data levels are used to determine if a clock or data transition has occurred. You can use up to 20 channels as Setup and Hold trigger data sources (4 analog and 16 digital) using TRIGGER:A:SETHOLD:DATA:SOURCE. You can use one channel input as the clock signal (TRIGGER:A:SETHOLD:CLOCK:SOURCE). The data sources cannot include the waveform specified for the clock source.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:CLAss? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:CLAss? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:CLAss value command.

SCPI Syntax

- TRIGger:A:LOGIc:CLAss {LOGIC|SETHold}
- TRIGger:A:LOGIc:CLAss?

Info

LOGIC - Use with the commands TRIGGER:A:LOGIC:FUNCTION, TRIGGER:A:LOGIC:INPUT:CHX, TRIGGER:A:LOGIC:INPUT:CLOCK:EDGE, TRIGGER:A:LOGIC:INPUT:CLOCK:SOURCE, TRIGGER:A:LOGIC:INPUT:DX, and TRIGGER:A:LOGIC:INPUT:RF. If you would like to use the logic trigger without a clock, you can also use the command TRIGGER:A:LOGIC:PATTERN:DELTATIME.
SETHold - Use with the commands TRIGGER:A:SETHOLD:CLOCK:EDGE, TRIGGER:A:SETHOLD:CLOCK:SOURCE, TRIGGER:A:SETHOLD:CLOCK:THRESHOLD, TRIGGER:A:SETHOLD:DATA:SOURCE.

TriggerALogicFunction ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:FUNCtion command.

Description

This command sets or queries the logical combination of the input channels for logic triggers. This command is equivalent to selecting Logic for the Trigger Type, and setting or viewing the Define Logic.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:FUNCtion? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:FUNCtion? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:FUNCtion value command.

SCPI Syntax

- TRIGger:A:LOGIc:FUNCtion {AND|NANd|NOR|OR}
- TRIGger:A:LOGIc:FUNCtion?

Info

AND specifies to trigger if all conditions are true.
NANd specifies to trigger if any of the conditions are false.
NOR specifies to trigger if all conditions are false.
OR specifies to trigger if any of the conditions are true.

TriggerALogicInput ¶

Bases: SCPICmdRead

The TRIGger:A:LOGIc:INPut command.

Description

Returns the logic input values for all channels. If a clock channel is defined, it returns the clock source and edge.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:LOGIc:INPut?

Properties

.ch: The TRIGger:A:LOGIc:INPut:CH<x> command.
.clock: The TRIGger:A:LOGIc:INPut:CLOCk command tree.
.d: The TRIGger:A:LOGIc:INPut:D<x> command.
.rf: The TRIGger:A:LOGIc:INPut:RF command.

ch `property` ¶

ch: dict[int, TriggerALogicInputChannel]

Return the TRIGger:A:LOGIc:INPut:CH<x> command.

Description

This command specifies the logical input condition for the channel specified by .

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:CH<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:CH<x> {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:CH<x>?

Info

HIGH specifies the logic high.
LOW specifies the logic low.
X specifies a ‘don’t care’ state.

clock `property` ¶

clock: TriggerALogicInputClock

Return the TRIGger:A:LOGIc:INPut:CLOCk command tree.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CLOCk? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.edge: The TRIGger:A:LOGIc:INPut:CLOCk:EDGE command.
.source: The TRIGger:A:LOGIc:INPut:CLOCk:SOUrce command.

d `property` ¶

d: dict[int, TriggerALogicInputDigitalBit]

Return the TRIGger:A:LOGIc:INPut:D<x> command.

Description

This command specifies the logic pattern for a trigger on digital channel , where x is the channel number.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:D<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:D<x> {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:D<x>?

Info

High specifies the logic high state.
Low specifies the logic low state.
X specifies a ‘don’t care’ state.

rf `property` ¶

rf: TriggerALogicInputRf

Return the TRIGger:A:LOGIc:INPut:RF command.

Description

This command specifies the logic level to use when the internal RF power level is the source for a logic pattern trigger.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:RF? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:RF value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:RF {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:RF?

Info

HIGH specifies to trigger on a high logic level.
LOW specifies to trigger on a low logic level.
X specifies a ‘don’t care’ condition.

TriggerALogicInputChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:INPut:CH<x> command.

Description

This command specifies the logical input condition for the channel specified by .

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:CH<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:CH<x> {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:CH<x>?

Info

HIGH specifies the logic high.
LOW specifies the logic low.
X specifies a ‘don’t care’ state.

TriggerALogicInputClock ¶

Bases: SCPICmdRead

The TRIGger:A:LOGIc:INPut:CLOCk command tree.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CLOCk? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk? query and raise an AssertionError if the returned value does not match value.

Properties

.edge: The TRIGger:A:LOGIc:INPut:CLOCk:EDGE command.
.source: The TRIGger:A:LOGIc:INPut:CLOCk:SOUrce command.

edge `property` ¶

edge: TriggerALogicInputClockEdge

Return the TRIGger:A:LOGIc:INPut:CLOCk:EDGE command.

Description

Sets the polarity of the clock channel.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CLOCk:EDGE? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:EDGE value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:CLOCk:EDGE {FALL|RISe}
- TRIGger:A:LOGIc:INPut:CLOCk:EDGE?

Info

RISe specifies to trigger on the rising or positive edge of a signal.
FALL specifies to trigger on the falling or negative edge of a signal.

source `property` ¶

source: TriggerALogicInputClockSource

Return the TRIGger:A:LOGIc:INPut:CLOCk:SOUrce command.

Description

This command specifies the channel to use as the clock source. The clock can be selected as NONE. A selection of None implies pattern trigger. Any other selection implies state trigger.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CLOCk:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:SOUrce value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:CLOCk:SOUrce {CH<x>|D<x>|RF|NONE}
- TRIGger:A:LOGIc:INPut:CLOCk:SOUrce?

Info

CH<x> specifies an analog channel as the clock source.
D<x> specifies a digital channel as the clock source. (Requires option 3-MSO.).
NONE specifies a Pattern trigger.

TriggerALogicInputClockEdge ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:INPut:CLOCk:EDGE command.

Description

Sets the polarity of the clock channel.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CLOCk:EDGE? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:EDGE value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:CLOCk:EDGE {FALL|RISe}
- TRIGger:A:LOGIc:INPut:CLOCk:EDGE?

Info

RISe specifies to trigger on the rising or positive edge of a signal.
FALL specifies to trigger on the falling or negative edge of a signal.

TriggerALogicInputClockSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:INPut:CLOCk:SOUrce command.

Description

This command specifies the channel to use as the clock source. The clock can be selected as NONE. A selection of None implies pattern trigger. Any other selection implies state trigger.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:CLOCk:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:CLOCk:SOUrce value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:CLOCk:SOUrce {CH<x>|D<x>|RF|NONE}
- TRIGger:A:LOGIc:INPut:CLOCk:SOUrce?

Info

CH<x> specifies an analog channel as the clock source.
D<x> specifies a digital channel as the clock source. (Requires option 3-MSO.).
NONE specifies a Pattern trigger.

TriggerALogicInputDigitalBit ¶

Bases: ValidatedDigitalBit, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:INPut:D<x> command.

Description

This command specifies the logic pattern for a trigger on digital channel , where x is the channel number.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:D<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:D<x> {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:D<x>?

Info

High specifies the logic high state.
Low specifies the logic low state.
X specifies a ‘don’t care’ state.

TriggerALogicInputRf ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:INPut:RF command.

Description

This command specifies the logic level to use when the internal RF power level is the source for a logic pattern trigger.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:INPut:RF? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:INPut:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:INPut:RF value command.

SCPI Syntax

- TRIGger:A:LOGIc:INPut:RF {HIGH|LOW|X}
- TRIGger:A:LOGIc:INPut:RF?

Info

HIGH specifies to trigger on a high logic level.
LOW specifies to trigger on a low logic level.
X specifies a ‘don’t care’ condition.

TriggerALogicPattern ¶

Bases: SCPICmdRead

The TRIGger:A:LOGIc:PATtern command.

Description

Returns the conditions used for generating an A logic pattern trigger, with respect to the defined input pattern, and identifies the time that the selected pattern may be true and still generate the trigger.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:PATtern? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:PATtern? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:LOGIc:PATtern?

Properties

.deltatime: The TRIGger:A:LOGIc:PATtern:DELTatime command.
.when: The TRIGger:A:LOGIc:PATtern:WHEn command.

deltatime `property` ¶

deltatime: TriggerALogicPatternDeltatime

Return the TRIGger:A:LOGIc:PATtern:DELTatime command.

Description

This command specifies the pattern trigger delta time value. The time value is used as part of the pattern trigger condition to determine if the duration of a logic pattern meets the specified time constraints.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:PATtern:DELTatime? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:PATtern:DELTatime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:PATtern:DELTatime value command.

SCPI Syntax

- TRIGger:A:LOGIc:PATtern:DELTatime <NR3>
- TRIGger:A:LOGIc:PATtern:DELTatime?

Info

<NR3> is a floating point value with exponent that sets the pattern trigger time value. This argument has a range of 39.6E-9 (39.6 ns) to 10.0E0 (10 s), in increments of 13.2 ns. Values that are not an increment of 13.2 ns are rounded to the nearest correct value.

when `property` ¶

when: TriggerALogicPatternWhen

Return the TRIGger:A:LOGIc:PATtern:WHEn command.

Description

This command specifies the pattern logic condition on which to trigger the oscilloscope.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:PATtern:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:PATtern:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:PATtern:WHEn value command.

SCPI Syntax

- TRIGger:A:LOGIc:PATtern:WHEn {TRUe|FALSe|LESSthan|MOREthan|EQual|UNEQual}
- TRIGger:A:LOGIc:PATtern:WHEn?

Info

TRUE triggers the oscilloscope when the pattern becomes true.
FALSE triggers the oscilloscope when the pattern becomes false.
LESSTHAN triggers the oscilloscope when the input pattern is true for a time period less than the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME.
MORETHAN triggers the oscilloscope when the input pattern is true for a time period more (greater) than the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME.
EQUAL triggers the oscilloscope when the input pattern is true for a time period equal to the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME, within a ±5% tolerance.
UNEQUAL triggers the oscilloscope when the input pattern is true for a time period greater than or less than (not equal to) the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME, within a ±5% tolerance.

TriggerALogicPatternDeltatime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:PATtern:DELTatime command.

Description

This command specifies the pattern trigger delta time value. The time value is used as part of the pattern trigger condition to determine if the duration of a logic pattern meets the specified time constraints.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:PATtern:DELTatime? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:PATtern:DELTatime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:PATtern:DELTatime value command.

SCPI Syntax

- TRIGger:A:LOGIc:PATtern:DELTatime <NR3>
- TRIGger:A:LOGIc:PATtern:DELTatime?

Info

<NR3> is a floating point value with exponent that sets the pattern trigger time value. This argument has a range of 39.6E-9 (39.6 ns) to 10.0E0 (10 s), in increments of 13.2 ns. Values that are not an increment of 13.2 ns are rounded to the nearest correct value.

TriggerALogicPatternWhen ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:PATtern:WHEn command.

Description

This command specifies the pattern logic condition on which to trigger the oscilloscope.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:PATtern:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:PATtern:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:PATtern:WHEn value command.

SCPI Syntax

- TRIGger:A:LOGIc:PATtern:WHEn {TRUe|FALSe|LESSthan|MOREthan|EQual|UNEQual}
- TRIGger:A:LOGIc:PATtern:WHEn?

Info

TRUE triggers the oscilloscope when the pattern becomes true.
FALSE triggers the oscilloscope when the pattern becomes false.
LESSTHAN triggers the oscilloscope when the input pattern is true for a time period less than the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME.
MORETHAN triggers the oscilloscope when the input pattern is true for a time period more (greater) than the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME.
EQUAL triggers the oscilloscope when the input pattern is true for a time period equal to the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME, within a ±5% tolerance.
UNEQUAL triggers the oscilloscope when the input pattern is true for a time period greater than or less than (not equal to) the time period specified in TRIGGER:A:LOGIC:PATTERN:DELTATIME, within a ±5% tolerance.

TriggerALogicThreshold ¶

Bases: SCPICmdRead

The TRIGger:A:LOGIc:THReshold command tree.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold? query and raise an AssertionError if the returned value does not match value.

Properties

.ch: The TRIGger:A:LOGIc:THReshold:CH<x> command.
.d: The TRIGger:A:LOGIc:THReshold:D<x> command.
.rf: The TRIGger:A:LOGIc:THReshold:RF command.

ch `property` ¶

ch: dict[int, TriggerALogicThresholdChannel]

Return the TRIGger:A:LOGIc:THReshold:CH<x> command.

Description

This command sets or queries the trigger A logic threshold voltage for the specified channel x.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:THReshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:THReshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOGIc:THReshold:CH<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

d `property` ¶

d: dict[int, TriggerALogicThresholdDigitalBit]

Return the TRIGger:A:LOGIc:THReshold:D<x> command.

Description

This command specifies the trigger A logic threshold level for the specified digital channel . This commands affects all trigger types using the digital channel.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:THReshold:D<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:THReshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOGIc:THReshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold level in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

rf `property` ¶

rf: TriggerALogicThresholdRf

Return the TRIGger:A:LOGIc:THReshold:RF command.

Description

This command specifies the threshold to use when the internal RF power level is the source for a logic trigger. It will affect all trigger types using the channel.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold:RF? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:THReshold:RF value command.

SCPI Syntax

- TRIGger:A:LOGIc:THReshold:RF {<NR3>}
- TRIGger:A:LOGIc:THReshold:RF?

Info

<NR3> is a floating point number that specifies the threshold to use, in the currently selected RF units (using RF:UNITS). The range is (ref level - 40 dBm) to (ref level + 10 dBm), but never less than -65 dBm or more than +30 dBm.

TriggerALogicThresholdChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:THReshold:CH<x> command.

Description

This command sets or queries the trigger A logic threshold voltage for the specified channel x.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:THReshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:THReshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOGIc:THReshold:CH<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerALogicThresholdDigitalBit ¶

Bases: ValidatedDigitalBit, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:THReshold:D<x> command.

Description

This command specifies the trigger A logic threshold level for the specified digital channel . This commands affects all trigger types using the digital channel.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:THReshold:D<x> value command.

SCPI Syntax

- TRIGger:A:LOGIc:THReshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOGIc:THReshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold level in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerALogicThresholdRf ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOGIc:THReshold:RF command.

Description

This command specifies the threshold to use when the internal RF power level is the source for a logic trigger. It will affect all trigger types using the channel.

Usage

Using the .query() method will send the TRIGger:A:LOGIc:THReshold:RF? query.
Using the .verify(value) method will send the TRIGger:A:LOGIc:THReshold:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOGIc:THReshold:RF value command.

SCPI Syntax

- TRIGger:A:LOGIc:THReshold:RF {<NR3>}
- TRIGger:A:LOGIc:THReshold:RF?

Info

<NR3> is a floating point number that specifies the threshold to use, in the currently selected RF units (using RF:UNITS). The range is (ref level - 40 dBm) to (ref level + 10 dBm), but never less than -65 dBm or more than +30 dBm.

TriggerALowerthreshold ¶

Bases: SCPICmdRead

The TRIGger:A:LOWerthreshold command tree.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold? query and raise an AssertionError if the returned value does not match value.

Properties

.ch: The TRIGger:A:LOWerthreshold:CH<x> command.
.d: The TRIGger:A:LOWerthreshold:D<x> command.
.rf: The TRIGger:A:LOWerthreshold:RF command.
.aux: The TRIGger:A:LOWerthreshold:AUX command.
.ext: The TRIGger:A:LOWerthreshold:EXT command.

aux `property` ¶

aux: TriggerALowerthresholdAux

Return the TRIGger:A:LOWerthreshold:AUX command.

Description

This command specifies the lower threshold for the Aux Input connector. Used for the following trigger types: runt, transition.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:AUX? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:AUX? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:AUX value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:AUX {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:AUX?

Info

<NR3> is a floating point number that specifies the threshold level in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

ch `property` ¶

ch: dict[int, TriggerALowerthresholdChannel]

Return the TRIGger:A:LOWerthreshold:CH<x> command.

Description

This command specifies the lower threshold for the channel selected. Each channel can have an independent level. Used in runt and transition triggers as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:CH<x> {ECL|TTL|<NR3>}
- TRIGger:A:LOWerthreshold:CH<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the clock level, in volts.

d `property` ¶

d: dict[int, TriggerALowerthresholdDigitalBit]

Return the TRIGger:A:LOWerthreshold:D<x> command.

Description

Sets the lower threshold for the digital channel selected. Each channel can have an independent level. Used in runt and transition as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:D<x> value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

ext `property` ¶

ext: TriggerALowerthresholdExt

Return the TRIGger:A:LOWerthreshold:EXT command.

Description

This command specifies the lower threshold for the Aux Input connector. Used for the following trigger types: runt, transition.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:EXT? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:EXT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:EXT value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:EXT {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:EXT?

Info

<NR3> is a floating point number that specifies the threshold level in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

rf `property` ¶

rf: TriggerALowerthresholdRf

Return the TRIGger:A:LOWerthreshold:RF command.

Description

This command specifies the lower threshold when using the internal RF power level for a RUNT trigger, or the single threshold in the cases of the PULSE and TIMEOUT triggers. To specify the upper threshold for the internal RF power level for the RUNT trigger type, use the command TRIGGER:A:UPPERTHRESHOLD:RF. To choose the RUNT trigger type, use the command TRIGGER:A:PULSE:CLASS.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:RF? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:RF value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:RF {<NR3>}
- TRIGger:A:LOWerthreshold:RF?

Info

<NR3> is a floating point number that specifies the threshold to use, in the currently selected RF units (using RF:UNITS). The range is (ref level - 40 dBm) to (ref level + 10 dBm), but never less than -65 dBm or more than +30 dBm.

TriggerALowerthresholdAux ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOWerthreshold:AUX command.

Description

This command specifies the lower threshold for the Aux Input connector. Used for the following trigger types: runt, transition.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:AUX? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:AUX? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:AUX value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:AUX {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:AUX?

Info

<NR3> is a floating point number that specifies the threshold level in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerALowerthresholdChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOWerthreshold:CH<x> command.

Description

This command specifies the lower threshold for the channel selected. Each channel can have an independent level. Used in runt and transition triggers as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:CH<x> {ECL|TTL|<NR3>}
- TRIGger:A:LOWerthreshold:CH<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the clock level, in volts.

TriggerALowerthresholdDigitalBit ¶

Bases: ValidatedDigitalBit, SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOWerthreshold:D<x> command.

Description

Sets the lower threshold for the digital channel selected. Each channel can have an independent level. Used in runt and transition as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:D<x> value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerALowerthresholdExt ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOWerthreshold:EXT command.

Description

This command specifies the lower threshold for the Aux Input connector. Used for the following trigger types: runt, transition.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:EXT? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:EXT? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:EXT value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:EXT {<NR3>|ECL|TTL}
- TRIGger:A:LOWerthreshold:EXT?

Info

<NR3> is a floating point number that specifies the threshold level in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerALowerthresholdRf ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:LOWerthreshold:RF command.

Description

This command specifies the lower threshold when using the internal RF power level for a RUNT trigger, or the single threshold in the cases of the PULSE and TIMEOUT triggers. To specify the upper threshold for the internal RF power level for the RUNT trigger type, use the command TRIGGER:A:UPPERTHRESHOLD:RF. To choose the RUNT trigger type, use the command TRIGGER:A:PULSE:CLASS.

Usage

Using the .query() method will send the TRIGger:A:LOWerthreshold:RF? query.
Using the .verify(value) method will send the TRIGger:A:LOWerthreshold:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:LOWerthreshold:RF value command.

SCPI Syntax

- TRIGger:A:LOWerthreshold:RF {<NR3>}
- TRIGger:A:LOWerthreshold:RF?

Info

<NR3> is a floating point number that specifies the threshold to use, in the currently selected RF units (using RF:UNITS). The range is (ref level - 40 dBm) to (ref level + 10 dBm), but never less than -65 dBm or more than +30 dBm.

TriggerAMode ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:MODe command.

Description

This command sets or queries the A trigger mode. This command is equivalent to pushing the Mode button on the front panel.

Usage

Using the .query() method will send the TRIGger:A:MODe? query.
Using the .verify(value) method will send the TRIGger:A:MODe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:MODe value command.

SCPI Syntax

- TRIGger:A:MODe {AUTO|NORMal}
- TRIGger:A:MODe?

Info

AUTO generates a trigger if one is not detected within a specified time period.
NORMal waits for a valid trigger event.

TriggerAPulse ¶

Bases: SCPICmdRead

The TRIGger:A:PULse command tree.

Usage

Using the .query() method will send the TRIGger:A:PULse? query.
Using the .verify(value) method will send the TRIGger:A:PULse? query and raise an AssertionError if the returned value does not match value.

Properties

.class: The TRIGger:A:PULse:CLAss command.

class_ `property` ¶

class_: TriggerAPulseClass

Return the TRIGger:A:PULse:CLAss command.

Description

This command specifies which kind of pulse to trigger on (either runt, width, transition (rise/fall or slew rate) or timeout). You also need to set the trigger type to PULSe using the command TRIGGER:A:TYPE. To set the trigger source for a pulse trigger, use TRIGGER:A:RUNT:SOURCE, TRIGGER:A:PULSEWIDTH:SOURCE, , or TRIGGER:A:TIMEOUT:SOURCE. To set the trigger voltage threshold level for a pulse trigger, use TRIGGER:A:LEVEL:AUXIN, TRIGGER:A:LEVEL:CHX, or TRIGGER:A:LEVEL:DX.

Usage

Using the .query() method will send the TRIGger:A:PULse:CLAss? query.
Using the .verify(value) method will send the TRIGger:A:PULse:CLAss? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULse:CLAss value command.

SCPI Syntax

- TRIGger:A:PULse:CLAss {RUNt|WIDth|TRANsition|TIMEOut}
- TRIGger:A:PULse:CLAss?

Info

RUNt triggers when a pulse crosses the first preset voltage threshold but does not cross the second preset threshold before recrossing the first. Use with the command TRIGGER:A:RUNT:SOURCE, TRIGGER:A:RUNT:POLARITY, TRIGGER:A:RUNT:WHEN, and TRIGGER:A:RUNT:WIDTH.
WIDth triggers when a pulse is found that has the specified width or duration and is either inside or outside the specified time limits. Use with the commands TRIGGER:A:PULSEWIDTH:HIGHLIMIT, TRIGGER:A:PULSEWIDTH:LOWLIMIT, TRIGGER:A:PULSEWIDTH:POLARITY, TRIGGER:A:PULSEWIDTH:SOURCE, TRIGGER:A:PULSEWIDTH:WHEN, and TRIGGER:A:PULSEWIDTH:WIDTH.
TRANsition (AKA rise/fall or slew rate) triggers when a pulse crosses both thresholds in the same direction as the specified polarity and the transition time between the two threshold crossings is greater or less than the specified time delta. Use with the commands.
TIMEout triggers when no pulse is detected within a specified time. The signal stays above, below, or either above or below, a set value for a set amount of time. Use with the commands TRIGGER:A:TIMEOUT:TIME, TRIGGER:A:TIMEOUT:POLARITY, TRIGGER:A:TIMEOUT:SOURCE.

TriggerAPulseClass ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:PULse:CLAss command.

Description

This command specifies which kind of pulse to trigger on (either runt, width, transition (rise/fall or slew rate) or timeout). You also need to set the trigger type to PULSe using the command TRIGGER:A:TYPE. To set the trigger source for a pulse trigger, use TRIGGER:A:RUNT:SOURCE, TRIGGER:A:PULSEWIDTH:SOURCE, , or TRIGGER:A:TIMEOUT:SOURCE. To set the trigger voltage threshold level for a pulse trigger, use TRIGGER:A:LEVEL:AUXIN, TRIGGER:A:LEVEL:CHX, or TRIGGER:A:LEVEL:DX.

Usage

Using the .query() method will send the TRIGger:A:PULse:CLAss? query.
Using the .verify(value) method will send the TRIGger:A:PULse:CLAss? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULse:CLAss value command.

SCPI Syntax

- TRIGger:A:PULse:CLAss {RUNt|WIDth|TRANsition|TIMEOut}
- TRIGger:A:PULse:CLAss?

Info

RUNt triggers when a pulse crosses the first preset voltage threshold but does not cross the second preset threshold before recrossing the first. Use with the command TRIGGER:A:RUNT:SOURCE, TRIGGER:A:RUNT:POLARITY, TRIGGER:A:RUNT:WHEN, and TRIGGER:A:RUNT:WIDTH.
WIDth triggers when a pulse is found that has the specified width or duration and is either inside or outside the specified time limits. Use with the commands TRIGGER:A:PULSEWIDTH:HIGHLIMIT, TRIGGER:A:PULSEWIDTH:LOWLIMIT, TRIGGER:A:PULSEWIDTH:POLARITY, TRIGGER:A:PULSEWIDTH:SOURCE, TRIGGER:A:PULSEWIDTH:WHEN, and TRIGGER:A:PULSEWIDTH:WIDTH.
TRANsition (AKA rise/fall or slew rate) triggers when a pulse crosses both thresholds in the same direction as the specified polarity and the transition time between the two threshold crossings is greater or less than the specified time delta. Use with the commands.
TIMEout triggers when no pulse is detected within a specified time. The signal stays above, below, or either above or below, a set value for a set amount of time. Use with the commands TRIGGER:A:TIMEOUT:TIME, TRIGGER:A:TIMEOUT:POLARITY, TRIGGER:A:TIMEOUT:SOURCE.

TriggerAPulsewidth ¶

Bases: SCPICmdRead

The TRIGger:A:PULSEWidth command tree.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth? query and raise an AssertionError if the returned value does not match value.

Properties

.highlimit: The TRIGger:A:PULSEWidth:HIGHLimit command.
.lowlimit: The TRIGger:A:PULSEWidth:LOWLimit command.
.polarity: The TRIGger:A:PULSEWidth:POLarity command.
.source: The TRIGger:A:PULSEWidth:SOUrce command.
.when: The TRIGger:A:PULSEWidth:WHEn command.
.width: The TRIGger:A:PULSEWidth:WIDth command.

highlimit `property` ¶

highlimit: TriggerAPulsewidthHighlimit

Return the TRIGger:A:PULSEWidth:HIGHLimit command.

Description

This command specifies the upper limit to use, in seconds, when triggering on detection of a pulse whose duration is inside or outside a range of two values. (Use TRIGGER:A:PULSEWIDTH:LOWLIMIT to specify the lower value of the range.)

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:HIGHLimit? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:HIGHLimit value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:HIGHLimit <NR3>
- TRIGger:A:PULSEWidth:HIGHLimit?

Info

<NR3> is a floating point number that represents the higher value of the range.

lowlimit `property` ¶

lowlimit: TriggerAPulsewidthLowlimit

Return the TRIGger:A:PULSEWidth:LOWLimit command.

Description

This command specifies the lower limit to use, in seconds, when triggering on detection of a pulse whose duration is inside or outside a range of two values. (Use TRIGGER:A:PULSEWIDTH:HIGHLIMIT to specify the upper limit of the range.) This command also specifies the single limit to use, in seconds, when triggering on detection of a pulse whose duration is less than, greater than, equal to, or not equal to this time limit.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:LOWLimit? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:LOWLimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:LOWLimit value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:LOWLimit <NR3>
- TRIGger:A:PULSEWidth:LOWLimit?

Info

<NR3> is a floating point number that represents the lower value of the range.

polarity `property` ¶

polarity: TriggerAPulsewidthPolarity

Return the TRIGger:A:PULSEWidth:POLarity command.

Description

This command specifies the polarity for a pulse width trigger.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:POLarity value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:POLarity {NEGative|POSitive}
- TRIGger:A:PULSEWidth:POLarity?

Info

NEGative specifies a negative pulse.
POSitive specifies a positive pulse.

source `property` ¶

source: TriggerAPulsewidthSource

Return the TRIGger:A:PULSEWidth:SOUrce command.

Description

This command specifies the source waveform for a pulse width trigger.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:SOUrce value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:SOUrce {CH<x>|LINE|AUX|D<x>|RF}
- TRIGger:A:PULSEWidth:SOUrce?

Info

CH<x> specifies an analog input channel as the pulse-width trigger source.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (Only for 2-channel model MDO32.).
LINE specifies AC line voltage as the trigger source.
D<x> specifies a digital channel as the trigger source.

when `property` ¶

when: TriggerAPulsewidthWhen

Return the TRIGger:A:PULSEWidth:WHEn command.

Description

This command specifies to trigger when a pulse is detected with a width (duration) that is less than, greater than, equal to, or unequal to a specified value (set using TRIGGER:A:PULSEWIDTH:LOWLIMIT), OR whose width falls outside of or within a specified range of two values (set using TRIGGER:A:PULSEWIDTH:LOWLIMIT and TRIGGER:A:PULSEWIDTH:HIGHLIMIT).

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:WHEn value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:WHEn {LESSthan|MOREthan|EQual|UNEQual|WIThin|OUTside}
- TRIGger:A:PULSEWidth:WHEn?

Info

LESSthan causes a trigger when a pulse is detected with a width less than the time set by the TRIGGER:A:PULSEWIDTH:LOWLIMIT command.
MOREthan causes a trigger when a pulse is detected with a width greater than the time set by the TRIGGER:A:PULSEWIDTH:LOWLIMIT command.
EQual causes a trigger when a pulse is detected with a width equal to the time period specified in TRIGGER:A:PULSEWIDTH:LOWLIMIT within a ±5% tolerance.
UNEQual causes a trigger when a pulse is detected with a width greater than or less than (but not equal) the time period specified in TRIGGER:A:PULSEWIDTH:LOWLIMIT within a ±5% tolerance.
WIThin causes a trigger when a pulse is detected that is within a range set by two values.
OUTside causes a trigger when a pulse is detected that is outside of a range set by two values.

width `property` ¶

width: TriggerAPulsewidthWidth

Return the TRIGger:A:PULSEWidth:WIDth command.

Description

This command specifies the pulse width (duration), in seconds, for triggering on pulses whose widths are greater than, less than, equal to, or not equal to the specified value.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:WIDth? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:WIDth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:WIDth value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:WIDth <NR3>
- TRIGger:A:PULSEWidth:WIDth?

Info

<NR3> is a floating point number that specifies the pulse width in seconds.

TriggerAPulsewidthHighlimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:PULSEWidth:HIGHLimit command.

Description

This command specifies the upper limit to use, in seconds, when triggering on detection of a pulse whose duration is inside or outside a range of two values. (Use TRIGGER:A:PULSEWIDTH:LOWLIMIT to specify the lower value of the range.)

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:HIGHLimit? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:HIGHLimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:HIGHLimit value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:HIGHLimit <NR3>
- TRIGger:A:PULSEWidth:HIGHLimit?

Info

<NR3> is a floating point number that represents the higher value of the range.

TriggerAPulsewidthLowlimit ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:PULSEWidth:LOWLimit command.

Description

This command specifies the lower limit to use, in seconds, when triggering on detection of a pulse whose duration is inside or outside a range of two values. (Use TRIGGER:A:PULSEWIDTH:HIGHLIMIT to specify the upper limit of the range.) This command also specifies the single limit to use, in seconds, when triggering on detection of a pulse whose duration is less than, greater than, equal to, or not equal to this time limit.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:LOWLimit? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:LOWLimit? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:LOWLimit value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:LOWLimit <NR3>
- TRIGger:A:PULSEWidth:LOWLimit?

Info

<NR3> is a floating point number that represents the lower value of the range.

TriggerAPulsewidthPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:PULSEWidth:POLarity command.

Description

This command specifies the polarity for a pulse width trigger.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:POLarity value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:POLarity {NEGative|POSitive}
- TRIGger:A:PULSEWidth:POLarity?

Info

NEGative specifies a negative pulse.
POSitive specifies a positive pulse.

TriggerAPulsewidthSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:PULSEWidth:SOUrce command.

Description

This command specifies the source waveform for a pulse width trigger.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:SOUrce value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:SOUrce {CH<x>|LINE|AUX|D<x>|RF}
- TRIGger:A:PULSEWidth:SOUrce?

Info

CH<x> specifies an analog input channel as the pulse-width trigger source.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (Only for 2-channel model MDO32.).
LINE specifies AC line voltage as the trigger source.
D<x> specifies a digital channel as the trigger source.

TriggerAPulsewidthWhen ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:PULSEWidth:WHEn command.

Description

This command specifies to trigger when a pulse is detected with a width (duration) that is less than, greater than, equal to, or unequal to a specified value (set using TRIGGER:A:PULSEWIDTH:LOWLIMIT), OR whose width falls outside of or within a specified range of two values (set using TRIGGER:A:PULSEWIDTH:LOWLIMIT and TRIGGER:A:PULSEWIDTH:HIGHLIMIT).

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:WHEn value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:WHEn {LESSthan|MOREthan|EQual|UNEQual|WIThin|OUTside}
- TRIGger:A:PULSEWidth:WHEn?

Info

LESSthan causes a trigger when a pulse is detected with a width less than the time set by the TRIGGER:A:PULSEWIDTH:LOWLIMIT command.
MOREthan causes a trigger when a pulse is detected with a width greater than the time set by the TRIGGER:A:PULSEWIDTH:LOWLIMIT command.
EQual causes a trigger when a pulse is detected with a width equal to the time period specified in TRIGGER:A:PULSEWIDTH:LOWLIMIT within a ±5% tolerance.
UNEQual causes a trigger when a pulse is detected with a width greater than or less than (but not equal) the time period specified in TRIGGER:A:PULSEWIDTH:LOWLIMIT within a ±5% tolerance.
WIThin causes a trigger when a pulse is detected that is within a range set by two values.
OUTside causes a trigger when a pulse is detected that is outside of a range set by two values.

TriggerAPulsewidthWidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:PULSEWidth:WIDth command.

Description

This command specifies the pulse width (duration), in seconds, for triggering on pulses whose widths are greater than, less than, equal to, or not equal to the specified value.

Usage

Using the .query() method will send the TRIGger:A:PULSEWidth:WIDth? query.
Using the .verify(value) method will send the TRIGger:A:PULSEWidth:WIDth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:PULSEWidth:WIDth value command.

SCPI Syntax

- TRIGger:A:PULSEWidth:WIDth <NR3>
- TRIGger:A:PULSEWidth:WIDth?

Info

<NR3> is a floating point number that specifies the pulse width in seconds.

TriggerARisefall ¶

Bases: SCPICmdRead

The TRIGger:A:RISEFall command.

Description

Returns transition time trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:RISEFall? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:RISEFall?

Properties

.deltatime: The TRIGger:A:RISEFall:DELTatime command.
.polarity: The TRIGger:A:RISEFall:POLarity command.
.source: The TRIGger:A:RISEFall:SOUrce command.
.when: The TRIGger:A:RISEFall:WHEn command.

deltatime `property` ¶

deltatime: TriggerARisefallDeltatime

Return the TRIGger:A:RISEFall:DELTatime command.

Description

This command specifies the delta time used in calculating the transition value for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:DELTatime? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:DELTatime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:DELTatime value command.

SCPI Syntax

- TRIGger:A:RISEFall:DELTatime <NR3>
- TRIGger:A:RISEFall:DELTatime?

Info

<NR3> is a floating point number that specifies the delta time, in seconds.

polarity `property` ¶

polarity: TriggerARisefallPolarity

Return the TRIGger:A:RISEFall:POLarity command.

Description

This command specifies the polarity for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:POLarity value command.

SCPI Syntax

- TRIGger:A:RISEFall:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:RISEFall:POLarity?

Info

POSitive indicates that a pulse edge must traverse from the lower (most negative) to higher (most positive) level for transition triggering to occur.
NEGative indicates that a pulse edge must traverse from the upper (most positive) to lower (most negative) level for transition triggering to occur.
EITher indicates either positive or negative polarity.

source `property` ¶

source: TriggerARisefallSource

Return the TRIGger:A:RISEFall:SOUrce command.

Description

This command specifies the source for a transition trigger.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:SOUrce value command.

SCPI Syntax

- TRIGger:A:RISEFall:SOUrce {CH<x>}
- TRIGger:A:RISEFall:SOUrce?

Info

CH<x> specifies one of the analog channels to be used as the source for a transition trigger.

when `property` ¶

when: TriggerARisefallWhen

Return the TRIGger:A:RISEFall:WHEn command.

Description

This command specifies whether to check for a transitioning signal that is faster or slower than the specified delta time.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:WHEn value command.

SCPI Syntax

- TRIGger:A:RISEFall:WHEn {SLOWer|FASTer|EQual|UNEQual}
- TRIGger:A:RISEFall:WHEn?

Info

FASTer sets the trigger to occur when the signal transition time is faster than the time set by TRIGger:A:TRANsition:DELTatime.
SLOWer sets the trigger to occur when the signal transition time is slower than the time set by.TRIGger:A:TRANsition:DELTatime.
EQual sets the trigger to occur when the signal transition time is equal to the time set by TRIGger:A:TRANsition:DELTatime.
UNEQual sets the trigger to occur when the signal transition time is not equal to the time set by TRIGger:A:TRANsition:DELTatime.

TriggerARisefallDeltatime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RISEFall:DELTatime command.

Description

This command specifies the delta time used in calculating the transition value for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:DELTatime? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:DELTatime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:DELTatime value command.

SCPI Syntax

- TRIGger:A:RISEFall:DELTatime <NR3>
- TRIGger:A:RISEFall:DELTatime?

Info

<NR3> is a floating point number that specifies the delta time, in seconds.

TriggerARisefallPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RISEFall:POLarity command.

Description

This command specifies the polarity for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:POLarity value command.

SCPI Syntax

- TRIGger:A:RISEFall:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:RISEFall:POLarity?

Info

POSitive indicates that a pulse edge must traverse from the lower (most negative) to higher (most positive) level for transition triggering to occur.
NEGative indicates that a pulse edge must traverse from the upper (most positive) to lower (most negative) level for transition triggering to occur.
EITher indicates either positive or negative polarity.

TriggerARisefallSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RISEFall:SOUrce command.

Description

This command specifies the source for a transition trigger.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:SOUrce value command.

SCPI Syntax

- TRIGger:A:RISEFall:SOUrce {CH<x>}
- TRIGger:A:RISEFall:SOUrce?

Info

CH<x> specifies one of the analog channels to be used as the source for a transition trigger.

TriggerARisefallWhen ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RISEFall:WHEn command.

Description

This command specifies whether to check for a transitioning signal that is faster or slower than the specified delta time.

Usage

Using the .query() method will send the TRIGger:A:RISEFall:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:RISEFall:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RISEFall:WHEn value command.

SCPI Syntax

- TRIGger:A:RISEFall:WHEn {SLOWer|FASTer|EQual|UNEQual}
- TRIGger:A:RISEFall:WHEn?

Info

FASTer sets the trigger to occur when the signal transition time is faster than the time set by TRIGger:A:TRANsition:DELTatime.
SLOWer sets the trigger to occur when the signal transition time is slower than the time set by.TRIGger:A:TRANsition:DELTatime.
EQual sets the trigger to occur when the signal transition time is equal to the time set by TRIGger:A:TRANsition:DELTatime.
UNEQual sets the trigger to occur when the signal transition time is not equal to the time set by TRIGger:A:TRANsition:DELTatime.

TriggerARunt ¶

Bases: SCPICmdRead

The TRIGger:A:RUNT command.

Description

Returns the current A runt trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:RUNT? query.
Using the .verify(value) method will send the TRIGger:A:RUNT? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:RUNT?

Properties

.polarity: The TRIGger:A:RUNT:POLarity command.
.source: The TRIGger:A:RUNT:SOUrce command.
.when: The TRIGger:A:RUNT:WHEn command.
.width: The TRIGger:A:RUNT:WIDth command.

polarity `property` ¶

polarity: TriggerARuntPolarity

Return the TRIGger:A:RUNT:POLarity command.

Description

This command specifies the polarity for the runt trigger.

Usage

Using the .query() method will send the TRIGger:A:RUNT:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:POLarity value command.

SCPI Syntax

- TRIGger:A:RUNT:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:RUNT:POLarity?

Info

POSitive indicates that the rising edge crosses the low threshold and the falling edge recrosses the low threshold without either edge ever crossing the high threshold.
NEGative indicates that the falling edge crosses the high threshold and the rising edge recrosses the high threshold without either edge ever crossing the low threshold.
EITher triggers on a runt of either polarity.

source `property` ¶

source: TriggerARuntSource

Return the TRIGger:A:RUNT:SOUrce command.

Description

This command specifies the source waveform for the A runt trigger.

Usage

Using the .query() method will send the TRIGger:A:RUNT:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:SOUrce value command.

SCPI Syntax

- TRIGger:A:RUNT:SOUrce {CH<x>|RF}
- TRIGger:A:RUNT:SOUrce?

Info

CH<x> specifies the analog channel number to use as the source waveform for the runt trigger. To specify the threshold levels when using CH1-CH4 as the source, use TRIGGER:A:LOWERTHRESHOLD:CHX and TRIGGER:A:UPPERTHRESHOLD:CHX. x has a minimum of 1 and a maximum of 4.
RF specifies the internal RF power level as the source (MDO4000/B/C models only, and requires installation of an MDO4TRIG application module.) To specify the threshold levels when using RF power level as the source, use TRIGGER:A:LOWERTHRESHOLD:RF and TRIGGER:A:UPPERTHRESHOLD:RF.

when `property` ¶

when: TriggerARuntWhen

Return the TRIGger:A:RUNT:WHEn command.

Description

This command specifies the type of pulse width the trigger checks for when it detects a runt.

Usage

Using the .query() method will send the TRIGger:A:RUNT:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:WHEn value command.

SCPI Syntax

- TRIGger:A:RUNT:WHEn {LESSthan|MOREthan|EQual|UNEQual|OCCURS}
- TRIGger:A:RUNT:WHEn?

Info

OCCURS sets the instrument to trigger if a runt signal of any detectable width occurs.
LESSthan sets the instrument to trigger if the a runt pulse is detected with width less than the time set by the TRIGGER:A:RUNT:WIDTH command.
MOREthan sets the instrument to trigger if the a runt pulse is detected with width greater than the time set by the TRIGGER:A:RUNT:WIDTH command.
EQual sets the instrument to trigger if a runt pulse is detected with width equal to the time period specified in TRIGGER:A:RUNT:WIDTH within a ±5% tolerance.
UNEQual sets the instrument to trigger if a runt pulse is detected with width greater than or less than (but not equal to) the time period specified in TRIGGER:A:RUNT:WIDTH within a ±5% tolerance.

width `property` ¶

width: TriggerARuntWidth

Return the TRIGger:A:RUNT:WIDth command.

Description

This command specifies the width, in seconds, for a runt trigger.

Usage

Using the .query() method will send the TRIGger:A:RUNT:WIDth? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:WIDth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:WIDth value command.

SCPI Syntax

- TRIGger:A:RUNT:WIDth <NR3>
- TRIGger:A:RUNT:WIDth?

Info

<NR3> is a floating point number that specifies the minimum width, in seconds.

TriggerARuntPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RUNT:POLarity command.

Description

This command specifies the polarity for the runt trigger.

Usage

Using the .query() method will send the TRIGger:A:RUNT:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:POLarity value command.

SCPI Syntax

- TRIGger:A:RUNT:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:RUNT:POLarity?

Info

POSitive indicates that the rising edge crosses the low threshold and the falling edge recrosses the low threshold without either edge ever crossing the high threshold.
NEGative indicates that the falling edge crosses the high threshold and the rising edge recrosses the high threshold without either edge ever crossing the low threshold.
EITher triggers on a runt of either polarity.

TriggerARuntSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RUNT:SOUrce command.

Description

This command specifies the source waveform for the A runt trigger.

Usage

Using the .query() method will send the TRIGger:A:RUNT:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:SOUrce value command.

SCPI Syntax

- TRIGger:A:RUNT:SOUrce {CH<x>|RF}
- TRIGger:A:RUNT:SOUrce?

Info

CH<x> specifies the analog channel number to use as the source waveform for the runt trigger. To specify the threshold levels when using CH1-CH4 as the source, use TRIGGER:A:LOWERTHRESHOLD:CHX and TRIGGER:A:UPPERTHRESHOLD:CHX. x has a minimum of 1 and a maximum of 4.
RF specifies the internal RF power level as the source (MDO4000/B/C models only, and requires installation of an MDO4TRIG application module.) To specify the threshold levels when using RF power level as the source, use TRIGGER:A:LOWERTHRESHOLD:RF and TRIGGER:A:UPPERTHRESHOLD:RF.

TriggerARuntWhen ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RUNT:WHEn command.

Description

This command specifies the type of pulse width the trigger checks for when it detects a runt.

Usage

Using the .query() method will send the TRIGger:A:RUNT:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:WHEn value command.

SCPI Syntax

- TRIGger:A:RUNT:WHEn {LESSthan|MOREthan|EQual|UNEQual|OCCURS}
- TRIGger:A:RUNT:WHEn?

Info

OCCURS sets the instrument to trigger if a runt signal of any detectable width occurs.
LESSthan sets the instrument to trigger if the a runt pulse is detected with width less than the time set by the TRIGGER:A:RUNT:WIDTH command.
MOREthan sets the instrument to trigger if the a runt pulse is detected with width greater than the time set by the TRIGGER:A:RUNT:WIDTH command.
EQual sets the instrument to trigger if a runt pulse is detected with width equal to the time period specified in TRIGGER:A:RUNT:WIDTH within a ±5% tolerance.
UNEQual sets the instrument to trigger if a runt pulse is detected with width greater than or less than (but not equal to) the time period specified in TRIGGER:A:RUNT:WIDTH within a ±5% tolerance.

TriggerARuntWidth ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:RUNT:WIDth command.

Description

This command specifies the width, in seconds, for a runt trigger.

Usage

Using the .query() method will send the TRIGger:A:RUNT:WIDth? query.
Using the .verify(value) method will send the TRIGger:A:RUNT:WIDth? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:RUNT:WIDth value command.

SCPI Syntax

- TRIGger:A:RUNT:WIDth <NR3>
- TRIGger:A:RUNT:WIDth?

Info

<NR3> is a floating point number that specifies the minimum width, in seconds.

TriggerASethold ¶

Bases: SCPICmdRead

The TRIGger:A:SETHold command.

Description

Returns the clock edge polarity, voltage threshold and source input; data voltage threshold and source; and both setup and hold times for setup and hold violation triggering.

Usage

Using the .query() method will send the TRIGger:A:SETHold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:SETHold?

Properties

.clock: The TRIGger:A:SETHold:CLOCk command.
.data: The TRIGger:A:SETHold:DATa command.
.holdtime: The TRIGger:A:SETHold:HOLDTime command.
.settime: The TRIGger:A:SETHold:SETTime command.
.threshold: The TRIGger:A:SETHold:THReshold command tree.

clock `property` ¶

clock: TriggerASetholdClock

Return the TRIGger:A:SETHold:CLOCk command.

Description

Returns the clock edge polarity, voltage threshold, and source input for setup and hold triggering.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk?

Sub-properties

.edge: The TRIGger:A:SETHold:CLOCk:EDGE command.
.source: The TRIGger:A:SETHold:CLOCk:SOUrce command.
.threshold: The TRIGger:A:SETHold:CLOCk:THReshold command.

data `property` ¶

data: TriggerASetholdData

Return the TRIGger:A:SETHold:DATa command.

Description

Returns the voltage threshold and data source for the setup and hold trigger.

Usage

Using the .query() method will send the TRIGger:A:SETHold:DATa? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:DATa? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:SETHold:DATa?

Sub-properties

.source: The TRIGger:A:SETHold:DATa:SOUrce command.
.threshold: The TRIGger:A:SETHold:DATa:THReshold command.

holdtime `property` ¶

holdtime: TriggerASetholdHoldtime

Return the TRIGger:A:SETHold:HOLDTime command.

Description

This command specifies the hold time for setup and hold violation triggering. This command is equivalent to selecting Setup/Hold Setup from the Trig menu and then setting the desired Hold Time.

Usage

Using the .query() method will send the TRIGger:A:SETHold:HOLDTime? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:HOLDTime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:HOLDTime value command.

SCPI Syntax

- TRIGger:A:SETHold:HOLDTime <NR3>
- TRIGger:A:SETHold:HOLDTime?

Info

<NR3> is a floating point number that specifies the hold time setting, in seconds. Positive values for hold time occur after the clock edge. Negative values occur before the clock edge.

settime `property` ¶

settime: TriggerASetholdSettime

Return the TRIGger:A:SETHold:SETTime command.

Description

This command specifies the setup time for setup and hold violation triggering. This command is equivalent to selecting Setup/Hold Setup from the Trig menu and then setting the desired Setup Time.

Usage

Using the .query() method will send the TRIGger:A:SETHold:SETTime? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:SETTime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:SETTime value command.

SCPI Syntax

- TRIGger:A:SETHold:SETTime <NR3>
- TRIGger:A:SETHold:SETTime?

Info

<NR3> is a floating point number that specifies the setup time for setup and hold violation triggering.

threshold `property` ¶

threshold: TriggerASetholdThreshold

Return the TRIGger:A:SETHold:THReshold command tree.

Usage

Using the .query() method will send the TRIGger:A:SETHold:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:THReshold? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.ch: The TRIGger:A:SETHold:THReshold:CH<x> command.
.d: The TRIGger:A:SETHold:THReshold:D<x> command.

TriggerASetholdClock ¶

Bases: SCPICmdRead

The TRIGger:A:SETHold:CLOCk command.

Description

Returns the clock edge polarity, voltage threshold, and source input for setup and hold triggering.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk?

Properties

.edge: The TRIGger:A:SETHold:CLOCk:EDGE command.
.source: The TRIGger:A:SETHold:CLOCk:SOUrce command.
.threshold: The TRIGger:A:SETHold:CLOCk:THReshold command.

edge `property` ¶

edge: TriggerASetholdClockEdge

Return the TRIGger:A:SETHold:CLOCk:EDGE command.

Description

This command specifies the clock edge polarity for setup and hold triggering.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk:EDGE? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:CLOCk:EDGE value command.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk:EDGE {FALL|RISe}
- TRIGger:A:SETHold:CLOCk:EDGE?

Info

FALL specifies polarity as the clock falling edge.
RISe specifies polarity as the clock rising edge.

source `property` ¶

source: TriggerASetholdClockSource

Return the TRIGger:A:SETHold:CLOCk:SOUrce command.

Description

This command specifies the clock source for the setup and hold triggering. You cannot specify the same source for both clock and data.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:CLOCk:SOUrce value command.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk:SOUrce {CH<x>|D<x>|AUX}
- TRIGger:A:SETHold:CLOCk:SOUrce?

Info

CH<x> specifies the analog channel to use as the clock source waveform.
D<x> specifies the digital channel to use as the clock source waveform. (Requires option 3-MSO.).
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (Available for 2-channel MDO32, as it has an Aux Input connector.).

threshold `property` ¶

threshold: TriggerASetholdClockThreshold

Return the TRIGger:A:SETHold:CLOCk:THReshold command.

Description

This command specifies the clock voltage threshold for the setup and hold trigger.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk:THReshold? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:CLOCk:THReshold value command.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk:THReshold {<NR3>|TTL}
- TRIGger:A:SETHold:CLOCk:THReshold?

Info

<NR3> is a floating point number that specifies the clock level, in volts.
TTL specifies a preset TTL high level of 1.4 V.

TriggerASetholdClockEdge ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:CLOCk:EDGE command.

Description

This command specifies the clock edge polarity for setup and hold triggering.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk:EDGE? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk:EDGE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:CLOCk:EDGE value command.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk:EDGE {FALL|RISe}
- TRIGger:A:SETHold:CLOCk:EDGE?

Info

FALL specifies polarity as the clock falling edge.
RISe specifies polarity as the clock rising edge.

TriggerASetholdClockSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:CLOCk:SOUrce command.

Description

This command specifies the clock source for the setup and hold triggering. You cannot specify the same source for both clock and data.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:CLOCk:SOUrce value command.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk:SOUrce {CH<x>|D<x>|AUX}
- TRIGger:A:SETHold:CLOCk:SOUrce?

Info

CH<x> specifies the analog channel to use as the clock source waveform.
D<x> specifies the digital channel to use as the clock source waveform. (Requires option 3-MSO.).
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (Available for 2-channel MDO32, as it has an Aux Input connector.).

TriggerASetholdClockThreshold ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:CLOCk:THReshold command.

Description

This command specifies the clock voltage threshold for the setup and hold trigger.

Usage

Using the .query() method will send the TRIGger:A:SETHold:CLOCk:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:CLOCk:THReshold? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:CLOCk:THReshold value command.

SCPI Syntax

- TRIGger:A:SETHold:CLOCk:THReshold {<NR3>|TTL}
- TRIGger:A:SETHold:CLOCk:THReshold?

Info

<NR3> is a floating point number that specifies the clock level, in volts.
TTL specifies a preset TTL high level of 1.4 V.

TriggerASetholdData ¶

Bases: SCPICmdRead

The TRIGger:A:SETHold:DATa command.

Description

Returns the voltage threshold and data source for the setup and hold trigger.

Usage

Using the .query() method will send the TRIGger:A:SETHold:DATa? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:DATa? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:SETHold:DATa?

Properties

.source: The TRIGger:A:SETHold:DATa:SOUrce command.
.threshold: The TRIGger:A:SETHold:DATa:THReshold command.

source `property` ¶

source: TriggerASetholdDataSource

Return the TRIGger:A:SETHold:DATa:SOUrce command.

Description

This command specifies the data source or sources for setup and hold triggering. You can specify any combination of sources as long as none of them are also the clock source. Requires installation of option 3-MSO, which enables you to specify any combination of CH1-CH4 and D0-D15 as the data sources. For 2-channel MDO32, you can also use Aux Input.

Usage

Using the .query() method will send the TRIGger:A:SETHold:DATa:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:DATa:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:DATa:SOUrce value command.

SCPI Syntax

- TRIGger:A:SETHold:DATa:SOUrce {CH<x>|D<x>|AUX}
- TRIGger:A:SETHold:DATa:SOUrce?

Info

CH<x> specifies an analog input channel as the data source for the setup and hold trigger.
D<x> specifies a digital channel as the source. Requires option 3-MSO.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (For 2-channel MDO32 only.).

threshold `property` ¶

threshold: TriggerASetholdDataThreshold

Return the TRIGger:A:SETHold:DATa:THReshold command.

Description

This command specifies the data voltage threshold for setup and hold trigger.

Usage

Using the .query() method will send the TRIGger:A:SETHold:DATa:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:DATa:THReshold? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:DATa:THReshold value command.

SCPI Syntax

- TRIGger:A:SETHold:DATa:THReshold {<NR3>|TTL}
- TRIGger:A:SETHold:DATa:THReshold?

Info

TTL specifies the preset TTL high level of 1.4 V.
<NR3> is a floating point number that specifies the setup and hold data level, in volts.

TriggerASetholdDataSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:DATa:SOUrce command.

Description

This command specifies the data source or sources for setup and hold triggering. You can specify any combination of sources as long as none of them are also the clock source. Requires installation of option 3-MSO, which enables you to specify any combination of CH1-CH4 and D0-D15 as the data sources. For 2-channel MDO32, you can also use Aux Input.

Usage

Using the .query() method will send the TRIGger:A:SETHold:DATa:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:DATa:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:DATa:SOUrce value command.

SCPI Syntax

- TRIGger:A:SETHold:DATa:SOUrce {CH<x>|D<x>|AUX}
- TRIGger:A:SETHold:DATa:SOUrce?

Info

CH<x> specifies an analog input channel as the data source for the setup and hold trigger.
D<x> specifies a digital channel as the source. Requires option 3-MSO.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (For 2-channel MDO32 only.).

TriggerASetholdDataThreshold ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:DATa:THReshold command.

Description

This command specifies the data voltage threshold for setup and hold trigger.

Usage

Using the .query() method will send the TRIGger:A:SETHold:DATa:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:DATa:THReshold? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:DATa:THReshold value command.

SCPI Syntax

- TRIGger:A:SETHold:DATa:THReshold {<NR3>|TTL}
- TRIGger:A:SETHold:DATa:THReshold?

Info

TTL specifies the preset TTL high level of 1.4 V.
<NR3> is a floating point number that specifies the setup and hold data level, in volts.

TriggerASetholdHoldtime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:HOLDTime command.

Description

This command specifies the hold time for setup and hold violation triggering. This command is equivalent to selecting Setup/Hold Setup from the Trig menu and then setting the desired Hold Time.

Usage

Using the .query() method will send the TRIGger:A:SETHold:HOLDTime? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:HOLDTime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:HOLDTime value command.

SCPI Syntax

- TRIGger:A:SETHold:HOLDTime <NR3>
- TRIGger:A:SETHold:HOLDTime?

Info

<NR3> is a floating point number that specifies the hold time setting, in seconds. Positive values for hold time occur after the clock edge. Negative values occur before the clock edge.

TriggerASetholdSettime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:SETTime command.

Description

This command specifies the setup time for setup and hold violation triggering. This command is equivalent to selecting Setup/Hold Setup from the Trig menu and then setting the desired Setup Time.

Usage

Using the .query() method will send the TRIGger:A:SETHold:SETTime? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:SETTime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:SETTime value command.

SCPI Syntax

- TRIGger:A:SETHold:SETTime <NR3>
- TRIGger:A:SETHold:SETTime?

Info

<NR3> is a floating point number that specifies the setup time for setup and hold violation triggering.

TriggerASetholdThreshold ¶

Bases: SCPICmdRead

The TRIGger:A:SETHold:THReshold command tree.

Usage

Using the .query() method will send the TRIGger:A:SETHold:THReshold? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:THReshold? query and raise an AssertionError if the returned value does not match value.

Properties

.ch: The TRIGger:A:SETHold:THReshold:CH<x> command.
.d: The TRIGger:A:SETHold:THReshold:D<x> command.

ch `property` ¶

ch: dict[int, TriggerASetholdThresholdChannel]

Return the TRIGger:A:SETHold:THReshold:CH<x> command.

Description

This command specifies the threshold for the analog channel . x can be 1-4. All trigger types using the channel are affected.

Usage

Using the .query() method will send the TRIGger:A:SETHold:THReshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:THReshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:THReshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:SETHold:THReshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:SETHold:THReshold:CH<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

d `property` ¶

d: dict[int, TriggerASetholdThresholdDigitalBit]

Return the TRIGger:A:SETHold:THReshold:D<x> command.

Description

This command sets the threshold for the specified digital channel. can be D0 - D15. All trigger types using the digital channel are affected.

Usage

Using the .query() method will send the TRIGger:A:SETHold:THReshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:THReshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:THReshold:D<x> value command.

SCPI Syntax

- TRIGger:A:SETHold:THReshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:SETHold:THReshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerASetholdThresholdChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:THReshold:CH<x> command.

Description

This command specifies the threshold for the analog channel . x can be 1-4. All trigger types using the channel are affected.

Usage

Using the .query() method will send the TRIGger:A:SETHold:THReshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:THReshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:THReshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:SETHold:THReshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:SETHold:THReshold:CH<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerASetholdThresholdDigitalBit ¶

Bases: ValidatedDigitalBit, SCPICmdWrite, SCPICmdRead

The TRIGger:A:SETHold:THReshold:D<x> command.

Description

This command sets the threshold for the specified digital channel. can be D0 - D15. All trigger types using the digital channel are affected.

Usage

Using the .query() method will send the TRIGger:A:SETHold:THReshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:A:SETHold:THReshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:SETHold:THReshold:D<x> value command.

SCPI Syntax

- TRIGger:A:SETHold:THReshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:A:SETHold:THReshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold voltage, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerATimeout ¶

Bases: SCPICmdRead

The TRIGger:A:TIMEOut command tree.

Usage

Using the .query() method will send the TRIGger:A:TIMEOut? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut? query and raise an AssertionError if the returned value does not match value.

Properties

.polarity: The TRIGger:A:TIMEOut:POLarity command.
.source: The TRIGger:A:TIMEOut:SOUrce command.
.time: The TRIGger:A:TIMEOut:TIMe command.

polarity `property` ¶

polarity: TriggerATimeoutPolarity

Return the TRIGger:A:TIMEOut:POLarity command.

Description

When triggering using the TIMEOut trigger type, this commands specifies the polarity to be used.

Usage

Using the .query() method will send the TRIGger:A:TIMEOut:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TIMEOut:POLarity value command.

SCPI Syntax

- TRIGger:A:TIMEOut:POLarity {STAYSHigh|STAYSLow|EITher}
- TRIGger:A:TIMEOut:POLarity?

Info

STAYSHigh . Trigger when the signal stays high during the timeout time specified by the command TRIGGER:A:TIMEOUT:TIME.
STAYSLow . Trigger when the signal stays low during the timeout time specified by the command TRIGGER:A:TIMEOUT:TIME.
EITher . Trigger when the signal is either high or low during the timeout time specified by the command TRIGGER:A:TIMEOUT:TIME.

source `property` ¶

source: TriggerATimeoutSource

Return the TRIGger:A:TIMEOut:SOUrce command.

Description

When triggering using the TIMEOut trigger type, this command specifies the source. The available sources are live channels, the digital channels, the Aux Input connector (for 2-channel MDO32 model only). The default is channel 1. The timeout trigger type is selected using TRIGGER:A:PULSE:CLASS TIMEOut.

Usage

Using the .query() method will send the TRIGger:A:TIMEOut:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TIMEOut:SOUrce value command.

SCPI Syntax

- TRIGger:A:TIMEOut:SOUrce {CH<x>|LINE|AUX|D<x>|RF}
- TRIGger:A:TIMEOut:SOUrce?

Info

CH<x> specifies an analog channel as the timeout trigger source.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (For 2-channel MDO32 model only.).
LINE specifies the AC line as the timeout trigger source.
D<x> specifies a digital channel as the timeout trigger source. (Requires option 3-MSO.).

time `property` ¶

time: TriggerATimeoutTime

Return the TRIGger:A:TIMEOut:TIMe command.

Description

When triggering using the TIMEOut trigger type, this command specifies the timeout time, in seconds. This command is equivalent to selecting Timeout from the Trig menu and setting a value for Time Limit. The timeout trigger type is selected using TRIGGER:A:TYPE TIMEOut

Usage

Using the .query() method will send the TRIGger:A:TIMEOut:TIMe? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut:TIMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TIMEOut:TIMe value command.

SCPI Syntax

- TRIGger:A:TIMEOut:TIMe <NR3>
- TRIGger:A:TIMEOut:TIMe?

Info

<NR3> is a floating point number that specifies the timeout time, in seconds.

TriggerATimeoutPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TIMEOut:POLarity command.

Description

When triggering using the TIMEOut trigger type, this commands specifies the polarity to be used.

Usage

Using the .query() method will send the TRIGger:A:TIMEOut:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TIMEOut:POLarity value command.

SCPI Syntax

- TRIGger:A:TIMEOut:POLarity {STAYSHigh|STAYSLow|EITher}
- TRIGger:A:TIMEOut:POLarity?

Info

STAYSHigh . Trigger when the signal stays high during the timeout time specified by the command TRIGGER:A:TIMEOUT:TIME.
STAYSLow . Trigger when the signal stays low during the timeout time specified by the command TRIGGER:A:TIMEOUT:TIME.
EITher . Trigger when the signal is either high or low during the timeout time specified by the command TRIGGER:A:TIMEOUT:TIME.

TriggerATimeoutSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TIMEOut:SOUrce command.

Description

When triggering using the TIMEOut trigger type, this command specifies the source. The available sources are live channels, the digital channels, the Aux Input connector (for 2-channel MDO32 model only). The default is channel 1. The timeout trigger type is selected using TRIGGER:A:PULSE:CLASS TIMEOut.

Usage

Using the .query() method will send the TRIGger:A:TIMEOut:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TIMEOut:SOUrce value command.

SCPI Syntax

- TRIGger:A:TIMEOut:SOUrce {CH<x>|LINE|AUX|D<x>|RF}
- TRIGger:A:TIMEOut:SOUrce?

Info

CH<x> specifies an analog channel as the timeout trigger source.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope. (For 2-channel MDO32 model only.).
LINE specifies the AC line as the timeout trigger source.
D<x> specifies a digital channel as the timeout trigger source. (Requires option 3-MSO.).

TriggerATimeoutTime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TIMEOut:TIMe command.

Description

When triggering using the TIMEOut trigger type, this command specifies the timeout time, in seconds. This command is equivalent to selecting Timeout from the Trig menu and setting a value for Time Limit. The timeout trigger type is selected using TRIGGER:A:TYPE TIMEOut

Usage

Using the .query() method will send the TRIGger:A:TIMEOut:TIMe? query.
Using the .verify(value) method will send the TRIGger:A:TIMEOut:TIMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TIMEOut:TIMe value command.

SCPI Syntax

- TRIGger:A:TIMEOut:TIMe <NR3>
- TRIGger:A:TIMEOut:TIMe?

Info

<NR3> is a floating point number that specifies the timeout time, in seconds.

TriggerATransition ¶

Bases: SCPICmdRead

The TRIGger:A:TRANsition command.

Description

Returns transition time trigger parameters.

Usage

Using the .query() method will send the TRIGger:A:TRANsition? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:TRANsition?

Properties

.deltatime: The TRIGger:A:TRANsition:DELTatime command.
.polarity: The TRIGger:A:TRANsition:POLarity command.
.source: The TRIGger:A:TRANsition:SOUrce command.
.when: The TRIGger:A:TRANsition:WHEn command.

deltatime `property` ¶

deltatime: TriggerATransitionDeltatime

Return the TRIGger:A:TRANsition:DELTatime command.

Description

This command specifies the delta time used in calculating the transition value for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:DELTatime? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:DELTatime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:DELTatime value command.

SCPI Syntax

- TRIGger:A:TRANsition:DELTatime <NR3>
- TRIGger:A:TRANsition:DELTatime?

Info

<NR3> is a floating point number that specifies the delta time, in seconds.

polarity `property` ¶

polarity: TriggerATransitionPolarity

Return the TRIGger:A:TRANsition:POLarity command.

Description

This command specifies the polarity for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:POLarity value command.

SCPI Syntax

- TRIGger:A:TRANsition:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:TRANsition:POLarity?

Info

POSitive indicates that a pulse edge must traverse from the lower (most negative) to higher (most positive) level for transition triggering to occur.
NEGative indicates that a pulse edge must traverse from the upper (most positive) to lower (most negative) level for transition triggering to occur.
EITher indicates either positive or negative polarity.

source `property` ¶

source: TriggerATransitionSource

Return the TRIGger:A:TRANsition:SOUrce command.

Description

This command specifies the source for a transition trigger.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:SOUrce value command.

SCPI Syntax

- TRIGger:A:TRANsition:SOUrce {CH<x>}
- TRIGger:A:TRANsition:SOUrce?

Info

CH<x> specifies one of the analog channels to be used as the source for a transition trigger.

when `property` ¶

when: TriggerATransitionWhen

Return the TRIGger:A:TRANsition:WHEn command.

Description

This command specifies whether to check for a transitioning signal that is faster or slower than the specified delta time.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:WHEn value command.

SCPI Syntax

- TRIGger:A:TRANsition:WHEn {SLOWer|FASTer|EQual|UNEQual}
- TRIGger:A:TRANsition:WHEn?

Info

FASTer sets the trigger to occur when the signal transition time is faster than the time set by TRIGger:A:TRANsition:DELTatime.
SLOWer sets the trigger to occur when the signal transition time is slower than the time set by.TRIGger:A:TRANsition:DELTatime.
EQual sets the trigger to occur when the signal transition time is equal to the time set by TRIGger:A:TRANsition:DELTatime.
UNEQual sets the trigger to occur when the signal transition time is not equal to the time set by TRIGger:A:TRANsition:DELTatime.

TriggerATransitionDeltatime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TRANsition:DELTatime command.

Description

This command specifies the delta time used in calculating the transition value for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:DELTatime? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:DELTatime? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:DELTatime value command.

SCPI Syntax

- TRIGger:A:TRANsition:DELTatime <NR3>
- TRIGger:A:TRANsition:DELTatime?

Info

<NR3> is a floating point number that specifies the delta time, in seconds.

TriggerATransitionPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TRANsition:POLarity command.

Description

This command specifies the polarity for the transition trigger.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:POLarity value command.

SCPI Syntax

- TRIGger:A:TRANsition:POLarity {EITher|NEGative|POSitive}
- TRIGger:A:TRANsition:POLarity?

Info

POSitive indicates that a pulse edge must traverse from the lower (most negative) to higher (most positive) level for transition triggering to occur.
NEGative indicates that a pulse edge must traverse from the upper (most positive) to lower (most negative) level for transition triggering to occur.
EITher indicates either positive or negative polarity.

TriggerATransitionSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TRANsition:SOUrce command.

Description

This command specifies the source for a transition trigger.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:SOUrce value command.

SCPI Syntax

- TRIGger:A:TRANsition:SOUrce {CH<x>}
- TRIGger:A:TRANsition:SOUrce?

Info

CH<x> specifies one of the analog channels to be used as the source for a transition trigger.

TriggerATransitionWhen ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TRANsition:WHEn command.

Description

This command specifies whether to check for a transitioning signal that is faster or slower than the specified delta time.

Usage

Using the .query() method will send the TRIGger:A:TRANsition:WHEn? query.
Using the .verify(value) method will send the TRIGger:A:TRANsition:WHEn? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TRANsition:WHEn value command.

SCPI Syntax

- TRIGger:A:TRANsition:WHEn {SLOWer|FASTer|EQual|UNEQual}
- TRIGger:A:TRANsition:WHEn?

Info

FASTer sets the trigger to occur when the signal transition time is faster than the time set by TRIGger:A:TRANsition:DELTatime.
SLOWer sets the trigger to occur when the signal transition time is slower than the time set by.TRIGger:A:TRANsition:DELTatime.
EQual sets the trigger to occur when the signal transition time is equal to the time set by TRIGger:A:TRANsition:DELTatime.
UNEQual sets the trigger to occur when the signal transition time is not equal to the time set by TRIGger:A:TRANsition:DELTatime.

TriggerAType ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:TYPe command.

Description

This command sets the type of A trigger (either edge, logic, pulse, bus or video). If you set the trigger type to LOGIc, you also need to set the logic trigger class (logic or setup/hold) using the command TRIGGER:A:LOGIC:CLASS. If you set the trigger type to PULSe, you also need to set the pulse trigger class (either runt, width, transition or timeout), using the command TRIGGER:A:PULSE:CLASS. If you set the trigger type to BUS, you also need to set the bus type (CAN, I 2 C, SPI, RS-232, Ethernet, MIL-STD-1553, LIN, USB, audio, FlexRay, or parallel) using the command TRIGGER:A:BUS.

Usage

Using the .query() method will send the TRIGger:A:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:TYPe value command.

SCPI Syntax

- TRIGger:A:TYPe {EDGe|LOGIc|PULSe|BUS|VIDeo}
- TRIGger:A:TYPe?

Info

EDGe is the default trigger. A trigger event occurs when a signal passes through a specified voltage level in a specified direction and is controlled by the TRIGGER:A:EDGE commands.
LOGIc specifies that a trigger occurs when specified conditions are met and is controlled by the TRIGGER:A:LOGIC commands. This trigger type is equivalent to the logic and setup/hold triggers found in the user interface. Use TRIGGER:A:LOGIC:CLASS to further select the logic trigger class (either LOGIC or SETHOLD).
PULSe specifies that a trigger occurs when a specified pulse is found. Use TRIGGER:A:PULSE:CLASS to further select the pulse trigger class (either runt, width, transition or timeout).
BUS specifies that a trigger occurs when a bus signal is found. Supports CAN, I2C, SPI, RS-232, Ethernet, MIL-STD-1553, LIN, USB, audio, FlexRay buses (with the appropriate application module installed) as well as parallel buses. Requires the installation of option 3-MSO. Use TRIGGER:A:BUS to set the bus type.
VIDeo specifies that the trigger occurs when a video signal is found.

TriggerAUpperthreshold ¶

Bases: SCPICmdRead

The TRIGger:A:UPPerthreshold command tree.

Usage

Using the .query() method will send the TRIGger:A:UPPerthreshold? query.
Using the .verify(value) method will send the TRIGger:A:UPPerthreshold? query and raise an AssertionError if the returned value does not match value.

Properties

.ch: The TRIGger:A:UPPerthreshold:CH<x> command.
.rf: The TRIGger:A:UPPerthreshold:RF command.

ch `property` ¶

ch: dict[int, TriggerAUpperthresholdChannel]

Return the TRIGger:A:UPPerthreshold:CH<x> command.

Description

This command sets the upper threshold for channel , where x is the analog channel number 1-4. Each channel can have an independent level. Used only for runt and transition trigger types.

Usage

Using the .query() method will send the TRIGger:A:UPPerthreshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:UPPerthreshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:UPPerthreshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:UPPerthreshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:UPPerthreshold:CH<x>?

Info

<NR3> is a floating point number that specifies the threshold level, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

rf `property` ¶

rf: TriggerAUpperthresholdRf

Return the TRIGger:A:UPPerthreshold:RF command.

Description

This command specifies the upper threshold when the internal RF power level is used during runt triggering. To specify the lower threshold for the RUNT trigger type as well as the single threshold for the Pulse and Timeout trigger types, use the command TRIGGER:A:LOWERTHRESHOLD:RF. To choose the RUNT trigger type, use the command TRIGGER:A:PULSE:CLASS. To specify RF power as a source during runt triggering, use TRIGGER:A:RUNT:SOURCE.

Usage

Using the .query() method will send the TRIGger:A:UPPerthreshold:RF? query.
Using the .verify(value) method will send the TRIGger:A:UPPerthreshold:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:UPPerthreshold:RF value command.

SCPI Syntax

- TRIGger:A:UPPerthreshold:RF {<NR3>}
- TRIGger:A:UPPerthreshold:RF?

Info

<NR3> is a floating point number that specifies the threshold to use, in the currently selected RF units (using RF:UNITS). The range is (ref level - 40 dBm) to (ref level + 10 dBm), but never less than -65 dBm or more than +30 dBm.

TriggerAUpperthresholdChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:A:UPPerthreshold:CH<x> command.

Description

This command sets the upper threshold for channel , where x is the analog channel number 1-4. Each channel can have an independent level. Used only for runt and transition trigger types.

Usage

Using the .query() method will send the TRIGger:A:UPPerthreshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:A:UPPerthreshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:UPPerthreshold:CH<x> value command.

SCPI Syntax

- TRIGger:A:UPPerthreshold:CH<x> {<NR3>|ECL|TTL}
- TRIGger:A:UPPerthreshold:CH<x>?

Info

<NR3> is a floating point number that specifies the threshold level, in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerAUpperthresholdRf ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:UPPerthreshold:RF command.

Description

This command specifies the upper threshold when the internal RF power level is used during runt triggering. To specify the lower threshold for the RUNT trigger type as well as the single threshold for the Pulse and Timeout trigger types, use the command TRIGGER:A:LOWERTHRESHOLD:RF. To choose the RUNT trigger type, use the command TRIGGER:A:PULSE:CLASS. To specify RF power as a source during runt triggering, use TRIGGER:A:RUNT:SOURCE.

Usage

Using the .query() method will send the TRIGger:A:UPPerthreshold:RF? query.
Using the .verify(value) method will send the TRIGger:A:UPPerthreshold:RF? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:UPPerthreshold:RF value command.

SCPI Syntax

- TRIGger:A:UPPerthreshold:RF {<NR3>}
- TRIGger:A:UPPerthreshold:RF?

Info

<NR3> is a floating point number that specifies the threshold to use, in the currently selected RF units (using RF:UNITS). The range is (ref level - 40 dBm) to (ref level + 10 dBm), but never less than -65 dBm or more than +30 dBm.

TriggerAVideo ¶

Bases: SCPICmdRead

The TRIGger:A:VIDeo command.

Description

Returns the A trigger video parameters.

Usage

Using the .query() method will send the TRIGger:A:VIDeo? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:A:VIDeo?

Properties

.custom: The TRIGger:A:VIDeo:CUSTom command tree.
.holdoff: The TRIGger:A:VIDeo:HOLDoff command tree.
.line: The TRIGger:A:VIDeo:LINE command.
.polarity: The TRIGger:A:VIDeo:POLarity command.
.source: The TRIGger:A:VIDeo:SOUrce command.
.standard: The TRIGger:A:VIDeo:STANdard command.
.sync: The TRIGger:A:VIDeo:SYNC command.
.field: The TRIGger:A:VIDeo:FIELD command.

custom `property` ¶

custom: TriggerAVideoCustom

Return the TRIGger:A:VIDeo:CUSTom command tree.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.lineperiod: The TRIGger:A:VIDeo:CUSTom:LINEPeriod command.
.syncinterval: The TRIGger:A:VIDeo:CUSTom:SYNCInterval command.
.format: The TRIGger:A:VIDeo:CUSTom:FORMat command.
.type: The TRIGger:A:VIDeo:CUSTom:TYPe command.

field `property` ¶

field: TriggerAVideoField

Return the TRIGger:A:VIDeo:FIELD command.

Description

This command sets the video field to use for triggering on video signals (odd fields, even fields, all fields, all lines, numeric).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:FIELD? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:FIELD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:FIELD value command.

SCPI Syntax

- TRIGger:A:VIDeo:FIELD {ODD|EVEN|ALLFields|ALLLines|NUMERic}
- TRIGger:A:VIDeo:FIELD?

Info

ODD argument sets the oscilloscope to trigger on interlaced video odd fields.
EVEN argument sets the oscilloscope to trigger on interlaced video even fields.
ALLFields argument sets the oscilloscope to trigger on all fields.
ALLLines argument sets the oscilloscope to trigger on all video lines.
NUMERic argument sets the oscilloscope to trigger on the video signal line specified by the TRIGGER:A:VIDEO:LINE command.

holdoff `property` ¶

holdoff: TriggerAVideoHoldoff

Return the TRIGger:A:VIDeo:HOLDoff command tree.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:HOLDoff? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:HOLDoff? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.field: The TRIGger:A:VIDeo:HOLDoff:FIELD command.

line `property` ¶

line: TriggerAVideoLine

Return the TRIGger:A:VIDeo:LINE command.

Description

This command lets you set the specific video line number to be used for triggering on a video signal. You must also use the command to specify NUMERic as the video field to use.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:LINE? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:LINE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:LINE value command.

SCPI Syntax

- TRIGger:A:VIDeo:LINE <NR1>
- TRIGger:A:VIDeo:LINE?

Info

<NR1> argument is an integer that sets the video line number on which the oscilloscope triggers. The following table lists the valid choices, depending on the active video standard.

polarity `property` ¶

polarity: TriggerAVideoPolarity

Return the TRIGger:A:VIDeo:POLarity command.

Description

This command sets the polarity to use for triggering on video signals.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:POLarity value command.

SCPI Syntax

- TRIGger:A:VIDeo:POLarity {NEGative|POSitive}
- TRIGger:A:VIDeo:POLarity?

Info

POSitive argument sets the oscilloscope to trigger on a positive video sync pulse.
NEGative argument sets the oscilloscope to trigger on a negative video sync pulse.

source `property` ¶

source: TriggerAVideoSource

Return the TRIGger:A:VIDeo:SOUrce command.

Description

This command sets the source channel to use for triggering on video signals (CH1-4).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:SOUrce value command.

SCPI Syntax

- TRIGger:A:VIDeo:SOUrce {CH<x>}
- TRIGger:A:VIDeo:SOUrce?

Info

CH<x> specifies the input channel to use as the A video trigger. x has a minimum of 1 and a maximum of 4.

standard `property` ¶

standard: TriggerAVideoStandard

Return the TRIGger:A:VIDeo:STANdard command.

Description

This command sets the standard to use for triggering on video signals.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:STANdard? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:STANdard? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:STANdard value command.

SCPI Syntax

- TRIGger:A:VIDeo:STANdard {NTSc|PAL|SECAM|BILevelcustom|TRILevelcustom|HD480P60|HD576P50|HD720P30|HD720P50|HD720P60|HD875I60|HD1080P24|HD1080SF24|HD1080I50|HD1080I60|HD1080P25|HD1080P30|HD1080P50|HD1080P60}
- TRIGger:A:VIDeo:STANdard?

Info

NTSc sets the oscilloscope to trigger on video signals that meet the NTSC 525/60/2:1 standard (a line rate of 525 lines per frame and a field rate of 60 Hz).
PAL sets the oscilloscope to trigger on video signals that meet the NTSC 625/50/2:1 standard (a line rate of 625 lines per frame and a field rate of 50 Hz).
SECAM sets the oscilloscope to trigger on video signals that meet the SECAM standard.
BILevelcustom sets the oscilloscope to trigger on video horizontal scan rate parameters defined by the.
TRILevelcustom sets the oscilloscope to trigger on video horizontal scan rate parameters defined by the.
HD480P60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD576P50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD720P30 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD720P50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD720P60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD875I60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P24 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080SF24 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080I50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080I60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P25 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P30 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.

sync `property` ¶

sync: TriggerAVideoSync

Return the TRIGger:A:VIDeo:SYNC command.

Description

This command sets the video field to use for triggering on video signals (odd fields, even fields, all fields, all lines, numeric).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:SYNC? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:SYNC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:SYNC value command.

SCPI Syntax

- TRIGger:A:VIDeo:SYNC {ODD|EVEN|ALLFields|ALLLines|NUMERic}
- TRIGger:A:VIDeo:SYNC?

Info

ODD argument sets the oscilloscope to trigger on interlaced video odd fields.
EVEN argument sets the oscilloscope to trigger on interlaced video even fields.
ALLFields argument sets the oscilloscope to trigger on all fields.
ALLLines argument sets the oscilloscope to trigger on all video lines.
NUMERic argument sets the oscilloscope to trigger on the video signal line specified by the TRIGGER:A:VIDEO:LINE command.

TriggerAVideoCustom ¶

Bases: SCPICmdRead

The TRIGger:A:VIDeo:CUSTom command tree.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom? query and raise an AssertionError if the returned value does not match value.

Properties

.lineperiod: The TRIGger:A:VIDeo:CUSTom:LINEPeriod command.
.syncinterval: The TRIGger:A:VIDeo:CUSTom:SYNCInterval command.
.format: The TRIGger:A:VIDeo:CUSTom:FORMat command.
.type: The TRIGger:A:VIDeo:CUSTom:TYPe command.

format `property` ¶

format: TriggerAVideoCustomFormat

Return the TRIGger:A:VIDeo:CUSTom:FORMat command.

Description

This command sets the video trigger format (either interlaced or progressive) to use for triggering on video signals. To use this command, you must also set the video standard to BILevelcustom or TRILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:FORMat? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:FORMat? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:FORMat value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:FORMat {INTERLAced|PROGressive}
- TRIGger:A:VIDeo:CUSTom:FORMat?

Info

INTERLAced argument sets the format to interlaced video lines.
PROGressive argument sets the format to progressive video lines.

lineperiod `property` ¶

lineperiod: TriggerAVideoCustomLineperiod

Return the TRIGger:A:VIDeo:CUSTom:LINEPeriod command.

Description

This command sets the line period for the standard under test. To use this command, you must also set the video standard to BILevelcustom or TRILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:LINEPeriod? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:LINEPeriod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:LINEPeriod value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:LINEPeriod <NR3>
- TRIGger:A:VIDeo:CUSTom:LINEPeriod?

Info

<NR3> is the custom video line period.

syncinterval `property` ¶

syncinterval: TriggerAVideoCustomSyncinterval

Return the TRIGger:A:VIDeo:CUSTom:SYNCInterval command.

Description

This command sets the sync interval for the standard under test to use for triggering on video signals. This is only required for BiLevel Custom. To use this command, you must also set the video standard to BILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:SYNCInterval? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:SYNCInterval? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:SYNCInterval value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:SYNCInterval <NR3>
- TRIGger:A:VIDeo:CUSTom:SYNCInterval?

Info

<NR3> is the sync interval.

type `property` ¶

type: TriggerAVideoCustomType

Return the TRIGger:A:VIDeo:CUSTom:TYPe command.

Description

This command sets the video trigger format (either interlaced or progressive) to use for triggering on video signals. To use this command, you must also set the video standard to BILevelcustom or TRILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:TYPe value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:TYPe {INTERLAced|PROGressive}
- TRIGger:A:VIDeo:CUSTom:TYPe?

Info

INTERLAced argument sets the format to interlaced video lines.
PROGressive argument sets the format to progressive video lines.

TriggerAVideoCustomFormat ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:CUSTom:FORMat command.

Description

This command sets the video trigger format (either interlaced or progressive) to use for triggering on video signals. To use this command, you must also set the video standard to BILevelcustom or TRILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:FORMat? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:FORMat? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:FORMat value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:FORMat {INTERLAced|PROGressive}
- TRIGger:A:VIDeo:CUSTom:FORMat?

Info

INTERLAced argument sets the format to interlaced video lines.
PROGressive argument sets the format to progressive video lines.

TriggerAVideoCustomLineperiod ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:CUSTom:LINEPeriod command.

Description

This command sets the line period for the standard under test. To use this command, you must also set the video standard to BILevelcustom or TRILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:LINEPeriod? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:LINEPeriod? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:LINEPeriod value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:LINEPeriod <NR3>
- TRIGger:A:VIDeo:CUSTom:LINEPeriod?

Info

<NR3> is the custom video line period.

TriggerAVideoCustomSyncinterval ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:CUSTom:SYNCInterval command.

Description

This command sets the sync interval for the standard under test to use for triggering on video signals. This is only required for BiLevel Custom. To use this command, you must also set the video standard to BILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:SYNCInterval? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:SYNCInterval? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:SYNCInterval value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:SYNCInterval <NR3>
- TRIGger:A:VIDeo:CUSTom:SYNCInterval?

Info

<NR3> is the sync interval.

TriggerAVideoCustomType ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:CUSTom:TYPe command.

Description

This command sets the video trigger format (either interlaced or progressive) to use for triggering on video signals. To use this command, you must also set the video standard to BILevelcustom or TRILevelcustom (using TRIGGER:A:VIDEO:STANDARD).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:CUSTom:TYPe? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:CUSTom:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:CUSTom:TYPe value command.

SCPI Syntax

- TRIGger:A:VIDeo:CUSTom:TYPe {INTERLAced|PROGressive}
- TRIGger:A:VIDeo:CUSTom:TYPe?

Info

INTERLAced argument sets the format to interlaced video lines.
PROGressive argument sets the format to progressive video lines.

TriggerAVideoField ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:FIELD command.

Description

This command sets the video field to use for triggering on video signals (odd fields, even fields, all fields, all lines, numeric).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:FIELD? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:FIELD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:FIELD value command.

SCPI Syntax

- TRIGger:A:VIDeo:FIELD {ODD|EVEN|ALLFields|ALLLines|NUMERic}
- TRIGger:A:VIDeo:FIELD?

Info

ODD argument sets the oscilloscope to trigger on interlaced video odd fields.
EVEN argument sets the oscilloscope to trigger on interlaced video even fields.
ALLFields argument sets the oscilloscope to trigger on all fields.
ALLLines argument sets the oscilloscope to trigger on all video lines.
NUMERic argument sets the oscilloscope to trigger on the video signal line specified by the TRIGGER:A:VIDEO:LINE command.

TriggerAVideoHoldoff ¶

Bases: SCPICmdRead

The TRIGger:A:VIDeo:HOLDoff command tree.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:HOLDoff? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:HOLDoff? query and raise an AssertionError if the returned value does not match value.

Properties

.field: The TRIGger:A:VIDeo:HOLDoff:FIELD command.

field `property` ¶

field: TriggerAVideoHoldoffField

Return the TRIGger:A:VIDeo:HOLDoff:FIELD command.

Description

This command sets the video trigger holdoff, in terms of video fields, to use for triggering on video signals.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:HOLDoff:FIELD? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:HOLDoff:FIELD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:HOLDoff:FIELD value command.

SCPI Syntax

- TRIGger:A:VIDeo:HOLDoff:FIELD <NR3>
- TRIGger:A:VIDeo:HOLDoff:FIELD?

Info

<NR3> argument is a real number from 0.0 to 8.5 in increments of 0.5. The argument sets the number of fields that the oscilloscope waits before rearming the video trigger.

TriggerAVideoHoldoffField ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:HOLDoff:FIELD command.

Description

This command sets the video trigger holdoff, in terms of video fields, to use for triggering on video signals.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:HOLDoff:FIELD? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:HOLDoff:FIELD? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:HOLDoff:FIELD value command.

SCPI Syntax

- TRIGger:A:VIDeo:HOLDoff:FIELD <NR3>
- TRIGger:A:VIDeo:HOLDoff:FIELD?

Info

<NR3> argument is a real number from 0.0 to 8.5 in increments of 0.5. The argument sets the number of fields that the oscilloscope waits before rearming the video trigger.

TriggerAVideoLine ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:LINE command.

Description

This command lets you set the specific video line number to be used for triggering on a video signal. You must also use the command to specify NUMERic as the video field to use.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:LINE? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:LINE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:LINE value command.

SCPI Syntax

- TRIGger:A:VIDeo:LINE <NR1>
- TRIGger:A:VIDeo:LINE?

Info

<NR1> argument is an integer that sets the video line number on which the oscilloscope triggers. The following table lists the valid choices, depending on the active video standard.

TriggerAVideoPolarity ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:POLarity command.

Description

This command sets the polarity to use for triggering on video signals.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:POLarity? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:POLarity? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:POLarity value command.

SCPI Syntax

- TRIGger:A:VIDeo:POLarity {NEGative|POSitive}
- TRIGger:A:VIDeo:POLarity?

Info

POSitive argument sets the oscilloscope to trigger on a positive video sync pulse.
NEGative argument sets the oscilloscope to trigger on a negative video sync pulse.

TriggerAVideoSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:SOUrce command.

Description

This command sets the source channel to use for triggering on video signals (CH1-4).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:SOUrce? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:SOUrce value command.

SCPI Syntax

- TRIGger:A:VIDeo:SOUrce {CH<x>}
- TRIGger:A:VIDeo:SOUrce?

Info

CH<x> specifies the input channel to use as the A video trigger. x has a minimum of 1 and a maximum of 4.

TriggerAVideoStandard ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:STANdard command.

Description

This command sets the standard to use for triggering on video signals.

Usage

Using the .query() method will send the TRIGger:A:VIDeo:STANdard? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:STANdard? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:STANdard value command.

SCPI Syntax

- TRIGger:A:VIDeo:STANdard {NTSc|PAL|SECAM|BILevelcustom|TRILevelcustom|HD480P60|HD576P50|HD720P30|HD720P50|HD720P60|HD875I60|HD1080P24|HD1080SF24|HD1080I50|HD1080I60|HD1080P25|HD1080P30|HD1080P50|HD1080P60}
- TRIGger:A:VIDeo:STANdard?

Info

NTSc sets the oscilloscope to trigger on video signals that meet the NTSC 525/60/2:1 standard (a line rate of 525 lines per frame and a field rate of 60 Hz).
PAL sets the oscilloscope to trigger on video signals that meet the NTSC 625/50/2:1 standard (a line rate of 625 lines per frame and a field rate of 50 Hz).
SECAM sets the oscilloscope to trigger on video signals that meet the SECAM standard.
BILevelcustom sets the oscilloscope to trigger on video horizontal scan rate parameters defined by the.
TRILevelcustom sets the oscilloscope to trigger on video horizontal scan rate parameters defined by the.
HD480P60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD576P50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD720P30 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD720P50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD720P60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD875I60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P24 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080SF24 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080I50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080I60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P25 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P30 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P50 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.
HD1080P60 set the oscilloscope to trigger on an HDTV video signal that meets standards defined in the following table.

TriggerAVideoSync ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:A:VIDeo:SYNC command.

Description

This command sets the video field to use for triggering on video signals (odd fields, even fields, all fields, all lines, numeric).

Usage

Using the .query() method will send the TRIGger:A:VIDeo:SYNC? query.
Using the .verify(value) method will send the TRIGger:A:VIDeo:SYNC? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:A:VIDeo:SYNC value command.

SCPI Syntax

- TRIGger:A:VIDeo:SYNC {ODD|EVEN|ALLFields|ALLLines|NUMERic}
- TRIGger:A:VIDeo:SYNC?

Info

ODD argument sets the oscilloscope to trigger on interlaced video odd fields.
EVEN argument sets the oscilloscope to trigger on interlaced video even fields.
ALLFields argument sets the oscilloscope to trigger on all fields.
ALLLines argument sets the oscilloscope to trigger on all video lines.
NUMERic argument sets the oscilloscope to trigger on the video signal line specified by the TRIGGER:A:VIDEO:LINE command.

TriggerB ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B command.

Description

Sets the B trigger level to 50% of minimum and maximum. The query form of this command returns the B trigger parameters. This command is similar to selecting B Event (Delayed) Trigger Setup from the Trigger menu and then viewing the current setups.

Usage

Using the .query() method will send the TRIGger:B? query.
Using the .verify(value) method will send the TRIGger:B? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B value command.

SCPI Syntax

- TRIGger:B SETLevel
- TRIGger:B?

Info

SETLevel sets the B trigger level to 50% of MIN and MAX.

Properties

.by: The TRIGger:B:BY command.
.edge: The TRIGger:B:EDGE command.
.events: The TRIGger:B:EVENTS command.
.level: The TRIGger:B:LEVel command.
.lowerthreshold: The TRIGger:B:LOWerthreshold command tree.
.state: The TRIGger:B:STATE command.
.time: The TRIGger:B:TIMe command.
.type: The TRIGger:B:TYPe command.

by `property` ¶

by: TriggerBBy

Return the TRIGger:B:BY command.

Description

Selects or returns whether the B trigger occurs after a specified number of events or a specified period of time after the A trigger.

Usage

Using the .query() method will send the TRIGger:B:BY? query.
Using the .verify(value) method will send the TRIGger:B:BY? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:BY value command.

SCPI Syntax

- TRIGger:B:BY {EVENTS|TIMe}
- TRIGger:B:BY?

Info

EVENTS sets the B trigger to take place following a set number of trigger events after the A trigger occurs. The number of events is specified by TRIGger:B:EVENTS:COUNt.
TIMe sets the B trigger to occur a set time after the A trigger event. The time period is specified by TRIGger:B:TIMe.

edge `property` ¶

edge: TriggerBEdge

Return the TRIGger:B:EDGE command.

Description

Returns the source, slope, and coupling for B trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE? query.
Using the .verify(value) method will send the TRIGger:B:EDGE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:B:EDGE?

Sub-properties

.coupling: The TRIGger:B:EDGE:COUPling command.
.slope: The TRIGger:B:EDGE:SLOpe command.
.source: The TRIGger:B:EDGE:SOUrce command.

events `property` ¶

events: TriggerBEvents

Return the TRIGger:B:EVENTS command.

Description

Returns the current B trigger events parameter.

Usage

Using the .query() method will send the TRIGger:B:EVENTS? query.
Using the .verify(value) method will send the TRIGger:B:EVENTS? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:B:EVENTS?

Sub-properties

.count: The TRIGger:B:EVENTS:COUNt command.

level `property` ¶

level: TriggerBLevel

Return the TRIGger:B:LEVel command.

Description

This command specifies the level for the B trigger.

Usage

Using the .query() method will send the TRIGger:B:LEVel? query.
Using the .verify(value) method will send the TRIGger:B:LEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LEVel value command.

SCPI Syntax

- TRIGger:B:LEVel {TTL|<NR3>}
- TRIGger:B:LEVel?

Info

TTL specifies a preset TTL high level of 1.4 V.
<NR3> is a floating point number that specifies the B trigger level, in volts.

Sub-properties

.ch: The TRIGger:B:LEVel:CH<x> command.
.d: The TRIGger:B:LEVel:D<x> command.

lowerthreshold `property` ¶

lowerthreshold: TriggerBLowerthreshold

Return the TRIGger:B:LOWerthreshold command tree.

Usage

Using the .query() method will send the TRIGger:B:LOWerthreshold? query.
Using the .verify(value) method will send the TRIGger:B:LOWerthreshold? query and raise an AssertionError if the returned value does not match value.

Sub-properties

.ch: The TRIGger:B:LOWerthreshold:CH<x> command.
.d: The TRIGger:B:LOWerthreshold:D<x> command.

state `property` ¶

state: TriggerBState

Return the TRIGger:B:STATE command.

Description

This command specifies the state of B trigger activity. If the B trigger state is on, the B trigger is part of the triggering sequence. If the B trigger state is off, then only the A trigger causes the trigger event.

Usage

Using the .query() method will send the TRIGger:B:STATE? query.
Using the .verify(value) method will send the TRIGger:B:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:STATE value command.

SCPI Syntax

- TRIGger:B:STATE {ON|OFF|<NR1>}
- TRIGger:B:STATE?

Info

ON specifies that the B trigger is active and in causes trigger events conjunction with the A trigger.
OFF specifies that only the A trigger causes trigger events.
<NR1> a 0 turns off the B trigger; any other value activates the B trigger.

time `property` ¶

time: TriggerBTime

Return the TRIGger:B:TIMe command.

Description

This command specifies B trigger delay time. The B Trigger time applies only if TRIGger:B:BY is set to TIMe.

Usage

Using the .query() method will send the TRIGger:B:TIMe? query.
Using the .verify(value) method will send the TRIGger:B:TIMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:TIMe value command.

SCPI Syntax

- TRIGger:B:TIMe <NR3>
- TRIGger:B:TIMe?

Info

<NR3> is a floating point number that specifies the B trigger delay time in seconds.

type `property` ¶

type: TriggerBType

Return the TRIGger:B:TYPe command.

Description

This command specifies the type of B trigger. The only supported B trigger type is EDGE.

Usage

Using the .query() method will send the TRIGger:B:TYPe? query.
Using the .verify(value) method will send the TRIGger:B:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:TYPe value command.

SCPI Syntax

- TRIGger:B:TYPe EDGE
- TRIGger:B:TYPe?

Info

EDGE sets the B trigger type to edge.

TriggerBBy ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:BY command.

Description

Selects or returns whether the B trigger occurs after a specified number of events or a specified period of time after the A trigger.

Usage

Using the .query() method will send the TRIGger:B:BY? query.
Using the .verify(value) method will send the TRIGger:B:BY? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:BY value command.

SCPI Syntax

- TRIGger:B:BY {EVENTS|TIMe}
- TRIGger:B:BY?

Info

EVENTS sets the B trigger to take place following a set number of trigger events after the A trigger occurs. The number of events is specified by TRIGger:B:EVENTS:COUNt.
TIMe sets the B trigger to occur a set time after the A trigger event. The time period is specified by TRIGger:B:TIMe.

TriggerBEdge ¶

Bases: SCPICmdRead

The TRIGger:B:EDGE command.

Description

Returns the source, slope, and coupling for B trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE? query.
Using the .verify(value) method will send the TRIGger:B:EDGE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:B:EDGE?

Properties

.coupling: The TRIGger:B:EDGE:COUPling command.
.slope: The TRIGger:B:EDGE:SLOpe command.
.source: The TRIGger:B:EDGE:SOUrce command.

coupling `property` ¶

coupling: TriggerBEdgeCoupling

Return the TRIGger:B:EDGE:COUPling command.

Description

This command specifies the type of coupling for the B edge trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE:COUPling? query.
Using the .verify(value) method will send the TRIGger:B:EDGE:COUPling? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EDGE:COUPling value command.

SCPI Syntax

- TRIGger:B:EDGE:COUPling {DC|HFRej|LFRej|NOISErej}
- TRIGger:B:EDGE:COUPling?

Info

DC selects DC trigger coupling.
HFRej selects high-frequency reject coupling.
LFRej selects low-frequency reject coupling.
NOISErej selects DC low sensitivity.

slope `property` ¶

slope: TriggerBEdgeSlope

Return the TRIGger:B:EDGE:SLOpe command.

Description

This command specifies the slope for the B trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE:SLOpe? query.
Using the .verify(value) method will send the TRIGger:B:EDGE:SLOpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EDGE:SLOpe value command.

SCPI Syntax

- TRIGger:B:EDGE:SLOpe {RISe|FALL}
- TRIGger:B:EDGE:SLOpe?

Info

RISe triggers on the rising or positive edge of a signal.
FALL triggers on the falling or negative edge of a signal.

source `property` ¶

source: TriggerBEdgeSource

Return the TRIGger:B:EDGE:SOUrce command.

Description

This command specifies the source for the B trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE:SOUrce? query.
Using the .verify(value) method will send the TRIGger:B:EDGE:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EDGE:SOUrce value command.

SCPI Syntax

- TRIGger:B:EDGE:SOUrce {CH<x>|AUX|LINE|RF}
- TRIGger:B:EDGE:SOUrce?

Info

CH<x> specifies an analog channel as the B trigger source.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope as the B trigger source. (For 2-channel MDO32 model only.).
LINE specifies the AC power line as the B trigger source.

TriggerBEdgeCoupling ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:EDGE:COUPling command.

Description

This command specifies the type of coupling for the B edge trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE:COUPling? query.
Using the .verify(value) method will send the TRIGger:B:EDGE:COUPling? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EDGE:COUPling value command.

SCPI Syntax

- TRIGger:B:EDGE:COUPling {DC|HFRej|LFRej|NOISErej}
- TRIGger:B:EDGE:COUPling?

Info

DC selects DC trigger coupling.
HFRej selects high-frequency reject coupling.
LFRej selects low-frequency reject coupling.
NOISErej selects DC low sensitivity.

TriggerBEdgeSlope ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:EDGE:SLOpe command.

Description

This command specifies the slope for the B trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE:SLOpe? query.
Using the .verify(value) method will send the TRIGger:B:EDGE:SLOpe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EDGE:SLOpe value command.

SCPI Syntax

- TRIGger:B:EDGE:SLOpe {RISe|FALL}
- TRIGger:B:EDGE:SLOpe?

Info

RISe triggers on the rising or positive edge of a signal.
FALL triggers on the falling or negative edge of a signal.

TriggerBEdgeSource ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:EDGE:SOUrce command.

Description

This command specifies the source for the B trigger.

Usage

Using the .query() method will send the TRIGger:B:EDGE:SOUrce? query.
Using the .verify(value) method will send the TRIGger:B:EDGE:SOUrce? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EDGE:SOUrce value command.

SCPI Syntax

- TRIGger:B:EDGE:SOUrce {CH<x>|AUX|LINE|RF}
- TRIGger:B:EDGE:SOUrce?

Info

CH<x> specifies an analog channel as the B trigger source.
AUX specifies an external trigger using the Aux In connector located on the front panel of the oscilloscope as the B trigger source. (For 2-channel MDO32 model only.).
LINE specifies the AC power line as the B trigger source.

TriggerBEvents ¶

Bases: SCPICmdRead

The TRIGger:B:EVENTS command.

Description

Returns the current B trigger events parameter.

Usage

Using the .query() method will send the TRIGger:B:EVENTS? query.
Using the .verify(value) method will send the TRIGger:B:EVENTS? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:B:EVENTS?

Properties

.count: The TRIGger:B:EVENTS:COUNt command.

count `property` ¶

count: TriggerBEventsCount

Return the TRIGger:B:EVENTS:COUNt command.

Description

This command specifies the number of events that must occur before the B trigger (when TRIG:DELay:BY is set to EVENTS).

Usage

Using the .query() method will send the TRIGger:B:EVENTS:COUNt? query.
Using the .verify(value) method will send the TRIGger:B:EVENTS:COUNt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EVENTS:COUNt value command.

SCPI Syntax

- TRIGger:B:EVENTS:COUNt <NR1>
- TRIGger:B:EVENTS:COUNt?

Info

<NR1> is the number of B trigger events, which can range from 1 to 10,000,000.

TriggerBEventsCount ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:EVENTS:COUNt command.

Description

This command specifies the number of events that must occur before the B trigger (when TRIG:DELay:BY is set to EVENTS).

Usage

Using the .query() method will send the TRIGger:B:EVENTS:COUNt? query.
Using the .verify(value) method will send the TRIGger:B:EVENTS:COUNt? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:EVENTS:COUNt value command.

SCPI Syntax

- TRIGger:B:EVENTS:COUNt <NR1>
- TRIGger:B:EVENTS:COUNt?

Info

<NR1> is the number of B trigger events, which can range from 1 to 10,000,000.

TriggerBLevel ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:LEVel command.

Description

This command specifies the level for the B trigger.

Usage

Using the .query() method will send the TRIGger:B:LEVel? query.
Using the .verify(value) method will send the TRIGger:B:LEVel? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LEVel value command.

SCPI Syntax

- TRIGger:B:LEVel {TTL|<NR3>}
- TRIGger:B:LEVel?

Info

TTL specifies a preset TTL high level of 1.4 V.
<NR3> is a floating point number that specifies the B trigger level, in volts.

Properties

.ch: The TRIGger:B:LEVel:CH<x> command.
.d: The TRIGger:B:LEVel:D<x> command.

ch `property` ¶

ch: dict[int, TriggerBLevelChannel]

Return the TRIGger:B:LEVel:CH<x> command.

Description

This command specifies the B trigger level for channel , where x is the channel number. Each Channel can have an independent Level.

Usage

Using the .query() method will send the TRIGger:B:LEVel:CH<x>? query.
Using the .verify(value) method will send the TRIGger:B:LEVel:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LEVel:CH<x> value command.

SCPI Syntax

- TRIGger:B:LEVel:CH<x> {ECL|TTL|<NR3>}
- TRIGger:B:LEVel:CH<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the trigger level in user units (usually volts).

d `property` ¶

d: dict[int, TriggerBLevelDigitalBit]

Return the TRIGger:B:LEVel:D<x> command.

Description

This command specifies the B trigger level for digital channel , where x is the channel number. Each channel can have an independent level.

Usage

Using the .query() method will send the TRIGger:B:LEVel:D<x>? query.
Using the .verify(value) method will send the TRIGger:B:LEVel:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LEVel:D<x> value command.

SCPI Syntax

- TRIGger:B:LEVel:D<x> {ECL|TTL|<NR3>}
- TRIGger:B:LEVel:D<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the trigger level in user units (usually volts).

TriggerBLevelChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:B:LEVel:CH<x> command.

Description

This command specifies the B trigger level for channel , where x is the channel number. Each Channel can have an independent Level.

Usage

Using the .query() method will send the TRIGger:B:LEVel:CH<x>? query.
Using the .verify(value) method will send the TRIGger:B:LEVel:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LEVel:CH<x> value command.

SCPI Syntax

- TRIGger:B:LEVel:CH<x> {ECL|TTL|<NR3>}
- TRIGger:B:LEVel:CH<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the trigger level in user units (usually volts).

TriggerBLevelDigitalBit ¶

Bases: ValidatedDigitalBit, SCPICmdWrite, SCPICmdRead

The TRIGger:B:LEVel:D<x> command.

Description

This command specifies the B trigger level for digital channel , where x is the channel number. Each channel can have an independent level.

Usage

Using the .query() method will send the TRIGger:B:LEVel:D<x>? query.
Using the .verify(value) method will send the TRIGger:B:LEVel:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LEVel:D<x> value command.

SCPI Syntax

- TRIGger:B:LEVel:D<x> {ECL|TTL|<NR3>}
- TRIGger:B:LEVel:D<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the trigger level in user units (usually volts).

TriggerBLowerthreshold ¶

Bases: SCPICmdRead

The TRIGger:B:LOWerthreshold command tree.

Usage

Using the .query() method will send the TRIGger:B:LOWerthreshold? query.
Using the .verify(value) method will send the TRIGger:B:LOWerthreshold? query and raise an AssertionError if the returned value does not match value.

Properties

.ch: The TRIGger:B:LOWerthreshold:CH<x> command.
.d: The TRIGger:B:LOWerthreshold:D<x> command.

ch `property` ¶

ch: dict[int, TriggerBLowerthresholdChannel]

Return the TRIGger:B:LOWerthreshold:CH<x> command.

Description

This command specifies the B trigger lower threshold for the channel , where x is the channel number. Each channel can have an independent level. Used in runt and transition triggers as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:B:LOWerthreshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:B:LOWerthreshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LOWerthreshold:CH<x> value command.

SCPI Syntax

- TRIGger:B:LOWerthreshold:CH<x> {ECL|TTL|<NR3>}
- TRIGger:B:LOWerthreshold:CH<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the threshold level, in volts.

d `property` ¶

d: dict[int, TriggerBLowerthresholdDigitalBit]

Return the TRIGger:B:LOWerthreshold:D<x> command.

Description

Sets or queries the lower threshold for the digital channel selected. Each channel can have an independent level. Used in runt and transition triggers as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:B:LOWerthreshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:B:LOWerthreshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LOWerthreshold:D<x> value command.

SCPI Syntax

- TRIGger:B:LOWerthreshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:B:LOWerthreshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerBLowerthresholdChannel ¶

Bases: ValidatedChannel, SCPICmdWrite, SCPICmdRead

The TRIGger:B:LOWerthreshold:CH<x> command.

Description

This command specifies the B trigger lower threshold for the channel , where x is the channel number. Each channel can have an independent level. Used in runt and transition triggers as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:B:LOWerthreshold:CH<x>? query.
Using the .verify(value) method will send the TRIGger:B:LOWerthreshold:CH<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LOWerthreshold:CH<x> value command.

SCPI Syntax

- TRIGger:B:LOWerthreshold:CH<x> {ECL|TTL|<NR3>}
- TRIGger:B:LOWerthreshold:CH<x>?

Info

ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.
<NR3> is a floating point number that specifies the threshold level, in volts.

TriggerBLowerthresholdDigitalBit ¶

Bases: ValidatedDigitalBit, SCPICmdWrite, SCPICmdRead

The TRIGger:B:LOWerthreshold:D<x> command.

Description

Sets or queries the lower threshold for the digital channel selected. Each channel can have an independent level. Used in runt and transition triggers as the lower threshold. Used for all other trigger types as the single level/threshold.

Usage

Using the .query() method will send the TRIGger:B:LOWerthreshold:D<x>? query.
Using the .verify(value) method will send the TRIGger:B:LOWerthreshold:D<x>? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:LOWerthreshold:D<x> value command.

SCPI Syntax

- TRIGger:B:LOWerthreshold:D<x> {<NR3>|ECL|TTL}
- TRIGger:B:LOWerthreshold:D<x>?

Info

<NR3> is a floating point number that specifies the threshold in volts.
ECL specifies a preset ECL high level of -1.3V.
TTL specifies a preset TTL high level of 1.4V.

TriggerBState ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:STATE command.

Description

This command specifies the state of B trigger activity. If the B trigger state is on, the B trigger is part of the triggering sequence. If the B trigger state is off, then only the A trigger causes the trigger event.

Usage

Using the .query() method will send the TRIGger:B:STATE? query.
Using the .verify(value) method will send the TRIGger:B:STATE? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:STATE value command.

SCPI Syntax

- TRIGger:B:STATE {ON|OFF|<NR1>}
- TRIGger:B:STATE?

Info

ON specifies that the B trigger is active and in causes trigger events conjunction with the A trigger.
OFF specifies that only the A trigger causes trigger events.
<NR1> a 0 turns off the B trigger; any other value activates the B trigger.

TriggerBTime ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:TIMe command.

Description

This command specifies B trigger delay time. The B Trigger time applies only if TRIGger:B:BY is set to TIMe.

Usage

Using the .query() method will send the TRIGger:B:TIMe? query.
Using the .verify(value) method will send the TRIGger:B:TIMe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:TIMe value command.

SCPI Syntax

- TRIGger:B:TIMe <NR3>
- TRIGger:B:TIMe?

Info

<NR3> is a floating point number that specifies the B trigger delay time in seconds.

TriggerBType ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:B:TYPe command.

Description

This command specifies the type of B trigger. The only supported B trigger type is EDGE.

Usage

Using the .query() method will send the TRIGger:B:TYPe? query.
Using the .verify(value) method will send the TRIGger:B:TYPe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:B:TYPe value command.

SCPI Syntax

- TRIGger:B:TYPe EDGE
- TRIGger:B:TYPe?

Info

EDGE sets the B trigger type to edge.

TriggerExternal ¶

Bases: SCPICmdRead

The TRIGger:EXTernal command.

Description

Returns all external trigger-related parameters for the probe attached to the Aux Input connector.

Usage

Using the .query() method will send the TRIGger:EXTernal? query.
Using the .verify(value) method will send the TRIGger:EXTernal? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:EXTernal?

Properties

.probe: The TRIGger:EXTernal:PRObe command.
.yunits: The TRIGger:EXTernal:YUNIts command.

probe `property` ¶

probe: TriggerExternalProbe

Return the TRIGger:EXTernal:PRObe command.

Description

This command specifies the attenuation factor value of the probe attached to the Aux Input connector.

Usage

Using the .query() method will send the TRIGger:EXTernal:PRObe? query.
Using the .verify(value) method will send the TRIGger:EXTernal:PRObe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:EXTernal:PRObe value command.

SCPI Syntax

- TRIGger:EXTernal:PRObe <NR3>
- TRIGger:EXTernal:PRObe?

Info

<NR3> is a floating point number that specifies the attenuation factor of the probe.

yunits `property` ¶

yunits: TriggerExternalYunits

Return the TRIGger:EXTernal:YUNIts command.

Description

Returns the vertical (Y) units of the probe attached to the Aux In connector.

Usage

Using the .query() method will send the TRIGger:EXTernal:YUNIts? query.
Using the .verify(value) method will send the TRIGger:EXTernal:YUNIts? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:EXTernal:YUNIts?

TriggerExternalProbe ¶

Bases: SCPICmdWrite, SCPICmdRead

The TRIGger:EXTernal:PRObe command.

Description

This command specifies the attenuation factor value of the probe attached to the Aux Input connector.

Usage

Using the .query() method will send the TRIGger:EXTernal:PRObe? query.
Using the .verify(value) method will send the TRIGger:EXTernal:PRObe? query and raise an AssertionError if the returned value does not match value.
Using the .write(value) method will send the TRIGger:EXTernal:PRObe value command.

SCPI Syntax

- TRIGger:EXTernal:PRObe <NR3>
- TRIGger:EXTernal:PRObe?

Info

<NR3> is a floating point number that specifies the attenuation factor of the probe.

TriggerExternalYunits ¶

Bases: SCPICmdRead

The TRIGger:EXTernal:YUNIts command.

Description

Returns the vertical (Y) units of the probe attached to the Aux In connector.

Usage

Using the .query() method will send the TRIGger:EXTernal:YUNIts? query.
Using the .verify(value) method will send the TRIGger:EXTernal:YUNIts? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:EXTernal:YUNIts?

TriggerFrequency ¶

Bases: SCPICmdRead

The TRIGger:FREQuency command.

Description

Returns the trigger frequency in hertz if available. If the trigger frequency is not currently available, the IEEE Not A Number (NaN = 99.10E+36) value is returned. The maximum precision of the returned frequency is 12 digits. Use the DISPLAY:TRIGFREQUENCY command to enable/disable the calculation of the trigger frequency.

Usage

Using the .query() method will send the TRIGger:FREQuency? query.
Using the .verify(value) method will send the TRIGger:FREQuency? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:FREQuency?

TriggerState ¶

Bases: SCPICmdRead

The TRIGger:STATE command.

Description

This query-only command returns the current state of the triggering system.

Usage

Using the .query() method will send the TRIGger:STATE? query.
Using the .verify(value) method will send the TRIGger:STATE? query and raise an AssertionError if the returned value does not match value.

SCPI Syntax

- TRIGger:STATE?

trigger ¶

Trigger ¶

a property ¶

b property ¶

external property ¶

frequency property ¶

state property ¶

TriggerA ¶

bandwidth property ¶

bus property ¶

edge property ¶

holdoff property ¶

level property ¶

logic property ¶

lowerthreshold property ¶

mode property ¶

pulse property ¶

pulsewidth property ¶

risefall property ¶

runt property ¶

sethold property ¶

timeout property ¶

transition property ¶

type property ¶

upperthreshold property ¶

video property ¶

TriggerABandwidth ¶

rf property ¶

TriggerABandwidthRf ¶

high property ¶

low property ¶

TriggerABandwidthRfHigh ¶

TriggerABandwidthRfLow ¶

TriggerABus ¶

b property ¶

source property ¶

TriggerABusBItem ¶

arinc429a property ¶

audio property ¶

can property ¶

ethernet property ¶

flexray property ¶

i2c property ¶

lin property ¶

mil1553b property ¶

parallel property ¶

rs232c property ¶

spi property ¶

usb property ¶

TriggerABusBItemArinc429a ¶

condition property ¶

errtype property ¶

label property ¶

sdi property ¶

ssm property ¶

TriggerABusBItemArinc429aCondition ¶

TriggerABusBItemArinc429aErrtype ¶

TriggerABusBItemArinc429aLabel ¶

hivalue property ¶

qualifier property ¶

value property ¶

TriggerABusBItemArinc429aLabelHivalue ¶

TriggerABusBItemArinc429aLabelQualifier ¶

TriggerABusBItemArinc429aLabelValue ¶

TriggerABusBItemArinc429aSdi ¶

TriggerABusBItemArinc429aSsm ¶

TriggerABusBItemAudio ¶

condition property ¶

data property ¶

TriggerABusBItemAudioCondition ¶

TriggerABusBItemAudioData ¶

hivalue property ¶

offset property ¶

qualifier property ¶

value property ¶

word property ¶

TriggerABusBItemAudioDataHivalue ¶

TriggerABusBItemAudioDataOffset ¶

TriggerABusBItemAudioDataQualifier ¶

TriggerABusBItemAudioDataValue ¶

a `property` ¶

b `property` ¶

external `property` ¶

frequency `property` ¶

state `property` ¶

bandwidth `property` ¶

bus `property` ¶

edge `property` ¶

holdoff `property` ¶

level `property` ¶

logic `property` ¶

lowerthreshold `property` ¶

mode `property` ¶

pulse `property` ¶

pulsewidth `property` ¶

risefall `property` ¶

runt `property` ¶

sethold `property` ¶

timeout `property` ¶

transition `property` ¶

type `property` ¶

upperthreshold `property` ¶

video `property` ¶

rf `property` ¶

high `property` ¶

low `property` ¶

b `property` ¶

source `property` ¶

arinc429a `property` ¶

audio `property` ¶

can `property` ¶

ethernet `property` ¶

flexray `property` ¶

i2c `property` ¶

lin `property` ¶

mil1553b `property` ¶

parallel `property` ¶

rs232c `property` ¶

spi `property` ¶

usb `property` ¶

condition `property` ¶

errtype `property` ¶

label `property` ¶

sdi `property` ¶

ssm `property` ¶

hivalue `property` ¶

qualifier `property` ¶

value `property` ¶

condition `property` ¶

data `property` ¶

hivalue `property` ¶

offset `property` ¶

qualifier `property` ¶

value `property` ¶

word `property` ¶

address `property` ¶

condition `property` ¶

data `property` ¶

fd `property` ¶

frametype `property` ¶

identifier `property` ¶

mode `property` ¶

value `property` ¶

direction `property` ¶

offset `property` ¶

qualifier `property` ¶

size `property` ¶

value `property` ¶

brsbit `property` ¶

esibit `property` ¶

mode `property` ¶

value `property` ¶

condition `property` ¶

data `property` ¶

frametype `property` ¶

ipheader `property` ¶

mac `property` ¶

qtag `property` ¶

qualifier `property` ¶

tcpheader `property` ¶